5019 407 00223
1. Check that all fastenings are closed and
that pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to
make sure it doesn’t become tangled.
Sort laundry as follows:
A) By care symbols
(on the collar or inside seam):
Suitable for tumble drying
Tumble drying with reduced
drying intensity only. Press
Gentle button.
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds
dryer capacity, separate laundry according
to weight (e.g. towels from thin
underwear).
C) By type of fabrics
Cotton/linen: Towels, cotton jersey, bed
and table linen made of cotton or linen.
Synthetics/Easy Care: blouses, shirts,
overalls, etc. made of polyester or
polyamide, as well as cotton/synthetic
mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry: Woollens, silk, nylon
stockings, delicate embroidery, fabrics
with metallic decorations, bulky items such
as sleeping bags, etc.
Important: only use specific indicated
dryer-safe additives and rinse items
that have been treated with stain remover
thoroughly in plenty of water before
drying. Only use specific indicated
dryer-safe plastic items and never dry
rubber or articles contaminated with
vegetable oil in the dryer.
Programme and Options:
• To select a programme, turn the
programme selector knob. The start
indicator lamp is blinking, indicating
that the cycle needs to be started.
• To select an option, press the
corresponding button. The indicator
lamp in the button confirms that a
selection has been made.
• Press the button again to cancel the
option.
1. Having selected the desired
programme and options, press the
Start/Pause button.
As soon as the drying cycle is finished
the END indicator lamp is lit and the
laundry can be removed.
If the laundry is not removed at the end
of the drying cycle, an automatic anti-
crease cycle will operate for maximum
60 min. The drum rotates at regular
intervals, preventing the laundry from
creasing.
Anti-Crease protection re-distributes
laundry in the drum.
2. On completion of the programme, set
the programme selector knob to
position “0”.
When changing the programme during
the drying cycle, the dryer stops. The start
indicator lamp is blinking.
To operate the new programme, press the
Start/Pause button again.
To interrupt the dryer during operation
1. Set the programme selector knob to
Airing.
2. Press the Start button.
Wait at least 5 minutes before opening
the door to allow the dryer to cool down.
For your safety the programme stops
automatically if you open the door.
3. To restart, after door opening, close
the door and press the Start/Pause
button again.
Clean the lint filter at the end of every
drying cycle:
1. Open the door.
2. Pull the filter upwards.
3. Remove lint using a soft brush or your
fingertips.
4. Push the filter back into place.
If a fault occurs, before contacting our
After-Sales Service, make the following
checks to try and remedy the problem:
Drying takes too long / laundry is not
dry enough:
• Was the correct programme selected?
• Was the inserted laundry too wet
(Washing machine spin speed less than
800 rpm)?
• Is the lint filter dirty (filter indicator lamp
on)?
The dryer does not operate:
(after a power failure and/or
interruption to the mains supply,
always press the Start button).
• Is the plug properly inserted into the
mains electricity socket?
• Is there a power failure?
• Has the fuse blown?
• Is the door well closed?
• Has the programme been selected?
• Has the Start/Pause button been
pressed?
Lint filter indicator lamp light on:
• Is the lint filter clean?
• Is the vent hose blocked?
If, after carrying out the above checks
the malfunction persists or appears
again, turn the dryer off and call our
After-Sales Service (refer to guarantee).
Please specify:
• The nature of the fault.
• The dryer type and model.
• The service code (the number after the
word Service on the adhesive rating
plate) on the right-hand side when the
door is open.
• Your full address and phone number.
PREPARING THE LAUNDRY SELECTING A PROGRAMME & OPTIONS
STARTING & COMPLETING A
PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE & CLEANING
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE