Lennox Elite EBBAYNE Installation Instructions Manual

Marque: Lennox

Modèle: Elite EBBAYNE

Catégorie: Cheminées

Taper: Installation Instructions Manual

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

INSTALLATION

INSTRUCTIONS

RETAIN THESE INSTRUCTIONS

FOR FUTURE REFERENCE

FOR YOUR SAFETY: Do not store or use gasoline

or other flammable vapors or liquids in the vicin-

ity of this or any other appliance.

FOR YOUR SAFETY: What to do if you smell gas:

• DO NOT light any appliance.

• DO NOT touch any electrical switches.

• DO NOT use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow your gas suppliers

instructions.

• If your gas supplier cannot be reached, call the

fire department.

Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

MODELS

POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser

d'essence ni d'autre vapeurs ou liquides inflammables

dans le voisinage de cet appareil ou de tout autre

appareil.

POUR VOTRE SÉCURITÉ: Que faire si vous sentez une

odeur de gaz:

• Ne pas tenter d'allumer d'appareil.

• Ne touchez à aucun interrupteur. Ne pas vous servir

des téléphones se trouvant dans le batiment où

vous vous trouvez.

• Evacuez la piéce, le bâtiment ou la zone.

• Appelez immédiatement votre fournisseur de gaz

depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service dos incendies.

L'installation et service doit être exécuté par un qualifié

installeur, agence de service ou le fournisseur de gaz.

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE

LES INSTRUCTIONS DONNÉ DANS CETTE NOTICE POUR

RÉDUIRE AU MINIMUM LE RISQUE D'INCENDIE OU

POUR ÉVITER TOUT DOMMAGE MATÉRIEL, TOUTE

BLESSURE OU LA MORT.

WARNING: IF THE INFORMATION IN THIS MANUAL

IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-

SION MAY RESULT CAUSING PROPERTY DAM-

AGE, PERSONAL INJURY OR LOSS OF LIFE.

B-VENT MULTI-OPEN

ELITE

SERIES

B-VENTED GAS FIREPLACES

P/N 850,008M REV. H 05/2004

This appliance may be installed in an aftermar-

ket permanently located, manufactured home

(USA only) or mobile home, where not prohib-

ited by local codes. This appliance is only for

use with the type of gas indicated on the rating

plate. This appliance is not convertible for use

with other gases, unless a certified kit is used.

sledoMtlovilliMsledoMcinortcelE

2-MNTSBE2-MNRCBE2-ENTSBE2-ENRCBE

2-MPTSBE2-MPRCBE2-EPTSBE2-EPRCBE

2-MNFPBE2-MNLCBE2-ENFPBE2-ENLCBE

2-MPFPBE2-MPLCBE2-EPFPBE2-EPLCBE

MNYABBEPNYABBEENYABBE

OTL Report No. 116-F-07-5

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Offset Venting

Vertical Venting

Figure 1

Millivolt Models -

Millivolt models come standard with the

manually-modulated gas valve; flame ap-

pearance and heat output can be con-

trolled at the gas valve. Input of millivolt

models is shown in the following table:

Electronic appliances are designed to operate

on natural or propane gas. An electronic inter-

mittent pilot ignition system provides safe,

efficient operation. External electrical power is

required to operate these units.

These appliances comply with National Safety

Standards and are tested and listed by Omni-

Test Laboratories (Report No. 116-F-07-5) to

ANSI Z21.50 - 2000 (in Canada, CSA 2.22 -

2000), and CAN/CGA-2.17-M91 in both USA

and Canada, as vented gas fireplaces.

These appliances may be used for bedroom

installations in the United States and are

listed accordingly. These units may not be

installed in bedrooms in Canada.

Installation must conform to local codes. In the

absence of local codes, installation must com-

ply with the current National Fuel Gas Code,

ANSI Z223.1. (In Canada, the current CAN-1

B149 installation code.) Electrical wiring must

comply with the National Electrical Code ANSI/

NFPA 70 - (latest edition). (In Canada, the

current CSA C22-1 Canadian Electrical Code.)

TABLE OF CONTENTS

Packaging ........................................ page 2

Introduction ..................................... page 2

General Information......................... page 2

Location .......................................... page 4

Appliance and Vent Clearances ....... page 4

Vent Termination Clearances ........... page 4

Typical Installation Sequence .......... page 4

Detailed Installation Steps ............... page 5

Step 1. Framing ............................. page 5

Step 2. Routing Gas Line ............... page 5

Step 3. Install the Venting System . page 5

Fireplace Specifications ................... page 6

Step 4. Field Wiring ....................... page 10

Step 5. Connecting Gas Line.......... page 11

Step 6. Outside Air Kit Installation . page 12

Step 7. Installing Logs ................... page 13

Step 8. Checking Unit Operation ..... page 13

Step 9. Installing Glass Enclosure

Panels.......................................... page 13

Step 10. Burner Adjustment ............ page 14

Step 11. Spillage Test and Safety

Limit Switch Operation ................ page 14

Step 12. Hood Installation ............... page 15

Finishing Requirements ................... page 15

Cold Climate Insulation.................... page 15

Gas Conversion Kits.................. page 16

TYPICAL INSTALLATION

DO NOT ATTEMPT TO ALTER OR MODIFY

THE CONSTRUCTION OF THE APPLIANCE OR

ITS COMPONENTS. ANY MODIFICATION OR

ALTERATION MAY VOID THE WARRANTY,

CERTIFICATION AND LISTINGS OF THIS UNIT.

INTRODUCTION

Note: Installation and repair should be per-

formed by a qualified service person. The appli-

ance should be inspected annually by a quali-

fied professional service technician. More fre-

quent inspections and cleanings may be re-

quired due to excessive lint from carpeting,

bedding material, etc. It is imperative that the

control compartment, burners and circulating

air passage ways of the appliance be kept clean.

S'assurer que le brùleur et le compartiment des

commandes sont propres. Voir les instruc-

tions d'installation et d'utilisation qui

accompagnent l'appareil.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front, back and/or side viewing surfaces of

the appliance.

These appliances are designed to operate on

natural or propane gas only. The use of other fuels

or combination of fuels will degrade the perfor-

mance of this system and may be dangerous.

This installation manual will help you achieve a

safe, efficient and dependable installation for

your appliance and vent system.

Please read and understand these

instructions before beginning your

installation.

WARNING: THESE FIREPLACES ARE

VENTED DECORATIVE GAS APPLIANCES.

DO NOT BURN WOOD OR OTHER MATE-

RIAL IN THESE APPLIANCES.

GENERAL INFORMATIONPACKAGING

The assembled vented gas fireplace is pack-

aged with:

1 -one log set, with one plastic bag of vermicu-

lite, is packaged in a carton located within

the firebox.

2 - one envelope containing the literature pack-

age, which consists of the homeowner's

manual, installation instructions, warranty,

8 (EBST-2), 4 (EBPF-2, EBCR-2, EBCL-2

and EBBAY) nailing flanges; envelope is

located in the control area.

3 - two hoods (EBST-2, EBCR-2, EBCL-2), or three

hoods (EBPF-2, EBBAY) taped to the top of the

fireplace.

4 - one plastic bag of glowing embers and one

plastic bag of decorative volcanic stone

is located in the bottom compartment.

These vented gas fireplaces are designed for

residential applications. They must be installed

with approved type-B, 6 in. double wall vent

pipe systems routed to the outside atmosphere.

The millivolt appliances are designed to operate

on either natural or propane gas. A millivolt gas

control valve with piezo ignition system provides

safe, efficient operation. If any optional accesso-

ries which require electrical power are being

installed, the electrical power must be provided

at the time of appliance installation.

sledoMtlovilliM

enaporPdnalarutaN

sledoMsaG

)H/UTB(etartupnI

detaludom-yllaunaM

,2-MNFPBE,2-MNTSBE

,2-MPFPBE,2-MPTSBE

PNYABBE,MNYABBE

005,73OT000,03

,2-MNRCBE,2-MNLCBE

2-MPRCBE,2-MPLCBE

000,43OT000,62

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

* Each model has two burners. Each burner contains one

of these orifices.

sledoMcinortcelE

enaporPdnalarutaN

sledoMsaG

)H/UTB(etartupnI

etaRdexiF

,2-ENFPBE,2-ENTSBE

,2-EPFPBE,2-EPTSBE

ENYABBE

005,73

,2-ENRCBE,2-ENLCBE

2-EPRCBE,2-EPLCBE

000,43

ledoM

.oN

*ezisecifirO

noitavelE

)sretem(teeF

.taN.porP

2-TSBE

2-FPBE

YABBE

44#55#

0054-0

)2731-0(

2-RCBE

2-LCBE

74#"50.0

Table 1

Test gage connections are provided on the

front of the millivolt gas control valve (iden-

tified IN for the inlet and OUT for the mani-

fold side). A ¹⁄₈" NPT test gage connection is

provided at the inlet and outlet side of

the electronic gas control valve.

Minimum inlet gas pressure to these appliances

is 5.0 inches water column (1.24 kPa) for natural

gas and 11.0 inches water column (2.74 kPa) for

propane for the purpose of input adjustment.

Maximum inlet gas supply pressure to these

appliances is 10.5 inches water column (2.61

kPa) for natural gas and 13.0 inches water

column (3.23 kPa) for propane.

Do not use these appliances if any part has been

under water. Immediately call a qualified, pro-

fessional service technician to inspect the ap-

pliance and to replace any parts of the control

system and any gas control which have been

under water.

The millivolt appliances are manually controlled

and feature a spark ignitor (piezo) that allows

the appliance's pilot gas to be lit without the use

of matches or batteries. This system will still

function in the event of a power outage.

Installations at Altitudes of 0 to 4500 ft.-

Units are tested and approved for elevations

of 0 to 4500 feet (0 to 1372 meters).

Installations at Altitudes above 4500 ft.-

For elevations above 4500 feet (1372

meters), install the unit according to the

regulations of the local authorities having

jurisdiction and, in the USA, the latest edition

of the National Fuel Gas Code (ANSI Z223.1)

or, in Canada, the latest edition of the

CAN1-B149.1 and .2 codes.

Table 1

shows the units' gas orifice size for

the elevations indicated.

WARNING: FAILURE TO COMPLY WITH

THE INSTALLATION AND OPERATING IN-

STRUCTIONS PROVIDED IN THIS DOCU-

MENT WILL RESULT IN AN IMPROP-

ERLY INSTALLED AND OPERATING AP-

PLIANCE, VOIDING ITS WARRANTY. ANY

CHANGE TO THIS APPLIANCE AND/OR

ITS OPERATING CONTROLS IS DANGER-

OUS. IMPROPER INSTALLATION OR USE

OF THIS APPLIANCE CAN CAUSE SERI-

OUS INJURY OR DEATH FROM FIRE,

BURNS, EXPLOSION OR CARBON MON-

OXIDE POISONING.

These appliances must be isolated from the gas

supply piping system (by closing their individual

manual shut-off valve) during any pressure test-

ing of the gas supply piping system at test

pressures equal to or less than ¹⁄₂ psig (3.5 kPa).

These appliances and their individual shut-off

valves must be disconnected from the gas

supply piping system during any pressure test-

ing of that system at pressures in excess of ¹⁄₂

psig (3.5 kPa).

These appliances must not be connected to

a chimney or flue serving a separate solid

fuel burning appliance.

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning are similar to

the flu with headaches, dizziness and/or

nausea. If you have these signs, obtain

fresh air immediately. Turn off the gas

supply to the appliance and have it ser-

viced by a qualified professional, as it may

not be operating correctly.

WARNING: CHILDREN AND ADULTS

SHOULD BE ALERTED TO THE HAZARDS

OF HIGH SURFACE TEMPERATURES. USE

CAUTION AROUND THE APPLIANCE TO

AVOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CARE-

FULLY SUPERVISED WHEN THEY ARE IN

THE SAME ROOM AS THE APPLIANCE.

WARNING: DO NOT PLACE CLOTHING

OR OTHER FLAMMABLE MATERIALS

ON OR NEAR THIS APPLIANCE.

AVERTISSEMENT: SURVEILLER LES

ENFANTS. GARDER LES VÊTEMENTS,

LES MEUBLES, L'ESSENCE OU AUTRES

LIQUIDES À VAPEUR INFLAMMABLES À

COTE DE L'APPAREIL.

Electronic Models -

Electronic models have a fixed rate gas valve.

Input of electronic models is shown in the

following table:

All Models -

Maximum manifold pressure is 3.5 in. w.c.

(0.87 kPa) for natural gas and 10 in. w.c.

(2.49 kPa) for LP/Propane gas.

WARNING: B-VENT APPLIANCES ARE NOT

DESIGNED TO OPERATE IN NEGATIVELY

PRESSURED ENVIRONMENTS (PRESSURE

WITHIN THE HOME IS LESS THAN PRES-

SURES OUTSIDE). SIGNIFICANT NEGA-

TIVELY PRESSURED ENVIRONMENTS

CAUSED BY WEATHER, HOME DESIGN,

OR OTHER DEVICES MAY IMPACT THE

OPERATION OF THESE APPLIANCES.

NEGATIVE PRESSURES MAY RESULT IN

POOR FLAME APPEARANCE, SOOTING,

DAMAGE TO PROPERTY AND/OR SEVERE

PERSONAL INJURY. DO NOT OPERATE

THESE APPLIANCES IN NEGATIVELY PRES-

SURED ENVIRONMENTS. PROVIDING AD-

EQUATE VENTILATION TO THE APPIANCE

FOR COMBUSTION AIR WILL ELIMINATE A

NEGATIVE PRESSURE ENVIRONMENT.

This appliance may be installed in an af-

termarket permanently located, manufac-

tured home (USA only) or mobile home,

where not prohibited by local codes. This

appliance is only for use with the type of

gas indicated on the rating plate. This ap-

pliance is not convertible for use with

other gases, unless a certified kit is used.

Cet appareil peut être installé dans un maison

préfabriquée (É.-U. seulement) ou mobile

déjà installée à demeure si les réglements

locaux le permettent.

Cet appareil doit être utilisé uniquement avec

les types de gaz indiqués sur la plaque

signalétique. Ne pas l'utiliser avec d'autres gaz

sauf si un kit de conversion certifié est installé.

These appliances are equipped with an inte-

gral combustion air door and actuator arm.

Combustion air kits are optional.Install as

shown in Step 6 on page 12.

Ne pas se servir de cet appareil s'il a été plongé

dans l'eau, complètement ou en partie. Appeler

un technicien qualifié pour inspecter l'appareil et

remplacer toute partie du système de contrôle et

toute commande qui ont été plongés dans l'eau.

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

TYPICAL LOCATIONS

**See-Through

(EBST-2)

Corner - Left

(EBCL-2)

Corner - Right

(EBCR-2)

Peninsula

(EBPF-2)

*When See-Through (EBST-2) is

installed with one side flush

with a wall,opposite wall must

not extend beyond either

viewing side of the fireplace.

*See-Through

(EBST-2) -

one side flush with a wall

**When See-Through (EBST-2) is

installed in the middle of a room,

do not extend side walls beyond

either viewing side of the fireplace.

Bay

(EBBAY)

KCAB

)mm31(.ni2/1

srecaps)mm0(.ni0

SEDIS

)mm31(.ni2/1

srecaps)mm0(.ni0

SRECAPSPOT )mm0(.ni0

ROOLF )mm0(.ni0

mottoBmorF

ottinUfo

gnilieC

)mm6261(.ni46

TNEV )mm4.52(.ni1

SECNARAELCECIVRES

GNIWEIV

-SEDIS

KCAB,TNORF(

)EDISRO

)sretem9.0(.teeF3

Figure 3

Figure 2

APPLIANCE AND VENT CLEARANCES

The appliance is approved with zero clearance to

combustible materials on all sides (as detailed in

Table 2)

, with the following exception: When the

unit is installed with one side flush with a wall,

the wall on the other side of the unit must not

extend beyond the front edge of the unit. In

addition, when the unit is installed in the middle

of a room, the side walls surrounding the unit

must not extend beyond the front or rear edge

of the unit. See

Figure 2

LOCATION

In selecting the location, the aesthetic and func-

tional use of the appliance are primary concerns.

However, vent system routing to the outside

atmosphere and access to the fuel supply are

also important. Consideration should be given to

traffic ways, furniture, draperies, etc., due to high

surface temperatures (

Figure 2

). The location

should also be free of electrical, plumbing or

other heating/air conditioning ducting.

The appliance should be mounted on a fully

supported base extending the full width and

depth of the unit. The appliance may be located

on or near conventional construction materi-

als. However, if installed on combustible mate-

rials, such as carpeting, vinyl tile, etc., a metal

or wood barrier covering the entire bottom

surface must be used.

Table 2

Vertical Vent Termination Clearances

Gas Vent Rule – Gas vent caps are not permit-

ted within 8 feet (2.4 mm) of a vertical wall or

similar obstruction. Gas vent caps that are

located 8' or more from a portion of a building

which extends at an angle greater than 45°

upward from the horizontal may terminate in

accordance with

(Figure 3 )

, provided that in

no case shall any discharge opening on the

cap be less than 2' (610 mm) horizontally from

the roof surface (National Fuel Gas Code ANSI

Z223.1 (NFPA 54) 7.6.2) (CAN/CGA B149).

Flat to 6/12 1' 0" 0.3

Over 7/12 to 9/12 2' 0" 0.6

Over 10/12 to 12/12 4' 0" 1.2

Over 13/12 to 16/12 6' 0" 1.8

Over 17/12 to 21/12 8' 0" 2.4

Roof Slope

Feet Meters

Minimum Height

from Roof to Lowest

Discharge Opening

Note: Venting terminals shall not be recessed

into a wall or siding.

Multiple Terminations – These appliances may

vent adjacent to and at the same level with any

other gas appliances (including direct-vent ap-

pliances) provided that there is at least 2 ft.

(0.6m) between the proximal edges of the vent

caps. These appliances may be vented adja-

cent to a chimney vent servicing a solid fuel

fireplace provided the B-vent cap is at least 2 ft.

(0.6m) away from the nearest point of the

chimney opening.

These instructions should be used as a guide-

line and do not supersede local codes in any

way.

Roof Pitch is X/12

Minimum Height from Roof

to Lowest Discharge Opening

TYPICAL INSTALLATION SEQUENCE

The typical sequence of installation follows,

however, each installation is unique resulting

in variations to those described.

See the page numbers references in the fol-

lowing steps for detailed procedures.

Step 1. (page 5) Construct the appliance

framing. Position the appliance within the

framing and secure with nailing brackets.

Step 2. (page 5) Route gas supply line to

appliance location.

Step 3. (page 5) Install the vent system

and exterior termination.

Step 4. (page 10) Field Wiring

a. Millivolt Appliances – The operating con-

trol switch is factory installed.

b. Electronic Appliances – Connect 120 Vac

electrical power to the appliance receptacle.

Step 5. (page 11) Make connection to gas

supply.

Step 6. (page 12) Outside Air Kit Installation

Step 7. (page 13) Install the log set, ver-

miculite and ceramic fiber chunks.

Step 8. (page 13) Checkout appliance op-

eration.

Step 9. (page 13) Install glass enclosure

panels.

Step 10. (page 14) Burner Adjustment.

Step 11. (page 14) Spillage Test and Safety

Limit Switch Operation.

Step 12. (page 15) Install the hoods.

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Top Radiant

Panel

Top Bustle

Bottom

Bustle

Control

Compartment

Access Panel

Unit Parts Identification

Figure 4

Step 3. Install the Vent System & Exterior

Termination -

In the United States, vent installation must

conform with local building codes. In the ab-

sence of local codes, vents must be installed in

accordance with the current edition of the

National Fuel Gas Code (ANSI-Z223.1).

In Canada, vent installation must conform

with local building codes. In the absence of

local codes, vents must be installed in ac-

cordance with the current edition of the Na-

tional Standard of Canada CAN/CGA-B149.1

or B149.2 Installation Code.

This gas fireplace must be vertically vented

using listed 6 in. type-B, double-walled vent

pipe and a listed vent termination.

Slip the first 6 inch (152 mm) section of B-

Vent over the fireplace flue outlet and secure

with four sheetmetal screws (# 8 or larger),

and install the remainder of the B-Vent to the

outside. Minimum overall height of the vent

system and appliance must be 10' (2.54 m)

vertical - no offset

(see Figure 6 on page 6 );

or 12' (3.7 m) when an offset up to 60

degrees from the vertical is used - this offset

may start at the fireplace flue collar

(see

Figure 7 on page 6 ).

The maximum overall

height of the vent system and appliance

should not exceed 40 feet.

Install the B-vent system in accordance with

the vent manufacturer's instructions.

CAUTION: THIS APPLIANCE CANNOT BE

VENTED HORIZONTALLY.

Note: Refer to the vent manufacturers in-

stallation instructions for variations of vent-

ing techniques. If common venting of sev-

eral units is contemplated, it should be dis-

cussed with an architect and the local Build-

ing Department.

Do not place insulation materials within 1 in.

of the gas vent system.

If the appliance is to be elevated above floor level,

a solid continuous platform must be constructed.

Headers may be in direct contact with the appli-

ance top spacers but must not be supported by

them or notched to fit around them. All construc-

tion above the appliance must be self supporting,

DO NOT use the appliance for structural support.

Step 2. ROUTING GAS LINE

3- Open the control compartment access

panel, by actuating the spring-loaded mag-

netic catches securing the panel, gently de-

pressing the outer top corners of the panel

until the catches "pop" the panel free and

allowing it to swing out and down to open.

4 - Remove the bottom control compartment

access panel by compressing the spring-loaded

hinge pin on the left side until it disengages

from the left cabinet panel hole. Pull the panel

away from the fireplace.

See Figure 22 on

page 12.

5 - Remove the modesty panel by pulling the

bottom right corner of the modesty panel out

slightly to disengage the snap-fit feature; lift

the modesty panel by the tab on the panel's

right end, pull the right end of the panel away

from the cabinet and then pull the panel diago-

nally out of the left side cabinet panel slots. (In

the above procedure, reverse the words "left"

and "right" for EBCR-2 models). Remove the

modesty panel carefully, so that none of the

wires become loose or disconnected.

Side Nailing Flanges

The fireplace should be secured to the framing at

the side(s) and/or rear of the unit using the

factory-provided nailing flanges. Install the nail-

ing flanges - 8 (EBST-2), 4 (EBPF-2, EBCL-2,

EBCR-2 and EBBAY) - as shown in

Figure 5

using the existing screws. Position the fireplace

within the framing. When required, the flanges

may be bent 90 degrees by hand or with the

assistance of a hammer. Use wood screws to

secure the nailing flanges to the framing.

See

Table 2 on page 4

for clearances of framing

members to cabinet parts in the nailing flange

area. The nailing flange itself is exempt from

these clearances.

Figure 5

Step 1. FRAMING

Frame these appliances as illustrated in

Figures 8 (EBST-2), 9 (EBPF-2), 10

(EBCL-2), 11 (EBCR-2) or 12 (EBBAY) on

pages 6 and 7.

All framing details must

allow for a minimum clearance to com-

bustible framing members as shown

Table 2 on page 4

DETAILED INSTALLATION STEPS

The appliance is shipped with all gas controls

and components installed and pre-wired.

1 - Remove the shipping carton.

2 - Remove the top radiant panel;

see Figure 4.

Floor Nailing Tabs

Secure the fireplace to the floor as shown in

Figure 5.

All appliances are factory-equipped with a flex-

ible gas line connector and ¹⁄₂ inch shutoff valve.

(See step 5 on page 11).

6 - Open the latch (located in the center of the

unit front opening, under the firebox floor) secur-

ing the glass enclosure panel. Remove the panel

by tilting it outward at the bottom and lifting it up.

Set the door aside protecting it from inadvertent

damage.

See Figure 22 on page 12.

Route a ¹⁄₂" (13 mm) gas line as shown in

Figure 8 (EBST-2), 9 (EBPF-2), 10 (EBCL-2),

11 (EBCR-2) or 12 (EBBAY) on pages 6 and 7

Gas lines must be routed, constructed and

made of materials that are in strict accordance

with local codes and regulations.

Turn tabs down and secure to the floor with

8d nails or other appropriate fasteners on all sides

of the unit which do not have viewing glass panels.

EBST-2 SHOWN

(EBPF-2 - NO NAILING FLANGES ON END WITH GLASS PANEL)

EBCL-2 SHOWN

(FOR EBCR-2 VIEW, INTERCHANGE SIDES)

Remove these two screws and use them

when installing the nailing flanges.

Nailing

Flanges

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 6

Figure 7

10 ft.

Minimum

12 ft.

Minimum

60 degrees

max.

FIREPLACE FRAMING SPECIFICATIONS

Gas Line

Center of gas line

is 3 in. (76 mm)

up from floor.

*41¹⁄₂

(1054)

41¹⁄₂

(1054)

*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm)

clearance between framing and unit framing spacers. (The 41¹⁄₂ in. dimension permits

easier fireplace installation, if unit is installed after framing is erected.)

22³⁄₄**

(578)

EBST-2

(See-Through)

inches (millimeters)

6¹⁄₄

(159)

Minimum Framing

Stud size is 2 x 4

**Based on 5/8” drywall. Use 23” for 1/2” drywall.

*41¹⁄₂

(1054)

40¹⁄₈

(1019)

EBPF-2

(Peninsula)

inches (millimeters)

Gas Line

Center of gas line

is 3 in. (76 mm)

up from floor.

6¹⁄₄

(159)

Minimum Framing

Stud size is 2 x 4

*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm)

clearance between framing and unit framing spacers. (The 41¹⁄₂ in. dimension permits

easier fireplace installation, if unit is installed after framing is erected.)

22³⁄₄**

(578)

**Based on 5/8” drywall. Use 23” for 1/2” drywall.

Figure 9

Figure 8

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

*41¹⁄₂

(1054)

40¹⁄₈

(1019)

(610)

*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm)

clearance between framing and unit framing spacers. (The 41¹⁄₂ in. dimension

permits easier fireplace installation, if unit is installed after framing is erected.)

EBCR-2 (Corner-Right)

inches (millimeters)

Gas Line

Center of gas line

is 3 in. (76 mm)

up from floor.

9⁷⁄₈

(251)

Minimum Framing

Stud size is 2 x 4

Figure 11

FIREPLACE FRAMING SPECIFICATIONS CONTINUED

*41¹⁄₂

(1054)

40¹⁄₈

(1019)

*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm)

clearance between framing and unit framing spacers. (The 41¹⁄₂ in. dimension permits easier

fireplace installation, if unit is installed after framing is erected.)

(610)

EBCL-2 (Corner-Left)

inches (millimeters)

6¹⁄₄

(159)

9³⁄₄

(248)

Optional Gas Line

Location Center of gas line

is 3 in. (76 mm) up from floor.

Gas Line

Center of gas line

is 3 in. (76 mm)

up from floor.

Minimum Framing

Stud size is 2 x 4

Figure 10

Figure 12

*41¹⁄₂

(1054)

40¹⁄₈

(1019)

*This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm)

clearance between framing and unit framing spacers. (The 41¹⁄₂ in. dimension permits easier

fireplace installation, if unit is installed after framing is erected.)

EBBAY (Bay)

inches (millimeters)

7 ⁵⁄₈

(194)

Gas Line

Location Center of gas line

is 3 in. (76 mm) up from floor.

Minimum Framing

Stud size is 2 x 4

23¹⁄₄

(591)

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

EBST-2 (See-Through)

(1041)

(940)

40¹⁄₈

(1019)

6⁷⁄₈

(175)

(305)

12 (305)

20¹⁄₁₆

(510)

(70)

FRONT VIEW

RIGHT SIDE VIEWLEFT SIDE VIEW

TOP VIEW

3 (76)

4 (102)

¹⁄₂ (13)

GAS INLET

40¹⁄₈

(1019)

3 (76)

ELECTRICAL

INLETS

A - 6 (152) DIA. FLUE OUTLET

FRAMING SPACERS

(Top and Both Sides)

(610)

CONTROL

COMPARTMENT

ACCESS PANEL

FINISH WALL BRACKET

(Front and back edge of unit top)

1/2

(13)

DETAIL OF

FINISH WALL BRACKET

¹⁄₂ (13)

2³⁄₄

ELECTRICAL

INLETS

B - 8 (203) DIA. FLUE COLLAR

6⁷⁄₈

(175)

4⁹⁄₁₆

(116)

4⁹⁄₁₆

(116)

OUTSIDE AIR

SHUTTER

EBPF-2 (Peninsula)

12 (305)

20¹⁄₁₆

(510)

TOP VIEW

40¹⁄₈

(1019)

FRAMING SPACERS

(Top and Side)

FINISH WALL BRACKET

(Front, back, and left edge of unit top)

6⁷⁄₈

(175)

(305)

(70)

RIGHT SIDE VIEW

LEFT SIDE VIEW

3 (76)

(13)

DETAIL OF

FINISH WALL BRACKET

2³⁄₄

¹⁄₂

4⁹⁄₁₆

(116)

OUTSIDE AIR

SHUTTER

A - 6 (152) DIA. FLUE OUTLET

B - 8 (203) DIA. FLUE COLLAR

(610)

(1041)

(940)

¹⁄₂

(13)

FRONT VIEW

4 (102)

GAS INLET

ELECTRICAL

INLETS

CONTROL COMPARTMENT

ACCESS PANEL

Figure 13

Figure 14

FIREPLACE SPECIFICATIONS

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

EBCL-2 (Corner-Left)

(1041)

(940)

6⁷⁄₈

(175)

(305)

12 (305)

(13)

(70)

FRONT VIEW RIGHT SIDE VIEW

LEFT SIDE VIEW

TOP VIEW

3 (76)

4 (102)

40¹⁄₈

(1019)

GAS INLET

ELECTRICAL

INLETS

FRAMING SPACERS

(Top, Side and Back)

(13)

DETAIL OF

FINISH WALL BRACKET

(Front and left edge of unit top)

CONTROL COMPARTMENT

ACCESS PANEL

¹⁄₂

2³⁄₄

20¹⁄₁₆

(510)

OUTSIDE AIR

SHUTTER

4⁹⁄₁₆

(116)

A - 6 (152) DIA. FLUE OUTLET

B - 8 (203) DIA. FLUE COLLAR

(13)

¹⁄₂

(610)

6⁷⁄₈

(175)

(305)

2³⁄₄

(70)

3 (76)

(13)

(1041)

(940)

(610)

12 (305)

FRONT VIEW

LEFT SIDE VIEW

TOP VIEW

4 (102)

40¹⁄₈

(1019)

GAS INLET

ELECTRICAL

INLETS

FRAMING SPACERS

(Top, Side and Back)

(13)

DETAIL OF

FINISH WALL BRACKET

RIGHT SIDE VIEW

EBCR-2 (Corner-Right)

FINISH WALL BRACKET

(Front and right edge of unit top)

¹⁄₂

CONTROL COMPARTMENT

ACCESS PANEL

20¹⁄₁₆

(510)

OUTSIDE AIR

SHUTTER

A - 6 (152) DIA. FLUE OUTLET

B - 8 (203) DIA. FLUE COLLAR

Figure 15

Figure 16

FIREPLACE SPECIFICATIONS CONTINUED

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 17

FIREPLACE SPECIFICATIONS CONTINUED

Step 4. FIELD WIRING

Refer to Section A for millivolt appliances and

Section B for electronic appliances. The gas

valve is set in place and pre-wired at the

factory on both models.

A. Millivolt Wiring

(See Figure 18 )

–

1. Appliance-mounted ON/OFF burner control

switch (rocker switch) is factory installed in

the modesty panel. Optional wall-mounted

switch, thermostat, or one of the optional

remote control kits may also be used.

2. If wall-mounted ON/OFF control or thermo-

stat is selected, mount it in a convenient

location on a wall near the fireplace.

Figure 18

Thermopile

White

Black

Millivolt Wiring Diagram

If any of the original wire as supplied must be replaced,

it must be replaced with Type AWM 105°C – 18 GA. wire.

*OPTIONAL WALL-MOUNTED ON/OFF

SWITCH OR OPTIONAL THERMOSTAT

OR OPTIONAL REMOTE RECEIVER

*Turn the appliance-mounted ON/OFF burner control

switch to the OFF position if an optional

control switch is installed.

Factory Wired

Field Wired

Schematic Representation Only

APPLIANCE-MOUNTED ON/OFF SWITCH

LIMIT SWITCH

3. Wire the control switch within the millivolt

control circuit using the 15 feet of 2 con-

ductor wire supplied with the unit.

Note: The supplied 15 feet of 2 conductor

wire has one end of each conductor con-

nected to the gas valve circuit and the other

end of each conductor placed loose inside

the lower compartment of the unit.

Caution: do not connect the optional wall

switch to a 120V power supply.

4. If an optional control switch is installed,

turn the appliance-mounted ON/OFF burner

control switch to the OFF position.

EBBAY (Bay)

12 (305)

20¹⁄₁₆

(510)

TOP VIEW

40¹⁄₈

(1019)

FRAMING SPACERS

(Top and Side)

FINISH WALL BRACKET

(Front, back, and left edge of unit top)

7¹⁄₄

(184)

12¹⁄₂

(317)

(70)

BACK VIEW

LEFT SIDE VIEW

(RIGHT SIDE OPPOSITE)

3 (76)

2³⁄₄

5³⁄₄

(146)

OUTSIDE AIR

SHUTTER

A - 6 (152) DIA. FLUE OUTLET

B - 8 (203) DIA. FLUE COLLAR

(13)

DETAIL OF

FINISH WALL

BRACKET

¹⁄₂

(610)

(1041)

(940)

¹⁄₂

(13)

FRONT VIEW

4 (102)

GAS INLET

ELECTRICAL

INLETS

CONTROL COMPARTMENT

ACCESS PANEL

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Note: The gas valve ON/OFF switch is shown in

Figure 20 on page 11. It is integral with the gas

valve and should be set to the ON position.

B. Electronic Wiring

(also see figure 20 on page 11 )

Note: The electronic appliance must be con-

nected to the main power supply.

1. Route a 3-wire 120Vac 60Hz 1ph power

supply to the appliance junction box.

2. Open the control compartment access

panel, by actuating the spring-loaded

magnetic catches securing the panel,

gently depressing the outer top corners

of the panel until the catches "pop" the

panel free and allowing it to swing out

and down to open.

3. Remove the bottom control compartment

access panel by compressing the spring-

loaded hinge pin on the left side until it

disengages from the left cabinet panel

hole. Pull the panel away from the fire-

place.

See Figure 22 on page 12.

4. Remove the modesty panel by pulling the

bottom right corner of the modesty panel

out slightly to disengage the snap-fit fea-

ture; lift the modesty panel by the tab on

the panel's right end, pull the right end of

the panel away from the cabinet and then

pull the panel diagonally out of the left

side cabinet panel slots. (In the above

procedure, reverse the words "left" and

"right" for EBCR-2 models). Remove the

modesty panel carefully, so that none of

the wires become loose or disconnected.

5. Remove the outlet receptacle by removing

the two securing screws. See

Figure 19.

(The left and right designations used here

are reversed in EBCR-2 applications.)

6. Install a field-provided strain relief in the

cabinet knockout opening for the protec-

tion of the power supply wires.

7. Connect the power supply wires to the

receptacle as shown in

Figure 20 on

page 11.

8. Connect the ground supply wire and the

green wire attached to the outlet

receptacle's green ground screw.

9. Appliance-mounted ON/OFF burner con-

trol switch (rocker switch) is factory in-

stalled in the modesty panel. Optional

wall-mounted switch, thermostat, or one

of the optional remote control kits may

also be used.

10. If wall-mounted ON/OFF switch or thermo-

stat is to be used, mount it in a convenient

location on a wall near the fireplace.

11. If the wall-mounted ON/OFF switch is to be

used, wire it to the the low voltage circuit

as shown in

Figure 20 on page 11.

Note: The supplied 15 feet of 2 conductor wire

has one end of each conductor connected to

the gas valve circuit and the other end of each

conductor placed loose inside the lower com-

partment of the unit.

12. After wiring is complete, reinstall the out-

let receptacle; install the field-provided

the metal junction box cover plate; rein-

stall the modesty panel.

OUTLET RECEPTACLE INSTALLATION

Figure 19

IMPORTANT: Ground supply wire must be

connected to the green wire attached to

the outlet receptacle's green ground screw.

See

Figure 20 on page 11

. Failure to do so

will result in a potential safety hazard. The

appliance must be electrically grounded

in accordance with local codes or, in the

absence of local codes, the National Elec-

trical Code, ANSI/NFPA 70-(latest edition).

(In Canada, the current CSA C22-1 Cana-

dian Electrical Code.)

EBST-2, EBPF-2

AND EBCL-2 OUTLET RECEPTACLE SHOWN.

EBCR-2 HAS THE OUTLET RECEPTACLE LOCATED IN

THE LEFT CORNER OF THE UNIT

EBBAY OUTLET RECEPTACLE LOCATED IN

THE REAR LEFT CORNER OF THE UNIT

VIEW OF RIGHT BOTTOM CORNER OF UNIT

OUTLET RECEPTACLE

JUNCTION BOX

OUTLET RECEPTACLE

BOX SECURING SCREW

CABINET

RIGHT SIDE

PANEL

FIREBOX BOTTOM

Step 5. CONNECTING GAS LINE

Make gas line connections. All codes require a

shut-off valve mounted in the supply line.

Figure 21 on page 12

illustrates two methods

for connecting the gas supply. The flex-line

method is acceptable in the U.S., however,

Canadian requirements vary depending on lo-

cality. Installation must be in compliance with

local codes.

Figure 20

1. If any of the original wire as supplied must be replaced,

1. it must be replaced with Type AWM 105°C – 18 GA.

wire.

2. 120V, 60Hz – Less than 3 amps.

Junction Box

Transf.

120 V.

24 V

Factory Wired Field Wired

Electronic Wiring Diagram (Honeywell)

120

VAC.

Gas Valve

APPLIANCE-MOUNTED ON/OFF SWITCH

IGNITER

PILOT

ASSEMBLY

Outlet Box Green

Ground Screw

Hot side of Outlet

Schematic Representation Only

*ON/OFF Switch (Integral

with Gas Valve)

White Wire

To Opposite

Side

**OPTIONAL WALL SWITCH

OR OPTIONAL THERMOSTAT

OR OPTIONAL REMOTE

RECEIVER

*Leave the ON/OFF switch, which is integral

with the gas valve, in the ON position.

**Turn the appliance-mounted ON/OFF burner control switch to

the OFF position if an optional control switch is installed.

LIMIT SWITCH

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 22

Figure 21 -

GAS CONNECTION

These appliances are equipped with a gas flex

line for use (where permitted) in connecting the

unit to the gas line. A gas flex line is provided to

aid in attaching the B-vent appliance to the gas

supply. The gas flex line can only be used where

local codes permit. See

Figure 21

for flex line

description. The flex line is rated for both natu-

ral and propane gas. A manual shut off valve is

also provided with the flex line.

The gas control valve is located in the lower

control compartment. To access the valve

proceed as follows:

1- Open the control compartment access panel,

(Figure 22)

by actuating the spring-loaded

magnetic catches securing the panel, gently

depressing the outer top corners of the panel

until the catches "pop" the panel free and

allowing it to swing out and down to open.

2- Remove the bottom control compartment

access panel by compressing the spring-

loaded hinge pin on the left side until it

disengages from the left cabinet panel hole.

Pull the panel away from the fireplace.

See

Figure 22.

3- Remove the modesty panel by pulling the

bottom right corner of the modesty panel

out slightly to disengage the snap-fit fea-

ture; lift the modesty panel by the tab on

the panel's right end, pull the right end of

the panel away from the cabinet and then

pull the panel diagonally out of the left side

cabinet panel slots. (In the above proce-

dure, reverse the words "left" and "right"

for EBCR-2 models). Remove the mod-

esty panel carefully, so that none of the

wires become loose or disconnected.

Secure all joints tightly using appropriate

tools and sealing compounds (ensure pro-

pane resistant compounds are used in pro-

pane applications).

Step 6. Outside Air Kits – Optional outside make-

up air kits, Model FOAK-4 or FAOK-4LD, may be

used with these appliances. Refer to the installa-

tion instructions packaged with the air kits for

specific installation information. If used, the out-

side air kit must be installed before the fireplace is

framed and enclosed in the finished wall.

Outside air drawn into the fireplace supplies

air to the fire for combustion. Only one outside

air duct is necessary, if installed. See the

Figures on pages 8, 9 and 10

for the location

of the units outside air inlet.

If additional length of duct is necessary, pur-

chase locally available U.L. Class 0 or Class 1

metallic ducting. The duct may extend up to 50'

(15.24 m) in any direction.

Note: When installing the air duct vertically,

DO NOT terminate the duct closer than 3'

below the chimney top.

Outside combustion air ducting may be run

upwards or vertically through framing and

ceiling joists, with the hood installed through

an outside wall and 3' (1 m) below the termi-

nation. Ducting may also be run downward

through floor Joists and under the home to a

ventilated crawlspace not considered part of

the living area of the home.

Note: Do not terminate outside air kit in attic

space under any circumstances.

The millivolt control valve has a ³⁄₈"

(10 mm) NPT thread inlet port. The electronic

control valve has a ¹⁄₂" (13 mm) NPT thread inlet

port and is fitted with a ¹⁄₂" x ³⁄₈" (13 mm x

10 mm) NPT fitting.

Turn on gas supply and test for gas leaks using

a soapy water solution. Never use an open

flame to check for leaks.

A. Mix a 50% dish soap, 50% water solution.

B. Light the appliance (refer to the lighting

instructions provided in the Homeowner's Care

and Operation Instructions).

C. Brush all joints and connections with the

soapy water solution to check for leaks. If

bubbles are formed, or gas odor is detected,

turn the gas control knob to the “OFF” posi-

tion. Either tighten or refasten the leaking

connection and retest as described above.

D. When the gas lines are tested and leak free,

observe the individual tongues of flame on the

burner. Make sure all ports are open and

producing flame evenly across the burner. If

any ports are blocked, or partially blocked,

clean out the ports.

CAUTION: NEVER LOCATE INLET WHERE IT

CAN BE BLOCKED BY SHRUBS, SNOW

DRIFTS, ETC. NEVER LOCATE INLET IN GA-

RAGE OR ANY AREA WHERE THERE IS AN-

OTHER FUEL BURNING APPLIANCE OR PROD-

UCTS EMITTING COMBUSTIBLE GASES SUCH

AS PAINT, GASOLINE, ETC. IN COLD CLI-

MATES, IT IS RECOMMENDED THE COMBUS-

TION AIR DUCT BE INSULATED.

The hand operated outside air control lever is

located on the right side (EBST-2, EBPF-2, and

EBCL-2) or left side (ECBCR-2) of the fire-

place opening.

See Figure 23 on page 13.

To open the outside air shutter, open the bottom

control access panel, reach into the gap between

the firebox bottom and the modesty panel, and

pull the outside air control lever all the way out.

After completing the installation of the op-

tional outside air vent system, the outside air

control lever must be put in service and tested

to ensure proper operation before completing

any enclosure around the firebox. Failure to

do so may result in extensive and costly re-

work. Before the operation of the vent system

can be tested, the lever securing screw must

be removed.

See Figure 23 on page 13.

Gas Stub

¹₂" x

³₈" Flare

Shut-Off Valve

³₈ Flex Tubing

³₈" NPT ₂ ³₈

Flare Fitting

³₈" Nipple

³₈"

Union

³₈" Close Nipple

³₈" Shut-Off Valve

¹₂

³₈

Reducer

Gas

Valve

Gas Flex Line Connector

Piezo Ignitor

Gas Valve

Modesty Panel

Control

Compartment

Access panel

ON/OFF

Switch

Hinge

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 26

- Installing the Glass Enclosure Panel

Glass

Enclosure

Panel

Latch

Lower Compartment Door and Hinge

Front Glass

Enclosure Panel

Firebox Floor

Bottom Vee-flange

(Glass Enclosure

Panel Frame)

Top Flange

(Glass Enclosure

Panel Frame)

Modesty Panel

EBST-2 SHOWN

WARNING: NEVER OPERATE THE APPLI-

ANCE WITHOUT THE FRONT GLASS EN-

CLOSURE PANEL IN PLACE AND SECURE.

WARNING: HANDLE THE GLASS WITH EXTREME

CARE! TEMPERED GLASS IS SUSCEPTIBLE TO

DAMAGE (SCRATCHES, FOR EXAMPLE) –

HANDLE GLASS DOOR (GLASS ENCLOSURE

PANEL) GENTLY WHILE REINSTALLING IT.

Figure 24

Figure 25

The top ³⁄₈" (10 mm) at the pilot generator

(thermopile) and the top ¹⁄₈" min (tip) of the

quick drop out thermocouple should be en-

gulfed in the pilot flame. The flame should

project 1" (25 mm) beyond the hood at all three

ports

(Figure 24)

Millivolt Appliance Checkout

The pilot flame should be steady and, not lifting

or floating. Flame should be blue in color with

traces of orange at the outer edge.

Step 7. INSTALLING LOGS, VERMICULITE,

DECORATIVE VOLCANIC STONE AND

GLOWING EMBERS

The log set, with one plastic bag of vermicu-

lite, is packaged in a carton located within the

firebox. One plastic bag of glowing embers

and one plastic bag of decorative volcanic

stone is located in the bottom compartment.

Refer to the Homeowner's Care and Operat-

ing Instructions for detailed placement in-

structions for the log set, vermiculite, decora-

tive volcanic stone and glowing embers.

Step 8. CHECKING APPLIANCE OPERATION

With gas line installed run initial system check-

out before closing up the front of the unit.

Follow the pilot lighting instructions provided

in the Homeowner's Care and Operation In-

structions. For piezo ignitor location see

Figure

22 on page 12

(millivolt appliances only).

Note: Lighting instructions may also be found

on the pull out lighting instruction labels

attached to the gas control valve.

Step 9. INSTALLING GLASS ENCLOSURE

PANELS

Electronic Appliance Checkout

To light the burner, turn ‘ON’ the modesty

panel mounted ON/OFF switch and turn the gas

control switch to the “ON” position. Ensure the

ignitor lights the pilot. The pilot flame should

engulf the flame rod as shown in

Figure 25

Replace logs after pilot inspection.

To light the burner; turn “ON” the modesty

panel mounted ON/OFF switch and rotate the

gas valve control knob counterclockwise to

the “ON” position.

When first lighting the appliance, it will take

a few minutes for the line to purge itself of

air. Once purging is complete, the pilot and

burner will light and operate as indicated in

the instruction manual. Subsequent lightings

of the appliance will not require such purg-

ing. Inspect the pilot flame (remove logs, if

necessary, handling carefully).

1. Visually inspect the gasket on the backside

of the panels. The gasket surface must be

clean, free of irregularities and seated firmly.

2. Position the glass enclosure panel in front

of the firebox opening at a 45 degree angle and

engage the top flange over the lip at the top of

the firebox opening.

See Figure 26.

3. Swing the glass enclosure panel down and

back. Ensure the gasket seats evenly as the

panel draws shut. Engage the Vee-flange at

the bottom of the panel with the latch; then

close the latch to secure the panel.

4. After installing the front glass enclosure

panel, reinstall the modesty panel by inserting

the tongues on the left side of it into the slots on

the left side cabinet panel. Swing the right side

of the modesty panel towards the unit. Engage

the hook on the right side of the modesty panel

with the right side cabinet panel slot. Gently

press the bottom right corner of the modesty

panel to engage the snap-fit feature.

(The left and right designations used here

are reversed in EDCR-2 applications.)

5. After reinstalling the modesty panel, reinstall

the bottom control compartment access panel

by inserting the right side locating pin into the

right side cabinet panel and then the left side

spring-loaded pin into the left side cabinet panel.

Figure 23

Operate the actuator through several cycles

including the closed position. Ensuring proper

operation and freedom of movement. Return

the actuator arm to the closed position.

Outside Air Control Lever

and Securing Screw Location

(EBST-2, EBPF-2 and EBCR-2 Units Shown)

The outside air shutter should be fully open when

the fireplace is in use and completely closed

when the fireplace is not being used. Closing it

when not in use will prevent outside cold air from

entering the dwelling.

To access the label, see the procedure on the

previous page described for accessing the gas

control valve.

MILLIVOLT

Thermocouple

Hood

Ignitor Rod

³⁄₈" Min

(9 mm)

Thermopile

Pilot

Nozzels

ELECTRONIC

Proper Flame

Adjustment

Pilot

Nozzle

3/8 To 1/2 Inch

(9 mm to 13 mm)

Ground

Electrode

Flame Rod

Hot Surface

Igniter

Outside Air Control Lever with Stop Behind

Securing Screw

Outside Air Shutter in the

Closed Position

Control Compartment Access Panel

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

RENRUBNIAM

GNITTESRETTUHSYROTCAF

sledoM

saGlarutaN

sehcni

)mm(

enaporP

saG

sehcni

)mm(

2-TSBE

2-FPBE

2-RCBE

2-LCBE

YABBE

61/1)5.1(61/5)8(

Figure 27

Figure 28

*Note - Do Not Adjust the Factory-Set Position.

Each of the two air shutters (one for each

burner) are open the amount shown in

the table, below.

Orifice

*Air Shutter

Opening

Burner

Venturi

Tube

Step 10. BURNER ADJUSTMENTS

Note -

The air shutter for the burner primary air

opening is factory-set. Do not adjust the factory-

set position. The factory-set position is shown in

Figure 27.

Step 11. Spillage Test and Safety Limit

Switch Operation

Spillage Test

After appliance installation, perform this spillage

test to verify that proper venting conditions exist:

1 - Place unit in its normally-operated con-

dition, that is, with the glass enclosure pan-

els in place.

2 - Close all doors and windows in the

room. Turn on all exhaust fans in the house.

3 - Light the appliance.

4 - Wait 15 minutes.

5 - To check for venting action, start by

holding a smoke producing device within an

inch of one edge (side edge, not top or

bottom edge) of one glass enclosure panel.

The smoke should be drawn toward the edge

of the glass enclosure panel. Continue the

test by moving the smoke producing device

along the entire length of both side-edges of

the glass door. Repeat the test for all glass

enclosure panels.

6 - If the smoke is not drawn towards the

edges of the glass door turn off the appli-

ance and call a qualified service technican.

Manually-Reset Safety Limit Switch

This appliance is equipped with a manually-reset blocked flue safety limit switch. Refer to

Figure 28

for its location. If, during appliance operation, the flame goes out (independently of the burner on/

off wall switch), it may be due to the operation of this safety limit switch. First allow the appliance

to cool, then reset the safety switch by pushing the red reset button on the back of the switch.

To access the blocked flue safety limit switch

refer to

Figure 28:

A - To access the blocked flue safety switch when top radiant panel is not covered with non-

combustible material:

1 - Lift up and remove top radiant panel/eyebrow assembly on the control side of unit.

2 - Reach between the cabinet side and the firebox side wall and locate the blocked flue safety

switch.

3 - Push the red reset button on the switch.

The applilance should then relight and remain lit. If this does not occur, turn off the appliance and

call a qualified service technician.

B - To access the blocked flue safety switch when top radiant panel is covered with non-

combustible material:

NOTE - This procedure should only be performed by a qualified service technician.

Important - Turn electrical power off before beginning this procedure.

1 - Lower bottom hinged panel on the control side of the fireplace. Remove the modesty panel

and glass enclosure panel as described on page 5, Steps 3, 4, 5 and 6 under "Detailed Installation

Steps" heading.

2 - Remove the side baffle securing screws (5) and then remove the baffle.

3 - Remove the safety switch bracket securing screws (2), and pull the switch/bracket assembly

through the side panel slot.

4 - Push the red reset button on the switch.

5 - Reinstall the switch/bracket assembly.

6 - Reinstall the side baffle.

7 - Reinstall front glass door.

8 - Raise the bottom hinged panel.

The appliance should then relight and remain lit. If this does not occur, check unit for a blocked

flue condition.

SAFETY SWITCH LOCATION (EBCL-2 SHOWN) EBST-2 and EBPF-2 Safety Switch Location Also as Shown;

EBCR-2 Location on the Left End of the Fireplace, EBBAY Location on the Rear of the Fireplace.

MANUALLY-RESET

SAFETY LIMIT SWITCH

FIREBOX SIDE BAFFLE

FIREBOX SIDE BAFFLE SECURING SCREW

FIREBOX

SIDE WALL

CABINET

SIDE WALL

TOP RADIANT PANEL

AND EYEBROW

BRACKET

SECURING SCREW

SAFETY SWITCH

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

12 (305) MANTEL

10 (254) MANTEL

8 (203) MANTEL

6 (152) MANTEL

4 (102) MANTEL

(102)

(356)

(305)

(254)

2 (51) MANTEL

TOP OF

APPLIANCE

(152)

NOTE - Hood shown as positioned

in louvered front model. The hood

position in the flush faced front model

is lower than shown.

(203)

MANTEL CLEARANCES

Inches (mm)

*Note - The side walls of mantels may protrude

beyond the front face of the fireplace a maximum

of 5 inches (127mm) at 0 inch clearance to the

sides of the fireplace.

Figure 29

COLD CLIMATE INSULATION

If you live in a cold climate, seal all cracks

around your appliance with noncombustible

material and wherever cold air could enter the

room. It is especially important to insulate

outside chase cavity between studs and under

floor on which appliance rests, if floor is above

ground level.

A hearth extension is not required with this appliance. If a hearth extension is used, do not block the

control compartment access panel. Any hearth extension used is for appearance only and does not

have to conform to standard hearth extension installation requirements.

Note: Combustible wall finish materials and/or surround materials must not be allowed to

encroach the area defined by the appliance front face (black sheet metal). Never allow

combustible materials to be positioned in front of or overlapping the appliance front face. See

Figures 30.

Non-combustible materials, such as surrounds and other appliance trim, may be installed on the appliance

front face with these exceptions: they must not cover any portion of the glass or louvers; they must not cover

any portion of the top radiant panel and the air gaps surrounding the top radiant panel.

Vertical installation clearances to combustible mantels vary according to the depth of the mantel.

(See Figure 29)

. Mantels constructed of non-combustible materials may be installed at any height

above the appliance opening; however, do not allow anything to hang below the hood.

Figure 30

FINISHING REQUIREMENTS

Wall Details

Complete finished interior wall. To install the appliance facing flush with the finished wall, position

framework to accommodate the thickness of the finished wall (

Figures 30

Step 12. HOOD INSTALLATION

All of these appliances must have hoods installed prior to operating on all sides with glass

enclosure panels.

On all clean face units, slide the hoods into the slots on the lower edges of the radiant panels (

Figure 30

Combustible

Finished Wall

Materials May

Touch Top of

Unit

This Area Must Remain Clear

of Combustible Materials

Top of Appliance

1" Min

(25 mm)

Combustible

Wall Framing

Spacer

Clean Face Models

Top of Door Frame

Hood must be installed as shown.

Radiant panel

Combustible Wall

Framing

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

tiKnoisrevnoCsaGenaporPoTlarutaN

.oNsledoMepyTtinU.oNgolataC

2-TSBE

2-FPBE

YABBE

tlovillim56L58

cinortcele97L58

tiKnoisrevnoCsaGenaporPoTlarutaN

.oNsledoMepyTtinU.oNgolataC

2-RCBE

2-LCBE

tlovillim24M91

cinortcele44M91

tiKnoisrevnoCsaGlarutaNotenaporP

.oNledoMepyTtinU.oNgolataC

2-TSBE

2-FPBE

YABBE

tlovillim27L58

cinortcele68L58

tiKnoisrevnoCsaGlarutaNotenaporP

.oNledoMepyTtinU.oNgolataC

2-RCBE

2-LCBE

tlovillim34M91

cinortcele54M91

GAS CONVERSION KITS

In Canada:

THE CONVERSION SHALL BE CARRIED OUT

IN ACCORDANCE WITH THE REQUIREMENTS

OF THE PROVINCIAL AUTHORITIES HAVING

JURISDICTION AND IN ACCORDANCE WITH

THE REQUIREMENTS OF THE CAN1-B149.1

AND .2 INSTALLATION CODE.

LA CONVERSION DEVRA ÊTRE EFFECTUÉE

CONFORMÉMENT AUX RECOMMANDATIONS

DES AUTORITÉS PROVINCIALES AYANT

JURIDICTION ET CONFORMÉMENT AUX

EXIGENCES DU CODE D'INSTALLATION CAN1-

B149.1 ET.2.

Gas conversion kits are available to convert

your appliance from the use of one type of gas

to the use of another. These kits contain all the

necessary components needed to complete

the task including labeling that must be affixed

to ensure safe operation.

Kit part numbers are listed here and the follow-

ing steps detail the conversion procedure.

WARNING: THIS CONVERSION KIT SHALL BE

INSTALLED BY A QUALIFIED SERVICE AGENCY IN

ACCORDANCE WITH THE MANUFACTURER'S IN-

STRUCTIONS AND ALL APPLICABLE CODES AND

REQUIREMENTS OF THE AUTHORIZED AGENCY

HAVING JURISDICTION. IF THE INFORMATION IN

THESE INSTRUCTIONS IS NOT FOLLOWED EX-

ACTLY, A FIRE, EXPLOSION OR PRODUCTION OF

CARBON MONOXIDE MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY OR LOSS

OF LIFE. THE INSTALLATION IS NOT PROPER AND

COMPLETE UNTIL THE OPERATION OF THE CON-

VERTED APPLIANCE IS CHECKED AS SPECIFIED IN

THE OWNER INSTRUCTIONS SUPPLIED WITH THE

KIT. THE QUALIFIED SERVICE AGENCY PERFORM-

ING THIS INSTALLATION ASSUMES RESPONSI-

BILITY FOR THIS CONVERSION.

AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION

SERA INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE SER-

VICE CONFORMÉMENT AUX INSTRUCTIONS DU

FABRICANT ET TOUTES EXIGENCES ET CODES

APPLICABLES DE L'AUTORISÉS AVOIR LA JURIDICTION.

SI L'INFORMATION DANS CETTE INSTRUCTION N'EST

PAS SUIVIE EXACTEMENT, UN FEU, EXPLOSION OU PRO-

DUCTION DE PROTOXYDE DE CARBONE PEUT RÉSULTER

LE DOMMAGES CAUSER DE PROPRIÉTÉ, PERTE OU

BLESSURE PERSONNELLE DE VIE. L'AGENCE QUALIFIÉE

DE SERVICE EST ESPONSABLE DE L'INSTALLATION

PROPRE DE CET ÉQUIPMENT. L'INSTALLATION N'EST

PAS PROPRE ET COMPLÉTE JUSQU'À L'OPÉRATION DE

L'APPAREIL CONVERTI EST CHÉQUE SUIVANT LES

CRITÈRES ÉTABLIS DANS LES INSTRUCTIONS DE

PROPRIÉTAIRE PROVISIONNÉES AVEC L'ÉQUIPEMENT.

b. Remove the bottom control compartment

access panel by compressing the spring-

loaded hinge pin on the left side until it

disengages from the left cabinet panel

hole. Pull the panel away from the fire-

place.

See Figure 22 on page 12.

c. Remove the modesty panel by pulling the

bottom right corner of the modesty panel

out slightly to disengage the snap-fit fea-

ture; lift the modesty panel by the tab on

the panel's right end, pull the right end of

the panel away from the cabinet and then

pull the panel diagonally out of the left side

cabinet panel slots. (In the above proce-

dure, reverse the words "left" and "right"

for EBCR-2 models). Remove the mod-

esty panel carefully, so that none of the

wires become loose or disconnected.

d. Locate the latch at the top of the control

compartment. To disengage the latch from

the bottom vee-flange of the glass enclo-

sure panel, reach for the handles located

towards the back of the latch and pull the

handl down toward the front of the unit.

e. Swing the bottom of the door out and raise

it slightly to lift the top flange of the door

frame away from the appliance.

Step 2. Carefully remove the logs. Exercise

care as not to break the logs.

Step 3. Referring to

Figure 31 on page 17

remove the two burners.

Step 1. Turn off the gas supply to the appliance.

a. Open the control compartment access panel,

by actuating the spring-loaded magnetic

catches securing the panel, gently depress-

ing the outer top corners of the panel until the

catches "pop" the panel free and allowing it to

swing out and down to open.

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

FRONT OF FIREPLACE

REAR BURNER

FRONT BURNER

FIREBOX SUBFLOOR

BURNER POSITIONING

REAR BURNER

FRONT BURNER

PILOT

BURNER

Note: The burners are not identical. Position them so

that the circular burner ports run as shown. Note

especially the vertical run of ports relative to the pilot

burner. Bracket A on the rear burner will interfere

with the pilot burner if an attempt is made to install

the rear burner in the front burner’s position.

BRACKET A

BURNER

PORTS

NOTE: INSTALL REAR BURNER FIRST,

THEN FRONT BURNER.

Pressure

Regulator

Remove

These

Components

Pilot

Orifice

Spring

Adjusting

Screw

Slotted

Cap

OFF

CONTROL

Manifold

Pressure

Test Port

Inlet Pressure Test Port

Retaining

Clip

Ignitor

Assembly

Pilot

Assembly

Pilot

Orifice

Flare Nut

Figure 35

Figure 34

Figure 33

Figure 32

Figure 31

When reinstalling the ignitor assembly, use

extreme care to prevent damage and break-

age. Do not apply any leverage to the ignitor

assembly while restoring the retainer clip to

its original position.

Note: If the ignitor is damaged, a replace-

ment kit is available, order Catalog Number

87L54.

Electronic Appliances

Step 7. Honeywell Electronic Valves - See

Figure 34

and the instructions provided with

the kit. Remove the slotted cap screw, o-ring,

pressure-regulating adjusting screw and

spring. Retain all parts for possible later use.

Install new components from the kit. Black

cap and red spring for propane gas units.

Silver cap and stainless steel spring fro natural

gas units. Before installing the cap, attach

manometer to the manifold side pressure test

fitting and adjust screw until pressure reads

3.5 inches water column (0.87 kPa) for natural

gas, and 10.0 inches water column (2.49 kPa)

for propane gas.

See

Figure 35

and replace the pilot orifice as

follows: Remove the ignitor assembly retainer

clip, and carefully remove the ignitor assembly.

Exercise extreme care to prevent damage to

or breakage of the ignitor assembly. Remove

the screw securing the pilot assembly to its

mounting bracket. Back off the flare nut at the

end of the pilot gas line to free the pilot assem-

bly from the gas line. Remove the pilot orifice

and replace it with the one provided with the

conversion kit. Reinstall the pilot assembly by

reversing the steps detailed here.

Step 5. Attach manometer to the manifold side

pressure test fitting and verify manifold pres-

sure reads 3.5 inches water column (0.87 kPa)

for natural gas, and 10.0 inches water column

(2.49 kPa) for propane gas.

Step 6. Refer to

Figure 33

and remove the

pilot hood assembly to access the hexed pilot

orifice. Remove and replace the orifice with

the one provided with the kit.

Millivolt Appliances

Step 4. SIT Systems - Refer to

Figure 32

and

the instructions provided with the kit. Using a

Torx T20, remove and discard the three pres-

sure regulator mounting screws. Remove the

pressure regulator, spring, poppet, diaphragm

and bushing. Discard all removed compo-

nents. Ensure the rubber gasket installed on

the back of the replacement pressure regulator

is properly positioned and install the new pres-

sure regulator using the new screws supplied

with the kit. Tighten screws to 25 In. lb. torque.

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 36

Step 9. Reassemble the remaining compo-

nents by reversing the procedures outlined in

the preceding steps. Use pipe joint compound

or Teflon tape on all pipe fittings before install-

ing (ensure propane resistant compounds are

used in propane applications, do not use pipe

joint compounds on flare fittings).

Step 10. Attach the conversion label provided

in the conversion kit to the rating plate on the

appliance.

Figure 37

shows all of the labels for

all of the kits covered by this manual as shown

in the tables on page 17. Compare the label

provided in the kit being installed to the appro-

priate label shown in

Figure 37

Step 11. Turn on the gas suply and test for

leaks as shown in

step 5 on page 11

* Each model has two burners. Each burner contains one

of these orifices.

Figure 37

THIS APPLIANCE HAS BEEN CONVERTED TO:

NATURAL GAS

Models: EDST-2,EDPF-2,EBBAY

INPUT BTU/HR – 37,500

MANIFOLD PRESSURE – 3.5"

ORIFICE SIZE – #44

Kit Catalog No.

85L72 and 85L86

Kit Catalog No.

85L65 and 85L79

THIS APPLIANCE HAS BEEN CONVERTED TO:

PROPANE/LPG

Models: EDST-2,EDPF-2,EBBAY

INPUT BTU/HR – 37,500

MANIFOLD PRESSURE – 10.0"

ORIFICE SIZE – #55

THIS APPLIANCE HAS BEEN CONVERTED TO:

NATURAL GAS

Models: EDCR-2,EDCL-2

INPUT BTU/HR – 34,000

MANIFOLD PRESSURE – 3.5"

ORIFICE SIZE – #47

Kit Catalog No.

19M43 and 19M45

Kit Catalog No.

19M42 and 19M44

THIS APPLIANCE HAS BEEN CONVERTED TO:

PROPANE/LPG

Models: EDCR-2,EDCL-2

INPUT BTU/HR – 34,000

MANIFOLD PRESSURE – 10.0"

ORIFICE SIZE – 0.050 INCH

ledoM

.oN

*ezisecifirO

noitavelE

teeF

)sretem(

.taN.porP

2-TSBE

2-FPBE

YABBE

44#55#

0054-0

)2731-0(

2-RCBE

2-LCBE

74#"05.0

All Models

Step 8.

(Refer to Figure 31)

A. Remove the orifice from the manifold

and replace it with the one provided in the

kit. See the following table for orifice

sizes for natural and propane models

Figure 36

illustrates the orifice.

B. Install the burners as shown in

Figure 31

The primary air opening can be adjusted by

removing the venturi tube air shutter se-

curing screw and placing it in the other hole

provided nearby. The correct hole usage

for this screw for the gas being used can be

determined by the air shutter gap indicated

Figure 27 on page 14.

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

f i r e - p a r t s . c o m

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

P/N 850,008M REV. H 05/2004

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,

materials, specifications, prices and also to discontinue colors, styles and products.

Consult your local distributor for fireplace code information.

1110 West Taft Avenue • Orange, CA 92865

f i r e - p a r t s . c o m

Lennox Elite EBBAYNE Installation Instructions Manual

Marque: Lennox

Modèle: Elite EBBAYNE

Catégorie: Cheminées

Taper: Installation Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Lennox Elite EBBAYNE

Lennox Elite EBBAYNE Installation Instructions Manual

Lennox Elite EBBAYNE Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents