Skil RH1704-1A Le manuel du propriétaire

Marque: Skil

Modèle: RH1704-1A

Catégorie: Perceuses électriques

Taper: Le manuel du propriétaire

1-877-SKIL-999

www.skil.com

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

20V Brushless Rotary Hammer

Perceuse à percussion sans balai de 20 V

Taladro percutor sin escobillas de 20 V

Model/ Modelo/ Modèle: RH170401

TABLE OF CONTENTS

General Power Tool Safety Warnings . ............................3-4

Safety Warnings for Hammer ......................................5

Symbols .....................................................6-9

Get to Know Your Rotary Hammer ................................10

Specications .................................................10

Operating Instructions .......................................11-17

Maintenance ...................................................18

Troubleshooting ...............................................18

Limited Warranty of SKIL Cordless Tool ............................19

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce

dust-related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles. A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained

power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs. Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied. Damaged or modied

batteries may exhibit unpredictable behaviour resulting in re, explosion or risk of injury.

Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or

temperature above 130 °C may cause explosion.

Follow all charging instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions. Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service of battery packs should only be performed

by the manufacturer or authorized service providers.

SAFETY WARNINGS FOR HAMMER

Wear ear protectors. Exposure to noise can cause hearing loss.

Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

Hold power tools by insulated gripping surfaces, when performing an operation where

the cutting accessory may contact hidden wiring or its own cord. Cutting accessory

contacting a ‘’live’’ wire may make exposed metal parts of the power tool ‘’live’’ and could give

the operator an electric shock.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner’s

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always

use eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II tool

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Symbol Name Designation/Explanation

Read manual symbol Alerts user to read manual

Wear eye protection symbol

Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

GET TO KNOW YOUR ROTARY HAMMER

20V Brushless Rotary Hammer

SDS Plus Drill Chuck

Mode Selector

Direction-of-Rotation

(forward/center-lock/

reverse) Selector

Variable-Speed

Trigger Switch

Handle Grip

Auxiliary

Handle

Quick

Clamp

Depth Rod

Fig. 1

SPECIFICATIONS

Rated voltage 20V d.c.

Chuck size/type SDS Plus

No-load speed 0 ~ 1400 /min

Recommended working temperature 14 ~ 104°F (-10 ~ 40°C)

Recommended storage temperature 32 ~ 104°F (0 ~ 40°C)

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due

to a short circuit, never immerse your tool, battery pack, or charger

in uid or allow a uid to ow inside them. Corrosive or conductive uids, such as seawa-

ter, certain industrial chemicals, and bleach or bleach-contain ng products, etc, can cause a

short circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced. Use of this product with damaged or missing

parts could result in serious personal injury.

WARNING

Do not attempt to modify this tool or create accessories not recom-

mended for use with this tool. Any such alteration or modication is

misuse and could result in a hazardous condition leading to possible serious injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when assem-

bling parts.

This cordless rotary hammer must be used only with the battery packs and chargers

listed below:

Battery Pack

Charger

2Ah 2Ah 2.5Ah 4Ah 5Ah

SKIL

BY519701

SKIL

BY519702

SKIL

BY519703

SKIL

BY519601

SKIL

BY519603

SKIL

SC535801

SKIL

QC536001

NOTICE: Please refer to the battery pack and charger manuals for detailed operating

information.

To Attach/Detach Battery Pack

(Fig. 2)

Lock the trigger switch “OFF” on the tool by

placing the direction-of-rotation (forward/

center-lock/reverse) selector in the center

position before attaching or detaching the

battery pack.

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves in the tool, and then slide the battery

pack onto the tool.

To detach the battery pack:

Depress the battery-release button, located

on the front of the battery pack, to release the

battery pack. Pull the battery pack out and

remove it from the tool.

NOTICE: When placing the battery pack on the tool, be sure that the raised rib on the battery

pack aligns with the groove inside the tool and that the latches snap into place properly.

Improper attachment of the battery pack can cause damage to internal components.

WARNING

Battery tools are always in operating condition. Therefore, the

direction-of-rotation (forward/center-lock/reverse) selector should

always be locked in the center position when the tool is not in use or when carrying it

at your side.

Fig. 2

Attach

Detach

Battery- Release Button

Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector

WARNING

After tool use, lock the direction-of-rotation selector in the “OFF”

position (center-lock) to help prevent accidental starts and possible

injury.

Your tool is equipped with a direction-of-rotation selector, located above the trigger switch.

This selector is designed for changing the direction of rotation of the bit and for locking the

trigger in the “OFF” (center-lock) position (Fig. 3).

a. Position the direction-of-rotation selector to the far left of the tool for forward rotation.

b. Position the direction-of-rotation selector to the far right of the tool for reverse rotation.

c. Position the switch in the “OFF” (center-lock) position to help to reduce the possibility of

accidental starting when not in use.

NOTICE: To prevent gear damage, always allow the rotary hammer to come to a complete

stop before changing the direction of rotation.

NOTICE: The rotary hammer will not operate unless the direction-of-rotation selector is

engaged fully to the left or right.

Fig. 3

Forward Center-Lock Reverse

Variable-Speed Trigger Switch

(Fig. 4)

Your tool is equipped with a variable-speed

trigger switch. The tool can be turned "ON"

by depressing the trigger switch or "OFF" by

releasing the trigger switch.

The variable-speed trigger switch delivers

higher speed with increased trigger pressure

and lower speed with decreased trigger

pressure.

Fig. 4

Mode Selector

The operation of the gearbox for each application is set with the mode selector. To change

among functions, slide and rotate the selector to the desired operating mode.

Rotary Drilling Mode

For drilling into steel, wood, and plastics, choose

the Rotary drilling position.

Hammer Drilling Mode

For simultaneous drilling and impacting of

concrete or masonry, choose the Hammer drilling

position.

Working Angle

Adjustment for Chisel Bits

To freely rotate the chisel bits to the desired angle

for hammering mode only, choose the position.

(The tool must not be operated when the switch

is in this position)

Hammering Mode

For hammering only - for light chipping, chiseling,

and demolition applications, choose the Hammer

position.

Working Angle Adjustment for

Chisel Bits

Choose a position which is best suited for your

operation. The position is intended for use with

chisel bits such as bull points, spades, gouges,

etc. Turn the mode selector to the

symbol

Next, rotate the locking sleeve, along with the

accessory, to the desired position. Then turn

the mode selector to the “hammer only” setting.

Then make sure that the chisel is securely held

in place by rotating it slightly (Fig. 5).

Fig. 5

Auxiliary Handle (Fig. 6)

The tool must be supported with the auxiliary

handle, which can be swiveled 360°.To reposi-

tion and/or swivel the handle, loosen the hand

grip, move the handle to the desired position

along the barrel and securely retighten the

hand grip.

WARNING

Always use the auxiliary

handle.

Depth Rod (Fig.7)

–

Depress the upper part of the quick clamp,

then insert the depth rod through the hole.

Make sure that the rippled part is facing

down.

–

Align the tip of the depth rod with the drill tip.

Now pull the depth rod back a length equal to

the required drilling depth.

–

Release the quick clamp to lock the depth

rod in position.

Install and Remove Accessories

(Fig. 8 & 9)

WARNING

Do not use bits with a

damaged shank.

Your tool is equipped with an SDS Plus chuck.

Lock the trigger switch “OFF” on the tool by

placing the direction-of-rotation selector in the

center position.

To install the accessory (Fig. 8):

For SDS+ accessories:

–

Clean the accessory and lightly lubricate it

before inserting it into the chuck.

–

Insert the accessory in the SDS+ chuck while

turning and pushing it until it engages; the

accessory locks in position automatically.

Fig. 7

Fig. 8

Fig. 6

Auxiliary Handle

Hand Grip

To remove the accessory (Fig. 9):

–

Pull back the locking sleeve and remove the

accessory from the chuck.

NOTICE: The SDS+ accessory requires

freedom of movement, which causes

eccentricity in the revolutions when the tool is

off-load; however, the accessory automatically

centers itself during operation without affecting

drilling precision.

WARNING

Use protective gloves

when removing the bit

from the tool, or rst allow the bit to cool

down. The bit may be hot after prolonged

use.

Drill Bits

Always inspect drill bits for excessive wear. Use only bits that are sharp and in good condition.

Twist Bits: Available with straight and reduced shanks for wood and light-duty metal drilling.

High-speed bits cut faster and last longer on hard materials.

Carbide-Tipped Bits: Used for drilling stone, concrete, plaster, cement, and other unusually

hard, nonmetal materials. Use continuous, heavy feed pressure when using carbide-tipped bits.

Drilling

WARNING

Always wear safety goggles or safety glasses with side shields

during power tool operation or when blowing dust. If the operation is

dusty, also wear a dust mask.

a. Check that the direction-of-rotation selector is at the correct setting (forward or reverse).

b. Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill

bit rotates.

c. Hold the drill rmly, and place the bit at the point to be drilled.

d. Depress the trigger switch to start the drill.

e. Move the drill bit into the workpiece, applying only enough pressure to keep the bit “biting”.

Do not force the drill or apply side pressure to elongate a hole. Let the tool do the work.

f. When drilling hard, smooth surfaces, use a center punch to mark the desired location of the

hole. This will prevent the drill bit from slipping off-center as the hole is started.

g. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will

prolong the life of the bit and increase the drilling action.

h. If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Remove the bit

from the workpiece and determine the reason for jamming.

NOTICE: There are two rules for drilling hard materials. First, the harder the material, the

greater the pressure you need to apply to the tool. Second, the harder the material, the slower

the speed should be. If the hole to be drilled is fairly large, drill a smaller hole rst, and then

enlarge to the required size with a larger bit; it’s often faster in the long run.

Fig. 9

Locking Sleeve

Drilling with non SDS Drill Bits (Fig. 10)

For drilling with non SDS drill bits in wood, metal, and plastic, use an adapter (not included).

a. Lock the trigger switch “OFF” on the tool by placing the direction-of-rotation selector in the

center position.

b. Clean and lightly lubricate the adapter before inserting it into the chuck.

c. Insert the adapter in the SDS+ chuck while turning and pushing the adapter until it engages;

the adapter locks in position automatically.

d. Pull the adapter to check that it is locked correctly.

e. Set the mode selector to normal drilling when using with the adapter.

Fig. 10

Chuck Adapter

(not included)

Wood Drilling

(Rotary Drilling Mode)

For maximum performance, use high-speed

steel or brad-point bits for wood drilling, and

set the mode selector to the rotary drilling

mode

a. Begin drilling at a very low speed to prevent

the bit from slipping off the starting point.

b. Increase speed as the drill bit bites into the

material.

c. When drilling “through” holes, place a block

of wood behind the workpiece to prevent

ragged or splintered edges on the back side

of the hole (Fig. 11).

NOTICE: Bits may overheat unless pulled out frequently to clear chips from utes.

Fig. 11

Metal Drilling (Rotary Drilling Mode)

For maximum performance, use high-speed steel bits for metal or steel drilling, and set the

mode selector to the rotary drilling mode

a. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will

prolong the life of the bit and increase the drilling action.

b. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.

c. Maintain a speed and a pressure that allow cutting without overheating the bit. Applying too

much pressure will:

–

Overheat the drill.

–

Wear the bearings.

–

Bend or burn bits.

–

Produce off-center or irregularly shaped holes.

Masonry Drilling (Hammer Drilling Mode)

For maximum performance, use carbide-tipped masonry bits when drilling holes in brick,

concrete, etc and set the mode selector to the hammer drilling mode

a. Maintain a speed and a pressure that allow cutting without overheating the bit or drill.

Applying too much pressure will:

–

Overheat the drill.

–

Wear the bearings.

–

Bend or burn bits.

–

Produce off-center or irregular-shaped holes.

b. Apply light pressure and medium speed for best results in brick.

c. Apply additional pressure for hard materials, such as concrete.

d. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.

Tile Drilling (Rotary Drilling Mode)

For maximum performance, use high-speed steel bits for drilling in tile, and set the mode

selector to the rotary drilling mode

a. When drilling holes in tile, practice on a scrap piece to determine the best speed and

pressure. Set the tool to rotary drilling mode.

b. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.

NOTICE: Fig.12 shows some tips for different drilling operations.

Fig. 12

Dust-free drilling in walls

Dust-free drilling in

ceilings

Drilling in tiles without

skidding

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components, which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air. Always

wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not

attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia, and household detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

TROUBLESHOOTING

Problem Cause Remedy

Tool will not start. 1. Battery pack is depleted.

2. Tool is over-loaded.

3. Battery pack is over-

temperature.

4. Battery pack is not installed

properly.

5. Burned out switch.

1. Charge the battery.

2. Release the trigger switch and try

again.

3. Turn off the tool and cool the

battery pack under air ow.

4. Conrm that the battery is locked

and secured to the tool.

5. Have the switch replaced by an

Authorized SKIL Service Center or

Service Station.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME

STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

02/19

TABLE DES MATIÈRES

Avertissements de sécurité généraux relatifs

aux outils électriques . .......................................21-23

Avertissements de sécurité relatifs à la perceuse à percussion ........23

Symboles ..................................................24-27

Apprenez à connaître votre perceuse à percussion ..................28

Caractéristiques techniques .....................................28

Mode d’emploi ..............................................29-37

Entretien ......................................................38

Dépannage ....................................................39

Garantie limitée des outils SKIL destinés à un usage résidentiel ....39-40

AVERTISSEMENT

•

La poussière créée pendant le ponçage mécanique, le sciage, le polissage, le perçage et

d’autres activités liées à la construction peut contenir des produits chimiques reconnus par

l’État de la Californie comme étant la cause de cancer, d’anomalies congénitales et d’autres

problèmes liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :

–

du plomb provenant de peintures à base de plomb;

–

de la silice cristalline provenant de la brique, du ciment ou d’autres matériaux de

maçonnerie;

–

de l’arsenic et du chrome provenant du bois d’œuvre traité avec un produit chimique.

•

Les risques liés à l’exposition à ces produits varient selon le nombre de fois où vous

pratiquez ces activités. Pour réduire votre exposition à ces produits chimiques :

–

travaillez dans un endroit bien ventilé;

–

munissez-vous de l’équipement de sécurité approuvé tel que des masques antipoussières

conçus spécialement pour ltrer les particules microscopiques;

–

évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage, le

polissage, le perçage et d’autres activités liées à la construction. Portez un équipement de

protection et lavez à l’eau et au savon toutes les parties exposées. Les poussières pénétrant

dans votre bouche ou dans vos yeux et les poussières se déposant sur votre peau peuvent

causer l’absorption de produits chimiques dangereux.

La page charge ...

Skil RH1704-1A Le manuel du propriétaire

Marque: Skil

Modèle: RH1704-1A

Catégorie: Perceuses électriques

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Skil RH1704-1A Owner's manual
español: Skil RH1704-1A El manual del propietario

Skil RH1704-1A Le manuel du propriétaire

Skil RH1704-1A Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents