BSS Audio BLU-806DA (BLU-806) Guide d'installation

Marque: BSS Audio

Modèle: BLU-806DA (BLU-806)

Catégorie: Équipement musical supplémentaire

Taper: Guide d'installation

Ce manuel convient également à

Soundweb

London

BLU-800/BLU-805/BLU-806/BLU-806DA/BLU-320/

BLU-325/BLU-326/BLU-326DA/BLU-160/BLU-120

Installation Guide

5086087-A

IMPORTANT SAFETY INSTRUCTIONS

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system

for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free

of charge to designated collection facilities or to a retailer (if you purchase a similar new one).

For Countries not mentioned above, please contact your local authorities for a correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent

potential negative effects on the environment and human health.

U.K. MAINS PLUG WARNING

A molded mains plug that has been cut off from the cord is

unsafe. Discard the mains plug at a suitable disposal facility.

NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU

INSERT A DAMAGED OR CUT MAINS PLUG INTO A

13 AMP POWER SOCKET.

Do not use the mains plug without the fuse cover in place.

Replacement fuse covers can be obtained from your local retailer.

Replacement fuses are 13 amps and MUST be ASTA approved to

BS1362.

The symbols shown above are internationally accepted symbols that warn

of potential hazards with electrical products. The lightning flash with

arrowpoint in an equilateral triangle means that there are dangerous

voltages present within the unit. The exclamation point in an equilateral

triangle indicates that it is necessary for the user to refer to the owner’s

manual.

These symbols warn that there are no user serviceable parts inside the

unit. Do not open the unit. Do not attempt to service the unit yourself.

Refer all servicing to qualified personnel. Opening the chassis for any

reason will void the manufacturer’s warranty. Do not get the unit wet. If

liquid is spilled on the unit, shut it off immediately and take it to a dealer

for service. Disconnect the unit during storms to prevent damage.

The following is indicative of low

altitude use; do not use this product

above 2000m.

WARNING FOR YOUR PROTECTION

READ THE FOLLOWING:

READ THESE INSTRUCTIONS.

KEEP THESE INSTRUCTIONS.

HEED ALL WARNINGS.

FOLLOW ALL INSTRUCTIONS.

DO NOT USE THIS APPARATUS NEAR WATER.

CLEAN ONLY WITH A DRY CLOTH.

FOR INDOOR USE ONLY.

DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE

MANUFACTURER’S INSTRUCTIONS.

DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR

OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.

ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.

UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS

OF TIME.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit

your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

Use only with the cart stand, tripod bracket, or table specified by the

manufacture, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

POWER ON/OFF SWITCH: The Power switch used in this piece of equipment DOES NOT break the

connection from the mains.

MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or installation where

plug is not accessible, an all-pole mains switch with a contact separation of at least 3 mm in each

pole shall be incorporated into the electrical installation of the rack or building.

If connected to 240V supply, a suitable CSA/UL certified power cord shall be used for this supply.

This Equipment is intended for rack mount use only.

IMPORTANT SAFETY INSTRUCTIONS

ELECTROMAGNETIC COMPATIBILITY

This device complies with part 15 of the FCC Rules and the Product

Specifications noted on the Declaration of Conformity. Operation

is subject to the following two conditions:

• this device may not cause harmful interference, and

• this device must accept any interference received, including

interference that may cause undesired operation.

Operation of this unit within significant electromagnetic fields should be

avoided.

• use only shielded interconnecting cables.

DECLARATION OF CONFORMITY

Manufacturer’s Name: BSS Audio

Manufacturer’s Address: 10653 S. River Front

Parkway, Suite 300

South Jordan, Utah

84095, USA

declares that the product:

Product name: BLU 120, BLU 160,

BLU 320, BLU 325,

BLU 326, BLU 800,

BLU 805 and BLU 806

Note: Product name may be suffixed by a

combination of the letters EU, M, or V.

Product option: Various I/O Cards

conforms to the following Product Specifications:

Safety: IEC 60065 -01+Amd 1 & 2

EMC: EN 55022:2010

EN 55024:2010

FCC Part 15

Supplementary Information:

The product herewith complies with the

requirements of the:

Low Voltage Directive 2014/35/EU

EMC Directive 2014/30/EU

RoHS Directive 2011/65/EU

WEEE Directive 2012/19/EU

With regard to Directive 2005/32/EC and

EC Regulation 1275/2008 of 17 December

2008, this product is designed, produced, and

classified as Professional Audio Equipment and

thus is exempt from this Directive.

C. Rex Reed

Director, Engineering

Signal Processing

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, USA

Date: August 15, 2016

European Contact:

Harman International

Salisbury House

London Wall

EC2M 5QQ

+44 207 562 9450

Harman Professional Inc.

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, USA

Ph: (801) 566-8800

Fax: (801) 568-7583

DECLARATION OF CONFORMITY

Manufacturer’s Name: BSS Audio

Manufacturer’s Address: 10653 S. River Front

Parkway, Suite 300

South Jordan, Utah

84095, USA

declares that the product:

Product name: BLU 326 (DA) and 806 (DA)

Note: Product name may be suffixed by a

combination of the letters EU, M, or V.

Product option: Various I/O Cards

conforms to the following Product Specifications:

Safety: IEC 60065: 8th Ed. 2014

EMC: EN 55032: 2012

EN 55024: 2010

FCC Part 15

Supplementary Information:

The product herewith complies with the

requirements of the:

Low Voltage Directive 2014/35/EU

EMC Directive 2014/30/EU

RoHS Directive 2011/65/EU

WEEE Directive 2012/19/EU

With regard to Directive 2005/32/EC and

EC Regulation 1275/2008 of 17 December

2008, this product is designed, produced, and

classified as Professional Audio Equipment and

thus is exempt from this Directive.

C. Rex Reed

Director, Engineering

Signal Processing

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, USA

Date: March 14, 2017

European Contact:

Harman International

Salisbury House

London Wall

EC2M 5QQ

+44 207 562 9450

Harman Professional Inc.

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, USA

Ph: (801) 566-8800

Fax: (801) 568-7583

SAFETY INSTRUCTIONS

NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD.

WARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE

EARTHING CONNECTION.

THE CORES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

GREEN AND YELLOW - EARTH BLUE - NEUTRAL BROWN - LIVE

AS COLOURS OF THE CORES IN THE MAINS LEAD OF THIS APPLIANCE MAY NOT CORRESPOND WITH THE

COLOURED MARKINGS IDENTIFYING THE TERMINALS IN YOUR PLUG, PROCEED AS FOLLOWS:

• THE CORE WHICH IS COLOURED GREEN AND YELLOW MUST BE CONNECTED TO THE TERMINAL IN

THE PLUG MARKED WITH THE LETTER E, OR WITH THE EARTH SYMBOL, OR COLOURED GREEN, OR

GREEN AND YELLOW.

• THE CORE WHICH IS COLOURED BLUE MUST BE CONNECTED TO THE TERMINAL MARKED N OR

COLOURED BLACK.

• THE CORE WHICH IS COLOURED BROWN MUST BE CONNECTED TO THE TERMINAL MARKED L OR

COLOURED RED.

THIS EQUIPMENT MAY REQUIRE THE USE OF A DIFFERENT LINE CORD, ATTACHMENT PLUG, OR BOTH,

DEPENDING ON THE AVAILABLE POWER SOURCE AT INSTALLATION. IF THE ATTACHMENT PLUG NEEDS TO

BE CHANGED, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WHO SHOULD REFER TO THE TABLE

BELOW. THE GREEN/YELLOW WIRE SHALL BE CONNECTED DIRECTLY TO THE UNITS CHASSIS.

CONDUCTOR

WIRE COLOR

Normal Alt

L LIVE BROWN BLACK

N NEUTRAL BLUE WHITE

E EARTH GND GREEN/YEL GREEN

WARNING: IF THE GROUND IS DEFEATED, CERTAIN FAULT CONDITIONS IN THE UNIT OR IN THE SYS-

TEM TO WHICH IT IS CONNECTED CAN RESULT IN FULL LINE VOLTAGE BETWEEN CHASSIS AND EARTH

GROUND. SEVERE INJURY OR DEATH CAN THEN RESULT IF THE CHASSIS AND EARTH GROUND ARE

TOUCHED SIMULTANEOUSLY.

WARNING:

• APPARATET MÅ TILKOPLES JORDET STIKKONTAKT.

• APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG.

• LAITE ON LIITETTÄVÄ SUOJAKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN.

• APPARATET SKAL TILSLUTTES JORDET STIKKONTAKT.

CONSIGNES DE SÉCURITÉ IMPORTANTES

Ne pas jeter ce produit avec les ordures ménagères. Il existe un système de collecte sélective pour les produits

électroniques usagés en conformité avec les lois en vigueur en matière de traitement, de récupération et de recyclage.

Dans les 25 États membres de l'UE, en Norvège et en Suisse, les ménages peuvent envoyer leurs produits électroniques

usagés sans frais vers des centres de collecte sélective ou chez un distributeur (contre l'achat d'un nouveau produit).

Contacter les autorités locales pour connaître les procédures de traitement des déchets adaptées dans les pays non

mentionnés ci-dessus.

Non seulement cette précaution vous permettra d’être sûr que votre produit est correctement traité, récupéré et recyclé,

mais elle vous évitera également de nuire involontairement à l'environnement et à la santé humaine.

AVERTISSEMENT CONCERNANT

LA FICHE SECTEUR

Une fiche secteur moulée qui a été coupée du cordon est dangereuse.

Jeter la fiche secteur dans un centre de déchets adapté.

VOUS NE DEVEZ EN AUCUNE CIRCONSTANCE INSÉRER

UNE FICHE ENDOMMAGÉE OU COUPÉE DANS UNE PRISE

SECTEUR 13 AMP.

Ne pas utiliser la fiche secteur si le couvercle du coffret à fusibles n'est

pas bien en place. Vous pouvez vous procurer des capots de fusible de

rechange auprès de votre détaillant local. Les fusibles de remplacement

sont de 13 A et DOIVENT être approuvés ASTA, BS1362.

Les symboles illustrés ci-dessus sont des symboles acceptés

internationalement qui avertissent des dangers potentiels relatifs à

l’utilisation de produits électriques. Le voyant clignotant avec une flèche

dans un triangle équilatéral signifie la présence de tensions dangereuses

dans l'appareil. Le point d’exclamation dans un triangle équilatéral

indique que l’utilisateur doit se référer au manuel d'utilisation.

Ces symboles indiquent qu’il n’y a aucune pièce utilisable par l’utilisateur

à l’intérieur de l’appareil. Ne pas ouvrir l’appareil. Ne pas essayer de

réparer soi-même l’appareil. Confier toute réparation à du personnel

qualifié. Ouvrir la structure de l’appareil pour quelque raison que ce soit

annulera la garantie du fabricant. Ne pas mouiller l’appareil. Si du liquide

est renversé sur l’appareil, fermer immédiatement l’appareil et l’apporter

chez un réparateur. Débrancher l’appareil pendant les tempêtes afin

d’éviter des dommages.

Ce qui suit est représentatif d’une

utilisation à basse altitude ; ne pas

utiliser ce produit au-dessus de 2000 m.

AVERTISSEMENT POUR VOTRE SÉCURITÉ

LIRE ATTENTIVEMENT :

LIRE CES CONSIGNES.

CONSERVER CES CONSIGNES.

RESPECTER TOUS LES AVERTISSEMENTS.

SUIVRE TOUTES LES CONSIGNES.

NE PAS UTILISER CET APPAREIL PRÈS DE L’EAU.

NETTOYER UNIQUEMENT AVEC UN CHIFFON SEC.

POUR USAGE INTÉRIEUR UNIQUEMENT.

NE PAS OBSTRUER LES OUÏES D’AÉRATION. EFFECTUER L’INSTALLATION CONFORMÉMENT AUX

INSTRUCTIONS DU FABRICANT.

NE PAS INSTALLER À PROXIMITÉ DE SOURCES DE CHALEUR TELLES QUE DES RADIATEURS,

BOUCHES D’AÉRATION, PLAQUES CHAUFFANTES OU TOUT AUTRE APPAREIL (Y COMPRIS DES

AMPLIFICATEURS) DÉGAGEANT DE LA CHALEUR.

UTILISER UNIQUEMENT LES PIÈCES/ACCESSOIRES MENTIONNÉS PAR LE FABRICANT.

DÉBRANCHER L'APPAREIL AU COURS DES ORAGES OU EN CAS DE NON-UTILISATION PENDANT UNE

DURÉE PROLONGÉE.

Ne pas détériorer la sécurité de la fiche polarisée ou de la fiche de terre. Les fiches polarisées sont

équipées de deux bornes de largeurs différentes. Les fiches de terre comportent deux lames et une

troisième broche de mise à la terre. La broche la plus large ou troisième broche de mise à la terre

est prévue pour votre sécurité. Si la fiche fournie ne correspond pas à votre installation électrique,

faire appel à un électricien pour remplacer la prise hors normes.

Protéger le cordon d'alimentation contre les risques de piétinement ou de pincement, notamment

au niveau des fiches, des prises de courant et du point d'attache avec le matériel.

Utiliser uniquement le chariot, le support, le trépied ou la table spécifié(e)

par le fabricant ou vendu(e) avec le matériel. Si vous utilisez un chariot

pour déplacer l'appareil, soyez suffisamment prudent pour éviter une

éventuelle blessure consécutive au basculement du chariot et de sa charge.

Les réparations doivent être confiées à un technicien S.A.V. qualifié. Une réparation est nécessaire en

cas de dommage quelconque et en particulier en cas d'endommagement du cordon d’alimentation

ou de la fiche électrique, d'infiltration liquide, d'introduction involontaire d'un objet dans l'appareil,

d'exposition de l’appareil à la pluie ou à un milieu humide, de fonctionnement anormal ou de chute

de l'appareil.

INTERRUPTEUR MARCHE/ARRÊT : l'interrupteur d'alimentation de cet équipement NE coupe PAS

la connexion secteur.

DÉBRANCHEMENT DE L'APPAREIL : la prise de courant doit rester facilement accessible. Pour un

montage en rack ou une installation avec une prise inaccessible, un interrupteur omnipolaire à

distance d'ouverture de contact d'au moins 3 mm doit être intégré à l’installation électrique du

rack ou du local.

Si le matériel est relié à une alimentation de 240 V, utiliser impérativement un cordon d'alimentation

adapté certifié CSA/UL pour ce branchement.

Cet équipement est exclusivement destiné à un montage en rack.

CONSIGNES DE SÉCURITÉ IMPORTANTES

COMPATIBILITÉ ÉLECTROMAGNÉTIQUE

Cet appareil est conforme au volet 15 des règles du FCC et aux

spécifications techniques évoquées dans la Déclaration de

conformité. Son fonctionnement est soumis aux deux conditions

suivantes :

• cet appareil ne doit pas causer d’interférences nuisibles et

• cet appareil doit accepter les interférences captées, y compris les

interférences susceptibles de nuire à son fonctionnement.

L’utilisation de cet appareil à proximité de champs électromagnétiques

puissants n’est pas recommandée.

• utiliser exclusivement des câbles d’interconnexion blindés.

CONSIGNES DE SÉCURITÉ

NOTICE ADRESSÉE AUX CONSOMMATEURS ÉQUIPÉS D’UN MATÉRIEL AVEC CORDON D’ALIMENTATION

FOURNI.

AVERTISSEMENT : CET APPAREIL DOIT ÊTRE BRANCHÉ SUR UNE PRISE SECTEUR DOTÉE D'UNE PROTEC-

TION PAR MISE À LA TERRE.

LES COULEURS DES NOYAUX DANS LES FILS SECTEURS DOIVENT RESPECTER LES CODES SUIVANTS :

VERT ET JAUNE - TERRE BLEU - NEUTRE MARRON - PHASE

LES COULEURS DES NOYAUX DANS LES FILS SECTEURS DE CET APPAREIL PEUVENT NE PAS CORRESPON-

DRE AUX INSCRIPTIONS COLORÉES IDENTIFIANT LES TERMINAUX DANS VOTRE FICHE ; IL FAUT DONC

PROCÉDER DE LA FAÇON SUIVANTE :

• LE NOYAU VERT ET JAUNE DOIT ÊTRE BRANCHÉ AU TERMINAL DE LA FICHE OÙ APPARAÎT LA LETTRE E

OU LE SYMBOLE DE MISE À LA TERRE, OU AU TERMINAL VERT OU VERT ET JAUNE.

• LE NOYAU BLEU DOIT ÊTRE BRANCHÉ AU TERMINAL MARQUÉ D’UN N OU DE COULEUR NOIRE.

• LE NOYAU MARRON DOIT ÊTRE BRANCHÉ AU TERMINAL MARQUÉ D’UN L OU DE COULEUR ROUGE.

CE MATÉRIEL PEUT NÉCESSITER L’UTILISATION D’UN CORDON D’ALIMENTATION DIFFÉRENT ET/OU

D’UNE FICHE DE BRANCHEMENT DIFFÉRENTE SELON LA SOURCE D’ALIMENTATION DISPONIBLE À

L’INSTALLATION. SI LA FICHE DE BRANCHEMENT DOIT ÊTRE CHANGÉE, FAIRE APPEL À UN TECHNICIEN

QUALIFIÉ QUI DEVRA SE RÉFÉRER AU TABLEAU CI-DESSOUS. LE FIL VERT/JAUNE DOIT ÊTRE BRANCHÉ

DIRECTEMENT AU CHÂSSIS DE L'APPAREIL.

CONNECTEURS

COULEUR DU FIL

Normal Alt

L PHASE MARRON NOIR

N NEUTRE BLEU BLANC

E TERRE VERT/JAU VERT

ATTENTION : UN DÉFAUT DE MISE À LA TERRE PEUT PROVOQUER CERTAINS DYSFONCTIONNEMENTS

DE L'APPAREIL OU DU SYSTÈME AUQUEL IL EST RELIÉ, POUVANT SE TRADUIRE PAR UNE TENSION COM-

POSÉE ENTRE LA MASSE ET LA PRISE DE TERRE. CELA PEUT PROVOQUER DES BLESSURES SÉRIEUSES OU

FATALES SI LA MASSE ET LA PRISE DE TERRE SONT TOUCHÉES EN MÊME TEMPS.

ATTENTION :

• APPARATET MÅ TILKOPLES JORDET STIKKONTAKT.

• APPARATEN SKALL ANSLUTAS TILL JORDAT UTTAG.

• LAITE ON LIITETTÄVÄ SUOJAKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN.

• APPARATET SKAL TILSLUTTES JORDET STIKKONTAKT.

DÉCLARATION DE CONFORMITÉ

Nom du fabricant : BSS Audio

Adresse du fabricant : 10653 S. River Front

Parkway, Suite 300

South Jordan, Utah 84095,

ÉTATS-UNIS

déclare que le produit :

Nom du produit : BLU 120, BLU 160,

BLU 320, BLU 325,

BLU 326, BLU 800,

BLU 805 and BLU 806

Remarque : Nom du produit peut être suffixé

par une combinaison des lettres de l’UE ,

M ou V.

Option du produit : Divers I / O Cartes

est conforme aux spécifications suivantes :

Sécurité : CEI/IEC 60065:2001 +

Amd 1 et 2

CEM : EN 55022:2010

EN 55024:2010

Partie 15 des FCC

Informations complémentaires :

Ce produit est conforme aux exigences

suivantes :

Directive sur la basse tension 2014/35/UE

Directive 2014/30/UE

Directive RoHS 2011/65/UE

Directive DEEE 2012/19/UE

Ce produit appartenant à la catégorie Matériel

audio professionnel, il n’est pas concerné par

la directive 2005/32/CE ou par le règlement

européen 1275/2008 du 17 décembre

2008.

C. Rex Reed

Directeur, Ingénierie

Traitement des signaux

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, ÉTATS-UNIS

Date : 15 août 2016

Contactez européenne :

Harman International

Salisbury House

London Wall

EC2M 5QQ

+44 207 562 9450

Harman Professional Inc

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, ÉTATS-UNIS

Tél. : (801) 566-8800

Fax : (801) 568-7583

DÉCLARATION DE CONFORMITÉ

Nom du fabricant : BSS Audio

Adresse du fabricant : 10653 S. River Front

Parkway, Suite 300

South Jordan, Utah 84095,

ÉTATS-UNIS

déclare que le produit :

Nom du produit : BLU 326 (DA) and 806 (DA)

Remarque : Nom du produit peut être suffixé

par une combinaison des lettres de l’UE ,

M ou V.

Option du produit : Divers I / O Cartes

est conforme aux spécifications suivantes :

Sécurité : CEI/IEC 60065 : 8e éd.

2014

CEM : EN 55032 : 2012

EN 55024 : 2010

Partie 15 des FCC

Informations complémentaires :

Ce produit est conforme aux exigences

suivantes :

Directive sur la basse tension 2014/35/UE

Directive 2014/30/UE

Directive RoHS 2011/65/UE

Directive DEEE 2012/19/UE

Ce produit appartenant à la catégorie Matériel

audio professionnel, il n’est pas concerné par

la directive 2005/32/CE ou par le règlement

européen 1275/2008 du 17 décembre

2008.

C. Rex Reed

Directeur, Ingénierie

Traitement des signaux

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, ÉTATS-UNIS

Date : 14 mars 2017

Contactez européenne :

Harman International

Salisbury House

London Wall

EC2M 5QQ

+44 207 562 9450

Harman Professional Inc

10653 S. River Front Parkway, Suite 300

South Jordan, Utah 84095, ÉTATS-UNIS

Tél. : (801) 566-8800

Fax : (801) 568-7583

Table of Contents

Product Registration/Warranty �� 1

Mechanical Installation �� 1

Front Panel �� 2

Input Card Monitoring �� 2

Clip �� 2

Signal �� 2

Sync/48V �� 2

Conductor [BLU-800/BLU-320/BLU160/BLU-120]

Master [BLU-805/BLU-806 (DA)/BLU-325/BLU-326 (DA)] �� 2

Network Link �� 2

Data Activity �� 2

LCD Display �� 2

LOCATE �� 2

Contrast (Hold) �� 2

Rear Panel �� 3

AC Mains �� 3

CobraNet

Connectors–Primary/Secondary [BLU-800/BLU-320] �� 3

AVB [BLU-805/BLU-325] �� 3

Dante

/AES67 [BLU-806 (DA)/BLU-326 (DA)]�� 3

BLU link �� 3

Locate �� 4

RS232 �� 4

Ethernet�� 4

Word Clock

[Buddy Link or 48k] [BLU-800/BLU-805/BLU-806 (DA)/BLU-320/BLU-325/BLU-326 (DA)] �� 4

Audio Cable Wiring �� 4

Audio Input & Output Wiring Convention �� 4

I/O Card Positions A, B, C & D �� 5

Control Inputs �� 5

2-Wire Mode �� 5

3-Wire Mode �� 5

Logic Outputs �� 6

Opto Output �� 6

Technical Specifications �� 7

Product Registration/Warranty

To register your product, please visit http://bssaudio�com/en-US/support/warranty_registration�

For warranty information, please visit http://bssaudio�com/en-US/support/warranty_policy�

Mechanical Installation

OF FIRE REPLACE ONLY WITH THE

ETHERNET

PRIMARY

SECONDARY

12341

OUT

CAUTION:

TO REDUCE THE RISK

SAME TYPE AND RATING OF FUSE

AVIS:

UTILISER UN FUSIBLE DE

RECHANGE DE MEME TYPE

THIS EQUIPMENT MUST BE EARTHED

MANUFACTURED IN

THE USA BY

BSS AUDIO

RS232LOCATE

SSSS

WORD CLOCK

T1.6AH - 250V FUSE

100-240V ~ 50/60Hz, 55W

CobraNet

BLU link

OUT

If the unit is likely to undergo extreme vibration through extensive road trucking and touring, the unit must be

supported at the rear and/or sides to lessen the stress on the front mounting ange. The necessary support can

generally be bought ready-built as a rack tray, or the BLU-800/805/806 (DA)/320/325/326 (DA)/160/120 unit

can be mounted between other units. Damage caused by insufcient support is not covered by the warranty. To

prevent cosmetic damage to the front panel nish, use protective plastic cups under the rack mounting bolts.

Front Panel

Input Card Monitoring

Each channel has 3 LED indicators showing:

• Clip

Illuminated–Indicates clipping in the analogue domain for each channel of the

tted Input or Output card. The LED will illuminate at +18.5dB.

• Signal

Illuminated–The Signal LED will illuminate for each channel of a tted Input or

Output card when the signal reaches or exceeds the signal threshold of -20dB�

• Sync/48V

Illuminated–Illuminates to indicate +48V phantom power has been activated

for the relevant channel of a tted input card. Also indicates sync status for

digital I/O card�

Conductor [BLU-800/BLU-320/BLU160/BLU-120]

Master [BLU-805/BLU-806 (DA)/BLU-325/BLU-326 (DA)]

The master clock device of a CobraNet

system is referred to as the Conductor–

the CM-1 modules in the system auto-negotiate which device will transmit the

Conductor beat packet� The LED illuminates to indicate which device is acting

as the Conductor� The master clock device of an AVB or Dante™ system is

indicated with a Master LED on the front panel of the device that is providing

the master clock function�

Network Link

The Network Link indicates the presence of Cat 5 Ethernet cables� If no

cables are connected, the LED is unlit; the LED ashes if either a control

or CobraNet

/AVB/ Dante™ cable is tted and remains illuminated if both

cables are connected�

Data Activity

The Data Activity LED will ash to indicate that the device is communicating

with another control device, either on the network or via the serial or control

ports�

LCD Display

Top line Indicates device name and run state� Bottom line indicates Time, IP Address, Subnet Mask, and Model

number with rmware version. Also, the device’s MAC Address can be viewed by powering the device on whilst

pressing and holding the Locate switch�

LOCATE

Pressing the Locate switch on the front of

the unit will illuminate the Locate switch

on the rear and identify the device within

London Architect� Similarly the switch will

illuminate if the device is selected from

within London Architect or from the Locate

switch on the rear�

Contrast (Hold)

Pressing and holding the Locate switch will cycle the LCD through its contrast range�

Rear Panel

OF FIRE REPLACE ONLY WITH THE

ETHERNET

PRIMARY

SECONDARY

12341

OUT

CAUTION:

TO REDUCE THE RISK

SAME TYPE AND RATING OF FUSE

AVIS:

UTILISER UN FUSIBLE DE

RECHANGE DE MEME TYPE

THIS EQUIPMENT MUST BE EARTHED

MANUFACTURED IN

THE USA BY

BSS AUDIO

RS232LOCATE

SSSS

WORD CLOCK

T1.6AH - 250V FUSE

100-240V ~ 50/60Hz, 55W

CobraNet

BLU link

OUT

BLU-800 shown above� BLU-320 layout is identical� BLU-

160 and BLU-120 have no CobraNet

or WORD CLOCK

BNC connectors, but are otherwise identical to the BLU-

800 and BLU-320�

BLU-805 shown above� BLU-325 layout is identical�

BLU-806 (DA) shown above� BLU-326 (DA) layout is

identical�

AC Mains

AC Mains input to the universal switched-mode power supply, operates over a wide range of AC input voltages

from 100V to 240V, 50/60Hz�

CobraNet

Connectors–Primary/Secondary [BLU-800/BLU-320]

CobraNet

is a licensed technology which allows CobraNet

enabled Soundweb London devices to send

and receive (simultaneously) up to 32 channels of audio to and from other CobraNet

enabled devices� The

CobraNet

compatible devices within the Soundweb

London system are tted with a Peak Audio Cobranet

CM-1 module� The module itself offers a Primary and a Secondary Cobranet

port� Under normal operation,

only the Primary port transmits and receives data to and from the network� Should the Primary port or connection

fail, the CM-1 module automatically switches to receive from and transmit with the Secondary port�

AVB [BLU-805/BLU-325]

Ethernet AVB, or Audio/Video Bridging, is a common name for a set of IEEE standards that ensure the transmission

of high quality streaming audio and video over a standard Ethernet connection� The BLU-805 and BLU-325

devices are tted with an AVB module. The module allows Soundweb London devices to send and receive

(simultaneously) up to 64 channels of audio to and from other AVB-enabled devices�

The module offers a Primary and a Secondary AVB port� Under normal operation, only the Primary port

transmits and receives data to and from the network� Should the Primary port or connection fail, the AVB

module automatically switches to receive from and transmit with the Secondary port� NOTE: The Secondary

port is not currently enabled� It will be enabled in a future release of HiQnet London Architect� The physical

AVB connections must be made using Cat 5e cables and an AVB compatible network switch� See ‘Technical

Specications’ for compatible Ethernet Switches. Do not connect the AVB ports to any switch which does not

support AVB! When connecting only two AVB devices together, a direct connection between devices can be

made from the primary of one device to the primary of the other�

Dante

/AES67 [BLU-806 (DA)/BLU-326 (DA)]

Dante

is a licensed technology from Audinate®� It uses standard Internet Protocols over 100Mb and/or Gigabit

Ethernet and is capable of transporting professional quality, low-latency audio� Dante

runs on inexpensive

off-the-shelf computer networking hardware and does not require dedicated network infrastructure; Ethernet

switches transmit Dante

digital media streams alongside ordinary data trafc. The BLU-806 (DA) and BLU-

326 (DA) devices are tted with a Dante

module� The module allows Soundweb London devices to send and

receive up to 64X64 channels of audio at 48 kHz (up to 32X32 channels at 96 kHz) to and from other Dante

enabled devices� The module offers a Primary and a Secondary Dante

port�

The Secondary port can be congured for Swithed or Redundant operation using the Dante Controller software.

When a device is set for Redundant operation, the device will duplicate Dante audio trafc to both Primary and

Secondary Ethernet ports� When a device is set for Switched operation, the Secondary Ethernet port will behave

as a standard switch port, allowing daisy-chaining through the device� The physical Dante

connections must

be made using Cat 5e or Cat 6 cables when using a Gigabit network (Cat 5 may be used for purely 100Mbps

networks)� AES67 audio transmission is achieved through the Dante ports on the BLU-806DA and BLU-326DA

only� AES67 must be transmitted at 48kHz�

BLU link

The Soundweb London digital audio bus (also informally referred to as “BLU link”) is a point-to-point digital

audio bus with 256 audio channels at 48K sample rate or 128 audio channels at 96K sample rate� The physical

connection is made with Cat 5e cable from the OUT port of one device to the IN port of another device� The

devices are connected in a daisy chain fashion continuing with the OUT port of one device connected to the

IN port of the next device� Redundancy can be provided by completing the loop and connecting the OUT port

audio sample rate.

Locate

Pressing the Locate switch on the rear of the unit will illuminate the Locate switch on the front and identify the

device within London Architect. Similarly the switch will illuminate if the device is selected from within London

Architect or from the Locate switch on the front panel.

RS232

The serial port allows 3rd-party control equipment to control and monitor the Soundweb London. The Soundweb

London can also send custom serial strings (in Decimal, Hexadecimal, or ASCII format) through the serial port.

Therefore, the Soundweb London can control virtually any device which has a serial port and a publicly

available protocol guide.

Ethernet

The main connection for the proprietary system control network. The Ethernet port allows BLU-8v2’s, BLU-

10’s, HiQnet London Architect, iOS devices, and 3rd-party control equipment to control and monitor the

from HiQnet London Architect. The Soundweb London can also send custom Ethernet messages (UDP or TCP;

in Decimal, Hexadecimal, or ASCII format) through the Ethernet port. Therefore, the Soundweb London can

control virtually any device which has an Ethernet port and a publicly available protocol guide.

Word Clock

[Buddy Link or 48k] [BLU-800/BLU-805/BLU-806 (DA)/BLU-320/BLU-325/BLU-326 (DA)]

On CobraNet

Soundweb London devices to be linked together and operate as a redundant pair. A 48kHz system clock is

generated at the BNC OUT port when used in this fashion. If ‘Box B’ ceases to receive the 48kHz system clock

from ‘Box A’, due to power failure of ‘Box A’, ‘Box B’ will take over and begin receiving and transmitting audio

over the CobraNet

network.

These connectors can also facilitate integration with external clocks when using BLU link or Dante

, allowing

the Soundweb London devices to sync to a ‘house clock’, a common requirement in post-production, theatre,

and broadcast applications. Synchronizing the Soundweb London internal DSP processing clock to the house

clock avoids having to use Sample Rate Conversion on digital signals, resulting in superior audio. The supported

sync frequencies are 48 kHz, 48 kHz pull-down (47.952 kHz), 96 kHz, and 96 kHz pull-down (95.904 kHz).

London device is running will be present on the WORD CLOCK OUT.

NOTE: The BNC WORD CLOCK connectors serve no function when using AVB.

Audio Cable Wiring

All audio and control connections are made via Klippon pluggable terminal block connectors (also known as

BL, Phoenix or Combicon). 6-way female Klippon connectors (part number: 32-1226) are supplied for making

these connections.

Audio Input & Output Wiring Convention

Soundweb products provide cable shielding ‘back from the destination’ to eliminate ground loop problems.

This means that the shield (S) connection on an input is grounded, whereas the shield connection on an output

Balanced wiring–The convention for balanced

wiring (2-core plus shield) is shown here:

Unbalanced wiring–The convention for unbalanced

wiring to the inputs (1-core plus shield) is shown

here:

Balanced cable

Shield

Hot

Cold

Unbalanced cable

Shield

Hot

Link between

pins (S) and (-)

(optional for inputs)

I/O Card Positions A, B, C & D

OF FIRE REPLACE ONLY WITH THE

ETHERNET

PRIMARY

SECONDARY

12341

OUT

CAUTION:

TO REDUCE THE RISK

SAME TYPE AND RATING OF FUSE

AVIS:

UTILISER UN FUSIBLE DE

RECHANGE DE MEME TYPE

THIS EQUIPMENT MUST BE EARTHED

MANUFACTURED IN

THE USA BY

BSS AUDIO

RS232LOCATE

SSSS

WORD CLOCK

T1.6AH - 250V FUSE

100-240V ~ 50/60Hz, 55W

CobraNet

BLU link

OUT

These connectors provide the balanced connections for the I/O card tted in the four card slots in a Soundweb

London device� The analogue connections are balanced, on Phoenix/Combicon connectors� A green LED next

to the slot assignment letter A, B, C or D indicates that an Input card is tted and an amber LED when an output

card is tted. Digital input cards are indicated with a blue LED and digital outputs cards with a red LED. AEC

input cards are indicated with a white LED� Telephone Hybrid cards are indicated with a yellow LED�

Control Inputs

There are 12 control inputs, also known as ‘General Purpose Inputs’ or

‘GPI’. The control inputs are used to connect contact closures (for control of

binary parameters, such as mutes), resistor ladders (for control of multistate

parameters, such as source selectors) or potentiometers (for control of

continuous parameters, such as volume faders)� There are two common

(ground) connections ‘C’ to the left of the 12 control inputs, and two software-

assignable reference voltage outputs ‘R’ to the right. The control ports have two

modes of operation: 2-wire and 3-wire�

2-Wire Mode

In this mode, the 12 control inputs are internally ‘pulled up’ to +5V DC via

a 4�7kOhm resistor� Therefore, no external voltage source is needed to create

contact closure to ground for switches such as mute buttons or, resistance to

ground (for other multi-state or continuous controls such as Parameter Presets

or faders)�

See the Soundweb London help for a table of resistor values for use with

Parameter Presets or source selectors�

A 47kOhm-log potentiometer connected between a control input and

common will allow parameters to be controlled linearly�

switch

2-wire mode

3600R

1800R

1200R

unconnected

ladder

47kOhm

log

potentiometer

470R

3-Wire Mode

This mode allows the use of linear pots or faders for continuous controls� A

pot would be wired as a potential divider with the top of the track connected

to the reference output R, the wiper to a control input and the bottom of the

track to a common C� High performance pots with track resistance between

10kOhms and 100kOhms are recommended�

10K-100kOhm

linear

potentiometer

switch

ladder

4k7

3-wire mode

Logic Outputs

There are 6 logic outputs, also known as “General Purpose Outputs” or

“GPO”. They are used to control LED’s or relays. The logic output can source

10mA at 5V DC, or sink 60mA up to 50V DC�

A high sensitivity relay (such as a reed relay) can be driven by connecting

multiple logic outputs in parallel� In the diagram to the right, this arrangement

will develop 4V across a 500-Ohm coil, providing that all four outputs are

activated simultaneously�

LED

relay

When sourcing from the Logic Output, an LED connected

between one output (Anode, A) and common (Cathode,

K) will illuminate when the logic output is activated,

without requiring any external current limiting resistor (the

Soundweb London contains an internal 440 Ohm resistor)�

Port 1

Current source, 10mA max

LED

LD5

For higher current reed type relays you must use the Logic Output

to sink current using an external power supply�

Port 1

Current sink, 60mA max

External supplyVCC

Opto Output

In addition to the six standard logic outputs, there is

an isolated output, which fails safe (open circuit) if the

unit becomes faulty�

relay

+supply voltage

ground

Technical Specications

FRONT PANEL LED INDICATORS

INPUT/OUTPUT: Per Input: Signal Present, CLIP, SYNC/48V, I/O card type [IN, OUT, DIG, AEC[BLU-800,

BLU-805, BLU-806 (DA), BLU-320, BLU-326 (DA), BLU-325, BLU-160, BLU-120]

OTHER: LCD Display, Conductor active, Net Link active, Data Activity

ANALOGUE INPUTS

CONNECTORS: Up to 16 electronically balanced on Phoenix/Combicon removable screw connectors

MIC/LINE INPUTS: Nominal gain 0dB, electronically switchable up to +48dB, in +6dB steps

INPUT IMPEDANCE: 3�5kOhm

MAXIMUM INPUT LEVEL: +20dBu with 0dB input gain, [+8dBu with 12dB gain]

CMRR: >40dB at 1kHz

EQUIV. INPUT NOISE [EIN]: <-123dBu typ� with 150 Ohms source

PHANTOM POWER: 48V nominal, selectable per input

A/D LATENCY [REV. A]: 41/Fs [0�85ms@48k, 0�43ms@96k]

A/D LATENCY [REV. B]: 12/Fs [0�25ms@48k, 0�13ms@96k]

A/D BIT DEPTH: 24-bit

DIGITAL INPUTS

CONNECTORS: Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors

INPUT IMPEDANCE: 110 ohm [AES/EBU], 75 ohm [S/PDIF]

SAMPLE RATE: 48kHz or 96kHz

SAMPLE RATE CONVERSION: 8kHz-96kHz

THD+N: <-140dB

LATENCY: 3/Fso + [56.581/Fsi] + [55.658/Fso]

AEC ANALOGUE INPUTS

CONNECTORS: Up to 16 electronically balanced on Phoenix/Combicon removable screw connectors

MIC/LINE INPUTS: Nominal gain 0dB, electronically switchable up to +48dB, in +6dB steps

INPUT IMPEDANCE: 3�5kOhm

MAXIMUM INPUT LEVEL: +20dBu with 0dB input gain, +8dBu with 12dB gain

CMRR: >75dB at 1kHz

EQUIV. INPUT NOISE [EIN]: <-128dBu typical with 150 Ohms source

PHANTOM POWER: 48V nominal, selectable per input

PRE-AEC INPUT LATENCY: 38/Fs [0�79ms@48k]

POST-AEC INPUT LATENCY: (Original 8k Algorithm): 2385/Fs [49�68ms@48k]

(Full Bandwidth Algorithm): 1609/Fs [33�52ms@48k]

TAIL LENGTH: 200 ms

CONVERGENCE RATE: 49 dB/s [Average convergence rate]

TELEPHONE INTERFACE, ANALOGUE INPUTS

CONNECTORS: 2 electronically balanced on Phoenix/Combicon removable screw connectors

MIC/LINE INPUTS: Nominal gain 0dB, electronically switchable up to +48dB, in +6dB steps

INPUT IMPEDANCE: 3�5kOhm

MAXIMUM INPUT LEVEL: +20dBu with 0dB input gain, +8dBu with 12dB gain, balanced, 150 ohm

CMRR: >75dB at 100Hz, >66dB at 1kHz

EQUIV. INPUT NOISE [EIN]: <-128dBu typical with 150 Ohms source, 20kHz, +48dB gain

PHANTOM POWER: 48V nominal, selectable per input

A/D LATENCY: 12/Fs [0�25ms@48k]

TELEPHONE INTERFACE

AC-REN: 0�0B

DYNAMIC RANGE: 67 dB

FREQUENCY RESPONSE: 300 to 3�3kHz

THD: <0�3%

TRANSHYBRID LOSS: >48 dB with LEC enabled

LEC TAIL TIME: 64ms

TX LEVEL: -10dBm RMS average

RX LEVEL: +3.2dBm RMS

ANALOGUE OUTPUTS

CONNECTORS: Up to 16 electronically balanced on Phoenix/Combicon removable screw connectors

OUTPUT IMPEDANCE: 40 Ohms balanced, 20 Ohms unbalanced

MAXIMUM OUTPUT LEVEL: +19dBu

FREQUENCY RESPONSE: 20Hz to 20kHz [+0.5/-1dB]

THD: <0.01% [20Hz to 20kHz, +10dBu output]

DYNAMIC RANGE: 108dB typ� [22Hz to 22kHz unweighted]

CROSSTALK: <-75dB

D/A LATENCY: 28/Fs [0�58ms@48k, 0�29ms@96k]

D/A BIT DEPTH: 24-bit

DIGITAL OUTPUTS

CONNECTORS: Up to 16 AES/EBU or S/PDIF on Phoenix/Combicon removable screw connectors

OUTPUT IMPEDANCE: 110 ohm [AES/EBU], 75 ohm [S/PDIF]

SAMPLE RATE: 48kHz or 96kHz

SAMPLE RATE CONVERSION: 8kHz-96kHz

THD+N: <-140dB

LATENCY SRC OFF: 6/Fs [0�13ms@48k, 0�06ms@96k]

LATENCY SRC ON: 60/Fs [1�25ms@48k, 0�63ms@96k]

CONTROL PORTS

NUMBER OF PORTS: 12 inputs and 6 outputs

CONTROL INPUT VOLTAGE: 0 to 4�5v

CONTROL INPUT IMPEDANCE: 4.7kOhms to +5V [2-wire mode] >1MOhm [3-wire mode]

LOGIC OUTPUT VOLTAGE: 0 or +5V unloaded

LOGIC OUTPUT IMPEDANCE: 440 Ohm

LOGIC OUTPUT CURRENT: 10mA source, 60mA sink

WATCHDOG OUTPUT

CONNECTOR: Phoenix/Combicon connector for failsafe control

OPTO OUTPUT CURRENT: 14mA maximum

WITHSTANDING VOLTAGE: 80V maximum [Off]

SERIES IMPEDANCE: 220 Ohms [isolated]

CONTROL NETWORK

CONNECTORS: RJ45 Ethernet connector

MAXIMUM CABLE LENGTH: 100m/328ft on Category 5 cable between device and Ethernet switch

BLU LINK AUDIO NETWORK [BLU-800, 320, 160, 120]

CONNECTORS: 2 x RJ45 Ethernet connectors

MAXIMUM CABLE LENGTH: 100m/328ft on Category 5e cable between devices

LATENCY: 11/Fs [0�23ms@48k, 0�11ms@96k]

PASS THROUGH LATENCY: 4/Fs [0�08ms@48k, 0�04ms@96k]

COBRANET™ AUDIO NETWORK [BLU-80, 32, 800, 320]

CONNECTORS: 2 x RJ45 connectors

MAXIMUM CABLE LENGTH: 100m/328ft on Category 5 cable between device and Ethernet switch

LATENCY: 1�33ms-5�33ms

DANTE/AES67 AUDIO NETWORK [BLU-806 (DA), 326 (DA)]

CONNECTORS: 2 x RJ45 connectors

MAXIMUM CABLE LENGTH: 100m/328ft on Category 5 (100Mbps) or Category 5e/Category 6 (Gigabit) cable

between devices

LATENCY: 0�15ms-5�0ms

AVB AUDIO NETWORK [BLU-805, 325]

CONNECTORS: 2 x RJ45 connectors

MAXIMUM CABLE LENGTH: 100m/328ft on Category 5e cable between device and AVB compliant Ethernet switch

SAMPLE RATE: 48kHz

LATENCY: 0�5ms-2�0ms

COMPATIBLE AVB SWITCHES: BSS Audio/NETGEAR GS724T Ethernet Switch

LABX Titanium 411 Ruggedized AVB Ethernet Bridge Switch

POWER/TEMPERATURE

MAINS VOLTAGE: 100-240V AC, 50/60Hz

POWER CONSUMPTION: <35VA [BLU-80, 32, 16]; <55VA [BLU-800, 805, 806 (DA), 320, 325, 326 (DA), 160, 120]

BTU RATING: <120 BTU/hr [BLU-80, 32, 16]; <188 BTU/hr [BLU-800, 805, 806 (DA), 320, 325, 326 (DA),

160, 120]

OPERATING TEMPERATURE RANGE: 0º to 45º C [32º to 113º F]

PHYSICAL [BLU-120/160/320/325/326 (DA)/800/805/806 (DA)]

RACK SPACE: 1U

DIMENSIONS (H X W X D): 1�75” x 19” x 12�5” (45mm x 483mm x 318mm)

WEIGHT: 9 lbs / 4�1 kgs (estimated)

BSS Audio incorporates high quality mechanical fans in some products� All mechanical fans have a limited life

expectancy� We recommend annual inspection of fans for dust occlusion and excessive noise� Fan assemblies

should be replaced after six to ten years of use� Environmental factors such as elevated temperature, dust, and

smoke can adversely affect fan life� Systems exposed to these conditions should be inspected more frequently�

Fan replacement can be performed either at the factory or by an experienced technician in the eld. Please

contact BSS Technical Support for more information on purchasing replacement parts or product service�

BSS Audio has a policy of continued product improvement and accordingly reserves the right to change features

and specications without prior notice.

Phone:

(801) 566-8800

Website:

bssaudio.com

Support:

bssaudio.com/en-US/support

BSS Audio is a registered trademark of HARMAN

Printed in Malaysia

BSS Audio BLU-806DA (BLU-806) Guide d'installation

Marque: BSS Audio

Modèle: BLU-806DA (BLU-806)

Catégorie: Équipement musical supplémentaire

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: BSS Audio BLU-806DA (BLU-806) Installation guide

BSS Audio BLU-806DA (BLU-806) Guide d'installation

Ce manuel convient également à

BSS Audio BLU-806DA (BLU-806) Guide d'installation

dans d''autres langues

Documents connexes

Autres documents