Simplicity 020377-00 Manuel utilisateur

Simplicity
Marque
Simplicity
Modèle
020377-00
Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur

Ce manuel convient également à

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 317380GS Revision -
Pressure Washer/Laveuse haute pression/Hochdruckreiniger/
Lavadora de Pressão/Limpiadora a presión
Operator’s Manual/Manuel d’utilisation/Bedienerhandbuch/
Manual de Operação/Manual del Operario
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
BPW2000
Not for
Reproduction
2 BRIGGSandSTRATTON.COM2 BRIGGSandSTRATTON.COM
A
11
7
12
A
C
N
E
B
P
10
H
D
B
2
A
C
C
A
3
D
B
4
C
A
B
5
A
B
C
D
8
A
9
A
1
6
D
C
Not for
Reproduction
3 3
B
A
C
22
14
23
A
13
15
A
B
16
17
A
B
18
A
19
A
20
24
21
A
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® pressure waher. We are pleased that you’ve placed your confidence in the Briggs & Stratton brand. When operated
and maintained according to the instructions in this manual, your Briggs & Stratton pressure waher will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with pressure waher and how to avoid them. Because Briggs & Stratton does not
necessarily know all the applications this pressure washer could be used for, it is important that you read and understand these instructions thoroughly before attempting to start or
operate this equipment. Save these original instructions for future reference.
This pressure washer requires final assembly before use. Refer to the Assembly section of this manual for instructions on final assembly procedures. Follow the instructions
completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your pressure waher. There are thousands of Briggs & Stratton authorized service dealers worldwide
who provide quality service. You can also find the nearest Authorized Service Dealer in our dealer locator map on the Internet at BRIGGSandSTRATTON.COM.
Table of Contents
Operator Safety ...........................................5
Equipment Description ..........................................................5
Important Safety Information .....................................................5
Assembly ...............................................7
Unpack Pressure Washer ........................................................7
Attach Handle .................................................................7
Install Wheel Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Add Engine Oil ................................................................7
Add Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Lubricate O-Rings..............................................................8
Connect Hose and Water Supply to Pump ...........................................8
Features and Controls.......................................8
Operation ...............................................8
Pressure Washer Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
How to Start Your Pressure Washer ...............................................8
How to Stop Your Pressure Washer................................................9
How to Use Adjustable Nozzle ....................................................9
Applying Detergent.............................................................9
Pressure Washer Rinsing.......................................................10
Cleaning Detergent Siphoning Tube ...............................................10
Automatic Cool Down System (Thermal Relief) ......................................10
Maintenance ............................................10
Maintenance Schedule .........................................................10
Pressure Washer Maintenance...................................................10
Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
After Each Use ...............................................................12
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Long Term Storage............................................................13
Troubleshooting..........................................14
Specifications ...........................................14
Product Specifications .........................................................14
Common Service Parts.........................................................14
Warranties .............................................15
Pressure Washer Owner Warranty ................................................15
Copyright © 2012 Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON POWER PRODUCTS is a registered
trademark of Briggs & Stratton Corporation
Milwaukee, WI, USA
ORIGINAL INSTRUCTIONS
Pressure Washer
Model Number
Revision
Serial Number
Date Purchased
Engine
Model Number
Type Number
Code Number
Not for
Reproduction
5
Operator Safety
Equipment Description
Read this manual carefully and become familiar with your pressure
washer. Know its applications, its limitations and any hazards involved.
This pressure washer operates at 137.9 BARS (2,000 PSI) at a flow rate of 7.2 l
(1.9 gallons) per minute. This high quality residential system features 17.8 cm (7”) wheels,
axial cam pump with stainless steel pistons, automatic cool down system, detergent
siphoning system, adjustable spray nozzle, heavy duty 9.1 m (30’) hose, and more.
Every effort has been made to ensure that the information in this manual is both
accurate and current. However, the manufacturer reserves the right to change, alter or
otherwise improve the product and this documentation at any time without prior notice.
Important Safety Information
The manufacturer cannot possibly anticipate every possible circumstance that might
involve a hazard. The warnings in this manual, and the tags and decals affixed to the
unit are, therefore, not all-inclusive. If you use a procedure, work method or operating
technique that the manufacturer does not specifically recommend, you must satisfy
yourself that it is safe for you and others. You must also make sure that the procedure,
work method or operating technique that you choose does not render the product
unsafe.
Safety Symbols and Meanings
The safety alert symbol indicates a potential personal injury hazard. A signal word
(DANGER, WARNING, or CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol may be used to represent the
type of hazard. The signal word NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazard which, if not avoided, will result in death or serious
injury.
WARNING indicates a hazard which, if not avoided, could result in death or
serious injury.
CAUTION indicates a hazard which, if not avoided, could result in minor or
moderate injury.
NOTICE address practices not related to personal injury.
Warning Tag Figure
1
A warning tag is provided on your unit to inform you of potential safety hazards. If the
tag becomes damaged or illegible, replace it by contacting your local Briggs & Stratton
dealer to obtain a new one.
The icons on the warning tag are shown and described in detail in this section.
WARNING Running engine gives off carbon monoxide, an odorless,
colorless, poison gas.
Breathing carbon monoxide could result in death, serious injury, headache,
fatigue, dizziness, vomiting, confusion, seizures, nausea or fainting.
Some chemicals or detergents could be harmful if inhaled or ingested, resulting in
death, serious injury, nausea, fainting or poisoning.
• OperatethisproductONLYoutdoors.
• Keepexhaustgasfromenteringaconfinedareathroughwindows,doors,
ventilation intakes, or other openings.
• DONOToperatethisproductinsideanybuilding,carport,porch,mobile
equipment, marine applications, or enclosure, even if windows and doors are open.
• Usearespiratorormaskwheneverthereisachancethatvaporsmaybeinhaled
when using chemicals.
• Readallinstructionswithmasksoyouarecertainthemaskwillprovidethe
necessary protection against inhaling harmful vapors when using chemicals.
WARNING Starter cord kickback (rapid retraction) will pull hand and arm
toward engine faster than you can let go which could cause broken
bones, fractures, bruises, or sprains resulting in serious injury.
• NEVERpullstartercordwithoutfirstrelievingspraygunpressure.
• Whenstartingengine,pullcordslowlyuntilresistanceisfeltandthenpullrapidly
to avoid kickback.
• Aftereachstartingattempt,whereenginefailstorun,alwayspointspraygunin
safe direction, press red button and squeeze spray gun trigger to release high
pressure.
• Firmlygraspspraygunwithbothhandswhenusinghighpressurespraytoavoid
injury when spray gun kicks back.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in death, serious injury, and/or
property damage.
• DONOTusecausticliquidwithpressurewasher.
• UseONLYpressurewashersafedetergents/soaps.Followallmanufacturers
instructions.
WARNING Risk of electrocution.
Contact with power source could cause electric shock or burn resulting
in death or serious injury.
• NEVERspraynearpowersource.
Fire
Explosion
Toxic Fumes
Hot Surface
Moving Parts
Electrical Shock
Kickback
Flying Objects
Operator’s Manual
Projectile Chemical Burn
Fluid Injection
Fall Slippery Surface
WARNING Exhaust heat/gases could ignite combustibles, structures or
damage fuel tank causing a fire, resulting in death, serious
injury and/or property damage.
Contact with muffler area could cause burns resulting in
serious injury.
• DONOTtouchhotpartsandAVOIDhotexhaustgases.
• Allowequipmenttocoolbeforetouching.
• Keepatleast1.5m(5ft.)ofclearanceonallsidesofpressurewasherincluding
overhead.
• Contacttheoriginalequipmentmanufacturer,retailer,ordealertoobtainaspark
arrester designed for the exhaust system installed on this engine.
• Replacementpartsmustbethesameandinstalledinthesamepositionasthe
original parts.
WARNING Use of pressure washer could create puddles and slippery surfaces
causing you to fall resulting in death or serious injury.
Kickback from spray gun could cause you to fall resulting in
death or serious injury.
• Operatepressurewasherfromastablesurface.
• Thecleaningareashouldhaveadequateslopesanddrainagetoreducethe
possibility of a fall due to slippery surfaces.
• Beextremelycarefulifyoumustusethepressurewasherfromaladder,
scaffolding, or any other similar location.
• Firmlygraspspraygunwithbothhandswhenusinghighpressurespraytoavoid
injury when spray gun kicks back.
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
NOTICE High pressure spray may damage fragile items including glass.
• DONOTpointspraygunatglasswheninjetspraymode.
• NEVERaimspraygunatplants.
NOTICE Improper treatment of pressure washer could damage it and shorten its life.
• Ifyouhavequestionsaboutintendeduse,askdealerorcontactqualifiedservice
center.
• NEVERoperateunitswithbrokenormissingparts,orwithoutprotectivehousingor
covers.
• DONOTby-passanysafetydeviceonthismachine.
• DONOTtamperwithgovernedspeed.
• DONOToperatepressurewasheraboveratedpressure.
• DONOTmodifypressurewasherinanyway.
• Beforestartingpressurewasherincoldweather,checkallpartsoftheequipmentto
be sure ice has not formed there.
• NEVERmovemachinebypullingonhoses.Usehandleprovidedonunit.
• ThisequipmentisdesignedtobeusedwithBriggs&StrattonPowerProducts
authorized parts ONLY. If equipment is used with parts that DO NOT comply with
minimum specifications, user assumes all risks and liabilities.
WARNING Unintentional sparking could cause fire or electric shock resulting
in death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER
• Disconnectthesparkplugwirefromthesparkplugandplacethewirewhereit
cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Useapprovedsparkplugtester.
• DO NOT check for spark with spark plug removed.
WARNING Starter and other rotating parts could entangle hands, hair,
clothing, or accessories resulting in serious injury.
• NEVERoperatepressurewasherwithoutprotectivehousingorcovers.
• DONOTwearlooseclothing,jewelryoranythingthatcouldbecaughtinthe
starter or other rotating parts.
• Tieuplonghairandremovejewelry.
CAUTION Excessively high operating speeds could result in minor injury
and/or pressure washer damage.
Excessively low speeds impose a heavy load.
• DONOTtamperwithgovernorspring,linksorotherpartstoincreaseengine
speed. Pressure washer supplies correct rated pressure and flow when running at
governed speed.
• DONOTmodifypressurewasherinanyway.
WARNING Fuel and its vapors are extremely flammable and explosive which
could cause burns, fire or explosion resulting in death,
serious injury and/or property damage.
WHEN ADDING OR DRAINING FUEL
• TurnpressurewasherengineOFFandletitcoolatleast2minutesbefore
removing fuel cap. Loosen cap slowly to relieve pressure in tank.
• Fillordrainfueltankoutdoors.
• DONOToverfilltank.Allowspaceforfuelexpansion.
• Iffuelspills,waituntilitevaporatesbeforestartingengine.
• Keepfuelawayfromsparks,openflames,pilotlights,heat,andotherignition
sources.
• Checkfuellines,tank,capandfittingsfrequentlyforcracksorleaks.Replaceif
necessary.
• DONOTlightacigaretteorsmoke.
WHEN STARTING EQUIPMENT
• Ensuresparkplug,muffler,fuelcap,andaircleanerareinplace.
• DONOTcrankenginewithsparkplugremoved.
WHEN OPERATING EQUIPMENT
• DONOToperatethisproductinsideanybuilding,carport,porch,mobile
equipment, marine applications, or enclosure.
• DONOTtipengineorequipmentatanglewhichcausesfueltospill.
• DONOTsprayflammableliquids.
WHEN TRANSPORTING, MOVING OR REPAIRING EQUIPMENT
• Transport/move/repairwithfueltankEMPTYorwithfuelshutoffvalveOFF.
• DONOTtipengineorequipmentatanglewhichcausesfueltospill.
• Disconnectsparkplugwire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK
• Storeawayfromfurnaces,stoves,waterheaters,clothesdryers,orother
appliances that have pilot light or other ignition source because they could ignite
fuel vapors.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Ifcutbyfluid,callphysicianimmediately.DONOTtreatasasimplecut.
• DONOTallowCHILDRENtooperatepressurewasher.
• NEVERrepairhighpressurehose.Replaceit.
• NEVERrepairleakingconnectionswithsealantofanykind.Replaceo-ringorseal.
• NEVERconnecthighpressurehosetonozzleextension.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• ALWAYSpointsprayguninsafedirection,pressredbuttonandsqueezespray
gun trigger to release high pressure, every time you stop engine.
• NEVERaimspraygunatpeople,animals,orplants.
• DONOTsecuresprayguninopenposition.
• DONOTleavespraygununattendedwhilemachineisrunning.
• NEVERuseaspraygunwhichdoesnothaveatriggerlockortriggerguardin
place and in working order.
• Alwaysbecertainspraygun,nozzlesandaccessoriesarecorrectlyattached.
WARNING Risk of eye or bodily injury.
Spray could splash back or propel objects resulting in serious
injury.
• Alwayswearindirectvented(chemicalsplash)safetygogglesmarkedtocomply
with ANSI Z87.1 when using or in vicinity of this equipment.
• NEVERsubstitutesafetyglassesordry-conditiongogglesforindirectvented
safety goggles.
• Alwayswearprotectiveclothingsuchasalong-sleevedshirt,longpantsand
close-toed shoes.
• NEVERoperatepressurewasherwhenbarefootorwearingsandalsorshorts.
Not for
Reproduction
7
Assembly
Read entire Operator’s Manual before you attempt to assemble or operate
your new pressure washer.
Your pressure washer requires some assembly and is ready for use after it has been
properly serviced with the recommended oil and fuel.
If you have any problems with the assembly of your pressure washer, contact your local
Briggs & Stratton service center. If you need assistance, please have the model, revision,
and serial number from the identification label available. See Features and Controls for
identification label location.
Unpack Pressure Washer
1. Set the carton on a rigid, flat surface.
2. Remove the parts bag, accessories, and inserts included with pressure washer.
3. Open carton completely by cutting each corner from top to bottom.
4. Ensure you have all included items prior to assembly.
Items in the carton include:
• MainUnit
• Handle
• HighPressureHose
• SprayGun
• AdjustableNozzleExtension
• Wheels(2)
• PartsBag(whichincludesthefollowing):
• Operator’sManual
• HoseFittings
• MaintenanceKit
• AccessoryStorageBag
• Handle/WheelKitFasteningHardwareKit(whichincludes):
• CarriageBolts(2)
• PlasticKnobs(2)
• AxlePins(2)
• RetainingPins(2)
To prepare your pressure washer for operation, you will need to perform these tasks:
1. Attach handle and wheel kit to main unit.
2. Add oil to engine crankcase.
3. Add fuel to fuel tank.
4. Connect high pressure hose to spray gun and pump.
5. Connect water supply to pump.
6. Attach nozzle extension to spray gun.
Attach Handle Figure
2
1. Place handle (A) onto base (B). Make sure holes in handle align with holes on
base.
2. Insert carriage bolts (C) through holes from outside of unit and attach a plastic
knob (D) from inside of unit. Tighten by hand.
Install Wheel Kit Figure
3
The wheel kit is designed to greatly improve the portability of your pressure washer.
NOTICE Wheel kit is not intended for over-the-road use.
Install the wheel kit as follows:
1. Place the bottom of the pressure washer frame on a flat, even surface.
2. Slide a wheel (A) over the axle pin (B).
NOTICE Be sure to install wheel with raised hub inboard.
3. Slide axle pin through hole (C) in frame.
4. Retain wheel on axle pin with retaining pin (D).
5. Repeat step 2 through 4 to secure second wheel.
Add Engine Oil
1. Place pressure washer on a level surface.
2. Add engine oil as described in Adding Engine Oil of the Engine Maintenance
section.
NOTICE
Improper treatment of pressure washer could damage it and shorten its life.
• DONOTattempttocrankorstarttheenginebeforeithasbeenproperlyserviced
with the recommended oil. This could result in an engine failure.
Add Fuel Figure
4
Fuel must meet these requirements:
• Clean,fresh,unleadedpetrol.
• Aminimumof87octane/87AKI(91RON).Forhighaltitudeuse,seeHigh
Altitude.
• Petrolwithupto10%ethanol(gasohol)orupto15%MTBE(methyltertiary
butyl ether) is acceptable.
NOTICE Avoid pressure washer damage.
Failure to follow Operator’s Manual for fuel recommendations voids warranty.
• DONOTuseunapprovedpetrolsuchasE85.
• DONOTmixoilinpetrol.
• DONOTmodifyenginetorunonalternatefuels.
To protect the fuel system from gum formation, mix in a fuel stabilizer when adding fuel.
See Storage. All fuel is not the same. If you experience starting or performance problems
after using fuel, switch to a different fuel provider or change brands. This engine is
certified to operate on petrol. The emission control system for this engine is EM (Engine
Modifications).
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel tank (B). Be careful not to overfill.
Allow about 4 cm (1.5”) (C) of tank space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate before starting engine.
High Altitude
Ataltitudesover1500meters(5,000feet),aminimum85octane/85AKI(89
RON) petrol is acceptable. To remain emissions compliant, high altitude adjustment
is required. Operation without this adjustment will cause decreased performance,
increased fuel consumption, and increased emissions. See a Briggs & Stratton
Authorized Dealer for high altitude adjustment information. Operation of the engine at
altitudes below 750 meters (2,500 feet) with the high altitude kit is not recommended.
Lubricate O-Rings Figure
5
Lubrication of o-rings is extremely important for installation and operation. The use
of a lubricant (petroleum or synthetic grease) during assembly helps seat o-rings
properly and provides an improved seal. It also helps protect the o-ring from damage
by abrasion, pinching or cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant on o-rings prior to assembling
the garden hose to the pump (A), high pressure hose threaded end (B), spray gun (C),
andhighpressurehosequickconnectend(D).
Lubricate all connections shown below, following these instructions:
1. Inspect and clean connecting surfaces prior to lubrication and assembly.
2. Use lubricants sparingly during assembly; a light film is all that is required.
3. Use a small brush or cotton swab to apply grease directly to o-rings where they
are not accessible (QC fitting, M22 fitting).
WARNING Fuel and its vapors are extremely flammable and explosive which
could cause burns, fire or explosion resulting in death, serious
injury and/or property damage.
WHEN ADDING FUEL
• TurnpressurewasherengineOFFandletitcoolatleast2minutesbefore
removing fuel cap. Loosen cap slowly to relieve pressure in tank.
• Fillfueltankoutdoors.
• DONOToverfilltank.Allowspaceforfuelexpansion.
• Iffuelspills,waituntilitevaporatesbeforestartingengine.
• Keepfuelawayfromsparks,openflames,pilotlights,heat,andotherignition
sources.
• Checkfuellines,tank,capandfittingsfrequentlyforcracksorleaks.Replaceif
necessary.
• DONOTlightacigaretteorsmoke.
Not for
Reproduction
Connect Hose and Water Supply to Pump Figure
6
7
8
9
NOTICE DO NOT run the pump without the water supply connected and turned on.
• Damagetoequipmentresultingfromfailuretofollowthisinstructionwillvoid
warranty.
NOTICE Remove and discard the shipping caps from the pump’s high pressure outlet
and water inlet before attaching hoses.
1. Uncoil high pressure hose and attach one end of hose to base of spray gun (6).
Pull back on collar of quick connect, slide fitting onto spray gun and let go of
collar. Pull on hose to be sure of a tight connection.
2. Attach other end of high pressure hose to high pressure outlet on pump (7).
Tighten by hand.
3. Run water through your garden hose for 30 seconds to clean out any debris.
NOTICE DO NOT siphon standing water for the water supply. Use ONLY cold water
(less than 38°C (100°F)).
4. Before connecting garden hose to water inlet, inspect inlet screen (8,A).
Clean screen if it contains debris or have it replaced if damaged. DO NOT run
pressure washer if inlet screen is damaged.
NOTICEUsingaOneWayValve(vacuumbreakerorcheckvalve)atpumpinlet
could cause pump or inlet connector damage.
• ThereMUSTbeatleasttenfeetofunrestrictedgardenhosebetweenthepressure
washer inlet and any device, such as a vacuum breaker or check valve.
• Damagetoequipmentresultingfromfailuretofollowthisinstructionwillvoid
warranty.
5. Connect the garden hose (not to exceed 15 m (50 ft.) in length) to the water
inlet (8). Tighten by hand.
6. Turn ON the water, press red button (9,A) on the gun and squeeze the trigger
to purge the pump system of air and impurities.
Checklist Before Starting Engine
Review the unit’s assembly to ensure you have performed all of the following.
1. Be sure to read Operator Safety and Operation sections before using pressure
washer.
2. Make sure handle is in place and secure.
3. Check that oil has been added to proper level in the engine crankcase.
4. Add proper fuel to fuel tank.
5. Check for properly tightened hose connections.
6. Check to make sure there are no kinks, cuts, or damage to high pressure hose.
7. Provide a proper water supply at an adequate flow.
Features and Controls Figure
10
Read this Operator’s Manual and safety rules before operating your
pressure washer. Compare the illustrations with your pressure washer, to
familiarize yourself with the locations of various controls and adjustments.
Save this manual for future reference.
A - Recoil Starter — Used for starting the engine manually.
B - Oil Fill/Dipstick — Check, fill and drain oil here.
C - Pump — Develops high pressure.
D - Automatic Cool Down System — Cycles water through pump when water reaches
51°C-68°C (125°-155°F). Warm water will discharge from pump onto ground. This
system prevents internal pump damage.
E - High Pressure Hose — Connect one end to water pump and other end to spray gun.
F - Spray Gun — Controls the application of water onto cleaning surface with trigger
device. Includes trigger lock.
G - Adjustable Nozzle — Always attached to nozzle extension. Adjustable nozzle allows
you to adjust spray pressure and spray pattern.
H - Fuel Tank — Fill tank with regular unleaded fuel. Always leave room for fuel expansion.
Items Not Shown:
Air Filter — Protects engine by filtering dust and debris out of intake air.
Detergent Siphoning Tube — Use to siphon pressure washer safe detergent into the
low pressure stream.
Identification Label (near rear of base plate) — Provides model and serial number of
pressure washer. Please have these readily available if calling for assistance.
High Pressure Outlet — Connection for high pressure hose.
Primer Bulb — Prepares a cold engine for starting.
Throttle Lever — Sets engine in starting mode for recoil starter and stops a running
engine.
Water Inlet — Connection for garden hose.
Operation
Pressure Washer Location Figure
11
Clearances and Air Movement
Place pressure washer outdoors in an area that will not accumulate deadly exhaust
gas. DO NOT place pressure washer where exhaust gas (A) could accumulate and enter
inside or be drawn into a potentially occupied building. Ensure exhaust gas is kept
away from any windows, doors, ventilation intakes, or other openings that can allow
exhaust gas to collect in a confined area. Prevailing winds and air currents should be
taken into consideration when positioning pressure washer.
How to Start Your Pressure Washer Figure
12
13
14
To start your pressure washer for the first time, follow these instructions step-by-step.
This starting information also applies if you have let the pressure washer sit idle for at
least a day.
1. Place pressure washer near an outside water source capable of supplying water
at a flow rate greater than 11.0 l (2.9 gallons) per minute and no less than 1.38
BARS (20 PSI) at pressure washer end of garden hose. DO NOT siphon supply
water.
2. Check that high pressure hose is tightly connected to spray gun and pump. See
Assembly section.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure washer pump.
NOTICE DO NOT run the pump without the water supply connected and turned on.
• Damagetoequipmentresultingfromfailuretofollowthisinstructionwillvoidwarranty.
5. Turn ON water, point gun in a safe direction, press red button and squeeze
trigger to purge pump system of air and impurities.
6. Attach nozzle extension to spray gun (12). Tighten by hand.
7. Move throttle lever (13,A) to the Fast position, shown as a rabbit (
).
To start the engine for the very first time:
8A. Push primer bulb firmly 5 times, waiting 2 seconds between each push.
To start engine thereafter:
8B. Press primer bulb firmly 3 times, waiting 2 seconds between each push. For a
warm engine, DO NOT press primer bulb.
8 BRIGGSandSTRATTON.COM
WARNING Exhaust heat/gases could ignite combustibles, structures or
damage fuel tank causing a fire, resulting in death, serious injury and/or
property damage.
• Keepatleast1.5m(5ft.)clearanceonallsidesofpressurewasherincluding
overhead.
WARNING Running engine gives off carbon monoxide, an odorless,
colorless, poison gas.
Breathing carbon monoxide could result in death, serious injury, headache,
fatigue, dizziness, vomiting, confusion, seizures, nausea or fainting.
• OperatethisproductONLYoutdoors.
• Keepexhaustgasfromenteringaconfinedareathroughwindows,doors,
ventilation intakes, or other openings.
• DONOToperatethisproductinsideanybuilding,carport,porch,mobile
equipment, marine applications, or enclosure, even if windows and doors are open.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVERconnecthighpressurehosetonozzleextension.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• Alwaysbecertainspraygun,nozzlesandaccessoriesarecorrectlyattached.
WARNING Risk of eye injury.
Spray could splash back or propel objects resulting in serious injury.
• Alwayswearindirectvented(chemicalsplash)safetygogglesmarkedtocomply
with ANSI Z87.1 when using or in vicinity of this equipment.
• NEVERsubstitutesafetyglassesordry-conditiongogglesforindirectvented
safety goggles.
Not for
Reproduction
9
NOTICE Before starting the pressure washer, be sure you are wearing adequate safety
goggles as described below.
9. When starting engine, position yourself as recommended (14), grasp starter
grip handle and pull slowly until you feel some resistance. Then pull rapidly to
start engine.
10. Return starter grip handle slowly. DO NOT let rope “snap back” against starter.
NOTICE Always keep the throttle lever in the Fast (
) position when operating the
pressure washer.
How to Stop Your Pressure Washer
1. Release spray gun trigger and let engine idle for two minutes.
2. Move throttle lever to Slow (
) position, then Stop ( ) position.
3. ALWAYS point gun in a safe direction, press red button and squeeze spray gun
trigger to release retained high water pressure.
How to Use the Adjustable Nozzle Figure
15
16
17
You should now know how to START and STOP your pressure washer. The information
in this section will tell you how to adjust the spray pattern and to apply pressure
washer specific detergents.
1. Slide nozzle backward (15,A) to achieve high pressure. Slide nozzle forward
(15,B) when you wish to adjust spray to low pressure mode.
2. Point nozzle down toward a firm surface and press trigger to test pattern (16).
3. Twisting nozzle adjusts spray pattern from a fan pattern (17,A) to a narrow
pattern (17,B).
Usage Tips
• Formosteffectivecleaning,keepspraynozzlefrom20to61cm(8to24in.)
away from cleaning surface.
• Ifyougetspraynozzletooclose,especiallyusinghighpressuremode,youmay
damage surface being cleaned.
• DO NOT get closer than 15 cm (6 in) when cleaning tires.
Applying Detergent
To apply detergent, follow these steps:
1. Review use of adjustable nozzle.
2. Prepare detergent solution as required by job.
3. Place end of detergent siphoning tube into detergent container.
NOTICE Make sure the tube is fully submerged in detergent while applying detergent.
NOTICE Contact with the hot muffler could damage detergent siphoning tube.
• Wheninsertingthesiphonintoadetergentsolutionbottle,routethetubesoasto
keep it from inadvertently contacting the hot muffler.
4. Slide nozzle forward to low pressure mode. Detergent cannot be applied with
nozzle in high pressure position.
5. Make sure garden hose is connected to water inlet. Check that high pressure
hose is connected to spray gun and pump. Turn on water.
NOTICE You must attach all hoses before you start the engine.
• StartingtheenginewithoutallthehosesconnectedandwithoutthewaterturnedON
could damage the pump.
• Damagetoequipmentresultingfromfailuretofollowthisinstructionwillvoid
warranty.
6. Start engine following instructions How to Start Your Pressure Washer.
7. Apply detergent to a dry surface, starting at lower portion of area to be washed
and work upward, using long, even, overlapping strokes.
8. Allow detergent to “soak in” for 3-5 minutes before washing and rinsing.
Reapply as needed to prevent surface from drying. DO NOT allow detergent to
dry on (prevents streaking).
NOTICE You must flush the detergent siphoning system after each use by placing the
tube into a bucket of clean water, then run the pressure washer in low pressure for 1-2
minutes.
WARNING Exhaust heat/gases could ignite combustibles, structures or
damage fuel tank causing a fire, resulting in death, serious
injury and/or property damage.
Contact with muffler area could cause burns resulting in
serious injury.
• DONOTtouchhotpartsandAVOIDhotexhaustgases.
• Allowequipmenttocoolbeforetouching.
• Keepatleast1.5m(5ft.)ofclearanceonallsidesofpressurewasherincluding
overhead.
• Contacttheoriginalequipmentmanufacturer,retailer,ordealertoobtainaspark
arrester designed for the exhaust system installed on this engine.
• Replacementpartsmustbethesameandinstalledinthesamepositionasthe
original parts.
WARNING Risk of eye injury.
Spray could splash back or propel objects resulting in serious injury.
• Alwayswearindirectvented(chemicalsplash)safetygogglesmarkedtocomply
with ANSI Z87.1 when using or in vicinity of this equipment.
• NEVERsubstitutesafetyglassesordry-conditiongogglesforindirectvented
safety goggles.
WARNING Starter cord kickback (rapid retraction) will pull hand and arm
toward engine faster than you can let go which could cause broken
bones, fractures, bruises, or sprains resulting in serious injury.
• NEVERpullstartercordwithoutfirstrelievingspraygunpressure.
• Whenstartingengine,pullcordslowlyuntilresistanceisfeltandthenpullrapidly
to avoid kickback.
• Aftereachstartingattempt,whereenginefailstorun,alwayspointspraygunin
safe direction, press red button and squeeze spray gun trigger to release high
pressure.
• Firmlygraspspraygunwithbothhandswhenusinghighpressurespraytoavoid
injury when spray gun kicks back.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• DONOTallowCHILDRENtooperatepressurewasher.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• NEVERaimspraygunatpeople,animals,orplants.
• DONOTsecuresprayguninopenposition.
• DONOTleavespraygununattendedwhilemachineisrunning.
• NEVERuseaspraygunwhichdoesnothaveatriggerlockortriggerguardin
place and in working order.
• Alwaysbecertainspraygun,nozzlesandaccessoriesarecorrectlyattached.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVERadjustspraypatternwhenspraying.
• NEVERputhandsinfrontofnozzletoadjustspraypattern.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in death, serious injury, and/or
property damage.
• DONOTusecausticliquidwithpressurewasher.
• UseONLYpressurewashersafedetergents/soaps.Followallmanufacturers
instructions.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• ALWAYSpointsprayguninsafedirection,pressredbuttonandsqueezespray
gun trigger to release high pressure, every time you stop engine.
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
Pressure Washer Rinsing
For Rinsing:
1. Slide the nozzle backward to high pressure, press the trigger and wait for the
detergent to clear.
NOTICE You can also stop detergent from flowing by simply removing detergent
siphoning tube from bottle.
2. Keep the spray gun a safe distance from the area you plan to spray.
3. Apply a high pressure spray to a small area, then check the surface for damage.
If no damage is found, it is okay to continue cleaning.
4. Start at the top of the area to be rinsed, working down with same overlapping
strokes as you used for washing and applying detergent.
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must flush it with clean water before
stopping the engine.
1. Place detergent siphoning tube in a bucket full of clean water.
2. Slide adjustable nozzle forward to low pressure position.
3. Flush for 1-2 minutes.
4. Shut off engine following instructions How to Stop Pressure Washer and turn
off water supply.
5. ALWAYS point gun in a safe direction, press red button and squeeze spray gun
trigger to release retained high water pressure.
Automatic Cool Down System (Thermal Relief)
If you run the engine on your pressure washer for 3-5 minutes without pressing the
trigger on the spray gun, circulating water in the pump can reach temperatures above
52°C (125°F). The system engages to cool the pump by discharging the warm water
onto the ground.
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever occurs first. More frequent service is
required when operating in adverse conditions noted below.
1
Clean if clogged. Replace if perforated or torn.
2
Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance and extend the life of the pressure
washer. See any authorized dealer for service.
The pressure washer’s warranty does not cover items that have been subjected to
operator abuse or negligence. To receive full value from the warranty, the operator
must maintain the pressure washer as instructed in this manual, including proper
storage as detailed in Winter Storage and Long Term Storage.
NOTICE Should you have questions about replacing components on your pressure
washer, please visit our website at BRIGGSandSTRATTON.COM.
Some adjustments will need to be made periodically to properly maintain your pressure
washer.
All service and adjustments should be made at least once each season. Follow the
requirements in the Maintenance Schedule chart above.
NOTICE Once a year you should clean or replace the spark plug, clean or replace the
air filter, and check the spray gun and nozzle extension assembly for wear. A new spark
plug and clean air filter assure proper fuel-air mixture and help your engine run better
and last longer.
Pump Oil
DO NOT attempt any oil maintenance on this pump. The pump is pre-lubricated and
sealed from the factory, requiring no additional maintenance for the life of the pump.
Before Each Use
1. Check engine oil level.
2. Clean debris.
3. Check water inlet screen for damage.
4. Check high pressure hose for leaks.
5. Check detergent siphoning tube for damage.
6. Check spray gun and nozzle extension assembly for leaks.
7. Rinse out garden hose to flush out debris.
Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from pressure washer. Keep linkage,
spring and controls clean. Keep area around and behind muffler free from any
combustible debris. Inspect cooling air slots and openings on the pressure washer.
These openings must be kept clean and unobstructed.
WARNING Kickback from spray gun could cause you to fall resulting in
death or serious injury.
• Operatepressurewasherfromastablesurface.
• Beextremelycarefulifyoumustusethepressurewasherfromaladder,
scaffolding, or any other similar location.
• Firmlygraspspraygunwithbothhandswhenusinghighpressurespraytoavoid
injury when spray gun kicks back.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• ALWAYSpointsprayguninsafedirection,pressredbuttonandsqueezespray
gun trigger to release high pressure, every time you stop engine.
First 5 Hours
• Changeengineoil
Every 8 Hours or Daily
• Check/cleanwaterinletscreen
1
• Checkhighpressurehose
• Checkdetergentsiphoningtube
• Checkspraygunandassemblyforleaks
• Cleandebris
• Checkengineoillevel
Every 25 Hours or Yearly
• Serviceengineaircleaner
2
Every 50 Hours or Yearly
• Changeengineoil
2
• Inspectmufflerandsparkarrester
Every 100 Hours or Yearly
• Servicesparkplug
• Cleancoolingsystem
2
Not for
Reproduction
11
Pressure washer parts should be kept clean to reduce the risk of overheating and
ignition of accumulated debris.
• Useadampclothtowipeexteriorsurfacesclean.
NOTICE Improper treatment of pressure washer could damage it and shorten its life.
• DONOTinsertanyobjectsthroughcoolingslots.
• Useasoftbristlebrushtoloosencakedondirt,oil,etc.
• Useavacuumcleanertopickuploosedirtanddebris.
Check and Clean Inlet Screen
Examine the screen on the pump’s water inlet. Clean it if the screen is clogged or
replace it if screen is damaged.
Check High Pressure Hose
The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the
hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover,
damage or movement of couplings. If any of these conditions exist, replace the hose
immediately.
Check Detergent Siphoning Tube
Examine the detergent tube and clean if clogged. The tube should fit tightly on the
barbed fitting. Examine the tube for leaks or tears. Replace the tube if damaged.
Detergent Siphoning Check Ball
Occasionally check ball in detergent siphoning system may become stuck from
storage, dried soap, or minerals in water. The check ball can be freed by performing
thefollowing:
NOTICE Before performing this procedure, be sure you are wearing safety goggles as
described below.
1. Shut off engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction, press red button and squeeze
spray gun trigger to release retained high water pressure.
3. Remove detergent siphoning hose from barbed fitting on pump.
4. Using a firm, blunt object 2 mm (7/64”) in diameter or smaller, by at least 2.5
cm (1”) long, such as an Allen wrench, slowly insert the object into the barbed
fitting until you meet resistance. This resistance is the check ball.
5. Slowly push down until you feel the ball move slightly, push no more than 3
mm (1/8”). Slight pressure may be required to free the ball.
6. Repeat steps 4 and 5 if necessary.
7. Reinstall detergent siphoning hose onto barb fitting.
8. Treat with PumpSaver as described in Protecting the Pump during storage to
prevent reoccurrence.
Check Spray Gun
Examine the hose connection to the spray gun and make sure it is secure. Test the
trigger by pressing the red button and making sure the trigger “springs back” into
place when you release it. You should not be able to press the trigger without pressing
the red button. Replace spray gun immediately if it fails any of these tests.
Nozzle Maintenance
Figure
18
19
20
A pulsing sensation felt while squeezing the spray gun trigger may be caused by
excessive pump pressure. The principal cause of excessive pump pressure is an orifice
clogged or restricted with foreign materials, such as dirt, etc. To correct the problem,
immediately clean the orifice using the tools included with your pressure washer and
followtheseinstructions:
1. Shut off engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction, press red button and squeeze
spray gun trigger to release retained high water pressure.
3. Remove nozzle extension from spray gun.
4. Twist nozzle clockwise to stream position. Using 2 mm allen wrench, remove
orifice (18,A) from end of nozzle extension.
5. Use wire (or small paper clip) to free any foreign material clogging or
restricting orifice (19,A).
6. Using a garden hose, remove additional debris by back flushing water through
nozzle extension (20). Back flush between 30 to 60 seconds. Turn adjustable nozzle
extension to stream spray and move nozzle from low to high while flushing.
7. Reinstall orifice into nozzle extension. DO NOT overtighten orifice with allen
wrench.
8. Reconnect nozzle extension to spray gun.
9. Make sure garden hose is connected to water inlet. Check that high pressure
hose is connected to spray gun and pump. Turn on water.
10. Start engine following instructions How to Start Your Pressure Washer.
11. Test pressure washer by operating with nozzle in high and low positions.
O-Ring Maintenance
Through the normal operation of your pressure washer, o–rings are used to keep
the connections of the hoses and spray gun tight and leak–free. These o-rings may
become worn or damaged.
An O–Ring Maintenance Kit is provided with your pressure washer which includes
replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet
provided in the kit to service your unit’s o-rings. Note that you will not use all of the
parts in the kit.
To remove a worn or damaged o–ring, use a small flathead screwdriver to get
underneath the o-ring and pry it off.
Engine Maintenance
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVERrepairhighpressurehose.Replaceit.
• ReplacementhoseratingMUSTequalorexceedmaximumpressureratingofunit.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• ALWAYSpointsprayguninsafedirection,pressredbuttonandsqueezespray
gun trigger to release high pressure, every time you stop engine.
WARNING Risk of eye injury.
Spray could splash back or propel objects resulting in serious injury.
• Alwayswearindirectvented(chemicalsplash)safetygogglesmarkedtocomply
with ANSI Z87.1 when using or in vicinity of this equipment.
• NEVERsubstitutesafetyglassesordry-conditiongogglesforindirectvented
safety goggles.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• ALWAYSpointsprayguninsafedirection,pressredbuttonandsqueezespray
gun trigger to release high pressure, every time you stop engine.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVERrepairleakingconnectionswithsealantofanykind.Replaceo-ringorseal.
WARNING Unintentional sparking could cause fire or electric shock resulting
in death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER
• Disconnectthesparkplugwirefromthesparkplugandplacethewirewhereit
cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Useapprovedsparkplugtester.
• DO NOT check for spark with spark plug removed.
Not for
Reproduction
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty Certified oils for best
performance. Other high-quality detergent oils are acceptable if classified for service
SF, SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart
to select the best viscosity for the outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil consumption. Check
oil level more frequently.
Checking Oil Level
Figure
21
Oil level should be checked prior to each use or at least every 8 hours of operation.
Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean cloth. Replace and tighten
dipstick. Remove and check oil level.
3. VerifyoilisatFullmark(tophole)(A) on dipstick. Replace and tighten dipstick.
Adding Engine Oil
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in Checking Oil Level.
3. If needed, slowly pour oil into oil fill opening to the Full mark (top hole) on
dipstick. DO NOT overfill.
NOTICE Overfilling with oil could cause the engine to not start, or hard starting.
• DONOToverfill.
• IfovertheFullmarkondipstick,drainoiltoreduceoilleveltoFullmarkondipstick.
4. Replace and tighten dipstick.
Changing Engine Oil
If you are using your pressure washer under extremely dirty or dusty conditions, or in
extremely hot weather, change the oil more often.
KEEPOUTOFREACHOFCHILDREN.DON’TPOLLUTE.CONSERVE
RESOURCES. RETURN USED OIL TO COLLECTION CENTERS.
Change the oil while the engine is still warm from running, as follows:
1. Drain fuel tank by running pressure washer until fuel tank is empty.
2. Disconnect spark plug wire and keep it away from spark plug.
3. Clean area around oil fill, remove oil fill cap/dipstick. Wipe dipstick clean.
4. Tip your pressure washer to drain oil from oil fill into a suitable container
making sure you tip your unit away from spark plug. When crankcase is empty,
return pressure washer to upright position.
5. Repeat steps 3 and 4 to add engine oil as described in Adding Engine Oil.
6. Wipe up any remaining oil.
7. Reconnect spark plug wire to spark plug.
Service Air Cleaner
Figure
22
Your engine will not run properly and may be damaged if you run it with a dirty air
cleaner. Service more often if operating under dirty or dusty conditions.
To service the air cleaner, follow these steps:
1. Remove screw (A).
2. Carefully remove air cleaner assembly to prevent debris from falling into
carburetor.
3. Take air cleaner assembly apart and clean all parts. Wash foam air cleaner (B)
in liquid detergent and water. Squeeze dry in a clean cloth.
4. SATURATE foam air cleaner in engine oil and squeeze in a clean cloth to
remove excess oil.
5. Reinstall clean or new foam air cleaner in base (C).
6. Install air cleaner securely on carburetor with screw.
Service Spark Plug
Figure
23
Changing the spark plug will help your engine to start easier and run better.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
3. Replace spark plug if electrodes are pitted, burned or porcelain is cracked. Use
the recommended replacement plug. See Specifications.
4. Check electrode gap with wire feeler gauge and reset spark plug gap to
recommended gap if necessary (see Specifications).
5. Install spark plug and tighten firmly.
Inspect Muffler and Spark Arrester
Inspect the muffler for cracks, corrosion, or other damage. Remove the spark arrester,
if equipped, and inspect for damage or carbon blockage. If replacement parts are
required, make sure to use only original equipment replacement parts.
Air Cooling System
Figure
24
Over time debris may accumulate in cylinder cooling fins and cannot be observed
without partial engine disassembly. For this reason, we recommend you have an
authorized Briggs & Stratton service dealer clean the cooling system per recommended
intervals (see Maintenance Schedule in beginning of Maintenance section). Equally
important is to keep top of engine free from debris. See Clean Debris.
Carburetor Adjustment
The carburetor on this engine is low emission. It is equipped with a non-adjustable idle
mixture valve. Top speed has been set at the factory. If adjustment is required, see an
authorized service dealer.
After Each Use
Water should not remain in the unit for long periods of time. Sediments or minerals
can deposit on pump parts and freeze pump action. Follow these procedures after
everyuse:
1. Shut off engine, turn off water supply, point gun in a safe direction, press red
button and squeeze trigger to relieve trapped pressure, and let engine cool.
12 BRIGGSandSTRATTON.COM
CAUTION Avoid prolonged or repeated skin contact with used motor oil.
• Usedmotoroilhasbeenshowntocauseskincancerincertainlaboratory
animals.
• Thoroughlywashexposedareaswithsoapandwater.
WARNING Exhaust heat/gases could ignite combustibles, structures or
damage fuel tank causing a fire, resulting in death, serious
injury and/or property damage.
Contact with muffler area could cause burns resulting in
serious injury.
• DONOTtouchhotpartsandAVOIDhotexhaustgases.
• Allowequipmenttocoolbeforetouching.
• Keepatleast1.5m(5ft.)ofclearanceonallsidesofpressurewasherincluding
overhead.
• Contacttheoriginalequipmentmanufacturer,retailer,ordealertoobtainaspark
arrester designed for the exhaust system installed on this engine.
• Replacementpartsmustbethesameandinstalledinthesamepositionasthe
original parts.
CAUTION Excessively high operating speeds could result in minor injury
and/or pressure washer damage.
Excessively low speeds impose a heavy load.
• DONOTtamperwithgovernorspring,linksorotherpartstoincreaseengine
speed. Pressure washer supplies correct rated pressure and flow when running at
governed speed.
• DONOTmodifypressurewasherinanyway.
Not for
Reproduction
13
2. Disconnect hose from spray gun and high pressure outlet on pump. Drain
water from hose, spray gun, and nozzle extension. Use a rag to wipe off the
hose.
3. Empty pump of all pumped liquids by pulling recoil handle about six times. This
should remove most liquid in pump.
4. Store unit in a clean, dry area.
5. If storing for more than 30 days, see Long Term Storage on next page.
Winter Storage
NOTICE You must protect your unit from freezing temperatures.
• Failuretodosowillpermanentlydamageyourpumpandrenderyourunit
inoperable.
• Freezedamageisnotcoveredunderwarranty.
To protect the unit from freezing temperatures:
1. Follow steps 1-3 in the previous section After Each Use.
2. Use pump saver, Model 6039, to treat pump. This minimizes freeze damage
and lubricates pistons and seals.
3. If pump saver is not available, connect a 3 ft. (1 m) section of garden hose to
waterinletadapter.PourRV-antifreeze(antifreezewithoutalcohol)intohose.
Pull recoil handle twice. Disconnect 3 ft. (1 m) hose.
4. Store unit in a clean, dry area.
Long Term Storage
If you do not plan to use the pressure washer for more than 30 days, you must prepare
the engine and pump for long term storage.
Protect Fuel System
Fuel Additive:
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum
deposits to form in the fuel system or on essential carburetor parts. To keep fuel
fresh, use Briggs & Stratton® Advanced Formula Fuel Treatment & Stabilizer, available
wherever Briggs & Stratton genuine service parts are sold.
For engines equipped with a FRESH START® fuel cap, use Briggs & Stratton FRESH
START® available in a drip concentrate cartridge.
There is no need to drain gasoline from the engine if a fuel stabilizer is added
according to instructions. Run the engine for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained
into an approved container. Run the engine until it stops from lack of fuel. The use of a
fuel stabilizer in the storage container is recommended to maintain freshness.
Change Oil
While engine is still warm, drain oil from crankcase. Refill with recommended grade.
See Changing Engine Oil in Engine Maintenance.
Protecting the Pump
To protect the pump from damage caused by mineral deposits or freezing, use
PumpSaver, Model 6039, to treat pump. This prevents freeze damage and lubricates
pistons and seals.
NOTICE PumpSaver is available as an optional accessory. It is not included with
the pressure washer. Contact the nearest authorized service center to purchase
PumpSaver.
NOTICE You must protect your unit from freezing temperatures.
• Failuretodosowillpermanentlydamageyourpumpandrenderyourunit
inoperable.
• Freezedamageisnotcoveredunderwarranty.
To use PumpSaver, make sure the pressure washer is turned off and disconnected
from supply water. Read and follow all instructions and warnings given on the
PumpSaver container.
Other Storage Tips
1. DO NOT store fuel from one season to another unless it has been treated as
described in Protect Fuel System.
2. Replace fuel container if it starts to rust. Rust and/or dirt in fuel can cause
problems if it’s used with this unit.
3. Cover unit with a suitable protective cover that does not retain moisture.
4. Store unit in a clean and dry area.
WARNING Storage covers could cause a fire resulting in death, serious
injury and/or property damage.
• DONOTplaceastoragecoveroverahotpressurewasher.
• Letequipmentcoolforasufficienttimebeforeplacingthecoverontheequipment.
WARNING The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Keephighpressurehoseconnectedtopumpandspraygunwhilesystemis
pressurized.
• ALWAYSpointsprayguninsafedirection,pressredbuttonandsqueezespray
gun trigger to release high pressure, every time you stop engine.
WARNING Fuel and its vapors are extremely flammable and explosive which
could cause burns, fire or explosion resulting in death, serious
injury and/or property damage.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK
• Storeawayfromfurnaces,stoves,waterheaters,clothesdryersorother
appliances that have pilot light or other ignition source because they could ignite
fuel vapors.
Not for
Reproduction
14 BRIGGSandSTRATTON.COM
Troubleshooting
Problem Cause Correction
Pump has following problems: failure
to produce pressure, erratic pressure,
chattering, loss of pressure, low water
volume.
1. Nozzle in low pressure mode.
2. Water inlet is blocked.
3. Inadequate water supply.
4. Inlet hose is kinked or leaking.
5. Clogged inlet hose screen.
6. Water supply is over 100°F (38°C).
7. High pressure hose is blocked or leaks.
8. Gun leaks.
9. Orifice is obstructed.
10. Pump is faulty.
1. Pull nozzle backward for high pressure mode.
2. Clear inlet.
3. Provide adequate water flow.
4. Straighten inlet hose, patch leak.
5. Check and clean inlet hose screen.
6. Provide cooler water supply.
7. Clear blocks in outlet hose.
8. Replace gun.
9. Clean orifice.
10. Contact local service facility.
Detergent fails to mix with spray.
1. Detergent siphoning tube is not submerged.
2. Detergent siphoning tube is clogged or cracked.
3. Nozzle is in high pressure mode.
4. Check ball stuck in detergent siphoning system.
1. Insert detergent siphoning tube into detergent.
2. Clean or replace detergent siphoning tube.
3. Push nozzle forward for low pressure mode.
4. Unstick check ball as described in Detergent Siphoning
Check Ball.
Engine runs good at no-load but “bogs” when
load is added.
Engine speed is too slow. Move throttle control to Fast position. If engine still “bogs
down”, contact local service facility.
Engine will not start; shuts down during
operation or starts and runs rough.
1. Low oil level.
2. Dirty air cleaner.
3. Out of fuel.
4. Stale fuel.
5. Spark plug wire not connected to spark plug.
6. Bad spark plug.
7. Water in fuel.
8. Excessively rich fuel mixture.
1. Fill crankcase to proper level.
2. Clean or replace air cleaner.
3. Fill fuel tank.
4. Drain fuel tank; fill with fresh fuel.
5. Connect wire to spark plug.
6. Replace spark plug.
7. Drain fuel tank; fill with fresh fuel.
8. Contact local service facility.
Engine lacks power. Dirty air filter. Replace air filter.
Product Specifications
Outlet Pressure..................................137.9 BARS (2,000 PSI)*
Flow Rate .......................................7.2 liters/min (1.9 GPM)
Water Supply Temperature ...............................38ºC (100ºF) MAX
Displacement ..................................................158 cc
Spark Plug Gap...................................... 0.76 mm (0.030 in.)
Fuel Capacity.........................................0.95 Liters (1.0 Qt.)
Oil Capacity........................................0.6 Liters (20 Ounces)
Common Service Parts
PumpSaver ..................................................... 6039
O-Ring Maintenance Kit .......................................191922GS
Water Inlet Screen ............................................B2384GS
Air Cleaner .............................................698369 or 5088
Resistor Spark Plug ......................................802592 or 5095
Long Life Platinum Spark Plug ...................................... 5062
Engine Oil Bottle ......................................100005 or 1000028
Fuel Stabilizer ........................................1000120 or 100117
Spark Arrester................................................. 398067
Power Ratings: The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power &
Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM;
horsepower values are derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and air cleaner
installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher than net engine power and is affected by, among other
things, ambient operating conditions and engine-to-engine variability. Given the wide array of products on which engines are placed, the gas engine may not develop the rated gross
power when used in a given piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine components (air cleaner,
exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due
to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.
* This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure
Washers).
Not for
Reproduction
15
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC PRESSURE WASHER OWNER WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workmanship or
both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is subject to
the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.com. The
purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one year from purchase,
or to the extent permitted by law. All other implied warranties are excluded. Liability for incidental or consequential damages are excluded to the extent exclusion
is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state or country to country.**
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM, or by
calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated above. “Consumer use”
means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once
equipment has experienced commercial use, it shall thereafter be considered as commercial use for purposes of this warranty.
NOWARRANTYREGISTRATIONISNECESSARYTOOBTAINWARRANTYONBRIGGS&STRATTONPRODUCTS.SAVEYOURPROOFOFPURCHASERECEIPT.IFYOUDONOT
PROVIDEPROOFOFTHEINITIALPURCHASEDATEATTHETIMEWARRANTYSERVICEISREQUESTED,THEMANUFACTURINGDATEOFTHEPRODUCTWILLBEUSEDTO
DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR WARRANTY
We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty repairs are handled
routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if equipment damage occurred because of misuse,
lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the pressure
washer or engine has been removed or the equipment has been altered or modified. During the warranty period, the Authorized Service Dealer, at its option, will repair or replace
anypartthat,uponexamination,isfoundtobedefectiveundernormaluseandservice.Thiswarrantywillnotcoverthefollowingrepairsandequipment:
• NormalWear:OutdoorPowerEquipment,likeallmechanicaldevices,needsperiodicpartsandservicetoperformwell.Thiswarrantydoesnotcoverrepairwhennormaluse
has exhausted the life of a part or the equipment.
• InstallationandMaintenance:Thiswarrantydoesnotapplytoequipmentorpartsthathavebeensubjectedtoimproperorunauthorizedinstallationoralterationand
modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment, to adversely affect its performance
and reliability. This warranty also does not cover normal maintenance such as air filters, adjustments, fuel system cleaning and obstruction (due to chemical, lime, dirt, and
so forth).
• OtherExclusions:Thiswarrantyexcludeswearitemssuchasquickcouplers,seals,o-rings,pumpsthathavebeenrunwithoutwatersuppliedordamageormalfunctions
resulting from accidents, abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration. Accessory parts, such as guns, hoses, nozzle
extensions (wands), and nozzles, are excluded from the product warranty. This warranty excludes used, reconditioned, and demonstration equipment and failures due to
acts of God and other force majeure events beyond the manufacturers control. 198203E, Rev. D, 04/17/2012
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
MILWAUKEE, WI, USA
Effective April 1, 2012; replaces all undated Warranties and all Warranties dated before April 1, 2012.
2 years
90 Days
Consumer Use
Commercial Use
WARRANTY PERIOD
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Merci d’avoir acheté cette laveuse haute pression Briggs & Stratton® de qualité. Nous sommes heureux que vous fassiez confiance à la marque Briggs & Stratton. Si vous respectez
les instructions d’utilisation et d’entretien de ce manuel, vous pourrez vous fier à votre laveuse haute pression Briggs & Stratton durant de nombreuses années.
Ce manuel contient des renseignements sur la sécurité pour vous informer des dangers et des risques associés laveuses à pression ainsi que de la façon de les éviter. Briggs &
Stratton n’a pas nécessairement connaissance de toutes les applications pour lesquelles cette laveuse haute pression peut être utilisée ; il est donc important que vous lisiez et
compreniez ces instructions avant d’essayer de faire démarrer ou d’utiliser cet appareil. Conservez ces instructions originale pour vous y référer ultérieurement.
Cette laveuse haute pression doit être montée avant toute utilisation. Consultez la section Montage de ce manuel pour connaître les étapes du montage final. Suivez ces directives
à la lettre.
Où nous trouver
Vousn’aurezjamaisàchercherbienloinpourtrouveruncentredesupportetserviceBriggs&Strattonpourvotrelaveusehautepression.Plusieursmilliersdedistributeursde
serviceaprès-venteagréésBriggs&Strattondanslemondeoffrentunservicedequalité.Voustrouverezaussileplusprochedistributeurdeserviceagréésurlacartedesdétaillants
BRIGGSandSTRATTON.COM.
Table des matières
Sécurité de l’opérateur......................................5
Description de l’équipement......................................................5
Informations de sécurité importantes...............................................5
Assemblage .............................................7
Déballage de la laveuse haute pression .............................................7
Fixer la poignée ...............................................................7
Installer le kit de roues..........................................................7
Ajouter l’huile moteur...........................................................7
Ajouter du carburant............................................................7
Lubrification des chaînes ........................................................7
Raccorder le flexible et l’alimentation en eau à la pompe.................................8
Caractéristiques et commandes ................................ 8
Fonctionnement...........................................8
Emplacement du laveuse haute pression .............................................8
Démarrage de la laveuse haute pression..............................................8
Procédure d’arrêt du laveuse haute pression .........................................9
Utilisation de la buse réglable ......................................................9
Application de détergent.........................................................9
Rinçage avec le laveuse haute pression ............................................10
Nettoyage du tube de siphonage de détergent .......................................10
Système de refroidissement automatique (dissipation de la chaleur) .....................10
Entretien...............................................10
Calendrier d’entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Entretien du laveuse haute pression...............................................11
Entretien du moteur ...........................................................12
Après chaque utilisation ........................................................13
Entreposage d’hiver ...........................................................13
Entreposage à long terme.......................................................13
Diagnostic des problèmes...................................14
Caractéristiques..........................................14
Caractéristiques du produit .....................................................14
Pièces d’entretien courantes.....................................................14
Garanties ..............................................15
Garantie propriétaire du laveuse haute pression .....................................15
Copyright © 2012. Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, États-Unis d’Amérique. Tous droits réservés.
Briggs & Stratton Power Products est une marque
déposée inscrite de Briggs & Stratton Corporation
Milwaukee, WI, États-Unis d’Amérique
INSTRUCTIONS ORIGINALE
Laveuse haute pression
Référence du modèle
Révision
Numéro de Série
Date d’achat
Moteur
Numéro de modèle
Numéro du type
Numéro du code
Not for
Reproduction
5 5
Sécurité de l’opérateur
Description de l’équipement
L’utilisateur doit lire ce manuel soigneusement et se familiariser avec le
laveuse haute pression. Il doit prendre connaissance de ses applications,
de ses limites et des risques inhérents à son utilisation.
Cette laveuse haute pression fonctionne sous 137,9 bars (2 000 PSI) avec un débit de
7,2 l/minute. Cet appareil domestique de grande qualité comporte des roues de 17,8 cm,
une pompe à came axiale avec pistons en acier inoxydable, un circuit de refroidissement
automatique, un circuit de siphonage de détergent, un embout de pulvérisation réglable,
un tuyau souple à usage industriel de 9,1 m et plus encore.
Tout a été fait pour s’assurer que les renseignements contenus dans le présent guide
soient exacts et à jour. Toutefois, le fabriquant se réserve le droit de changer, de modifier
ou encore d’amélorer le système en tout temps et ce, sans préavis.
Informations de sécurité importantes
Le fabricant ne peut anticiper toute circonstance possible pouvant présenter un risque. Les
avertissements contenus dans ce manuel et les étiquettes et autocollants apposés sur l’ap-
pareil ne sont ainsi pas exhaustifs. Si vous utilisez une procédure, une méthode de travail
ou une technique de fonctionnement non spécifiquement recommandée par le fabricant,
ilvousrevientdevousassurerquecelle-ciestsûrepourvousetpourautrui.Vousdevez
également vous assurer que la procédure, méthode de travail ou technique de fonctionne-
ment que vous avez choisie ne nuit pas à la sécurité du laveuse haute pression.
Symboles de sécurité et leur signification
Le symbole d’alerte de sécurité signale un risque potentiel de blessure
corporelle.Untermedesignalement(DANGER,AVERTISSEMENTouMISEEN
GARDE) accompagne le symbole d’alerte pour désigner un degré ou niveau de gravité
du risque. Un symbole de sécurité peut être présent pour représenter le type de
risque. Le mot de signalement AVIS désigne des pratiques sans rapport avec des
blessures corporelles.
Le mot DANGER indique un danger qui, s’il n’est pas évité, causera la mort ou
des blessures graves.
Le mot AVERTISSEMENT indique un risque qui, s’il n’est pas évité, pourrait
causer la mort ou des blessures graves.
Le terme MISE EN GARDE indique un risque qui, s’il n’est pas évité, pourrait
causer des blessures mineures ou modérées.
Le mot AVIS concerne des pratiques sans rapport avec d’éventuelles blessures
corporelles.
Plaque d’avertissement
Figure
1
Une plaque d’avertissement figure sur l’appareil pour signaler les risques pour la
sécurité. Si cette plaque vient à être endommagée ou illisible, la remplacer par une
étiquette neuve disponible auprès de votre représentant local Briggs & Stratton.
Les pictogrammes de la plaque d’avertissement sont explicités plus bas dans cette
section consacrée à la sécurité.
AVERTISSEMENT Les moteurs émettent du monoxyde de carbone, un gaz
toxique sans odeur ni couleur.
L’inhalation du monoxyde de carbone peut entraîner la mort, de graves
lésions, des maux de tête, de la fatigue, des vertiges, des vomissements, de
la confusion, des crises d’épilepsie, des nausées ou des évanouissements.
Certains produits chimiques ou détergents pourrait être nocifs en cas d’inhalation
ou d’ingestion, et entraîner la mort, de graves lésions, des nausées, des
évanouissements ou un empoisonnement.
• UtiliserceproduitUNIQUEMENTàl’extérieur.
• Empêchezlesgazd’échappementdepénérerdansunlieuconfinéparlesfenêtres,
portes, entrées d’aération et d’autres ouvertures.
• NEPASutiliserceproduitàl’intérieurd’unbâtiment,d’unabri-garage,d’un
porche, de matériel roulant, de matériel maritime, ou d’un espace clos, même si
les portes et les fenêtres sont ouvertes.
• Utiliserunrespirateurouunmasqueencasderisqued’inhalationlorsde
l’utilisation de produits chimiques.
• Liretouteslesinstructionsquiaccompagnentlemasquepours’assurerquecelui-
ci fournira la protection nécessaire contre l’inhalation des vapeurs nocives lors de
l’utilisation de produits chimiques.
AVERTISSEMENT Lereculducâblededémarreur(rétractationrapide)apour
effet de tirer la main et le bras en direction du moteur plus rapidement qu’il
n’estpossibledelelâcher,cequipourraitprovoquerdesfêlures,fractures
osseuses, des contusions ou des entorses entraînant de graves lésions.
• NEJAMAIStirersurlecordondudémarreursanslibérerd’abordlapressiondu
pistolet de pulvérisation.
• Lorsdudémarragedumoteur,tirerlentementsurlacordejusqu’àsentirune
résistance, puis tirer rapidement afin d’éviter l’effet de recul.
• Aprèschaquetentativededémarragequiéchoue,toujourspointerlepistoletde
pulvérisation dans une direction sans danger, appuyer sur le bouton rouge et
enfoncerlagâchettedupistoletdepulvérisationpourlibérerlapression.
• Pourévitertoutrisquedeblessureencasdereculdupistoletdepulvérisation,le
tenir fermement des deux mains pour la pulvérisation haute pression.
AVERTISSEMENT
Risque de brûlure chimique.
Les produits chimiques pourraient provoquer des brûlures entraînant la
mort, de graves lésions, et/ou endommager les biens.
• NeJAMAISutiliserdeliquidecaustiqueaveclenettoyeuràhautepression.
• UtilisezSEULEMENTdesdétergents/savonssansrisquededommagespourle
nettoyeuràhautepression.Veuillezsuivretouteslesdirectivesdesfabricants.
AVERTISSEMENT Risque d’électrocution.
Le contact avec la source d’alimentation électrique pourrait provoquer un
choc électrique ou une brûlure entraînant la mort ou de graves lésions.
• NEJAMAISpulvériserprèsd’unesourced’alimentationélectrique.
Incendie
Explosion
Vapeurstoxiques
Surface chaude
Pièces en
mouvement
Choc électrique
Risque de recul
Projection d’objets
Manuel d’opérateur
Injection de fluide Brûlure chimique
Projectile
Surface glissanteRisque de chute
AVERTISSEMENT
La chaleur/les gaz d’échappement pourrait enflammer les
produits combustibles, les structures ou endommager le
réservoir d’essence en provoquant un feu, et entraîner la
mort, de graves lésions et/ou endommager les biens.
Le contact avec la zone du pot d’échappement pourrait provoquer des brûlures
entraînant de graves lésions.
• NEPAStoucherauxpièceschaudesetÉVITERlecontactaveclesgazd’échappement.
• Laisserl’équipementrefroidiravantd’ytoucher.
• Conserverundébattementd’aumoins1.5mautourdulaveusehautepression,y
compris au-dessus du nettoyeur.
• Contacterlefabriquant,détaillantourevendeurd’originedel’équipementpourobtenir
un pare-étincelles conçu pour le système d’échappement installé sur ce moteur.
• Lespiècesderechangedoiventêtred’origineetinstalléesdanslamêmeposition
que les pièces précédentes.
AVERTISSEMENT
L’utilisation de la laveuse à pression pourrait créer des
mares et des surfaces glissantes ce qui pourrait vous faire
tomber et entraîner la mort ou de graves lésions.
Le recul du pistolet de pulvérisation pourrait vous faire
tomber et entraîner la mort ou de graves lésions.
• Utilisercetappareilsurunesurfacestable.
• Lapenteetledrainagedel’airedenettoyagedoiventêtresuffisantspourréduire
le risque de chute accru sur des surfaces glissantes.
• Agiravecuneextrêmeprudenceencasd’utilisationdulaveusehautepressionsur
une échelle, un échafaudage ou tout autre emplacement relativement instable.
• Pourévitertoutrisquedeblessureencasdereculdupistoletdepulvérisation,le
tenir fermement des deux mains pour la pulvérisation haute pression.
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
AVIS Le jet à haute pression risque d’endommager les articles fragiles, notamment
le verre.
• NEPASpointerdepistoletdenettoyagesurduverreenmodedejetbrisé.
• N’visezjamaisdesplantesaveclepistoletpulvérisateur.
AVIS Le traitement inadéquat du nettoyeur à haute pression peut l’endommager et
réduire sa durée de vie utile
.
• Sivousavezdesquestionsàproposdel’utilisationprévuedecetappareil,consultez
votre détaillant.
• N’utilisezJAMAISunappareilayantdespiècesbriséesoumanquantesousansbâti
ou couvercles protecteurs.
• NEneutralisezAUCUNdispositifdesécuritédecettemachine.
• NEmodifiezPASlavitesseréguléedumoteur.
• N’utilisezPASlenettoyeuràpressionàdesvaleursexcédantlapressionnominale.
• NEmodifiezPASlenettoyeuràpression.
• Partempsfroid,avantdedémarrerlenettoyeuràpression,vérifiez-entousles
éléments pour vous assurer qu’aucune glace ne s’y est formée.
• N’utilisezJAMAISletuyauàhautepressioncommepoignéepourdéplacerl’appareil.
Utilisez toujours la poignée de l’appareil.
• CetappareilestconçupourêtreutiliséuniquementavecdespiècesBriggs&Stratton
approuvées. Si l’appareil est utilisé avec des pièces qui NE sont PAS conformes
aux caractéristiques minimales, tous les risques et responsabilités incomberont à
l’utilisateur.
AVERTISSEMENT
Le carburant et ses vapeurs sont extrêmement
inflammables et explosifs ce qui peut provoquer des brûlures,
un feu ou une explosion entraînant la mort, de graves lésions
et/ou endommager les biens.
LORS DE L’AJOUT OU DE LA VIDANGE DE CARBURANT
• ARRÊTERlemoteurdelalaveuseàpressionetlelaisserrefroidiraumoins2
minutes avant d’ouvrir le bouchon du réservoir de carburant. Desserrer lentement
de bouchon pour libérer la pression présente à l’intérieur du réservoir.
• Remplirouvidangerleréservoirdecarburantàl’extérieur.
• NEPAStropremplirleréservoir.Laisserunespacesuffisantpourl’évaporationde
l’essence.
• Encasderenversementdecarburant,attendrequ’ils’évaporeavantdelancerle
moteur.
• Manipulerl’essenceàl’abridesétincelles,desflammesnues,desveilleuses,dela
chaleur ainsi que d’autres sources potentielles d’inflammation.
• Contrôlerquelesdurits,leréservoir,lebouchonetlesraccordsdecarburantne
présentent ni fissures ni fuites. Remplacer si nécessaire.
• NEPASallumerdecigarettes,nifumer.
LORS DE LA MISE EN MARCHE DE L’APPAREIL
• Vérifierquelabougie,lesilencieux,lebouchondecarburantetlefiltreàairsont
en place.
• NEPAStenterdefairedémarrerlemoteurenl’absencedebougie.
UTILISATION DE L’ÉQUIPEMENT
• NEPASfairefonctionnerceproduitàl’intérieurd’unbâtiment,d’unabri-garage,
d’un porche, d’un matériel roulant, de matériel maritime ou d’un espace clos.
• NEJAMAISinclinerlemoteurnil’équipementaupointquel’essencesemetteà
couler.
• NEPASvaporiserdeliquidesinflammables.
LORS DU TRANSPORT, DU DÉPLACEMENT OU DE LA RÉPARATION DE L’ÉQUIPEMENT
• Leréservoird’essencedoitêtreVIDEoulerobinetd’arrêtd’essencedoitêtreen
position fermée (OFF) pendant le transport, le déplacement ou la réparation.
• NEJAMAISinclinerlemoteurnil’équipementaupointquel’essencesemetteà
couler.
• Débrancherlefildelabougie.
ENTREPOSAGE D’ESSENCE OU D’UN ÉQUIPEMENT DONT LE RÉSERVOIR
CONTIENT DE L’ESSENCE
• NEPASentreposeràproximitédefours,poêles,chauffe-eau,sèche-lingeou
d’autres équipements susceptibles de comporter une veilleuse ou une source
potentielle d’inflammation des vapeurs d’essence.
AVERTISSEMENT
Une production involontaire d’étincelles peuvent
provoquer un feu ou un choc électrique entraînant la mort ou
de graves lésions.
POUR RÉGLER OU RÉPARER LE LAVEUSE HAUTE PRESSION
• Débrancherlefildebougied’allumageetl’écarterdesortequ’ilnepuissetoucher
la bougie.
LORS DES ESSAIS D’ALLUMAGE
• Utiliseruntesteurdebougied’allumageapprouvé.
• NEPASvérifierl’allumagelorsquelabougieestretirée.
AVERTISSEMENT
Le démarreur ou d’autres pièces rotatives pourraient
happer les mains, les cheveux, les vêtements ou des accessoires et
entraîner de graves lésions.
• NeJAMAISutiliserunappareildontdespiècessontcassées,manquantesounon
munies de leur capot ou de leurs couvercles protecteurs.
• NEPASporterdevêtementsamples,debijouxnid’autreseffetsquipourraient
être happés par le démarreur ou les autres pièces en rotation.
• Retenirlescheveuxlongsenchignonetretirerlesbijoux.
MISE EN GARDE
Des vitesses de fonctionnement excessivement élevées
peuvent entraîner des blessures mineures et/ou des dommages sur les laveuses à
pression.
Des vitesses excessivement faibles imposent une charge lourde.
• NEPASmodifierleressortdurégulateur,lestringlesetautrespiècespour
augmenter le régime du moteur. La laveuse à pression fournit une pression et un
débit nominaux corrects lors d’un fonctionnement à une vitesse régulée.
• NEPASmodifierlalaveuseàpressiondequelquefaçonquecesoit.
AVERTISSEMENT Le jet d’eau sous haute pression produit par cet appareil
pourrait entamer la peau et ses tissus sous-jacents, entraînant de graves
lésions et pouvant conduire à une amputation.
Le pistolet de pulvérisation emprisonne l’eau sous haute pression même
lorsque le moteur est arrêté et l’arrivée d’eau débranchée, ce qui peut
provoquer de graves lésions.
• Encasdecoupureparunliquide,appelerimmédiatementunmédecin.NEPAS
traiter comme une simple coupure.
• NEPASlaisserdesENFANTSmanipulerlelaveusehautepression.
• NEJAMAIStenterderéparerleflexiblehautepression.Leremplacer
systématiquement.
• NeJAMAISréparerlesconnexionsquifuientavecunmasticd’étanchéité.
Remplacer le joint torique ou le joint.
• NEJAMAISbrancherletuyausouplesouspressiondirectementsurl’extension
d’embout de pulvérisation.
• Toujoursgarderletuyauflexiblehautepressionraccordéàlapompeetaupistolet
de pulvérisation lorsque le système est sous pression.
• Lorsdechaquearrêtdumoteur,TOUJOURSdirigerl’emboutdepulvérisationvers
unedirectionsansdanger,appuyersurleboutonrougeetenfoncerlagâchettedu
pistolet de pulvérisation pour libérer la pression.
• NEJAMAISdirigerlejetversdespersonnes,desanimauxoudesplantes.
• NEPASverrouillerlepistoletdepulvérisationenpositionouverte.
• NEPASlaisserlepistoletdepulvérisationsanssurveillancelorsquel’appareilest
en marche.
• NeJAMAISutiliserunpistoletdepulvérisationdontleverroudedétenteoule
pontet n’est pas installé et en ordre de marche.
• Toujourss’assurerquelepistoletdepulvérisation,lesbusesetlesaccessoires
sont bien fixés.
AVERTISSEMENT
Risque de lésion oculaire ou corporelle.
Le jet d’eau peut rejaillir ou propulser des objets en entraînant
de graves lésions.
• Toujoursporterdeslunettesdeprotectionàventilationindirecte(projectionde
produit chimique) conformes à la norme ANSI Z87.1 lors de l’utilisation, ou à
proximité, de ce matériel.
• NeJAMAISremplacerleslunettesdeprotectionàventilationindirectepardes
lunettes de sécurité ou des lunettes de protection pour environnement sec.
• Toujoursporterdesvêtementsprotecteurstelsqu’unechemiseàmanches
longues, des pantalons longs et des chaussures à bout fermé.
• NEJAMAISutiliserlalaveuseàpressionnu-pieds,ensandalesouenshort.
Not for
Reproduction
7 7
Assemblage
Lire entièrement le manuel d’opérateur avant de monter et d’utiliser
l’appareil.
La laveuse haute pression doit être montée ; elle est prête à être utilisée après avoir été
convenablement remplie avec l’huile et le carburant conseillés.
En cas de problème de montage de la laveuse haute pression, s’adresser au distributeur
de service après-vente agréé Briggs & Stratton local. Pour obtenir de l’aide, se munir
des numéros de modèle, de révision et de série inscrits sur l’étiquette d’identification.
Reportez-vous au chapitre Caractéristiques et commandes pour repérer l’emplacement
de l’étiquette d’identification.
Déballage de la laveuse haute pression
1. Sortir le sac de pièces, les accessoires et les inserts inclus avec la laveuse
haute pression.
2. Ouvrir complètement le carton en coupant chaque angle de haut en bas.
3. Vérifierquetouslesélémentssontinclusavantdecommencerlemontage.
La boîte contient les éléments suivants :
• Unitéprincipale
• Poignée
• Flexiblehautepression
• Pistoletdepulvérisation
• Rallongedebuseréglable
• Roues(2)
• Sachetdepiècesdétachées(contenantlesélémentssuivants):
• Manueld’opérateur
• Kitd’entretien
• Raccordsdetuyau
• Sacderangementdesaccessoires
• Poignée/RouesKitdematérieldefixation:
• Boulon(2)
• Boutonsenplastique(2)
• Axed’essieu(2)
• Goupillesdefixation(2)
Pour mettre le laveuse haute pression en état de fonctionnement, les tâches
suivantes doivent être effectuées:
1. Fixer la poignée et les roues au boîtier principal.
2. Faire le niveau d’huile.
3. Faire le plein d’essence.
4. Raccorder le flexible haute pression au pistolet et pompe.
5. Raccorder l’alimentation en eau à la pompe.
6. Monter la rallonge de buse réglable sur le pistolet.
Fixer la poignée Figure
2
1. Placer la poignée (A) sur la base (B).Vérifierquelestrousdelapoignéesont
alignés sur ceux de la base.
2. Insérer les boulons de carrosserie (C) dans les trous à l’extérieur de l’appareil
et fixer un bouton de plastique (D) à partir de l’intérieur de l’appareil. Serrer à la
main.
Installer le kit de roues Figure
3
Le kit de roues est destiné à améliorer la facilité de transport de la laveuse haute pression.
AVIS Le kit de roues n’est pas destiné à une utilisation sur route.
Installer le kit de roues de la manière suivante :
1. Placer la partie inférieure de la laveuse haute pression sur une surface plane et
régulière.
2. Faire glisser une roue (A) par-dessus l’axe d’essieu (B).
AVISVeilleràinstallerlaroueaveclemoyeuenreliefversl’intérieur.
3. Faire glisser l’axe d’essieu par le trou (C) du cadre.
4. Fixer la roue sur l’axe d’essieu avec la goupille de fixation (D).
5. Répéter les étapes 2 à 4 pour fixer la seconde roue.
Ajouter l’huile moteur
1. Placer la laveuse haute pression sur une surface plane de niveau.
2. Ajoutez de l’huile moteur comme indiqué dans le chapitre Appoint en huile
moteur de la section Maintenance du moteur.
AVIS Une manipulation inappropriée de la laveuse haute pression peut
l’endommager et raccourcir sa durée de vie utile.
• NEPASessayerdefairedémarrerlemoteuravantdel’avoirconvenablementrempli
avec l’huile conseillée. Ceci peut provoquer un dysfonctionnement du moteur.
Ajouter du carburant Figure
4
Le carburant doit satisfaire aux spécifications suivantes :
• Essencepropre,neuve,sansplomb.
• Indiced’octaneminimumde87/87AKI(NOR91).Utilisationenhautealtitude,
voir Haute altitude.
• Ilestpossibled’utiliserdel’essenceavecadditionde10%maximumd’éthanol
(mélangeessence-alcool)oude15%maximumd’étherméthyl-tertiobutylique
(MTBE).
AVIS Éviter d’endommager la laveuse haute pression.
Le non-respect des instructions du manuel d’utilisation relatives au carburant
annulera la garantie.
• NEPASutiliserd’essencenonapprouvée,tellequedubioéthanol(E85).
• NEPASmélangerd’huileavecl’essence.
• NEPASmodifierlemoteurpourlefairefonctionneravecdescarburantsalternatifs.
Pour protéger le circuit de carburant contre la formation de gomme, mélanger l’essence
àunstabilisateurdecarburantlorsduremplissage.VoirEntreposage. Tous les
carburants ne sont pas identiques. En cas de problèmes de démarrage ou de mauvaises
performances après l’utilisation d’un carburant, choisir un autre fournisseur ou changer
demarque.Cemoteurestcertifiépourfonctionneràl’essence.Lesystèmedecontrôle
des émissions dans l’environnement de ce moteur est du type EM (Engine Modifications).
1. Nettoyer la zone entourant le bouchon de remplissage d’essence, retirer le
bouchon.
2. Ajouter lentement du carburant sans plomb normal (A) dans le réservoir
de carburant (B).Veillerànepastropleremplir.Laisserenviron4cm(C)
d’espace vide dans le réservoir pour l’expansion du carburant.
3. Installer le bouchon de carburant et laisser toute trace de carburant s’évaporer
avant de faire démarrer le moteur.
Haute altitude
À une altitude supérieure à 1524 mètres, il est possible d’utiliser de l’essence avec un
indice d’octane de 85 / 85 AKI (NOR de 89). Pour rester conforme aux réglementations
sur les émissions dans l’environnement, un réglage est nécessaire pour la haute altitude.
Tout fonctionnement sans que ce réglage soit effectué provoquera une baisse des
performances, une augmentation de la consommation de carburant et une augmentation
des émissions dans l’environnement. Consulter un concessionnaire Briggs & Stratton
agréée pour toute information sur le réglage pour la haute altitude. Il n’est pas conseillé
d’utiliser l’appareil à une altitude inférieure à 762 mètres avec le kit de haute altitude.
Lubrification des chaînes Figure
5
La lubrification des joints toriques est extrêmement importante pour l’installation et le
fonctionnement. L’utilisation d’un produit lubrifiant (vaseline ou graisse synthétique)
pendant le montage aide les joints toriques à s’emboîter correctement et fournit une
meilleure étanchéité. Elle permet aussi de protéger les joints toriques contre les dommages
provoqués par l’abrasion, le pincement ou la coupure et prolonge leur durée de vie.
AVIS TOUJOURS appliquer une petite quantité de produit lubrifiant sur les joints
toriques avant de monter le tuyau d’arrosage sur la pompe (A), extrémité filetée du
tuyau haute pression (B), le pistolet de pulvérisation (C) extrémité du tuyau haute
pression à raccord rapide (D).
Lubrifier tous les raccords indiqués ci-dessous en suivants ces instructions :
1. Inspecter et nettoyer les surfaces des raccords avant la lubrification et le montage.
2. Utiliser les produits lubrifiants avec parcimonie pendant le montage ; un film fin
suffit.
3. Utiliser un petit pinceau plat ou un chiffon de coton pour appliquer la
graisse directement sur les joints toriques lorsqu’ils ne sont pas directement
accessibles (raccord QC, raccord M22).
AVERTISSEMENT
Le carburant et ses vapeurs sont extrêmement
inflammables et explosifs, ce qui peut provoquer des brûlures,
un incendie ou une explosion susceptibles d’entraîner la mort,
de graves blessures et/ou des dommages matériels.
LORS DE L’AJOUT DE CARBURANT
• Arrêterlalaveusehautepression(OFF)etlalaisserrefroidirpendantaumoins
2 minutes avant de retirer le bouchon de carburant. Desserrer lentement de
bouchon pour libérer la pression du réservoir.
• Remplirleréservoirdecarburantàl’extérieur.
• NEPAStropremplirleréservoir.Laisserunespacesuffisantpourl’évaporationde
l’essence.
• Encasderenversementdecarburant,attendrequ’ils’évaporeavantdelancerle
moteur.
• Manipulerl’essenceàl’abridesétincelles,desflammesnues,desveilleuses,dela
chaleur ainsi que d’autres sources potentielles d’inflammation.
• Contrôlerquelesdurits,leréservoir,lebouchonetlesraccordsdecarburantne
présentent ni fissures ni fuites. Remplacer si nécessaire.
• NEPASallumerdecigarettes,nifumer.
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
Raccorder le flexible et l’alimentation en eau
à la pompe Figure
6
7
8
9
AVIS NE PAS faire fonctionner la pompe sans avoir branché et ouvert l’arrivée d’eau.
• Lagarantieseraannuléesidesdommagesàl’appareilsontentraînésparlenon-
respect de cette directive.
AVIS Retirer et jeter les bouchons de transport de la sortie haute pression de la
pompe et de l’admission d’eau avant de brancher les tuyaux.
1. Dérouler le flexible haute pression et fixer une extrémité à la base du pistolet
(6). Repousser le collier du raccord rapide, emboîter le raccord sur la pistolet et
relâcherlecollier.Tirersurletuyaupourvérifierlasoliditédubranchement.
2. Fixer l’autre extrémité du flexible haute pression à la sortie haute pression de la
pompe (7). Serrer à la main.
3. Faire couler l’eau dans le tuyau d’arrosage pendant trente secondes pour
éliminer tous les débris en suspension. Refermer l’eau.
AVIS NE PAS siphonner une eau stagnante pour alimenter le nettoyeur. Utiliser
EXCLUSIVEMENTdel’eaufroide(moinsde38°C).
4. Avant de raccorder le tuyau d’arrosage à l’entrée d’eau du nettoyeur, inspecter
le tamis d’entrée (8,A). Nettoyer le tamis s’il contient des débris, le remplacer
s’il est endommagé. NE JAMAIS UTILISER UN laveuse haute pression DONT LE
TAMIS D’ENTRÉE EST ENDOMMAGÉ.
AVIS Le connecteur d’admission d’eau ou la pompe peut être endommagé si une
valve de retenue (reniflard ou clapet anti-retour) est branchée à la pompe.
• IlDOITyavoiraumoins3mdetuyaud’arrosagesansrestrictionentrel’admission
de la laveuse haute pression et tout dispositif tel qu’une valve de retenue.
• Toutdommageaumatérielprovoquéparl’installationd’unevalvederetenueàla
pompe annulera la garantie.
5. Brancher le tuyau d’arrosage (de 15 m de long au maximum) à l’admission
d’eau (8). Serrer à la main.
6. Ouvrir l’eau, appuyer sur le bouton rouge (9,A) du pistolet et enfoncer la
détente pour purger le système de pompe de l’air et des impuretés.
Liste de vérifications avant le démarrage du moteur
Inspecterlemontagedel’appareilpourconfirmerquelestâchessuivantesontétéaccomplies:
1. Lire la section Sécurité de l’opérateur et la section Fonctionnement avant
d’utiliser la laveuse haute pression.
2. Vérifierquelapoignéeestenplaceetbienfixée.
3. Vérifierqueleniveaud’huileducartermoteurestcorrect.
4. Vérifierquel’essenceajoutéedansleréservoirestd’untypeapproprié.
5. Vérifierquelestuyauxsouplessontsolidementbranchés.
6. Vérifierl’absencedepliure,coupureouavariesurletuyauhautepression.
7. Vérifierquel’alimentationeneauetsondébitsontappropriés.
Caractéristiques et commandes Figure
10
Lisez ce manuel d’opérateur et ces règles de sécurité avant d’utiliser le
laveuse haute pression. Reportez-vous aux illustrations pour repérer
l’emplacement des divers réglages et commandes de votre nettoyeur.
Conservez ce manuel pour pouvoir vous y référer ultérieurement.
A - Lanceur - Sert à démarrer le moteur manuellement.
B - Remplissage/Jauge d’huile—Vérifier,rempliretvidangerl’huile.
C - Pompe - Fournit la haute pression.
D - Système de refroidissement automatique - Fait circuler de l’eau dans la pompe
lorsque la température de l’eau atteint 51 à 68 ºC. L’eau chaude de la pompe est
évacuée au sol. Ce système prévient tout dommage interne à la pompe.
E - Flexible haute pression - Raccorder une des extrémités du flexible à la pompe à
eau et l’autre au pistolet de pulvérisation.
F - Pistolet de pulvérisation-Undispositifdedétentepermetdecontrôlerlejetd’eau
sur la surface à nettoyer. Inclut un verrou de déclenchement.
G - Buse réglable - Toujours fixée à la rallonge de buse. La buse réglable permet de
régler la pression et la forme du jet.
H - Réservoir d’essence — Remplir le réservoir d’essence sans plomb normale.
Toujours laisser de la place pour l’expansion du carburant.
Éléments non représentés :
Filtre à air - Protège le moteur en filtrant la poussière et les débris avant la prise d’air.
Étiquette d’identification (près de l’arrière de la semelle) — Indique le numéro de
modèle et de série de la laveuse haute pression. Garder ces renseignements à portée
de main en cas d’appel pour demander de l’aide.
Tube de siphonage de détergent — Utiliser pour siphonner le détergent sans danger
de la laveuse haute pression vers le circuit à basse pression.
Sortie haute pression - Sert au branchement du flexible haute pression.
Bulle d’amorçage — Prépare le moteur froid au démarrage.
Levier de régulateur - Cette manette place le moteur en mode démarrage pour le
lanceur et arrête le moteur lorsqu’il est en marche.
Admission d’eau - Raccorder le tuyau d’arrosage à cet endroit.
Fonctionnement
Emplacement du laveuse haute pression Figure
11
Débattement et circulation d’air
Placer la laveuse haute pression à l’extérieur dans un lieu où les gaz d’échappement mor-
tels ne pourront pas s’accumuler. NE PAS placer la laveuse haute pression là où les gaz
d’échappementmortelspourraients’accumuleretpénétrerouêtreentraînésdansunbâtiment
susceptible d’être occupé. Assurez-vous que les gaz d’échappement (A) ne puissent entrer par
une fenêtre, une porte, une prise d’aération ou une autre ouverture qui pourrait leur permettre
de s’accumuler dans un espace clos. Il faut tenir compte des vents dominants et des courants
d’air lors de la mise en place de la laveuse haute pression.
Démarrage de la laveuse haute pression Figure
12
13
14
Pour le démarrage initial du laveuse haute pression, suivre les instructions pas à pas.
Ces instructions de démarrage sont également valables si le nettoyeur n’a pas été
utilisépendantplusd’unejournée.:
1. Placer le laveuse haute pression près d’une arrivée d’eau extérieure capable
d’un débit supérieur à 11,0 litres/minute sous une pression égale ou supérieure
à20PSI(1,38bar)auniveaudel’extrémitédutuyaud’arrosage,côtélaveuse
haute pression. NE PAS siphonner l’eau d’alimentation.
2. Vérifierqueleflexiblehautepressionestsolidementraccordéaupistoletetàla
pompe.VoirlasectionAssemblage.
3. S’assurer que l’appareil est placé sur une surface plane.
4. Vérifierqueletuyaud’arrosageestraccordéàl’entréed’eaudelapompedu
laveuse haute pression.
AVIS NE PAS faire fonctionner la pompe si l’alimentation en eau n’est pas raccordée
et ouverte.
• Lagarantieseraannuléesil’équipementestendommagéparsuitedunon-respectde
cette instruction.
AVERTISSEMENT Le jet d’eau sous haute pression produit par cet appareil
pourrait entamer la peau et ses tissus sous-jacents, entraînant de graves
lésions et pouvant conduire à une amputation.
• NEJAMAISbrancherletuyausouplesouspressiondirectementsurl’extension
d’embout de pulvérisation.
• Toujoursgarderletuyauflexiblehautepressionraccordéàlapompeetaupistolet
de pulvérisation lorsque le système est sous pression.
• Toujourss’assurerquelepistoletdepulvérisation,lesbusesetlesaccessoires
sont bien fixés.
AVERTISSEMENT
Risque de lésion oculaire ou corporelle.
Le jet d’eau peut rejaillir ou propulser des objets en entraînant de
graves lésions.
• Toujoursporterdeslunettesdeprotectionàventilationindirecte(projectionde
produit chimique) conformes à la norme ANSI Z87.1 lors de l’utilisation, ou à
proximité, de ce matériel.
• NeJAMAISremplacerleslunettesdeprotectionàventilationindirectepardes
lunettes de sécurité ou des lunettes de protection pour environnement sec.
AVERTISSEMENT
Les moteurs émettent du monoxyde de carbone, un gaz
toxique sans odeur ni couleur.
L’inhalation du monoxyde de carbone peut entraîner la mort, de graves
lésions, des maux de tête, de la fatigue, des vertiges, des vomissements, de
la confusion, des crises d’épilepsie, des nausées ou des évanouissements.
• UtiliserceproduitUNIQUEMENTàl’extérieur.
• Empêchezlesgazd’échappementdepénérerdansunlieuconfinéparlesfenêtres,
portes, entrées d’aération et d’autres ouvertures.
• NEPASutiliserceproduitàl’intérieurd’unbâtiment,d’unabri-garage,d’un
porche, de matériel roulant, de matériel maritime, ou d’un espace clos, même si
les portes et les fenêtres sont ouvertes.
AVERTISSEMENT
La chaleur/les gaz d’échappement pourrait enflammer les
produits combustibles, les structures ou endommager le réservoir
d’essence en provoquant un feu, et entraîner la mort, de graves lésions
et/ou endommager les biens.
• Conserverundébattementd’aumoins1.5mautourdulaveusehautepression,y
compris au-dessus du nettoyeur.
Not for
Reproduction
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Simplicity 020377-00 Manuel utilisateur

Simplicity
Marque
Simplicity
Modèle
020377-00
Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents