Ariston A6TMH2AF (X) EX Mode d'emploi

English

GB

Operating Instructions

COOKER AND OVEN

Contents

Operating Instructions,1

WARNING,2

Description of the appliance-Overall view,6

Description of the appliance-Control Panel,7

Installation,8

Start-up and use,12

Cooking modes,13

Using the hob,12

Precautions and tips,16

Care and maintenance,17

Assistance,17

FR

Français

Mode d’emploi

CUISINIERE ET FOUR

Sommaire

Mode d’emploi,1

ATTENTION,3

Description de l’appareil-Vue d’ensemble, 6

Description de l’appareil-Tableau de bord, 7

Installation,19

Mise en marche et utilisation,24

Utilisation du plan de cuisson,24

Précautions et conseils, 28

Nettoyage et entretien,29

Assistance,29

PT

Português

Instruções para a utilização

FOGÃO E FORNO

Índice

Instruções para a utilização,1

ATTENTACAO,4

Descrição do aparelho-Vista de conjunto,6

Descriçao do aparelho-Painel de comandos,7

Instalaçao,31

Início e utilizaçao, 36

Utilizaçao do plano de cozedura,36

Utilizaçao do forno,37

Precauçoes e conselhos,40

Manutençao e cuidados,41

Assistencia técnica,41

EnglishEnglish

A6TMH2AF EX

Español

ES

Manual de instrucciones

COCINA Y HORNO

Sumario

Manual de instrucciones,1

Descripción del aparato-Vista de conjunto,6

Descripción del aparato-Panel de control,7

Instalación,43

Puesta en funcionamiento y uso,48

Precauciones y consejos,52

Mantenimiento y cuidados,53

Asistencia,53

ATTENTION,5

Programmes du four,25

AR

A6TMH2AF EXA6TMH2AF EX

2

WARNING: The appliance and its

accessible parts become hot during

use.

Care should be taken to avoid

touching heating elements.

Children less than 8 years of

age shall be kept away unless

continuously supervised.

This appliance can be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe

way and understand the hazards

involved. Children shall not play with

the appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

WARNING: Unattended cooking on a

hob with fat or oil can be dangerous

and may result in fire.

NEVER try to extinguish a fire with

water, but switch off the appliance

and then cover flame e.g. with a lid

or a fire blanket.

Do not use harsh abrasive cleaners

or sharp metal scrapers to clean

the oven door glass since they can

scratch the surface, which may result

in shattering of the glass.

The internal surfaces of the

compartment (where present) may

become hot.

Never use steam cleaners or

pressure cleaners on the appliance.

Remove any liquid from

the lid before opening it.

Do not close the glass cover (if

present) when the gas burners or

electric hotplates are still hot.

WARNING: Ensure that the appliance

is switched off before replacing

the lamp to avoid the possibility of

electric shock.

CAUTION: the use of inappropriate

hob guards can cause accidents.

GB

WARNING

! When you place the rack inside,

make sure that the stop is directed

upwards and in the back of the cavity.

3

FR

ATTENTION: cet appareil ainsi que

ses parties accessibles deviennent

très chauds pendant leur fonctionne-

ment.

Il faut faire attention de ne pas tou-

cher les éléments chauffants.

Ne laisser s’approcher les enfants

de moins de 8 ans à moins qu’ils ne

soient sous surveillance constante.

Le présent appareil peut être utilisé

par des enfants de plus de 8 ans et

par des personnes présentant des

capacités physiques, sensorielles

ou mentales réduites ou n’ayant pas

l’expérience ou les connaissances

nécessaires, à condition qu’ils soient

sous bonne surveillance ou qu’ils

aient reçu les instructions nécessai-

res pour une utilisation de l’appareil

en toute sécurité et à condition qu’ils

se rendent compte des dangers

encourus. Les enfants ne doivent

pas jouer avec l’appareil. Les opéra-

tions de nettoyage et d’entretien ne

doivent pas être effectuées par des

enfants non surveillés.

ATTENTION: laisser un récipient de

cuisson contenant de l’huile ou de la

graisse sur le foyer est dangereux et

risque d’entraîner un incendie.

Il ne faut JAMAIS essayer d’éteindre

une flamme ou un incendie avec de

l’eau! Il faut éteindre l’appareil et

couvrir la flamme avec un couvercle,

par exemple, ou avec une couverture

anti-feu.

Ne pas utiliser de produits abrasifs

ni de spatules métalliques coupan-

tes pour nettoyer la porte du four en

verre, sous peine d’érafler la surface

et de briser le verre.

Les surfaces intérieures du tiroir (s’il

y en a un) peuvent devenir chaudes.

Ne jamais nettoyer l’appareil avec

des nettoyeurs vapeur ou haute pres-

sion.

Essuyer tout liquide pouvant se

trouver sur le couvercle avant de

l’ouvrir. Ne pas abaisser le couvercle

en verre (s’il y en a un) tant que les

brûleurs gaz ou la plaque électrique

sont chauds.

ATTENTION: s’assurer que l’appareil

est éteint avant de procéder au rem-

placement de l’ampoule, afin d’éviter

tout risque d’électrocution.

ATTENTION: l’utilisation de protec-

tions de table inappropriées peut

causer des incendies.

ATTENTION

Lors de l’introduction de la grille,

s’assurer que l’arrêt est bien tourné

vers le haut et se trouve dans la par-

tie arrière de l’enceinte.

Lors de l’introduction de la grille,

s’assurer que l’arrêt est bien tourné

vers le haut et se trouve dans la par-

tie arrière de l’enceinte.

4

PT

ATENÇÃO: Este aparelho e as suas

partes acessíveis aquecem muito

durante a utilização.

É preciso ter atenção e evitar tocar

os elementos que aquecem.

Manter afastadas as crianças com

menos de 8 anos, caso não estejam

a ser vigiadas.

O presente aparelho pode ser uti-

lizado por crianças com mais de 8

anos e por pessoas com capacida-

des físicas, sensoriais ou mentais

reduzidas ou com pouca experiên-

cia e conhecimentos, caso sejam

adequadamente vigiadas ou caso

tenham recebido instruções em re-

lação ao uso do aparelho de forma

segura e tenham conhecimento dos

perigos associados. As crianças não

devem brincar com o aparelho. As

operações de limpeza e manutenção

não devem ser efectuadas por

crianças sem vigilância.

ATENÇÃO: Deixar um fogão com

gordura e óleo sem vigilância pode

ser perigoso e provocar um incêndio.

NUNCA tente apagar as chamas

com água. É necessário desligar o

aparelho e cobrir as chamas com

uma tampa ou com uma manta

ignífuga.

Não utilizar produtos abrasivos

nem espátulas de metal cortantes

para limpar a porta em vidro do for-

no, uma vez que pode riscar a su-

perfície, provocando a ruptura do

vidro.

As superfícies internas da gaveta (se

presentes) podem ficar muito quen-

tes.

Nunca utilize equipamento de lim-

peza a vapor ou de alta pressão

para limpar o aparelho.

Elimine os líquidos presentes na

tampa antes de abri-la. Não feche a

tampa de vidro (se presente) se os

queimadores ou a chapa eléctrica

ainda estiverem quentes.

ATENÇÃO: Assegure-se de que o

aparelho esteja desligado antes de

substituir a lâmpada, para evitar a

possibilidade de choques eléctricos.

ATENÇÃO: O uso de protecções

do plano inadequadas pode causar

incidentes.

ATENÇÃO

! Quando inserir a grelha, assegure-

-se de que o bloqueio esteja voltado

para cima e na parte posterior da

cavidade.

5

ES

ATENCIÓN: Este aparato y sus partes

accesibles se calientan mucho durante

el uso.

Por lo tanto, es importante evitar tocar

los elementos calentadores.

Mantenga alejados a los niños meno-

res de 8 años si no son continuamente

vigilados.

El presente aparato puede ser utiliza-

do por niños mayores de 8 años y por

personas con capacidades físicas,

sensoriales o mentales disminuidas o

sin experiencia ni conocimientos, si se

encuentran bajo una adecuada vigilan-

cia o si han sido instruidos sobre el uso

del aparato de modo seguro y com-

prenden los peligros relacionados con

el mismo. Los niños no deben jugar

con el aparato. Las operaciones de lim-

pieza y de mantenimiento no deben ser

realizadas por niños sin vigilancia.

ATENCIÓN: Dejar un quemador con

grasas o aceites sin vigilancia puede

ser peligroso y provocar un incendio.

NUNCA intente apagar una llama/in-

cendio con agua, se debe apagar el

aparato y cubrir la llama, por ejemplo,

con una tapa o con una manta ignífu-

ga.

No utilice productos abrasivos ni

espátulas de metal cortantes para

limpiar la puerta de cristal del horno ya

que podrían rayar la superficie y qu-

ebrar el cristal.

Las superficies internas del cajón (cu-

ando existe) pueden calentarse.

No utilice nunca limpiadores a vapor

o de alta presión para la limpieza del

aparato.

Elimine eventuales líquidos presentes

sobre la tapa antes de abrirla. No cierre

la tapa de vidrio (si existe) cuando los

quemadores o la placa eléctrica todavía

están calientes.

ATENCIÓN: Antes de sustituir la lámpa-

ra controle que el aparato esté apagado

para evitar la posibilidad de choques

eléctricos.

ATENCIÓN: el uso de protecciones ina-

propiadas de la placa de cocción puede

provocar accidentes.

ATENCIÓNATENCIÓNATENCIÓN

! Cuando introduzca la parrilla, con-

trole que el tope esté dirigido hacia

arriba y en la parte posterior de la

cavidad.

6

1 Hob burner

2 Hob Grid

3.Control panel

4.Sliding grill rack

5.DRIPPING pan

6.Adjustable foot

7.Containment surface for spills

8.GUIDE RAILS for the sliding racks

9.position 5

10.position 4

11.position 3

12.position 2

13.position 1

Description of the appliance

Overall view

GB

1. Quemador de gas

2.Plano de contención eventuales derrames

3. Panel de mandos

4. Rejilla estante del horno

5. Asadera o plano de cocción

6. Patitas regulables

7. Rejilla del plano de cocción

8. GUÍAS de deslizamiento de las bandejas

9.

POSICIÓN

5

10.

POSICIÓN

4

11.

POSICIÓN 3

12.

POSICIÓN

2

13.

POSICIÓN

1

Descripción del aparato

Vista de conjunto

ES

1. Queimador a gás

2. Grade do piano de trabalho

3. Painel de comandos

4. Prateleira GRADE

5. Prateleira BANDEJA PINGADEIRA

6. Pé de regulação

7. Plano de retenção dos eventuais vazamentos

8. GUIAS de deslizamento das prateleiras

9. Posição 5

10. Posição 4

11.Posição 3

12. Posição 2

13. Posição 1

Descrição do aparelho

Vista de conjunto

PT

1

2

4

5

6

7

9

10

11

12

13

8

3

6

1.Brûleur à gaz

2.Grille du plan de cuisson

3.Tableau de bord

4. Support GRILLE

5. Support LECHEFRITE

6.Pied de réglage

7.Plateau du plan de cuisson

8. GLISSIERES de coulissement

9. niveau 5

10.niveau 4

11.niveau 3

12.niveau 2

13.niveau 1

Description de l’appareil

Vue d’ensemble

FR

7

1

2

3

4

6

Description of the appliance

Control panel

GB

1.THERMOSTAT knob

2.SELECTOR knob

3.THERMOSTAT Indicator light

4.Hob BURNER control knob

6.TIMER knob

Description de l’appareil

Tableau de bord

FR

Descrição do aparelho

Painel de comandos

PT

1.Selector para a temperatura de cozedura (termostato)

3.Indicador de funcionamento termostato

2.Botão selector das funções de cozedura

4.Botão luz do forno e rotisserie

6.Botão contador de minutos.

1.Manette du THERMOSTAT

3.Voyant lumineux THERMOSTAT

2.Manette PROGRAMMES

4.Manette BRULEURS

6.Minuteur

Descripción del aparato

Panel de control

ES

2.Perilla PROGRAMAS

3.La luz piloto del termóstato

4.Perillas de mando de los quemadores

1.Perilla TERMOSTATO

6. Perilla TIMER

5

5.OVEN Indicator light

5.Voyant lumineux FOUR

5.La luz piloto del horno

5.Indicador de funcionamento horno

8

GB

! Before operating your new appliance please read

this instruction booklet carefully. It contains important

information concerning the safe installation and operation

of the appliance.

! Please keep these operating instructions for future

reference. Make sure that the instructions are kept with

the appliance if it is sold, given away or moved.

! The appliance must be installed by a qualified

professional according to the instructions provided.

! Any necessary adjustment or maintenance must be

performed after the cooker has been disconnected from

the electricity supply.

Room ventilation

The appliance may only be installed in permanently-

ventilated rooms, in accordance with current national

legislation. The room in which the appliance is installed

must be ventilated adequately so as to provide as much

air as is needed by the normal gas combustion process

(the flow of air must not be lower than 2 m

3

/h per kW of

installed power).

The air inlets, protected by grilles, should have a duct

with an inner cross section of at least 100 cm

2

and should

be positioned so that they are not liable to even partial

obstruction (see  gure A).

These inlets should be enlarged by 100% - with a

minimum of 200 cm

2

- whenever the surface of the hob

is not equipped with a flame failure safety device. When

the flow of air is provided in an indirect manner from

adjacent rooms (see  gure B), provided that these are

not communal parts of a building, areas with increased

fire hazards or bedrooms, the inlets should be fitted with

a ventilation duct leading outside as described above.

Adjacent room Room requiring ventilation

A B

Ventilation opening Increase in the gap

between

for comburent air the door and the

flooring

Disposing of combustion fumes

The disposal of combustion fumes should be guaranteed

using a hood connected to a safe and efficient natural

suction chimney, or using an electric fan that begins

to operate automatically every time the appliance is

switched on (see  gure).

Fumes channelled Fumes channelled through

Installation

A

! After prolonged use of the appliance, it is advisable to

open a window or increase the speed of any fans used.

straight outside a chimney or a branched

flue system (reserved for

cooking appliances)

! The liquefied petroleum gases are heavier than air and

collect by the floor, therefore all rooms containing LPG

cylinders must have openings leading outside so that

any leaked gas can escape easily.

LPG cylinders, therefore, whether partially or completely

full, must not be installed or stored in rooms or storage

areas that are below ground level (cellars, etc.). Only

the cylinder being used should be stored in the room;

this should also be kept well away from sources of

heat (ovens, chimneys, stoves) that may cause the

temperature of the cylinder to rise above 50°C.

Positioning and levelling

! It is possible to install the appliance alongside

cupboards whose height does not exceed that of the

hob surface.

! Make sure that the wall in contact with the back of the

appliance is made from a non-flammable, heat-resistant

material (T 90°C).

To install the appliance correctly:

• Place it in the kitchen, the dining room or the bed-sit

(not in the bathroom).

• If the top of the hob is higher than the cupboards, the

appliance must be installed at least 600 mm away from

them.

• If the cooker is installed underneath a wall cabinet,

there must be a minimum distance of 420 mm between

this cabinet and the top of the hob.

This distance should be increased to 700 mm if the wall

cabinets are flammable (see  gure).

9

GB

• Do not position blinds

behind the cooker or less

than 200 mm away from

its sides.

• Any hoods must be

installed according to

the instructions listed in

the relevant operating

manual.

Levelling

If it is necessary to level the

appliance, screw the adjustable

feet into the places provided on

each corner of the base of the

cooker (see  gure).

The legs* fit into the slots on the

underside of the base of the

cooker.

Electrical connection

Install a standardised plug corresponding to the load

indicated on the appliance data plate (see Technical data

table).

The appliance must be directly connected to the mains using

an omnipolar circuit-breaker with a minimum contact opening

of 3 mm installed between the appliance and the mains. The

circuit-breaker must be suitable for the charge indicated and

must comply with current electrical regulations (the earthing

wire must not be interrupted by the circuit-breaker). The

supply cable must be positioned so that it does not come

into contact with temperatures higher than 50°C at any point.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated by the data plate.

• The voltage is in the range between the values

indicated on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask

an authorised technician to replace it. Do not use

extension cords or multiple sockets.

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only.

! The manufacturer declines any liability should these

safety measures not be observed.

Gas connection

Connection to the gas network or to the gas cylinder

may be carried out using a flexible rubber or steel hose,

in accordance with current national legislation and after

making sure that the appliance is suited to the type of gas

with which it will be supplied (see the rating sticker on

the cover: if this is not the case see below). When using

liquid gas from a cylinder, install a pressure regulator

which complies with current national regulations. To

make connection easier, the gas supply may be turned

sideways*: reverse the position of the hose holder with

that of the cap and replace the gasket that is supplied

with the appliance.

! Check that the pressure of the gas supply is consistent

with the values indicated in the Table of burner and

nozzle specifications (see below). This will ensure the

safe operation and durability of your appliance while

maintaining efficient energy consumption.

Gas connection using a flexible rubber hose

Make sure that the hose complies with current national

legislation. The internal diameter of the hose must

measure: 8 mm for liquid gas supply; 13 mm for methane

gas supply.

Once the connection has been performed, make sure

that the hose:

• Does not come into contact with any parts that reach

temperatures of over 50°C.

• Is not subject to any pulling or twisting forces and that

it is not kinked or bent.

• Does not come into contact with blades, sharp corners

or moving parts and that it is not compressed.

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will be fixed

using clamps that comply with current regulations.

10

GB

! If one or more of these conditions is not fulfilled or if

the cooker must be installed according to the conditions

listed for class 2 - subclass 1 appliances (installed

between two cupboards), the flexible steel hose must

be used instead (see below).

Connecting a flexible jointless stainless steel pipe to

a threaded attachment

Make sure that the hose and gaskets comply with current

national legislation.

To begin using the hose, remove the hose holder on the

appliance (the gas supply inlet on the appliance is a

cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres, making

sure that the hose is not compressed and does not come

into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the hose

fittings for leaks using a soapy solution. Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other

than the default type (this is indicated on the rating label

on the cover).

3. While the burner is alight, quickly change the position

of the knob from minimum to maximum and vice versa

several times, checking that the flame is not extinguished.

! The hob burners do not require primary air adjustment.

! After adjusting the appliance so it may be used with a

different type of gas, replace the old rating label with a

new one that corresponds to the new type of gas (these

labels are available from Authorised Technical Assistance

Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner

(see  gure), and replace them with nozzles suited to the

new type of gas (see Burner and nozzle speci cations table).

3. Replace all the components by following the above

instructions in reverse.

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust

the regulatory screw, which is

positioned inside or next to the

tap pin, until the flame is small

but steady.

! If the appliance is connected to

a liquid gas supply, the regulatory

screw must be fastened as tightly

as possible:

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of

their housing. The burner consists of two separate

parts (see pictures).

2. Unscrew the nozzles using a 7 mm socket spanner.

Replace the nozzles with models that are configured

for use with the new type of gas (see Table 1). The two

nozzles have the same hole diameter.

3. Replace all the components by completing the above

operations in reverse order.

• Adjusting the burners’ primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust the adjustment screw,

which is positioned in or next to the tap pin, until the

flame is small but steady.

3. Having adjusted the flame to the required low setting,

while the burner is alight, quickly change the position

of the knob from minimum to maximum and vice versa

several times, checking that the flame does not go out

4. Some appliances have a safety device (thermocouple)

fitted. If the device fails to work when the burners are

set to the low flame setting, increase this low flame

setting using the adjusting screw.

11

GB

Table of burner and nozzle specifications

Safety Chain

! In order to prevent accidental tipping of the appliance,

for example by a child climbing onto the oven door, the

supplied safety chain MUST be installed!

The cooker is fitted with a safety chain to be fixed by

means of a screw (not supplied with the cooker) to the

wall behind the appliance, at the same height as the chain

is attached to the appliance.

Choose the screw and the screw anchor according to

the type of material of the wall behind the appliance. If

the head of the screw has a diameter smaller than 9mm,

a washer should be used. Concrete wall requires the

screw of at least 8mm of diameter, and 60mm of length.

Ensure that the chain is fixed to the rear wall of the cooker

and to the wall, as shown in figure, so that after installation

it is tensioned and parallel to the ground level.

S

R

TC A

5. Once the adjustment has been made, replace the seals

on the by-passes using sealing wax

! If the appliance is connected to liquid gas, the regulation

screw must be fastened as tightly as possible.

! Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Stickers are available from any of our Service Centres.

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet pipe (in order

to comply with current national regulations).

87

69

50

128

104

78

51

Tripple Ring (TC)

236 232 2x99 309

130

3.25 1.50 2x65

63

58

A6TMH2AF EXA6TMH2AF EXA6TMH2AF EX

12

GB

Start-up and use

Using the hob

Lighting the burners

For each BURNER knob there is a complete ring showing

the strength of the flame for the relevant burner.

To light one of the burners on the hob:

1. Bring a flame or gas lighter close to the burner.

2. Press the BURNER knob and turn it in an anticlockwise

direction so that it is pointing to the maximum flame

setting .

3. Adjust the intensity of the flame to the desired level by

turning the BURNER knob in an anticlockwise direction. This

may be the minimum setting , the maximum setting  or

any position in between the two.

If the appliance is fitted with an

electronic lighting device* (see

 gure), press the ignition button,

marked with the symbol



, then

hold the BURNER knob down

and turn it in an anticlockwise

direction, towards the maximum

flame setting, until the burner

is lit.The burner may be extinguished when the knob is

released. If this occurs, repeat the operation, holding the

knob down for a longer period of time.

! If the flame is accidentally extinguished, switch off the

burner and wait for at least 1 minute before attempting

to relight it.

If the appliance is equipped with a flame failure

safety device*, press and hold the BURNER knob for

approximately 2-3 seconds to keep the flame alight and

to activate the device.

To switch the burner off, turn the knob until it reaches

the stop position •.

Flame adjustment according to levels

the burner flame intensity can be adjusted with the

knob according to 6 power levels, from maximum

to minimum with 4 intermediate positions:

a click will indicate the change from one level to

another when turning the knob. The system

guarantees a more precise adjustment, allows

to replicate the flame intensity and to identify

easily the preferred level for different cooking

operations.

*

Only available in certain models.

Practical advice on using the burners

For the burners to work in the most efficient way possible

and to save on the amount of gas consumed, it is

recommended that only pans that have a lid and a flat

base are used. They should also be suited to the size of

the burner:

To identify the type of burner, please refer to the diagrams

contained in the “Burner and nozzle specifications”.

! For models equipped with a reducer grid, the latter must

be used only for the auxiliary burner, when pans with a

diameter of less than 12 cm are used.

Using the oven

! The first time you use your appliance, heat the empty

oven with its door closed at its maximum temperature

for at least half an hour. Ensure that the room is well

ventilated before switching the oven off and opening the

oven door. The appliance may emit a slightly unpleasant

odour caused by protective substances used during the

manufacturing process burning away.

! Before operating the product, remove all plastic film

from the sides of the appliance.

! Never put objects directly on the bottom of the oven; this

will avoid the enamel coating being damaged.

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. Select the recommended temperature for the

cooking mode or the desired temperature by turning the

THERMOSTAT knob.

A list detailing cooking modes and suggested cooking

temperatures can be found in the relevant table (see Oven

cooking advice table).

During cooking it is always possible to:

• Change the cooking mode by turning the SELECTOR

knob.

• Change the temperature by turning the THERMOSTAT

knob.

Burner Cookware Diameter (cm)

Fast (R) 24 - 26

Semi Fast (S) 16 - 20

Auxiliary (A) 10 - 14

Triple Crown (TC) 24 - 26

13

GB

• Stop cooking by turning the SELECTOR knob to the

“0” position.

! Always place cookware on the rack(s) provided.

THERMOSTAT indicator light

When this is illuminated, the oven is generating heat.

It switches off when the inside of the oven reaches the

selected temperature. At this point the light illuminates

and switches off alternately, indicating that the thermostat

is working and is maintaining the temperature at a

constant level.

Oven light

This is switched on by turning the SELECTOR knob to

any position other than “0”. It remains lit as long as the

oven is operating. By selecting



with the knob, the

light is switched on without any of the heating elements

being activated.

Cooking modes

! A temperature value can be set for all cooking modes

between 60°C and Max, except for the following modes

• GRILL (recommended: set only to MAX power level)

• GRATIN (recommended: do not exceed 200°C).



TRADITIONAL OVEN mode

Both the top and bottom heating elements will come on.

When using this traditional cooking mode, it is best to use

one cooking rack only. If more than one rack is used, the

heat will be distributed in an uneven manner.



BAKING mode

The rear heating element and the fan are switched on,

thus guaranteeing the distribution of heat in a delicate and

uniform manner throughout the entire oven. This mode is

ideal for baking and cooking temperature sensitive foods

(such as cakes that need to rise) and for the preparation

of pastries on 3 shelves simultaneously.



FAST COOKING mode

The heating elements and the fan come on, guaranteeing

the distribution of heat consistently and uniformly

throughout the oven.

Preheating is not necessary for this cooking mode. This

mode is particularly suitable for cooking pre-packed

food quickly (frozen or pre-cooked). The best results are

achieved using one cooking rack only.



MULTI-COOKING mode

All the heating elements (top, bottom and circular) switch

on and the fan begins to operate. Since the heat remains

constant throughout the oven, the air cooks and browns

food in a uniform manner. A maximum of two racks may

be used at the same time.





PIZZA mode

The circular heating elements and the elements at

the bottom of the oven are switched on and the fan is

activated. This combination heats the oven rapidly by

producing a considerable amount of heat, particularly

from the element at the bottom. If you use more than one

rack at a time, switch the position of the dishes halfway

through the cooking process.



GRILL mode

The central part of the top heating element is switched

on. The high and direct temperature of the grill is

recommended for food that requires a high surface

temperature (veal and beef steaks, fillet steak and

entrecôte). This cooking mode uses a limited amount of

energy and is ideal for grilling small dishes. Place the food

in the centre of the rack, as it will not be cooked properly

if it is placed in the corners.



GRATIN

mode

The top heating element and the rotisserie (where

present) are activated and the fan begins to operate.

This combination of features increases the effectiveness

of the unidirectional thermal radiation provided by the

heating elements through forced circulation of the air

throughout the oven. This helps prevent food from burning

on the surface and allows the heat to penetrate right into

the food.

! The GRILL and GRATIN cooking modes must be

performed with the oven door shut.

DEFROSTING mode

The fan located on the bottom of the oven makes the air

circulate at room temperature around the food. This is

recommended for the defrosting of all types of food, but in

particular for delicate types of food which do not require

heat, such as for example: ice cream cakes, cream or

custard desserts, fruit cakes. By using the fan, the

defrosting time is approximately halved. In the case of

meat, fish and bread, it is possible to accelerate the

process using the “multi-cooking” mode and setting the

temperature to 80° - 100°C.





14

GB

BOTTOM VENTILATED mode

The bottom heating element and the fan is activated,

which allows for the heat distribution within the whole

cavity of the oven. This combination is useful for light

cooking of vegetables and fish.

BOTTOM mode :

The lower heating element is activated. This position

is recommended for perfecting the cooking of dishes

(in baking trays) which are already cooked on the

surface but require further cooking in the centre, or

for desserts with a covering of fruit or jam, which only

require moderate colouring on the surface. It should

be noted that this function does not allow the maximum

temperature to be reached inside the oven (250°C)

and it is therefore not recommended that foods are

cooked using only this setting, unless you are baking

cakes (which should be baked at a temperature of

180°C or lower).

Practical cooking advice

! In the GRILL cooking mode, place the dripping pan in

position 1 to collect cooking residues (fat and/or grease).

GRILL

• Insert the rack in position 3 or 4. Place the food in the

centre of the rack.

• We recommend that the power level is set to maximum.

The top heating element is regulated by a thermostat

and may not always operate constantly.

PIZZA

• Use a light aluminium pizza pan. Place it on the rack

provided.

For a crispy crust, do not use the dripping pan as it

prevents the crust from forming by extending the total

cooking time.

• If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza

halfway through the cooking process.

WARNING! The oven is provided with

a stop system to extract the racks and

prevent them from coming out of the

oven.(1)

As shown in the drawing, to extract

them completely, simply lift the racks,

holding them on the front part, and

pull (2).

Cooking Control Timer Knob

Some models are equipped with a timer program to

control when the oven shuts off during cooking. To use

this feature, you must wind the knob one full turn in the

counter-clockwise direction ; Then, turn the knob in

the clockwise direction

, to set the time by matching

up the indicator on the control panel with the number

of minutes on the knob.

At the end of the programmed length of time, the timer

will sound and automatically turn off the oven.

Attention: to use the oven in manual mode without the

cooking control timer, match the indicator on the

control panel with the

symbol on the timer knob.

When the oven is not in use, the cooking control timer

can be used like a normal timer.

15

GB

Oven cooking advice table

Cooking

modes

Foods Weight

(in kg)

Rack Position Pre-heating

time

(minutes)

Recommended

temperature

Cooking

time

(minutes)

Traditional

Oven

Duck

Roast veal or beef

Pork roast

Biscuits (short pastry)

Tarts

1

-

1

3

15

200

180

65-75

70-75

70-80

15-20

30-35

Baking

Mode

Tarts

Fruit cakes

Plum cake

Sponge cake

Stuffed pancakes (on 2 racks)

Small cakes (on 2 racks)

Cheese puffs (on 2 racks)

Cream puffs (on 3 racks)

Biscuits (on 3 racks)

Meringues (on 3 racks)

0.5

1

0.7

0.5

1.2

0.6

0.4

0.7

0.5

3

2 or 3

3

2 and 4

1 and 3 and 5

15

180

160

200

190

210

180

90

20-30

40-45

40-50

25-30

30-35

20-25

15-20

20-25

180

Frozen food

Pizza

Courgette and prawn pie

Country style spinach pie

Turnovers

Lasagne

Golden Rolls

Chicken morsels

0.3

0.4

0.5

0.3

0.5

0.4

2

-

250

200

220

200

180

220

12

20

30-35

25

35

25-30

15-20

Pre-cooked food

Golden chicken wings

0.4

2

-

200

20-25

Fast

cooking

Fresh Food

Biscuits (short pastry)

Plum cake

Cheese puffs

0.3

0.6

0.2

2

-

200

180

210

15-18

45

10-12

Multi-

cooking

Pizza (on 2 racks)

Lasagne

Lamb

Roast chicken + potatoes

Mackerel

Plum cake

Cream puffs (on 2 racks)

Biscuits (on 2 racks)

Sponge cake (on 1 rack)

Sponge cake (on 2 racks)

Savoury pies

1

1+1

1

0.5

1

1.5

2 and 4

3

2

2 and 4

2

2 and 4

2

2 and 4

3

15

10

15

10

15

230

180

200

180

170

190

180

170

200

15-20

30-35

40-45

60-70

30-35

40-50

20-25

10-15

15-20

20-25

25-30

Pizza Mode

Pizza

Roast veal or beef

Chicken

0.5

1

3

2

2 or 3

15

10

220

180

15-20

25-30

60-70

Soles and cuttlefish

Squid and prawn kebabs

Cuttlefish

Cod filet

Grilled vegetables

Veal steak

Sausages

Hamburgers

Mackerels

Toasted sandwiches (or toast)

0.7

0.6

0.8

0.4

0.8

0.6

1

4 and 6

4

3 or 4

4

-

Max

10-12

8-10

10-15

15-20

10-12

15-20

3-5

Gratin

Grilled chicken

Cuttlefish

1.5

2

10

200

55-60

30-35

Bottom

Ventilated

Bottom

For perfecting cooking

Bottom

Ventilated

Bottom

Grill

16

GB

Precautions and tips

! This appliance has been designed and manufactured

in compliance with international safety standards.

The following warnings are provided for safety reasons

and must be read carefully.

General safety

• The appliance was designed for domestic use inside

the home and is not intended for commercial or

industrial use.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

• Do not touch the appliance with bare feet or with wet

or damp hands and feet.

• The appliance must be used by adults only for

the preparation of food, in accordance with the

instructions outlined in this booklet. Any other

use of the appliance (e.g. for heating the room)

constitutes improper use and is dangerous.

The manufacturer may not be held liable for any

damage resulting from improper, incorrect and

unreasonable use of the appliance.

• The instruction booklet accompanies a class 1

(insulated) or class 2 - subclass 1 (recessed between

2 cupboards) appliance.

• Do not touch the heating elements or certain parts

of the oven door when the appliance is in use;

these parts become extremely hot. Keep children

well away from the appliance.

• Make sure that the power supply cables of other

electrical appliances do not come into contact with

the hot parts of the oven.

• The openings used for the ventilation and dispersion

of heat must never be covered.

• Always use oven gloves when placing cookware in the

oven or when removing it.

• Do not use flammable liquids (alcohol, petrol, etc...)

near the appliance while it is in use.

• Do not place flammable material in the lower storage

compartment or in the oven itself. if the appliance is

switched on accidentally, they could catch fire.

• The internal surfaces of the compartment (where

present) may become hot.

• Always make sure the knobs are in the

• position when

the appliance is not in use.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from the

electricity mains.

• If the appliance breaks down, under no circumstances

should you attempt to perform the repairs yourself.

Repairs carried out by inexperienced persons may

cause injury or further malfunctioning of the appliance.

Contact Assistance.

• Do not rest heavy objects on the open oven door.

• The appliance should not be operated by people

(including children) with reduced physical, sensory

or mental capacities, by inexperienced individuals or

by anyone who is not familiar with the product. These

individuals should, at the very least, be supervised

by someone who assumes responsibility for their

safety or receive preliminary instructions relating to

the operation of the appliance.

• Do not let children play with the appliance.

•If the cooker is placed on a pedestal, take the necessary

precautions to prevent the cooker from sliding off the

pedestal itself.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health. The crossed-

out dustbin is marked on all products to remind the

owner of their obligations regarding separated waste

collection.

For further information relating to the correct disposal of

exhausted household appliances, owners may contact

the public service provided or their local dealer.

Respecting and conserving the

environment

• You can help to reduce the peak load of the electricity

supply network companies by using the oven in the

hours between late afternoon and the early hours of

the morning.

• Always keep the oven door closed when using the

GRILL and DOUBLE GRILL modes. This will achieve

better results while saving energy (approximately

10%).

• Check the door seals regularly and wipe them clean

to ensure they are free of debris so that they adhere

properly to the door, thus avoiding heat dispersion.

17

GB

Switching the appliance off

Disconnect your appliance from the electricity supply

before carrying out any work on it.

Cleaning the appliance

! Never use steam cleaners or pressure cleaners on the

appliance.

• The stainless steel or enamel-coated external parts and

the rubber seals may be cleaned using a sponge that

has been soaked in lukewarm water and neutral soap.

Use specialised products for the removal of stubborn

stains. After cleaning, rinse well and dry thoroughly.

Do not use abrasive powders or corrosive substances.

• The hob grids, burner caps, flame spreader rings and

burners may be removed to make cleaning easier;

wash them in hot water and non-abrasive detergent,

making sure all burnt-on residue is removed before

drying them thoroughly.

• Clean the terminal part of the flame failure safety

devices* frequently.

• The inside of the oven should ideally be cleaned after

each use, while it is still lukewarm. Use hot water and

detergent, then rinse well and dry with a soft cloth. Do

not use abrasive products.

• Clean the glass part of the oven door using a sponge

and a non-abrasive cleaning product, then dry

thoroughly with a soft cloth. Do not use rough abrasive

material or sharp metal scrapers as these could

scratch the surface and cause the glass to crack.

• The accessories can be washed like everyday

crockery, and are even dishwasher safe.

• Do not close the cover when the burners are alight or

when they are still hot.

Inspecting the oven seals

Check the door seals around the oven regularly. If

the seals are damaged, please contact your nearest

Authorised After-sales Service Centre. We recommend

that the oven is not used until the seals have been

replaced.

Replacing the oven light bulb

1. After disconnecting the oven

from the electricity mains, remove

the glass lid covering the lamp

socket (see  gure).

2. Remove the light bulb and

replace it with a similar one:

voltage 230 V, wattage 25 W,

cap E 14.

3. Replace the lid and reconnect

the oven to the electricity supply.

! Do not use the oven lamp as/for ambient lighting.

Gas tap maintenance

Over time, the taps may become jammed or difficult to

turn. If this occurs, the tap must be replaced.

! This procedure must be performed by a qualified

technician authorised by the manufacturer.

Assistance

! Never use the services of an unauthorised technician.

Please have the following information to hand:

• The type of problem encountered.

• The appliance model (Mod.).

• The serial number (S/N).

The latter two pieces of information can be found on the

data plate located on the appliance.

Care and maintenance

Removing and fitting the oven door:

1.Open the door

2.Make the hinge clamps of the oven door rotate

backwards completely (see photo)

3.Close the door until the clamps stop (the door will

remain open for 40° approx.) (see photo)

18

GB

40°

4.Press the two buttons on the upper profile and

extract the profile (see photo)

5.Remove the glass sheet and do the cleaning as

indicated in chapter: "Care and maintenance".

6.Replace the glass.

WARNING! Oven must not be operated with inner

door glass removed!

WARNING! When reassembling the inner door

glass insert the glass panel correctly so that the

text written on the panel is not reversed and

can be easily legible.

7.Replace the profile, a click will indicate that the

part is positioned correctly.

8.Open the door completely.

9.Close the supports (see photo).

10.Now the door can be completely closed and the

oven can be started for normal use.

Steam-Assisted Oven Cleaning

This method of cleaning is recommended especially after

cooking very fatty (roasted)meats.

This cleaning process allows to facilitate the removal of

dirt of the walls of the oven by the generation of steam

that is created inside the oven cavity for easier cleaning.

! Important! Before you start steam -cleaning:

-Remove any food residue and grease from the bottom

of the oven.

- Remove any oven accessories (grids and drip pans).

Perform the above operations according to the following

procedure:

1. pour 300ml of water into the baking tray in the oven,

placing it in the bottom shelf. In the models where the

drip pan is not present, use a baking sheet and place it

on the grill at the bottom shelf;

2. select the function of the oven

and set the temperature to 100 ° C;

3. keep it in the oven for 15min;

4. turn off the oven;

5. Once cooled the oven, you can open the door to

complete the cleaning with water and a damp cloth;

6. eliminate any residual water from the cavity after

finishing cleaning

When the steam –cleaning is done, after cooking

especially fatty foods, or when grease is difficult to

remove, you may need to complete the cleaning with the

traditional method, described in the previous paragraph.

! Perform cleaning only in the cold oven!

BOTTOM

19

FR

! Conservez ce mode d’emploi pour pouvoir le consulter

à tout moment. En cas de vente, de cession ou de

déménagement, veillez à ce qu’il suive l’appareil.

! Lisez attentivement les instructions : elles contiennent

des conseils importants sur l’installation, l’utilisation et la

sécurité de votre appareil.

! L’installation de l’appareil doit être effectuée par un

professionnel du secteur conformément aux instructions

du fabricant.

! N’importe quelle opération de réglage, d’entretien, etc.,

doit être effectuée après avoir débranché la prise de la

cuisinière.

Aération des locaux

L’appareil doit être installé dans des locaux qui sont

aérés en permanence, selon les prescriptions des

Normes en vigueur dans le pays d’installation. Il est

indispensable que la pièce où l’appareil est installé

dispose d’une quantité d’air égale à la quantité d’air

comburant nécessaire à une bonne combustion du

gaz (le flux d’air doit être d’au moins 3 m

3

/h par kW de

puissance installée).

Les prises d’air, protégées par des grilles, doivent

disposer d’un conduit d’au moins 2 cm2 de section

utile et dans une position qui leur évite tout risque d’être

bouchées accidentellement, même partiellement (voir

figure A).

Ces ouvertures doivent être agrandies de 100% (surface

minimale 2 cm2) en cas d’appareils dépourvus du

dispositif de sécurité de flamme et quand l’afflux de l’air

provient de manière indirecte de pièces voisines (voir

figure B) – à condition qu’il ne s’agisse pas de parties

communes du bâtiment, de chambres à coucher ou

de locaux à risque d’incendie – équipées d’un conduit

d’aération avec l’extérieur comme décrit plus haut.

Local adjacent Local à ventiler

A

Ouverture de ventilation Agrandissement de la fissure

pour l’air comburant entre la porte et le sol

Fig. A Fig. B

! Après une utilisation prolongée de l’appareil, il est

conseillé d’ouvrir une fenêtre ou d’augmenter la vitesse

de ventilateurs éventuels.

Evacuation des fumées de combustion

La pièce doit prévoir un système d’évacuation vers

l’extérieur des fumées de combustion réalisé au moyen

d’une hotte reliée à une cheminée à tirage naturel ou

par ventilateur électrique qui entre automatiquement en

fonction dès qu’on allume l’appareil (voir figures).

Evacuation directement Evacuation par cheminée ou conduit

à l’extérieur de fumée ramifié (réservé

aux

appareils de cuisson)

! Les gaz de pétrole liquéfiés, plus lourds que l’air,

se déposent et stagnent dans le bas. Les locaux qui

contiennent des bouteilles de G.P.L doivent donc prévoir

des ouvertures vers l’extérieur afin de permettre l’évacuation

du gaz par le bas en cas de fuites accidentelles. Ne pas

installer ou entreposer de bouteilles de GPL, vides ou

partiellement pleines, dans des locaux qui se trouvent

en sous-sol (caves etc.). Ne gardez dans la pièce que la

bouteille que vous êtes en train d’utiliser, loin de sources

de chaleur (fours, feux de bois, poêles etc.) qui pourraient

amener sa température à plus de 50°C.

Positionnement et nivellement

! L’appareil peut être installé à côté de meubles dont la

hauteur ne dépasse pas celle du plan de cuisson.

! Assurez-vous que le mur en contact avec la paroi arrière

de l’appareil est réalisée en matériel ignifuge résistant à

la chaleur (T 90°C).

Pour une installation correcte :

• installez cet appareil dans une cuisine, une salle à

manger ou un studio (jamais dans une salle de bains);

• si le plan de cuisson de la cuisinière dépasse le plan de

travail des meubles, ces derniers doivent être placés

à au moins 600 mm de l’appareil;

• si la cuisinière est installée sous un élément suspendu,

il faut que ce dernier soit placé à au moins 420mm de

distance du plan. Il faut prévoir une distance de 700mm

Installation

FR

20

si les éléments suspendus

sont inflammables (voir

 gure);

• ne placez pas

de rideaux derrière la

cuisinière ou sur ses

côtés à moins de 200

mm de distance;

• pour l’installation de

hottes, conformez-vous

aux instructions de leur notice d’emploi.

Nivellement

Pour mettre l’appareil bien à

plat, vissez les pieds de réglage

fournis aux emplacements

prévus aux coins à la base de la

cuisinière (voir figure).

Montage des pieds* par

encastrement sous la base.

Raccordement électrique

Montez sur le câble une prise normalisée pour la charge

indiquée sur l’étiquette des caractéristiques (voir tableau

des caractéristiques techniques).

En cas de raccordement direct au réseau, il faut intercaler

entre l’appareil et le réseau un interrupteur à coupure

omnipolaire ayant au moins 3 mm d’écartement entre

les contacts, dimensionné à la charge et conforme

aux normes NFC 15-100 (le fil de terre ne doit pas être

interrompu par l’interrupteur). Le câble d’alimentation

ne doit atteindre, en aucun point, des températures

dépassant de 50°C la température ambiante.

Avant de procéder au branchement, assurez-vous que :

• la prise est bien munie d’une terre conforme à la loi;

• la prise est bien apte à supporter la puissance

maximale de l’appareil, indiquée sur la plaquette

signalétique;

• la tension d’alimentation est bien comprise entre les

valeurs indiquées sur la plaquette signalétique;

• la prise est bien compatible avec la fiche de l’appareil.

Si ce n’est pas le cas, remplacez la prise ou la fiche,

n’utilisez ni rallonges ni prises multiples.

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

! Après installation de l’appareil, le câble électrique et

la prise de courant doivent être facilement accessibles

! Le câble ne doit être ni plié ni excessivement écrasé.

! Le câble doit être contrôlé périodiquement et ne peut

être remplacé que par un technicien agréé.

! Nous déclinons toute responsabilité en cas de non

respect des normes énumérées ci-dessus.

Raccordement gaz

Pour raccorder l’appareil au réseau de distribution

du gaz ou à la bouteille de gaz utilisez un tuyau

flexible en caoutchouc ou en acier, conformément à la

réglementation en vigueur. Assurez-vous auparavant

que l’appareil est bien réglé pour le type de gaz

d’alimentation utilisé (voir étiquette sur le couvercle :

autrement voir ci-dessous). Si l’alimentation s’effectue avec

du gaz liquide en bouteille, utilisez des régulateurs de

pression conformes à la réglementation en vigueur dans

le pays. Pour simplifier le raccordement, l’alimentation

du gaz est orientable latéralement* : inversez l’about

annelé avec le bouchon de fermeture et remplacez le

joint d’étanchéité (fourni avec l’appareil).

! Pour un fonctionnement en toute sécurité, pour un

meilleur emploi de l’énergie et une plus longue durée de

vie de l’appareil, vérifiez que la pression d’alimentation

respecte bien les valeurs indiquées dans le tableau

Caractéristiques des brûleurs et des injecteurs (voir

ci-dessous).

Raccordement gaz par tuyau flexible en caoutchouc

Assurez-vous que le tuyau est bien conforme aux normes

applicables dans le pays d’installation. Le tuyau doit avoir

un diamètre intérieur de : 8 mm en cas d’alimentation au

gaz liquide; 15 mm en cas d’alimentation au gaz naturel.

Après avoir effectué le raccordement, assurez-vous que

le tuyau :

• ne touche en aucun point à des parties pouvant

atteindre plus de 50°C;

• ne soit pas soumis à traction ou torsion et ne présente

pas de pliures ou étranglements;

• ne risque pas d’entrer en contact avec des corps

tranchants, des arêtes vives, des parties mobiles et

ne soit pas écrasé;

• puisse être facilement contrôlable sur toute sa

longueur pour vérifier son état de conservation;

• ait moins de 1500mm de long;

• soit bien fixé à ses deux extrémités à l’aide de

bagues de serrage conformes à la réglementation

en vigueur dans le pays.

*N’existe que sur certains modèles

La page charge ...

Ariston A6TMH2AF (X) EX Mode d'emploi

Ariston A6TMH2AF (X) EX Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents