Ariston A6TMH2AF (X) EX Mode d'emploi

Catégorie
Fours
Taper
Mode d'emploi
English
GB
Operating Instructions
COOKER AND OVEN
Contents
Operating Instructions,1
WARNING,2
Description of the appliance-Overall view,6
Description of the appliance-Control Panel,7
Installation,8
Start-up and use,12
Cooking modes,13
Using the hob,12
Precautions and tips,16
Care and maintenance,17
Assistance,17
FR
Français
Mode d’emploi
CUISINIERE ET FOUR
Sommaire
Mode d’emploi,1
ATTENTION,3
Description de l’appareil-Vue d’ensemble, 6
Description de l’appareil-Tableau de bord, 7
Installation,19
Mise en marche et utilisation,24
Utilisation du plan de cuisson,24
Précautions et conseils, 28
Nettoyage et entretien,29
Assistance,29
PT
Português
Instruções para a utilização
FOGÃO E FORNO
Índice
Instruções para a utilização,1
ATTENTACAO,4
Descrição do aparelho-Vista de conjunto,6
Descriçao do aparelho-Painel de comandos,7
Instalaçao,31
Início e utilizaçao, 36
Utilizaçao do plano de cozedura,36
Utilizaçao do forno,37
Precauçoes e conselhos,40
Manutençao e cuidados,41
Assistencia técnica,41
EnglishEnglish
A6TMH2AF EX
Español
ES
Manual de instrucciones
COCINA Y HORNO
Sumario
Manual de instrucciones,1
Descripción del aparato-Vista de conjunto,6
Descripción del aparato-Panel de control,7
Instalación,43
Puesta en funcionamiento y uso,48
Precauciones y consejos,52
Mantenimiento y cuidados,53
Asistencia,53
ATTENTION,5
Programmes du four,25
AR
A6TMH2AF EXA6TMH2AF EX
2
WARNING: The appliance and its
accessible parts become hot during
use.
Care should be taken to avoid
touching heating elements.
Children less than 8 years of
age shall be kept away unless
continuously supervised.
This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe
way and understand the hazards
involved. Children shall not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
WARNING: Unattended cooking on a
hob with fat or oil can be dangerous
and may result in fire.
NEVER try to extinguish a fire with
water, but switch off the appliance
and then cover flame e.g. with a lid
or a fire blanket.
Do not use harsh abrasive cleaners
or sharp metal scrapers to clean
the oven door glass since they can
scratch the surface, which may result
in shattering of the glass.
The internal surfaces of the
compartment (where present) may
become hot.
Never use steam cleaners or
pressure cleaners on the appliance.
Remove any liquid from
the lid before opening it.
Do not close the glass cover (if
present) when the gas burners or
electric hotplates are still hot.
WARNING: Ensure that the appliance
is switched off before replacing
the lamp to avoid the possibility of
electric shock.
CAUTION: the use of inappropriate
hob guards can cause accidents.
GB
WARNING
! When you place the rack inside,
make sure that the stop is directed
upwards and in the back of the cavity.
3
FR
ATTENTION: cet appareil ainsi que
ses parties accessibles deviennent
très chauds pendant leur fonctionne-
ment.
Il faut faire attention de ne pas tou-
cher les éléments chauffants.
Ne laisser s’approcher les enfants
de moins de 8 ans à moins qu’ils ne
soient sous surveillance constante.
Le présent appareil peut être utilisé
par des enfants de plus de 8 ans et
par des personnes présentant des
capacités physiques, sensorielles
ou mentales réduites ou n’ayant pas
l’expérience ou les connaissances
nécessaires, à condition qu’ils soient
sous bonne surveillance ou qu’ils
aient reçu les instructions nécessai-
res pour une utilisation de l’appareil
en toute sécurité et à condition qu’ils
se rendent compte des dangers
encourus. Les enfants ne doivent
pas jouer avec l’appareil. Les opéra-
tions de nettoyage et d’entretien ne
doivent pas être effectuées par des
enfants non surveillés.
ATTENTION: laisser un récipient de
cuisson contenant de l’huile ou de la
graisse sur le foyer est dangereux et
risque d’entraîner un incendie.
Il ne faut JAMAIS essayer d’éteindre
une flamme ou un incendie avec de
l’eau! Il faut éteindre l’appareil et
couvrir la flamme avec un couvercle,
par exemple, ou avec une couverture
anti-feu.
Ne pas utiliser de produits abrasifs
ni de spatules métalliques coupan-
tes pour nettoyer la porte du four en
verre, sous peine d’érafler la surface
et de briser le verre.
Les surfaces intérieures du tiroir (s’il
y en a un) peuvent devenir chaudes.
Ne jamais nettoyer l’appareil avec
des nettoyeurs vapeur ou haute pres-
sion.
Essuyer tout liquide pouvant se
trouver sur le couvercle avant de
l’ouvrir. Ne pas abaisser le couvercle
en verre (s’il y en a un) tant que les
brûleurs gaz ou la plaque électrique
sont chauds.
ATTENTION: s’assurer que l’appareil
est éteint avant de procéder au rem-
placement de l’ampoule, afin d’éviter
tout risque d’électrocution.
ATTENTION: l’utilisation de protec-
tions de table inappropriées peut
causer des incendies.
ATTENTION
Lors de l’introduction de la grille,
s’assurer que l’arrêt est bien tourné
vers le haut et se trouve dans la par-
tie arrière de l’enceinte.
Lors de l’introduction de la grille,
s’assurer que l’arrêt est bien tourné
vers le haut et se trouve dans la par-
tie arrière de l’enceinte.
4
PT
ATENÇÃO: Este aparelho e as suas
partes acessíveis aquecem muito
durante a utilização.
É preciso ter atenção e evitar tocar
os elementos que aquecem.
Manter afastadas as crianças com
menos de 8 anos, caso não estejam
a ser vigiadas.
O presente aparelho pode ser uti-
lizado por crianças com mais de 8
anos e por pessoas com capacida-
des físicas, sensoriais ou mentais
reduzidas ou com pouca experiên-
cia e conhecimentos, caso sejam
adequadamente vigiadas ou caso
tenham recebido instruções em re-
lação ao uso do aparelho de forma
segura e tenham conhecimento dos
perigos associados. As crianças não
devem brincar com o aparelho. As
operações de limpeza e manutenção
não devem ser efectuadas por
crianças sem vigilância.
ATENÇÃO: Deixar um fogão com
gordura e óleo sem vigilância pode
ser perigoso e provocar um incêndio.
NUNCA tente apagar as chamas
com água. É necessário desligar o
aparelho e cobrir as chamas com
uma tampa ou com uma manta
ignífuga.
Não utilizar produtos abrasivos
nem espátulas de metal cortantes
para limpar a porta em vidro do for-
no, uma vez que pode riscar a su-
perfície, provocando a ruptura do
vidro.
As superfícies internas da gaveta (se
presentes) podem ficar muito quen-
tes.
Nunca utilize equipamento de lim-
peza a vapor ou de alta pressão
para limpar o aparelho.
Elimine os líquidos presentes na
tampa antes de abri-la. Não feche a
tampa de vidro (se presente) se os
queimadores ou a chapa eléctrica
ainda estiverem quentes.
ATENÇÃO: Assegure-se de que o
aparelho esteja desligado antes de
substituir a lâmpada, para evitar a
possibilidade de choques eléctricos.
ATENÇÃO: O uso de protecções
do plano inadequadas pode causar
incidentes.
ATENÇÃO
! Quando inserir a grelha, assegure-
-se de que o bloqueio esteja voltado
para cima e na parte posterior da
cavidade.
5
ES
ATENCIÓN: Este aparato y sus partes
accesibles se calientan mucho durante
el uso.
Por lo tanto, es importante evitar tocar
los elementos calentadores.
Mantenga alejados a los niños meno-
res de 8 años si no son continuamente
vigilados.
El presente aparato puede ser utiliza-
do por niños mayores de 8 años y por
personas con capacidades físicas,
sensoriales o mentales disminuidas o
sin experiencia ni conocimientos, si se
encuentran bajo una adecuada vigilan-
cia o si han sido instruidos sobre el uso
del aparato de modo seguro y com-
prenden los peligros relacionados con
el mismo. Los niños no deben jugar
con el aparato. Las operaciones de lim-
pieza y de mantenimiento no deben ser
realizadas por niños sin vigilancia.
ATENCIÓN: Dejar un quemador con
grasas o aceites sin vigilancia puede
ser peligroso y provocar un incendio.
NUNCA intente apagar una llama/in-
cendio con agua, se debe apagar el
aparato y cubrir la llama, por ejemplo,
con una tapa o con una manta ignífu-
ga.
No utilice productos abrasivos ni
espátulas de metal cortantes para
limpiar la puerta de cristal del horno ya
que podrían rayar la superficie y qu-
ebrar el cristal.
Las superficies internas del cajón (cu-
ando existe) pueden calentarse.
No utilice nunca limpiadores a vapor
o de alta presión para la limpieza del
aparato.
Elimine eventuales líquidos presentes
sobre la tapa antes de abrirla. No cierre
la tapa de vidrio (si existe) cuando los
quemadores o la placa eléctrica todavía
están calientes.
ATENCIÓN: Antes de sustituir la lámpa-
ra controle que el aparato esté apagado
para evitar la posibilidad de choques
eléctricos.
ATENCIÓN: el uso de protecciones ina-
propiadas de la placa de cocción puede
provocar accidentes.
ATENCIÓNATENCIÓNATENCIÓN
! Cuando introduzca la parrilla, con-
trole que el tope esté dirigido hacia
arriba y en la parte posterior de la
cavidad.
6
1 Hob burner
2 Hob Grid
3.Control panel
4.Sliding grill rack
5.DRIPPING pan
6.Adjustable foot
7.Containment surface for spills
8.GUIDE RAILS for the sliding racks
9.position 5
10.position 4
11.position 3
12.position 2
13.position 1
Description of the appliance
Overall view
GB
1. Quemador de gas
2.Plano de contención eventuales derrames
3. Panel de mandos
4. Rejilla estante del horno
5. Asadera o plano de cocción
6. Patitas regulables
7. Rejilla del plano de cocción
8. GUÍAS de deslizamiento de las bandejas
9.
POSICIÓN
5
10.
POSICIÓN
4
11.
POSICIÓN 3
12.
POSICIÓN
2
13.
POSICIÓN
1
Descripción del aparato
Vista de conjunto
ES
1. Queimador a gás
2. Grade do piano de trabalho
3. Painel de comandos
4. Prateleira GRADE
5. Prateleira BANDEJA PINGADEIRA
6. Pé de regulação
7. Plano de retenção dos eventuais vazamentos
8. GUIAS de deslizamento das prateleiras
9. Posição 5
10. Posição 4
11.Posição 3
12. Posição 2
13. Posição 1
Descrição do aparelho
Vista de conjunto
PT
1
2
4
5
6
7
9
10
11
12
13
8
3
6
1.Brûleur à gaz
2.Grille du plan de cuisson
3.Tableau de bord
4. Support GRILLE
5. Support LECHEFRITE
6.Pied de réglage
7.Plateau du plan de cuisson
8. GLISSIERES de coulissement
9. niveau 5
10.niveau 4
11.niveau 3
12.niveau 2
13.niveau 1
Description de l’appareil
Vue d’ensemble
FR
7
1
2
3
4
6
Description of the appliance
Control panel
GB
1.THERMOSTAT knob
2.SELECTOR knob
3.THERMOSTAT Indicator light
4.Hob BURNER control knob
6.TIMER knob
Description de l’appareil
Tableau de bord
FR
Descrição do aparelho
Painel de comandos
PT
1.Selector para a temperatura de cozedura (termostato)
3.Indicador de funcionamento termostato
2.Botão selector das funções de cozedura
4.Botão luz do forno e rotisserie
6.Botão contador de minutos.
1.Manette du THERMOSTAT
3.Voyant lumineux THERMOSTAT
2.Manette PROGRAMMES
4.Manette BRULEURS
6.Minuteur
Descripción del aparato
Panel de control
ES
2.Perilla PROGRAMAS
3.La luz piloto del termóstato
4.Perillas de mando de los quemadores
1.Perilla TERMOSTATO
6. Perilla TIMER
5
5.OVEN Indicator light
5.Voyant lumineux FOUR
5.La luz piloto del horno
5.Indicador de funcionamento horno
8
GB
! Before operating your new appliance please read
this instruction booklet carefully. It contains important
information concerning the safe installation and operation
of the appliance.
! Please keep these operating instructions for future
reference. Make sure that the instructions are kept with
the appliance if it is sold, given away or moved.
! The appliance must be installed by a qualified
professional according to the instructions provided.
! Any necessary adjustment or maintenance must be
performed after the cooker has been disconnected from
the electricity supply.
Room ventilation
The appliance may only be installed in permanently-
ventilated rooms, in accordance with current national
legislation. The room in which the appliance is installed
must be ventilated adequately so as to provide as much
air as is needed by the normal gas combustion process
(the flow of air must not be lower than 2 m
3
/h per kW of
installed power).
The air inlets, protected by grilles, should have a duct
with an inner cross section of at least 100 cm
2
and should
be positioned so that they are not liable to even partial
obstruction (see  gure A).
These inlets should be enlarged by 100% - with a
minimum of 200 cm
2
- whenever the surface of the hob
is not equipped with a flame failure safety device. When
the flow of air is provided in an indirect manner from
adjacent rooms (see  gure B), provided that these are
not communal parts of a building, areas with increased
fire hazards or bedrooms, the inlets should be fitted with
a ventilation duct leading outside as described above.
Adjacent room Room requiring ventilation
A B
Ventilation opening Increase in the gap
between
for comburent air the door and the
flooring
Disposing of combustion fumes
The disposal of combustion fumes should be guaranteed
using a hood connected to a safe and efficient natural
suction chimney, or using an electric fan that begins
to operate automatically every time the appliance is
switched on (see  gure).
Fumes channelled Fumes channelled through
Installation
A
! After prolonged use of the appliance, it is advisable to
open a window or increase the speed of any fans used.
straight outside a chimney or a branched
flue system (reserved for
cooking appliances)
! The liquefied petroleum gases are heavier than air and
collect by the floor, therefore all rooms containing LPG
cylinders must have openings leading outside so that
any leaked gas can escape easily.
LPG cylinders, therefore, whether partially or completely
full, must not be installed or stored in rooms or storage
areas that are below ground level (cellars, etc.). Only
the cylinder being used should be stored in the room;
this should also be kept well away from sources of
heat (ovens, chimneys, stoves) that may cause the
temperature of the cylinder to rise above 50°C.
Positioning and levelling
! It is possible to install the appliance alongside
cupboards whose height does not exceed that of the
hob surface.
! Make sure that the wall in contact with the back of the
appliance is made from a non-flammable, heat-resistant
material (T 90°C).
To install the appliance correctly:
• Place it in the kitchen, the dining room or the bed-sit
(not in the bathroom).
If the top of the hob is higher than the cupboards, the
appliance must be installed at least 600 mm away from
them.
If the cooker is installed underneath a wall cabinet,
there must be a minimum distance of 420 mm between
this cabinet and the top of the hob.
This distance should be increased to 700 mm if the wall
cabinets are flammable (see  gure).
9
GB
Do not position blinds
behind the cooker or less
than 200 mm away from
its sides.
Any hoods must be
installed according to
the instructions listed in
the relevant operating
manual.
Levelling
If it is necessary to level the
appliance, screw the adjustable
feet into the places provided on
each corner of the base of the
cooker (see  gure).
The legs* fit into the slots on the
underside of the base of the
cooker.
Electrical connection
Install a standardised plug corresponding to the load
indicated on the appliance data plate (see Technical data
table).
The appliance must be directly connected to the mains using
an omnipolar circuit-breaker with a minimum contact opening
of 3 mm installed between the appliance and the mains. The
circuit-breaker must be suitable for the charge indicated and
must comply with current electrical regulations (the earthing
wire must not be interrupted by the circuit-breaker). The
supply cable must be positioned so that it does not come
into contact with temperatures higher than 50°C at any point.
Before connecting the appliance to the power supply,
make sure that:
The appliance is earthed and the plug is compliant with
the law.
The socket can withstand the maximum power of the
appliance, which is indicated by the data plate.
The voltage is in the range between the values
indicated on the data plate.
The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask
an authorised technician to replace it. Do not use
extension cords or multiple sockets.
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min. mm.
420
Min. mm.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only.
! The manufacturer declines any liability should these
safety measures not be observed.
Gas connection
Connection to the gas network or to the gas cylinder
may be carried out using a flexible rubber or steel hose,
in accordance with current national legislation and after
making sure that the appliance is suited to the type of gas
with which it will be supplied (see the rating sticker on
the cover: if this is not the case see below). When using
liquid gas from a cylinder, install a pressure regulator
which complies with current national regulations. To
make connection easier, the gas supply may be turned
sideways*: reverse the position of the hose holder with
that of the cap and replace the gasket that is supplied
with the appliance.
! Check that the pressure of the gas supply is consistent
with the values indicated in the Table of burner and
nozzle specifications (see below). This will ensure the
safe operation and durability of your appliance while
maintaining efficient energy consumption.
Gas connection using a flexible rubber hose
Make sure that the hose complies with current national
legislation. The internal diameter of the hose must
measure: 8 mm for liquid gas supply; 13 mm for methane
gas supply.
Once the connection has been performed, make sure
that the hose:
Does not come into contact with any parts that reach
temperatures of over 50°C.
Is not subject to any pulling or twisting forces and that
it is not kinked or bent.
Does not come into contact with blades, sharp corners
or moving parts and that it is not compressed.
Is easy to inspect along its whole length so that its
condition may be checked.
Is shorter than 1500 mm.
Fits firmly into place at both ends, where it will be fixed
using clamps that comply with current regulations.
10
GB
! If one or more of these conditions is not fulfilled or if
the cooker must be installed according to the conditions
listed for class 2 - subclass 1 appliances (installed
between two cupboards), the flexible steel hose must
be used instead (see below).
Connecting a flexible jointless stainless steel pipe to
a threaded attachment
Make sure that the hose and gaskets comply with current
national legislation.
To begin using the hose, remove the hose holder on the
appliance (the gas supply inlet on the appliance is a
cylindrical threaded 1/2 gas male attachment).
! Perform the connection in such a way that the hose
length does not exceed a maximum of 2 metres, making
sure that the hose is not compressed and does not come
into contact with moving parts.
Checking the tightness of the connection
When the installation process is complete, check the hose
fittings for leaks using a soapy solution. Never use a flame.
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas other
than the default type (this is indicated on the rating label
on the cover).
3. While the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa
several times, checking that the flame is not extinguished.
! The hob burners do not require primary air adjustment.
! After adjusting the appliance so it may be used with a
different type of gas, replace the old rating label with a
new one that corresponds to the new type of gas (these
labels are available from Authorised Technical Assistance
Centres).
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet hose in
accordance with current national regulations relating
Adapting the hob
Replacing the nozzles for the hob burners:
1. Remove the hob grids and slide the burners off their
seats.
2. Unscrew the nozzles using a 7 mm socket spanner
(see  gure), and replace them with nozzles suited to the
new type of gas (see Burner and nozzle speci cations table).
3. Replace all the components by following the above
instructions in reverse.
Adjusting the hob burners’ minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust
the regulatory screw, which is
positioned inside or next to the
tap pin, until the flame is small
but steady.
! If the appliance is connected to
a liquid gas supply, the regulatory
screw must be fastened as tightly
as possible:
Replacing the Triple ring burner nozzles
1. Remove the pan supports and lift the burners out of
their housing. The burner consists of two separate
parts (see pictures).
2. Unscrew the nozzles using a 7 mm socket spanner.
Replace the nozzles with models that are configured
for use with the new type of gas (see Table 1). The two
nozzles have the same hole diameter.
3. Replace all the components by completing the above
operations in reverse order.
Adjusting the burners’ primary air :
Does not require adjusting.
Setting the burners to minimum:
1. Turn the tap to the low flame position.
2. Remove the knob and adjust the adjustment screw,
which is positioned in or next to the tap pin, until the
flame is small but steady.
3. Having adjusted the flame to the required low setting,
while the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa
several times, checking that the flame does not go out
4. Some appliances have a safety device (thermocouple)
fitted. If the device fails to work when the burners are
set to the low flame setting, increase this low flame
setting using the adjusting screw.
11
GB
Table of burner and nozzle specifications
Safety Chain
! In order to prevent accidental tipping of the appliance,
for example by a child climbing onto the oven door, the
supplied safety chain MUST be installed!
The cooker is fitted with a safety chain to be fixed by
means of a screw (not supplied with the cooker) to the
wall behind the appliance, at the same height as the chain
is attached to the appliance.
Choose the screw and the screw anchor according to
the type of material of the wall behind the appliance. If
the head of the screw has a diameter smaller than 9mm,
a washer should be used. Concrete wall requires the
screw of at least 8mm of diameter, and 60mm of length.
Ensure that the chain is fixed to the rear wall of the cooker
and to the wall, as shown in figure, so that after installation
it is tensioned and parallel to the ground level.
S
R
TC A
5. Once the adjustment has been made, replace the seals
on the by-passes using sealing wax
! If the appliance is connected to liquid gas, the regulation
screw must be fastened as tightly as possible.
! Once this procedure is finished, replace the old rating
sticker with one indicating the new type of gas used.
Stickers are available from any of our Service Centres.
! Should the gas pressure used be different (or vary
slightly) from the recommended pressure, a suitable
pressure regulator must be fitted to the inlet pipe (in order
to comply with current national regulations).
87
69
50
128
104
78
51
Tripple Ring (TC)
236 232 2x99 309
130
3.25 1.50 2x65
63
58
A6TMH2AF EXA6TMH2AF EXA6TMH2AF EX
12
GB
Start-up and use
Using the hob
Lighting the burners
For each BURNER knob there is a complete ring showing
the strength of the flame for the relevant burner.
To light one of the burners on the hob:
1. Bring a flame or gas lighter close to the burner.
2. Press the BURNER knob and turn it in an anticlockwise
direction so that it is pointing to the maximum flame
setting .
3. Adjust the intensity of the flame to the desired level by
turning the BURNER knob in an anticlockwise direction. This
may be the minimum setting , the maximum setting or
any position in between the two.
If the appliance is fitted with an
electronic lighting device* (see
gure), press the ignition button,
marked with the symbol
, then
hold the BURNER knob down
and turn it in an anticlockwise
direction, towards the maximum
flame setting, until the burner
is lit.The burner may be extinguished when the knob is
released. If this occurs, repeat the operation, holding the
knob down for a longer period of time.
! If the flame is accidentally extinguished, switch off the
burner and wait for at least 1 minute before attempting
to relight it.
If the appliance is equipped with a flame failure
safety device*, press and hold the BURNER knob for
approximately 2-3 seconds to keep the flame alight and
to activate the device.
To switch the burner off, turn the knob until it reaches
the stop position •.
Flame adjustment according to levels
the burner flame intensity can be adjusted with the
knob according to 6 power levels, from maximum
to minimum with 4 intermediate positions:
a click will indicate the change from one level to
another when turning the knob. The system
guarantees a more precise adjustment, allows
to replicate the flame intensity and to identify
easily the preferred level for different cooking
operations.
*
Only available in certain models.
Practical advice on using the burners
For the burners to work in the most efficient way possible
and to save on the amount of gas consumed, it is
recommended that only pans that have a lid and a flat
base are used. They should also be suited to the size of
the burner:
To identify the type of burner, please refer to the diagrams
contained in the “Burner and nozzle specifications”.
! For models equipped with a reducer grid, the latter must
be used only for the auxiliary burner, when pans with a
diameter of less than 12 cm are used.
Using the oven
! The first time you use your appliance, heat the empty
oven with its door closed at its maximum temperature
for at least half an hour. Ensure that the room is well
ventilated before switching the oven off and opening the
oven door. The appliance may emit a slightly unpleasant
odour caused by protective substances used during the
manufacturing process burning away.
! Before operating the product, remove all plastic film
from the sides of the appliance.
! Never put objects directly on the bottom of the oven; this
will avoid the enamel coating being damaged.
1. Select the desired cooking mode by turning the
SELECTOR knob.
2. Select the recommended temperature for the
cooking mode or the desired temperature by turning the
THERMOSTAT knob.
A list detailing cooking modes and suggested cooking
temperatures can be found in the relevant table (see Oven
cooking advice table).
During cooking it is always possible to:
Change the cooking mode by turning the SELECTOR
knob.
Change the temperature by turning the THERMOSTAT
knob.
Burner Cookware Diameter (cm)
Fast (R) 24 - 26
Semi Fast (S) 16 - 20
Auxiliary (A) 10 - 14
Triple Crown (TC) 24 - 26
13
GB
Stop cooking by turning the SELECTOR knob to the
“0” position.
! Always place cookware on the rack(s) provided.
THERMOSTAT indicator light
When this is illuminated, the oven is generating heat.
It switches off when the inside of the oven reaches the
selected temperature. At this point the light illuminates
and switches off alternately, indicating that the thermostat
is working and is maintaining the temperature at a
constant level.
Oven light
This is switched on by turning the SELECTOR knob to
any position other than “0”. It remains lit as long as the
oven is operating. By selecting
with the knob, the
light is switched on without any of the heating elements
being activated.
Cooking modes
! A temperature value can be set for all cooking modes
between 60°C and Max, except for the following modes
GRILL (recommended: set only to MAX power level)
GRATIN (recommended: do not exceed 200°C).

TRADITIONAL OVEN mode
Both the top and bottom heating elements will come on.
When using this traditional cooking mode, it is best to use
one cooking rack only. If more than one rack is used, the
heat will be distributed in an uneven manner.
BAKING mode
The rear heating element and the fan are switched on,
thus guaranteeing the distribution of heat in a delicate and
uniform manner throughout the entire oven. This mode is
ideal for baking and cooking temperature sensitive foods
(such as cakes that need to rise) and for the preparation
of pastries on 3 shelves simultaneously.
FAST COOKING mode
The heating elements and the fan come on, guaranteeing
the distribution of heat consistently and uniformly
throughout the oven.
Preheating is not necessary for this cooking mode. This
mode is particularly suitable for cooking pre-packed
food quickly (frozen or pre-cooked). The best results are
achieved using one cooking rack only.
MULTI-COOKING mode
All the heating elements (top, bottom and circular) switch
on and the fan begins to operate. Since the heat remains
constant throughout the oven, the air cooks and browns
food in a uniform manner. A maximum of two racks may
be used at the same time.
PIZZA mode
The circular heating elements and the elements at
the bottom of the oven are switched on and the fan is
activated. This combination heats the oven rapidly by
producing a considerable amount of heat, particularly
from the element at the bottom. If you use more than one
rack at a time, switch the position of the dishes halfway
through the cooking process.
GRILL mode
The central part of the top heating element is switched
on. The high and direct temperature of the grill is
recommended for food that requires a high surface
temperature (veal and beef steaks, fillet steak and
entrecôte). This cooking mode uses a limited amount of
energy and is ideal for grilling small dishes. Place the food
in the centre of the rack, as it will not be cooked properly
if it is placed in the corners.
GRATIN
mode
The top heating element and the rotisserie (where
present) are activated and the fan begins to operate.
This combination of features increases the effectiveness
of the unidirectional thermal radiation provided by the
heating elements through forced circulation of the air
throughout the oven. This helps prevent food from burning
on the surface and allows the heat to penetrate right into
the food.
! The GRILL and GRATIN cooking modes must be
performed with the oven door shut.
DEFROSTING mode
The fan located on the bottom of the oven makes the air
circulate at room temperature around the food. This is
recommended for the defrosting of all types of food, but in
particular for delicate types of food which do not require
heat, such as for example: ice cream cakes, cream or
custard desserts, fruit cakes. By using the fan, the
defrosting time is approximately halved. In the case of
meat, fish and bread, it is possible to accelerate the
process using the “multi-cooking” mode and setting the
temperature to 80° - 100°C.

14
GB
BOTTOM VENTILATED mode
The bottom heating element and the fan is activated,
which allows for the heat distribution within the whole
cavity of the oven. This combination is useful for light
cooking of vegetables and fish.
BOTTOM mode :
The lower heating element is activated. This position
is recommended for perfecting the cooking of dishes
(in baking trays) which are already cooked on the
surface but require further cooking in the centre, or
for desserts with a covering of fruit or jam, which only
require moderate colouring on the surface. It should
be noted that this function does not allow the maximum
temperature to be reached inside the oven (250°C)
and it is therefore not recommended that foods are
cooked using only this setting, unless you are baking
cakes (which should be baked at a temperature of
180°C or lower).
Practical cooking advice
! In the GRILL cooking mode, place the dripping pan in
position 1 to collect cooking residues (fat and/or grease).
GRILL
Insert the rack in position 3 or 4. Place the food in the
centre of the rack.
We recommend that the power level is set to maximum.
The top heating element is regulated by a thermostat
and may not always operate constantly.
PIZZA
• Use a light aluminium pizza pan. Place it on the rack
provided.
For a crispy crust, do not use the dripping pan as it
prevents the crust from forming by extending the total
cooking time.
If the pizza has a lot of toppings, we recommend
adding the mozzarella cheese on top of the pizza
halfway through the cooking process.
WARNING! The oven is provided with
a stop system to extract the racks and
prevent them from coming out of the
oven.(1)
As shown in the drawing, to extract
them completely, simply lift the racks,
holding them on the front part, and
pull (2).
Cooking Control Timer Knob
Some models are equipped with a timer program to
control when the oven shuts off during cooking. To use
this feature, you must wind the knob one full turn in the
counter-clockwise direction ; Then, turn the knob in
the clockwise direction
, to set the time by matching
up the indicator on the control panel with the number
of minutes on the knob.
At the end of the programmed length of time, the timer
will sound and automatically turn off the oven.
Attention: to use the oven in manual mode without the
cooking control timer, match the indicator on the
control panel with the
symbol on the timer knob.
When the oven is not in use, the cooking control timer
can be used like a normal timer.
15
GB
Oven cooking advice table
Cooking
modes
Foods Weight
(in kg)
Rack Position Pre-heating
time
(minutes)
Recommended
temperature
Cooking
time
(minutes)
Traditional
Oven
Duck
Roast veal or beef
Pork roast
Biscuits (short pastry)
Tarts
1
1
1
-
1
3
3
3
3
3
15
15
15
15
15
200
200
200
180
180
65-75
70-75
70-80
15-20
30-35
Baking
Mode
Tarts
Fruit cakes
Plum cake
Sponge cake
Stuffed pancakes (on 2 racks)
Small cakes (on 2 racks)
Cheese puffs (on 2 racks)
Cream puffs (on 3 racks)
Biscuits (on 3 racks)
Meringues (on 3 racks)
0.5
1
0.7
0.5
1.2
0.6
0.4
0.7
0.7
0.5
3
2 or 3
3
3
2 and 4
2 and 4
2 and 4
1 and 3 and 5
1 and 3 and 5
1 and 3 and 5
15
15
15
15
15
15
15
15
15
15
180
180
180
160
200
190
210
180
180
90
20-30
40-45
40-50
25-30
30-35
20-25
15-20
20-25
20-25
180
Frozen food
Pizza
Courgette and prawn pie
Country style spinach pie
Turnovers
Lasagne
Golden Rolls
Chicken morsels
0.3
0.4
0.5
0.3
0.5
0.4
0.4
2
2
2
2
2
2
2
-
-
-
-
-
-
-
250
200
220
200
200
180
220
12
20
30-35
25
35
25-30
15-20
Pre-cooked food
Golden chicken wings
0.4
2
-
200
20-25
Fast
cooking
Fresh Food
Biscuits (short pastry)
Plum cake
Cheese puffs
0.3
0.6
0.2
2
2
2
-
-
-
200
180
210
15-18
45
10-12
Multi-
cooking
Pizza (on 2 racks)
Lasagne
Lamb
Roast chicken + potatoes
Mackerel
Plum cake
Cream puffs (on 2 racks)
Biscuits (on 2 racks)
Sponge cake (on 1 rack)
Sponge cake (on 2 racks)
Savoury pies
1
1
1
1+1
1
1
0.5
0.5
0.5
1
1.5
2 and 4
3
2
2 and 4
2
2
2 and 4
2 and 4
2
2 and 4
3
15
10
10
15
10
10
10
10
10
10
15
230
180
180
200
180
170
190
180
170
170
200
15-20
30-35
40-45
60-70
30-35
40-50
20-25
10-15
15-20
20-25
25-30
Pizza Mode
Pizza
Roast veal or beef
Chicken
0.5
1
1
3
2
2 or 3
15
10
10
220
220
180
15-20
25-30
60-70
Soles and cuttlefish
Squid and prawn kebabs
Cuttlefish
Cod filet
Grilled vegetables
Veal steak
Sausages
Hamburgers
Mackerels
Toasted sandwiches (or toast)
0.7
0.6
0.6
0.8
0.4
0.8
0.6
0.6
1
4 and 6
4
4
4
4
3 or 4
4
4
4
4
4
-
-
-
-
-
-
-
-
-
-
Max
Max
Max
Max
Max
Max
Max
Max
Max
Max
10-12
8-10
10-15
10-15
15-20
15-20
15-20
10-12
15-20
3-5
Gratin
Grilled chicken
Cuttlefish
1.5
1.5
2
2
10
10
200
200
55-60
30-35
Bottom
Ventilated
Bottom
For perfecting cooking
Bottom
Ventilated
Bottom
Grill
16
GB
Precautions and tips
! This appliance has been designed and manufactured
in compliance with international safety standards.
The following warnings are provided for safety reasons
and must be read carefully.
General safety
The appliance was designed for domestic use inside
the home and is not intended for commercial or
industrial use.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
Do not touch the appliance with bare feet or with wet
or damp hands and feet.
The appliance must be used by adults only for
the preparation of food, in accordance with the
instructions outlined in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous.
The manufacturer may not be held liable for any
damage resulting from improper, incorrect and
unreasonable use of the appliance.
The instruction booklet accompanies a class 1
(insulated) or class 2 - subclass 1 (recessed between
2 cupboards) appliance.
Do not touch the heating elements or certain parts
of the oven door when the appliance is in use;
these parts become extremely hot. Keep children
well away from the appliance.
Make sure that the power supply cables of other
electrical appliances do not come into contact with
the hot parts of the oven.
• The openings used for the ventilation and dispersion
of heat must never be covered.
Always use oven gloves when placing cookware in the
oven or when removing it.
Do not use flammable liquids (alcohol, petrol, etc...)
near the appliance while it is in use.
Do not place flammable material in the lower storage
compartment or in the oven itself. if the appliance is
switched on accidentally, they could catch fire.
The internal surfaces of the compartment (where
present) may become hot.
Always make sure the knobs are in the
position when
the appliance is not in use.
When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
Never perform any cleaning or maintenance work
without having disconnected the appliance from the
electricity mains.
If the appliance breaks down, under no circumstances
should you attempt to perform the repairs yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
Contact Assistance.
Do not rest heavy objects on the open oven door.
The appliance should not be operated by people
(including children) with reduced physical, sensory
or mental capacities, by inexperienced individuals or
by anyone who is not familiar with the product. These
individuals should, at the very least, be supervised
by someone who assumes responsibility for their
safety or receive preliminary instructions relating to
the operation of the appliance.
Do not let children play with the appliance.
•If the cooker is placed on a pedestal, take the necessary
precautions to prevent the cooker from sliding off the
pedestal itself.
Disposal
When disposing of packaging material: observe local
legislation so that the packaging may be reused.
The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the materials
inside the machine, while preventing potential damage
to the atmosphere and to public health. The crossed-
out dustbin is marked on all products to remind the
owner of their obligations regarding separated waste
collection.
For further information relating to the correct disposal of
exhausted household appliances, owners may contact
the public service provided or their local dealer.
Respecting and conserving the
environment
You can help to reduce the peak load of the electricity
supply network companies by using the oven in the
hours between late afternoon and the early hours of
the morning.
Always keep the oven door closed when using the
GRILL and DOUBLE GRILL modes. This will achieve
better results while saving energy (approximately
10%).
• Check the door seals regularly and wipe them clean
to ensure they are free of debris so that they adhere
properly to the door, thus avoiding heat dispersion.
17
GB
Switching the appliance off
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Cleaning the appliance
! Never use steam cleaners or pressure cleaners on the
appliance.
The stainless steel or enamel-coated external parts and
the rubber seals may be cleaned using a sponge that
has been soaked in lukewarm water and neutral soap.
Use specialised products for the removal of stubborn
stains. After cleaning, rinse well and dry thoroughly.
Do not use abrasive powders or corrosive substances.
The hob grids, burner caps, flame spreader rings and
burners may be removed to make cleaning easier;
wash them in hot water and non-abrasive detergent,
making sure all burnt-on residue is removed before
drying them thoroughly.
Clean the terminal part of the flame failure safety
devices* frequently.
The inside of the oven should ideally be cleaned after
each use, while it is still lukewarm. Use hot water and
detergent, then rinse well and dry with a soft cloth. Do
not use abrasive products.
Clean the glass part of the oven door using a sponge
and a non-abrasive cleaning product, then dry
thoroughly with a soft cloth. Do not use rough abrasive
material or sharp metal scrapers as these could
scratch the surface and cause the glass to crack.
The accessories can be washed like everyday
crockery, and are even dishwasher safe.
Do not close the cover when the burners are alight or
when they are still hot.
Inspecting the oven seals
Check the door seals around the oven regularly. If
the seals are damaged, please contact your nearest
Authorised After-sales Service Centre. We recommend
that the oven is not used until the seals have been
replaced.
Replacing the oven light bulb
1. After disconnecting the oven
from the electricity mains, remove
the glass lid covering the lamp
socket (see  gure).
2. Remove the light bulb and
replace it with a similar one:
voltage 230 V, wattage 25 W,
cap E 14.
3. Replace the lid and reconnect
the oven to the electricity supply.
! Do not use the oven lamp as/for ambient lighting.
Gas tap maintenance
Over time, the taps may become jammed or difficult to
turn. If this occurs, the tap must be replaced.
! This procedure must be performed by a qualified
technician authorised by the manufacturer.
Assistance
! Never use the services of an unauthorised technician.
Please have the following information to hand:
The type of problem encountered.
The appliance model (Mod.).
The serial number (S/N).
The latter two pieces of information can be found on the
data plate located on the appliance.
Care and maintenance
Removing and fitting the oven door:
1.Open the door
2.Make the hinge clamps of the oven door rotate
backwards completely (see photo)
3.Close the door until the clamps stop (the door will
remain open for 40° approx.) (see photo)
18
GB
40°
4.Press the two buttons on the upper profile and
extract the profile (see photo)
5.Remove the glass sheet and do the cleaning as
indicated in chapter: "Care and maintenance".
6.Replace the glass.
WARNING! Oven must not be operated with inner
door glass removed!
WARNING! When reassembling the inner door
glass insert the glass panel correctly so that the
text written on the panel is not reversed and
can be easily legible.
7.Replace the profile, a click will indicate that the
part is positioned correctly.
8.Open the door completely.
9.Close the supports (see photo).
10.Now the door can be completely closed and the
oven can be started for normal use.
Steam-Assisted Oven Cleaning
This method of cleaning is recommended especially after
cooking very fatty (roasted)meats.
This cleaning process allows to facilitate the removal of
dirt of the walls of the oven by the generation of steam
that is created inside the oven cavity for easier cleaning.
! Important! Before you start steam -cleaning:
-Remove any food residue and grease from the bottom
of the oven.
- Remove any oven accessories (grids and drip pans).
Perform the above operations according to the following
procedure:
1. pour 300ml of water into the baking tray in the oven,
placing it in the bottom shelf. In the models where the
drip pan is not present, use a baking sheet and place it
on the grill at the bottom shelf;
2. select the function of the oven
and set the temperature to 100 ° C;
3. keep it in the oven for 15min;
4. turn off the oven;
5. Once cooled the oven, you can open the door to
complete the cleaning with water and a damp cloth;
6. eliminate any residual water from the cavity after
finishing cleaning
When the steam –cleaning is done, after cooking
especially fatty foods, or when grease is difficult to
remove, you may need to complete the cleaning with the
traditional method, described in the previous paragraph.
! Perform cleaning only in the cold oven!
BOTTOM
19
FR
! Conservez ce mode d’emploi pour pouvoir le consulter
à tout moment. En cas de vente, de cession ou de
déménagement, veillez à ce qu’il suive l’appareil.
! Lisez attentivement les instructions : elles contiennent
des conseils importants sur l’installation, l’utilisation et la
sécurité de votre appareil.
! L’installation de l’appareil doit être effectuée par un
professionnel du secteur conformément aux instructions
du fabricant.
! N’importe quelle opération de réglage, d’entretien, etc.,
doit être effectuée après avoir débranché la prise de la
cuisinière.
Aération des locaux
L’appareil doit être installé dans des locaux qui sont
aérés en permanence, selon les prescriptions des
Normes en vigueur dans le pays d’installation. Il est
indispensable que la pièce où l’appareil est installé
dispose d’une quantité d’air égale à la quantité d’air
comburant nécessaire à une bonne combustion du
gaz (le flux d’air doit être d’au moins 3 m
3
/h par kW de
puissance installée).
Les prises d’air, protégées par des grilles, doivent
disposer d’un conduit d’au moins 2 cm2 de section
utile et dans une position qui leur évite tout risque d’être
bouchées accidentellement, même partiellement (voir
figure A).
Ces ouvertures doivent être agrandies de 100% (surface
minimale 2 cm2) en cas d’appareils dépourvus du
dispositif de sécurité de flamme et quand l’afflux de l’air
provient de manière indirecte de pièces voisines (voir
figure B) – à condition qu’il ne s’agisse pas de parties
communes du bâtiment, de chambres à coucher ou
de locaux à risque d’incendie – équipées d’un conduit
d’aération avec l’extérieur comme décrit plus haut.
Local adjacent Local à ventiler
A
Ouverture de ventilation Agrandissement de la fissure
pour l’air comburant entre la porte et le sol
Fig. A Fig. B
! Après une utilisation prolongée de l’appareil, il est
conseillé d’ouvrir une fenêtre ou d’augmenter la vitesse
de ventilateurs éventuels.
Evacuation des fumées de combustion
La pièce doit prévoir un système d’évacuation vers
l’extérieur des fumées de combustion réalisé au moyen
d’une hotte reliée à une cheminée à tirage naturel ou
par ventilateur électrique qui entre automatiquement en
fonction dès qu’on allume l’appareil (voir figures).
Evacuation directement Evacuation par cheminée ou conduit
à l’extérieur de fumée ramifié (réservé
aux
appareils de cuisson)
! Les gaz de pétrole liquéfiés, plus lourds que l’air,
se déposent et stagnent dans le bas. Les locaux qui
contiennent des bouteilles de G.P.L doivent donc prévoir
des ouvertures vers l’extérieur afin de permettre l’évacuation
du gaz par le bas en cas de fuites accidentelles. Ne pas
installer ou entreposer de bouteilles de GPL, vides ou
partiellement pleines, dans des locaux qui se trouvent
en sous-sol (caves etc.). Ne gardez dans la pièce que la
bouteille que vous êtes en train d’utiliser, loin de sources
de chaleur (fours, feux de bois, poêles etc.) qui pourraient
amener sa température à plus de 50°C.
Positionnement et nivellement
! L’appareil peut être installé à côté de meubles dont la
hauteur ne dépasse pas celle du plan de cuisson.
! Assurez-vous que le mur en contact avec la paroi arrière
de l’appareil est réalisée en matériel ignifuge résistant à
la chaleur (T 90°C).
Pour une installation correcte :
installez cet appareil dans une cuisine, une salle à
manger ou un studio (jamais dans une salle de bains);
si le plan de cuisson de la cuisinière dépasse le plan de
travail des meubles, ces derniers doivent être placés
à au moins 600 mm de l’appareil;
• si la cuisinière est installée sous un élément suspendu,
il faut que ce dernier soit placé à au moins 420mm de
distance du plan. Il faut prévoir une distance de 700mm
Installation
FR
20
si les éléments suspendus
sont inflammables (voir
gure);
ne placez pas
de rideaux derrière la
cuisinière ou sur ses
côtés à moins de 200
mm de distance;
pour l’installation de
hottes, conformez-vous
aux instructions de leur notice d’emploi.
Nivellement
Pour mettre l’appareil bien à
plat, vissez les pieds de réglage
fournis aux emplacements
prévus aux coins à la base de la
cuisinière (voir figure).
Montage des pieds* par
encastrement sous la base.
Raccordement électrique
Montez sur le câble une prise normalisée pour la charge
indiquée sur l’étiquette des caractéristiques (voir tableau
des caractéristiques techniques).
En cas de raccordement direct au réseau, il faut intercaler
entre l’appareil et le réseau un interrupteur à coupure
omnipolaire ayant au moins 3 mm d’écartement entre
les contacts, dimensionné à la charge et conforme
aux normes NFC 15-100 (le fil de terre ne doit pas être
interrompu par l’interrupteur). Le câble d’alimentation
ne doit atteindre, en aucun point, des températures
dépassant de 50°C la température ambiante.
Avant de procéder au branchement, assurez-vous que :
la prise est bien munie d’une terre conforme à la loi;
la prise est bien apte à supporter la puissance
maximale de l’appareil, indiquée sur la plaquette
signalétique;
la tension d’alimentation est bien comprise entre les
valeurs indiquées sur la plaquette signalétique;
la prise est bien compatible avec la fiche de l’appareil.
Si ce n’est pas le cas, remplacez la prise ou la fiche,
n’utilisez ni rallonges ni prises multiples.
HOOD
420
Min.
min.
650
mm. with hood
min.
700
mm. without hood
mm.
600
Min. mm.
420
Min. mm.
! Après installation de l’appareil, le câble électrique et
la prise de courant doivent être facilement accessibles
! Le câble ne doit être ni plié ni excessivement écrasé.
! Le câble doit être contrôlé périodiquement et ne peut
être remplacé que par un technicien agréé.
! Nous déclinons toute responsabilité en cas de non
respect des normes énumérées ci-dessus.
Raccordement gaz
Pour raccorder l’appareil au réseau de distribution
du gaz ou à la bouteille de gaz utilisez un tuyau
flexible en caoutchouc ou en acier, conformément à la
réglementation en vigueur. Assurez-vous auparavant
que l’appareil est bien réglé pour le type de gaz
d’alimentation utilisé (voir étiquette sur le couvercle :
autrement voir ci-dessous). Si l’alimentation s’effectue avec
du gaz liquide en bouteille, utilisez des régulateurs de
pression conformes à la réglementation en vigueur dans
le pays. Pour simplifier le raccordement, l’alimentation
du gaz est orientable latéralement* : inversez l’about
annelé avec le bouchon de fermeture et remplacez le
joint d’étanchéité (fourni avec lappareil).
! Pour un fonctionnement en toute sécurité, pour un
meilleur emploi de l’énergie et une plus longue durée de
vie de l’appareil, vérifiez que la pression d’alimentation
respecte bien les valeurs indiquées dans le tableau
Caractéristiques des brûleurs et des injecteurs (voir
ci-dessous).
Raccordement gaz par tuyau flexible en caoutchouc
Assurez-vous que le tuyau est bien conforme aux normes
applicables dans le pays d’installation. Le tuyau doit avoir
un diamètre intérieur de : 8 mm en cas d’alimentation au
gaz liquide; 15 mm en cas d’alimentation au gaz naturel.
Après avoir effectué le raccordement, assurez-vous que
le tuyau :
ne touche en aucun point à des parties pouvant
atteindre plus de 50°C;
ne soit pas soumis à traction ou torsion et ne présente
pas de pliures ou étranglements;
ne risque pas d’entrer en contact avec des corps
tranchants, des arêtes vives, des parties mobiles et
ne soit pas écrasé;
puisse être facilement contrôlable sur toute sa
longueur pour vérifier son état de conservation;
ait moins de 1500mm de long;
soit bien fixé à ses deux extrémités à l’aide de
bagues de serrage conformes à la réglementation
en vigueur dans le pays.
*N’existe que sur certains modèles
1 / 1

Ariston A6TMH2AF (X) EX Mode d'emploi

Catégorie
Fours
Taper
Mode d'emploi