Thermador ZOME30ABS Guide d'installation

9000861715

T18....

T24....

T30....

2

3

INSTALLATION INSTRUCTIONS ............................................................................... 4

INSTRUCTIONS D’INSTALLATION ............................................................................ 36

INSTRUCCIONES DE INSTALACIÓN......................................................................... 70

4

Table of Contents

Safety and warning information ......................... 5

Installation options .............................................. 6

Individual appliance .................................................. 6

Side-by-Side ................................................................ 6

Individual appliances with partition ........................ 6

Individual appliance at the end of the kitchen ..... 6

Installation ............................................................ 7

Installation room.......................................................... 7

Stable installation ...................................................... 7

Installation enclosure ................................................ 7

Furniture ...................................................................... 7

Floor ............................................................................. 7

Aligning the appliance .............................................. 7

Connecting the power ......................................... 8

Connecting the water .......................................... 8

Dimensions of the installation niche ................. 9

Required accessories and tools ......................... 10

Supplied accessories ............................................... 10

Optional accessories ................................................ 10

Other required accessories ..................................... 10

Miscellaneous ............................................................ 10

Tools ............................................................................ 10

Installation instructions ...................................... 11

1. Checking the installation

enclosure .............................................. 11

2. Removing the packaging .................. 11

3. Transport of the appliance ................ 12

4. Installation preparation ...................... 12

5. Special installation .............................. 12

1. Attaching the anti-tip-brackets .......... 13

2. Attaching an alternative

anti-tip-device ....................................... 14

3. Attaching an edge protection ........... 14

4. Attaching the fastening sheets

(lateral) ................................................... 14

1. Pushing the appliance into

the installation enclosure ................... 15

2. Aligning the appliance in

the installation enclosure ................... 16

3. Attaching the appliance to

the installation enclosure ................... 16

1. Attaching the toe kick panel ............. 18

2. Aligning the base panel ..................... 18

3. Switching the appliance ON ............. 19

4. Preparing the door panels ................ 19

5. Loading the appliance door .............. 19

6. Removing the installation

support part .......................................... 19

7. Attaching the adjusting rail

to the door panel ................................ 20

8. Attaching the fixation strips

to the door panel ................................ 20

9. Attaching the door panel ................... 21

10. Attaching the lower bracket .............. 22

11. Attaching the strips ............................. 23

12. Mounting the air seperator ................ 23

13. Adjusting the door spring .................. 24

Special installation .............................................. 25

Changing over the door hinges ............... 25

Removing/changing over

the sealing mat ............................................ 28

Side-by-Side installation ............................. 28

Preparing to connect the water ................ 31

Connecting the water to the appliance ..... 31

Aligning the ice-water dispenser .............. 32

Attaching the cover strips ......................... 33

Adjusting the door opening angle ........... 34

5

, Safety and warning information

These mounting instructions are designed to help you

install your new appliance.

The manufacturer cannot be held liable for mounting

which has been improperly carried out. We recommend

that you allow a qualified specialist to set up and switch

the appliance on for the first time.

Following all information and keeping to the instructions

are preconditions for mounting and switching the

appliance on safely for the first time.

Keep the mounting instructions safe for use later on.

Before setting up and switching the appliance on for the

first time, read the mounting instructions fully and

thoroughly.

, WARNING

These appliances are top-heavy and must be

secured to prevent the possibility of tipping forward.

Anti-tip protection is required.

Keep doors closed until the appliance is completely

installed and secured per installation instructions.

Due to the weight and size of this appliance, and to

reduce the risk of personal injury or damage to the

product – TWO PEOPLE ARE REQUIRED FOR

PROPER INSTALLATION.

This appliance must be properly grounded. See the

section on “Connecting the power”.

Use this appliance only for its intended purpose.

Immediately repair or replace electric service cords

that become frayed or damaged.

Unplug the appliance or switch off the fuse before

cleaning or making repairs.

Repairs should be made by a qualified service

technician.

, CAUTION

Installation of this appliance requires basic

mechanical, carpentry and plumbing skills.

Proper installation is the responsibility of the

installer.

Product failure due to improper installation is not

covered under the Appliance Warranty.

See the Owner's Manual for warranty information.

IMPORTANT

Save these instructions for local inspector's use.

Observe all governing codes and ordinances.

Note to Installer – Be sure to leave these instructions

with the Consumer.

Note to Consumer – Keep these instructions with your

Owner's Manual for future reference.

General

These installation instructions are intended for use by

qualified installers. All connections for water, electrical

power and grounding must comply with local codes and

ordinances and be made by licensed personnel when

required. In the absence of a local code:

 In the U.S.A., in accordance with the National

Electric Code, ANSI/NFPA70 – latest edition/State

and Municipal codes and/or local codes.

 In Canada, in accordance with the Canadian Electric

Code C22.1 – latest edition/Provincial and

Municipal codes and/or local codes.

Definitions

,

WARNING

This indicates that death or serious injuries may

occur as a result of not observing this warning.

, CAUTION

This indicates that minor or moderate injuries or

damage may occur as a result of not observing

this warning.

Note:

This is used to draw the user's attention to something in

particular.

6

Installation options

There are many different installation options.

These are limited only by the design of the kitchen.

See also “Kitchen Design Quick Reference”.

Individual appliance

Side-by-Side

If two appliances are set up next to each other, a sealing

kit for Side-by-Side combination should be used in order

to guarantee a stable connection.

For further information see section “Required

accessories and tools”.

Individual appliances with partition

 When dimensioning the partition for model 4, note

the thickness of the door panels to prevent damage

if the doors are opened at the same time.

 Use the Heater Kit for Side-by-Side Installation if the

gap between the appliances is less

than 6" (160 mm).

See the section on “Required accessories and

tools/Optional accessories”.

 Minimum thickness of the partition

5

/

8

" (16 mm).

Individual appliance at the end of the

kitchen

If one side of the appliance is visible, a side panel must

be used.

The side panel must be connected firmly to the wall, the

floor and overhead cabinet/fixtures before the appliance

is placed in the installation niche.

The dimensions of the side panel are taken from the

opposite installation niche wall. During installation

ensure that the installation niche is square and the

proper size.

7

Installation

, WARNING

Do not install the appliance:

 outdoors,

 in an environment with dripping water,

 in rooms which are less than 32 °F (0 °C).

 A fully-loaded appliance is very heavy.

Refrigerator 24" approx. 890 Ibs/400 kg

Refrigerator 30" approx. 1110 Ibs/500 kg

Freezer 18" approx. 560 Ibs/250 kg*

Freezer 24" approx. 780 Ibs/350 kg*

Freezer 30" approx. 950 Ibs/425 kg*

Wine unit 18" approx. 550 Ibs/245 kg

Wine unit 24" approx. 694 Ibs/310 kg

(* without Water Dispenser)

Installation room

The appliance should be installed in a dry, well ventilated

space.

The location should not be exposed to the direct sunlight

and should not lie next to a source of heat such as a

cooker or a radiator etc. If installation next to a source of

heat cannot be avoided, either a suitable insulating plate

should be used or you should keep to the following

minimum distances:

 1

1

/

4

" (3 cm) to electric or gas cookers,

 11

13

/

16

" (30 cm) to an oil-fired or solid-fuel cooker.

Climatic classes

The climate class can be found on the rating plate.

The climate class indicates within which ambient

temperatures the appliance can be operated.

Stable installation

The appliance is very heavy and has a tendency to tilt

forwards when the appliance door is opened.

The appliance must not be switched on until there

is no possibility of the appliance tilting over.

The safest method of installing the appliance in a stable

position is to use the supplied anti-tilt brackets.

If the installation niche is adequately stable and the

appliance can be attached securely to the upper and

side walls of the niche, it may be possible to dispense

with the anti-tilt brackets. A prerequisite for this is always

a firm connection between the niche and back wall!

In the case of doubt, the help of architect or specialist

builder should be enlisted.

Installation niche

It is important to keep to the stated dimensions of the

installation niche with a view to trouble-free fitting, and

the subsequent appearance of the kitchen furniture

frontage.

Special care should be taken that the niche has right

angles. The side walls should not exhibit areas that stick

out, projections or unevenness.

You should determine the right angles of the installation

niche with appropriate means, e.g. by measuring

diagonally and by using a spirit level.

The side walls and the upper end of the installation niche

must be at least

5

/

8

" (16 mm) thick.

Furniture

The new appliance is screwed down tightly using parts

of the cabinet and the upper cabinet.

Care should therefore be taken, that all upper cabinets

to which something has been fastened are securely

connected to the subsurface or wall by appropriate

means.

The minimum thickness of the base should be

a minimum of 19 mm.

Floor

The subsurface must be level and even in order to

ensure that the appliance is securely installed and works

correctly.

The subsurface must be made from a hard, non-flexible

material.

The floor of the installation space must have the same

height as the rest of the space.

On account of the weight of a fully-laden appliance, it is

necessary to have a bearing subsurface. In the case of

doubt, the help of architect or specialist builder should

be enlisted.

Aligning the appliance

To ensure that the appliance functions correctly, it must

be levelled properly.

If the appliance is not level, water may flow out of the ice

maker, ice cubes may be irregular or the doors may not

close properly.

Climatic class Permitted ambient temperature

SN

50 °F to 90 °F (+10 °C to 32 °C)

N

61 °F to 90 °F (+16 °C to 32 °C)

ST

61 °F to 100 °F (+16 °C to 38 °C)

T

61 °F to 110 °F (+16 °C to 43 °C)

8

Connecting the power

, WARNING

 Avoid the risk of an electric shock!

 Insert into a grounded 3-phase socket.

Never remove grounding phase. Do not use any

adapters. Do not use any extension cables.

 Non-compliance with these instructions may

result in death, fire or an electric shock.

Improper connection of the protective

conductor may result in an electric shock. If you

are in doubt whether the appliance has been

grounded properly, have the appliance tested

by a qualified electrician or service technician.

The socket must be near the appliance and also freely

accessible following installation of the appliance.

The appliance complies with protection class I.

Connect the appliance to 115 V/60 Hz alternating

current via a correctly installed socket with protective

conductor. The socket must be fused with a 10 to 16 A

fuse.

The appliance comes with a UL registered 3-wire power

cord. The appliance requires a 3-pole socket. Please

observe the following table with regard to this:

(*) incl. IceMaker

Check on the rating plate whether the indicated voltage

and current type correspond with the values of your

power supply. The location of the rating plate can be

found in the chapter entitled Customer service.

, WARNING

Never connect the appliance to electronic energy

saver plugs. Our appliances can be used with

mains and sine-controlled inverters. Mains-

controlled inverters are used for photovoltaic

systems which are connected directly to the

national grid. Sine-controlled inverters must be

used for isolated applications (e.g. on ships or in

mountain lodges) which are not connected

directly to the national grid.

Connecting the water

, CAUTION

Only connect the appliance to drinking water!

The water may be connected only by a competent fitter

according to the local regulations of the appropriate

water supply company.

A cold water connection is necessary for operating the

automatic ice maker. The water pressure must be

between 25 and 120 p.s.i. (1,72 and 8,25 bar).

The installation must correspond to the local plumbing

regulations.

A separate shut-off valve should be installed in the cold-

water inflow. The shut-off valve should not be located

behind the appliance. It is recommended that you mount

the shut-off valve directly next to the appliance or at

another place which is easily accessible. When installing

the water connection, pay attention to the permissible

installation area for the water mains.

For connection to the drinking water mains use only

water pipes which are suitable for drinking water.

Observe national regulations and the connection

conditions of the local water supply companies.

When installing the water connection, observe the

permitted installation areas for the pipe. For the

permitted installation areas and dimensions see

“Dimensions of the installation niche”.

Maximum outer diameter of the water pipe

(without fittings):

3

/

8

" (9.5 mm).

Appliance Maximal load at one time

Refrigerator 24" 2.0 Ampere

Refrigerator 30" 2.0 Ampere

Freezer 18" (*) 3.5 Ampere

Freezer 24" (*) 4.0 Ampere

Freezer 30" (*) 4.5 Ampere

Wine unit 18" 2.0 Ampere

Wine unit 24" 2.0 Ampere

9

Dimensions of the installation

niche

Legend:

A Area for installation of the water connection

It is recommended the water-box be placed adjacent to the installation niche, so that it can be accessed for service

without uninstalling the appliance. If this is not possible, place the recessed water box within the shaded area.

B Area for installation of the power connection

C Opening depth of niche, depending on kitchen design

C = 24" (610 mm) minimum

XY

18“ 9“

(457 mm) (229 mm)

24“ 12“

(610 mm) (305 mm)

30“ 15“

(762 mm) (381 mm)

IMPORTANT !

The side walls of the niche must be

perfectly straight. The furniture

return area has to be at least 4"

(100 mm) deep.

10

Required accessories and tools

Supplied accessories

 Installation instructions

 Operating instructions

 Installation kit

Optional accessories

Sealing Kit for Side-by-Side Installation BSEALKIT10

For permanent connection of two individual appliances,

e.g. Freezer next to Refrigerator.

Freedom

Heater Kit for Side-by-Side Installation

XHEATKIT10

If the gap between the appliances is less

than 6" (160 mm).

Panel unification part (Metal strip) FPCONNTS10

For connection of two door panels. Can be used

for standard height door panels without further

preliminary work.

Other required accessories

Ice maker installation kit

1

/

4

" OD copper line

For connecting appliances which require water,

e.g. for an ice maker.

Maximum outer diameter of the water pipe

(without fittings):

13

/

32

" (10 mm).

Miscellaneous

 Stepladder

 Dolly, hand truck

 Hammer drill for drilling holes in wall or floor

 Bits according suitable for material and in different

sizes

 Wooden beam (cross section min. 3" x 4") as an

alternative tip protection, length according to the

width of the installation niche

 Wooden screws in different sizes

 Thin plywood sheet, particle board or cardboard to

protect the floor from damage

 Suitable material for covering and protecting

furniture (e.g. protective sheets)

 Adhesive tape

Note:

Before using, check whether the removed adhesive

tape leaves adhesive residue on the work surfaces!

Otherwise do not use on high-quality work surfaces.

Tools

Cordless screwdriver

Torx bit T20 + magnetic

holder

Torx screwdriver T20

5

/

16

" (8 mm) hex nut driver

Wood drills in different sizes

Open end wrench

1

/

2

"

(SW 13 mm)

Multigrip pliers

Adjustable wrench

Cutter with adjustable blade

Metal tape measure,

folding rule

Square

Level, length 2' (60 cm) and

4' (1,2 m)

Level, min. 4' (1 ,2 m) long

11

Installation instructions

The following installation instructions describe the

installation steps for various appliance types:

 Refrigerator units

 Freezer units

 Freezer units with ice maker

 Freezer units with ice-water dispenser

 Wine storage units

Therefore the diagrams may be a general representation

of your appliance.

Particular reference is made to special installation steps

for individual appliance types.

1. Checking the installation niche

, CAUTION

Use the following check list for a safe and trouble

free installation.

1. Check the floor.

See section on “Installation/Floor”.

2. Check the dimensions of the installation niche, see

“Dimensions of the installation niche”.

3. Check that the installation niche is square.

4. Check location of the socket.

See section on “Connecting the power” and in the

section on “Dimensions of the installation niche”.

5. Check location of the water connection

(only for appliances with ice maker).

See section on “Connecting the water” and in the

section on “Dimensions of the installation niche”.

6. Check attachment of the adjacent cabinet/fixtures.

All cabinet parts in the vicinity of the appliance must

be connected securely to the wall.

7. Check that adjacent cabinet/fixtures have adequate

clearance (door opening angle).

2. Removing the packaging

, WARNING

Be careful, otherwise people who are helping may

be injured or the appliance may be damaged!

 The appliance may tip over while it is being

unpacked or if the doors are opened.

 The appliance is very heavy.

Data relating to the weight when empty is found

in the following table:

Refrigerator 24" approx. 310 Ibs/140 kg

Refrigerator 30" approx. 350 Ibs/158 kg

Freezer 18" approx. 255 Ibs/115 kg*

Freezer 24" approx. 300 Ibs/135 kg*

Freezer 30" approx. 335 Ibs/150 kg*

Wine unit 18" approx. 300 Ibs/135 kg

Wine unit 24" approx. 360 Ibs/160 kg

(* without Water Dispenser)

Note:

Check appliance for damage in transit.

Do not install the appliance if it is visibly damaged.

If in doubt, contact your dealer.

To avoid floor damage:

1. Remove the packaging carton and be careful not to

damage the surface of appliance.

2. Place packaging cardboard or plywood under the

appliance.

3. Remove accessories from the outside

of the appliance.

Save adhesive tape which was used to attach

the supplied accessories to the appliance.

It can be used subsequently for attaching an edge

protection to the installation niche walls (see section

on “A / 3. Attaching an edge protection”).

4. Remove transportation protection devices (a) and lift

appliance off the pallet – appliance is very heavy!

5. Carefully open the appliance – risk of tipping over –

and remove accessories and installation materials

from inside the appliance. Close the door again.

Note:

Do not remove transportation safety devices which

protect the shelves and storage compartments

inside the appliance until the installation is complete,

otherwise the parts may be damaged.

12

3. Transport of the appliance

, WARNING

Be careful, otherwise people who are helping may

be injured or the appliance may be damaged.

The appliance is very heavy.

The appliance is 83

1

/

8

" (2126 mm) tall. If the appliance

cannot be transported in an upright position,

the appliance can be transported horizontally.

Note:

Do not raise up the appliance via the side panels. Risk of

damage to the appliance!

When raising up the appliance, observe the required

minimum height at the installation location according to

the following table:

Note:

Always use the appliance dolly from the rear side of the

appliance. Never push it in from the front under the

appliance. Risk of damage to the appliance!

1. Transport the appliance to a suitable installation

location with suitable means of transportation

(trolley, lifting truck or hand).

2. Secure the appliance during transportation to

prevent it from tipping.

4. Installation preparation

Unpack installation materials and accessories.

To simplify installation, the packages are identified with

labels A, B and C corresponding with the manual

sections.

5. Special installation

The following symbol indicates that additional steps

need to be taken before proceeding to the next chapter.

Special installation steps are described after section C.

 Change over door hinge, see

“Changing over the door hinges”.

 Sealing mat, see “Removing/

changing over the sealing mat”

 Side-by-Side installation, see “Side-

by-Side installation”.

 Connecting the water, see “Preparing

to connect the water” an “Connecting

the water to the appliance”.

 Ice-water dispenser, see “Aligning the

ice-water dispenser“.

 Cover strips for a wine unit, see

“Attaching the cover strips”

 Door limitation pin, see “Adjusting the

door opening angle”.

Raise up via

appliance rear

Do not raise up from

appliance side

Minimum height

86"/2185 mm

Do not raise up the

appliance via the side

panels!

13

1. Attaching the anti-tip-brackets

, WARNING:

Risk of injury and damage!

Assure that there are no electrical wires or

plumbing in the area which the screws could

penetrate.

, WARNING:

Risk of injury! Always wear safety glasses and

other necessary protective devices or apparel

when installing or working with dowels.

Important note:

If a Side-by-Side set up of two appliances is envisaged,

the anti-tip brackets are needed as installation aid.

Connect the appliances before the anti-tip brackets are

fixed to the wall, see “Side-by-Side installation”.

Note:

 2 anti-tip-brackets are required for each appliance.

 The supplied set contains fastening screws for

various applications. Select the fastening screws

according to the local conditions.

 If the anti-tip brackets, and therefore the appliance,

cannot be securely attached with the supplied

fastening screws, another suitable method must be

used to attach the appliance securely.

The anti-tip-brackets (a) must overlap a minimum of

2

1

/

8

” (54 mm) over the appliance to secure the

appliance.

If this minimum length cannot be observed for structural

conditions it is possible to do this by fastening

a spacer (b) behind the anti-tip angle, e.g. a sufficiently

dimensioned wood board.

The length of the plank should correspond to the width

of the installation niche!

1. Specify the attachment points of the anti-tip-brackets

according to the section on “Dimensions of the

installation niche”.

2. Attach the anti-tip-brackets completely.

Be sure screws hold tight.

Important notes for fastening with dowels and screws:

Not recommended for use in light-weight masonry

material such as cinder block.

Not recommended for use in new concrete which has not

had time to cure.

14

2. Attaching an alternative anti-tip

device

Important note:

If the anti-tip brackets cannot be attached securely,

an alternative anti-tip-device can be attached. However,

ensure that there is no play between the appliance and

the anti-tip-device. If possible, always screw the wooden

beam to existing studs on the rear panel of the

installation niche.

1. Saw the wooden beam (cross section min. 3" x 4")

to the required length. Length is equal to the width

of the installation niche!

Note:

 If the installation niche is deeper than the

appliance, select a beam which has a larger

cross section or attach 2 beams.

 The beam must cover the appliance by

at least 2" (50.8 mm).

2. Mark the installation height (lower edge of the beam)

on the rear panel of the installation niche.

3. Select screws according to the thickness of the

wooden beam: length = min. 2.5 x beam thickness,

diameter #12 or #14.

Note:

Choose the number of screws according to the

installation niche width, thereby ensuring that the

beam can be attached securely.

4. Depending to the subsurface:

Locate wall studs in the rear of the installation niche

and accordingly transfer their location to the wooden

beam

or

fasten suitable dowel into the rear wall.

5. Predrill the wooden beam.

6. Attach the wooden beam to the rear panel of the

installation niche.

3. Attaching an edge protection

To protect the edges of the installation niche,

it is recommended to attach edge protection

made of a suitable material.

The following are special installation

steps. Instructions are provided after

section C.

 Change over door hinge, see

“Changing over the door hinges”.

 Sealing mat, see “Removing/

changing over the sealing mat”

 Side-by-Side installation, see “Side-

by-Side installation”.

 Connecting the water, see “Preparing

to connect the water”.

15

1. Pushing the appliance into the

installation niche

, CAUTION

Caution when pushing the appliance into the

installation niche. Do not damage the water line or

power cord.

Note:

When the floor or the appliance is not leveled in

comparison to the installation niche adjust height

adjustable wheels before you move the appliance into

the installation niche.

1. Remove the base panel.

2. Raise the height-adjustable wheels at the back

by approx.

3

/

8

" (10 mm).

3. Put the electric plug into the socket.

4. Push the water line into the guard tube (a) at the rear

of the appliance.

, WARNING

Be careful, otherwise people who are helping may

be injured or the appliance may be damaged.

The appliance may tip over while the water line is

pushing into the guard tube (a).

5. To prevent the power cord from becoming caught,

tie a piece of string to the middle of the power cord

and feed forwards over the top of the appliance.

When pushing in the appliance, pull the cable

upwards. Take care not to pinch the power cord.

or

Using adhesive tape, tape the power cord to the

floor centrally behind the appliance approx.

15" (380 mm) away from the rear panel of

the installation niche.

6. Carefully push the appliance into the installation

niche.

7. Remove edge protection (if attached).

16

2. Aligning the appliance in the

installation niche

Note:

To ensure that the appliance functions correctly, it must

be set perfectly levelled.

Depth alignment

The positioning aid on the door have been designed for

the following total thickness of door panels:



3

/

4

" (19 mm)

 1

1

/

2

" (38 mm)

Always take account of the possible differing thickness

of the panel fronts which are to be fitted subsequently.

1. Align the appliance with the cabinet fronts using the

positioning aid.

Place level over the positioning aid on the door.

For freezer unit with ice-water dispenser:

Freezer units with ice-water dispenser have to be set

back an additional

3

/

32

” (min. 2 mm) between front of

positioning aids and cabinet.

This is also the case for other units if they are combined

with an IWD unit in a side-by-side installation.

Height alignment

Notes:

 Do not twist or jam the appliance inside the

installation niche! When adjusting the height-

adjustable feet, proceed gradually: Always alternate

between left and right, etc.

 For easier adjustment of the rear feet take the weight

off by slightly tilting the appliance forward.

 When using a wooden beam as an alternative anti-

tip mechanism, turn the appliance as far as it will go

against the wooden beam. Do not bend against the

wooden beam.

The height-adjustable feet at the front and rear can all be

adjusted from the front.

Front: with open-ended wrench

1

/

2

"

(Width across flats 13 mm)

Rear: with

5

/

16

" (8 mm) hex nut driver via flexible

shaft.

The mark (a) attached at the appliance base is used as

a standard gage for height adjustment. When adjusting

the height, align this mark at a height of 1

1

/

2

" (32 mm)

above the floor.

It is very important to comply with this dimension for the

subsequent alignment of the furniture fronts.

The height adjustment gauge (b) is used

to set this height correctly. The upper

edge of the gauge must be in alignment

with the mark on the appliance.

2. Unscrew the feet at the front of the appliance until

the mark (a) on the appliance is in alignment with the

upper edge of the height adjustment gauge (b).

17

3. Align the appliance vertically using the feet

at the back. Use a level!

3. Attaching the appliance to the

installation niche

It is essential to attach the appliance to the top of the

installation niche.

1. Screw the attachment plate lugs (top) to the

overhead furniture.

2. If there is a fairly large gap above the appliance,

fit a wooden beam above the appliance, ensuring

that the wooden beam fits the gap exactly.

3. If there is enough room on the top of the appliance,

fix the attachment plate side lugs (top) to the side of

the niche.

4. Screw on the bars of the fastening sheets (lateral)

with the cabinet parts located next to them.

Note:

In the case of a Side-by-Side installation this

installation step is not possible. These parts have

been removed.

5. Shorten the fitting strip (a) to the required height to

fill the gap.

6. Press fitting strip (a) into the cover strip (b).

7. Attach the cover strip (b) to the attachment plate

(top).

Note:

In the case of a side-by-side installation connect both

cover rails to the bolt included in the installation

accessories for side-by-side installation.

The following is a special installation

step. Instructions are provided after

section C.

 Connecting the water, see

“Connecting the water to the

appliance”.

18

1. Attaching the toe kick panel

Note:

Risk of damage to the appliance. Do not cover ventilation

slots in the base panel.

Nominal dimensions to be observed:

Stainless steel panel (accessory)

1. Attach the base panel to the appliance (do not

screw on).

2. Remove the protective film from the adhesive pads.

3. Fit the toe kick panel to the base panel and press

firmly into place.

Wooden panel

1. If required, shorten wooden panel to the required

length.

2. Screw wooden panel to the base panel from behind.

There are already screw holes in the base panel.

2. Aligning the base panel

1. Put on the base panel (do not screw on) and

measure the difference in depth A between the base

panel and toe kick panel of the adjacent cabinet.

2. Remove the base panel.

3. Adjust the brackets (a) to the dimensions A and

tighten.

4. Attach the base panel.

19

3. Switching the appliance ON

To guarantee the accuracy of the following working steps

and thus the appearance of the overall kitchen front later

on, the appliance should now be operated.

1. Open the appliance door.

2. Press the POWER button.

3. Press the POWER button again to shut off.

Only for appliances with a water connection:

In order to avoid the risk of damage caused by leaking

water from damage possibly caused to the water pipe

feeding the appliance, keep the shut-off valve closed.

4. Preparing the door panels

Important note:

When performing any work on the door panels, always

observe the following:

 Always screw into the best load-bearing material of

the door panel.

 Never screw into fillers, decorative strips or similar.

 Select a screw length which is always shorter than

the thickness of the door panel.

 To prevent damage, protect surfaces of the door

panels during installation.

The total weight of the door panel must not exceed the

following values:

 18" Appliance 44 Ibs/20 kg (19 lbs/8.5 kg *)

 24" Appliance 55 Ibs/25 kg (32 lbs/14.5 kg *)

 30" Appliance 64 Ibs/29 kg

(* Wine unit)

Important information for furniture doors with cutout

(appliances with ice and water dispenser, wine storage

cabinets):

The cut edges of the door cutout must be protected

before humidity penetrates. To do this, use the means

suitable for the material and the shape of the furniture

door (e. g. edge veneer, edge sealant).

5. Loading the appliance door

When attaching the door panels, it is recommended to

load the door storage compartments in the appliance

with weights in order to ensure that the gap width is as

precise as possible.

Recommendations:

 18" Appliance: 22 lbs/10 kg

 24" Appliance: 33 lbs/15 kg

 30" Appliance: 44 lbs/20 kg

6. Removing the installation support

part

Unscrew the positioning aid from the appliance door.

Note:

Store the positioning aids, there will be used in an

installation step later.

20

7. Attaching the adjusting rail to

the door panel

1. Measure the distance A between the adjusting rail

and the overhead cabinet/fixtures.

2. Loosen the 2 nuts (a) and remove the adjusting

rail (b).

3. Mark this amount A on the rear of the door panel.

4. Determine and mark the centerline of the door panel.

5. Put on the adjusting rail and align along the marks.

Mark the drill holes.

6. Drill the holes.

7. Screw on the adjusting rail tightly.

Notes:

 Attach the adjusting rail to the door panel with at

least 10 screws. One screw should be inserted

under each double threaded bolt.

 The adjusting rail features a variety of holes for the

many different design options of door panels.

Always screw into the best load-bearing material of

the door panel.

8. Attaching the fixation strips to the

door panel

Note:

The fixation strips are pre-assembled for stainless steel

doors. In this case continue with the next installation step

(“C / 9. Attaching the door panel”).

1. Hang the door panel on the double threaded

bolt (a).

2. Align the door panel with the double threaded bolts

(Torx screwdriver).

Re-examine the dimensions of the gap continuously.

Use the height adjustment gauge (b).

3. Transfer the middle drill holes along the outer edge

of the appliance door to the door panel and mark.

4. Remove the door panel.

La page charge ...

Thermador ZOME30ABS Guide d'installation

Ce manuel convient également à

Thermador ZOME30ABS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents