Husqvarna 135 Manuel utilisateur

135, 135e

135e TrioBrake

DK Brugsanvisning,

216-239

NO Bruksanvisning,

240-263

FI Käyttöohje,

264-289

EE

Käsitsemisõpetus

,

290-312

LV

Lieto‰anas pamÇc¥ba

,

313-335

LT

Naudojimosi instrukcijos

,

336-359

SI

Navodila za uporabo

,

360-382

EN Operator's Manual,

7-30

FR Manuel d'utilisation,

31-57

NL Gebruiksaanwijzing,

58-84

IT Istruzioni per l’uso,

85-110

ES Manual de instrucciones,

111-137

DE Bedienungsanweisung,

138-164

PT Instruções para o uso,

165-191

SE Bruksanvisning,

192-215

2

1155296-38 Rev.1 2012-11-19

1

5

7

8

9

10

11

12

13

14

15

16

17

2

3

4

B

E

6

18

3

1155296-38 Rev.1 2012-11-19

19

20

25

24

23

22

21

27

28

29

30

31

32

33

26

35

37

36

38

39

40

41

34

4

1155296-38 Rev.1 2012-11-19

42

43

53

52

51

54

49

48

474645

44

50

59

5857

5655

60

61 62

63

64

5

1155296-38 Rev.1 2012-11-19

85

6

1155296-38 Rev.1 2012-11-19

107

KEY TO SYMBOLS

English

–

7

1155296-38 Rev.1 2012-11-19

Symbols on the machine:

WARNING! Chain saws can be

dangerous! Careless or incorrect use can

result in serious or fatal injury to the

operator or others.

Please read the operator’s manual

carefully and make sure you

understand the instructions before

using the machine.

Always wear:

• Approved protective helmet

• Approved hearing protection

• Protective goggles or a visor

This product is in accordance with

applicable EC directives.

Noise emission to the environment

according to the European

Community’s Directive. The machine’s

emission is speciﬁed in the Technical

data chapter and on the label.

WARNING! Kickback may occur when

the nose or tip of the guide bar touches

an object, and cause a lightning fast

reverse reaction, kicking the guide bar

up and towards the operator. May cause

serious personal injury.

Chain brake, activated (right) Chain

brake, not activated (left)

Refuelling.

Chain oil ﬁll.

Ignition; choke:

Set the choke control

in the choke position. This should

automatically set the stop switch to the

start position.

Air purge

Other symbols/decals on the machine refer to special

certiﬁcation requirements for certain markets.

Symbols in the operator’s

manual:

Switch off the engine before

carrying out any checks or

maintenance. CAUTION! The

start/stop switch automatically

returns to run position. In order to

prevent unintentional starting, the

spark plug cap must be removed

from the spark plug when

assembling, checking and/or

performing maintenance.

Always wear approved protective

gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be

worn.

Refuelling.

Filling with oil and adjusting oil ﬂow.

The chain brake must be engaged

when the chain saw is started.

WARNING! Kickback may occur when

the nose or tip of the guide bar touches

an object, and cause a lightning fast

reverse reaction, kicking the guide bar

up and towards the operator. May cause

serious personal injury.

INTRODUCTION

8 – English

1155296-38 Rev.1 2012-11-19

Dear Customer,

Congratulations on your choice to buy a Husqvarna

product! Husqvarna is based on a tradition that dates

back to 1689, when the Swedish King Karl XI ordered the

construction of a factory on the banks of the Husqvarna

River, for production of muskets. The location was logical,

since water power was harnessed from the Huskvarna

River to create the water-powered plant. During the more

than 300 years in existence, the Husqvarna factory has

produced a lot of different products, from wood stoves to

modern kitchen appliances, sewing machines, bicycles,

motorcycles etc. In 1956, the ﬁrst motor driven lawn

mowers appeared, followed by chain saws in 1959, and it

is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in

the world of forest and garden products, with quality as

our highest priority. The business concept is to develop,

manufacture and market motor-driven products for

forestry and gardening, as well as for the building and

construction industry. Husqvarna

′

s aim is also to be at the

front edge for ergonomics, usability, security and

environmental protection. That is the reason why we have

developed many different features to add to our products

within these areas.

We are convinced that you will appreciate with great

satisfaction the quality and performance of our product for

a very long time to come. The purchase of one of our

products gives you access to professional help with

repairs and service whenever this may be necessary. If

the retailer who sells your machine is not one of our

authorised dealers, ask for the address of your nearest

service workshop.

It is our wish that you will be satisﬁed with your product

and that it will be your companion for a long time. Think of

this operator

′

s manual as a valuable document. By

following its content (usage, service, maintenance, etc),

the life span and the second-hand value of the machine

can be extended. If you sell this machine, make sure that

the operator

′

s manual is passed on to the buyer.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product

development and therefore reserves the right to modify

the design and appearance of products without prior

notice.

What is what on the chain saw? (1)

1 Cylinder cover

2 Air purge

3 Start reminder

4 Right-hand brake trigger (135e TrioBrake)

5 Combined start and stop switch

6 Information and warning decal

7 Fuel tank

8 Adjuster screws carburettor

9 Starter handle

10 Starter

11 Chain oil tank

12 Product and serial number plate

13 Felling direction mark

14 Front handle

15 Front hand guard

16 Mufﬂer

17 Saw chain

18 Bar tip sprocket

19 Guide bar

20 Spike bumper

21 Chain catcher

22 Chain tensioning screw

23 Clutch cover (135)

24 Rear handle with right hand guard

25 Throttle trigger

26 Throttle lockout

27 Clutch cover (135e, 135e TrioBrake)

28 Chain tensioner wheel

29 Knob

30 Operator

′

s manual

31 Guide bar cover

32 Combination spanner

GENERAL SAFETY PRECAUTIONS

English

–

9

1155296-38 Rev.1 2012-11-19

Before using a new chain saw

• Please read this manual carefully.

•

(1)

-

(107)

refer to ﬁgures on p. 2-6.

• Check that the cutting equipment is correctly ﬁtted and

adjusted. See instructions under the heading

Assembly.

• Refuel and start the chain saw. See the instructions

under the headings Fuel Handling and Starting and

Stopping.

• Do not use the chain saw until sufﬁcient chain oil has

reached the chain. See instructions under the heading

Cutting equipment.

• Long-term exposure to noise can result in permanent

hearing impairment. So always use approved hearing

protection.

Important

!

WARNING! Under no circumstances may

the design of the machine be modiﬁed

without the permission of the

manufacturer. Always use original

accessories. Non-authorized

modiﬁcations and/or accessories can

result in serious personal injury or the

death of the operator or others.

!

WARNING! A chain saw is a dangerous

tool if used carelessly or incorrectly and

can cause serious, even fatal injuries. It

is very important that you read and

understand the contents of this

operator’s manual.

!

WARNING! The inside of the mufﬂer

contain chemicals that may be

carcinogenic. Avoid contact with these

elements in the event of a damaged

mufﬂer.

!

WARNING! Long term inhalation of the

engine’s exhaust fumes, chain oil mist

and dust from sawdust can represent a

health risk.

!

WARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants. To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants to consult their physician and

the medical implant manufacturer before

operating this machine.

!

WARNING! Never allow children to use or

be in the vicinity of the machine. As the

machine is equipped with a spring-

loaded stop switch and can be started by

low speed and force on the starter

handle, even small children under some

circumstances can produce the force

necessary to start the machine. This can

mean a risk of serious personal injury.

Therefore remove the spark plug cap

when the machine is not under close

supervision.

IMPORTANT!

This chain saw for forest service is designed for forest

work such as felling, limbing and cutting.

You should only use the saw with the bar and chain

combinations we recommend in the chapter Technical

data.

Never use the machine if you are fatigued, while under

the inﬂuence of alcohol or drugs, medication or anything

that could affect your vision, alertness, coordination or

judgement.

Wear personal protective equipment. See instructions

under the ”Personal protective equipment” heading.

Do not modify this product or use it if it appears to have

been modiﬁed by others.

Never use a machine that is faulty. Carry out the safety

checks, maintenance and service instructions

described in this manual. Some maintenance and

service measures must be carried out by trained and

qualiﬁed specialists. See instructions under the

Maintenance heading.

Never use any accessories other than those

recommended in this manual. See instructions under

the headings Cutting equipment and Technical data.

CAUTION! Always wear protective glasses or a face

visor to reduce the risk of injury from thrown objects. A

chain saw is capable of throwing objects, such as wood

chips, small pieces of wood, etc, at great force. This can

result in serious injury, especially to the eyes.

!

WARNING! Running an engine in a

conﬁned or badly ventilated area can

result in death due to asphyxiation or

carbon monoxide poisoning.

!

WARNING! Faulty cutting equipment or

the wrong combination of bar and saw

chain increases the risk of kickback!

Only use the bar/saw chain combinations

we recommend, and follow the ﬁling

instructions. See instructions under the

heading Technical data.

GENERAL SAFETY PRECAUTIONS

10 – English

1155296-38 Rev.1 2012-11-19

Always use common sense (2)

It is not possible to cover every conceivable situation you

can face when using a chain saw. Always exercise care

and use your common sense. Avoid all situations which

you consider to be beyond your capability. If you still feel

uncertain about operating procedures after reading these

instructions, you should consult an expert before

continuing. Do not hesitate to contact your dealer or us if

you have any questions about the use of the chain saw.

We will willingly be of service and provide you with advice

as well as help you to use your chain saw both efﬁciently

and safely. Attend a training course in chain saw usage if

possible. Your dealer, forestry school or your library can

provide information about which training materials and

courses are available. Work is constantly in progress to

improve the design and technology - improvements that

increase your safety and efﬁciency. Visit your dealer

regularly to see whether you can beneﬁt from new

features that have been introduced.

Personal protective equipment

• Approved protective helmet

• Hearing protection

• Protective goggles or a visor

• Gloves with saw protection

• Trousers with saw protection

• Boots with saw protection, steel toe-cap and non-slip

sole

• Always have a ﬁrst aid kit nearby.

• Fire Extinguisher and Shovel

Generally clothes should be close-ﬁtting without

restricting your freedom of movement.

Machine

′′

s safety equipment

In this section the machine’s safety features and their

function are explained. For inspection and maintenance

see instructions under the heading Checking, maintaining

and servicing chain saw safety equipment. See

instructions under the heading, What is what?, to ﬁnd

where these parts are located on your machine.

The life span of the machine can be reduced and the risk

of accidents can increase if machine maintenance is not

carried out correctly and if service and/or repairs are not

carried out professionally. If you need further information

please contact your nearest service workshop.

Chain brake and front hand guard

Your chain saw is equipped with a chain brake that is

designed to stop the chain if you get a kickback. The chain

brake reduces the risk of accidents, but only you can

prevent them.

(3)

Take care when using your saw and make sure the

kickback zone of the bar never touches any object.

(4)

• The chain brake (A) can either be activated manually

(by your left hand) or automatically by the inertia

release mechanism.

(5)

• The brake is applied when the front hand guard (B) is

pushed forwards or when the right-hand brake trigger

(E) is pushed up and forwards.

(6)

• This movement activates a spring-loaded mechanism

that tightens the brake band (C) around the engine

drive system (D) (clutch drum).

(7)

• The front hand guard is not designed solely to activate

the chain brake. Another important feature is that it

reduces the risk of your left hand hitting the chain if

you lose grip of the front handle.

• The chain brake must be engaged when the chain

saw is started to prevent the saw chain from rotating.

(46)

• Use the chain brake as a ”parking brake” when

starting and when moving over short distances, to

reduce the risk of moving chain accidentally hitting

your leg or anyone or anything close by. Do not leave

the chain saw switched on with the chain brake

activated for long periods. The chain saw can become

very hot.

• The chain brake is released by moving the front hand

guard marked ”PULL BACK TO RESET” back,

towards the front handle.

(38)

• Kickback can be very sudden and violent. Most

kickbacks are minor and do not always activate the

chain brake. If this happens you should hold the chain

saw ﬁrmly and not let go.

(51)

• The way the chain brake is activated, either manually

or automatically by the inertia release mechanism,

depends on the force of the kickback and the position

of the chain saw in relation to the object that the

kickback zone of the bar strikes.

!

WARNING! Most chain saw accidents

happen when the chain touches the

operator. You must use approved

personal protective equipment whenever

you use the machine. Personal protective

equipment cannot eliminate the risk of

injury but it will reduce the degree of

injury if an accident does happen. Ask

your dealer for help in choosing the right

equipment.

IMPORTANT! Sparks can come from the mufﬂer, the bar

and chain or other sources. Always have ﬁre

extinguishing tools available if you should need them.

Help prevent forest ﬁres.

!

WARNING! Never use a machine with

defective safety components. Safety

equipment must be inspected and

maintained. See instructions under the

heading Checking, maintaining and

servicing chain saw safety equipment. If

your machine does not pass all the

checks, take the saw to a servicing

dealer for repair.

GENERAL SAFETY PRECAUTIONS

English

–

11

1155296-38 Rev.1 2012-11-19

If you get a violent kickback while the kickback zone of

the bar is farthest away from you the chain brake is

designed to be activated by the inertia in the kickback

direction.

(8)

If the kickback is less violent or the kickback zone of

the bar is closer to you the chain brake will be

activated manually by the movement of your left hand.

• In the felling position the left hand is in a position that

makes manual activation of the chain brake

impossible. With this type of grip, that is when the left

hand is placed so that it cannot affect the movement

of the front hand guard, the chain brake can only be

activated by the inertia action.

(9)

Will my hand always activate the chain

brake during a kickback?

No. It takes a certain force to move the hand guard

forward. If your hand only lightly touches the front guard

or slips over it, the force may not be enough to trigger the

chain brake. You should also maintain a ﬁrm grip of the

chain saw handles while working. If you do and

experience a kickback, your hand may never leave the

front handle and will not activate the chain brake, or the

chain brake will only activate after the saw has swung

around a considerable distance. In such instances, the

chain brake might not have enough time to stop the saw

chain before it touches you.

There are also certain positions in which your hand

cannot reach the front hand guard to activate the chain

brake; for example, when the saw chain is held in felling

position.

Will my inertia activated chain brake

always activate during kickback in the

event of a kickback?

No. First your brake must be in working order. Testing the

brake is simple, see instructions under the heading

Checking, maintaining and servicing chain saw safety

equipment. We recommend you do before you begin each

work session. Second the kickback must be strong

enough to activate the chain brake. If the chain brake is

too sensitive it would activate all the time which would be

a nuisance.

Will my chain brake always protect me

from injury in the event of a kickback?

No. First, the chain brake must be in working order to

provide the intended protection. Second, it must be

activated during the kickback as described above to stop

the saw chain. Third, the chain brake may be activated but

if the bar is too close to you the brake might not have

enough time to slow down and stop the chain before the

chain saw hits you.

Only you and proper working technique can eliminate

kickback and its danger.

Throttle lockout

The throttle lockout is designed to prevent accidental

operation of the throttle control. When you press the lock

(A) (i.e. when you grasp the handle) it releases the throttle

control (B). When you release the handle the throttle

control and the throttle lockout both move back to their

original positions. This arrangement means that the

throttle control is automatically locked at the idle setting.

(10)

Chain catcher

The chain catcher is designed to catch the chain if it snaps

or jumps off. This should not happen if the chain is

properly tensioned (see instructions under the heading

Assembly) and if the bar and chain are properly serviced

and maintained (see instructions under the heading

General working instructions).

(11)

Right hand guard

Apart from protecting your hand if the chain jumps or

snaps, the right hand guard stops branches and twigs

from interfering with your grip on the rear handle.

(12)

Vibration damping system

Your machine is equipped with a vibration damping

system that is designed to minimize vibration and make

operation easier.

The machine

′

s vibration damping system reduces the

transfer of vibration between the engine unit/cutting

equipment and the machine

′

s handle unit. The body of the

chain saw, including the cutting equipment, is insulated

from the handles by vibration damping units.

Cutting hardwoods (most broadleaf trees) creates more

vibration than cutting softwoods (most conifers). Cutting

with cutting equipment that is blunt or faulty (wrong type

or badly sharpened) will increase the vibration level.

Stop switch

Use the stop switch to switch off the engine.

(13)

!

WARNING! Overexposure to vibration

can lead to circulatory damage or nerve

damage in people who have impaired

circulation. Contact your doctor if you

experience symptoms of overexposure

to vibration. Such symptoms include

numbness, loss of feeling, tingling,

pricking, pain, loss of strength, changes

in skin colour or condition. These

symptoms normally appear in the

ﬁngers, hands or wrists. These

symptoms may be increased in cold

temperatures.

GENERAL SAFETY PRECAUTIONS

12 – English

1155296-38 Rev.1 2012-11-19

Mufﬂer

The mufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user.

In areas with a hot, dry climate there is a high risk of ﬁres.

These areas are sometimes subject to government rules

requiring among other things the mufﬂer must be

equipped with an approved type of spark arrestor mesh.

(14)

When ﬁtting the mesh, make sure that the mesh is

inserted in the right position. If necessary, use the

combination spanner to insert or remove the mesh.

Cutting equipment

This section describes how to choose and maintain your

cutting equipment in order to:

• Reduce the risk of kickback.

• Reduce the risk of the saw chain breaking or jumping

off the bar.

• Obtain optimal cutting performance.

• Extend the life of cutting equipment.

• Avoid increasing vibration levels.

General rules

•

Only use cutting equipment recommended by us!

See instructions under the heading Technical data.

•

Keep the chain’s cutting teeth properly

sharpened! Follow our instructions and use the

recommended ﬁle gauge.

A damaged or badly

sharpened chain increases the risk of accidents.

•

Maintain the correct depth gauge setting! Follow

our instructions and use the recommended depth

gauge clearance.

Too large a clearance increases

the risk of kickback.

•

Keep the chain properly tensioned!

If the chain is

slack it is more likely to jump off and lead to increased

wear on the bar, chain and drive sprocket.

•

Keep cutting equipment well lubricated and

properly maintained!

A poorly lubricated chain is

more likely to break and lead to increased wear on the

bar, chain and drive sprocket.

Cutting equipment designed to reduce

kickback

The only way to avoid kickback is to make sure that the

kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback

reduction and keeping the chain sharp and well-

maintained you can reduce the effects of kickback.

Guide bar

The smaller the tip radius the lower the chance of

kickback.

Saw chain

A chain is made up of a number of links, which are

available in standard and low-kickback versions.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment,

you should replace a worn or damaged bar or chain with

a bar and chain combinations recommended by

Husqvarna. See instructions under the heading Technical

Data for a list of replacement bar and chain combinations

we recommend.

Guide bar

• Length (inches/cm)

• Number of teeth on bar tip sprocket (T).

• Chain pitch (inches). The spacing between the drive

links of the chain must match the spacing of the teeth

on the bar tip sprocket and drive sprocket. (15)

• Number of drive links. The number of drive links is

determined by the length of the bar, the chain pitch

and the number of teeth on the bar tip sprocket.

!

WARNING! The exhaust fumes from the

engine are hot and may contain sparks

which can start a ﬁre. Never start the

machine indoors or near combustible

material!

CAUTION! The mufﬂer gets very hot during and after

use. This also applies during idling. Be aware of the ﬁre

hazard, especially when working near ﬂammable

substances and/or vapours.

!

WARNING! Never use a saw without a

mufﬂer, or with a damaged mufﬂer. A

damaged mufﬂer may substantially

increase the noise level and the ﬁre

hazard. Keep ﬁre ﬁghting equipment

handy. If a spark arrestor screen is

required in your area, never use the saw

without or with a broken spark arrestor

screen.

!

WARNING! Faulty cutting equipment or

the wrong combination of bar and saw

chain increases the risk of kickback!

Only use the bar/saw chain combinations

we recommend, and follow the ﬁling

instructions. See instructions under the

heading Technical data.

IMPORTANT! No saw chain design eliminates the

danger of kickback.

!

WARNING! Any contact with a rotating

saw chain can cause extremely serious

injuries.

GENERAL SAFETY PRECAUTIONS

English – 13

1155296-38 Rev.1 2012-11-19

• Bar groove width (inches/mm). The groove in the bar

must match the width of the chain drive links.

• Chain oil hole and hole for chain tensioner. The bar

must be matched to the chain saw design. (16)

Saw chain

• Chain pitch (inches) (15)

• Drive link width (mm/inches) (18)

• Number of drive links. (17)

Sharpening your chain and adjusting

depth gauge setting

General information on sharpening cutting teeth

• Never use a blunt chain. When the chain is blunt you

have to exert more pressure to force the bar through

the wood and the chips will be very small. If the chain

is very blunt it will produce wood powder and no chips

or shavings.

• A sharp chain eats its way through the wood and

produces long, thick chips or shavings.

• The cutting part of the chain is called the cutter and

consists of a cutting tooth (A) and the depth gauge

(B). The cutters cutting depth is determined by the

difference in height between the two (depth gauge

setting). (23)

When you sharpen a cutting tooth there are four important

factors to remember.

1 Filing angle (21)

2 Cutting angle (20)

3 File position (22)

4 Round ﬁle diameter

It is very difﬁcult to sharpen a chain correctly without the

right equipment. We recommend that you use our ﬁle

gauge. This will help you obtain the maximum kickback

reduction and cutting performance from your chain. (22)

See instructions under the heading Technical data for

information about sharpening your chain.

Sharpening cutting teeth

To sharpen cutting teeth you will need a round ﬁle and a

ﬁle gauge. See instructions under the heading Technical

data for information on the size of ﬁle and gauge that are

recommended for the chain ﬁtted to your chain saw.

• Check that the chain is correctly tensioned. A slack

chain will move sideways, making it more difﬁcult to

sharpen correctly.

• Always ﬁle cutting teeth from the inside face. Reduce

the pressure on the return stroke. File all the teeth on

one side ﬁrst, then turn the chain saw over and ﬁle the

teeth on the other side.

• File all the teeth to the same length. When the length

of the cutting teeth is reduced to 4 mm (5/32") the

chain is worn out and should be replaced. (23)

General advice on adjusting depth gauge setting

• When you sharpen the cutting tooth (A) the depth

gauge setting (C) will decrease. To maintain optimal

cutting performance the depth gauge (B) has to be

ﬁled down to achieve the recommended depth gauge

setting. See instructions under the heading Technical

data to ﬁnd the correct depth gauge setting for your

particular chain. (24)

Adjustment of depth gauge setting

• The cutting teeth should be newly sharpened before

adjusting the depth gauge setting. We recommend

that you adjust the depth gauge setting every third

time you sharpen the cutting teeth. NOTE! This

recommendation assumes that the length of the

cutting teeth is not reduced excessively.

• You will need a ﬂat ﬁle and a depth gauge tool. We

recommend that you use our depth gauge tool to

acheive the correct depth gauge setting and bevel for

the depth gauge.

• Place the depth gauge tool over the chain. Detailed

information regarding the use of the depth gauge tool,

will be found on the package for the depth gauge tool.

Use the ﬂat ﬁle to ﬁle off the tip of the depth gauge that

protrudes through the depth gauge tool. The depth

gauge setting is correct when you no longer feel

resistance as you draw the ﬁle along the depth gauge

tool. (24)

Tensioning the chain

The more you use a chain the longer it becomes. It is

therefore important to adjust the chain regularly to take up

the slack.

!

WARNING! Departure from the

sharpening instructions considerably

increases the risk of kickback.

!

WARNING! The risk of kickback is

increased if the depth gauge setting is

too large!

!

WARNING! A slack chain may jump off

and cause serious or even fatal injury.

GENERAL SAFETY PRECAUTIONS

14 – English

1155296-38 Rev.1 2012-11-19

Check the chain tension every time you refuel. NOTE! A

new chain has a running-in period during which you

should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight

that you cannot pull it round freely by hand. (25)

135

• Loosen the bar nut that holds the clutch cover and

chain brake. Use the combination spanner. Then

retighten the bar nut as tightly as you can by hand.

(26)

• Raise the tip of the bar and stretch the chain by

tightening the chain tensioning screw using the

combination spanner. Tighten the chain until it does

not sag from the underside of the bar. (27)

• Use the combination spanner to tighten the bar nut

while holding up the tip of the bar. Check that you can

pull the saw chain round freely by hand, and that there

is no slack on the underside of the bar. (28)

The position of the chain tensioning screw on our chain

saws varies from model to model. See instructions under

the heading What is what? to ﬁnd out where it is on your

model.

135e, 135e TrioBrake

• Release the knob by folding it out. (29)

• Turn the knob anti clockwise to loosen the bar cover.

(30)

• Adjust the tension on the chain by turning the wheel

down (+) for tighter tension and up (-) to loosen the

tension. (31)

• Tighten the bar clutch by turning the knob clockwise.

(32)

• Fold the knob back in to lock the tensioning. (33)

Lubricating cutting equipment

Chain oil

Chain oil must demonstrate good adhesion to the chain

and also maintain its ﬂow characteristics regardless of

whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an

optimal chain oil which, with its vegetable oil base, is also

biodegradable. We recommend the use of our own oil for

both maximum chain life and to minimise environmental

damage. If our own chain oil is not available, standard

chain oil is recommended.

Never use waste oil! Using waste oil can be dangerous

to you and damage the machine and environment.

Filling with chain oil

• All our chain saws have an automatic chain lubrication

system. On some models the oil ﬂow is also

adjustable.

• The saw chain oil tank and the fuel tank are designed

so that the fuel runs out before the saw chain oil.

However, this safety feature requires that you use the

right sort of chain oil (if the oil is too thin it will run out

before the fuel), and that you adjust the carburetor as

recommended (a lean mixture may mean that the fuel

lasts longer than the oil) and that you also use the

recommended cutting equipment (a bar that is too

long will use more chain oil).

Checking chain lubrication

• Check the chain lubrication each time you refuel. See

instructions under the heading Lubricating the bar tip

sprocket.

Aim the tip of the bar at a light coloured surface about

20 cm (8 inches) away. After 1 minute running at 3/4

throttle you should see a distinct line of oil on the light

surface.

If the chain lubrication is not working:

• Check that the oil channel in the bar is not obstructed.

Clean if necessary. (34)

• Check that the groove in the edge of the bar is clean.

Clean if necessary. (35)

• Check that the bar tip sprocket turns freely and that

the lubricating hole in the tip sprocket is not blocked.

Clean and lubricate if necessary. (36)

If the chain lubrication system is still not working after

carrying out the above checks and associated measures

you should contact your service agent.

Chain drive sprocket

The clutch drum is ﬁtted with one of the following drive

sprockets:

A Spur sprocket (the chain sprocket is welded on the

drum)

B Rim sprocket (replaceable) (37)

Regularly check the degree of wear on the drive sprocket.

Replace if wear is excessive. Replace the drive sprocket

whenever you replace the chain.

!

WARNING! Poor lubrication of cutting

equipment may cause the chain to snap,

which could lead to serious, even fatal

injuries.

IMPORTANT! When using vegetable based saw chain

oil, dismantle and clean the groove in the bar and saw

chain before long-term storage. Otherwise there is a risk

of the saw chain oil oxidizing, which will result in the saw

chain becoming stiff and the bar tip sprocket jamming.

GENERAL SAFETY PRECAUTIONS

English – 15

1155296-38 Rev.1 2012-11-19

Needle bearing lubrication

Both versions of sprockets have a needle bearing on the

drive shaft, which has to be greased regularly (once a

week). CAUTION! Use a high-quality bearing grease or

engine oil.

See instructions under the heading Maintenance, Needle

bearing lubrication.

Checking wear on cutting equipment

Check the chain daily for:

• Visible cracks in rivets and links.

• Whether the chain is stiff.

• Whether rivets and links are badly worn.

Replace the saw chain if it exhibits any of the points

above.

We recommend you compare the existing chain with a

new chain to decide how badly the existing chain is worn.

When the length of the cutting teeth has worn down to

only 4 mm the chain must be replaced.

Guide bar

Check regularly:

• Whether there are burrs on the edges of the bar.

Remove these with a ﬁle if necessary.

• Whether the groove in the bar has become badly

worn. Replace the bar if necessary.

• Whether the tip of the bar is uneven or badly worn. If

a hollow forms on the underside of the bar tip this is

due to running with a slack chain.

• To prolong the life of the bar you should turn it over

regularly.

!

WARNING! Most chain saw accidents

happen when the chain touches the

operator.

Wear personal protective equipment. See

instructions under the ”Personal

protective equipment” heading.

Do not tackle any job that you feel you

are not adequately trained for. See

instructions under the headings

Personal protective equipment, How to

avoid kickback, Cutting equipment and

General working instructions.

Avoid situations where there is a risk of

kickback. See instructions under the

heading Machine

′′

s safety equipment.

Use the recommended protective

equipment and check its condition. See

instructions under the heading General

working instructions.

Check that all the chain saw safety

features are working. See instructions

under the headings General working

instructions and General safety

precautions.

ASSEMBLY

16 – English

1155296-38 Rev.1 2012-11-19

Fitting the bar and chain

135

Check that the chain brake is in disengaged position by

moving the front hand guard towards the front handle.

(38)

Unscrew the bar nut and remove the clutch cover (chain

brake). Take off the transportation ring (A). (39)

Fit the bar over the bar bolt. Place the bar in its rearmost

position. Place the chain over the drive sprocket and in the

groove on the bar. Begin on the top side of the bar. (40)

Make sure that the edges of the cutting links are facing

forward on the top edge of the bar.

Mount the clutch cover and remember to ﬁt the chain

adjuster pin in the hole in the bar. Check that the drive

links of the chain ﬁt correctly over the drive sprocket and

that the chain is correctly located in the groove in the bar.

Tighten the bar nut with your ﬁngers.

Tension the chain by turning the chain tensioning screw

clockwise using the combination spanner. The chain

should be tensioned until it does not sag from the

underside of the bar. (27)

The chain is correctly tensioned when there is no slack on

the underside of the bar, and it can still be turned easily

by hand. Tighten the bar nut with the combination spanner

while holding up the tip of the bar. (28)

When ﬁtting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check the

chain tension regularly. A correctly tensioned chain

ensures good cutting performance and long life. (25)

135e, 135e TrioBrake

Check that the chain brake is in disengaged position by

moving the front hand guard towards the front handle.

(38)

Loosen the chain tensioner wheel and remove the clutch

cover (chain brake). Remove the transport guard. (A) (41)

Fit the bar over the bar bolts. Place the bar in its rearmost

position. Place the chain over the drive sprocket locate it

in the groove on the bar. Begin on the top edge of the bar.

(40)

Make sure that the edges of the cutting links are facing

forward on the top edge of the bar.

Mount the clutch cover and remember to ﬁt the chain

adjuster pin in the hole in the bar. Check that the drive

links of the chain ﬁt correctly over the drive sprocket and

that the chain is correctly located in the groove in the bar.

Tension the chain by turning the wheel down (+). The

chain should be tensioned until it does not sag from the

underside of the bar. (31)

The chain is correctly tensioned when it does not sag from

the underside of the bar, but can still be turned easily by

hand. Hold up the bar tip and tighten the bar knob by

turning the knob clockwise. (32)

When ﬁtting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check the

chain tension regularly. A correctly tensioned chain

ensures good cutting performance and long life. (25)

Fitting a spike bumper

To ﬁt a spike bumper – contact your service agent. (42)

!

WARNING! Always wear gloves, when

working with the chain.

FUEL HANDLING

English – 17

1155296-38 Rev.1 2012-11-19

Fuel

Note! The machine is equipped with a two-stroke engine

and must always be run using a mixture of petrol and two-

stroke oil. It is important to accurately measure the

amount of oil to be mixed to ensure that the correct

mixture is obtained. When mixing small amounts of fuel,

even small inaccuracies can drastically affect the ratio of

the mixture.

Petrol

• Use good quality unleaded or leaded petrol.

• The lowest recommended octane grade is 90 (RON).

If you run the engine on a lower octane grade than 90

so-called knocking can occur. This gives rise to a high

engine temperature and increased bearing load,

which can result in serious engine damage.

• When working with continuous high revs (e.g. limbing)

a higher octane is recommended.

Environment fuel

HUSQVARNA recommends the use of alkylate fuel, either

Aspen two-stroke fuel or environmental fuel for four-stroke

engines blended with two-stroke oil as set out below. Note

that carburettor adjustment may be necessary when

changing the type of fuel (see the instructions under the

heading Carburettor).

Ethanol fuel

HUSQVARNA recommends commercial available fuel

with maximum 10% ethanol content.

Running-in

Avoid running at a too high speed for extended periods

during the ﬁrst 10 hours.

Two-stroke oil

• For best results and performance use HUSQVARNA

two-stroke engine oil, which is specially formulated for

our air-cooled two-stroke engines.

• Never use two-stroke oil intended for water-cooled

engines, sometimes referred to as outboard oil (rated

TCW).

• Never use oil intended for four-stroke engines.

• A poor oil quality and/or too high oil/fuel ratio may

jeopardise function and decrease the life time of

catalytic converters.

Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB formulated

for air-cooled, two-stroke engines.

Mixing

• Always mix the petrol and oil in a clean container

intended for fuel.

• Always start by ﬁlling half the amount of the petrol to

be used. Then add the entire amount of oil. Mix

(shake) the fuel mixture. Add the remaining amount of

petrol.

• Mix (shake) the fuel mixture thoroughly before ﬁlling

the machine’s fuel tank.

• Do not mix more than one month’s supply of fuel at a

time.

• If the machine is not used for some time the fuel tank

should be emptied and cleaned.

Chain oil

• We recommend the use of special oil (chain oil) with

good adhesion characteristics. (43)

• Never use waste oil. This results in damage to the oil

pump, the bar and the chain.

• It is important to use oil of the right grade (suitable

viscosity range) to suit the air temperature.

• In temperatures below 0°C (32°F) some oils become

too viscous. This can overload the oil pump and result

in damage to the oil pump components.

• Contact your service agent when choosing chain oil.

!

WARNING! Always ensure there is

adequate ventilation when handling fuel.

Petrol, litre Two-stroke oil, litre

2% (1:50) 3% (1:33)

5 0,10 0,15

10 0,20 0,30

15 0,30 0,45

20 0,40 0,60

FUEL HANDLING

18 – English

1155296-38 Rev.1 2012-11-19

Fueling

Clean the area around the fuel cap. Clean the fuel and

chain oil tanks regularly. The fuel ﬁlter must be replaced

at least once a year. Contamination in the tanks causes

malfunction. Make sure the fuel is well mixed by shaking

the container before refuelling. The capacities of the chain

oil tank and fuel tank are carefully matched. You should

therefore always ﬁll the chain oil tank and fuel tank at the

same time. (43)

Fuel safety

• Never refuel the machine while the engine is running.

• Make sure there is plenty of ventilation when refuelling

or mixing fuel (petrol and 2-stroke oil).

• Move the machine at least 3 m from the refuelling

point before starting it.

• Never start the machine:

1 If you have spilt fuel or chain oil on the machine. Wipe

off the spillage and allow remaining fuel to evaporate.

2 If you have spilt fuel on yourself or your clothes,

change your clothes. Wash any part of your body that

has come in contact with fuel. Use soap and water.

3 If the machine is leaking fuel. Check regularly for leaks

from the fuel cap and fuel lines.

Transport and storage

• Always store the chain saw and fuel so that there is no

risk of leakages or fumes coming into contact with

sparks or naked ﬂames from electrical equipment,

electric motors, relays/switches, boilers and the like.

• Always store fuel in an approved container designed

for that purpose.

• For longer periods of storage or for transport of the

chain saw, the fuel and chain oil tanks should be

emptied. Ask where you can dispose of waste fuel and

chain oil at your local petrol station.

• The guide bar cover must always be ﬁtted to the

cutting attachment when the machine is being

transported or in storage, in order to prevent accident

contact with the sharp chain. Even a non-moving

chain can cause serious cuts to yourself or persons

you bump into with an exposed chain.

• Remove the spark plug cap from the spark plug.

Activate the chain brake.

• Secure the machine during transport.

Long-term storage

Empty the fuel/oil tanks in a well ventilated area. Store the

fuel in approved cans in a safe place. Fit the guide bar

cover. Clean the machine. See instructions under the

heading Maintenance schedule.

Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

!

WARNING! Taking the following

precautions, will lessen the risk of ﬁre:

Do not smoke and do not place any hot

objects in the vicinity of fuel.

Always stop the engine and let it cool for

a few minutes before refuelling.

When refuelling, open the fuel cap slowly

so that any excess pressure is released

gently.

Tighten the fuel cap carefully after

refuelling.

Always move the machine away from the

refuelling area and source before

starting.

!

WARNING! Fuel and fuel vapour are

highly ﬂammable. Take care when

handling fuel and chain oil. Be aware of

the risks of ﬁre, explosion and those

associated with inhalation.

!

WARNING! Never use a machine with

visible damage to the spark plug guard

and ignition cable. A risk of sparking

arises, which can cause a ﬁre.

STARTING AND STOPPING

English – 19

1155296-38 Rev.1 2012-11-19

Starting and stopping

Starting

The chain brake must be engaged when the chain saw is

started. Activate the brake by moving the front hand guard

forwards. (48)

Cold engine

Start position, 1: Set the start/stop switch in the choke

position by pulling the red control outward - upward. (44)

Air purge, 2: Press the air purge diaphragm repeatedly

until fuel ﬁlls the diaphragm (at least 6 times). The

diaphragm need not be completely ﬁlled. (44)

Grip the front handle with your left hand. Hold the chain

saw on the ground by placing your right foot through the

rear handle. (45)

Pull the starter handle, 3: Pull the starter handle with

your right hand and pull out the starter cord slowly until

you feel a resistance (as the starter pawls engage) then

pull ﬁrmly and rapidly until the engine ﬁres.

Push down the red choke control, 4: As soon as the

engine ﬁres which can be heard through a "puff" sound,

push down on the red choke control. (47)

Pull the starter handle, 5: Keep on pulling the cord

powerfully until the engine starts.

Warm engine

Start position, 1: The correct choke/start throttle setting

for warm starting is obtained by initially moving the choke

control by pulling the red control outward - upwards. (44)

Air purge, 2: Press the air purge diaphragm repeatedly

until fuel ﬁlls the diaphragm (at least 6 times). The

diaphragm need not be completely ﬁlled. (44)

Push down the red choke control, 4: This inactivates

the choke, which is not needed when starting a warm

chain saw. However the movement of the start/stop switch

will have engaged a high idle, making warm starting

easier. (47)

Pull the starter handle, 5: Grip the front handle with your

left hand. Hold the chain saw on the ground by placing

your right foot through the rear handle. (45)

Pull the starter handle with your right hand and pull out the

starter cord slowly until you feel a resistance (as the

starter pawls engage) then pull ﬁrmly and rapidly until the

engine starts.

As the chain brake is still engaged the speed of the engine

must be set to idling as soon as possible, this is achieved

by disengaging the throttle lock. Disengagement is done

by gently touching on the throttle trigger. This prevents

unnecessary wear to the clutch, clutch drum and brake

band. Allow the machine to idle a few seconds before

giving full throttle.

There is a simpliﬁed start reminder with illustrations to

describe each step on the rear edge of the saw (A). (44)

CAUTION! Do not pull the starter cord all the way out and

do not let go of the starter handle when the cord is fully

extended. This can damage the machine.

Note! Pull the front hand guard towards the front

handle. The chain brake is now disengaged. Your chain

saw is now ready for use. (38)

• Never start a chain saw unless the bar, chain and all

covers are ﬁtted correctly. See instructions under the

heading Assembly. Without a bar and chain attached

to the chain saw the clutch can come loose and cause

serious injury.

• The chain brake should be activated when starting. Se

instructions under the heading Start and stop. Do not

drop start. This method is very dangerous because

you may lose control of the saw. (48)

• Never start the machine indoors. Exhaust fumes can

be dangerous if inhaled.

• Observe your surroundings and make sure that there

is no risk of people or animals coming into contact with

the cutting equipment.

• Always hold the saw with both hands. The right hand

should be on the rear handle, and the left hand on the

front handle. All people, whether right or left handed,

should use this grip. Use a ﬁrm grip with thumbs and

ﬁngers encircling the chain saw handles.

• The chain brake is released by moving the front hand

guard marked ”PULL BACK TO RESET” back,

towards the front handle.

Stopping

Stop the engine by pushing the start/stop switch down.

(13)

CAUTION! The start/stop switch automatically returns to

run position. To avoid involuntary start up, the spark plug

cap must always be removed from the spark plug when

the machine is unsupervised. (49)

!

WARNING! Note the following before

starting:

The chain brake must be engaged when

the chain saw is started to reduce the

chance of contact with the moving chain

during starting.

Never start a chain saw unless the bar,

chain and all covers are ﬁtted correctly.

Otherwise the clutch can come loose and

cause personal injuries.

Place the machine on ﬁrm ground. Make

sure you have a secure footing and that

the chain cannot touch anything.

Keep people and animals well away from

the working area.

Never twist the starter cord around your

hand.

!

WARNING! Long term inhalation of the

engine’s exhaust fumes, chain oil mist

and dust from sawdust can represent a

health risk.

WORKING TECHNIQUES

20 – English

1155296-38 Rev.1 2012-11-19

Before use: (50)

1 Check that the chain brake works correctly and is not

damaged.

2 Check that the rear right hand guard is not damaged.

3 Check that the throttle lockout works correctly and is

not damaged.

4 Check that the stop switch works correctly and is not

damaged.

5 Check that all handles are free from oil.

6 Check that the anti vibration system works and is not

damaged.

7 Check that the mufﬂer is securely attached and not

damaged.

8 Check that all parts of the chain saw are tightened

correctly and that they are not damaged or missing.

9 Check that the chain catcher is in place and not

damaged.

10 Check the chain tension.

General working instructions

Basic safety rules

1 Look around you:

• To ensure that people, animals or other things cannot

affect your control of the machine.

• To make sure that none of the above might come

within reach of your saw or be injured by falling trees.

CAUTION! Follow the instructions above, but do not use a

chain saw in a situation where you cannot call for help in

case of an accident.

2 Do not use the machine in bad weather, such as

dense fog, heavy rain, strong wind, intense cold, etc.

Working in bad weather is tiring and often brings

added risks, such as icy ground, unpredictable felling

direction, etc.

3 Take great care when removing small branches and

avoid cutting bushes (i.e. cutting many small branches

at the same time). Small branches can be grabbed by

the chain and thrown back at you, causing serious

injury.

4 Make sure you can move and stand safely. Check the

area around you for possible obstacles (roots, rocks,

branches, ditches, etc.) in case you have to move

suddenly. Take great care when working on sloping

ground.

5 Take great care when cutting a tree that is in tension.

A tree that is in tension may spring back to its normal

position before or after being cut. If you position

yourself incorrectly or make the cut in the wrong place

the tree may hit you or the machine and cause you to

lose control. Both situations can cause serious

personal injury.

6 Before moving your chain saw switch off the engine

and lock the chain using the chain brake. Carry the

chain saw with the bar and chain pointing backwards.

Fit a guard to the bar before transporting the chain

saw or carrying it for any distance.

7 When you put the chain saw on the ground, lock the

saw chain using the chain brake and ensure you have

a constant view of the machine. Switch the engine off

before leaving your chain saw for any length of time.

General rules

1 If you understand what kickback is and how it happens

then you can reduce or eliminate the element of

surprise. By being prepared you reduce the risk.

Kickback is usually quite mild, but it can sometimes be

very sudden and violent.

2 Always hold the chain saw ﬁrmly with your right hand

on the rear handle and your left hand on the front

handle. Wrap your ﬁngers and thumbs around the

handles. You should use this grip whether you are

right-handed or left-handed. This grip minimises the

effect of kickback and lets you keep the chain saw

under control. Do not let go of the handles! (51)

3 Most kickback accidents happen during limbing. Make

sure you are standing ﬁrmly and that there is nothing

in the way that might make you trip or lose your

balance.

Lack of concentration can lead to kickback if the

kickback zone of the bar accidentally touches a

branch, nearby tree or some other object.

Have control over the workpiece. If the pieces you

intend to cut are small and light, they can jam in the

saw chain and be thrown towards you. Even if this

IMPORTANT!

This section describes basic safety rules for using a

chain saw. This information is never a substitute for

professional skills and experience. If you get into a

situation where you feel unsafe, stop and seek expert

advice. Contact your chain saw dealer, service agent or

an experienced chain saw user. Do not attempt any task

that you feel unsure of!

Before using a chain saw you must understand the

effects of kickback and how to avoid them. See

instructions under the heading How to avoid kickback.

Before using a chain saw you must understand the

difference between cutting with the top and bottom

edges of the bar. See instructions under the headings

How to avoid kickback and Machine’s safety equipment.

Wear personal protective equipment. See instructions

under the ”Personal protective equipment” heading.

!

WARNING! Sometimes chips get stuck in

the clutch cover causing the chain to

jam. Always stop the engine before

cleaning.

La page charge ...

Husqvarna 135 Manuel utilisateur

Ce manuel convient également à

Husqvarna 135 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents