Motorola 853HD Manuel utilisateur

User’s Guide

Digital Video Baby Monitor With Wi-Fi

®

Internet Viewing

Models: MBP853CONNECT, MBP853CONNECT-2,

MBP853CONNECT-3, MBP853CONNECT-4

The features described in this User’s Guide are subject to modifications without prior notice.

Welcome...

to your new Motorola Digital Video Baby Monitor!

Thank you for purchasing your new Motorola Digital Video Baby Monitor.

Now you can see and hear your baby sleeping in another room or you can

monitor your older children in their playroom.

Please retain your original dated sales receipt for your records.

For warranty service of your Motorola product, you will need to provide a

copy of your dated sales receipt to confirm warranty status. Registration is

not required for warranty coverage.

For product related questions, please call:

This User's Guide provides you with all the information you need to get the

most from your product.

Before you can use the Baby Monitor, we recommend you insert and fully

charge the battery in the Parent Unit, so that it continues to work if you

disconnect it from the power supply to carry it to another location. Please

read the Safety Instructions on page 8 before you install the units.

Got everything?

• 1 x Parent Unit

• 1 x Baby Unit (Camera)

• 1 x Power adapter for the Parent Unit

• 1 x Power adapter(s) for the Baby Unit(s)

• 1 x Rechargeable Ni-MH battery pack

In multi-camera packs, you will find one or more additional camera units

with power adapter units and battery packs.

+49 (0) 1805 938 802 in Europe

Email: motor[email protected]

Overview of the Parent Unit

1.

Display (LCD screen)

2.

Up Key

+

Normal Mode: Tilt Up

Menu Mode: Up

3.

Down Key

-

Normal Mode: Tilt Down

Menu Mode: Down

4.

Left Key

<

Normal Mode: Pan Left

Menu Mode: Left

5.

Right Key

>

Normal Mode: Pan Right

Menu Mode: Right

6.

Menu Key

M

Press to open the Menu options

7.

OK Key O

8.

Video ON/OFF Key

V

Press to turn OFF the LCD display

Press again to turn ON the LCD

display

9.

Talk Key

T

Press and hold to speak to your baby

10.

Power Adapter / Battery LED

BLUE when mains adapter power on.

RED when battery low.

11.

Unit ON/OFF LED (Green)

12.

Audio Level LED (Green, Orange,

Red, Red)

13.

Microphone

14.

Power Key

P

Press and Hold to turn the unit ON/

OFF

15.

Antenna

Lift the antenna for optimal

reception

16.

Battery cover

17.

Stand

18.

Speaker

19.

USB power adapter socket

20.

AV out / Audio out

POWER

18

15

11

14

13

16

17

19

20

6

7

8

9

2

3

4

5

10 12

1

Parent Unit menu icons

Signal Level (4 Levels)

Night Vision Mode (Screen changes to Black/White)

Tal k Mode

Battery Level Control (4 Levels)

Pan Left

Pan Right

Tilt Up

Tilt Down

Volume Level Control (8 Levels)

Zoom Level Control (1X, 2X)

Brightness Level Control (8 Levels)

Lullaby Control (5 Song Selections)

Alarm Setting (6h, 4h, 2h, Off)

Temperature Reading (HH ºC / ºF or LL ºC / ºF)

Icon & readings turn RED > 29ºC / 84ºF, and reading display

(HH ºC / ºF > 36ºC / 97 ºF)

Icon & readings turn RED < 14ºC / 57ºF, and reading display

(LL ºC / ºF < 1ºC / 34 ºF)

Camera Control (scan, view, add, delete)

View multiple cameras on screen (Picture in Picture). Available when you

have more than 1 Baby Unit (Camera).

Set Video On Timer (5 min, 30 min, 60 min)

V

Important guidelines for installing your Baby Monitor

• To use your Video Monitor Baby and Parent Units together, you must be able to establish a

radio link between them, and the range will be affected by environmental conditions.

• Any large metal object, like a refrigerator, a mirror, a filing cabinet, metallic doors or

reinforced concrete between the Baby and Parent Unit may block the radio signal.

• The signal strength may also be reduced by other solid structures, like walls, or by radio

or electrical equipment, such as TVs, computers, cordless or mobile phones,

fluorescent lights or dimmer switches.

• Use of other 2.4 GHz products, such as wireless networks (Wi-Fi

®

routers), Bluetooth

®

systems, or microwave ovens, may cause interference with this product, so keep the

Baby Monitor away at least 1m from these types of products, or turn them off if they

appear to be causing interference.

• If the signal is weak, try raising the Parent Unit Antenna, moving the Parent and/or the

Baby Unit to different positions in the room(s).

1. Light Sensor (for night mode detection) 7. Speaker

2. Camera Lens 8. Antenna

3. Infrared LEDs (for night vision) 9. Micro USB socket

4. Power / Status indicator 10. ON/OFF Switch

5. Microphone 11. Temperature Sensor

6. PAIR Button

Overview of Your Baby Unit

1

9

11

10

8

2

3

6

5

4

7

5V 1.5A

6 Table of contents

Table of contents

1. Safety Instructions..................................................................................... 8

2. Getting Started........................................................................................ 11

2.1 Baby Unit Power Supply .........................................................................11

2.2 Parent Unit Battery Installation.................................................................. 11

2.3 Parent Unit Power Supply ......................................................................... 12

2.4 Registration (Pairing) ................................................................................ 13

2.5 View Video Through TV............................................................................ 13

3. Using the Baby Monitor........................................................................... 15

3.1 Setting up .................................................................................................. 15

3.2 Pan and Tilt ................................................................................................ 15

3.3 Night Vision Mode .................................................................................... 15

3.4 Talk Mode.................................................................................................. 15

3.5 Video ON/OFF ......................................................................................... 15

3.6 Temperature Display (HH °C / °F or LL °C / °F)...................................... 15

4. Parent Unit Menu Options ...................................................................... 16

4.1 Volume ...................................................................................................... 16

4.2 Brightness.................................................................................................. 16

4.3 Lullaby ....................................................................................................... 16

4.4 Zoom ......................................................................................................... 16

4.5 Alarm ......................................................................................................... 16

4.6 Camera Control........................................................................................ 17

4.6.1 Add (pair) a camera .................................................................. 17

4.6.2 View a camera ........................................................................... 17

4.6.3 View multi-cameras on screen (Picture in Picture) .................. 17

4.6.4 Delete a camera ........................................................................ 18

4.6.5 Scan camera .............................................................................. 18

4.7 Temperature ............................................................................................. 19

4.8 Power Saving mode.................................................................................. 19

5. Wi-Fi Internet Viewing ............................................................................ 20

5.1 System Requirements............................................................................... 20

5.2 Getting started - Connecting Devices..................................................... 21

5.3 User Account and Camera Setup on Android™ Devices....................... 22

5.3.1 Power ON and Connect the Camera ...................................... 22

5.3.2 Download the Hubble App ....................................................... 22

5.3.3 Run the Hubble App on Android™ device ............................. 23

5.3.4 Add Camera to your account ................................................... 24

9. General Information ................................................................................63

8. Help.......................................................................................................... 55

7. Cleaning .................................................................................................. 54

6. Disposal of The Device (environment) ................................................... 53

5.8 Procedure for resetting the Camera ........................................................52

Working with PC/Notebook.....................................................................52

Table of contents 7

ENGLISH

5.4 User Account and Camera Setup:

Working with iPhone

®

/iPad

®

...................................................................28

5.4.1 Power ON and Connect the Camera ......................................28

5.4.2 Download the Hubble App .......................................................28

5.4.3 Run the Hubble App on your iPhone

®

/iPad

®

.........................29

5.4.4 Add the Camera to your account .............................................30

5.5 Camera Functions:

Working with devices for Android™ .......................................................34

5.5.1 Connecting the Camera to Power ...........................................34

5.5.2 Add more cameras ....................................................................34

5.5.3 Remove a Camera ....................................................................35

5.5.4 Change your Account Information ..........................................36

5.5.5 Camera settings ........................................................................37

5.5.6 General Settings ........................................................................38

5.5.7 Features of the Hubble App .....................................................39

5.6 Camera Functions:

Working with devices for iPhone

®

/iPad

®

...............................................43

5.6.1 Add more cameras ....................................................................43

5.6.2 Remove a Camera ....................................................................44

5.6.3 Change your Account Information ..........................................45

5.6.4 Camera settings ........................................................................46

5.6.5 General settings ........................................................................47

5.6.6 Hubble App Settings .................................................................48

5.6.7 Features of the Hubble App .....................................................49

5.7 Camera Functions:

8 Safety Instructions

1. Safety Instructions

WARNING:

Strangulation Hazard: Children have

STRANGLED in cords. Keep this cord

out of the reach of children (more than

3ft (1m) away). Never use extension

cords with AC Adapters. Only use the AC

Adapters provided.

Safety Instructions 9

ENGLISH

WARNING

This digital video Baby Monitor is compliant with all relevant standards

regarding electromagnetic fields and is, when handled as described in the

User's Guide, safe to use. Therefore, always read the instructions in this User's

Guide carefully before using the device.

• Adult assembly is required. Keep small parts away from children when

assembling.

• This product is not a toy. Do not allow children to play with it.

• This Baby Monitor is not a substitute for responsible adult supervision.

• Keep this User’s Guide for future reference.

• Do not place the Baby Unit or cords in the cot or within reach of the baby (the

unit and cords should be more than 1 metre away)

• Keep the cords out of reach of children.

• Do not cover the Baby Monitor with a towel or blanket.

• Never use extension cords with power adapters. Only use the power

adapters provided.

• Test this monitor and all its functions so that you are familiar with it prior to

actual use.

• Do not use the Baby Monitor near water.

Baby Unit SET UP & USE:

● Choose a location for the Baby Unit that will provide the best view of

your baby in their cot.

● Place the Baby Unit on a flat surface, such as a dresser, desk, or shelf or

mount the Unit to a wall securely using the keyhole slots on the

underside of the stand.

● NEVER place the Baby Unit or cords inside your child's cot.

● Do not place the Baby Unit or cords in the cot or within reach of the

baby (the unit and cords should be more than 1 metre away).

10 Safety Instructions

• Do not place the Baby Monitor near a heat source.

• Only use the chargers and power adapters provided. Do not use other

chargers or power adapters as this may damage the device and battery

pack.

• Only insert approved battery pack.

• Do not touch the plug contacts with sharp or metal objects.

CAUTION

Risk of explosion if battery is replaced by an unapproved battery type.

Dispose of used batteries according to their instructions.

The Unit shall be setup and used such that parts of the user’s body other than the

hands are maintained at a distance of approximately 20 cm (8 inches) or more.

Getting Started 11

ENGLISH

2. Getting Started

2.1 Baby Unit Power Supply

1. Connect the small plug of the power adapter to the Baby Unit (camera) and

the other end to a suitable mains power socket.

NOTE

Only use the enclosed power adapter (5V DC / 1500mA).

2. Slide the ON/OFF switch to the ON position. The power LED will light up

in blue.

3. Slide the ON/OFF switch to the OFF position to turn the Baby Unit off.

2.2 Parent Unit Battery Installation

1. Insert the wire tab of the rechargeable battery pack into the contact slot as

shown above and fit the battery pack into the compartment.

ON OFF

Switch to turn ON

the camera

Power adapter plug

Black

Red

Small cross head or

Flat end screw driver

12 Getting Started

2. Replace the battery cover over the compartment and gently tighten the

screw in a clockwise direction using a Small cross head or Flat end screw

drivers.

2.3 Parent Unit Power Supply

IMPORTANT

Installing the rechargeable battery pack and charging it fully before use is

recommended. This will allow the unit to operate on battery in the event of a

power failure.

1. Connect the small plug of the power adapter to the Parent Unit and the

other end to a suitable mains power socket. Only use the enclosed power

adapter (5V DC / 600mA) with micro USB plug.

2. Press and hold the

P POWER ON/OFF button for 2 seconds to turn ON

the Parent Unit.

3. Once the Baby and Parent Units are switched on, the display on the Parent

Unit will show the video captured by the Baby Unit.

4. If there is no connection or you are out of range, the video display will be

replace by a symbol and the unit will beep every 5 seconds. Move the

Parent Unit closer to the Baby Unit until the link is re-established.

5. Press and hold the

P POWER ON/OFF button, until the progress bar

finishes scrolling, to turn OFF the Parent Unit.

NOTE

The battery icon turns RED to indicate that the battery is low, and the

parent unit will beep every 15 seconds. The battery needs to be recharged; it

will take 12 hours to charge fully.

Getting Started 13

ENGLISH

When charging

1. During power OFF, and the adapter is plugged in, an adapter logo will display

on-screen and then a flashing battery logo will display for 45 sec. The Blue LED

at the top left corner will light up, indicating that the adapter is plugged in.

2. Whilst the power is ON, and the adapter is plugged in, the battery icon at the

top right corner of the screen will show that the battery is charging. The Blue

LED at the top left corner will light up to indicate that the adapter is plugged in.

2.4 Registration (Pairing)

The Baby monitor is pre-registered to your Parent Unit. You do not need to

register it again unless the Baby Unit loses its link with the Parent Unit.

To re-register your Baby Unit, or register a new Baby Unit, follow the procedure

below:

1. Press the

M button of the Parent Unit and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted, and

the

///

menu will pop up.

3. Press the UP button or DOWN button to select , and press the

O button to confirm.

4. / / / will pop up, press the UP button or DOWN button

to select the desired CAM and press the

O button to start searching for

a camera unit. The green audio level LED will flash rapidly while searching.

5. Press the

O button to confirm.

6. Press and hold the PAIR button underneath the Baby Unit until the Parent

Unit finds the camera, beeps and the video from the camera appears.

NOTE

If a particular Baby Unit was registered previously, registering this current

Baby Unit again will overwrite the old registration.

2.5 View Video Through TV

Connect a suitable AV cable into the AV OUT socket on the side of the Parent

Unit and into the AV input of the TV. Scroll to select on the Parent Unit and

press

O button to confirm, the display screen goes off. Scroll through the AV

inputs on the TV menu until the Baby monitor picture is visible. AV cable is an

optional accessory, which is to be purchased separately.

del

add

view

scan

add

cam

*1

cam

2

cam

3

cam

4

V

:<

14 Getting Started

NOTE

The Monitor's power button must be turned ON and CAM pre-selected before

connecting the AV cable. Once the AV cable is connected, the Monitor's

controls cannot be activated.

You can hear also your baby in mono mode by connecting the 3.5mm plug

wired headset to the AV OUT socket.

Using the Baby Monitor 15

ENGLISH

3. Using the Baby Monitor

3.1 Setting up

• Place the Baby Unit in a convenient location (e.g. on a table) and point the

camera lens towards the area you want to monitor.

• Adjust the angle of the Baby Unit's head by rotating the camera up, down, left

and right until you are satisfied with the image in the Parent Unit.

NOTE

Do not place the Baby Unit within the baby's reach! If there is interference with

the picture or sound, try moving the units to different locations, and ensure they

are not close to other electrical equipment.

3.2 Pan and Tilt

The camera can be remotely controlled from the Parent Unit.

1. Press the UP button or

DOWN button to tilt up or down.

2. Press the LEFT button or RIGHT button to pan left or right.

3.3 Night Vision Mode

The Baby Unit has 8 high-intensity infrared LEDs for picking up clear images in the

dark. When the built-in photo sensor on the top of the unit detects a low level of

ambient light, the LEDs will automatically activate and the screen on the Parent Unit

will display in black and white. The icon will be displayed at the top of the screen.

3.4 Talk Mode

Press and hold the

T

TALK button on the Parent Unit to talk to your baby through the

Baby Unit’s loudspeaker. The

T

icon will be displayed at the top of the LCD screen.

3.5 Video ON/OFF

Press V VIDEO ON/OFF key to turn the LCD display on or off, whilst still

leaving the audio monitor on.

3.6 Temperature Display (HH °C / °F or LL °C / °F)

The temperature reading from the temperature sensor at the back of the Baby

Unit will be displayed at the top of the LCD screen. The readings will turn RED if

the temperature goes above 29°C / 84°F or below 14°C / 57°F. The reading will

change to HH °C / °F if the temperature goes above 36°C / 97°F. The reading

will change to LL °C / °F if the temperature goes below 1°C / 34°F.

16 Parent Unit Menu Options

4. Parent Unit Menu Options

4.1 Volume

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted.

3. Press the UP button or DOWN button to select the desired volume

level from level 0 ~ 8. (The default volume level setting is level 4.)

4.2 Brightness

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted.

3. Press the UP button or DOWN button to select the desired brightness

level from level 1 ~ 8. (The default brightness level setting is level 5.)

4.3 Lullaby

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted.

3. Press the UP button or DOWN button to select the desired song

from the 5 lullabies available, or the cycle option to play all 5 songs in turn. If

an individual song is selected it will only play once. (The default setting is

lullaby OFF)

4.4 Zoom

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until

is highlighted.

3. Press the UP button or DOWN button to select the

1X

or

2X

Zoom.

(The default setting is 1X.)

4.5 Alarm

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted.

3. Press the UP button or

DOWN button to select the alarm time (

6h

,

4h

,

2h

). (The default setting is Alarm OFF.)

4. If an alarm time is selected, the Parent Unit will beep for about 45 seconds

after every 6, 4 or 2 hour period.

Parent Unit Menu Options 17

ENGLISH

4.6 Camera Control

4.6.1 Add (pair) a camera

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted, and

the

///

menu will pop up.

3. Press the UP button or DOWN button to select , and press the

OK button to confirm.

4. / / / will pop up, press the UP button or DOWN button

to select the desired CAM, and press the OK button to start searching for a

camera unit. The green audio level LED will flash rapidly while searching.

5. Press and hold the PAIR button on the underside of the Baby Unit until the

Parent Unit finds the camera, beeps and the picture from the camera

appears.

NOTE

A camera can only be registered to one Parent Unit at any one time.

4.6.2 View a camera

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted and

the

///

menu pops up.

3. Press the UP button or DOWN button to select , and press the

OK button to confirm.

4. / / / will pop up, press the UP button or DOWN button

to select the desired camera, and press the OK button to view the picture

from that camera.

TIP

Quick Method to View Cameras instead of entering into the menu bar.

Directly press OK repeatedly to select , , , ,.

4.6.3 View multi-cameras on screen (Picture in Picture)

This function is only available when you have more than 1 Baby Unit (Camera).

When the Picture in Picture function is On, you can view multiple cameras on

the screen.

del

add

view

scan

add

cam

*1

cam

2

cam

3

cam

4

del

add

view

scan

view

cam

*1

cam

2

cam

3

cam

4

cam

*1

cam

2

cam

3

cam

4

scan

18 Parent Unit Menu Options

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted.

3. Press the UP button or DOWN button to select Picture in Picture

On/Off.

4. When the Picture in Picture function is On, you can press the LEFT

button/ RIGHT button/ UP button / DOWN button to switch

between cameras.

4.6.4 Delete a camera

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted, and

the

///

menu will pop up.

3. Press the UP button or DOWN button to select , and press the

OK button to confirm.

4. / / / will pop up, press the UP button or DOWN button

to select the desired CAM, and press the OK button to delete that

registration.

Note:

You are not allowed to delete the camera if there is only one registered camera

in the system.

4.6.5 Scan camera

This function is only available when you have more than 1 Baby Unit (Camera).

1. Press the

M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted, and

the

///

menu will pop up.

3. Press the UP button or DOWN button to select , and press the

OK button to confirm.

4. The screen will then display images from different registered cameras in a

loop of / / / , changing about every 12 seconds.

TIP

Quick Method to View Cameras instead of entering into the menu bar.

Directly press OK repeatedly to select , , , , .

del

add

view

scan

del

cam

*1

cam

2

cam

3

cam

4

del

add

view

scan

cam

*1

cam

2

cam

3

cam

4

cam

*1

cam

2

cam

3

cam

4

scan

Parent Unit Menu Options 19

ENGLISH

4.7 Temperature

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until is highlighted.

3. Press the UP button or DOWN button to select °C or °F.

4.8 Power Saving mode

1. Press the M button and the menu bar will pop up.

2. Press the LEFT button or RIGHT button until

V is highlighted.

3. Press the UP button or DOWN button to select auto video off after

5 mins, 30 mins or 60 mins if not in charging.

20 Wi-Fi Internet Viewing

5. Wi-Fi Internet Viewing

5.1 System Requirements

Web Portal

• Windows

®

7

• Mac OS

®

10.7

• Chrome™ 24

• Internet Explorer

®

9

• Safari

®

6

• Java™ 7

• Firefox

®

18.0

• Adobe

®

Flash

®

Player 15.0

Android

™

System

• Version 4.2 or above

iPhone

®

/iPad

®

iOS

• Version 7.0 or above

Wi-Fi

®

requirements:

• At least 0.6 Mbps upload bandwidth per camera. Test your Internet speed at:

http://www.speedtest.net/

La page charge ...

Motorola 853HD Manuel utilisateur

Motorola 853HD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents