Peerless XHB432 Mode d'emploi

12018-05-30 #:180-9116-4 (2019-04-15)

XTREME™ HIGH BRIGHT OUTDOOR DISPLAY

User Guide

ENG

22018-05-30 #:180-9116-4 (2019-04-15)

SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS

Electrical Code

Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of

the National Electric Code that provides guidelines for proper grounding and, in particular, species

that the cable ground shall be connected to the grounding system of the facility. Outlet shall be

installed near the equipment and shall be easily accessible.

Antenna discharge unit

(NEC Section 810-20)

NEC National Electric Code

Ground clamp

Electric service

equipment

Ground clamps

Power service grounding

electrode system

(NEC Art 250 Part H)

Grounding conductors

(NEC Section 810-21)

Antenna lead-in wire

Power Source

The display must be connected to a mains socket outlet with a protective grounding connection.

The mains plug is used as the disconnect device and shall remain readily accessible.

Electrical installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/NFPA70.

An outdoor antenna should not be located near overhead electrical lines or any electrical circuits.

If an outside antenna is connected to the receiver, conrm that the antenna system is grounded to

protect against voltage surges and built up static charges. Section 810 of the National Electric Code,

ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the mast and

supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding

connectors, location of antenna discharge unit, connection to grounding electrodes and requirements

for the grounding electrode.

This display operates on 100-240 volts 50-60 Hz, AC current. Insert the power cord into a 120 volt

60 Hz outlet. Never connect the display to direct current or anything other than the specied voltage.

To prevent electric shock from the display, do not use with an extension cord, receptacle, or other

outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.

All secondary lines must be routed through grounded conduit and kept separate from AC line.

Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150

to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.

32018-05-30 #:180-9116-4 (2019-04-15)

Relevant Information

Record your display's model and serial number here for future reference. Keep this user manual in an

accessible location in the event service is required.

Note: Your display's serial number can be found on the box and underneath the rear cover plate.

Model Number ____________________________________

Serial Number ____________________________________

FCC CAUTION

To assure continued compliance and possible undesirable interference, ferrite cores may be used

when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to

other peripheral devices.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with these instructions,

may cause harmful interference to radio communications; however, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/display technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause

undesired operation.

42018-05-30 #:180-9116-4 (2019-04-15)

Read before operating equipment

Thank you for purchasing our product. Before using it, please read this user guide carefully and follow

the instructions for safe operation. Please keep this manual for future reference and always include it

when transferring or transporting this product to a dierent location.

GENERAL SAFETY PRECAUTIONS

In case of emergency such as re or electric shock caused by the product, immediately contact 911

or proper emergency police/re service agencies in your country.

To reduce the risk of electric shock or re, heed the following:

• In case of product malfunction or unusual events such as electrical burning smell, smoke, or

loss of content signals due to internal overheating, immediately turn o, unplug the electrical

cord and contact the manufacturer.

• Do NOT disassemble, modify or service product in any way other than that contained in this

instruction. Any unauthorized modications made to the product automatically void product

warranty.

• Do NOT touch antenna lines or wires, electrical cables or plugs when lightning or thunder is

present or with wet hands

• Do NOT submerge in water.

• Do NOT destroy, process, or place close to any heat source.

• Do NOT install near poisonous gas or chemically unstable atmosphere.

• Do NOT install near strong magnetic or electrical current eld.

• Do NOT install the product in unstable locations or near moving objects, constantly vibrating

equipment, or uneven surfaces.

• Do NOT leave any re source, such as candles, close to or on the product.

• Do NOT operate the product if it has been dropped or struck. Severe physical impact to the

product may cause components to fall out of place within and break.

• Do NOT bend or twist electrical cords, electrical plugs, cables, or wires with excessive force.

• Do NOT block ventilation slots or place any heavy object on the product.

• Use properly rated electrical voltage.

• Do NOT use any electrical sockets or power strips with many other devices jointly plugged

in. Use a single, directly dedicated and rated GFCI electrical outlet for the product for safe

operation.

• Do NOT move or transport with any cables (electrical, content connectivity) plugged in to the

source devices.

• Always connect the electrical plug rmly and completely. When disconnecting any cables,

always pull on the plug and not the cord.

• Always leave the power o when plugging or unplugging the electrical cords or connection

cables.

• Do not defeat the safety purpose of the polarized or grounding type electrical plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades and

a third grounding prong. The wide blade or the third prong are provided for your safety. If the

provided plug does not t into your outlet, consult an electrician for replacement of the obsolete

outlet.

• Protect the electrical cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

WARNING

52018-05-30 #:180-9116-4 (2019-04-15)

WARNING

• Never apply pressure to the exterior of the LCD screen.

• If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.

• Do NOT climb on the product.

• Do NOT install within ve feet from a body of water.

• Do NOT use if ambient air temperature exceeds the operating limits.

• Do NOT install in enclosure or recessed cavity with less than 2 inches of airow around the

display. Air inside fully encased display must be ventilated.

• The product is to be secured to building before operation.

• Product must be carried and supported by at least two persons.

• Periodically clean dust o the electrical plug to keep it clean and dry, ensuring proper and safe

operation.

• Only use attachments/accessories specied by the manufacturer.

62018-05-30 #:180-9116-4 (2019-04-15)

System Installation And Electrical Requirements ..................................................................................2

Electrical Code ...............................................................................................................................2

Power Source ................................................................................................................................2

FCC Caution ...................................................................................................................................3

FCC Statement ...............................................................................................................................3

Relevant Information .....................................................................................................................3

General Safety Precautions ...................................................................................................................4

Set Up Instructions .................................................................................................................................7

Parts List ........................................................................................................................................7

Removing Cord Cover ....................................................................................................................8

Installing Power Cord .....................................................................................................................9

Installing IR Extender .....................................................................................................................9

Installing ALS Extender ..................................................................................................................9

Connecting Cords .........................................................................................................................10

Replacing Cord Cover ..................................................................................................................12

Replacing Handle Hardware ........................................................................................................13

Connect To The Power Source .....................................................................................................13

Prepare The Display For Mounting ..............................................................................................14

Remote Control Battery Installation And Replacement ................................................................16

Operating Instructions ..........................................................................................................................17

Power On/O the Display .............................................................................................................17

Onboard Controls .........................................................................................................................17

Navigating The On-Screen Menu ................................................................................................18

Channel ...............................................................................................................................18

Picture ..................................................................................................................................18

Audio ...................................................................................................................................18

Time ....................................................................................................................................19

Setup ...................................................................................................................................19

Lock .....................................................................................................................................20

USB Functionality ........................................................................................................................22

(RS-232C) Serial Control Of The Display ....................................................................................24

Network Commands Of The Display ...........................................................................................25

Maintenance ........................................................................................................................................26

Care Of The Screen ....................................................................................................................26

Mobile Telephone Caution ...........................................................................................................26

End Of Life Directives ..................................................................................................................26

Product Specications .........................................................................................................................27

Display ..........................................................................................................................................27

Power ..........................................................................................................................................27

Environmental .............................................................................................................................27

Display Controller Features .........................................................................................................27

Mechanical ..................................................................................................................................28

Input/Output Connections ............................................................................................................28

Warranty ..............................................................................................................................................29

CONTENTS

72018-05-30 #:180-9116-4 (2019-04-15)

SET UP INSTRUCTIONS

Parts List

Description Qty

XHB432

Part #

XHB492

Part #

XHB552

Part #

Adisplay 1 180-W1663 180-W1664 180-W1665

Bremote 1 410-0049 410-0049 410-0049

CIR extender 1 600-0711 600-0711 600-0711

Dpower cord 1 410-0163-1 410-0163-1 410-0163-1

E4mm allen wrench 1 560-9646 560-9646 560-9646

FM6 x 12mm 4 560-D1734 560-D1734 560-D1734

Guser guide (not shown) 1 180-9116 180-9116 180-9116

Hmonitoring addendum (not shown) 1 180-9125 180-9125 180-9125

Itechnical support insert (not shown) 1 983-0721 983-0721 983-0721

Jaccessory insert (not shown) 1 983-0738 983-0738 983-0738

Kremote guide (not shown) 1 180-9098 180-9098 180-9098

B (1)

A (1)

remotedisplay

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

C (1)D (1)F (4)

IR extender power cord M6 x 12mm

IR

IN

E (1)

4mm allen wrench

82018-05-30 #:180-9116-4 (2019-04-15)

Removing Cord Cover

1. Remove (2) M6 low-prole hex screws and rear cover plate using 4mm allen wrench (E). Do not

disconnect lanyard.

2. Remove (6) M5 hex screws and cord cover using 4mm allen wrench (E).

A

1 2

lanyard

92018-05-30 #:180-9116-4 (2019-04-15)

Insert female end of power cord (D) into power port located inside the input compartment.

Installing Power Cord

Installing IR Extender (Optional)

Installing Ambient Light Sensor

(ALS) Extender (Optional)

IR

IN

D

C

Insert the 3.5mm end of the included 5V

IR extender into the IR Extender port on

the input panel of the display. IR extender

port may not be compatible with other 3rd

party extenders.

Insert the 3.5mm end of the ALS Extender

(ACCD-ALS sold separately) into the ALS

Extender port on the input panel of the

display. Connecting the ALS Extender

will disable the ALS that is built into the

display.

10 2018-05-30 #:180-9116-4 (2019-04-15)

___

---

___

---

S/PDIF

Optical

Audio

In

VGA

HDMI 1

Display

Port

USB 2.0

Data

Audio

Out

RS232C

LAN Mini AV

Component

Antenna or

Cable

ALS

Extender IR

Extender

HDMI 2 HDMI 3

Mini AV

12V 2500mA

USB Power

5V 2400mA

Connecting Cords

Connect source devices to appropriate display input. Make all connections prior to powering on the

display. The USB 2.0 Data port is for service and media only. For 5VDC power, use the 5VDC power

port.

1417 15 16 118 4

3 8 9 10 11 12 13 2765

1. 2.5mm DC Power Port – Provides 12 VDC @ 2.5 A for powering locally stored extenders and

source devices. 12 VDC accessory kits (ACCD-12K) are sold separately from Peerless-AV by

contacting Customer Care at 800-865-2112. Accessory DC outputs are only active when display

is on.

2. USB DC Power Port – Provides 5 VDC @ 2.4 A for powering locally stored extenders and

source devices. 5 VDC accessory kits (ACCD-05K) are sold separately from Peerless-AV by

contacting Customer Care at 800-865-2112. Accessory DC outputs are only active when display

is on.

3. RS232C DB9 Port – Allows for control of the display using RS232 commands from a connected

PC or control system. Pin Out: Pin 2 (RX), Pin 3 (TX), Pin 5 (GROUND)

4. 3.5mm IR Extender Port – Allows exibility for integration with controls systems. The IR extender

can be used to position the IR receiver in a convenient position in the event the IR receiver on

the front of the display is obscured.

5. 3.5mm Analog Audio Out Port – Provides analog stereo audio for soundbars, headphones, and

ampliers.

6. USB 2.0 Data Port – Allows content to be displayed using a USB ash drive. This feature

supports text, photo, audio and video. This port also serves as a service port for rmware

upgrades. This port should not be used for powering 5 VDC devices.

7. DisplayPort – Connects a digital source device with the display and allows for FHD video and

digital audio to be output on the display. DisplayPort is version 1.2 and is HDCP 1.3 compliant.

8. HDMI 1 (ARC) - Connects a digital source device with the display and allows for FHD video

and digital audio signal to be output to the display. HDMI 1 is HDMI version 2.0 and is HDCP

2.2 compliant. All 3 of the HDMI inputs also support consumer electronics control (CEC). CEC

allows for intelligent communication between CEC-enabled devices through the use of the HDMI

connection. HDMI 1 also supports the audio return channel (ARC) allowing audio content from

the display to be back-fed to an audio amplier using a single HDMI connection.

9. HDMI 2 - Connects a digital source device with the display and allows for FHD video and

digital audio signal to be output to the display. HDMI 2 is HDMI version 2.0 and is HDCP 2.2

compliant. All 3 of the HDMI inputs also support consumer electronics control (CEC). CEC

allows for intelligent communication between CEC-enabled devices through the use of the HDMI

connection.

10. HDMI 3 - Connects a digital source device with the display and allows for FHD video and

digital audio signal to be output to the display. All 3 of the HDMI inputs also support consumer

electronics control (CEC). CEC allows for intelligent communication between CEC-enabled

devices through the use of the HDMI connection. HDMI 3 is HDMI version 2.0 and is HDCP 2.2

compliant. HDMI 3 also supports mobile high denition link (MHL3.0) allowing MHL compatible

mobile devices to output HD content to the display, transport control and charge the connected

device.

11 2018-05-30 #:180-9116-4 (2019-04-15)

Connecting Cords

11. VGA – Connects an analog source device with the display and allows FHD video signals to be

output to the display. VGA does not support audio. When using a VGA connection the audio

output from the source device will need to be connected to the 3.5mm Audio In port on the

display.

12. 3.5mm Analog Audio In – Accepts the incoming stereo analog audio signal coming from a VGA

connected source device.

13. S/PDIF Optical Output – Outputs uncompressed digital audio to a connected soundbar or AVR

with an optical digital audio input.

14. Antenna/Cable Coaxial Input – Supports ATSC, NTSC and QAM256 signals. It can be used with

an over-the-air antenna or in a distributed coaxial network. This connection supports both analog

and digital signals.

15. 3.5mm Mini AV – Connects an analog source device with the display and allows for SD video

and analog stereo audio signals to be output to the display. This connection also supports the

audio portion of a connected component device. Requires a 3.5mm to RCA female composite

accessory dongle. Analog accessory kits (ACCD-ALG) are sold separately from Peerless-AV by

contacting Customer Care at 800-865-2112.

16. 3.5mm Mini Component – Connects an analog source device with the display and allows for

HD video and analog stereo audio signals to be output to the display. Requires a 3.5mm to

RCA female component accessory dongle for video signals. If audio is required when using the

component connection, the stereo audio signal will need to connect to the red and white female

RCA connectors on the composite accessory dongle. Analog accessory kits (ACCD-ALG) are

sold separately from Peerless-AV by contacting Customer Care at 800-865-2112.

17. LAN Port – Supports Network Control via TCP/IP (refer to Network Command section). Future

Use: Health and Wellness monitoring of the display (see Monitoring Addendum).

18. 3.5mm Ambient Light Sensor (ALS) Extender – Automatically adjusts the brightness of the

display based on ambient lighting conditions. The ALS extender overrides the built-in ambient

light sensor when it is connected allowing exibility for installations where the built-in ALS may

have shadows being cast on it by surrounding structures or vegetation. The ALS extender can

be placed in a location that is more representative of the actual ambient light conditions. ALS

Extenders (ACCD-ALS) are sold separately from Peerless-AV by contacting Customer Care at

800-865-2112.

12 2018-05-30 #:180-9116-4 (2019-04-15)

Replacing Cord Cover

1. Run power and signal cords through notches. To prevent unwanted interference, route the power

cord through the left most notch (see image 1 below).

2. Place the cord cover over the cords being careful not to pinch any of the cords. Loosely install

(6) M5 hex cap screws then tighten screws on the cord cover using 4mm allen wrench (E) until

the gasket on the cover is fully compressed to the cord gasket .

3. Replace the rear cover plate ensuring that the cords are running through the notches on the

display and not getting pinched. Fasten the (2) hex screws on the rear cover plate to secure it in

place using 4mm allen wrench (E). Ensure that rear cover plate is fully compressed to the back

of the display.

• Ensure cord bend radius does not exceed limits set by the

manufacturer.

• Ensure cords are seated properly in the cable channels to avoid

potential damage to cords when rear cover plate is installed.

• Do not remove lanyard that connects the rear cover plate to the display.

• Ensure cables exiting input compartment are routed downward when

installing display in portrait orientation. If the installation requires the

cabling to be routed upward, ensure that the cables are routed with a

drip loop.

CAUTION

Do not overtighten screws

43

power cord

1 2

notch

M5 hex cap screw

CAUTION

Failure to follow these instructions can result

in the product being damaged or destroyed,

voiding the warranty.

13 2018-05-30 #:180-9116-4 (2019-04-15)

Replacing Handle Hardware

Optional: If removing handles, replace with hardware provided.

F (4)

CAUTION

Failure to follow these instructions can result

in the product being damaged or destroyed,

voiding the warranty.

Connect To The Power Source

Connect power cord to GFCI outlet.

14 2018-05-30 #:180-9116-4 (2019-04-15)

Prepare The Display For Mounting

Install cords prior to mounting your display. Input panel may be obstructed once the display is

mounted.

A mounting solution is sold separately. Contact your Peerless-AV representative for an outdoor rated

mounting solution for your particular application.

For your safety, only install an outdoor-rated mount that is suitable for the application and supports

the weight of the display. When mounting a display outdoors, use proper environmentally rated

mounts to ensure longevity in harsh environments.

Examine the chart below to determine the mounting specications for your display:

B

F

D

Part

Mounting Hole

Pattern

Required Mounting

Screws

XHB432

XHB492

XHB552

400x200mm

400x400mm

(4) M8 screws

(25mm long)

Part A B C D E F

XHB432 15.75"

(400mm)

15.75"

(400mm)

11.87"

(302mm)

3.77"

(96mm)

4.89"

(124mm)

7.87"

(200mm)

XHB492 15.75"

(400mm)

15.75"

(400mm)

14.49"

(368mm)

5.24"

(133mm)

3.92"

(100mm)

7.87"

(200mm)

XHB552 15.75"

(400mm)

15.75"

(400mm)

17.16"

(436mm)

6.74"

(171mm)

3.92"

(100mm)

7.87"

(200mm)

SIDE VIEW

A C E

REAR VIEW

15 2018-05-30 #:180-9116-4 (2019-04-15)

Prepare The Display For Mounting

Part A B C D E F

XHB432 39.50"

(1003mm)

23.28"

(591mm)

37.06"

(941mm)

20.84"

(529mm)

42.51"

(1080mm)

0.33"

(8mm)

XHB492 44.72"

(1136mm)

26.22"

(666mm)

42.27"

(1074mm)

23.78"

(604mm)

48.50"

(1232mm)

0.33"

(8mm)

XHB552 50.07"

(1272mm)

29.23"

(742mm)

47.62"

(1210mm)

26.79"

(680mm)

54.64"

(1388mm)

0.42"

(11mm)

FRONT VIEW

BEZEL / IR DETAIL VIEW

1.51"

(38mm)

1.22"

(31mm)

1.22"

(31mm)

C

A

B D

E

F

16 2018-05-30 #:180-9116-4 (2019-04-15)

The remote control is powered by two 1.5V AAA

batteries installed at the factory.

To install or replace batteries:

1. To remove the battery module of the remote

control, remove the two screws on the end of

the battery module. Slide the battery module

out of the remote control.

2. Insert two new “AAA” size batteries into the

battery module.

3. Slide the battery module back into the remote

control and reinsert the two screws in the end

of the battery module.

Remote Control Battery Installation And Replacement

B

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

CAUTION

Incorrect usage of batteries can result in leaks

or bursting. Peerless-AV recommends the

following battery use:

• Do not mix battery brands.

• Do not combine new and old batteries. This

can shorten the battery life or cause battery

acid leaks.

• Remove dead batteries immediately to

prevent battery acid from leaking into the

battery compartment.

• Do not touch exposed battery acid as it

may injure skin.

• Remove the batteries if you do not intend

to use the remote control for a long period

of time.

• Do not expose the batteries to excessive

heat from sunlight, re or other heat

sources or batteries could explode.

• Fully tighten screws to maintain the ingress

protection rating of the remote.

17 2018-05-30 #:180-9116-4 (2019-04-15)

VOL

M

CH

VOL

M

CH

VOL

M

CH

VOL

M

CH

Power On/O The Display

Power on your display by using the remote control or the power button on the bottom, left-hand

side of the display. The display will power on but image may not appear for several seconds as it

completes its power up sequence.

OPERATING INSTRUCTIONS

Onboard Controls

Direct Mode: Allows for quick access to source selection, volume settings and channel selection.

Menu Mode: Press the Menu button to access Menu Mode and activate the On Screen Display

(OSD). For a description of OSD operation refer to the next section.

The keypad buttons are assigned as indicated in the table below.

Direct Mode Menu Mode

Channel Up Up

Channel Down Down

Menu Return

Volume Up Right/OK

Volume Down Left/OK

Input Select Input Select

On/O On/O

VOL

M

CH

Point the remote control at the IR sensor located

at the top, left-hand corner of the display when in

landscape, or the top right-hand corner when in

portrait, then press the power button.

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

LED Light TV Status

Solid O

Blinking Boot up

O On

18 2018-05-30 #:180-9116-4 (2019-04-15)

Channel

Air / Cable Choose between antenna

and cable

Auto Scan Searches for available

channels

Favorite Shows favorite channels

Show/Hide Show or hide channels

DTV Signal Displays channel info and

signal strength

Navigating The On Screen Menu

Audio

Equalizer Standard

Music

Movie

Sports

Personal

Digital Output

(Optical)

PCM / Raw / O

Surround On / O

AVC On / O

Navigate Enter Exit Return

OK

MENUEXIT

OK MENU

EXIT

OK

MENU

EXIT

OK EXIT

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

Picture

Picture Mode Theater

Personal

Standard

Dynamic

Color Temp. Normal

Warm

Personal

Cool

HDMI Mode Video Mode

PC Mode

Screen H Position

V Position

Clock

Phase

Auto

Zoom Mode 4:3

16:9

Cinema

Zoom

Point to Point

Backlight 0 - 100

DLC (Dynamic

Backlight)

On / O

Color Range Auto

0 - 255

16 - 234

3DNR O

Weak

Middle

Strong

ECO Low (25 brightness)

Middle (50 brightness)

High (75 brightness)

Personal (100 brightness)

Auto

19 2018-05-30 #:180-9116-4 (2019-04-15)

Navigate Enter Exit Return

OK

MENUEXIT

OK MENU

EXIT

OK

MENU

EXIT

OK EXIT

Navigating The On Screen Menu

Time

Sleep Timer o

5 min

10 min

15 min

30 min

60 min

90 min

120 min

180 min

240 min

Time Zone Atlantic

Eastern

Central

Mountain

Pacic

Alaska

Hawaii

Korean

Time Format 12-hour

24-hour

Auto Sync On / O

Clock Enter Current Time

Wake Up Enter desired time when

display will turn on

Setup

Menu

Languages

English

Spanish

French

Transparent

(Menu

Transparency)

0%

25%

50%

75%

100%

Closed Caption

CC Mode CC O / CC On /

CC On Mute

Restore Defaults Factory reset all options

Setup Wizard

Software Update Yes / No

CEC

CEC Control On / O

Device Auto

Power O

On / O

TV Auto

Power On

On / O

Audio Receiver On / O

Device Lists Lists connected CEC

devices

Connect (future use)

Root Menu Menu of connected souce

device

No Signal Auto

Power O

On / O / Backlight

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

20 2018-05-30 #:180-9116-4 (2019-04-15)

Navigating The On Screen Menu

Lock

System Lock

Enter Password to enter System Lock settings

Defaut Password: 0000

Change

password

Allows the password to be

changed

System Lock On / O

Input Block TV, AV, Component, DP,

HDMI 1, HDMI 2, HDMI 3,

PC, USB

US TV, MPAA

Canada Canadian English,

Canadian French

RRT Setting

Reset RRT

Unrated On /O

Hotel Mode

Enter password to enter hotel mode settings

Defaut Password: 0000

Hotel Mode On / O

Change

Password

Allows the password to be

changed

Picture Mode Standard, Dynamic,

Theater, Personal

Sound Mode Standard, Music, Movie,

Sports, Personal

Key Lock On / O

Power On

Source

TV, AV, Component, DP,

HDMI 1, HDMI 2, HDMI 3,

PC, USB

Air / Cable Air, Cable

Power On

Channel

Set channel that display

will tune to when powered

on

Power On

Volume

Set volume that display

will output when turned on

Navigate Enter Exit Return

OK

MENUEXIT

OK MENU

EXIT

OK

MENU

EXIT

OK EXIT

AUX

LAST

OK

INFO

+

EXIT

CBLDVD

MUTE

POWER

VCR SAT

SOURCE

TV

1

4

7

.

2

5

8

0

3

6

9

VOL

REW PLAY FF MENU

REC STOP PAUSE GUIDE

CH

La page charge ...

Peerless XHB432 Mode d'emploi

Ce manuel convient également à

Peerless XHB432 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents