REOLINK RLN12W 4K WiFi 6 12 Channel Security System Mode d'emploi
- Taper
- Mode d'emploi
August 2023
QSG1_A_EN
Quick Start Guide
@ReolinkTech https://reolink.com
58.03.001.0350
Apply to：
RLN12W
For USA: The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A,
U-NII 2C and U-NII-3 meets the requirements of 47 CFR FCC Part15.407(g), and the manufacturer
declares that their transmission is maintained at Band U-NII-1, U-NII 2A, U-NII 2C and U-NII-3.
For Canada: The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A, U-NII 2C
and U-NII-3 meets the 47 CFR FCC Part15.407(g) requirements, and the manufacturer states
that their transmissions remain within the U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 bands.
Pour le Canada : La stabilité de fréquence de toutes les fréquences de transmission de U-NII-1,
U-NII 2A, U-NII 2C et U-NII-3 est conforme aux exigences 47 CFR FCC Part15.407(g),
et le fabricant déclare que leurs transmissions restent dans les bandes U-NII-1, U-NII 2A, U-NII 2C
et U-NII-3.
English English1 2
What's in the Box ··················································· 2
NVR Introduction ··················································· 3
Connection Diagram ···············································4
Access the NVR via Smartphone or PC ······························6
Mount Tips for the Camera ·········································7
Troubleshooting ···················································· 8
Specication ·······················································9
Notication of Compliance ·········································9
What's in the Box
EN
Contents
NVR NVR Power
Adapter
HDMI Cable
1m Ethernet
Cable
Quick Start
Guide
USB Mouse
English English3 4
NVR Introduction
54 6 7 8 10 11
1 2 3
9
HDD LED
2
USB Port
3
Power LED
1
Reset
4
Power Input
5
USB Port
6
HDMI Port
7
LAN Port (For IPC)
11
VGA Port
8
Audio Out
9
LAN Port(For Internet)
10
Dierent states of the status LEDs:
Power LED: Solid green to indicate the NVR is powered on.
HDD LED: Flashing red to indicate the hard drive is operating properly.
Connection Diagram
1.Connect the included power adapter to the NVR and a power outlet.
2.Connect the NVR to your router with an Ethernet cable (if you hope
to use it remotely).
Next, connect the mouse to the USB port of the NVR.
3.Connect the NVR to the monitor with a VGA or HDMI cable.
NOTE: There is no VGA cable and monitor included in the package.
HDMI
VGA
NVR
Router
English English5 6
4.Follow the steps on the monitor to complete the initial setup.
NOTE: In the second step, UID is disabled by default. You’re
recommended to enable it for remote access on smartphones or
computers. Or you can set it later in “Settings > System >Info”.
5.Power on your WiFi Cameras and connect them to the LAN ports
(for IPC) on the NVR via Ethernet cables.
6.Click Sync WiFi Info to connect the cameras to the NVR’s WiFi.
7.After the sychronization succeeded, remove the Ethernet cables
and wait for a few seconds for them to be reconnected wirelessly.
installedatthedesiredlocation.
NOTE: There are no cameras included in the package.
8.Afterthewirelessconnectionissuccessful,thecameracanbe
Sync Wi-Fi info
NVR
Router
• On Smartphone
Scan to download the Reolink App.
• On PC
Download path: Go to https://reolink.com > Support > App & Client.
1. Connect the NVR to a router using the included Ethernet cable.
2.Download and launch the Reolink App or Client and follow the
instructions to access the NVR.
Access the NVR via Smartphone or PC
English English7 8
Mount Tips for the Camera
• Do not face the camera towards any light sources.
• Do not point the camera towards a glass window. Or, it may result in
poor image quality because of the window glare by infrared LEDs,
ambient lights or status lights.
• Do not place the camera in a shaded area and point it towards a
well-lit area. Or, it may result in poor image quality. To ensure best image
quality, the lighting condition for both the camera and the capture object
shall be the same.
• To ensure better image quality, it’s recommended to clean the lens with
a soft cloth from time to time.
• Make sure the power ports are not directly exposed to water or
moisture and not blocked by dirt or other elements.
• With IP waterproof ratings, the camera can work properly under
conditions like rain and snow. However, it doesn't mean the camera can
work underwater.
• Do not install the camera at places where rain and snow can hit the lens
directly.
• The camera may work in extreme cold conditions as low as -10°C.
Because when it is powered on, the camera will produce heat. You may
power on the camera indoors for a few minutes before installing it
outdoors.
Installation Tips
NOTE: Please install the cameras within the NVR’s signal range.
Troubleshooting
Solutions:
• Cover the camera’s IR LEDs to see if they light up.
• lf you have a 12V power adapter, power up the camera with the power
adapter.
Cause 1：Camera is not Powering on
Solution:
Login to the NVR, go to Settings > Channel page and click Modify to input
the correct password for the camera. lf you forget your password, please
reset your camera to reset the password to default (blank).
Solution:
GotoSettings> Channelpage, clickthechannelyouwant, andthense-
lectyour cameraforthatchannel.If all channels are already in use,
please delete the oine camera from the NVR. Then the channel this
camera was taken is free now.
Camera Not Displaying lmages on the Monitor
Cause 2：Incorrect Account Name or Password
Cause 3：Camera is not Assigned to a Channel
English English9 10
Solutions:
• Connect the camera to the NVR with an Ethernet cable. Go to Network
> Wi-Fi > Settings on the monitor to sync the NVR’s WiFi.
• Install the camera within the NVR’s signal range.
• Install antennas on the camera and the NVR.
If these won‘t work, please contact Reolink
Support https://support.reolink.com
Cause 4：No WiFi After Removing the Ethernet Cable
Specication
Operating Temperature: -10°C to 45°C
RLN12W Size: 255 x 49.5 x 222.7mm
Weight: 1.4kg, for RLN12W
NVR
Notication of Compliance
FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
ISED Compliance Statements
This marking indicates that this product should not be disposed with
other household wastes. throughout the EU. To prevent possible harm
to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources.
Correct Disposal of This Product
UKCA Declaration of Conformity
Reolink declares that this product is in compliance with Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment Safety
Regulations 2016.
Reolink declares that this device is in compliance with the essential
requirements and other relevant provisions of EMC Directive 2014/30/EU
and LVD 2014/35/EU.
Simplied EU Declaration of Conformity
WiFi Operating Frequency
OPERATING FREQUENCY :
2.4 GHzEIRP< 20dBm 5 GHzEIRP< 20dBm 5.8GHz EIRP< 14dBm
English11
To return your used device, please use the return and collection systems
or contact the retailer where the product was purchased. They can take
this product for environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink Ocial Store or a Reolink authorized reseller.
Learn more:
https://reolink.com/warranty-and-return/.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service
and Privacy Policy at reolink.com. Keep out of reach of children.
Technical Support
If you need any technical help, please visit our ocial support site and
contact our support team before returning the products,
https://support.reolink.com.
This device contains licence-exempt transmitter(s
)/receiver(s) that comply withInnovation,
Science and Economic DevelopmentCanadas
licence-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
L émetteur/récepteur exempt de licence contenu
dans le présent appareil est conforme aux CNR d
Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de
licence. L exploitation est autorisée aux deux
conditions suivantes :
(1) L' appareil ne doit pas produire de
brouillage;
(2) L' appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d' en compromettre le fonctionnement.
Radio Frequency Exposure Statement for IC
This equipment complies with IC exposure limits
set forth for an uncontrolled environment. The
device can be used in portable exposure
conditions. This equipment shall be installed and
operated with minimum distance 20cm between the
radiator & body.
Cet équipement est conforme aux limites d'
exposition IC établies pour un environnement non
contrôlé. L'appareil peut être utilisé dans des
conditions d'exposition portables. Cet équipement
doit être installé et utilisé avec une distance
minimale de 20 cm entre le radiateur et le corps.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
RF Exposure Warning Statements:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en
compromettre le fonctionnement.
Radio Frequency Exposure Statement for IC
This equipment complies with IC exposure limits set forth for an uncontrolled environment.
The device can be used in portable exposure conditions. This equipment shall be installed and operated
with minimum distance 20cm between the radiator & body.
Cet équipement est conforme aux limites d'exposition IC établies pour un environnement non contrôlé.
L'appareil peut être utilisé dans des conditions d'exposition portables. Cet équipement doit être installé et
utilisé avec une distance minimale de 20 cm entre le radiateur et le corps.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
