PNI CT60 Manuel utilisateur

Wireless thermostat/ Drahtloser Thermostat

Termostato inalámbrico/Thermostat sans ﬁl

Vezeték nélküli termosztát/Termostato senza ﬁli

Draadloze thermostaat/ Termostat bezprzewodowy

Termostat fara ﬁr PNI CT60

EN - User manual .................. p. 2

DE - Benutzerhandbuch ....... p. 18

ES - Manual de usuario .......... p. 35

FR - Manuel de l’utilisateur ... p. 52

HU - Használati utasítás ........ p. 69

IT - Manuale dell’utente ......... p. 86

NL - Handleiding .................... p. 103

PL - Instrukcja obsługi ............ p. 120

RO - Manual de utilizare ........ p. 137

2

Introduction

This thermostat starts and stops the central heating

system based on a temperature limit and a preset time

period.

Special warnings

As the product must be connected to a 230V power

supply and to a heating equipment, the installation must

be carried out only by qualiﬁed personnel, in order to

avoid irreparable damage to the product or the heating

equipment to which it is connected.

Also, the ﬁrst conﬁguration of the equipment should be

performed by qualiﬁed personnel.

3

Technical speciﬁcations

Transmitter power supply 2 x AAA batteries 15.V

Receiver power supply 230VAC, max. 10A

Frequency 868 MHz

Interval of

set temperature +5°C ~ +35°C

Interval of

displayed temperature 0°C ~ +50°C

Display Yes, backlighted

Sensor NTC 3950,

10KOhm@25°C

Accuracy ±0.1°C

Step 0.5°C

Temperature

measurement unit Only Celsius degrees

Water protection class IP30

Housing ABS with ﬁreproof

standard UL94-5

4

Installation instructions

The thermostat can be mounted in 2 ways: on the table

or on the wall with the help of the brackets included in

the package.

Description of keys and icons

Day of the week

ON/OFF

Programming

Back

Eco mode

Programmed

mode

Up/Down

MenuCentral heating ON

Time

Period

Room

temperature

5

Pairing transmitter and receiver

Pairing button

Central heating ON indicator

LED 1

LED 2

Power indicator

Note: the two units come paired from the factory. Make

the pairing procedure only if there are communication

problems.

Long press the pairing button on the receiver unit.

LED 1 ﬂashes frequently.

Turn o the transmitter unit by pressing the key.

Press and hold the MENU key on the transmitter unit

until the pairing code appears on the display (for example

FF FF 0). Immediately press the ▲ key. Another code

will ﬂash on the screen. If the pairing was successful,

the code on the screen will disappear and LED 1 (green)

6

will turn o. Turn on the transmitter unit. If the set

temperature is higher than the room temperature, the

transmitter unit will send an RF signal to the receiver

unit, which, in turn, will send a ON command to the

boiler. In this situation, LED 1 (red) will remain lit.

Set the time and day of the week

Hold down the MENU key for 3 seconds. The minute

indicator will ﬂash. Use the ▲ and ▼ keys to reach the

desired value. Brieﬂy press the MENU key to conﬁrm

and move to the time setting. The time indicator will

ﬂash. Use the ▲ and ▼ keys to reach the desired value.

Brieﬂy press the MENU key to conﬁrm and move to

the day of the week setting (1 to 7). Press the MENU

key to exit.

Operation mode setup

Brieﬂy press the MENU key to set the operation mode:

Scheduled, Manual or Holiday.

7

In Scheduled mode, the PRG icon appears on the right

side of the screen as in the image below:

In Manual mode, only the time, day and temperature

are displayed on the screen:

In Holiday mode (Economic), on the right side of the

screen appears an icon in the form of a suitcase as in the

image below:

8

Scheduled mode

Schedule by day

Brieﬂy press the MENU key to set the Scheduled

operating mode.

Long press the PRG key for 3 seconds to enter the

programming menu.

The time* and temperature* will ﬂash on the screen.

Each time you press the PRG key, the selected value will

be conﬁrmed and you will move on to the next setting.

After setting the time and the temperature for the ﬁrst

period, it automatically switches to the second period,

then to the third and fourth.

Thus will continue with the setting of the 4 periods for

each day of the week (1 - 7).

9

* Note: The time can be set from 15 to 15 minutes, and

the temperature from half to half a degree. For example,

you can set the time to 07:15 or 07:30 or 07:45 and the

temperature to 22.0°C or 22.5°C or 23.0°C.

Note: Brieﬂy press the PRG key to conﬁrm a setting. Press

the MENU key to exit.

Default settings

Period 1 2

Hour Temp. Hour Temp.

12345

(Mon-Fri) 07:00 22°C 08:30 19°C

6 (Sat) 08:00 22°C 08:30 22°C

7 (Sun) 08:00 22°C 08:30 22°C

Period 3 4

Hour Temp. Hour Temp.

12345

(Mon-Fri) 17:00 22°C 17:00 19°C

6 (Sat) 17:00 22°C 22:00 19°C

7 (Sun) 17:00 22°C 22:00 19°C

10

Note: Press the ▲or ▼key to display the set temperature

on the screen. Wait a few seconds, the screen will return to

room temperature display mode.

Functions

Key lock function

If the Child protection function has been activated

in the advanced settings menu (see page 12), the

thermostat keys will lock as soon as the screen backlight

turns o.

Press the MENU key for 5 seconds to temporarily

unlock the keys.

Open window detection (OWD)

If the function has been activated from the advanced

settings menu (see page 12), the thermostat will turn

o the heating if the room temperature drops suddenly

(default setting 2°C in 15 minutes). This sudden drop in

temperature occurs when a window or door is opened

while the boiler is operating. The OP icon appears on

the screen.

The device will return to its original operating mode after

11

30 minutes. The OP icon disappears from the screen.

By pressing any key, you will exit OWD mode.

Advanced settings

Switch o the thermostat by brieﬂy pressing the key.

Press the MENU and ▲ keys simultaneously for about

6 seconds. 01 0.3°C will appear on the screen.

Use the ▲ and ▼ keys to change the settings and the

MENU key to move to the next setting.

Menu Description Range Default

01 Internal sensor

temperature

calibration

-8°C~8°C 0°C

02 Setting the

maximum

temperature

limit

5°C

~35°C 35°C

03 Set minimum

temperature

limit

5°C

~35°C 5°C

12

05 Anti-freeze

temperature 5°C~15°C 5°C

09 Hysteresis 0.1~6°C 0.3°C

10 Screen display 0: room

temp.

1: set

temp.

0

11 Child

protection 0: keys

unlocked

1: keys

locked

0

12 Open window

detection 1: On

0: O 0

13 The time

interval in

which the

sudden drop in

temperature is

detected

2~30 min. 15 min.

13

14 Degrees lost

in the time

interval set at

menu 13

2°C

3°C

4°C

2°C

15 The time after

which the

device returns

to its original

mode of

operation

10~60

min 30 min.

17 Reset 0: No

1: Yes.

Press

for 5

seconds.

0

Software

version

14

Connection diagram

The connection of the receiver unit to a 230V power

supply and to a heating system must be performed only

by qualiﬁed personnel and only after prior consultation

of the technical documentation of the thermostat and

the heating system.

The receiver unit has a relay type control (NO Normal

Open and NC Normal Closed) without potential (non-

energized) which executes the closing of a control

circuit with a maximum current of 10A and a maximum

voltage of 250VAC/DC.

Find examples of connections with certain models of

heating system at the end of the manual.

15

Connections examples

Ariston CLAS EVO SYSTEM

Ferroli DivaCondens 24/28

16

Vaillant Ecotec Pure

Motan Max Optimus

17

Simpliﬁed EU declaration of conformity

SC ONLINESHOP SRL declares that PNI

CT60 Wireless Thermostat is in accordance with

RED Directive 2014/53/EU. The full text of the

EU Declaration of Conformity is available at the

following website:

https://www.mypni.eu/products/8001/download/

certiﬁcations

Drahtloses Thermostat

PNI CT60

Handbuch

19

Einführung

Dieses Thermostat schaltet die Heizung aufgrund

einer Temperaturgrenze und eines voreingestellten

Zeitraumes ein und aus.

Achtung

Das Produkt muss an eine Versorgungsquelle von

230V und an ein Heizungsgerät angeschlossen werden,

deshalb muss der Einbau durch Fachpersonal erfolgen,

so wird die unabänderliche Beschädigung des Produkten

und des Heizungsgerätes vermieden, diese möglichen

Schäden sind nicht in der Garantie eingeschlossen.

Für die erste Konﬁgurierung des Gerätes empfehlen wir

Ihnen Fachpersonal zu Rate zu ziehen.

20

Technische Speziﬁkationen

Versorgung Sender 2 x Batterien AAA

Versorgung Empfänger 230VAC, höchstens 10A

Frequenz 868 MHz

Eingestellter

Temperaturbereich +5°C ~ +35°C

Angezeigter

Temperaturbereich 0°C ~ +50°C

Bildschirm Ja, beleuchtet

Sensor NTC 3950,

10KOhm@25°C

Genauigkeit Messung ±0.1°C

Temperaturschritt 0.5°C

Messeinheit Temperatur Nur Celsiusgrad

Schutzklasse Wasser IP30

Gehäuse ABS mit Standard

Gegenfeuer UL94-5

La page charge ...

PNI CT60 Manuel utilisateur

PNI CT60 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents