Yamaha NS-SW200 Le manuel du propriétaire

GS

Mode d’emploi

ES

IT

SV

DE

FR

Benutzerhandbuch

Bruksanvisning

Manuale di istruzioni

Manual de instrucciones

Owner’s Manual EN

Subwoofer

Caisson de Grave

Сабвуфер

NS-SW300

NS-SW200

NL

Gebruikershandleiding

PT

Manual do Proprietário

RU

Руководство пользователя

EnglishFrançaisDeutschSvenskaItalianoEspañolNederlandsPortuguêsРусский

i En

English

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE

USE.

BE SURE TO FOLLOW THESE

INSTRUCTIONS.

The precautions listed below are to prevent risk of harm

to the user and others, as well as to prevent property

damage, and to help the user use this unit properly and

safely. Be sure to follow these instructions.

After reading this manual, be sure to keep it in a safe place where

it can be referenced at any time.

WARNING

This content indicates “risk of serious injury or death.”

If you notice any abnormality

• If any of the following abnormalities occur, immediately turn

off the power and disconnect the power plug.

– The power cord/plug is damaged.

– An unusual smell or smoke is emitted from the unit.

– Foreign material gets into the interior of the unit.

– There is a loss of sound during use.

– There is a crack or damage in the unit.

Continued use could cause electric shocks, a fire, or

malfunctions. Immediately request an inspection or repair from

the dealer where you purchased the unit or from qualified

Yamaha service personnel.

Power supply

• Do not do anything that could damage the power cord.

– Do not place it near a heater.

– Do not bend it excessively or alter it.

– Do not scratch it.

– Do not place it under a heavy object.

Using the power cord with the core of the cord exposed could

cause electric shocks or a fire.

• Do not touch the power plug or cord if there is a chance of

lightning. Failure to observe this may cause electric shocks.

• Use this unit with the power supply voltage printed on it. Failure

to connect to an appropriate AC outlet may cause a fire, electric

shocks, or malfunctions.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it. Failure to observe this may

cause a fire or electric shocks.

• When setting up the unit, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug

from the AC outlet. Even when the power switch is turned off,

as long as the power cord is not unplugged from the wall AC

outlet, the unit will not be disconnected from the power source.

• If you hear thunder or suspect approaching lightning, quickly

turn off the power switch and pull the power plug from the AC

outlet. Failure to observe this may cause a fire or malfunctions.

• If not using the unit for long periods of time, be sure to pull the

power plug from the AC outlet. Failure to observe this may

cause a fire or malfunctions.

Installation

• Always fix the speaker cable to a wall or similar. If you catch

your feet or hands on the cable, the speakers may fall or

overturn, causing malfunctions or injuries.

Do not disassemble

• Do not disassemble or modify this unit. Failure to observe this

may cause a fire, electric shocks, injury, or malfunctions.

Water warning

• Do not expose the unit to rain, use it near water or in damp or

wet conditions, or place on it any containers (such as vases,

bottles or glasses) containing liquids which might spill into any

openings or places where water may drop. A liquid such as

water getting into the unit may cause a fire, electric shocks, or

malfunctions.

• Never insert or remove an electric plug with wet hands. Do not

handle this unit with wet hands. Failure to observe this may

cause electric shocks or malfunctions.

Fire warning

• Do not place any burning items or open flames near the unit,

since they may cause a fire.

Handling

• Be careful not to drop or apply strong impact to this unit. Failure

to observe this may cause electric shocks, a fire, or

malfunctions.

CAUTION

This content indicates “risk of injury.”

Power supply

• Do not use an AC outlet where the power plug fits loosely when

inserted. Failure to observe this may cause a fire, electric

shocks, or burns.

• When disconnecting the power plug, always hold the plug itself

and not the cord. Pulling by the cord can damage it and cause

electric shocks or a fire.

• Insert the power plug firmly all the way into the AC outlet.

Using the unit when it is not plugged in sufficiently can cause

dust to accumulate on the plug, causing a fire or burns.

• Be sure to request inspections or repairs from the dealer where

you purchased the unit or from qualified Yamaha service

personnel.

• Yamaha cannot be held responsible for injury to you or

damage of the products caused by improper use or

modifications to the unit.

• This product is for ordinary homes. Do not use for applications

requiring high reliability, such as managing lives, health care

or high-value assets.

ii En

Installation

• Do not place the unit in an unstable position where it might

accidentally drop or fall over and cause injuries.

• When installing this unit, do not obstruct heat dissipation.

– Do not cover it with any cloth.

– Do not block this unit’s ventilation holes (cooling slits).

– Do not install the unit in other ways than indicated.

– Do not use the device in a confined, poorly-ventilated location

Failure to observe the above may trap heat inside the unit,

causing a fire or malfunctions. Ensure that there is adequate

space around the unit: at least 20 cm (8 in) on top, 20 cm (8 in)

on the sides, and 20 cm (8 in) on the rear.

• Do not install the unit in places where it may come into contact

with corrosive gases or salt air or places that have excessive

smoke or steam. Doing so may result in malfunction.

• Avoid being near the unit during a disaster, such as an

earthquake. Since the unit may turn over or fall and cause injury,

quickly move away from the unit and go to a safe place.

• When transporting or moving the unit always use two or more

people. Attempting to lift the unit by yourself may damage your

back, result in other injury, or cause damage to the unit itself.

• Before moving this unit, be sure to turn off the power switch

and disconnect all connection cables. Failure to observe this

may damage the cables or cause you or someone else to trip and

fall.

Hearing loss

• Do not use the unit for a long period of time at a high or

uncomfortable volume level, since this can cause permanent

hearing loss. If you experience any hearing loss or ringing in the

ears, consult a physician.

• Before connecting the unit to other devices, turn off the power

for all devices. Also, before turning the power of all devices on

or off, make sure that all volume levels are set to the minimum.

Failing to do so may result in hearing loss, electric shock, or

device damage.

• When turning on the AC power in your audio system, always

turn on the unit LAST, to avoid hearing loss and speaker

damage. When turning the power off, the unit should be turned

off FIRST for the same reason. Failure to observe the above

may cause hearing impairment or speaker damage.

Maintenance

• Remove the power plug from the AC outlet before cleaning the

unit. Failure to observe this may cause electric shocks.

Handling

• Do not touch the surface having this label. Doing

so may cause burns. The label on the device

indicates that the surface to which the label is

attached may become hot during operation.

• Do not insert your hand or fingers into the bass reflex located on

the right side of this unit. Failure to observe this may cause

injury.

• Do not insert foreign materials such as metal or paper into the

bass reflex located on the right side of this unit. Failure to

observe this may cause a fire, electric shocks, or malfunctions.

• Do not do the following:

– Stand on or sit on the equipment.

– Put heavy items on top of the equipment.

– Place the equipment in a stack.

– Apply unreasonable force to buttons, switches, input/output

terminals, etc.

Failure to observe this may cause injuries or damage to the

equipment.

• Avoid pulling the connected cables to prevent injuries or

damage to the unit by causing it to fall.

• Do not operate the unit if the sound is distorting. Prolonged use

in this condition could cause overheating and result in fire.

Notice

Indicates points that you must observe in order to

prevent product failure, damage or malfunction and data

loss.

Power supply

• If not using the unit for a long period of time, be sure to pull the

power plug from the outlet. Even if this unit is turned of by

[A] (Standby/On), a minute current is still flowing.

Installation

• Do not use this unit in the vicinity of other electronic

equipment, such as a TV, radio, or mobile phone. Failure to

observe this may cause this unit or the TV or radio to produce

noise.

• Do not use this unit in a location that is exposed to direct

sunlight that becomes extremely hot, such as near a heater, or

extremely cold, or that is subject to excessive dust or vibration.

Failure to observe this may cause the unit’s panel to become

deformed, the internal components to malfunction, or for

operation to become unstable.

Connections

• If connecting external units, be sure to thoroughly read the

manual for each unit and connect them in accordance with the

instructions. Failure to properly handle a unit in accordance

with the instructions could cause malfunctions.

Handling

• Do not place vinyl, plastic, or rubber products on this unit.

Failure to observe this may cause discoloration or deformation

in the panel of this unit.

• If the ambient temperature changes drastically (such as during

unit transportation or under rapid heating or cooling) and there

is a chance condensation may have formed in the unit, leave the

unit for several hours without turning on the power until it is

completely dry before use. Using the unit while there is

condensation can cause malfunctions.

Maintenance

• If the temperature or humidity changes drastically, water

droplets (condensation) may form on the unit surface. If water

droplets form, immediately wipe them off with a soft cloth. If

water droplets are left on the unit, they may be absorbed into the

wooden parts, causing deformation.

• When cleaning the unit, use a dry, soft cloth. Using chemicals

such as benzine or thinner, cleaning agents, or chemical

scrubbing cloths can cause discoloration or deformation.

iii En

English

Information

About functions and data included in the

unit

• Air may be blown out from the bass reflex port. This is not a

malfunction. This occurs particularly often when outputting

music with heavy bass.

About content in this manual

• This manual is for the following readers:

– the users of the unit

• This manual uses the following signal words for the important

information:

This content indicates “risk of serious injury or death.”

This content indicates “risk of injury.”

Indicates points that you must observe in order to prevent product

failure, damage or malfunction and data loss, as well as to protect

the environment.

Indicates notes on instructions, restrictions on functions, and

additional information that may be helpful.

• The illustrations in this manual are for instructional purposes

only.

(rear_en_01)

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY II .........................................................1

TWISTED FLARE PORT .............................................1

FEATURES......................................................................2

SUPPLIED ACCESSORY .............................................2

PLACEMENT .................................................................2

Subwoofer orientation ................................................2

CONTROLS AND THEIR FUNCTIONS.....................3

CONNECTIONS.............................................................5

Connecting to line output (pin jack) terminal(s)

of the amplifier ......................................................5

Connecting to speaker output terminals

of the amplifier ......................................................7

Connecting to the INPUT1/OUTPUT terminals of the

subwoofer

....................................................................9

System connections ..................................................10

Plugging the subwoofer into an AC outlet

......................10

AUTOMATIC POWER-SWITCHING FUNCTION

.........10

Setting the AUTO STANDBY switch ......................10

ADJUSTING THE BALANCE....................................11

Subwoofer frequency characteristics........................13

TROUBLESHOOTING ...............................................14

SPECIFICATIONS.......................................................15

WARNING

CAUTION

NOTICE

NOTE

Information for users on collection and disposal of

old equipment:

This symbol on the products, packaging, and/or

accompanying documents means that used

electrical and electronic products should not be

mixed with general household waste.

For proper treatment, recovery and recycling of

old products, please take them to applicable

collection points, in accordance with your

national legislation.

By disposing of these products correctly, you

will help to save valuable resources and prevent

any potential negative effects on human health

and the environment which could otherwise arise

from inappropriate waste handling.

For more information about collection and

recycling of old products, please contact your

local municipality, your waste disposal service

or the point of sale where you purchased the

items.

For business users in the European Union:

If you wish to discard electrical and electronic

equipment, please contact your dealer or supplier

for further information.

Information on Disposal in other Countries

outside the European Union:

This symbol is only valid in the European Union.

If you wish to discard these items, please contact

your local authorities or dealer and ask for the

correct method of disposal.

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the rear of

the unit. You should note this serial number in the space

provided below and retain this manual as a permanent record of

your purchase to aid identification in the event of theft.

Model No.

Serial No.

CONTENTS

1

2

1 En

In 1988, Yamaha brought to the marketplace speaker systems utilizing YST (Yamaha

Active Servo Technology) to give powerful, high quality bass reproduction. This technique

uses a direct connection between the amplifier and speaker, allowing accurate signal

transmission and precise speaker control.

As this technology uses speaker units controlled by the negative impedance drive of the

amplifier and resonance generated between the speaker cabinet volume and port, it creates

more resonant energy (the “air woofer” concept) than the standard bass reflex method. This

allows for bass reproduction from much smaller cabinets than was previously possible.

Yamaha’s newly developed Advanced YST II adds many refinements to Yamaha Active

Servo Technology, allowing better control of the forces driving the amplifier and speaker.

From the amplifier’s point of view, the speaker impedance changes depending on the sound

frequency. Yamaha developed a new circuit design combining negative-impedance and

constant-current drives, which provides a more stable performance and clear bass

reproduction, without any murkiness.

Today’s bass reflex speakers use a Helmholtz

resonator to improve their bass reproduction.

However when reproducing bass that is in the

frequency region of this Helmholtz

resonator, air moves violently in and out

through the port between the interior and

exterior of the speaker, sometimes producing

noise due to the turbulent air flow at the end

of the port.

The port and the cabinet resonate at a

frequency that is determined by their

dimensions and shape. On the other hand,

turbulence in the air flow at the end of the port contains a broad range of frequency

components that are not present in the input signal. This noise occurs because the broad

range of frequency components includes components that match the resonant frequencies

of the port and cabinet, causing strong resonance.

The Twisted Flare Port developed by Yamaha changes the way in which the port widens

toward its end, and also adds a “twist” to suppress airflow turbulence at each end of the port

and thus prevent noise from occurring.

This substantially reduces the “muddy sound” and “wind noise” that until now have been

characteristic of bass reflex speakers, allowing bass to be reproduced clearly.

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY II

High-amplitude

heavy bass sound

Port

Cabinet

Advanced impedance

Converter

Active Servo

Processing

Amplifier

Air woofer

(Helmholtz resonator)

Signals

(Inaudible) signals of ultra-low amplitude

Bass sound

(audible sound

pressure radiated

from diaphragm)

TWISTED FLARE PORT

Conventional Port

Air turbulence on both ends of the port creates noise

Air turbulence is

produced.

Turbulence is

diffused, air flow

becomes smooth.

Twisted Flare Port

2 En

English

• This subwoofer system employs Advanced Yamaha

Active Servo Technology II, which Yamaha has

developed for the production of higher quality, super-

bass sound. This super-bass sound adds a more realistic,

theater-in-the-home effect to your stereo system.

• This subwoofer can easily be added to your existing audio

system by connecting to either the speaker terminals or the

line output (pin jack) terminals of the amplifier.

• For effective use of the subwoofer, the subwoofer’s

super-bass sound should be matched to the sounds of

your front speakers. You can create the best sound

quality for various listening conditions by using the

HIGH CUT control and the PHASE switch.

• The Automatic power-switching function saves you the

trouble of pressing the STANDBY/ON button to turn the

power on and off.

• The subwoofer can be linked to a Yamaha component for

simultaneous power on/off operation.

Use the supplied system control cable to connect the

subwoofer to a Yamaha component that features a

system connector jack. When you turn on or off the

power to the connected component, the subwoofer will

also be turned on or off.

• The flared, gently twisting shape diffuses the vortex of

air generated around the edge of the port, creating a

smooth flow of air. This reduces extraneous noise not

present in the original input signal, and provides clear,

accurate low frequency reproduction.

• The subwoofer can also reproduce a bass sound that is

appropriate for the source. (NS-SW300 only)

It features a B.A.S.S. switch that enables you to select a

bass effect that is suitable for the source.

After unpacking, check

that the following

accessory is contained.

FEATURES

SUPPLIED ACCESSORY

System control cable (5 m x 1)

Since the low-end frequencies of audio signals feature long wavelengths, they are almost non-directional to human ears.

The super-bass range does not create a stereo image. Therefore, a single subwoofer may be enough to produce a high-

quality super-bass sound. However, using two subwoofers (similarly to L and R front speakers) can enhance your acoustic

experience.

Place the subwoofer as shown in fig. , or for the optimum effect. : subwoofer : front speaker

Using one subwoofer

Place the subwoofer on the outside of either the left or right

front speaker.

Placing the subwoofer in between the left and

right front speakers

If you are placing the subwoofer in between the left and

right front speakers, position it slightly at an angle toward

the wall for better effect.

Using two subwoofers

Place them on the outside of

each front speaker.

NOTE

• This unit features a magnetically shielded design. However, there is still a chance that placing it too close to a CRT-type TV set

might impair picture color. Should this happen, move this unit away from the TV set.

• If the speaker volume is very loud, furniture or window glass may resonate and the subwoofer itself may vibrate. In this case,

lower the volume level. To limit resonance, use a thick curtain or similar cloth that tends to absorb sound vibrations effectively.

Also, changing the subwoofer position may be helpful.

PLACEMENT

Subwoofer orientation

A

B

C

A

or

B

or

C

NOTE

The placement shown in the figure below is also possible.

However, if the subwoofer system is placed directly facing a wall,

the bass effect may suffer due to phase cancellation caused by

the interference between the direct and reflected sounds.

To prevent this from happening, place the

subwoofer system at an angle.

(Figures , , and )

A

B

C

There may be a case that you

cannot obtain enough super-bass

sound from the subwoofer due to

standing waves.

3 En

Check the model number of your subwoofer on the label on the rear panel.

CONTROLS AND THEIR FUNCTIONS

12

3

4

Top

A

B

56 7 8 9 <

C

D

Rear

NS-SW300

Front

C

D

A

B

67

8<5

12

3

4

Front

Rear

Top

NS-SW200

4 En

English

CONTROLS AND THEIR FUNCTIONS

1Indicator

2VOLUME control (page 11)

Adjusts the volume level. Turn the control clockwise to increase the volume, and

counterclockwise to decrease the volume.

3STANDBY/ON switch

While the POWER switch is ON, press this switch to turn on the power to the

subwoofer. The indicator will light up green. Press the switch again to turn off the

power to the subwoofer. The indicator will turn off.

4Port (page 1)

Outputs super-bass sound.

5INPUT2 (NORMAL) terminals (page 5)

Used to input line level signals from the amplifier.

6INPUT3 (LFE) terminal (page 6)

If your amplifier (or receiver) can cut off high frequencies from signals sent to the

subwoofer, connect the amplifier to the subwoofer’s INPUT3 (LFE) terminal.

The HIGH CUT control m has no effect on signals input to the INPUT 3 LFE terminal.

7AUTO STANDBY (HIGH/LOW/OFF) switch (page 10)

This switch is originally set to the OFF position. By setting this switch to the HIGH or

LOW position, the subwoofer’s automatic power-switching function operates. If you

do not need this function, leave this switch in the OFF position.

NOTE

Be sure to set the POWER switch to OFF before you set the AUTO STANDBY switch.

8PHASE switch (page 11)

This switch is to be set to the REV (reverse) position. However, depending on your speaker

system or listening conditions, there may be a case when better sound quality is obtained by

setting this switch to the NORM (normal) position. Select the best position by ear.

9B.A.S.S. (Bass Action Selector System) switch (NS-SW300 only)

(page 11)

When this switch is set to MUSIC, the bass sound in audio

software is well reproduced. When the switch is set to

MOVIE, the bass sound in video software is well reproduced.

jSYSTEM CONNECTOR jack (page 10)

Connect the supplied system control cable here. If you use the system control cable to

connect a subwoofer to a Yamaha component (that features a system connector jack),

turning on or off the power to the connected component automatically turns the

subwoofer on or off.

kOUTPUT (TO SPEAKERS) terminals (page 7)

Can be used for connecting to the main speakers. Signals at the INPUT1 terminals are

sent to these terminals.

lINPUT1 (FROM AMPLIFIER) terminals (page 7)

Used to connect the subwoofer with the speaker terminals of the amplifier.

mHIGH CUT control (page 11)

Adjusts the high frequency cut off point.

Frequencies higher than the frequency selected by this

control are all cut off (and not output).

nPOWER switch

During normal usage, set this switch to ON. If you plan not to use the subwoofer for a long

period of time, set the switch to OFF.

Green:

Red:

Off:

The subwoofer is turned on.

The Automatic power-switching function has activated, and the subwoofer

is in standby mode.

The subwoofer is turned off.

The subwoofer uses a small amount of power in standby mode.

* One graduation

of this control

represents 10 Hz.

5 En

Choose one of the following connection methods most suitable for your audio system.

Choose this method if your amplifier has line output (pin jack) terminal(s).

(page 5, 6)

Choose this method if your amplifier has no line output (pin jack)

terminals. (page 7, 8)

NOTICE

• Unplug the subwoofer and other audio/video components before making connections, and do

not plug them in until all connections are completed.

• Connecting methods and terminal names on your component (such as an amplifier or receiver)

may be different from those used in this book. Please refer to the owner’s manual that came

with your component.

• All connections must be correct, that is to say L (left) to L; R (right) to R; “+” to “+” and “–” to “–”.

Example: Connecting one subwoofer

Use a commercially-available Mono pin cable (1) or a commercially-available Audio pin cable (2) to make the connections.

• Connect the SUBWOOFER (or LOW PASS, etc.) terminal on the rear of the amplifier (or AV receiver) to the /MONO INPUT2 terminal of the subwoofer using a commercially-

available Mono pin cable (1).

Alternatively,

•

When connecting the subwoofer to the SPLIT SUBWOOFER terminals (

featuring L and R channels) on the rear panel of the amplifier, use a commercially-available Audio pin cable (2)

to connect the

/MONO INPUT2 terminal to the “L” side, and the INPUT2 terminal to the “R” side of the SPLIT SUBWOOFER terminals.

NOTE

Audio signals input from the /MONO and INPUT 2 terminals on the subwoofer will not be output from the OUTPUT (TO SPEAKERS) terminals.

CONNECTIONS

1

2

Connecting to line output (pin jack) terminal(s) of the amplifier

1

2

1 Mono pin cable

2 Audio pin cable

Subwoofer

Amplifier or

receiver

NS-SW300

1

2

1 Mono pin cable

2 Audio pin cable

Subwoofer

Amplifier or

receiver

NS-SW200

6 En

English

Example: Connecting two subwoofers

Connecting to the INPUT3 (LFE) terminal

If your amplifier (or receiver) can cut off high frequencies from signals sent to the subwoofer, connect the

amplifier to the subwoofer’s INPUT3 (LFE) terminal.

This will promote higher sound quality because the signal routing in the subwoofer is shortened by bypassing

the built-in HIGH CUT circuit.

1

1 Mono pin cable

1

Subwoofer Subwoofer

Amplifier or

receiver

NS-SW300

1 Mono pin cable

11

Subwoofer Subwoofer

Amplifier or

receiver

NS-SW200

NS-SW300 NS-SW200

7 En

°Example: Connecting the subwoofer to an amplifier that features one set of speaker output terminals

Use speaker cables to connect the speaker output terminals of the amplifier to the subwoofer’s INPUT 1 (FROM AMPLIFIER) terminals. Connect the front speakers to the subwoofer’s

OUTPUT (TO SPEAKERS) terminals. Although the subwoofer is connected between the front speakers and the amplifier, the sound volume or quality will not be affected.

Connecting one subwoofer

Connecting to speaker output terminals of the amplifier

2

Right front

speaker

Subwoofer

Amplifier or

receiver

Speaker output

terminals

Left front

speaker

NS-SW300

Right front

speaker Left front

speaker

Speaker output

terminals

Amplifier or

receiver

Subwoofer

NS-SW200

8 En

English

Connecting two subwoofers

Right front

speaker Left front

speaker

Subwoofer

Speaker output

terminals

Amplifier or

receiver

Subwoofer

NS-SW300

Right front

speaker

Left front

speaker

Subwoofer Subwoofer

Speaker output

terminals

Amplifier or

receiver

NS-SW200

°Example: Connecting the subwoofer to an amplifier featuring two sets of speaker output terminals (A and B) that can output sound signals

simultaneously

Set the amplifier so that both sets of speaker output terminals (A and B) will output sound signals simultaneously. Then, connect the front speakers to terminals A, and connect the

subwoofer to terminals B.

NOTE

If your amplifier features two sets of speaker output terminals that do NOT output sound signals simultaneously, please refer to the example for connecting an amplifier that has only one set of

speaker output terminals (see the figure on the left).

9 En

WARNING

To avoid accidents resulting from tripping over loose speaker cables, fix them to the floor.

Always fix the speaker cable to a wall or similar. If you catch your feet or hands on the cable,

the speakers may fall or overturn, causing malfunctions or injuries.

NOTICE

• Do not let the bare speaker wires touch each other, because this could damage the subwoofer

or the amplifier.

NOTE

• Make sure that the “+” and “–” polarity markings of the speaker cables are observed and set

correctly. If these cables are reversed, the sound will be unnatural and lack bass.

• If the connections are faulty, no sound will be heard from the subwoofer or the speakers. Do

not insert the insulation into the hole. Sound may not be produced.

°Before connecting

Remove the insulation at the tip of the speaker cable, then twist the core wires together so

that they will not become disarrayed and short-circuited.

Remove about 15 mm (5/8") of insulation.

Remove about 10 mm (3/8") of insulation.

°How to connect

1. Loosen the terminal’s knob, as shown in the figure.

2. Insert the bare wire.

3. Tighten the knob.

4. Test the firmness of the connection by pulling lightly

on the cable at the terminal.

1. Press and hold the terminal’s tab, as shown

in the figure.

2. Insert the bare wire.

3. Release your finger from the tab to allow it

to lock securely on the cable’s wire end.

4. Test the firmness of the connection by

pulling lightly on the cable at the terminal.

Connecting to the INPUT1/OUTPUT terminals of the subwoofer

15 mm /

10 mm

Good No Good

NS-SW300

NS-SW200

°NS-SW300

Connecting the banana plug

(U.S.A., Canada and Australia models only)

1. Tighten the terminal knob.

2. Simply insert the banana plug into the terminal.

2

1

3

Red:

positive (+)

Black:

negative (–)

NS-SW300

2

1

NS-SW200

3

12

10 En

English

If you use the included system control cable to connect a subwoofer to a Yamaha

component (that features a system connector jack such as a YSP series component or

Yamaha receiver), turning on or off the power to the connected component automatically

turns the subwoofer on or off.

Connection example

How the System Connection works

NOTE

• For this feature to be available, the POWER switch on the rear panel and the STANDBY/ON

switch on the top panel (page 3) must be set to ON.

• Powering on/off via the system connection takes priority over the Automatic power-switching

function. (While the unit is turned on, the Automatic power-switching function is enabled.)

• To modify the settings of the connected components, please refer to the owner’s manual that

came with the respective component.

After all connections are completed, plug

the subwoofer and other audio/video

components into AC outlets.

This function automatically places the subwoofer in standby mode if the subwoofer does

not detect a signal from the amplifier for a certain period of time. The subwoofer

automatically turns on as soon as it detects a signal from the amplifier.

The Automatic power-switching function works as follows when the AUTO STANDBY

(HIGH/LOW/OFF) switch is set to LOW or HIGH. (Normally, set the switch to LOW.)

How the Automatic power-switching function works

*1

When the Automatic power-switching function is enabled, the subwoofer will detect a bass signal input of

below 200Hz (such as sound effects of explosion in action movies, bass guitar or bass drum sound, etc.).

*2 This value may vary depending on the system environment. For example, it may be affected by noise

generated from other equipment.

NOTE

For this feature to be available, the POWER switch on the rear panel and the STANDBY/ON

switch on the top panel (page 3) must be set to ON.

NOTE

Be sure to set the POWER switch to OFF before you set the AUTO STANDBY switch.

LOW: The Automatic power-switching function activates at a certain level of input signal.

To enable the function, select this position.

HIGH:If the Automatic power-switching function does not work well when the AUTO

STANDBY switch is set to LOW, select this position. If the function still does not

work, slightly raise the LFE LEVEL on the amplifier.

OFF:

The Automatic power-switchingy function may unexpectedly activate due to the

system environment, for example, if the subwoofer detects noise generated from the

peripheral components. In this case, select this position to disable the Automatic power-

switching function, and manually turn the unit on or off by using the POWER switch.

NOTE

• The subwoofer uses a small amount of power in auto-standby mode.

• If you plan not to use the subwoofer for a long period of time, set the POWER switch on the

rear panel to OFF, or unplug the power cable from the AC outlet.

System connections

Turning on the power to the connected component will automatically turn on the subwoofer.

* The indicator lights green.

Turning off the power to the connected component will automatically turn off the subwoofer.

* The indicator turns off.

Plugging the subwoofer into an AC outlet

Subwoofer

Supplied system

control cable

Yamaha YSP series component or receiver

To AC outlet

AUTOMATIC POWER-SWITCHING FUNCTION

The subwoofer automatically enters standby mode if it does not receive an input signal

(*1) from the amplifier for 7 or 8 minutes (*2).

* The indicator color changes from green to red.

When the subwoofer detects an input signal (*1) from the amplifier, the subwoofer

automatically turns on. * The indicator color changes from red to green.

Setting the AUTO STANDBY switch

11 En

To achieve natural sound with an effective super-bass component, you must adjust the volume and tone balance between the subwoofer and the front speakers. Follow the procedure

described below. If your amplifier or other component connected to the system features subwoofer settings, make the appropriate settings on that component.

ADJUSTING THE BALANCE

Rear panel

NS-SW300

Front panel

Rear panel

NS-SW200

Front panel

12 En

English

ADJUSTING THE BALANCE

1. Set the VOLUME control to minimum (0).

2. Turn on the power to the component(s) connected to the subwoofer.

If the component is connected to the subwoofer’s SYSTEM CONNECTOR jack, turn

on the power to that component.

3. Make sure that the POWER switch is set to the ON position, then set the STANDBY/

ON switch to ON.

* The indicator lights green.

4. Play a source that contains low-frequency components and adjust the output level of

the front speakers using the amplifier’s volume control to the desired listening level.

(Set all tone controls to flat.)

5. Adjust the HIGH CUT control to the position where the desired response can be

obtained.

Normally, set the control to a level a little higher than the front speaker’s rated

minimum reproducible frequency*.

* The front speaker’s rated minimum reproducible frequency can be looked up in the speakers’ catalog

or owner’s manual.

* The HIGH CUT control has no effect on signals input to the INPUT 3 LFE terminal. (page 6)

6. Increase the volume gradually to adjust the volume balance between the subwoofer and

the front speakers.

Normally, set the control to a level where you can obtain a little more bass effect than

when the subwoofer is not used.

7. Set the PHASE switch to the position which yields the more natural (or preferable)

phasing.

8. Set the B.A.S.S. switch to “MOVIE” or “MUSIC” according to the played source.

(NS-SW300 only)

MOVIE:

When a movie type source is played, the low-frequency effects are enhanced to allow

listeners to enjoy a more powerful sound. (The sound will be richer and deeper.)

MUSIC:

When an ordinary music source is played, the excessive low-frequency components are

cut off to make the sound clearer. (The sound will carry less bass and reproduce the

melody line more clearly.)

NOTE

Once the volume balance between the subwoofer and the front speakers is adjusted, you can

adjust the volume of your entire sound system by using the amplifier’s volume control.

However, if you replace the front speakers, you will need to make this adjustment again.

PHASE switch

In most situations, set this switch to select the reverse mode. However, depending

on your speaker systems or listening condition, there may be a case when better

sound quality is obtained by selecting the normal mode. Select the better mode by

monitoring the sound.

13 En

The figures below show the optimum adjustment of each control and the frequency characteristics when the subwoofer is combined with a typical front speaker system.

* These diagrams do not depict actual frequency response characteristics.

Subwoofer frequency characteristics

20 50 100 200 500Hz

40

50

60

70

80

90

dB HIGH CUT 40 Hz

HIGH CUT 90 Hz

HIGH CUT 140 Hz

°When combined with 10 cm (

4"

) or 13 cm (5")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW300

PHASE

Frequency response graph*

(70 Hz) (REV)

Front

speaker

°When combined with 20 cm (8") or 25 cm (10")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW300

Frequency response graph*

PHASE

Front

speaker

(50 Hz) (REV)

NS-SW300

20 50 100 200 500Hz

40

50

60

70

80

90

dB HIGH CUT 50 Hz

HIGH CUT 100 Hz

HIGH CUT 150 Hz

°When combined with 10 cm (

4"

) or 13 cm (5")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW200

PHASE

Frequency response graph*

(70 Hz) (REV)

Front

speaker

°When combined with 20 cm (8") or 25 cm (10")

acoustic suspension, 2-way system front

speakers

20 50 100 200 500Hz

40

50

60

70

80

90

dB

NS-SW200

Frequency response graph*

PHASE

Front

speaker

(50 Hz) (REV)

NS-SW200

14 En

English

Refer to the chart below if this unit does not function properly.

If the instructions given below do not help, or if the problem you are experiencing is not listed below, turn off the power to the unit, disconnect the power cord and contact an authorized

Yamaha dealer or service center.

TROUBLESHOOTING

Problem Cause What to Do

Power is not supplied

even though the

STANDBY/ON switch

is set the ON position.

The power plug is not securely

connected.

Connect it securely.

The POWER switch is set to the

OFF position.

Set the POWER switch to the ON

position.

A system connected component is

turned off.

Turn on the system connected

component.

The unit cannot be

operated.

Electric shock (such as a lightning

strike or excessive static

electricity) or power supply

voltage drop has caused the

internal microcomputer to freeze.

Once set the POWER switch to the

OFF position and then set the

POWER switch to the ON

position.

The subwoofer does not

turn on automatically

via the system

connection.

The system control cable is not

connected properly or securely.

Connect the system control cable

properly.

The POWER switch is set to OFF. Set the POWER switch to ON.

No sound.

The volume is set to minimum. Increase the volume.

Speaker cables are not connected

securely.

Connect speaker cables securely.

Low range sound is too

soft or not heard.

Speaker cables are not connected

correctly.

Connect them correctly, that is L

(left) to L; R (right) to R; “+” to

“+” and “–” to “–”.

The PHASE switch is not set

correctly.

Set the PHASE switch to the other

position.

A source sound with little bass

frequency content is being played.

Play a source sound with bass

frequencies.

Set the HIGH CUT control to a

higher position.

The sound is influenced by

standing waves.

Relocate the subwoofer or change

its positioning angle.

No bass frequency content is

being output from the amplifier.

Check the bass output setting of the

amplifier.

The volume

automatically

decreases, or the unit

turns off.

The temperature of the unit has

abnormally increased due to the

following causes.

• The unit is used continuously

at a high volume.

• The unit is used in a location

with a high temperature.

• The unit is set up and used in a

poorly ventilated location.

• Decrease the volume. If the

problem does not improve, turn

off the unit, wait until it cools

down, and then turn it on again.

• Do not set up the unit in a

location exposed to direct

sunlight or where the

temperature becomes

extremely high (for example,

near a heater).

• Turn off the unit, and when the

temperature of the unit has

sufficiently decreased, set up

the unit in a well-ventilated

location and turn it on again.

Even though the

STANDBY/ON switch

is pressed to turn on the

unit, the indicator

simply flashes red and

does not turn on.

The protection circuit was

activated due to an internal failure.

Unplug the power cable from the

AC outlet, and then plug it in

again. If the problem does not

improve, contact an authorized

Yamaha dealer or service center.

The subwoofer does not

turn on automatically.

The POWER switch is set to the

OFF position.

Set the POWER switch to the ON

position.

The STANDBY/ON switch is set

to the STANDBY position.

Set the STANDBY/ON switch to

the ON position.

The AUTO STANDBY switch is

set to the OFF position.

Set the AUTO STANDBY switch

to the HIGH or LOW position.

The level of input signal is too

low.

Set the AUTO STANDBY switch

to the HIGH position, and increase

the output level of the amplifier.

No bass frequency content is

being output from the amplifier.

Check the bass output setting of the

amplifier.

Problem Cause What to Do

15 En

Type..........................................................Advanced Yamaha Active Servo Technology II

Driver ........................................................................................... 25 cm (10") cone woofer

Magnetic shielding type

Amplifier Output (100 Hz, 5 ohms, 10% THD) .................................................... 250 W

Frequency Response.....................................................................................20 Hz–160 Hz

Power Supply

U.S.A. and Canada models ..................................................................AC 120 V, 60 Hz

Taiwan, Brazil, and Central and South America models

..................................................................................AC 110–120/220–240 V, 50/60 Hz

Australia model .................................................................................... AC 240 V, 50 Hz

U.K., Europe, Russia, and Middle East models.................................. AC 230 V, 50 Hz

Asia and General models ........................................................AC 220–240 V, 50/60 Hz

Power Consumption................................................................................................... 80 W

Standby Power Consumption........................................................................0.3 W or less

Dimensions (W × H × D)...................350 × 366 × 420 mm (13-3/4" × 14-3/8" × 16-1/2")

Weight .....................................................................................................18.0 kg (39.7 lbs.)

Type..........................................................Advanced Yamaha Active Servo Technology II

Driver ............................................................................................. 20 cm (8") cone woofer

Magnetic shielding type

Amplifier Output (100 Hz, 5 ohms, 10% THD) .................................................... 130 W

Frequency Response.....................................................................................28 Hz–200 Hz

Power Supply

U.S.A. and Canada models ..................................................................AC 120 V, 60 Hz

Taiwan, Brazil, and Central and South America models

..................................................................................AC 110–120/220–240 V, 50/60 Hz

Australia model .................................................................................... AC 240 V, 50 Hz

U.K., Europe, Russia, and Middle East models.................................. AC 230 V, 50 Hz

Asia and General models ........................................................AC 220–240 V, 50/60 Hz

Power Consumption................................................................................................... 67 W

Standby Power Consumption........................................................................0.3 W or less

Dimensions (W × H × D)......................... 290 × 306 × 351 mm (11-3/8" × 12" × 13-7/8")

Weight .....................................................................................................11.2 kg (24.7 lbs.)

The contents of this manual apply to the latest specifications as of the publishing date.

To obtain the latest manual, access the Yamaha website then download the manual file.

The subwoofer does not

enter standby mode

automatically.

Noise generated from external

appliances etc., is activating the

subwoofer.

Move the subwoofer farther away

from such appliances, and/or

reposition the connected speaker

cables.

Set the AUTO STANDBY switch

to the HIGH or LOW position.

The AUTO STANDBY switch is

set to the OFF position.

Set the AUTO STANDBY switch

to the HIGH or LOW position.

The subwoofer enters

standby mode

unexpectedly.

The level of input signal is too

low.

Set the AUTO STANDBY switch

to the HIGH position, and increase

the output level of the amplifier.

The subwoofer turns on

unexpectedly.

Noise generated from external

appliances etc., is activating the

subwoofer.

Move the subwoofer farther away

from such appliances, and/or

reposition the connected speaker

cables.

If the AUTO STANDBY switch is

set to HIGH, set it to LOW.

Alternatively, set the AUTO

STANDBY switch to the OFF

position.

An object has fallen

into the port.

Do not try to remove the object.

Attempting to remove the object

may cause a malfunction.

Contact an authorized Yamaha

dealer or service center.

Problem Cause What to Do SPECIFICATIONS

NS-SW300

NS-SW200

La page est en cours de chargement...

Yamaha NS-SW200 Le manuel du propriétaire

Ce manuel convient également à

Yamaha NS-SW200 Le manuel du propriétaire

dans d''autres langues

Documents connexes