Hikvision UD08889B-A Mode d'emploi

Marque: Hikvision

Modèle: UD08889B-A

Taper: Mode d'emploi

Ce manuel convient également à

C1X0

134 5 6

Appearance

UD08889B-A

Name Descripon

IR Light

LED

Indicator

Auto light source for night vision. The light is

behind the an-reﬂecon panel. You can see

the light when it is on.

RESET/WPS WPS: Set Wi-Fi connecon via WPS (Wi-Fi

Protected Setup) funcon.

RESET: Hold down the buon for 4 seconds

when the camera is running.

Memory

Card Slot

For micro SD card. If a memory card is used,

video ﬁles will be stored in the memory card.

You would need to inialize it via the

Hik-Connect app.

Steady red: The camera is starng up.

Flashing blue: The camera is on and ready for

the Wi-Fi connecon.

Steady blue: The camera is running properly.

Flashing red: Network excepon.

Network Mini Cube Camera

Quick Start Guide

Regulatory Informaon

FCC Informaon

Please take aenon that changes or modiﬁcaon not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protecon against harmful interference in a residenal installaon. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instrucons, may cause harmful interference to radio

communicaons. However, there is no guarantee that interference will not occur in a

parcular installaon. If this equipment does cause harmful interference to radio or television

recepon, which can be determined by turning the equipment oﬀ and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separaon between the equipment and receiver.

—Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver

is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minimum distance 20cm between the

radiator and your body.

FCC Condions

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two

condions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operaon.

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE"

and comply therefore with the applicable harmonized European standards listed

under the EMC Direcve 2014/30/EU, the RoHS Direcve 2011/65/EU, Radio

Equipment Direcve 2014/53/EU.

2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed

of as unsorted municipal waste in the European Union. For proper recycling, return

this product to your local supplier upon the purchase of equivalent new equipment,

or dispose of it at designated collecon points. For more informaon see:

www.recyclethis.info.

2006/66/EC (baery direcve): This product contains a baery that cannot be

disposed of as unsorted municipal waste in the European Union. See the product

documentaon for speciﬁc baery informaon. The baery is marked with this

symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the baery to your supplier or to a designated

collecon point. For more informaon see: www.recyclethis.info.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radioexempts de licence. L'exploitaon est autorisée aux deux condions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est suscepble d'en compromere le fonconnement.

Under Industry Canada regulaons, this radio transmier may only operate using an antenna

of a type and maximum (or lesser) gain approved for the transmier by Industry Canada. To

reduce potenal radio interference to other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that

necessary for successful communicaon.

Conformément à la réglementaon d'Industrie Canada, le présent émeeur radio peut

fonconner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour

l'émeeur par Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intenon des autres ulisateurs, il faut choisir le type d'antenne et son gain

de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité

nécessaire à l'établissement d'une communicaon sasfaisante.

This equipment should be installed and operated with a minimum distance 20cm between the

radiator and your body.

Cet équipement doit être installé et ulisé à une distance minimale de 20 cm entre le radiateur

et votre corps.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

This device complies with Industry Canada licence-exempt RSS standard(s). Operaon is

subject to the following two condions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operaon of the device.

Safety Instrucon

These instrucons are intended to ensure that a user can use the product correctly to avoid

danger or property loss.

The precauon measure is divided into “Warnings” and “Cauons”

Warnings: Serious injury or death may occur if any of the warnings are neglected.

Cauons: Injury or equipment damage may occur if any of the cauons are neglected.

Warnings: Follow these

safeguards to prevent serious

injury or death.

Cauons: Follow these

precauons to prevent potenal

injury or material damage.

Warnings

● Proper conﬁguraon of all passwords and other security sengs is the responsibility of the

installer and/or end-user.

● In the use of the product, you must be in strict compliance with the electrical safety

regulaons of the naon and region. Please refer to technical speciﬁcaons for detailed

informaon.

● Do not connect several devices to one power adapter as adapter overload may cause

over-heang or a ﬁre hazard.

● Please make sure that the plug is ﬁrmly connected to the power socket. When the product

is mounted on wall or ceiling, the device shall be ﬁrmly ﬁxed.

● If smoke, odor, or noise rise from the device, turn oﬀ the power at once and unplug the

power cable, and contact the service center.

● Make sure the power supply voltage is correct before using the camera.

● Do not drop the camera or subject it to physical shock.

● Do not touch sensor modules with ﬁngers. If cleaning is necessary, use a clean cloth with a

bit of ethanol and wipe it gently. If the camera will not be used for an extended period,

replace the lens cap to protect the sensor from dirt.

● Do not aim the camera at the sun or extra bright places. Blooming or smearing may occur

(which is not a malfuncon), and aﬀect the sensor’s endurance at the same me.

● The sensor may be burned out by a laser beam, so when any laser equipment is in use,

make sure that the surface of sensor will not be exposed to the laser beam.

● Do not place the camera in extremely hot, cold (the operang temperature shall be -10°C

to +40°C), dusty, or damp locaons, and do not expose it to high electromagnec radiaon.

● To avoid heat accumulaon, ensure that there is good venlaon to the device.

● Keep the camera away from liquids.

● While in delivery, pack the camera in its original, or equivalent, packing, packing materials.

Or packing of the same texture.

● Regular part replacement: a few parts (e.g. electrolyc capacitor) of the equipment shall be

replaced regularly according to their average endurance. The average me varies because of

diﬀerences between operang environments and usage history, so regular checking is

recommended for all users. Please contact your dealer for more details.

● Improper use or replacement of the baery may result in hazard of explosion. Replace with

the same or equivalent type only. Dispose of used baeries according to the instrucons

provided by the baery manufacturer.

● If the product does not work properly, please contact your dealer or the nearest service

center. Never aempt to disassemble the camera yourself. (We shall not assume any

responsibility for problems caused by unauthorized repair or maintenance.)

Cauons

Name Descripon

Power Input

IR Light

Lens

MIC

LED Indicator

Micro USB interface for the power supply

(5V ). Plug the power cable into the power

input interface to power on the camera.

Power

Input

Memory

Card Slot

Speaker

RESET/WPS

Quick Start Guide

Any and all informaon, including, among others, wordings, pictures, graphs are the

properes of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinaer

referred to be “Hikvision”). This user manual (hereinaer referred to be “the Manual”) cannot

be reproduced, changed, translated, or distributed, parally or wholly, by any means, without

the prior wrien permission of Hikvision. Unless otherwise spulated, Hikvision does not make

any warranes, guarantees or representaons, express or implied, regarding to the Manual.

About this Manual

The Manual includes instrucons for using and managing the product. Pictures, charts,

images and all other informaon hereinaer are for descripon and explanaon only. The

informaon contained in the Manual is subject to change, without noce, due to ﬁrmware

updates or other reasons. Please ﬁnd the latest version in the company website

(hp://www.hi-watch.eu/).

Visit the company website (hp://www.hi-watch.eu/) to get the manuals, client soware, and

developing tools.

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the properes of Hikvision in

various jurisdicons. Other trademarks and logos menoned below are the properes of

their respecve owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH

ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND

ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A

PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL

HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY

SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG

OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF

DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF

HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE

WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR

ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER

ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;

HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR

JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE

CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS

PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE

LATER PREVAILS.

7 8 9 11

Add the Camera to Your Hik-Connect Account

1Install memory card (oponal).

Insert the memory card into the card slot on the

side of the camera, as shown below.

Line up and wedge the lower edge of the

camera base with the mounng base and then

push the camera to the mounng base to

secure it.

Rotate the camera body to adjust the panning

posion.

With Hik-Connect service, you can realize some certain

funcons of this product (including, but not limited to,

live view, and remote playback), which depend on the

Internet and telecom value-added services.

2Install the camera.

Installaon Operaons

Step 1

Power on the Camera

Connect the camera to the power adapter with the

Micro USB cable, and then plug the power adapter into

the power outlet. When the blue light ﬂashes, the

camera is powered on. You can set the Wi-Fi

connecon.

Micro USB Cable

Power Outlet

Hik-Connect

Launch the Hik-Connect app and you can get the live

view of the connected devices.

Live View

- Check the memory card status by tapping on the

Storage Status in the Device Sengs interface.

- If the memory card status displays as Uninialized, tap

to inialize it. The status will then change to Normal.

You can then start recording any event triggered video

in the camera such as moon detecon.

Recording

Launch the Hik-Connect app, tap a connected device and

tap Gallery buon to play back.

Playback

Launch the Hik-Connect app and tap Message to see the

alarm messages.

Alarm Noﬁcaon

Paste the mounng template onto the

installaon surface.

Fix the mounng base to the installaon

posion according to the holes on the

mounng template.

Pull and push the camera body to adjust it to the

desired lng posion.

Adjust the surveillance angle.

70°

25°

Hik-Connect Setup

- Connect your mobile device to Wi-Fi.

- Download and install the Hik-Connect app by searching the

“Hik-Connect” in App Store or Google PlayTM.

- Launch the app and register for a Hik-Connect user

account.

Step 3

- Connect your mobile phone to a Wi-Fi (5G Wi-Fi is not

supported yet).

- Log into the Hik-Connect app.

- In the Home page, tap “+” on the upper-right corner to

add a camera.

- Scan the QR code on the boom of the camera or on the

Quick Start Guide cover.

- Tap Connect to a Network buon in the pop-up interface.

- Choose Wireless Connecon to set the Wi-Fi connecon.

- Input the Wi-Fi password that your mobile phone has

connected to, and tap Next to start the Wi-Fi connecon.

(Locate the camera within 3 meters from the router.)

- Tap Add buon in the next interface to ﬁnish adding.

Step 2

360°

0504151080627

Use of the product is subject to your registraon with

Hik-Connect and your agreement to the Terms of

Service found at

Start the adding process only when the indicator ﬂashes

blue.

Hikvision UD08889B-A Mode d'emploi

Marque: Hikvision

Modèle: UD08889B-A

Taper: Mode d'emploi

Ce manuel convient également à

C1X0

Télécharger le PDF

rapport

dans d''autres langues

English: Hikvision UD08889B-A User guide

Hikvision UD08889B-A Mode d'emploi

Ce manuel convient également à

Hikvision UD08889B-A Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents