Chief K0W100BXI2TB Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
K0P100 K0W100
K0W100BXI2 K0W100BXI2TB
Pitch/Pivot Mount Series
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
K0 Series
K0 Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system. The wall to which the mount
is being attached may have a maximum drywall thickness of
5/8” (1.6cm).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the K0 Series Monitor Arm up to
(and including) the display does not exceed the weight limits
in the table below. Use with products heavier than the
maximum weight indicated may result in collapse of the
mount and its accessories causing possible injury.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS!--
MODEL Max Weight
K0P100 40 lbs (18.14 kg)
K0W100 40 lbs (18.14 kg)
K0W100BXI2 2 lbs (0.9 kg)
K0W100BXI2TB 2 lbs (0.9 kg)
Installation Instructions K0 Series
3
DIMENSIONS
K0P100
5.29
134.5
3.08
78.3
TILT RANGE
75 UP
10 DOWN
2.75
69.9
1.97
50.1
3.05
77.4
1.50" - 1.90" OD
[38.1 - 50.8]
7.58
192.5
INTERFACE
ROTATION
RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100 M4
75 X 75 M4
4.91
124.7
TILT RANGE
75
UP
10
DOWN
3.35
85.0
1.97
50.1
INTERFACE
ROTATION
RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75
3.22
81.7
1.36
34.4
K0W100
K0 Series Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions K0 Series
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/16” (included)
1/8” (included)
5/32” (included with K0P Series only)
A (1)
[monitor arm]
(K0P100)
B (4)
M4x14mm C (4)
M4x25mm D (4)
M10x5.3x10
included with K0W Series (wall mount) only!
E (1)
[wall bracket]
F (2)
1/4 x 2 1/2” G (2)
1/4”
3/16” 1/8”
P (1) Q (1)
included with K0P Series (pole mount) only!
H (1)
[pole clamp] 5/32”
J (4)
1/4-20 x 1 1/2” K (4)
1/4-20 x 1" L (1)
or A (1)
[monitor arm]
(K0W100)
P (1)
[iPad® interface - iPad versions only!
I2B Interface + I/M
or
I2TB Interface + I/M
+
+
M (1)
#10-32 x 3/8”
N (1)
M4 x 4mm
K0 Series Installation Instructions
6
Assembly And Installation
Figure 1
(F) x 2 (E)
(G) x 2
3
4
5
set screw
6
side view
Connecting K0W Series (wall mount) to Wall
1. Determine mounting location on wall.
2. Use a stud finder to locate 2" x 4" wood stud.
3. Use wall bracket (E) to mark and drill two 1/8 x 2 1/2” holes
in wall at desired mounting location. (See Figure 1)
4. Use two 1/4-2 1/2” hex head lag screws (F) and two 1/4”
washers (G) to install wall bracket (E) onto wall. (See
Figure 1)
IMPORTANT ! : Over tightening screws (F) may cause
bracket to compress into soft wall surface resulting in
difficult mount installation or improper engaging of set
screw in Step 6.
5. Hang monitor arm (A) over wall bracket (E). (See Figure 1)
6. Secure monitor arm to wall bracket (E) by tightening set
screw. Ensure set screw engages back side of wall bracket
(E) to properly secure mount. (See Figure 1)
Connecting K0P Series to Pole
1. Determine approximate location for mount keeping in mind
display size, extension, height adjustment requirements.
2. Place mount (A) against pole with clamp (H) on opposite
side of pole. (See Figure 2)
Figure 2
3. Using 5/32” hex key (M) and appropriate length screws,
loosely attach K0P assembly to pole clamp (H). If installing
to 1 1/2” NPT pipe, use 1/4-20 x 1 1/2” button head cap
screws (J). If installing to 1 1/2” diameter pipe, use 1/4-20 x
1" button head cap screws (K). (See Figure 2)
4. Position mount at desired height and orientation.
5. Equally tighten screws against mount and the pole clamp.
3
(J or K) x 4
(H)
K0P assembly
Installation Instructions K0 Series
7
Display Installation
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the K0 Series Monitor Arm up to
(and including) the display does not exceed the weight limits
in the table below. Use with products heavier than the
maximum weight indicated may result in collapse of the
mount and its accessories causing possible injury.
NOTE: For K0W100BXI2 mounts, refer to FSBI2B installation
instructions to install iPad® to mounting arm.
1. Remove quick release faceplate from mount by pulling
quick release lever and sliding faceplate off mount. (See
Figure 3)
Figure 3
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! See
Display Removal section for details.
2. Carefully place display face down on protective surface.
3. Connect faceplate to display
For flush mounting hole installation:
• Using Phillips screwdriver, carefully install four
M4x14mm screws (B) through corresponding
holes on faceplate and into the mounting holes on
the display. (See Figure 4)
Figure 4
For recessed mounting hole installation:
• Place four spacers (D) on top of mounting holes
on back of display. (See Figure 5)
• Using Phillips screwdriver, carefully install four
M4x25mm screws (C) through corresponding
holes on faceplate, spacers (D) and into the
mounting holes on the display. (See Figure 5)
Figure 5
MODEL Max Weight
K0P100 40 lbs (18.14 kg)
K0W100 40 lbs (18.14 kg)
K0W100BXI2 2 lbs (0.9 kg)
K0W100BXI2TB 2 lbs (0.9 kg)
quick release lever
1
1
(for flush mounting holes)
(B) x 4
quick release
faceplate
3
(for recessed mounting holes)
(C) x 4
(D) x 4
quick release
faceplate
3
K0 Series Installation Instructions
8
4. Position display with faceplate attached above mount. (See
Figure 6)
5. Slide faceplate onto mounting head until quick release tab
clicks into place. (See Figure 6)
Figure 6
Adjustments
Pitch Adjustment (non-array models)
1. Adjust pitch to desired tilt position. (See Figure 7)
2. Adjust pitch tension screw to change the adjustment
tension. (See Figure 7)
Pivot Adjustment (non-array models)
3. Adjust pivot position as desired. (See Figure 7)
4. Use 3/16” hex key (Q) to adjust pivot point tension screws
to change pivot adjustment tension. (See Figure 7)
Figure 7
Rotational Adjustment
NOTE: (Optional) Rotational adjustment may be locked by
installing rotational locking screw (M) into back of
faceplate. (See Figure 8)
Figure 8
5. The monitor may be adjusted 90 degrees in either direction
in order to provide a portrait view of the monitor. (See Figure
7)
6. Use 3/16” hex key (P) to adjust rotational adjustment screw
to adjust rotational tension. (See Figure 7)
Display Removal
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! (See
Figure 9)
1. Make sure display is in the upright position.
2. Remove quick release faceplate from mount by pulling
quick release lever and sliding faceplate off mount. (See
Figure 9)
Figure 9
5
pitch
pivot point
tension
tension
5
13
Rotational tension
6
(M)
quick release tab
2
Installation Instructions K0 Series
9
Display Removal Security Screw
NOTE: In order to prevent display from being easily removed
from mount using the quick release lever, install
M4x4mm security screw (N) into lower hole on back of
faceplate. (See Figure 10)
Figure 10
(N) (N)
K0 Series Installation Instructions
10
Installation Instructions K0 Series
11
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
K0 Series Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002756 Rev00
2016 Milestone AV Technologies
www.milestone.com
11/16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Chief K0W100BXI2TB Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Chief K0W100S Mode d'emploi
-
-
-
-
-
-
Chief PSS2000 Guide d'installation
-
Chief PDC2306 Guide d'installation
-
-