Bercomac 700280-1 Manuel utilisateur
- Catégorie
- Tracteur
- Taper
- Manuel utilisateur
Ce manuel convient également à
1
B
BERCO
Subframe & Drive Mechanism
for
JOHN DEERE LT SERIES
Tractors
CAUTION:
READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE
OPERATING YOUR EQUIPMENT
106571_EN M-09
* ASSEMBLY * REPAIR PARTS
* OPERATION * MAINTENANCE
*106571*
OWNER’S MANUAL
Model Number
700279-4
700280-1
2
LIMITED WARRANTY
Bercomac Limitée
92, Fortin North, Adstock, Quebec, Canada, G0N 1S0
Conditions and Products Covered:
BERCOMAC guarantees any part of the product or accessory
manufactured by BERCOMAC and found in the reasonable
judgment of BERCOMAC to be defective in material and or
workmanship will be repaired or replaced by an authorized
dealer without charge up to our maximum labor rates and pre-
established times. For replacement parts onl
y standard ground
freight services are covered. This warranty extends to the
original retail purchaser only and is not transferable to any
subsequent purchasers. This warranty applies to the products
bought and used in North America.
Warranty Period
(from date of the original retail purchase)
Residential use: 1 year
Semi-commercial, professional or rental use: 90 days
Exceptions Noted Below; the following items are guaranteed
by the original manufacturer and have their own warranty,
conditions and limited time:
Tire Chains: 90 days
Engines: Will vary as per the manufacturer
Please refer to the engine manufacturer’s warranty
statement included with the unit. BERCOMAC is not
authorized to handle warranty adjustments on engines.
Items and Conditions NOT Covered:
This warranty does not cover the following:
Pick-up or delivery charges or in-home services fees.
Any damage or deterioration of the unit, parts and or finish
of these due to normal use, wear and tear, or exposure.
Cost of regular use o
r maintenance service or parts, such as
gas, oil, lubricants, tune-up parts, and adjustments.
g
Any part or accessory which has been altered, modified,
misused, neglected, accidentally damaged or not properly
installed, maintained, stored or repaired not in
accordance
with the instructions in the owner’s manual.
Repair due to normal wear and or any wear items such as
shear pins, bolts, belts, etc.
Expedited freight fee services for replacement parts.
Shear bolts and shear pins are to be considered as a
preventive measure not as an assured protection, any
damages resulting from the lack of shear bolts breakage are
not covered.
Damages due to product being installed on a vehicle other
than stipulated in owner’s manual.
NOTE: All warranty work must be performed
by an authorized
dealer using original (manufacturer) replacement parts.
Owner’s Responsibilities:
BERCOMAC’s defective equipment or part must be returned
to an authorized dealer within the warranty period for repairs.
In the event that defective merchandise must be returned to
manufacturer for repairs, freight fees ar
e prepaid and a written
authorization from BERCOMAC must be obtained by dealer
prior to the shipment. This warranty extends only to
equipment operated under normal conditions. To validate a
warranty claim, it is the user’s responsibility to maintain and
service the unit as specified in the owner’s manual or to have
the unit serviced at their dealer at their expense.
General Conditions:
The sole liability of BERCOMAC with respect to this warranty
shall be strictly and exclusively repair and replacement
as
mentioned herein. BERCOMAC shall not have any liability for
any other costs, loss or damage, including but not limited to,
any incidental or consequential loss or damage.
Taking advantage of the warranty does not in any way extend
the length or renewal of the warranty.
In particular, without being limited to, BERCOMAC shall have
no liability or responsibility for:
Travel time, overtime, after hours time or other
extraordinary repair charges or relating to repairs and or
replacements outside of normal business hours.
Rental of like or similar replacement equipment during the
period of any, repair or replacement work.
Any communicating or travel charges.
Loss or damage to person or property other than that
covered by the terms of this warranty.
Any clai
ms for lost revenue, lost profit or any similar costs
as a result of damage or repair.
Attorney’s fees.
BERCOMAC’s responsibility in respect to claims is limited to
making the required repairs or replacement without charge up
to our maximum labor rates and pre-
established times and no
claim of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any product or accessory.
In no event recovery of any kind be greater than the amount of
the purchase price of the product sold.
This warranty gives you specific legal rights.
You may also
have other rights, which vary from state to state.
NOTE: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify
any product previously manufactured.
Instructions for Obtaining Warranty Services:
Contact dealer where equipment was purchased or any other BERCO service dealer to arrange
service at their dealership.
Requests for
warranty claims must be carried out through the same distribution network used to purchase the product.
.
Don't forget to bring your proof
of purchase (sales receipt) to the BERCOMAC dealer.
1
TABLE OF CONTENTS
INTRODUCTION ...................................................................................................................................................... 2
SAFETY PRECAUTIONS ........................................................................................................................................ 3
ASSEMBLY
Step 1: Subframe Installation ..................................................................................................................... 5
Step 2: Drive Mechanism Installation ........................................................................................................ 8
Step 3: Snowblower Installation ................................................................................................................ 10
Rotary Broom Installation ............................................................................................................. 12
Utility Blade Installation ................................................................................................................. 14
MAINTENANCE & DISMOUNTING
Maintenance ............................................................................................................................................... 15
Drive Mechanism Dismounting .................................................................................................................. 15
Belt Replacement ....................................................................................................................................... 15
End of Season Storage .............................................................................................................................. 15
PARTS BREAKDOWN AND LISTS
Subframe ..................................................................................................................................................... 16
Drive Mechanism ........................................................................................................................................ 18
TORQUE SPECIFICATION TABLE ....................................................................................................................... 20
ATTACHMENTS ....................................................................................................................................................... 21
TROUBLESHOOTING
See attachment owner’s manual for this section. (Snowblower, Utility Blade, Rotary Broom)
PAGE
2
INTRODUCTION
TO THE PURCHASER
This new accessory was carefully designed to give years of dependable service. This manual has been provided to
assist in the safe operation and servicing of your attachment.
NOTE:
All photographs and illustrations
in the manual may not necessarily depict the actual models or attachment, but
are intended for reference only and are based on the latest product information available at the time of publication.
Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to
use. Carefully read, understand and follow these recommendations and insist that they be followed by those who will
use this attachment.
THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAG
E IN THIS
MANUAL THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH.
DANGER, WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF
HAZARD. HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.
DANGER:
Signals an extreme hazard
that will cause serious injury or death if recommended precautions
are not followed.
WARNING:
Signals a hazard that may cause serious injury or death if the recommended precautions are
not followed.
CAUTION:
Signals a hazard that may cause minor or mod
erate injury if the recommended precautions are
not followed.
Record your attachment serial number and purchase date in the section reserved below (there is no serial number on
the subframe). Your dealer requires this information to give you prompt, efficient service when ordering replacement
parts. Use only genuine parts when replacements are required.
If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer
for warranty service.
This manual should be kept for future reference.
Please check if you have received all the parts for your kit with the list of the
bag and the list of the box.
SERIAL NUMBER : ___________________________
(IF APPLICABLE)
MODEL NUMBER: ___________________________
PURCHASE DATE : ___________________________
3
SAFETY PRECAUTIONS
Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle
and accessory.
This accessory is capabl
e of amputating hands and feet and throwing objects. Failure to observe the
following safety instructions could result in serious injury. All operators, no matter how experienced they may be,
should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal
obligation to instruct all operators in safe operation of the accessory.
GLOSSARY:
In this manual, right and left sides are determined by
sitting on the seat of the vehicle facing forward.
In this manual, "accessories" means attachments
(snowblower, rotary broom, blade etc.) that you install
on the vehicle (lawn tractors, A.T.V. s etc).
TRAINING:
This symbol, "Safety Alert Symbol", is used
throughout this manual and on the
accessory’s safety labels to warn of the
possibility of serious injury. Please take
special ca
re in reading and understanding
the safety precautions before operating the
vehicle and accessory.
1.
Read this owner's manual carefully. Be thoroughly
familiar with the controls and proper use of the
vehicle and accessory
. Know how to stop the unit
and disengage the controls quickly.
2.
Never allow children to operate the vehicle nor the
accessory. Never allow adults to operate the vehicle
nor the accessory without proper instructions.
3.
No one should operate the vehicle nor the
accessory while intoxi
cated or while taking
medication that impairs the senses or reactions.
4.
Keep the area of operation clear of all people,
particularly small children and pets.
PREPARATION:
1.
Thoroughly inspect the area where the accessory
is to be used and remove doo
r mats, all foreign
objects and the like.
2.
For motorized accessories,
disengage all clutches
and shift into neutral before starting engine.
3.
Do not operate the accessory without wearing
adequate winter outer garments.
Avoid loose fitting
clothing that can get caught in moving parts.
Wear
footwear that will improve footing on slippery
surfaces.
4. Handle fuel with care, it is highly flammable.
a) Use approved fuel container.
b)
Never add fuel to a running engine or hot engine.
c)
Fill fuel tank outdoors with extreme care. Never fill
fuel tank indoors.
d) Never fill containers inside a ve
hicle, or on a
truck or a trailer bed with a plastic liner. Always
place containers on the ground, away from your
vehicle, before filling.
e) When practical, remove gas-
powered
equipment from the truck or trailer and refuel it
on the ground. If this is not
possible, then refuel
such equipment on a trailer with a portable
container, rather than from a gasoline
dispenser nozzle.
f)
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times, until
refueling is complete. Do not u
se a nozzle lock-
open device.
g)
Replace fuel cap securely and wipe up spilled
fuel.
h)
If fuel is spilled on clothing, change clothing
immediately.
5.
Never attempt to make any adjustments while the
engine (motor) is running (except when specifically
recommended by manufacturer).
6.
Let the vehicle and accessory adjust to outdoor
temperatures before using.
7.
Never use an accessory without proper guards,
plates, or other safety protective devices in place
8.
Always make sure to wear the appropriate safety
equipment required (glasses, muffs, mask…)
for
each type of product. See operation section.
9.
Always make sure of having safe traction on the
vehicle by using the recommended accessories
(chains, A.T.V. tracks, counterweights…)
. See
operation section.
10.
Al
ways make sure the all components are correctly
installed. (driveline securely attached and locked at
both ends, belts properly installed…)
11.
Always handle the winch cable with thick leather
gloves.
12
.
Never modify the accessory or any part without
the written consent from the manufacturer.
4
OPERATION:
1.
Do not put hands or feet near, under or inside rotating
parts.
2.
Exercise extreme caution when operating on or
crossing gravel drives, walks or roads. Stay alert for
hidden hazards or traffic.
Do not carry passengers.
3.
After str
iking a foreign object, stop the engine (motor),
disconnect the wire from the spark plug(s) and keep
wire away to prevent accidental starting. Thoroughly
inspect the accessory for any damage and repair
damage before restarting and using the accessory.
4.
If the unit should start to vibrate abnormally, stop the
engine (motor) and check immediately for the
cause. Vibration is generally a warning of trouble.
5.
Take all possible precautions when leaving the
vehicle unattended. Disengage the power take
-off,
l
ower the attachment, place the transmission into
neutral, set the parking brake, stop the engine and
remove the contact key.
6.
Do not run the engine indoors, except when starting
the engine and for transporting in or out of the
building. Do not operate o
r let motor run in a storage
area without ventilation because gas contains
carbon monoxide which is odorless, colorless and
can cause death.
7.
Never use the accessories
across the face of
slopes, go from top to bottom. Exercise extreme
caution when using
equipment on slopes. Do not
attempt to clear a steep slope.
8.
Never tolerate bystanders in the working zone.
Never use an accessory in the direction of
bystanders, it might throw gravel or debris that can
hurt people or damage property.
9.
Never operat
e the accessory at high transport
speeds on slippery surfaces. Use care when
backing up.
10
. Do not carry passengers.
11
.
Disengage power to the accessory when it is
transported or not in use.
12
.
Never operate the accessory without good visibility
or light.
13
.
Keep the accessory away from heat sources or
flames.
14.
Never handle the winch cable or hook while in
tension.
MAINTENANCE AND STORAGE
1.
When cl
eaning, repairing or inspecting the vehicle
and accessory, make certain that all moving parts
have stopped. For gasoline engine, d
isconnect wire
from the spark plug(s) and keep wire away to
prevent accidental starting.
2.
Check all the bolts and components
at frequent
intervals to make sure that they are properly
tightened.
3.
Never store a motorized accessory with fuel in the
fuel tank inside a building where ignition sources are
present such as hot water and space heaters,
clothes dryers, and the like.
Allow the engine to cool
before storing in any enclosure.
4.
Always refer to the owner’s manual when you store
the accessory and vehicle for a prolonged or an
unspecified length of time.
5.
Maintain or replace safety and instruction labels, as
necessary.
6 For winter accessories, (if applicable), let the engine
run for a few minutes after clean snow in order to
prevent the rotary parts from freezing.
7.
Inspect the vehicle’s and accessory’s air filter (if
applicable)
every day. Clean it or replace it as
necessary
. Change the oil more often when working
in dusty conditions. See the vehicle’s and
accessory's owner’s manual.
THIS SYMBOL MEANS
DANGER !
BECOME ALERT !
YOUR SAFETY IS INVOLVED !
SAFETY PRECAUTIONS
5
ASSEMBLY
IMPORTANT: TORQUE ALL BOLTS ACCORDING
TO TORQUE SPECIFICATION TABLE (SEE TABLE
OF CONTENTS) WHEN STATED: TIGHTEN
FIRMLY. REFER TO PARTS BREAKDOWN
SECTION FOR PARTS IDENTIFICATION.
NOTE: You can install this subframe with or without
the mower on tractor. However, on certain models
the lift height of the mower deck will be reduced.
However, the mower must be removed in order to
install the drive mechanism.
Remove the bolts (items 1 & 2) from each side of the
frame.
Disconnect wire from safety switch (item 4).
Remove the original belt guide from tractor (only if you
install the drive mechanism) and replace it with the one
(item 3) supplied with this kit as shown (the U-shaped
rod towards the front). DOES NOT APPLY TO THE
LT190 MODEL. Use the same bolt that you removed
from tractor and a M6 x 10 supplied with the drive
mechanism #700280.
NOTE: You must reinstall the original belt guide when
the mower deck is reinstalled.
Install the front supports (item 1) with four 5/16 x 1’’ hex
bolts (item 2) and flange nuts on each side.
The right front support has an extra hole for the exhaust.
Do not tighten yet.
For the LT190 Models:
Install the front supports with two bolts from the tractor,
two 5/16 x1’’ hex bolts and two flange nuts included with
this kit.
Install the left rear support (item 1) inside the front
support (item 2) with a 3/4’’ Ø pin (item 3).
Secure the rear end with a 5/16 x 1’’ hex bolt (item 4)
and flange nut.
Do not tighten yet.
STEP 1
SUBFRAME INSTALLATION:
Change original belt guide
Install front supports
Install left rear support
INSTALLING THE REFLECTORS
IMPORTANT: When operating the tractor with the
front mounted attachment, install the two red-colored
adhesive reflectors on the rear vertical surface of the
tractor’s fender.
6
ASSEMBLY
Slide the nylon bushing (item 1) flange first, down the
lift arm (item 2) to the fork (item 5).
Slide the right rear support (item 3) down the lift arm,
and onto the nylon bushing.
Install the handgrip (item 4) on the lift arm.
Install the right rear support assembly with the arm lift
(items 1 & 2) inside the front support (item 3).
Secure the rear end with a 5/16 x 1’’ hex bolt (item 4)
and flange nut.
Install the pivot support (item 5) between the front
supports with a 3/4’’ Ø pin (item 6).
Secure with two 3 mm hair pins.
Tighten all bolts securely and reconnect the safety
switch.
Install support on lift arm
Install rear support and pivot support
7
Install support on lift arm
Install the push bar (item 1) by inserting it in the sleeve
(item 2) welded on the pivot support (item 3).
Install the other end in the fork (item 4) with a pin (item
5) the head toward the outside and with a 2.5 mm hair
pin (item 6).
Install the handle support (item 1) on the left rear
support (item 2) with two 5/16 x 3/4’’ hex bolts (item 3)
and secure with flange nuts (item 4).
Install the plastic grommet (item 5) on the handle
support (item 1).
INSTALLATION OF THE SUPPORTS FOR THE
BERCO CAB:(all models) (if required).
This subframe includes the front supports to be able to
install the Berco cab.
The left support for the cab (item 6) is welded to the
handle support (item 1).
Install the right support for the cab (item 7) on the right
rear support (item 8) with two 5/16 x 3/4’’ hex bolts (item
9) and two flange nuts (item 10).
Use the 5/16 x 1/2’’ square head socket set screws
(item 11) to secure the cab’s front rod supports included
with cab.
Install push bar
Install the right support for cab
Install handle support
ASSEMBLY
8
ASSEMBLY
STEP 2
DRIVE MECHANISM INSTALLATION:
NOTE: Remove the mower deck to install the drive
mechanism. Make sure to remember where the end
of the clutch rod is connected to the tractor, because
you must reconnect the rod in the same place when
you install the drive mechanism or mower.
Remove the P.T.O. clutch rod (item 1) from the
mower.
For the LT 166 model:
Insert the pin (item 2) in the hole on the tension bar
(item 3) and in the hole (the farthest one from the
edge) on the tension link (item 4).
Secure with a flat washer (item 5) and a 2.5 mm. hair
pin (item 6).
For the LT 155 model:
Insert the pin (item 2) in the hole on the tension bar
(item 3) and in the hole (the closest one to the edge)
on the tension link (item 4).
Secure with a flat washer (item 5) and a 2.5 mm. hair
pin (item 6).
For tractors with a Freedom mower:
Remove the tension link (item 1) of the drive
mechanism and reassemble upside down (the bent
section must be on top). Secure the tension link (in
the hole farthest to the bended part) in the tension bar
(item 2) with a 3/8 x 1" hex bolt (item 3) and nylon
insert lock nut.
Do not tighten the bolts in order to allow the clutch
mechanism to move freely.
Install the mower clutch rod (item 4) with the pin in the
hole located on the top of the tension link (item 1).
Secure with a flat washer (item 5) and a 2.5 mm hair
pin (item 6).
For the LT 190 model:
To be able to install the drive mechanism, you must
remove the tension link.
Turn the tension bar (item 1) to the left towards the
outside. Hook the spring (item 2) in the hole of the
tension bar.
Stretch the spring to the other end of the idler arm
(item 3).
Make sure the idler arm moves freely.
Install clutch rod
Install clutch rod
Install spring
9
ASSEMBLY
Install the drive mechanism under the tractor by
hooking the slotted part on the tractor’s lift
mechanism crossbar (item 1).
Attach the front end to the rear support (item 2) with
two pins (item 3), the heads towards the inside.
Secure with a 2.5 mm. hair pin (item 4) on each side.
To make it easier to install the belt on the motor
pulley, remove the belt from the drive mechanism
pulley. Insert it around the motor pulley and put it
back on the drive mechanism pulley.
Install the clutch rod to the tractor’s manual clutch
lever mechanism the same way it was installed on the
mower.
Secure with a 2.5 mm hair pin.
NOTE: Check to make sure the drive mechanism
works well.
If the attachments do not stop rapidly when the
drive mechanism is disengaged, readjust the
clutch rod.
Check to be sure the belt does not touch the belt
guides at any time when the P.T.O. clutch is
engaged.
Install drive mechanism
10
ASSEMBLY
STEP 3
SNOWBLOWER INSTALLATION:
Refer to Snowblower owner’s manual, parts breakdown
section for parts identification.
WARNING
FOR YOUR SECURITY:
Read the Snowblower’s owner's manual for safe-
ty precautions and rules.
Follow the assembly and operation instructions.
Attach the snowblower to the subframe as shown.
Make sure the snowblower is pushed in until locked
into place by the springs (item 3).
Turn the handle (item 1) towards the back and install
the chain (item 2) on the hook (item 4).
Turn the handle towards the front to apply tension on
the spring.
Remove belt guard.
Install the belt around the pulleys as shown.
Install the belt on the drive mechanism pulley (item 5)
under the tractor.
Apply tension on the belt by pulling up the belt tension
arm.
Reinstall the belt guard.
NOTE: See belt replacement instructions in the
maintenance section of the snowblower owner’s
manual.
CAUTION
The belt tension arm is spring loaded & needs to be
held firmly while displacing to prevent injury.
CAUTION
Never use the snowblower without the belt guard.
Install snowblower
Install V-belt and belt guard
Item 1: Snowblower pulley
Item 2: Tractor engine pulley
Item 3: V pulley L.H.
Item 4: Flat pulley R.H.
Item 5: Drive mechanism pulley
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
11
ASSEMBLY
VERIFY BELT ROUTING:
-Lower the snowblower to the ground and let it run for
a few seconds under supervision.
-Disengage the snowblower and stop the engine.
-Remove the belt guard.
-Check the belts to make sure they are well inserted
on the pulleys and have not flipped on their sides in
the pulleys and that they do not touch the belt
guides.
-Reinstall the belt guard.
Insert the handgrip (item 1) on the handle (item 2).
Insert the handle (item 2) through the support (item 3)
as shown.
Insert the handle (item 2) in the rotation worm (item 5)
and secure with a 2.5 mm. hair pin (item 4).
VERIFY SKID SHOE ADJUSTMENT:
Level Paved Surface: Adjust skid shoes to obtain 3/16"
to 1/4" clearance between cutting edge and surface.
Uneven or Gravel Surface: Adjust skid shoes to obtain
1/2" to 5/8" clearance between cutting edge and
surface.
VERIFY TIRE PRESSURE:
Tire pressure must be even on both sides of tractor
according to the vehicle’s owner’s manual.
Install handle
Adjust skid shoes
12
ASSEMBLY
ROTARY BROOM INSTALLATION:
Refer to Rotary Broom owner’s manual, parts
breakdown section for parts identification.
WARNING
FOR YOUR SECURITY:
Read the Rotary Broom owner's manual for safe-
ty precautions and rules.
Follow the assembly and operation instructions.
Attach the rotary broom to the subframe as shown.
Make sure the rotary broom is pushed in until locked
into place by the springs (item 1).
Install the belt on the drive mechanism pulley (item 1)
as shown.
NOTE: See belt replacement instructions in the
maintenance section of the rotary broom owner’s
manual.
CAUTION
Never use the Rotary Broom without the belt
guard.
VERIFY BELT ROUTING:
-Lower the rotary broom to the ground and let it run
for a few seconds under supervision.
-Disengage the rotary broom and stop the engine.
-Check the belts to make sure they are well inserted
on the pulleys and have not flipped on their sides in
the pulleys and that they do not touch the belt
guides.
Attach rotary broom to subframe
Item 1: Drive mechanism pulley
Item 2: Rotary broom pulley Install belt
WARNING
TO PREVENT INJURIES:
Stop the motor.
Apply parking brake.
Remove the ignition key.
Disconnect the wire from the spark plug(s) and
keep away from spark plug(s) to prevent accidental
starting.
13
ASSEMBLY
Insert handgrip on the handle.
Insert the handle (item 1) through the support (item 2)
as shown.
Install the handle on the control rod (item 3) as shown
and secure with a 2.5 mm. hair pin (item 4.
VERIFY TIRE PRESSURE:
Level Paved Surface: Adjust skid shoes to obtain 3/16"
to 1/4" clearance between cutting edge and surface.
Uneven or Gravel Surface: Adjust skid shoes to obtain
1/2" to 5/8" clearance between cutting edge and
surface.
Install handle
14
ASSEMBLY
UTILITY BLADE INSTALLATION:
Refer to Utility Blade owner’s manual, parts
breakdown section for parts identification.
WARNING
FOR YOUR SECURITY:
Read the Utility Blade owner's manual for safety
precautions and rules.
Follow the assembly and operation instructions.
Attach the blade to the subframe as shown.
Make sure the blade is pushed in until locked into
place by the springs (item 1).
Insert the handgrip on the handle.
Insert the handle (item 1) through the support (item 2)
as shown.
Install the handle on the control rod (item 3) as shown
and secure with a 2.5 mm hair pin (item 4).
VERIFY TIRE PRESSURE:
Level Paved Surface: Adjust skid shoes to obtain 3/16" to
1/4" clearance between cutting edge and surface.
Uneven or Gravel Surface: Adjust skid shoes to obtain
1/2" to 5/8" clearance between cutting edge and surface.
Attach Utility Blade to subframe
Install handle
15
MAINTENANCE & DISMOUNTING
MAINTENANCE
a) Check mounting bolts at frequent intervals for
proper tightness to be sure equipment is in safe
working condition.
b) Apply oil at all pivot points.
DRIVE MECHANISM DISMOUNTING
SEE ATTACHMENT OWNER'S MANUAL
(SNOWBLOWER, BROOM AND BLADE) FOR
DISMOUNTING INSTRUCTIONS.
a) Dismount the attachment.
b) Remove the rear counterweight when you remove
the front attachment.
c) Dismount the drive mechanism by disconnecting
the clutch rod and by removing the pins in front.
Carefully lower to the ground. Detach the V-belt
from engine pulley.
d) You may leave the subframe on tractor all year long
or remove it if preferred.
e) Reinstall mower if needed.
BELT REPLACEMENT
Drive Mechanism Belt:
Before proceeding with this step, notice carefully how
the belt guide is installed to avoid damage to the belt.
When re-installing, remove the bolt which retains the
tension pulley and the belt guide. Replace the belt
and re-install the tension pulley and belt guide. Before
tightening make sure the belt guide does not touch
the belt at any time. Re-install the drive mechanism.
END OF SEASON STORAGE
a) Clean and paint all parts from which paint has worn.
b) Apply oil at all pivot points.
c) Inspect and replace all defective parts before using
again.
16
PARTS BREAKDOWN
Subframe 700279-4
17
Ref.
Réf. English description Description française Qty.
Qté. Part #
Pièce #
1 Right rear support Support arrière droit 1 103472
2 Left rear support Support arrière gauche 1 102984
3 Left front support Support avant gauche 1 102985
4 Lift arm Bras de relevage 1 102986
5 Handle support Support de manivelle 1 102987
6 Push bar Barre de poussée 1 102988
7 Pin Goupille 1 102989
8 Pivot support Support de pivot 1 102981
9 Handgrip Poignée de plastique 1 102025
10 Right spring lock Ressort de barrure droit 1 102209
11 Left spring lock Ressort de barrure gauche 1 102208
12 Handgrip Poignée 2 102248
13 Spring bracket Fixation du ressort 2 102210
14 Hair pin 3mm Goupille à ressort 3mm 2 102617
15 Pin Goupille 1 102772
16 Hair pin 2.5mm Goupille à ressort 2.5mm 1 102013
17 Hex. bolt 5/16" n.c. x 1" Boulon hex. 5/16" n.c. x 1" 12 O/L
18 Flange nut 5/16" n.c. Écrou à bride 5/16" n.c. 16 O/L
19 Plastic grommet Oeillet de plastique 1 102063
20 Hex. bolt 5/16" n.c. x 3/4" Boulon hex. 5/16" n.c. x 3/4" 4 O/L
21 Right front support Support avant droit 1 103022
22 Nylon bushing Coussinet en nylon 1 103087
23 Cab support Support de cabine 1 103895
24 Square head set screw 5/16" n.c. x 1/2" Vis à pression à tête carrée 5/16" n.c. x 1/2" 2 O/L
25 Reflector (Pack of 2) Réflecteur (Ensemble de 2) 1 106108
PARTS LIST
Subframe 700279-4
O/L = Obtain locally
18
PARTS BREAKDOWN
Drive mechanism 700280-1
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Bercomac 700280-1 Manuel utilisateur
- Catégorie
- Tracteur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Bercomac 700280-1 User manual
Documents connexes
-
Bercomac 700279-3 Le manuel du propriétaire
-
-
-
-
-
-
-
-
-