Sony STR-DA3300ES Mode d'emploi

E:\STR-DA3300ES_UC\3209648115\3209648115STRDA3300ESUC\00COV-

STRDA3300ESUC\010BCO.fm

masterpage: Left

STR-DA3300ES

3-209-648-11(5)

Sony Corporation Printed in Malaysia

010BCO.fm Page 1 Wednesday, May 30, 2007 2:30 PM

E:\STR-DA3300ES_UC\3209648115\3209648115STRDA3300ESUC\00COV-

STRDA3300ESUC\010COV.fm

masterpage: Right

STR-DA3300ES

3-209-648-11(5)

Multi Channel

AV Receiver

Operating Instructions ________________________

Mode d’emploi ______________________________

Owner’s Record

The model and serial numbers are located on the rear of the unit. Record the

serial number in the space provided below. Refer to them whenever you call

upon your Sony dealer regarding this product.

Model No.

Serial No.

STR-DA3300ES

FR

GB

010COV.fm Page 1 Wednesday, May 30, 2007 2:30 PM

2

GB

To reduce the risk of fire or electric

shock, do not expose this apparatus to

rain or moisture.

Do not install the appliance in a confined space, such

as a bookcase or built-in cabinet.

To prevent fire or shock hazard, do not place objects

filled with liquids, such as vases, on the apparatus.

Install this system so that the power cord can be

unplugged from the wall socket immediately in the

event of trouble.

Batteries or batteries installed apparatus shall not be

exposed to excessive heat such as sunshine, fire or

the like.

Don’t throw away battery with

general house waste; dispose of it

correctly as chemical waste.

For customers in the United

States

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

WARNING

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used

in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment

and receiver.

– Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

You are cautioned that any changes or modification

not expressly approved in this manual could void

your authority to operate this equipment.

Note to CATV system installer:

This reminder is provided to call CATV system

installer’s attention to Article 820-40 of the NEC

that provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building,

as close to the point of cable entry as practical.

WARNING

3

GB

About This Manual

• The instructions in this manual are for model

STR-DA3300ES. Check your model number by

looking at the lower right corner of the front panel.

• The instructions in this manual describe the

controls on the supplied remote. You can also use

the controls on the receiver if they have the same

or similar names as those on the remote.

• “Neural-THX” and “neural THX” introduced in

the Operating Instructions and displayed in the

display window and on the GUI menu screen mean

Neural-THX Surround.

This receiver incorporates Dolby* Digital and Pro

Logic Surround and the DTS** Digital Surround

System.

* Manufactured under license from Dolby

Laboratories.

Dolby, Pro Logic, Surround EX, and the double-

D symbol are trademarks of Dolby Laboratories.

** Manufactured under license from DTS, Inc.

“DTS”, “DTS-ES” and “Neo:6” are registered

trademarks of DTS, Inc. “DTS 96/24” is a

trademark of DTS, Inc.

This receiver incorporates High-Definition

Multimedia Interface (HDMI™) technology.

HDMI, the HDMI logo and High-Definition

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.

The XM name and related logos are registered

trademarks of XM Satellite Radio Inc.

the SIRIUS dog logo are registered trademarks of

SIRIUS Satellite Radio Inc.

This product using Neural Surround, THX

Technologies is manufactured under license from

Neural Audio Corporation and THX Ltd. Sony

Corporation hereby grants the user a non-exclusive,

non-transferable, limited right to use this product,

and other related technologies dully licensed owned

by Neural Audio Corporation and/or THX Ltd.,

following US and foreign patent and patent pending

laws. Neural Surround is a trademark owned by

Neural Audio Corporation, THX is a trademark of

THX Ltd., which may be registered in some

jurisdictions.

The font type (Shin Go R) installed in this receiver

is provided by MORISAWA & COMPANY LTD.

These names are the trademarks of MORISAWA &

COMPANY LTD., and the copyright of the font also

belongs to MORISAWA & COMPANY LTD.

iPod is a trademark of Apple Inc., registered in the

U.S. and other countries.

All other trademarks and registered trademarks are

of their respective holders. In this manual, ™ and ®

marks are not specified.

Hereby, Sony Corporation declares that this

STR-DA3300ES Multi Channel AV Receiver is in

compliance with the essential requirements and

other relevant provisions of Directive 1999/5/EC.

For details, please access the following URL:

http://www.compliance.sony.de/

The Bluetooth word mark and logos are owned by

the Bluetooth SIG, Inc. and any use of such marks

by Sony Corporation is under license.

Other trademarks and trade names are those of their

respective owners.

“M-crew Server” is a trademark of Sony

Corporation.

“x.v.Color” is a trademark of Sony Corporation.

GB

4

GB

Table of Contents

Getting Started

Description and location of parts ..................6

1: Installing speakers ..................................15

2: Connecting speakers ...............................17

3: Connecting the monitor ..........................19

4a: Connecting the audio components ........21

4b: Connecting the video components .......26

5: Connecting the antennas (aerials) ...........35

6: Preparing the receiver and the remote ....36

7: Operating the receiver using the GUI

(Graphical User Interface) .....................38

8: Setting the speakers ................................41

9: Calibrating the appropriate speaker settings

automatically (Auto Calibration) ...........43

Playback

Selecting a component ................................50

Listening to a Super Audio CD/CD ............52

Watching a DVD/Blu-ray Disc ...................53

Enjoying video games ................................54

Watching video ...........................................55

Amplifier Operations

Settings for the audio

(Audio settings menu) ...........................56

Settings for the video

(Video settings menu) ............................57

Settings for HDMI (HDMI menu) ..............57

Settings for the system

(System settings menu) .........................58

Enjoying Surround Sound

Enjoying a pre-programmed sound field ....59

Adjusting the sound effect ..........................63

Using the surround back decoding mode ...65

Enjoying the surround effect at low volume

levels (NIGHT MODE) .........................67

Advanced Speakers Setting

Up

Adjusting the speaker settings manually .... 68

Adjusting the equalizer .............................. 74

Tuner Operations

Listening to FM/AM radio ......................... 76

Listening to satellite radio .......................... 79

Other Operations

Converting analog video input signals ....... 88

Using the DIGITAL MEDIA PORT

adapter ................................................... 88

Naming inputs ............................................ 92

Switching between digital and analog audio

(INPUT MODE) ................................... 93

Enjoying the sound/images from other

inputs ..................................................... 94

Changing the display ................................. 96

Using the sleep timer ............................... 100

Recording using the receiver .................... 100

Listening to the sound in another zone

(ZONE 2 operations) .......................... 101

Using a bi-amplifier connection ............... 105

Using the CONTROL S Control System

.... 106

Operating without connecting to the TV

..... 107

Using the Remote

Operating each component using the

remote ................................................. 117

Programming the remote ......................... 119

Performing several commands in sequence

automatically (Macro Play) ................ 122

Setting remote control codes that are not

stored in the remote ............................. 124

Clearing all the contents of the remote’s

memory ............................................... 126

5

GB

Additional Information

Glossary ................................................... 127

Precautions ...............................................129

Troubleshooting ....................................... 130

Specifications ........................................... 134

Index ......................................................... 137

6

GB

Description and location of parts

Getting Started

Front panel

To remove the cover

Press PUSH.

When you remove the cover, keep it out

of reach from children.

Status of the POWER button

Off

The receiver is turned off (initial

setting).

Press POWER to turn the receiver on.

You cannot turn the receiver on using

the remote.

On/Standby

Press ?/1 on the remote to turn the

receiver on or set it to the standby mode.

When you press POWER on the

receiver, the receiver will be turned off.

7

GB

Getting Started

Name Function

A POWER Press to turn the

receiver on or off.

B AUTO CAL MIC

jack

Connects to the

supplied optimizer

microphone for the

Digital Cinema Auto

Calibration function

(page 44).

C TONE MODE Adjusts FRONT/

CENTER/

SURROUND/

SURROUND BACK

BASS and TREBLE.

Press TONE MODE

repeatedly to select

BASS or TREBLE,

then turn TONE to

adjust the level.

TONE

D MEMORY/

ENTER

Press to operate a tuner

(FM/AM) and satellite

radio (XM/SIRIUS)

(page 113-115).

TUNING MODE

TUNING

E Remote sensor Receives signals from

remote commander.

F DIMMER Press repeatedly to

adjust brightness of the

display.

G DISPLAY Press repeatedly to

select information

displayed on the

display.

H SUR BACK

DECODING

Press to activate SB

DECODING

(page 65).

I Display

window

The current status of

the selected component

or a list of selectable

items appears here

(page 97).

J 2CH/A.DIRECT Press to select sound

field (page 59).

A.F.D.

MOVIE

MUSIC

K ZONE/

POWER,

SELECT

Press SELECT

repeatedly to select

zone 2 or main zone.

Each time you press

POWER, the output

signals for the selected

zone will be turned on

or off (page 101).

L DMPORT Press to select the

audio/video input

signal from the

component connected

to the DIGITAL

MEDIA PORT adapter

(page 22, 88).

M HDMI Press to select input

source from the

component connected

to the HDMI IN jack.

N PHONES jack Connects to

headphones.

O SPEAKERS

(OFF/A/B/A+B)

Switch to OFF, A, B,

A+B of the front

speakers (page 43).

P VIDEO 3 IN/

PORTABLE AV

IN jacks

Connect to a portable

audio/video component

such as a camcorder or

video game.

Q MULTI

CHANNEL

DECODING

lamp

Lights up when multi-

channel audio signals

are decoded.

Name Function

continued

8

GB

R INPUT

SELECTOR

Turn to select the input

source to play back.

To select the input

source for zone 2, press

ZONE/SELECT (

qa)

to select zone 2 first

(“ZONE 2 INPUT”

appears on the display),

then turn INPUT

SELECTOR to select

the input source.

S MASTER

VOLUME

Turn to adjust the

volume level of all

speakers at the same

time.

Name Function

9

GB

Getting Started

Rear panel

A DIGITAL INPUT/OUTPUT section

OPTICAL IN/

OUT jacks

Connect to a DVD

player, Super Audio

CD player, etc. The

COAXIAL jack

provides a better

quality sound (page

19, 21, 22, 29, 30).

COAXIAL IN

jacks

HDMI IN/

OUT* jacks

Connect to a DVD

player, Blu-ray Disc

Player, or a satellite

tuner. An image and

the sound are output

to TV or a projector

(page 19, 27).

B ANTENNA section

FM ANTENNA

jack

Connects to the FM

wire antenna (aerial)

supplied with this

receiver (page 35).

AM

ANTENNA

jack

Connects to the AM

loop antenna (aerial)

supplied with this

receiver (page 35).

XM jack Connects to the XM

Mini Tuner and

Home Dock (not

supplied) (page 80).

SIRIUS jack Connects to a

SiriusConnect Home

tuner (not supplied)

(page 80).

C RS-232C port

Used for

maintenance and

service.

continued

10

GB

* You can watch the selected input image when you

connect the MONITOR VIDEO OUT jack to a TV

(page 19). You can operate this receiver using a

GUI (Graphical User Interface) (page 38).

D DMPORT

Connects to a Sony

DIGITAL MEDIA

PORT adapter

(page 22).

E Control jack for Sony equipment

and other external components

CTRL S IN/

OUT jacks

Connect to Sony TV,

DVD player or VCR

with CONTROL S

jack (page 106).

TRIGGER

OUT jack

Connects to interlock

on/off of the power

supply of other 12V

TRIGGER

compliant

components, or the

amplifier/receiver of

zone 2 (page 103).

IR REMOTE

IN/OUT jacks

Connect an IR

repeater (page 104).

F COMPONENT VIDEO INPUT/

OUTPUT section

Y, P

B

/C

B

, P

R

/

C

R

IN/OUT*

jacks

Connect to a DVD

player, TV, or a

satellite tuner. (page

19, 29, 30).

G AUDIO INPUT/OUTPUT section

AUDIO IN/

OUT jacks

Connect to a tape

deck or MD deck, etc

(page 19, 21, 22, 25).

MULTI

CHANNEL

INPUT jacks

Connect to a Super

Audio CD player or

DVD player with an

analog audio jack for

7.1 channel or 5.1

channel sound (page

21, 24).

PRE OUT jacks Connect to an

external power

amplifier.

H VIDEO/AUDIO INPUT/OUTPUT

section

AUDIO IN/

OUT jacks

Connect to a VCR or

a DVD player etc.

(page 19, 29, 30, 31).

VIDEO IN/

OUT* jacks

AUDIO OUT

jacks

VIDEO OUT

jack

Connect to the

component in zone 2

(page 101).

I SPEAKERS section

Connects to speakers

(page 17).

11

GB

Getting Started

You can use the supplied remote RM-AAL011

to operate the receiver and to control the Sony

audio/video components that the remote is

assigned to operate (page 119).

RM-AAL011

Remote commander

Name Function

A AV ?/1 (on/

standby)

Press to turn on or off the audio/

video components that the

remote is assigned to operate

(page 119).

If you press the ?/1 (B) at the

same time, it will turn off the

receiver and other Sony

components (SYSTEM

STANDBY).

Note

The function of the AV ?/1

switch changes automatically

each time you press the input

button (C).

B ?/1 (on/

standby)

Press to turn the receiver on or

off.

If ZONE 2 is selected, only the

main receiver is turned on or off

with this button. To turn off all

components including an

amplifier in zone 2, press ?/1

and AV ?/1 (A) at the same

time (SYSTEM STANDBY).

C Input

buttons

Press one of the buttons to

select the component you want

to use. Press a pink-labeled

button after pressing SHIFT

(wk). When you press any of the

input buttons, the receiver turns

on. The buttons are factory

assigned to control Sony

components (page 50). You can

program the remote to control

non-Sony components

following the steps in

“Programming the remote”

(page 119).

D ZONE 2 Press to enable the zone 2

operation (page 101).

E TEST TONE Press to output the test tone

from each speaker.

F AMP Press to enable the receiver

operation (page 38).

G MUSIC Press to select sound field

(page 62).

H MOVIE Press to select sound field

(page 62).

continued

12

GB

I Numeric

buttons

Press to

– preset/tune to preset stations.

– select track numbers of the

CD player, DVD player, Blu-

ray Disc Player or MD deck.

Press 0/10 to select track

number 10.

– select channel numbers of

the VCR or satellite tuner.

– After pressing TV (e;),

press the numeric buttons to

select the TV channels.

J ENTER Press to enter the value after

selecting a channel, disc or

track using the numeric buttons.

MEMORY Press to store a station during

tuner operation.

K AMP MENU Press to display the menu to

operate the receiver.

L

V/v/B/b

Press V/v/B/b to select the

menu items. Then press to

enter the selection.

M OPTIONS Press to display and select items

from option menus for receiver

and DVD player, Blu-ray Disc

Player.

TOOLS Press to display and select items

from the option menus for DVD

player or Blu-ray Disc Player,

etc.

N MENU Press to display the menu to

operate the audio/video

components.

SCREEN/

DSPL

CONTROL

Press SHIFT (wk), then press

MENU to switch the display

mode of the menu between

SCREEN (to display the menu

on the TV screen) and DSPL (to

display the menu in the display

window).

O CATEGORY

+/–

Press to select the category for

satellite tuner (page 115).

Name Function

P m/M

a)

x

a)

X

a)

H

a) b)

./>

a)

Press to operate the DVD

player, Blu-ray Disc Player, CD

player, MD deck, tape deck, or

component connected to the

DIGITAL MEDIA PORT

adapter etc.

CATEGORY

MODE

Press to select the category

mode for satellite tuner

(page 115).

TUNING +/– Press to select station

(page 114).

Q PRESET

+

b)

/–

Press to register FM/AM/

satellite tuner stations or to

select preset stations.

TV CH +/– Press TV (e;), then press TV

CH +/– to operate the TV,

satellite tuner, VCR, etc.

R F1/F2 Press TV (e;), then press F1 or

F2 to select a component to

operate.

• HDD recorder

F1: HDD

F2: DVD player, Blu-ray Disc

Player

• DVD/VHS combo player

F1: DVD player, Blu-ray Disc

Player

F2: VHS

MACRO1,

MACRO2

Press AMP (6), then press

MACRO1 or MACRO2 to set

up the macro function

(page 122).

TV/INPUT Press TV/INPUT and TV (e;)

at the same time to select the

input signal (TV input or video

input).

WIDE Press repeatedly to select the

wide picture mode.

RESOLUTION

Press SHIFT (wk) then press

RESOLUTION repeatedly to

change the resolution of signals

output from the HDMI OUT or

COMPONENT VIDEO

MONITOR OUT jack

(page 88).

Name Function

13

GB

Getting Started

a)

See the table on page 118 for information on the

buttons that you can use to control each

component.

b)

The tactile dot is attached to these buttons (H,

PRESET+). Use as a mark of operation.

Notes

• Some functions explained in this section may not

work depending on the model.

• The above explanation is intended to serve as an

example only. Therefore, depending on the

component, the above operation may not be

possible or may operate differently than described.

S DVD/

TOP MENU,

MENU

Press to display the menus of

the DVD player on the TV

screen. Then use V/v/B/b and

to perform a menu

operations (page 118).

NIGHT

MODE

Press AMP (6), then press

NIGHT MODE to activate the

NIGHT MODE function

(page 67).

INPUT

MODE

Press AMP (6), then press

INPUT MODE to select the

input mode when the same

components are connected to

both digital and analog jacks

(page 93).

T MUTING Press to turn off the sound

temporarily. Press the button

again to restore the sound.

U MASTER

VOL +/–

Press to adjust the volume level

of all speakers at the same time.

TV VOL +/– Press TV (e;), then press TV

VOL +/– to adjust the volume

level of the TV.

V DISC SKIP Press to skip a disc when using

a multi-disc changer.

W RETURN/

EXIT O

Press to return to the previous

menu or exit the menu while the

menu or on-screen guide of the

VCR, DVD player, or satellite

tuner is displayed on the TV

screen.

X DISPLAY Press to select information

displayed in the display

window, TV screen of the VCR,

satellite tuner, CD player, DVD

player, Blu-ray Disc Player, or

MD deck.

Note

In the SCREEN mode, press the

button to display the menu on

the TV screen.

Name Function

Y CLEAR Press to

– clear a mistake when you

press the incorrect numeric

button.

– return to continuous

playback, etc. of the satellite

tuner or DVD player.

>10 Press to select

– track numbers over 10 of the

VCR, satellite tuner, CD

player or MD deck.

– channel numbers of the

Digital CATV terminal.

D.TUNING Press to enter direct tuning

mode (page 77, 82).

Z 2CH/

A.DIRECT

Press to select sound field

(page 59) or to switch the audio

of the selected input to analog

signal without any adjustment

(page 113).

wj A.F.D. Press to select sound field

(page 60).

wk SHIFT Press to light up the button. It

changes the remote button

function to activate the buttons

with pink printing.

wl SLEEP Press to activate the sleep timer

function and the duration which

the receiver turns off

automatically (page 100).

e; TV Press to enable the TV

operation.

ea RM SET UP Press to set up the remote.

Name Function

continued

14

GB

RM-AAU018

This remote can only be used to operate the

receiver. You can control the main functions of

the receiver with simple operations using this

remote.

Name Function

A ?/1 (on/

standby)

Press to turn a receiver on or off.

B 2CH/

A.DIRECT

Press to select sound field

(page 59).

A.F.D.

MOVIE

MUSIC

C SCREEN/

DSPL

CONTROL

Press to switch the display

mode of the menu between

SCREEN (to display the menu

on the TV screen) and DSPL (to

display the menu in the display

window).

D

V/v/B/b

After pressing SCREEN/DSPL

CONTROL (3), press V/v/B/

b to select the menu items.

Then press to enter the

selection.

E OPTIONS Press to display and select items

from option menus.

F MENU Press to display the menu to

operate the receiver.

G DMPORT Press to operate component

connected to the DIGITAL

MEDIA PORT adapter

(page 88).

N Starts play.

x Stops play.

./> Skips tracks.

H INPUT

SELECTOR

Press to select the input source

to play back.

I MASTER

VOLUME +/–

Press to adjust the volume level.

J MUTING Press to turn off the sound

temporarily. Press the button

again to restore the sound.

K RETURN/

EXIT

Press to return to the previous

menu or exit the menu.

L DISPLAY Press to select information

displayed in the display

window.

Note

In the SCREEN mode, press the

button to display the menu on

the TV screen.

M SLEEP Press to activate the sleep timer

function and the duration which

the receiver turns off

automatically (page 100).

Name Function

15

GB

Getting Started

1: Installing speakers

This receiver allows you to use a 7.1 channel

system (7 speakers and one sub woofer).

To fully enjoy theater-like multi-channel

surround sound requires five speakers (two

front speakers, a center speaker, and two

surround speakers) and a sub woofer (5.1

channel system).

Example of a 5.1 channel

speaker system configuration

AFront left speaker

BFront right speaker

CCenter speaker

DSurround left speaker

ESurround right speaker

HSub woofer

You can enjoy high fidelity reproduction of

DVD software recorded sound in the Surround

EX format if you connect one additional

surround back speaker (6.1 channel system) or

two surround back speakers (7.1 channel

system.) See “Using the surround back

decoding mode” (page 65).

Example of a 7.1 channel

speaker system configuration

AFront left speaker

BFront right speaker

CCenter speaker

DSurround left speaker

ESurround right speaker

FSurround back left speaker

GSurround back right speaker

HSub woofer

Enjoying a 5.1/7.1 channel

system

continued

16

GB

Tips

•The angle A should be the same.

• When you connect a 6.1 channel speaker system,

place the surround back speaker behind the seating

position.

• Since the sub woofer does not emit highly

directional signals, you can place it wherever you

want.

17

GB

Getting Started

2: Connecting speakers

Before connecting cords, make sure to

disconnect the AC power cord (mains lead).

ACenter speaker

BFront speaker A (L)

CFront speaker A (R)

DSurround speaker (L)

ESurround speaker (R)

FSurround back speaker (L)

b)

GSurround back speaker (R)

b)

HSub woofer

c)

a)

If you have an additional front speaker

system, connect them to the FRONT

SPEAKERS B terminals. You can select

the front speaker system you want to use

with the SPEAKERS switch (OFF/A/B/

A+B) on the front panel (page 43).

HGF

BADEC

AB

FRONT SPEAKERS

B terminals

a)

A Monaural audio cord (not supplied)

B Speaker cords (not supplied)

continued

18

GB

b)

If you connect only one surround back

speaker, connect it to the SUR BACK

SPEAKERS L terminals.

c)

When you connect a sub woofer with an auto

standby function, turn off the function when

watching movies. If the auto standby

function is set to on, it turns to standby mode

automatically based on the level of the input

signal to a sub woofer, then sound may not

be output.

Notes

• When you connect all the speakers with a nominal

impedance of 8 ohms or higher, set “Impedance” in

the Speaker settings menu to “8 Ω.” In other

connections, set it to “4 Ω.” For details, see “8:

Setting the speakers” (page 41).

• Before connecting the AC power cord (mains

lead), make sure that metallic wires of the speaker

cords are not touching each other between the

SPEAKERS terminals.

Tip

To connect certain speakers to another power

amplifier, use the PRE OUT jacks. The same signal

is output from both the SPEAKERS terminals and

the PRE OUT jacks. For example, if you want to

connect just the front speakers to another amplifier,

connect that amplifier to the PRE OUT FRONT L

and R jacks.

You can assign the SUR BACK SPEAKERS

terminals F and G to the speakers of the

zone 2. Set “Sur Back Assign” to “ZONE 2” in

the Speaker settings menu.

See “Listening to the sound in another zone

(ZONE 2 operations)” (page 101) for details

on connection and operation in zone 2.

ZONE 2 connection

19

GB

Getting Started

3: Connecting the monitor

You can watch the selected input image when

you connect the MONITOR VIDEO OUT jack

to a TV. You can operate this receiver using a

GUI (Graphical User Interface).

It is not necessary to connect all the cables.

Connect audio and video cords according to

the jacks of your components.

TV monitor

AB

A Optical digital cord (not supplied)

B Audio cord (not supplied)

C Video cord (not supplied)

D HDMI cable (not supplied)

E Component video cord (not supplied)

Audio signals

CD E

Video signals

continued

20

GB

Notes

• Before connecting cords, make sure to disconnect

the AC power cord (mains lead).

• Connect image display components such as a TV

monitor or a projector to the MONITOR VIDEO

OUT jack on the receiver. You may not be able to

record, even if you connect recording components.

• Turn on the receiver when the video and audio of a

playback component are being output to a TV via

the receiver. If the power supply of the receiver is

not turned on, neither video nor audio is

transmitted.

• Depending on the status of the connection between

the TV and the antenna (aerial), the image on the

TV screen may be distorted. In this case, place the

antenna (aerial) farther away from the receiver.

Tips

• The receiver has a video conversion function. For

details, see “Notes on converting video signals”

(page 33).

• The sound of the TV is output from the speakers

connected to the receiver if you connect the sound

output jack of the TV and the TV IN jacks of the

receiver. In this configuration, set the sound output

jack of the TV to “Fixed” if it can be switched

between either “Fixed” or “Variable.”

• The screen saver is activated when the GUI menu

is displayed on the TV screen and there has been no

operation attempted for 15 minutes.

La page charge ...

Sony STR-DA3300ES Mode d'emploi

Sony STR-DA3300ES Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents