Titan 840IX Le manuel du propriétaire

Marque: Titan

Modèle: 840IX

Catégorie: Pulvérisateur de peinture

Taper: Le manuel du propriétaire

Owner’s Manual

For professional use only

Do not use this equipment before reading this manual!

840ix Digital

Airless Sprayer

Model Numbers:

High Rider Bare 800-2030

High Rider Loaded 800-2035

Low Rider Bare 800-2040

Low Rider Loaded 800-2045

Printed in USA

NOTE: This manual contains

important warnings

and instructions.

Please read and retain

for reference.

X-Lock Theft Deterrent System

Security Code

— — — —

Serial # _ _ _ _ _ _ _ _ _ _

Important Safety Information · Read all safety information before

operating the equipment. SAVE THESE INSTRUCTIONS.

This symbol indicates a hazardous situation,

which, if not not avoided could result in death or

serious injury.

To reduce the risks of fire or explosion, electrical

shock and the injury to persons, read and

understand all instructions included in this manual.

Be familiar with the controls and proper usage of

the equipment.

HAZARD: Injection injury

A high pressure paint stream produced by this

equipment can pierce the skin and underlying

tissues, leading to serious injury and possible

amputation. See a physician immediately.

DO NOT TREAT AN INJECTION INJURY AS A SIMPLE

CUT! Injection can lead to amputation. See a physician

immediately.

The maximum operating range of the sprayer is 3300 PSI / 22.8

MPa uid pressure.

PREVENTION:

• NEVER aim the gun at any part of the body.

• Do not aim the gun at, or spray any person or animal.

• NEVER allow any part of the body to touch the uid stream.

DO NOT allow body to touch a leak in the uid hose.

• NEVER put your hand in front of the gun. Gloves will not

provide protection against an injection injury.

• ALWAYS lock the gun trigger, shut the pump off, and

release all pressure before servicing, cleaning the tip or

guard, changing tip, or leaving unattended. Pressure will

not be released by turning off the motor. The PRIME/

SPRAY valve or pressure bleed valve must be turned to

their appropriate positions to relieve system pressure.

Refer to the PRESSURE RELIEF PROCEDURE

described in this manual.

• ALWAYS keep the tip guard in place while spraying. The

tip guard provides some protection but is mainly a warning

device.

• ALWAYS remove the spray tip before ushing or cleaning

the system.

• Paint hose can develop leaks from wear, kinking and

abuse. A leak can inject material into the skin. Inspect

the hose before each use. Do not use hose to lift or pull

equipment.

• NEVER use a spray gun without a working trigger lock and

trigger guard in place.

• All accessories must be rated at or above 3300 PSI / 22.8

MPa. This includes spray tips, guns, extensions, and hose.

• Do not leave the unit energized or under pressure while

unattended. When the unit is not in use, turn off the unit and

relieve the pressure in accordance with the PRESSURE

RELIEF PROCEDURE described in this manual.

• Verify that all connections are secure before operating the

unit. Unsecured parts may eject at great force or leak a

high pressure uid stream causing severe injury.

• Always engage the trigger lock when not spraying. Verify

the trigger lock is functioning properly.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury. It is

important to treat the injury as soon as possible. DO

NOT delay treatment to research toxicity. Toxicity is a

concern with some coatings injected directly into the

blood stream. Consultation with a plastic surgeon or

reconstructive hand surgeon may be advisable.

HAZARD: HAZARDOUS VAPORS

Paints, solvents, insecticides, and other materials

can be harmful if inhaled or come in contact with the

body. Vapors can cause severe nausea, fainting, or

poisoning.

PREVENTION:

• Use a respirator or mask if vapors can be

inhaled. Read all instructions supplied

with the mask to be sure it will provide the

necessary protection.

• Wear protective eyewear.

• Wear protective clothing as required by coating manufacturer.

HAZARD: EXPLOSION OR FIRE

Solvent and paint fumes can explode or ignite.

Property damage and/or severe injury can occur.

PREVENTION:

• Provide extensive exhaust and fresh air introduction to

keep the air within the spray area free from accumulation

of ammable vapors. Solvent and paint fumes can

explode or ignite.

• Do not spray in a conned area.

• Avoid all ignition sources such as static

electric sparks, open ames, pilot lights,

electrical appliances, and hot objects.

Connecting or disconnecting power cords or

working light switches can make sparks. Paint

or solvent owing through the equipment is

able to result in static electricity.

• Do not smoke in spray area.

• Fire extinguisher must be present and in good working

order.

• Place pump at least 25 feet (7.62 meters) from the

spray object in a well ventilated area (add more hose if

necessary). Flammable vapors are often heavier than air.

Floor area must be extremely well ventilated. The pump

contains arcing parts that emit sparks and can ignite vapors.

• The equipment and objects in and around the spray area

must be properly grounded to prevent static sparks.

• Keep area clean and free of paint or solvent containers,

rags and other ammable materials.

• Use only conductive or grounded high pressure uid hose.

Gun must be grounded through hose connections.

• For electric units — power cord must be connected to a

grounded circuit.

• Always ush unit into a separate metal container, at low

pump pressure, with spray tip removed. Hold gun rmly

against side of container to ground container and prevent

static sparks.

• Follow the material and solvent manufacturer’s warnings

and instructions. Know the contents of the paints and

solvents being sprayed. Read all Material Safety Data

Sheets (MSDS) and container labels provided with

the paints and solvents. Follow the paint and solvent

manufacturer’s safety instructions.

• Use extreme caution when using materials with

a ashpoint below 70ºF (21ºC). Flashpoint is the

temperature that a uid can produce enough vapors to

ignite.

• Plastic can cause static sparks. Never hang plastic to

enclose a spray area. Do not use plastic drop cloths when

spraying ammable materials.

• Use lowest possible pressure to ush equipment.

• Do not spray onto pump assembly.

Important Safety Information · Read all safety information before

operating the equipment. SAVE THESE INSTRUCTIONS.

HAZARD: EXPLOSION HAZARD DUE TO

INCOMPATIBLE MATERIALS

Will cause property damage or severe injury.

PREVENTION:

• Do not use materials containing bleach or

chlorine.

• Do not use halogenated hydrocarbon solvents such as

bleach, mildewcide, methylene chloride and 1,1,1 -

trichloroethane. They are not compatible with aluminum.

• Contact your coating supplier about the compatibility of

material with aluminum.

HAZARD: GENERAL

Can cause severe injury or property damage.

PREVENTION:

• Read all instructions and safety precautions before

operating equipment.

• Follow all appropriate local, state, and national codes

governing ventilation, re prevention, and operation.

• The United States Government Safety Standards have

been adopted under the Occupational Safety and Health

Act (OSHA). These standards, particularly part 1910 of

the General Standards and part 1926 of the Construction

Standards should be consulted.

• Use only manufacturer authorized parts. User assumes

all risks and liabilities when using parts that do not meet

the minimum specications and safety requirements of the

pump manufacturer.

• All hoses, ttings, and lter parts must be secured before

operating spray pump. Unsecured parts can eject at great

force or leak a high pressure uid stream causing severe

injury.

• Before each use, check all hoses for cuts, leaks, abrasion

or bulging of cover. Check for damage or movement of

couplings. Immediately replace the hose if any of these

conditions exist. Never repair a paint hose. Replace it with

another grounded high-pressure hose.

• Do not kink or over-bend the hose. Airless hose can

develop leaks from wear, kinking and abuse. A leak can

inject material into the skin.

• Do not expose the hose to temperatures or pressures in

excess of those specied by manufacturer.

• Do not spray outdoors on windy days.

• Wear clothing to keep paint off skin and hair.

• Do not operate or spray near children. Keep children

away from the equipment at all times.

• Do not overreach or stand on an unstable support. Keep

effective footing and balance at all times.

• Use lowest possible pressure to ush equipment.

• Stay alert and watch what you are doing.

• Do not operate the unit when fatigued or under the

inuence of drugs or alcohol.

• For electric units — Always unplug cord from outlet before

working on equipment.

• Do not use the hose as a strength member to pull or lift the

equipment.

• Do not lift by cart handle when loading or unloading.

Grounding Instructions

This product must be grounded. In the event of an electrical

short circuit, grounding reduces the risk of electric shock by

providing an escape wire for the electric current. This product is

equipped with a cord having a grounding wire with an appropriate

grounding plug. The plug must be plugged into an outlet that

is properly installed and grounded in accordance with all local

codes and ordinances.

WARNING - Improper installation of the grounding plug can

result in a risk of electric shock.

If repair or replacement of the cord or plug is

necessary, do not connect the green grounding wire

to either at blade terminal. The wire with insulation

having a green outer surface with or without yellow

stripes is the grounding wire and must be connected

to the grounding pin.

Check with a qualied electrician or serviceman if the grounding

instructions are not completely understood, or if you are in doubt

as to whether the product is properly grounded. Do not modify

the plug provided. If the plug will not t the outlet, have the

proper outlet installed by a qualied electrician.

Grounded Outlet

Grounding Pin

Cover for grounded outlet box

IMPORTANT: Use only a 3-wire extension cord that has

a 3-blade grounding plug and a 3-slot receptacle that will

accept the plug on the product. Make sure your extension

cord is in good condition. When using an extension cord,

be sure to use one heavy enough to carry the current your

product will draw. An undersized cord will cause a drop in

line voltage resulting in loss of power and overheating. A 12

gauge cord is recommended. If an extension cord is to be

used outdoors, it must be marked with the suffix W-A after

the cord type designation. For example, a designation of

SJTW-A would indicate that the cord would be appropriate

for outdoor use.

IMPORTANT: When the sprayer is used with a generator

or uncontrolled line voltage, the use of Titan’s “Line Surge

Protector” (P/N 800-935) is recommended.

Specications

Gallons per minute (GPM) ...............0.95 (3.6 LPM)

Maximum tip sizes ...........................one gun = 0.032”

two guns = 0.021”

Maximum pressure ..........................3300 PSI (22.8 MPa)

Voltage ............................................100~120V AC, 50/60 Hz

Power ...............................................2.1 HP Innity Plus

Brushless® DC Motor

Maximum current consumption .......15 A

Weight .............................................90 lbs. (40.8 kg)

Maximum hose length .....................300’ (91.4 m)

Table of Contents

Safety Precautions ................................................................... 2

Français............................................................................. 16

Español ............................................................................. 18

General Description ................................................................. 4

Operation ................................................................................... 4

Setup ................................................................................... 4

Preparing to Paint................................................................ 5

Painting ............................................................................... 5

Control Panel Indicators ...................................................... 5

Xact Digital Control System Operation (if equipped) ........... 6

Pressure Relief Procedure .................................................. 7

Spraying .................................................................................... 8

Spraying Technique ............................................................ 8

Practice ............................................................................... 8

Cleanup ..................................................................................... 9

Maintenance .............................................................................. 9

General Repair and Service Notes...................................... 9

Replacing the Filters.......................................................... 10

Replacing the Motor Assembly.......................................... 10

Replacing the Gears.......................................................... 11

Replacing the Transducer ................................................. 11

Replacing the PRIME/SPRAY Valve ................................. 12

Servicing the Fluid Section ................................................ 12

Troubleshooting ..................................................................... 14

Xact Digital Control System Error Messages .................... 15

Parts Listings .......................................................................... 20

Main Assembly .................................................................. 20

Drive Assembly ................................................................. 21

Fluid Section Assembly ..................................................... 22

High Rider Cart.................................................................. 23

Filter Assembly .................................................................. 23

Siphon Set Assembly (low rider) ....................................... 24

Low Rider Cart .................................................................. 24

Labels ................................................................................ 24

PRIME/SPRAY Assembly ................................................. 25

Electrical Schematic .......................................................... 25

Accessories ....................................................................... 26

Warranty .................................................................................. 28

General Description

This airless sprayer is a precision power tool used for spraying

many types of materials. Read and follow this instruction manual

carefully for proper operating instructions, maintenance, and

safety information.

Return

Hose

Siphon

Tube

Pressure

Control

Knob

Control

Panel

Indicators

Xact Digital

Control

System

Fluid

Section

Filter

Motor

PRIME/

SPRAY

Valve

Outlet

Fitting

Operation

This equipment produces a fluid stream at extremely

high pressure. Read and understand the warnings

in the Safety Precautions section at the front of this

manual before operating this equipment.

Setup

Perform the following procedure before plugging in the power

cord of an electric unit.

1. Ensure that the siphon tube and the return hose are

attached and secure.

2. Using a wrench, attach a minimum of 50’ of nylon airless

spray hose to the unit. Tighten securely.

3. Attach an airless spray gun to the spray hose. Using two

wrenches (one on the gun and one on the hose), tighten

securely.

NOTE: Do not attach the tip to the spray gun yet.

Remove the tip if it is already attached.

Make sure all airless hoses and spray guns are

electrically grounded and rated at or above the

maximum operating pressure range of the airless

sprayer.

4. Make sure the pressure control knob is in its OFF position

in the black zone.

5. Fill the oil cup with one tablespoon of piston seal lubricant

(Piston Lube).

IMPORTANT: Never operate unit for more than ten seconds

without fluid. Operating this unit without fluid will cause

unnecessary wear to the packings.

6. Make sure the electrical service is 120V, 15 amp

minimum.

7. Plug the power cord into a properly grounded outlet at

least 25’ from the spray area.

IMPORTANT: Always use a minimum 12 gauge, three-wire

extension cord with a grounded plug. Never remove the

third prong or use an adapter.

Preparing a New Sprayer

If this sprayer is new, it is shipped with test uid in the uid

section to prevent corrosion during shipment and storage. This

uid must be thoroughly cleaned out of the system with mineral

spirits before you begin spraying.

IMPORTANT: Always keep the trigger lock on the spray gun

in the locked position while preparing the system.

1. Place the siphon tube into a container of mineral spirits.

2. Place the return hose into a metal waste container.

3. Set the pressure to minimum by turning the pressure

control knob to the “Min” setting in the yellow zone.

Min PSI

(Bar)

Max PSI

(Bar)

Blinking Yellow

0-200 PSI

Solid Yellow

201-1900 PSI

Solid Green

1901-3300 PSI

Motor Running

Pulse

Clean

Min. – 1900 PSI

(yellow zone)

1901 – 3300 PSI

(green zone)

Turbo PulseClean

(red zone)

OFF

(black

zone)

Pressure

Control Knob

4. Move the PRIME/SPRAY valve down to the

PRIME position.

5. Turn on the sprayer by moving the ON/OFF

switch to the ON position.

6. Allow the sprayer to run for 15–30 seconds

to ush the test uid out through the return

hose and into the waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

Preparing to Paint

Before painting, it is important to make sure that the uid in the

system is compatible with the paint that is going to be used.

NOTE: Incompatibleuidsandpaintmaycausethe

valves to become stuck closed, which would

require disassembly and cleaning of the

sprayer’suidsection.

IMPORTANT: Always keep the trigger lock on the spray gun

in the locked position while preparing the system.

1. Place the siphon tube into a container of the appropriate

solvent. Examples of the appropriate solvent are water for

latex paint or mineral spirits for oil-based paints.

Min PSI

(Bar)

Max PSI

(Bar)

Pulse

Clean

2. Place the return hose into a metal waste

container.

3. Set the pressure to minimum by turning the

pressure control knob to the “Min” setting in

the yellow zone.

4. Move the PRIME/SPRAY valve down to

the PRIME position.

NOTE: Hold the return hose in the waste

container when moving the

PRIME/SPRAY valve to PRIME in

case the sprayer is pressurized.

5. Turn on the sprayer by moving the ON/OFF switch to the

ON position.

6. Allow the sprayer to run for 15–30 seconds to ush the

old solvent out through the return hose and into the metal

waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

NOTE: Make sure that the spray gun does not have a tip

or tip guard installed.

8. Move the PRIME/SPRAY valve up to the

SPRAY position.

9. Turn on the sprayer.

10. Unlock the gun by turning the gun trigger

lock to the unlocked position.

Ground the gun by holding it

against the edge of the metal

container while flushing. Failure to

do so may lead to a static electric

discharge, which may cause a fire.

11. Trigger the gun into the metal waste container until the old

solvent is gone and fresh solvent is coming out of the gun.

Trigger lock in

locked position.

12. Lock the gun by turning the gun trigger

lock to the locked position.

13. Set down the gun and increase the

pressure by turning the pressure

control knob slowly clockwise into the

green zone.

14. Check the entire system for leaks. If

leaks occur, follow the “Pressure Relief

Procedure” in this manual before tightening any ttings or

hoses.

15. Follow the “Pressure Relief Procedure” in this manual

before changing from solvent to paint.

Be sure to follow the pressure relief procedure

when shutting down the sprayer for any purpose,

including servicing or adjusting any part of the

spray system, changing or cleaning spray tips, or

preparing for cleanup.

Painting

1. Place the siphon tube into a container of paint.

Min PSI

(Bar)

Max PSI

(Bar)

Pulse

Clean

2. Place the return hose into a metal waste

container.

3. Set the pressure to minimum by turning the

pressure control knob to the “Min” setting in

the yellow zone.

4. Move the PRIME/SPRAY valve down to the

PRIME position.

5. Turn on the sprayer by moving the ON/OFF

switch to the ON position.

6. Allow the sprayer to run until paint is

coming through the return hose into the

metal waste container.

7. Turn off the sprayer by moving the ON/OFF switch to the

OFF position.

8. Remove the return hose from the waste

container and place it in its operating

position above the container of paint.

9. Move the PRIME/SPRAY valve up to the

SPRAY position.

10. Turn on the sprayer.

11. Unlock the gun by turning the gun trigger lock to the

unlocked position.

Ground the gun by holding it

against the edge of the metal

container while flushing. Failure to

do so may lead to a static electric

discharge, which may cause a fire.

12. Trigger the gun into the metal waste container until all air

and solvent is ushed from the spray hose and paint is

owing freely. from the gun.

Trigger lock in

locked position.

13. Lock the gun by turning the gun trigger

lock to the locked position.

14. Turn off the sprayer.

15. Attach tip guard and tip to the gun

as instructed by the tip guard or tip

manuals.

POSSIBLE INJECTION HAZARD.

Do not spray without the tip guard in place. Never

trigger the gun unless the tip is in either the spray or

the unclog position. Always engage the gun trigger

lock before removing, replacing or cleaning tip.

16. Turn on the sprayer.

17. Increase the pressure by turning the pressure control knob

slowly clockwise toward the green zone and test the spray

pattern on a piece of cardboard. Adjust the pressure

control knob until the spray from the gun is completely

atomized. Try to keep the pressure control knob at the

lowest setting that maintains good atomization.

NOTE: Turning the pressure up higher than needed to

atomize the paint will cause premature tip wear

and additional overspray.

Control Panel Indicators

The following is a description of the control panel indicators.

Min PSI

(Bar)

Max PSI

(Bar)

Blinking Yellow

0-200 PSI

Solid Yellow

201-1900 PSI

Solid Green

1901-3300 PSI

Motor Running

Pulse

Clean

Pressure

Indicator

Motor Running

Indicator

Pressure Indicator

The pressure indicator shows the current operating pressure of

the sprayer. It has three different indications: blinking yellow,

solid yellow, and solid green.

Blinking Yellow

When the pressure indicator is blinking yellow, the sprayer is

operating between 0 and 200 PSI. A blinking yellow pressure

indicator means:

• The sprayer is plugged in and turned “ON”

• The sprayer is at priming pressure (little or no pressure)

• It is safe to move the PRIME/SPRAY valve between

positions

• It is safe to change or replace the spray tip

NOTE: If the pressure indicator begins blinking yellow

when the pressure control knob is set at a higher

pressure and the PRIME/SPRAY valve is in the

SPRAY position, either the spray tip is worn or

the sprayer is in need of service/repair.

Solid Yellow

When the pressure indicator is solid yellow, the sprayer is

operating between 201 and 1900 PSI. A solid yellow pressure

indicator means:

• The sprayer is at the proper pressure setting for spraying

stain, lacquer, varnish, and multi-colors

• If the pressure indicator goes to solid yellow when the

pressure is set so that it starts at solid green, it indicates

one of the following:

a. Tip Wear Indicator — when spraying with latex or at

high pressure the solid yellow appears. This means the

tip is worn and needs to be replaced.

b. Tip Too Large — when a tip that is too large for the

sprayer is put in the gun, the pressure indicator will turn

from solid green to solid yellow.

c. Fluid Section Wear — if a solid yellow pressure

indicator appears when using a new tip and the pressure

is set at maximum, service may be required (worn

packings, worn piston, stuck valve, etc...).

Solid Green

When the pressure indicator is solid green, the sprayer is

operating between 1901 and 3300 PSI. A solid green pressure

indicator means:

• The sprayer is at the proper pressure setting for spraying

oil-based and latex house paints

• The sprayer is operating at peak performance at a high

pressure setting

Motor Running Indicator

The Motor Running indicator is on when the motor is commanded

to run. This indicator is used by service centers to troubleshoot

motor problems.

Xact Digital Control System Operation (if

equipped)

The Xact Digital Control System is an optional add-on that

increases the functionality of the sprayer. It is installed directly

below the pressure control knob on the control panel. It consists

of a display and four function keys. The display shows various

menu screens that allow the user to customize and monitor

sprayer operation using the function keys.

SET PSI 3000

ACTUAL PSI 2950

MENU +–SELECT

4321

Display

Function

Keys

NOTE: The pressure control knob overrides the Xact

Digital Control System settings. Anytime the

pressure control knob is turned, the sprayer

pressure will change accordingly.

Function Keys

The function keys are numbered 1–4. Each key is labeled with

an additional function as well.

#1/Menu Key

Pressing the #1 key scrolls through the available menu screens

or performs a function described on the active menu screen.

#2/+ Key

Pressing the #2 key performs a function described on the active

menu screen or increases a value.

#3/- Key

Pressing the #3 key performs a function described on the active

menu screen or decrease a value.

#4/Select Key

Pressing the #4 key selects the active menu screen or performs

a function described on the active menu screen.

Menu Screens

Several menu screens are available for the user to customize

and monitor sprayer operation. They include Main Screen, User

Pre-Sets, Volume Pumped, Job Volume, Unit Serial #, TImers,

Job Timers, Service Time, Pressure, Security Code, Prime, and

Pulse Clean.

Main Screen

SET PSI 3000

ACTUAL PSI 2950

The Main Screen is the default screen

for the control system at sprayer startup.

Pressing the #2 key switches between PSI and MPa units of measure.

Press the #1 key to scroll through the remaining menu screens.

User Pre-Sets Screen

USER PRE-SETS

SELECT-4 MENU-1

The User Pre-Sets screen allows the

user to set four different pressure

settings and save them for future use. To select the User Pre-

Sets screen, press the #4 key.

SELECT

PRE-SETS 1-4

Press keys 1 through 4 from the Select

screen to select or change a pre-set

pressure.

PSI SETTING 750

SELECT-4 CHG-2

Press the #4 key to select the setting

and the Main Screen will appear.

PRE-SET #1 750

PRESS +/- TO CHG

Press the #2 key to change the setting.

On the following screen, use the #2/+

key to increase the setting or the #3/- screen to decrease the

setting. Once the desired setting has been reached, press the #4

key to set and the Main Screen will appear. To select or change

the remaining three pre-sets, scroll to the User Pre-Sets screen

and repeat the above procedure.

Volume Pumped Screen

VOLUME PUMPED

SELECT-4 MENU-1

The Volume Pumped screen shows the

total number of gallons or liters sprayed

by the sprayer.

GALLONS XXXXXX

PRESS 1 FOR MENU

To select the Volume Pumped screen,

press the #4 key.

Job Volume Screen

JOB VOLUME

SELECT-4 MENU-1

The Job Volume screen allows the user

to reset a gallon counter to track usage

on specic jobs.

JOB GALLONS XXXX

MENU-1 RESET-3

To select the Job Volume screen, press

the #4 key.

Unit Serial # Screen

UNIT SERIAL #

SELECT-4 MENU-1

The Unit Serial # screen shows the

sprayers serial number.

SER # XXXXXXXXXX

PRESS 1 FOR MENU

To select the Unit Serial # screen, press

the #4 key.

Timers Screen

TIMERS

SELECT-4 MENU-1

The Timers screen shows the total time

the sprayer has been turned on as well

as the total time the sprayer has been running (pumping).

ON TIME XXXXX:XX

RUN TIME XXXX:XX

To select the Timers screen, press the

#4 key.

Job Timers Screen

JOB TIMERS

SELECT-4 MENU-1

The Job Timers screen allows the user

to reset the “ON TIME” and “RUN TIME”

to track time on specic jobs.

ON TIME XXXXX:XX

RUN TIME XXXX:XX

To select the Job TImers screen, press

the #4 key. The screen will toggle

between the timers and a screen that allows the user to reset the

timers.

Service Time Screen

SERVICE TIME

SELECT-4 MENU-1

The Job Volume screen allows the user

to reset a gallon counter to track usage

on specic jobs.

The Service Time screen allows the user to set a service time

interval (in hours). Below the set time, the screens shows the

current amount of hours on the sprayer. To select the Service

Timer screen, press the #4 key.

SERVICE @ XXXHR

RUN HOURS XX

The screen will toggle between the

service hours and a screen that allows

the user to change the service time interval.

When the service time interval is set and met by the run hours,

the display will toggle between the “Main screen” and a “Service

Required” screen at sprayer startup. To stop the toggling, scroll

to the “Service Time” screen and either set a new service time

interval or set the service time to “0”.

Pressure Screen

PRESSURE

SELECT-4 MENU-1

The Pressure screen allows the user to

see the current set point pressure as

well as the actual working pressure.

SET PSI 3000

ACTUAL PSI 2950

To select the Pressure screen, press

the #4 key. This screen is also the Main

Screen.

Security Code Screen

SECURITY CODE

SELECT-4 MENU-1

The Security Code screen allows the

user to set a four digit security code

to prevent unauthorized use of the sprayer. If a security code

has been set, the control system display will ask for the code at

startup. If the correct code is entered, the display will show the

Main Screen and the sprayer will operate. If the wrong code is

entered, the display will continue to ask for the correct code and

the sprayer will be disabled. To set or change the security code,

press the #2 key.

NOTE: If the sprayer is new, no security code is set and

the Main Screen will appear at startup. Also,

whensettingasecuritycodeforthersttime,the

“Enter Old Code Number” screen will not appear.

ENTER OLD CODE

NUMBER

Enter the old security code number to

access the screen that allows the code

change. If the wrong code is entered, the display will continue to

ask for the correct code and the security code cannot be changed.

ENTER NEW CODE

NUMBER

Enter the new security code. Once the

new code is entered, the display will

automatically ask that the new code be re-entered for verication.

If the same new code is re-entered, the display will conrm that

the new code has been accepted and return to the Main Screen.

If the new code is re-entered incorrectly, the display will return to

the “Enter New Code Number” screen and the process will repeat.

NOTE: To inactivate the X-Lock security function, enter

“1111” at the “Enter New Code Number” screen

(this is the default code that leaves the sprayer

unlocked). As a result, the Main Screen will

appear at sprayer startup.

Prime Screen

PRIME

The Prime screen appears when the

pressure control knob is set at the “Min”

setting in the yellow zone.

Pulse Clean Screen

PULSE CLEAN

ACTUAL PSI XXXX

The Pulse Clean screen appears when

the pressure control knob is set at the

PULSE CLEAN position in the red zone and the PRIME/SPRAY

valve is in the PRIME position.

NOTE: If there is no action at any menu screen for 30

seconds, the display will go back to the Main

Screen.

Pressure Relief Procedure

Be sure to follow the pressure relief procedure

when shutting the unit down for any purpose,

including servicing or adjusting any part of the

spray system, changing or cleaning spray tips, or

preparing for cleanup.

Trigger lock in

locked position.

1. Lock the gun by turning the gun trigger

lock to the locked position.

2. Turn off the sprayer by moving the ON/

OFF switch to the OFF position.

3. Turn the pressure control knob

counterclockwise to its OFF position in

the black zone.

4. Unlock the gun by turning the gun

trigger lock to the unlocked position.

5. Hold the metal part of the gun rmly to

the side of a metal container to ground

the gun and avoid a build up of static

electricity.

6. Trigger the gun to remove any

pressure that may still be in the hose.

7. Lock the gun by turning the gun trigger lock

to the locked position.

8. Move the PRIME/SPRAY valve down to the

PRIME position.

Spraying

POSSIBLE INJECTION HAZARD. Do not spray

without the tip guard in place. Never trigger the

gun unless the tip is in either the spray or the

unclog position. Always engage the gun trigger

lock before removing, replacing, or cleaning tip.

Spraying Technique

The following techniques, if followed, will assure professional

painting results.

Hold the gun perpendicular to the surface and always at equal

distance from the surface. Depending on the type of material,

surface, or desired spray pattern, the gun should be held at a

distance of 12 to 14 inches (30 to 35 cm).

Move the gun either across or up and down the surface at a

steady rate. Moving the gun at a consistent speed conserves

material and provides even coverage. The correct spraying speed

allows a full, wet coat of paint to be applied without runs or sags.

Holding the gun closer to the surface deposits more paint on

the surface and produces a narrower spray pattern. Holding the

gun farther from the surface produces a thinner coat and wider

spray pattern. If runs, sags, or excessive paint occur, change to

a spray tip with a smaller orice. If there is an insufcient amount

of paint on the surface or you desire to spray faster, a larger

orice tip should be selected.

Maintain uniform spray stroke action. Spray alternately from left

to right and right to left. Begin movement of the gun before the

trigger is pulled.

start

stroke

release

trigger

pull

trigger

end

stroke

Avoid arcing or holding the gun at an angle. This will result in an

uneven nish.

Too Thick

Offspray

Arcing Gun at angle

Proper lapping (overlap of spray pattern) is essential to an even

nish. Lap each stroke. If you are spraying horizontally, aim

at the bottom edge of the preceding stroke, so as to lap the

previous pattern by 50%.

Overlap edges

1st

pass

2nd

pass

3rd

pass

4th

pass

5th

pass

For corners and edges, split the

center of the spray pattern on

the corner or edge and spray

vertically so that both adjoining

sections receive approximately

even amounts of paint.

When spraying with a shield,

hold it rmly against the surface. Angle the spray gun slightly

away from the shield and toward the surface. This will prevent

paint from being forced underneath.

Shrubs next to houses should be tied back and covered with a

canvas cloth. The cloth should be removed as soon as possible.

Titan gun extensions are extremely helpful in these situations.

Nearby objects such as automobiles, outdoor furniture, etc.

should be moved or covered whenever in the vicinity of a spray

job. Be careful of any other surrounding objects that could be

damaged by overspray.

Practice

1. Make sure that the paint hose is free of kinks and clear of

objects with sharp cutting edges.

3. Set the pressure to minimum by turning the pressure

control knob to the “Min” setting in the yellow zone.

3. Move the PRIME/SPRAY valve up to its SPRAY position.

4. Turn the pressure control knob clockwise to its highest

setting in the green zone. The paint hose should stiffen as

paint begins to ow through it.

5. Unlock the gun trigger lock.

6. Trigger the spray gun to bleed air out of the hose.

7. When paint reaches the spray tip, spray a test area to

check the spray pattern.

Good spray pattern

Paint tailing pattern

8. Use the lowest pressure setting

necessary to get a good spray

pattern. If the pressure is set

too high, the spray pattern will

be too light. If the pressure is

set too low, tailing will appear

or the paint will spatter out in

gobs rather than in a ne spray.

Cleanup

Special cleanup instructions for use with

flammable solvents:

• Always ush spray gun preferably outside and at least one

hose length from spray pump.

• If collecting ushed solvents in a one gallon metal container,

place it into an empty ve gallon container, then ush solvents.

• Area must be free of ammable vapors.

• Follow all cleanup instructions.

IMPORTANT: The sprayer, hose, and gun should be cleaned

thoroughly after daily use. Failure to do so permits material

to build up, seriously affecting the performance of the unit.

Always spray at minimum pressure with the gun

nozzle tip removed when using mineral spirits or

any other solvent to clean the sprayer, hose, or

gun. Static electricity buildup may result in a fire

or explosion in the presence of flammable vapors.

1. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

2. Remove the gun tip and tip guard and clean with a brush

using the appropriate solvent.

3. Place the siphon tube into a container of the appropriate

solvent. Examples of the appropriate solvent are water for

latex paint or mineral spirits for oil-based paints.

4. Place the return hose into a metal waste container.

5. Move the PRIME/SPRAY valve down to its

PRIME position.

NOTE: Hold the return hose in the waste

container when moving the

PRIME/SPRAY valve to PRIME in

case the sprayer is pressurized.

Min PSI

(Bar)

Max PSI

(Bar)

Pulse

Clean

6. Set the pressure to Turbo PulseClean by

turning the pressure control knob to its

PULSE CLEAN position in the red zone.

7. Turn on the sprayer by moving the ON/OFF

switch to the ON position.

8. Allow the solvent to circulate through the unit and ush the

paint out of the return hose into the metal waste container.

9. Turn off the sprayer by moving the ON/

OFF switch to the OFF position.

10. Move the PRIME/SPRAY valve up to its

SPRAY position.

11. Turn on the sprayer.

Ground the gun by holding it

against the edge of the metal

container while flushing. Failure to

do so may lead to a static electric

discharge, which may cause a fire.

12. Trigger the gun into the metal waste container until the

paint is ushed out of the hose and solvent is coming out

of the gun.

13. Continue to trigger the spray gun into the waste container

until the solvent coming out of the gun is clean.

NOTE: For long-term or cold weather storage, pump

mineral sprits through the entire system.

For short-term storage when using latex paint,

pump water mixed with Titan Liquid Shield

through the entire system (see the Accessories

section of this manual for part number).

14. Follow the “Pressure Relief Procedure” found in the

Operation section of this manual.

15. Unplug the unit and store in a clean, dry area.

IMPORTANT: Do not store the unit under pressure.

Maintenance

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to reduce

the risk of an injection injury, injury from moving

parts or electric shock. Always unplug the sprayer

before servicing!

General Repair and Service Notes

The following tools are needed when repairing this sprayer:

Phillips Screwdriver 3/8” Hex Wrench

Needle Nose Pliers 5/16” Hex Wrench

Adjustable Wrench 1/4” Hex Wrench

Rubber Mallet 3/16” Hex Wrench

Flat-blade Screwdriver 5/32” Hex Wrench

1. Before repairing any part of the sprayer, read the

instructions carefully, including all warnings.

IMPORTANT: Never pull on a wire to disconnect it. Pulling

on a wire could loosen the connector from the wire.

2. Test your repair before regular operation of the sprayer

to be sure that the problem is corrected. If the sprayer

does not operate properly, review the repair procedure

to determine if everything was done correctly. Refer to

the Troubleshooting Charts to help identify other possible

problems.

3. Make certain that the service area is well ventilated in

case solvents are used during cleaning. Always wear

protective eyewear while servicing. Additional protective

equipment may be required depending on the type of

cleaning solvent. Always contact the supplier of solvents

for recommendations.

4. If you have any further questions concerning your Titan

Airless Sprayer, call Titan:

Customer Service (U.S.) ....................... 1-800-526-5362

Fax ................................................ 1-800-528-4826

Customer Service (Canada).................. 1-800-565-8665

Fax ................................................. 1-905-856-8496

Customer Service (International) .......... 1-201-337-1240

Fax ................................................ 1-201-405-7449

Replacing the Filters

Pump Filter

Filter Body

Filter Spring

Adapter

Core Spring

Filter

O-ring

Filter Housing

1. Loosen and remove the lter

body by hand.

2. Slip the lter off of the core

spring.

3. Inspect the lter. Based on

inspection, clean or replace

the lter.

4. Inspect the o-ring. Based on

inspection, clean or replace

the o-ring.

5. Slide the new or cleaned lter

over the core spring with the

lter spring adapter in place.

Push the lter into the center

of the lter housing.

6. Slide the lter body over the

lter and thread it into the lter

housing until secure.

NOTE: Thelterhousing

should be hand-

tightened, but make

surethelterhousing

is seated fully into the

pump block.

Gun Filter

1. Move the gun trigger lock to the unlocked position.

2. Loosen and remove the handle from the gun body.

3. Turning clockwise, unscrew the lter from the gun body.

NOTE: Left-handedthreadsrequireturningthelter

clockwise to remove.

4. Turning counterclockwise, screw the new or cleaned lter

into the gun body.

5. Make sure the handle seal is in position and thread the

handle into the gun body until secure.

6. Move the gun trigger lock to the locked position.

Handle

Seal

Filter

Gun

Body

NOTE: For more detail, part number information, and

complete assembly drawings, please see the LX-

80II Professional Airless Gun Owner’s Manual

(P/N 313-2293).

Replacing the Motor Assembly

1. Unplug the unit.

2. Loosen and remove the four motor shroud screws.

Remove the motor shroud.

3. Release the tie wrap on the top of the bafe assembly and

slip the bafe assembly down off of the motor.

4. Loosen and remove the three electronic cover screws. Lift

the electronic cover off of the electronic control assembly

on the motor.

5. Disconnect all wires between the motor and the sprayer.

6. Loosen and remove the three motor mounting screws.

7. Pull the motor out of the gearbox housing.

8. With the motor removed, inspect the gears in the gearbox

housing for damage or excessive wear. Replace the

gears, if necessary.

9. Install the new motor into the gearbox housing. Make sure

the housing gasket is positioned properly.

10. Secure the motor with the three motor mounting screws.

11. Reconnect the wires between the sprayer and the new

motor. (refer to the electrical schematic in the Parts List

section of this manual).

12. Position the electronic cover over the electronic control

assembly. Secure the electronic cover with the three

electronic cover screws.

13. Slip the bafe assembly up and around the motor. Secure

the bafe assembly with the tie wrap.

14. Slide the motor shroud over the motor. Make sure the

shroud gasket is positioned properly.

15. Secure the motor shroud with the four motor shroud

screws.

Electronic Cover

Motor Shroud

Motor Shroud Screws

Motor

Baffle Assembly

Housing Gasket

Shroud Gasket

Electronic Control

Assembly

Motor Mounting

Screw

Electronic Cover

Screw

Gearbox

Housing

Replacing the Gears

1. Unplug the unit.

2. Loosen and remove the four motor shroud screws.

Remove the motor shroud.

3. Release the tie wrap on the top of the bafe assembly and

slip the bafe assembly down off of the motor.

4. Loosen and remove the three electronic cover screws. Lift

the electronic cover off of the electronic control assembly

on the motor.

5. Disconnect all wires between the motor and the sprayer.

6. Loosen and remove the three motor mounting screws.

7. Pull the motor out of the gearbox housing.

8. Inspect the armature gear on the end of the motor for

damage or excessive wear. If this gear is completely worn

out, replace the front end bell assembly.

9. Remove and inspect the 1st stage gear and 2nd stage

gear assemblies for damage or excessive wear. Replace,

if necessary.

10. Remove and inspect the front gear box assembly for

damage or excessive wear. If damaged or worn, replace

the front gear box assembly.

NOTE: Cleanandrellthegearboxcavityuptotherear

face of each gear with Lubriplate (P/N 314-171).

11. Install the motor into the gearbox housing. Make sure the

housing gasket is positioned properly.

12. Secure the motor with the three motor mounting screws.

13. Reconnect the wires between the sprayer and the motor.

(refer to the electrical schematic in the Parts List section of

this manual).

14. Position the electronic cover over the electronic control

assembly. Secure the electronic cover with the three

electronic cover screws.

15. Slip the bafe assembly up and around the motor. Secure

the bafe assembly with the tie wrap.

16. Slide the motor shroud over the motor. Make sure the

shroud gasket is positioned properly.

17. Secure the motor shroud with the four motor shroud

screws.

Front End Bell

Assembly

Armature Gear

1st Stage Gear

2nd Stage Gear

Front Gear Box

Assembly

Housing

Gasket

Shroud

Gasket

Replacing the Transducer

1. Unplug the unit.

2. Loosen and remove the four motor shroud screws.

Remove the motor shroud.

3. At the electronic control assembly, disconnect the wire

coming from the transducer.

4. Pull the grommet out of the mounting plate and slide it up

the shaft of the transducer until it is clear of the mounting

plate.

5. Using a wrench, loosen and remove the transducer from

the lter housing. Carefully thread the transducer wire out

through the mounting plate.

6. Slide the grommet off of the old transducer and onto the

new transducer.

7. Thread the new transducer wire through the mounting

plate and up to the electronic control assembly.

8. Thread the new transducer into the lter housing and

tighten securely with a wrench.

NOTE: Make sure the o-ring on the transducer is in

place before threading the transducer into the

lterhousing.

9. Push the grommet into the mounting plate.

10. Connect the transducer wire to the electronic control

assembly (refer to the electrical schematic in the Parts List

section of this manual).

11. Slide the motor shroud over the motor. Make sure the

shroud gasket is positioned properly.

12. Secure the motor shroud with the four motor shroud

screws.

Motor Shroud

Transducer

Grommet

Motor Shroud Screws

Electronic Control

Assembly

Mounting Plate

To Filter

Replacing the PRIME/SPRAY Valve

Perform the following procedure using PRIME/SPRAY valve

replacement kit P/N 800-915.

1. Push the groove pin out of the valve handle.

2. Remove the valve handle and the cam base.

3. Using a wrench, loosen and remove the valve housing

assembly.

4. Make sure the gasket is in place and thread the new valve

housing assembly into the lter block. Tighten securely

with a wrench.

5. Place the cam base over the valve housing assembly.

Lubricate the cam base with grease and line up the cam

with the lter block using the dowel pin.

6. Line up the hole on the valve stem with the hole in the

valve handle.

7. Insert the groove pin into the valve handle and through the

valve stem to secure the valve handle in position.

Gasket

Dowel Pin

Cam Base

Valve Stem

Filter

Housing

Valve Housing

Assembly

Valve

Handle

Groove Pin

Servicing the Fluid Section

Use the following procedures to service the valves and repack

the uid section. Perform the following steps before performing

any maintenance on the uid section.

1. Loosen and remove the four front cover screws. Remove

the front cover.

2. Position the crankshaft/slider assembly at the bottom,

dead-center of its stroke so that the connecting pin and

retaining ring are visible below the slider assembly. This

is done by turning the sprayer on and off in short bursts

until the connecting pin is visible below the slider housing.

3. Turn off and unplug the unit.

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to reduce

the risk of an injection injury, injury from moving

parts or electric shock. Always unplug the sprayer

before servicing!

4. Remove the return hose from the clamp on the siphon

tube.

5. Unscrew the siphon tube/siphon set from the foot valve.

6. Loosen and remove the high-pressure hose from the

nipple on the back of the upper housing of the uid

section.

Foot Valve

Housing

Viton

O-Ring

O-ring

PTFE

Back-Up

Ring

Foot Valve

Seat

Foot Valve

Ball

Foot Valve

Cage

Lower

Housing

Upper

Housing

Servicing the Valves

The design of the uid section allows

access to the foot valve and seat

as well as the outlet valve and seat

without completely disassembling the

uid section. It is possible that the

valves may not seat properly because

of debris stuck in the foot valve seat

or outlet valve seat. Use the following

instructions to clean the valves and

reverse or replace the seats.

1. Loosen and remove the foot

valve housing from the lower

housing.

2. Clean out any debris in the foot

valve housing and examine the

housing and the foot valve seat.

If the seat is damaged, reverse

or replace the seat.

3. Using two wrenches, hold the

upper housing at the wrench ats with one wrench and

loosen the lower housing with the other. Remove the

lower housing.

4. Using a 3/4” wrench, loosen and remove the outlet valve

retainer from the piston rod.

Outlet Valve

Retainer

Nylon

Washer

Outlet Valve

Seat

Outlet Valve

Ball

Outlet Valve

Cage

Outlet Valve

Seal

Piston Rod

Upper

Housing

Lower

Housing

NOTE: Always service the outlet

valve with the piston rod

attached to the pump.

This will prevent the

piston rod from rotating

during disassembly of

the outlet valve.

5. Clean out any debris and examine

the retainer and outlet valve seat.

If the seat is damaged, reverse or

replace the seat.

6. Remove, clean, and inspect the

outlet valve cage and outlet valve

ball. Replace if they are worn or

damaged.

7. Reassemble the valves by

reversing the steps above.

NOTE: During reassembly, make sure the Viton o-rings

andthePTFEback-upringsbetweentheupper

housing and lower housing as well as between

the lower housing and the foot valve housing

are lubricated with grease and in position.

Repacking the Fluid Section

NOTE: The factory-installed packings are black in

color. The replacement packings in the packing

replacement kit are white.

Retaining

Ring

Connecting

Slider

Assembly

Crankshaft

Knock-Off

Nut

Upper Seal

Retainer

Spacer

Upper

Packing

Lower

Packing

Upper

Housing

Piston Rod

Wear Ring

1. Remove the foot valve assembly

and the lower housing using

the steps in the “Servicing the

Valves” procedure above.

NOTE: The outlet valve

does not need to be

disassembled from

the piston rod for this

procedure.

2. Slide the retaining ring up on the

slider assembly to expose the

connecting pin.

3. Push the connecting pin forward

through the slider assembly and

piston. The connecting pin will

fall into a recessed area of the

gear box housing where it can

be retrieved.

4. Tap the knock-off nut with a

soft hammer so that it turns

counterclockwise and loosens.

5. Turn the uid section

counterclockwise to remove it

from the gear box housing.

6. Place the upper housing upright

in a vise by clamping on the

wrench ats.

NOTE: Do not over-tighten the

vise. Damage to the

upper housing may

occur.

7. Using a wrench, remove the

upper seal retainer.

8. Slide the piston rod out through

the bottom of the upper housing.

9. Inspect the piston rod for wear

and replace if necessary.

10. Remove the upper and lower packings from the upper

housing.

NOTE: Be careful not to scratch, score, or otherwise

damage the upper housing during removal of

the packings.

11. Clean the upper housing. Inspect the upper housing for

damage and replace if necessary.

12. Locate the new upper and lower packings and pack the

areas between the packing lips with grease. Lubricate the

o-rings on the exterior of the packings with grease.

Install upper packing

with raised lip

facing down.

Raised Lip

13. Insert the upper packing into the

top of the upper housing with the

raised lip on the packing facing

down.

14. Insert the spacer on top of the

upper packing.

15. Thread the upper seal retainer

into the upper housing and torque to 25-30 ft. lbs.

Install lower packing with

the side that has the o-ring

closest to the face of the

packing facing up.

Closer

Top

16. Pre-form the lower packing using

the lower packing sizing tool

(included in the repacking kit).

17. Insert the lower packing partially

into the bottom of the upper

housing so that the side that has

the o-ring closest to the face of

the packing faces up.

18. Push the lower packing into

position using the lower packing

insertion tool (see Fluid Section Assembly parts list for

lower packing insertion tool P/N).

19. Place the piston insertion tool (included in the repacking

kit) over the top of the piston rod.

20. Insert the piston rod into the bottom of the upper housing,

through the lower packing, through the upper packing, and

out through the upper seal retainer.

NOTE: Whenrepackingtheuidsection,makesurethe

raised lip on the bottom of the lower packing is

fully outside the packing around the piston rod

after insertion of the piston rod.

21. Remove the piston insertion tool from the top of the piston

rod.

22. Turn the knock-off nut counterclockwise until it is ush

against the upper housing.

23. Lubricate the threads on the upper housing with anti-seize

compound. Remove the upper housing from the vise.

24. Thread the upper housing into the gear box housing,

turning clockwise. When the connecting pin hole on the

piston rod lines up with the hole in the slider assembly,

insert the connecting pin.

25. Slide the retaining ring down over the connecting pin.

26. Continue to turn the upper housing clockwise until the

knock-off nut is ush against the gear box housing.

NOTE: If the nipple on the upper housing does not face

the back of the unit, turn the upper housing

counterclockwise until the nipple faces the back

of the unit. Do not turn the upper housing more

than one full turn.

27. Once the nipple is positioned, turn the knock-off nut

clockwise until it contacts the gear box housing.

28. Tap the knock-off nut with a soft hammer to tighten it

against the gear box housing.

29. Making sure that the Viton o-ring and PTFE back-up ring

are lubricated and in place, thread the lower housing into

the upper housing. Using two wrenches, hold the upper

housing at the wrench ats with one wrench and tighten

the lower housing with the other.

30. Attach the high-pressure hose to the nipple on the back of

the housing and tighten with a wrench. Do not kink the hose.

NOTE: For low rider units, make sure the hose does not

touch the cart frame. If it does, reposition the

nipple by turning the upper housing until the

hose is clear of the frame and the nipple is within

45º of the back of the unit.

31. Making sure that the Viton o-ring and PTFE back-up

ring are lubricated and in place, reassemble the foot

valve assembly and and thread it into the lower housing.

Tighten securely.

32. Thread the siphon tube/siphon set into the foot valve and

tighten securely. Make sure to wrap the threads on the down

tube/siphon tube adapter with PTFE tape before assembly.

33. Replace the return hose into the clamp on the siphon tube.

34. Place the front cover on the gearbox housing and secure

in position using the four front cover screws.

35. Turn on the sprayer by following the procedure in the

“Operation” section of this manual and check for leaks.

NOTE: Repacking kit P/N 800-273 is available. For best

results use all parts supplied in this kit.

Problem

A. The unit will not run.

B. The unit will not prime.

C. The unit will not build or

maintain pressure.

D. Fluid leakage at the upper end

of the uid section.

E. Excessive surge at the spray

gun.

F. Poor spray pattern.

G. The unit lacks power.

Cause

1. The unit is not plugged in.

2. Tripped breaker.

3. The pressure is set too low (pressure

control knob set at minimum setting does

not supply power to unit).

4. Faulty or loose wiring.

5. Excessive motor temperature.

6. ON/OFF switch is defective.

1. The PRIME/SPRAY valve is in the SPRAY

position.

2. Air leak in the siphon tube/siphon

assembly.

3. The pump lter and/or inlet screen is

clogged.

4. The siphon tube/siphon assembly is

clogged.

1. The spray tip is worn.

2. The spray tip is too large.

3. The pressure control knob is not set

properly.

4. The pump lter, gun lter, or inlet screen is

clogged.

5. Material ows from the return hose when

the PRIME/SPRAY valve is in the SPRAY

position.

6. Air leak in the siphon tube/siphon

assembly.

7. There is external uid leak.

8. There is an internal uid section leak

(packings are worn and/or dirty, valve balls

are worn).

9. Worn valve seats

10. Motor powers but fails to rotate

1. The upper packings are worn.

2. The piston rod is worn.

1. Wrong type of airless spray hose.

2. The spray tip worn or too large.

3. Excessive pressure.

1. The spray tip is too large for the material

being used.

2. Incorrect pressure setting.

3. Insufcient uid delivery.

4. The material being sprayed is too viscous.

1. The pressure adjustment is too low.

2. Improper voltage supply.

Solution

1. Plug the unit in.

2. Reset the breaker.

3. Turn the pressure control knob clockwise to supply

power to the unit and increase the pressure setting.

4. Inspect or take to a Titan authorized service center.

5. Allow motor to cool.

6. Replace the ON/OFF switch.

1. Rotate the PRIME/SPRAY valve clockwise to the

PRIME position.

2. Check the siphon tube/siphon assembly connection

and tighten or re-tape the connection with PTFE

tape.

3. Remove the pump lter element and clean. Remove

the inlet screen and clean.

4. Remove the siphon tube/siphon assembly and clean.

1. Replace the spray tip following the instructions that

came with the spray gun.

2. Replace the spray tip with a tip that has a smaller

orice following the instructions that came with the

spray gun.

3. Turn the pressure control knob clockwise to increase

the pressure setting.

4. Remove the pump lter element and clean. Remove

the gun lter and clean. Remove the inlet screen

and clean.

5. Clean or replace the PRIME/SPRAY valve.

6. Check the siphon tube/siphon assembly connection

and tighten or re-tape the connection with PTFE

tape.

7. Check for external leaks at all connections. Tighten

connections, if necessary.

8. Clean the valves and service the uid section

following the “Servicing the Fluid Section” procedure

in the Maintenance section of this manual.

9. Reverse or replace the valve seats following the

“Servicing the Fluid Section” procedure in the

Maintenance section of this manual.

10. Take unit to a Titan authorized service center.

1. Repack the pump following the “Servicing the Fluid

Section” procedure in the Maintenance section of this

manual.

2. Replace the piston rod following the “Servicing the

Fluid Section” procedure in the Maintenance section

of this manual.

1. Replace hose with a minimum of 50’ of 1/4”

grounded textile braid airless paint spray hose.

2. Replace the spray tip following the instructions that

came with the spray gun.

3. Rotate the pressure control knob counterclockwise to

decrease spray pressure.

1. Replace the spray tip with a new or smaller spray tip

following the instructions that came with the spray

gun.

2. Rotate the pressure control knob to adjust the

pressure for a proper spray pattern.

3. Clean all screens and lters.

4. Add solvent to the material according to the

manufacturer’s recommendations.

1. Rotate the pressure control knob clockwise to

increase the pressure setting.

2. Reconnect the input voltage for 120V AC.

Troubleshooting

English

Xact Digital Control System Error

Messages

The following error message screens appear whenever the Xact

Digital Control System detects a problem with the sprayer. Once

a problem occurs and the error message appears, the sprayer

will shut down.

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to reduce the

risk of an injection injury, injury from moving parts

or electric shock. Always unplug the sprayer

before servicing!

Check Paint Screen (E1)

CHECK PAINT

The Check Paint screen appears when

the pump pressure drops to a very

low level and the pressure control knob has not been adjusted.

Check the paint level and rell. Restart the sprayer by following

the “Painting” procedure in the Operation section of this manual.

Check Transducer Screen (E2)

CHECK TRANSDUCER

The Check Transducer screen appears

when the transducer has become

disconnected or is defective. Take the sprayer to a Titan

authorized service center for repair.

Check Motor Screen (E3)

CHECK MOTOR

The Check Motor screen appears when

the motor or motor sensor is defective.

Take the sprayer to a Titan authorized service center for repair.

Low Voltage Screen (E4)

LOW VOLTAGE

The Low Voltage screen appears when

the sprayer shuts down because of low

input voltage. Check the power supply and correct the problem.

Restart the sprayer by following the “Painting” procedure in the

Operation section of this manual.

High Motor Temperature Screen (E5)

HIGH MOTOR

TEMPERATURE

The High Motor Temperature screen

appears when the temperature of the

motor has risen too high. Take the sprayer to a Titan authorized

service center for repair.

High Control Temperature Screen (E6)

HIGH CONTROL

TEMPERATURE

The High Control Temperature screen

appears when the temperature of the

Xact Digital Control System has risen too high. Take the sprayer

to a Titan authorized service center for repair.

High Load Check Mechanism Screen (E7)

HIGH LOAD

CHECK MECHANISM

The High Load Check Mechanism

screen appears when the sprayer shuts

down because of high current or when the sprayer goes into

current fold back mode.. Take the sprayer to a Titan authorized

service center for repair.

Exceeded Pressure Limit Screen (E8)

EXCEEDED

PRESSURE LIMIT

The Exceeded Pressure Limit screen

appears when the sprayer pressure

exceeds 3300 PSI / 22.8 MPa. Take the sprayer to a Titan

authorized service center for repair.

Communication Error Screen (E9)

COMMUNICATION

ERROR

The Communication Error screen

appears when the Xact Digital Control

System loses communication with the control panel. Take the

sprayer to a Titan authorized service center for repair.

Français

Consignes de sécurite important · Lire toutes ces consignes avant

d’utiliser l’appareil. GARDER CES CONSIGNES.

Indique une situation à risque, laquelle, si elle n’est pas

évitée, peut entraîner des blessures graves, voire la mort.

Pour réduire les risques d’incendie ou d’explosion, de

choc électrique et de blessure, vous devez lire et

comprendre les directives figurant dans ce manuel.

Familiarisez-vous avec les commandes et l’utilisation

adéquate de l’équipement.

DANGER : INJECTION CUTANÉE

A high pressure paint stream produced by this Le jet de

haute pression produit par cet appareil peut transpercer

la peau et les tissus sous-jacents, causant des blessures

graves pouvant entraîner l’amputation.

NE PAS TRAITER ce type de BLESSURE COMME

UNE SIMPLE COUPURE! Une amputation peut en résulter. ON doit

consulter un médicin sur-le-champ.

La pression maximale de ce pulvérisateur est d’environ 3 300 PSI / 22,8

MPa.

MESURES PRÉVENTIVES :

• Ne pas pointer le pistolet vers une partie du corps.

• Ne pas pointer le pistolet vers une personne ou un animal; ne pas

pulvériser non plus de produit dessus.

• NE JAMAIS mettre une partie du corps devant le jet de produit.

NE JAMAIS toucher les fuites du exible de pulvérisation.

• NE JAMAIS mettre la main, même gantée, devant le pistolet (les

gants n’offrent aucune protection contre les blessures par injection).

• TOUJOURS verrouiller la détente, arrêter la pompe et relâcher

toute la pression avant d’effectuer la maintenance de l’appareil ou

de le laisser sans surveillance, d’en nettoyer le protège-embout

ou l’embout, ou de remplacer ce dernier. La pression ne sera

pas relâchée par le simple arrêt du moteur; pour ce faire, on

doit se servir du bouton PRIME/SPRAY (se reporter à la section

Comment libérer la pression, du présent manuel).

• TOUJOURS s’assurer que le protège-embout est en place

avant de pulvériser. Il est cependant à noter que, s’il assure une

certaine protection, ce dispositif joue surtout un rôle préventif.

• TOUJOURS retirer l’embout avant de vidanger ou de nettoyer

l’appareil.

• toujours inspecter le exible avant de commencer; celui-ci

peut présenter des fuites attribuables à l’usure, à une exion

excessibe ou à un traitement abusif, lesquelles fuites présentent

des risques d’injection cutanée. Ne pas utiliser le exible pour

soulever ou tirer l’équipement.

• NE JAMAIS utiliser de pistolet sans verrou de détente et protège-

doigts.

• Tous les accessoires (pistolets, embouts, rallonges, exibles etc.)

doivent pouvoir subir une pression nominale de 3 300 PSI / 22,8

MPa ou plus.

• Ne laissez pas l’appareil sous tension ou sous pression quand

vous vous en éloignez. Quand vous n’utilisez pas l’appareil,

éteignez-le et libérez la pression conformément aux instructions

Comment libérer la pression, du présent manuel.

• Vériez que toutes les connexions sont bien serrées avant

d’utiliser l’appareil. Toute pièce qui n’est pas xée solidement

risque d’être projetée violemment ou d’entraîner la fuite d’un jet

de liquide à une pression extrêmement élevée, ce qui pourrait

causer des blessures graves.

• Verrouillez toujours la détente quand vous ne pulvérisez pas.

Vériez que le verrou de la détente fonctionne correctement.

REMARQUE À L’INTENTION DES MÉDECINS :

Les injections cutanées sont des lésions traumatiques; il

importe donc de les traiter sans délai. On NE DOIT PAS retarder

cetraitementsousprétextedevérierlatoxicitéduproduiten

cause, celle-ci n’étant conséquente que dans le cas d’injection

directe de certains produits dans le système sanguin. Il pourrait

s’avérer nécessaire de consulter un plasticien ou un spécialiste

en chirurgie reconstructive de la main.

DANGER : ÉMANATIONS DANGEREUSES

Certains produits (peintures, solvants, insecticides ou

autres) peuvent être nocifs s’ils sont inhalés ou entrent en

contact avec l’organisme. Les émanations de ces produits

peuvent provoquer de graves nausées, évanouissements

ou empoisonnements.

MESURES PRÉVENTIVES :

• Se servir d’un masque ou d’un respirateur s’il

y a risque d’inhalation (lire toutes les directives

concernant ces dispositifs an de s’assurer qu’ils

offrent la protection requise).

• Porter des lunettes de protection.

• Porter les vêtements de protection prescrits par le fabricant du

produit utilisé.

DANGER : EXPLOSION OU INCENDIE

Les émanations de certains produits peuvent exploser

ou s’enammer, et risquent d’entraîner des dommages

matériels ou de graves blessures.

MESURES PRÉVENTIVES :

• S’assurer que l’aire de travail est dotée de moyens d’évacuation

d’air vicié et d’introduction d’air frais pour éviter l’accumulation de

vapeurs inammables. Les vapeurs dégagées par la peinture ou

les solvants peuvent provoquer une explosion ou s’enammer.

• Ne pas pulvériser de produit dans un endroit clos.

• Ne pas travailler près de sources d’ignition (décharges

électrostatiques ou étincelles provoquées par le branchement/

débranchement d’appareils ou la commutation d’interrupteurs,

d’appareils électriques, ammes nues, veilleuses,

objets chauds, etc.). La peinture ou le solvant

s’écoulant dans l’équipement peut générer de

l’électricité statique.

• Ne pas fumer dans l’aire de travail.

• L’aire de travail doit être munie d’un extincteur en bon

état de marche.

• Prévoir un espace d’au moins 7.62 mètres entre la pompe et l’objet

à pulvériser s’ils sont dans la même pièce bien ventilée (rallonger le

exible au besoin). Les vapeurs inammables étant souvent plus lourdes

que l’air, l’espace au-dessus du plancher doit être particulièrement bien

aéré. La pompe contient des pièces qui produisent des arcs et émettent

des étincelles pouvant enammer les vapeurs.

• Les appareils et objets à l’intérieur ou à proximité de l’aire de

travail doivent être adéquatement mis à la terre pour éviter les

décharges électrostatiques.

• Veillez à ce que la zone soit propre et exempte de contenants de

peinture ou de solvant, chiffons ou autres matériaux inammables.

• Les exibles dont on se sert doivent être conçus pour subir les

pressions élevées et faits de matériaux conducteurs ou mis à la

terre adéquatement; le pistolet sera mis à la terre par le biais de

ses raccords aux exibles.

• Pour les appareils électriques — Le cordon d’alimentation doit

être branché à un circuit trilaire.

• L’appareil doit toujours être vidangé à basse pression, embout

retiré, dans un contenant métallique distinct. Tenir le pistolet

contre la paroi du contenant de manière à mettre ce dernier à la

terre et à prévenir les décharges électrostatiques.

• Toujours respecter les mises en garde et les directives du

fabricant des produits et solvants utilisés. On doit connaître les

produits contenus dans les peintures et solvants qu’on pulvérise.

Lire les ches techniques santé-sécurité (FTSS) et les étiquettes

des contenants fournies avec les peintures et solvants. Suivres

les consignes de sécurité du fabricant de peinture et de solvant.

• S’entourer de toutes les précautions possibles lorsqu’on utilise

des produits ayant un point d’éclair inférieur à 21°C (70°F). Le

point d’éclair est la température à laquelle le liquide peut créer

sufsamment de vapeurs et s’enammer.

• Le plastique est générateur de décharges électrostatiques; ne jamais

en suspendre pour fermer une aire de travail ou en utiliser en guise

de toile de protection lorsqu’on pulvérise un produit inammable.

• Se servir de la pression la plus basse possible pour vidanger

l’appareil.

• Ne pas pulvériser de produit sur la pompe.

Français

Consignes de sécurite important · Lire toutes ces consignes avant

d’utiliser l’appareil. GARDER CES CONSIGNES.

DANGER : EXPLOSION CAUSÉE PAR DES

PRODUITS INCOMPATIBLES

Ce type d’explosion peut entraîner des dommages

matériels ou des blessures graves.

MESURES PRÉVENTIVES :

• Ne pas utiliser de produits contenant du chlore ou du javellisant.

• Ne pas utiliser de solvants à base de halons comme l’eau de

javel, les agents antimoisissure, le chlorure de méthylène et le

trichloroéthane-1-1-1, lesquels ne sont pas compatibles avec

l’aluminium.

• Communiquer avec le fournisseur du produit concerné pour en

connaître la compatibilité avec l’aluminium.

DANGER : GÉNÉRALITÉS

D’autres dangers peuvent entraîner des dommages matériels ou des

blessures graves.

MESURES PRÉVENTIVES :

• Lire toutes les directives et consignes de sécurité avant d’utiliser

l’appareil.

• Observer tous les codes locaux, provinciaux, d’état et nationaux

régissant la ventilation, la prévention des incendies et le

fonctionnement de l’appareil.

• Aux États-Unis, le gouvernement a adopté des normes de

sécurité en vertu de l’Occupational Safety and Health Act

(OSHA). Le cas échéant, on doit les consulter, notamment les

parties 1910 des normes générales et 1926 des normes de

construction.

• N’utiliser que les pièces autorisées par le fabricant; les

utilisateurs qui choisiront d’utiliser des composants dont les

caractéristiques techniques et les exigences en matière de

sécurité sont inférieures devront en assumer tous les risques et

responsabilités.

• Tous les raccords, les tuyaux et les bouchons de remplissage

doivent être xés solidement en place avant d’utiliser la pompe

de pulvérisation. Toute pièce qui n’est pas xée solidement

risque d’être projetée violemment ou d’entraîner la fuite d’un jet

de liquide à une pression extrêmement élevée, ce qui pourrait

causer des blessures graves.

• Avant chaque utilisation, examiner tous les exibles an de

conrmer l’absence de coupures, de fuites, d’abrasions ou

de renements. Vérier également l’intégrité des raccords.

Remplacer sans délai les pièces qui semblent présenter des

défectuosités. Ne jamais tenter de réparer un exible; remplacer

ceux qui font défaut par des modèles haute pression, avec mise à

la terre.

•. Ne faites pas de nouer avec le tuyau et ne le tordez pas trop. Le

tuyau à vide peut présenter des fuites suite à l’usure, les nouer

ou les mauvais traitements. Une fuite risque d’injecter du produit

dans la peau.

•. N’exposez pas le tuyau à des températures ou des pressions

supérieures à celles spéciées par le fabricant.

• Ne pas pulvériser à l’extérieur par grands vents.

• Porter des vêtements aptes à protéger la peau et les cheveux du

produit utilisé.

• Ne pas utiliser le pistolet ou ne pas pulvériser de produits

en présence d’enfants à proximité. Éloigner les enfants de

l’équipement en tout temps.

• Ne pas s’étirer ni ne travailler sur un support instable. Toujours

garder les deux pieds au sol pour rester en équilibre.

• Se servir de la pression la plus basse possible pour vidanger

l’appareil.

• Rester vigilant et faire attention à ce que l’on fait.

• Ne pas se servir de l’équipement en cas de fatigue ou si vos

aptitudes sont affaiblies par la consommation de drogues ou de

boissons alcoolisées.

• Pour les appareils électriques — Débranchez toujours le cordon

électrique de la prise avant de travailler sur l’équipement.

• N’utilisez pas le tuyau pour tirer ou soulever l’équipement.

• Ne pas soulever par la poignée de chariot en chargeant ou en

déchargeant.

Instructions de mise à la terre

Cet appareil doit être mis à la terre. La mise à la terre réduit les risques

d’électrocution lors d’un court-circuit en permettant au courant de

s’écouler par le l de mise à la terre. Cet appareil est muni d’un cordon

électrique avec l de mise à la terre ainsi que d’une che de terre. La

che doit être branchée sur une prise installée correctement et mise à la

terre conformément à la réglementation et aux codes en vigueur.

MISE EN GARDE - Le fait de ne pas brancher

correctement la fiche trifilaire de l’appareil peut entraîner

des risques de choc électrique.

Si on doit réparer ou remplacer le cordon ou la che, ne pas raccorder

le l de terre à la borne des broches plates (lames) de cette dernière. Ce

l, normalement vert (avec ou sans rayures jaunes), doit être relié à la

broche de terre.

Consulter un technicien ou un électricien qualié à défaut de comprendre

l’ensemble des présentes directives ou en cas d’incertitude quant à la

mise à terre de l’appareil. Ne pas modier la che de l’appareil; si elle ne

s’adapte pas dans la prise voulue, faire remplacer cette dernière par un

électricien qualié.

Prise trifilaire

Broche de mise à la terre

Plaque murale de la prise

IMPORTANT : Utiliser uniquement une rallonge à trois fils

munie d’une fiche de terre dans une prise secteur mise à la terre

correspondant au type de fiche de l’appareil. S’assurer que votre

rallonge est en bon état. Lorsque vous utilisez une rallonge,

assurez-vous qu’elle soit d’un calibre suffisant pour supporter

l’intensité du courant requise par l’appareil. Une rallonge trop

mince entraîne une chute de tension, une diminution de l’intensité

et une surchauffe. Une rallonge de calibre 12 est recommandée.

Si vous devez utiliser une rallonge à l’extérieur, celle-ci doit

comprendre la marque W-A après la désignation indiquant le type de

cordon. Par exemple, la désignation SJTW-A indique que le cordon

est conçu pour être utilisé à l’extérieur.

Español

Información de seguridad importante · Lea toda la información de

seguridad antes de operar el equipo. GUARDE ESTAS INSTRUCCIONES.

Indica una situación peligrosa que, de no evitarse, puede

causar la muerte o lesiones graves.

Para reducir los riesgos de incendios, explosiones,

descargas eléctricas o lesiones a las personas, lea y

entienda todas las instrucciones incluidas en este

manual. Familiarícese con los controles y el uso

adecuado del equipo.

PELIGRO: LESIÓN POR INYECCIÓN

El ujo de pintura a alta presión que produce este

equipo puede perforar la piel y los tejidos subyacentes,

ocasionando lesiones graves y posible amputación.

CONSULTE A UN MÉDICO INMEDIATAMENTE.

¡NO TRATE LA LESIÓN POR INYECCIÓN COMO UNA

CORTADURA SIMPLE! La inyección puede ocasionar amputación.

Consulte a un médico inmediatamente.

La gama operativa máxima de la pistola es de 3300 PSI / 22.8 MPa de

presión del líquido.

PREVENCIÓN:

• NUNCA apunte la pistola a ninguna parte del cuerpo.

• No apunte con la pistola ni rocíe a cualquier persona o animal.

• NUNCA deje que ninguna parte del cuerpo toque el ujo de

líquido. NO deje que el cuerpo toque una fuga de la manguera de

líquido.

• NUNCA ponga la mano frente a la pistola. Los guantes no

protegen contra una lesión por inyección.

• SIEMPRE ponga el seguro del gatillo, apague la bomba y

libere toda la presión antes de dar servicio, limpiar la boquilla o

protección, cambiar la boquilla o dejar la pistola sin supervisión.

No se libera la presión al apagar el motor. Debe girarse la perilla

PRIME/ SPRAY (CEBAR/ROCIAR) a PRIME (CEBAR) para

aliviar la presión. Consulte el PROCEDIMIENTO PARA ALIVIAR

LA PRESIÓN descrito en este manual.

• SIEMPRE mantenga la protección de la boquilla en su sitio

al rociar. La protección de la boquilla sirve principalmente de

dispositivo de advertencia.

• SIEMPRE retire la boquilla rociadora antes de enjuagar o limpiar

el sistema.

• La manguera de pintura puede presentar fugas por desgaste,

dobleces y maltrato. La fuga puede inyectar material traspasando

la piel. Inspeccione la manguera antes de cada uso. No use

mangueras para levantar o tirar del equipo.

• NUNCA use una pistola rociadora sin contar con el seguro y la

protección del gatillo.

• Todos los accesorios deben tener capacidades nominales de

3300 PSI / 22.8 MPa como mínimo. Esto incluye las boquillas

rociadoras, pistolas, extensiones y manguera.

• No deje el aparato con corriente ni con presión cuando nadie esté

pendiente de ella. Cuando no utilice el aparato, apáguelo y libere

la presión siguiendo las instrucciones del PROCEDIMIENTO

PARA ALIVIAR LA PRESIÓN descrito en este manual.

• Antes de utilizar el aparato, verique que todas las conexiones

son seguras. Las partes no aseguradas pueden ser expulsadas

con gran fuerza o ltrar uido a alta presión y provocar lesiones

severas.

• Ponga siempre el seguro del gatillo cuando no esté pulverizando.

Verique que el seguro del gatillo funciona correctamente.

NOTA PARA EL MÉDICO:

La inyección a través de la piel es una lesión traumática. Es

importante tratar la lesión tan pronto sea posible. NO retrase

el tratamiento para investigar la toxicidad. La toxicidad es

un factor a considerar con ciertos revestimientos inyectados

directamente en la corriente sanguínea. Puede ser aconsejable

consultar con un cirujano plástico o un cirujano especialista en

reconstrucción de las manos.

PELIGRO: VAPORES PELIGROSOS

Las pinturas, solventes, insecticidas y demás materiales

pueden ser nocivos si se inhalan o toman contacto con

el cuerpo. Los vapores pueden causar náuseas graves,

desmayos o envenamiento.

PREVENCIÓN:

• Use un respirador o mascarilla si pueden

inhalarse los vapores. Lea todas las instrucciones

suministradas con la mascarilla para revisar que

brinde la protección necesaria.

• Use lentes protectores.

• Use ropa protectora según lo indique el fabricante del

revestimiento.

PELIGRO: EXPLOSIÓN O INCENDIO

Los vapores de solventes y pinturas pueden explotar o

inamarse. Pueden producirse daños materiales, lesiones

graves o ambos.

PREVENCIÓN:

• Cuente con escape y entrada de aire fresco para mantener el aire

dentro de la zona de aplicación sin acumulaciones de vapores

inamables. Los gases producidos por solventes o pinturas

pueden causar explosiones o incendios.

• No rocíe en lugares cerrados.

• Evite todas las fuentes de ignición como las chispas de

electricidad estática, las llamas expuestas,

appliances electricidad, las luces piloto y los

objetos calientes. La conexión o desconexión de

cables eléctricos o interruptores de luz operativos

puede producir chispas. Si la pintura o el solvente

uyen por el equipo se puede generar electricidad

estática.

• No fume en el área de aplicación.

• Debe haber un extintor de incendios en buen estado.

• Coloque la bomba de pintura a un mínimo de 7.62 meters (25

pies) del objeto a pintar dentro de un área bien ventilada (añada

más manguera si es necesario). Los vapores inamables son

generalmente más pesados que el aire. El área debe estar

sumamente bien ventilada.

• El equipo y los objetos dentro y alrededor del área a pintar deben

estar debidamente conectados a tierra para evitar las chispas de

estática.

• Mantenga el área limpia y libre de contenedores de pintura o

solvente, trapos y otros materiales inamables.

• Use solamente una manguera conductora o conectada a tierra

para líquidos a alta presión. La pistola debe conectarse a tierra a

través de las conexiones de la manguera.

• Para las aparatos eléctricas — Debe conectarse el cable eléctrico

a un circuito a tierra.

• Siempre enjuague la unidad dentro de un recipiente metálico

separado, con la bomba a baja presión y habiendo sacado la

boquilla rociadora. Sostenga la pistola rmemente contra el

costado del recipiente para conectar a tierra el mismo y evitar

chispas de estática.

• Siga las advertencias e instrucciones del fabricante del material

y del solvente. Conozca los contenidos de las pinturas y los

solventes con los que rocía. Lea todas las Hojas de Datos sobre

Seguridad de Materiales (MSDS) y las etiquetas del contenedor

provistas con las pinturas y los solventes. Siga las instrucciones

de seguridad del fabricante de pinturas o solventes.

• Tenga muchísmo cuidado al usar materiales cuyo punto de

ignición sea inferior a 70°F (21°C). El punto de inamación es la

temperatura a la que un uido puede producir vapores sucientes

para encenderse.

• El plástico puede causar chispas de estática. Nunca cuelgue

plásticos para cerrar una zona a pintar. No use mantas plásticas

al aplicar materiales inamables.

• Use la presión más baja posible para enjuagar el equipo.

• No rocíe el ensamblaje de la bomba.

Español

Información de seguridad importante · Lea toda la información de

seguridad antes de operar el equipo. GUARDE ESTAS INSTRUCCIONES.

PELIGRO: POSIBLE EXPLOSIÓN DEBIDO A

MATERIALES INCOMPATIBLES

Causará daños materiales o lesiones graves.

PREVENCIÓN:

• No use materiales que contengan blanqueador o

cloro.

• No use solventes de hidrocarburos halogenados como

blanqueador, mohocida, cloruro de metileno y 1,1,1 tricloroetano.

No son compatibles con el aluminio.

• Diríjase al proveedor de revestimientos para obtener los datos de

compatibilidad del material con el aluminio.

PELIGRO: GENERAL

Puede causar daños materiales o lesiones graves.

PREVENCIÓN:

• Lea todas las instrucciones y las precauciones de seguridad

antes de operar el equipo.

• Siga todos los códigos locales, estatales y nacionales

correspondientes que rijan la ventilación, prevención de incendios

y operación.

• Se han adoptado las normas de seguridad del Gobierno de los

Estados Unidos según la Ley de seguridad ocupacional y salud

(Occupational Safety and Health Act, OSHA). Deben consultarse

estas normas, particularmente el apartado 1910 de las Normas

generales y el apartado 1926 de las Normas de construcción.

• Utilice solamente componentes autorizados por el fabricante.

El usuario asume todo riesgo y responsabilidad al utilizar

componentes que no cumplan con las especicaciones mínimas

y requisitos de seguridad del fabricante de la bomba.

• Todos los acopladores, las mangueras y las tapas de los ltros

deben estar asegurados antes de operar la bomba de rocío. Las

partes no aseguradas pueden ser expulsadas con gran fuerza o

ltrar uido a alta presión y provocar lesiones severas.

• Antes de cada uso, revise todas las mangueras en busca de

cortes, fugas, abrasión o hinchazón de la cubierta. Revise

si hay daños o movimiento de los acoplamiento. Cambie

inmediatamente la manguera si existe alguna de estas

condiciones. Nunca repare una manguera de pintura. Cámbiela

por otra manguera conectada a tierra apta para alta presión.

• No retuerza ni doble la manguera en exceso. En la manguera

airless pueden aparecer fugas a causa del desgaste, de

retorcimientos o de un mal uso. Una fuga puede inyectar material

en la piel.

• No exponga la manguera a temperaturas o presiones que

superen las especicadas por el fabricante.

• No pinte en exteriores en días con viento.

• Use ropa que mantenga la pintura alejada de la piel y el cabello.

• No lo opere ni rocíe cerca de los niños. Mantenga a los niños

alejados del equipo en todo momento.

• No se asome ni se pare sobre soportes inestables. Mantenga

siempre la posición rme y el equilibrio efectivos.

• Use la presión más baja posible para enjuagar el equipo.

• Manténgase alerta y mire lo que hace.

• No utilice la unidad cuando se encuentre cansado o bajo la

inuencia de las drogas o el alcohol.

• Para las aparatos eléctricas — Desenchufe siempre el cable

antes de trabajar en el equipo.

• No utilice la manguera como elemento de fuerza para tirar del

equipo o levantarlo.

• No levantar por la manija del carro al cargar o descargando.

Instrucciones para conectar a tierra

Este producto se debe conectar a tierra. En caso de que ocurra un

corto circuito, la conexión a tierra reduce el riesgo de choque eléctrico

al proporcionar un alambre de escape para la corriente eléctrica. Este

producto está equipado con un cable que tiene un alambre de conexión a

tierra con un enchufe de conexión a tierra apropiado. El enchufe se debe

enchufar en una toma de corriente que se haya instalado y conectado a

tierra debidamente, de acuerdo con todos los códigos y estatutos locales.

ADVERTENCIA - La instalación incorrecta del enchufe a

tierra puede ocasionar un riesgo de choque eléctrico.

Si es necesario reparar o cambiar el cable o el enchufe, no conecte el

cable verde a tierra a ninguno de las terminales de espiga plana. El cable

con aislamiento de color verde por fuera con o sin rayas amarillas es el

alambre a tierra y debe conectarse a la espiga a tierra.

Consulte a un electricista o técnico de servicio capacitado si las

instrucciones para la conexión a tierra no se entienden claramente o si

tiene dudas en cuanto a que el producto esté debidamente conectado a

tierra. No modifique el enchufe que se incluye. Si el enchufe no encaja

en el receptáculo, pida a un electricistas capacitado que instale un

receptáculo adecuado.

Receptáculo conectado a tierra

Pata a tierra

Tapa de la caja de receptáculo conectada a tierra

IMPORTANTE: Use solamente extensiones trifilares que tengan un

enchufe de conexión a tierra de 3 hojas y un receptáculo de triple

ranura que acepte el enchufe del producto. Asegúrese de que su

extensión esté en buenas condiciones. Cuando use una extensión,

asegúrese de usar una que sea lo suficientemente resistente como

para soportar la corriente que descargue su producto. Un cable de

un tamaño menor causará una caída de voltage en la línea que dará

como resultado una pérdida de energía y un sobrecalenta|ôento. Se

recomienda usar un cable de calibre 12. Si se utiliza un cable de

extensión en el exterior, tiene que estar marcado con el sufijo W-A

después de la designación del tipo de cable. Por ejemplo, SJTW-A

para indicar que el cable es apropiado para uso en exteriores.

Parts List

Main Assembly

Item Part # Description Quantity

1 800-600A Cart assembly ...........................................1

2 800-036 Grommet ...................................................2

3 ---------- Drive assembly (see separate listing).......1

4 761-178 Screw ........................................................4

5 800-324 Pail hook ...................................................1

6 763-551 Lock washer .............................................2

7 858-625 Screw ........................................................2

8 800-328 Knock-off nut ............................................1

9 800-300 Fluid section assembly .............................1

10 451-241 Siphon tube ..............................................1

11 730-334 Hose clamp ...............................................1

12 710-046 Inlet screen ...............................................1

Item Part # Description Quantity

14 800-904 Return hose ..............................................1

15 800-900 Filter assembly .........................................1

16 812-003 Outlet tting ..............................................1

17 800-915 PRIME/SPRAY valve assembly ...............1

18 800-269 Fitting ........................................................1

19 800-267 Fitting ........................................................1

20 860-002 Lock washer .............................................2

21 860-535 Screw ........................................................2

22 800-266 Hose (not shown) .....................................1

800-590A Low rider cart

(not shown, see separate listing)

---------- Low rider siphon assembly

(not shown, see separate listing)

La page charge ...

Titan 840IX Le manuel du propriétaire

Marque: Titan

Modèle: 840IX

Catégorie: Pulvérisateur de peinture

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Titan 840IX Owner's manual
español: Titan 840IX El manual del propietario

Titan 840IX Le manuel du propriétaire

Titan 840IX Le manuel du propriétaire

dans d''autres langues

Documents connexes