Kichler Lighting 44065NI Manuel utilisateur

Taper
Manuel utilisateur
Date Issued: 08/30/17 IS-44065-US
Were here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
1) Pass fixture wire through desired amount of stems and screw
stems together using supplied short threaded tubes.
NOTE: Thread locking compound must be applied to all stem
threads as noted with arrow symbol to prevent accidental
rotation of fixture during cleaning, relamping, etc.
NOTE: Thread locking compound must be applied to all stem
threads as noted with symbol to prevent accidental rotation of
fixture during cleaning, relamping, etc.
2) Pass fixture wire through end of swivel without threaded pipe.
Thread that end of swivel onto end of last stem.
NOTE direction of swivel in accordance with ceiling.
3) Pass fixture wire through hole in canopy. Pass threaded pipe
on end of swivel up through hole in canopy.
4) Pass fixture wire through hole in lockwasher. Thread lock-
washer onto end of threaded pipe protruding from inside
canopy.
5) Pass fixture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
6) Find the appropriate threaded holes on mounting strap. As-
semble mounting screws into threaded holes.
7) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
8) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture ground
wire to outlet box ground wire with wire connector. (Not pro-
vided.) After following the above steps. Never connect ground
wire to black or white power supply wires.
9) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
10) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy. NOTE: Be certain wires do not get
pinched between mounting strap and canopy.
11) Use ball knobs and lockwashers to secure canopy. Tighten to
secure.
12) Carefully raise glass to the fixture. Slip the smaller opening
over the socket and fit the glass against the socket cover.
13) Thread socket ring onto socket. Tighten socket ring to
secure glass in place. (DO NOT over tighten.)
14) Insert recommended bulb. (Not supplied)
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
MOUNTING SCREWS
VIS DE MONTAGE
OUTLET BOX
BOÎTE À PRISES
WIRE CONNECTORS
CONNECTEURS DE FIL
STRAP MOUNTING SCREW
VIS DE L'ÉTRIER DE MONTAGE
MOUNTING STRAP
ÉTRIER DE MONTAGE
HEXNUT
ÉCROU HEXAGONAL
LOCKWASHER
RONDELLE DE BLOCAGE
CANOPY
COUVERCLE
LOCK-UP KNOBS
BOULES DE BLOCAGE
LOCKWASHERS
RONDELLE DE BLOCAGE
SWIVEL
PIVOT
GLASS
VERRE
SOCKET RING
ANNEAU DE DOUILLE
BULB (NOT INCLUDED)
AMPOULE (PAS INCLUSE)
SOCKET
DOUILLE
SOCKET
COVER
COUVERCLE DE DOUILLE
STEM(S)
TIGE
THREADED PIPE
TUBE FIL
Date Issued: 08/30/17 IS-44065-US
Estamos aquí para ayudarle 866-558-5706
Horario: Lunes-Viernes 9am a 5pm EST (hora oficial del este)
1) Pase el cable del accesorio a través de la cantidad deseada
de tallos y tornillo se unen utilizando tubos roscados cortos
suministrados. NOTA: El compuesto de bloqueo de rosca
debe aplicarse a todos los hilos del vástago como se indica
con el símbolo de flecha para evitar la rotación accidental del
aparato durante la limpieza, relamping, etc.
2) Pasar del luminario al alambre a través del extremo del
eslabón giratorio sin tubo. Ese extremo del eslabón giratorio
en el extremo del último vástago del hilo de rosca.
NOTA dirección de giro de conformidad con el techo.
3) Pasar del luminario a través del orificio en el pabellón. Pasar
tubo roscado en el extremo del eslabón giratorio a través del
orificio en el pabellón.
4) Pasar el cable a través del agujero en la arandela de se-
guridad. Tornillo de la arandela de seguridad en el extremo
roscado del tubo desde el interior de la cubierta.
5) Pasar del luminario a través del agujero de la tuerca hexago-
nal. Tuerca hexagonal rosca al extremo del tubo roscado.
6) Enrosque un tubo roscado pequeño en el extremo de cada
anillo pequeño.
7) Acople la abrazadera de montaje a la caja de salida. (No se
provee tornillos). La abrazadera de montaje se puede ajustar
para acomodar la posición del artefacto.
8) Instrucciones para poner a tierra: (Ver Ilustraciones A o B).
A) En artefactos donde se suministra la abrazadera de
montaje con un agujero y dos depresiones onduladas.
Envuelva el conductor de tierra de la caja de salida
alrededor del tornillo de tierra verde y atornille en el
agujero.
B) En artefactos donde se suministra una arandela
cóncava. Fije el conductor de tierra de la caja de salida
debajo de la arandela cóncava y el tornillo de tierra
verde y enrosque en la abrazadera de montaje.
Si se suministra el artefacto con conductor de tierra. Conecte
el conductor de tierra del artefacto al conductor de tierra de
la caja de salida con conector de tierra después de seguir los
pasos anteriores. Nunca conecte el conductor de tierra a los
alambres de alimentación eléctrica negros o blancos.
9) Haga las conexiones de los alambres. Re érase a la tabla de
abajo para realizar las conexiones correctas de los cables.
10) Empuje la fijación al techo, pasando cuidadosamente los
tornillos de montaje a través de agujeros en el dosel. NOTA:
Asegúrese de que los cables no queden correa de montaje y
dosel.
11) Utilice las perillas de bolas y las arandelas de seguridad para
asegurar el dosel. Apriete para asegurar.
12) Levante con cuidado el cristal al aparato. Deslice la abertura
más pequeña sobre el zócalo y ajuste el vidrio contra la cubi-
erta del zócalo.
13) Introduzca el casquillo en el casquillo. Apriete el anillo
seguro en su lugar (NO apriete demasiado).
14) Inserte la bombilla recomendada (No incluido).
PRECAUCIÓN – RIESGO DE DESCARGA ELÉCTRICA –
Desconecte la electricidad en el panel principal del interruptor
automático o caja principal de fusibles antes de comenzar y
durante la instalación.
ARANDELA
CONCAVA
TIERRA DE LA
CAJA DE SALIDA
TORNILLO DE TIERRA,
VERDE
DEPRESIONES
TIERRA
ARTEFACTO
CONECTOR DE ALAMBRE
TIERRA DE LA
CAJA DE SALIDA
TORNILLO DE TIERRA,
VERDE
TIERRA
ARTEFACTO
A
B
Conectar el alambre de
suministro negro o rojo al
Conectar el alambre de
suministro blanco al
Negro Blanco
*Cordon paralelo (redondo y liso)
*Cordon paralelo (cuadrado y estriado)
Claro, marrón, amarillio o negro
sin hebra identificadora
Claro, marrón, amarillio o negro
con hebra identificadora
Alambre aislado (diferente del verde)
con conductor de cobre
Alambre aislado (diferente del
verde) con conductor de plata
*Nota: Cuando se utiliza alambre paralelo
(SPT I y SPT II). El alambre neutro es de forma
cuadrada o estriada y el otro alambre será de
forma redonda o lisa. (Vea la ilustracíón).
Hilo Neutral
MOUNTING SCREWS
VIS DE MONTAGE
OUTLET BOX
BOÎTE À PRISES
WIRE CONNECTORS
CONNECTEURS DE FIL
STRAP MOUNTING SCREW
VIS DE LTRIER DE MONTAGE
MOUNTING STRAP
ÉTRIER DE MONTAGE
HEXNUT
ÉCROU HEXAGONAL
LOCKWASHER
RONDELLE DE BLOCAGE
CANOPY
COUVERCLE
LOCK-UP KNOBS
BOULES DE BLOCAGE
LOCKWASHERS
RONDELLE DE BLOCAGE
SWIVEL
PIVOT
GLASS
VERRE
SOCKET RING
ANNEAU DE DOUILLE
BULB (NOT INCLUDED)
AMPOULE (PAS INCLUSE)
SOCKET
DOUILLE
SOCKET
COVER
COUVERCLE DE DOUILLE
STEM(S)
TIGE
THREADED PIPE
TUBE FIL
  • Page 1 1
  • Page 2 2

Kichler Lighting 44065NI Manuel utilisateur

Taper
Manuel utilisateur