Hestan KRD364GD-NG Mode d'emploi

INDOOR COOKING

Dual-Fuel Range

KRD

Use & Care Manual

SAFETY DEFINITIONS

THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY OCCUR

AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT MINOR OR MODERATE INJURY MAY

OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.

THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR

PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS

WARNING.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE

INSTALLING OR USING YOUR APPLIANCE TO REDUCE THE RISK OF

FIRE, BURN HAZARD, OR OTHER INJURY. KEEP THIS MANUAL FOR

FUTURE REFERENCE.

CAUTION

NOTICE

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

1. Do not try and light any appliance.

2. Do not touch any electrical switch.

3. Do not use any phone in your building.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

5. If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.

HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

TIP OVER HAZARDTIP OVER HAZARD

A child or adult can tip over a range and be killed.

Check installation of the anti-tip device per the Installation Manual. Do

not operate the range without this device in place.

Check engagement of anti-tip device if range is moved, such as when

cleaning behind the unit.

To check engagement, carefully tip the range forward while pulling from the rear of the unit. The

range should not move more that 1 inch [2.5cm].

Failure to follow these instructions can result in death or serious burns to children and adults.

To reduce the risk of burns, do not move this appliance while hot.

1

EN

Message from HestanMessage from Hestan

Hestan’s award-winning culinary innovations and purpose-built features reinvented

the restaurant kitchen and redefined culinary experience in some of America’s most

acclaimed restaurants. Hestan now takes this performance from the back of the

house and puts it front and center in yours. Thoughtfully designed and meticulously

built, Hestan will serve you beautifully for years to come.

Hestan is the only residential brand born from the dreams and demands of

professional chefs. From ranges to refrigeration, every detail is designed to deliver

the performance and reliability expected in a restaurant – now available for you.

We appreciate you choosing Hestan, and we promise to deliver the very best to you.

Welcome to HestanWelcome to Hestan

3

EN

When properly cared for, your Hestan appliance will provide safe, reliable service for many years.

When using this appliance, basic safety practices must be followed as outlined below.

INSTALLER: Please leave these Installation Instructions with the owner.

OWNER: Please retain these Installation Instructions for future reference.

This range is designed for residential use only. It is NOT designed for installation in manufactured

(mobile) homes or recreational park trailers. Do NOT install this range outdoors.

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

ELECTRICAL SHOCK HAZARDELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing appliance. Before turning

power ON, be sure all controls are in the OFF position. Failure to do so can

result in electrical shock or death.

ELECTRICAL GROUNDINGELECTRICAL GROUNDING

This appliance must be grounded. Grounding reduces the risk of electric shock

in the event of a short circuit. Read the ELECTRICAL CONNECTIONS section of the Installation

Manual for complete instructions.

This appliance is equipped with a 4-prong grounding plug for your protection against shock hazard

and should be directly plugged into a properly grounded receptacle. Do not cut or remove the

grounding prong from this plug.

TABLE OF CONTENTS

3 SAFETY PRECAUTIONS - BEFORE YOU BEGIN

8 MODEL NUMBERS

9 RATING LABEL

9 REGULATORY / CODE REQUIREMENTS

10 GETTING STARTED WITH YOUR APPLIANCE

17 USING THE RANGETOP

19 USING THE GRIDDLE

(SOME MODELS)

20 USING THE OVEN

24 OVEN CONTROLS

44 ADDITIONAL ITEMS

44 CARE & MAINTENANCE

49 TROUBLESHOOTING GUIDE

50 PARTS LIST

50 SERVICE

51 LIMITED WARRANTY

4

EN

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONTINUED)

ELECTRICAL SUPPLYELECTRICAL SUPPLY

This appliance must be connected to a dedicated circuit, 240 VAC, Single Phase, 60 Hz, with a

current rating as shown in the model number listing on pg. 8. Have the installer show you where

the electric circuit breaker is located so you know how to shut off the power to this appliance. It is

the responsibility of the user to have the appliance connected by a licensed electrician in accordance

with all local codes, or in the absence of local codes, in accordance with the National Electrical Code.

Read the ELECTRICAL CONNECTIONS section of the Installation Manual for complete details.

GAS SUPPLYGAS SUPPLY

A gas shut-off valve must be located in an easily accessible location for servicing of the range. Make

sure all users of the range know where this shut-off is located, and how to shut off the gas.

The type of gas should be verified prior to installation and

operation of this appliance. It is the responsibility of the

user to have the appliance connected by a licensed plumber

in accordance with all local codes, or in the absence of local

codes, in accordance with the National Fuel Gas Code.

When connecting to LP gas, verify the tank is equipped

with its own high pressure regulator. The pressure of the

gas supplied to the appliance must be 11-14 inch WC [2.74-

3.48 kPa]. Consult the Installation Manual for details on gas

type, gas pressure, connection and leak testing instructions,

etc.

Read the GAS CONNECTIONS section of the Installation

Manual for complete details.

CONVERSION KITSCONVERSION KITS

In the event your Hestan appliance needs to be converted from NG to LP, or vice-versa, you will

need to contact Hestan Customer Service to arrange a service call. This conversion should only be

performed by a qualified technician.

HIGH ALTITUDE KITSHIGH ALTITUDE KITS

If you live in a high altitude area, 2,000 ft. [610 m] or more above sea level, your appliance may

require different orifices for proper combustion and performance. You will need to contact Hestan

Customer Service to arrange a service call. High Altitude kits must be installed by a qualified

technician. Please have your model and serial number information ready when you call.

BACKGUARDBACKGUARD

Your Hestan range is supplied at the factory with an Island Trim backguard. See Table 1 in the

APPENDIX section of the Installation Manual for other backguard options available from your

Hestan dealer, or visit www.hestanhome.com. Selection of the appropriate backguard depends on

the installation location and adjacent materials, and the type of vent hood to be used. Installation

instructions are included with the backguard kit. A LOW OR TALL BACKGUARD IS REQUIRED

WHEN INSTALLING THE RANGE AGAINST A COMBUSTIBLE SURFACE - THE ISLAND TRIM IS

NOT SUITABLE.

CAUTION

The top of the backguard serves as an exhaust for the oven when in operation, and as an exhaust vent

to remove heat from under the rangetop section of the range as well. DO NOT BLOCK or obstruct

the top of the backguard. DO NOT touch the top of the backguard during appliance operation as it

may get hot. Allow sufficient time to cool before touching or cleaning this area. DO NOT position

plastic or other heat-sensitive items nearby which could melt or burn.

GAS

SUPPLY

TO

APPLIANCE

SHUTOFF VALVE

IN OPEN POSITION

5

EN

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONTINUED)

VENTILATION REQUIREMENTSVENTILATION REQUIREMENTS

It is strongly recommended that this appliance be installed with a Hestan vent hood. Hestan vent

hoods have been matched up to the BTU output of the range. Due to the high heat output of this

range, it is very important that the hood and ductwork installation meets local building codes and is

installed by a qualified technician.

Do not use a down-draft style ventilation system.

Do not mount a microwave oven/ventilator combination above the range. These types of units do

not have sufficient airflow to remove the high heat output of this range and were not tested with

this type of appliance.

Consult the Installation Manual for further details.

CONSULT WITH YOUR HESTAN DEALER ON SELECTING THE APPROPRIATE

VENT HOOD FOR YOUR HESTAN APPLIANCE.

IN CASE OF POWER OUTAGEIN CASE OF POWER OUTAGE

All the control knobs must be in the OFF position to prevent unintended operation at power up. To

ensure customer safety in the event of a power failure, the range will display an error message when

the power is restored unless all the knobs are in the OFF position. Set all the knobs to OFF to clear

the error message.

DO NOT ATTEMPT TO USE THE RANGE DURING A PROLONGED POWER FAILURE. Although

the top burners can be manually lit, they should be used ONLY WHILE BEING ATTENDED BY THE

USER. On low burner settings, if the flame were to go out, a dangerous accumulation of gas could

result in an explosion.

CAUTION

CHILD SAFETYCHILD SAFETY

IT IS THE RESPONSIBILITY OF THE PARENTS OR GUARDIANS TO ENSURE CHILDREN ARE

INSTRUCTED IN THE SAFE USE OF THIS APPLIANCE. Do not allow children to use this appliance

without adult supervision. Do not allow children to play in or around the appliance, even when not

in use. Items of interest to children should not be stored in or on the appliance, in cabinets above, or

on the backguard of the appliance. Children climbing on the appliance could be seriously injured.

BURN HAZARD - All parts of the range can get very hot during operation. The oven door glass

and areas surrounding the door get very hot, especially during self-cleaning operations. Do not let

children touch the appliance while in operation. Failure to observe these instructions may result in

severe burns or injury.

TECHNICAL SAFETYTECHNICAL SAFETY

Installation and service on this appliance must be performed by a qualified appliance installer, or

a Hestan authorized service technician. Do not repair or replace any part of the appliance unless

specifically instructed to do so. Defective parts must only be replaced with genuine Hestan parts.

Contact Hestan Customer Service for inquiries or to arrange a service call.

The appliance must be disconnected from the power and gas supply during any service or

maintenance work.

Do not carry or lift the range by the oven handle. The range can only lifted from the sides.

6

EN

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONTINUED)

USER SAFETYUSER SAFETY

BURN HAZARD - All parts of the range can get very hot during operation. The oven door glass and

areas surrounding the door get very hot, especially during self-cleaning operations. Do not touch

the appliance while in operation. Failure to observe these instructions may result in severe burns

or injury. Use pot holders / gloves to protect yourself when placing food in the oven, adjusting the

racks, etc.

The upper broil element is housed behind a special glass panel, and the lower bake element is hidden

beneath the floor of the oven cavity. The convection element is hidden behind the fan at the rear of

the oven cavity. All these heating elements may be hot, even though they are not glowing. During or

after cooking, allow sufficient time for all surfaces to cool.

Use only dry or heat-resistant pot holders / gloves. Using moist or damp potholders can result in

steam burns. Do not substitute dish towels or similar items for potholders. These items could come

in contact with hot surfaces and ignite.

Avoid wearing loose-fitting garments or long sleeves while cooking. They could ignite. For personal

safety, wear proper apparel while using the appliance. Some synthetic fabrics are highly flammable

and should not be worn while cooking.

Open the oven door slowly to allow heat and steam to escape before placing or removing food from

the oven. Keep your face away from the opening to avoid injury.

For safety considerations, NEVER use this appliance as a space heater to heat or warm the room.

Doing so may result in carbon monoxide poisoning and overheating of the oven.

Do not use the oven as a storage space. The high temperatures could also ignite flammable objects

nearby.

NEVER cover any slots, holes, or passages in the oven bottom or cover an entire oven rack with

materials such as aluminum foil. Doing so blocks air flow through the oven and may cause carbon

monoxide poisoning. Aluminum foil linings may also trap heat, causing a fire hazard. Do not use

aluminum foil to line the surface burners. Doing so may result in a risk of electric shock, or fire.

Do not allow anyone to climb, stand, step on, lean against, or sit on any part of the appliance,

especially the oven door. This may result in damage to the appliance, or personal injury.

FIRE SAFETYFIRE SAFETY

To reduce the risk of a fire, do not leave surface burners unattended at high settings. Boil-overs could

smother the flames and igniter, which would allow un-burned gas to escape into the room, which

could result in an explosion.

Always turn on the ventilation hood when cooking. Clean vent hood grease filters frequently -

grease should not be allowed to accumulate on the fan or filters.

Use the appropriate pan size for the burner being used. For safety considerations, adjust the flame

size so they do not travel up the sides of the pan.

Keep the appliance area clear and free from combustible materials, gasoline, and other flammable

vapors and liquids. NEVER store flammable liquids and materials in, above, or on the range, or near

cooking surfaces. Do not obstruct the flow of combustion and ventilation air of the appliance.

ALWAYS have a working smoke detector near the kitchen.

ALWAYS have an appropriate dry-chemical fire extinguisher nearby. Smother fire or flames using

the lid of the utensil (pot or pan), a cookie sheet or metal tray. Then shut off the burner. Use an

7

EN

extinguisher, or baking soda if the fire is small and relatively contained. DO NOT USE WATER ON A

GREASE FIRE. Doing so may result in spreading the fire elsewhere.

NEVER pick up a flaming pan. You may spill the grease on yourself and be severely burned.

If accessible, turn off the ventilation hood during a fire, but do not reach through the flames to do

this.

In the event of personal clothing or hair catching fire, drop and roll immediately to smother the

flames. Seek medical attention if necessary.

Do not hang articles from any part of the appliance or place anything against the oven door. Some

fabrics are highly flammable and could ignite.

IF THE FLAMES DO NOT GO OUT - EVACUATE AND CALL THE FIRE

DEPARTMENT.

SAFETY DURING CLEANINGSAFETY DURING CLEANING

Only clean the appliance as directed in the CLEANING & MAINTENANCE section of this manual.

Do not use a steam cleaner to clean the oven or any part of the range. Steam could penetrate into

electrical components and cause a short circuit and/or shock hazard.

Do not use abrasive cleaners, hard objects such as brushes or scrapers, or sharp metal tools to clean

the door glass. Scratches could cause the glass to shatter.

Heavy food debris should be removed before running the self-clean cycle. Remove all oven racks,

broiler pans, utensils, temperature probes, etc. from the oven before self-clean. Removal of the left &

right ladder racks inside should also be done as they will discolor from the intense heat.

Do not rub, disturb or damage the cloth-braided door gasket. If the gasket is damaged, it will need to

be replaced.

Do not pour cold water onto hot surfaces inside the oven. The steam could cause serious burns. The

sudden temperature change could also distort the metal surfaces inside the oven resulting in cracks in

the enamel.

Use only a small toothbrush to clean the burner ports and igniter of the surface burners. Do not

insert sharp objects or scratch the burner ports.

Wait until the appliance is completely cool before using any aerosol-type cleaners. Many of these

cleaners use flammable propellants which could ignite in the presence of heat.

PROPER USAGEPROPER USAGE

Do not let food sit in the oven for more than one hour before or after cooking. Doing so may result

in food poisoning or illness.

Do not heat unopened containers (cans) in the oven. Pressure may build up causing the container to

explode, resulting in damage to the oven, or personal injury.

Always place the oven racks at the desired height before cooking. If the racks must be moved when

hot, use potholders to move them and use caution to avoid touching any heating elements.

Only certain types of glass, heatproof glass-ceramic, earthenware, or other glazed utensils are

suitable for use on the surface burners. However, these types of materials may break with

sudden temperature changes. Use only on low or medium heat settings, and according to their

manufacturers’ directions.

Bakeware, such as large casserole pans, cookie sheets, etc. should not be used on the surface burners.

Large griddle plates that span across 2 burners should be used with care and on medium to low flame

settings to avoid a build-up of heat which could distort the grates or the burner bowl.

Always position the handles of pot and pans so they do not extend over adjacent work areas or over

the edge of the rangetop. This is to avoid knocking over hot contents which could burn you, or

result in a fire.

Do not use pots or pans on the griddle (if equipped).

SAFETY PRECAUTIONS - BEFORE YOU BEGIN

(CONTINUED)

8

EN

MODEL NUMBERS

RANGE MODELSRANGE MODELS

MODEL NO.MODEL NO. DESCRIPTIONDESCRIPTION

CIRCUIT BREAKER CIRCUIT BREAKER

REQUIREDREQUIRED

KRD304-NG / -LP 30” DUAL-FUEL RANGE WITH 4 BURNERS 40 Amp

KRD365-NG / -LP 36” DUAL-FUEL RANGE WITH 5 BURNERS 40 Amp

KRD364GD-NG / -LP 36” DUAL-FUEL RANGE WITH 4 BURNERS & 12” GRIDDLE 40 Amp

KRD485GD-NG / -LP 48” DUAL-FUEL RANGE WITH 5 BURNERS, 2 OVENS, & 12”GRIDDLE 50 Amp

KRD484GD-NG / -LP 48” DUAL-FUEL RANGE WITH 4 BURNERS, 2 OVENS, & 24”GRIDDLE 50 Amp

KRD485GDKRD485GDKRD365KRD365

KRD304KRD304

KRD364GDKRD364GD

KRD484GDKRD484GD

9

EN

REGULATORY / CODE REQUIREMENTS

Installation of this cooking appliance must be made in accordance with local codes. In the absence

of local codes, this unit should be installed in accordance with the National Fuel Gas Code

ANSI

Z223.1/NFPA 54

, Natural Gas and Propane Installation code

CSA B149.1

, or Propane Storage and

Handling Code

B149.2

.

All Electrical Components must be electrically grounded in accordance with local codes or in the

absence of local codes with the National Electrical Code

ANSI/NFPA 70

, or Canadian Electrical code

CSA C22.1

.

STATE OF MASSACHUSETTS

Massachusetts requires all gas be installed using a plumber or gas fitter carrying the appropriate

Massachusetts license. All permanently installed natural gas or propane installations require a

T-handle type manual gas valve be installed in the gas supply line to this appliance. Flexible gas

connector must not be longer than 48” [1.2 m].

CALIFORNIA PROPOSITION 65 - WARNING

WARNINGWARNING This product can expose you to chemicals including carbon monoxide, which is

known to the State of California to cause birth defects or other reproductive harm.

For more information, go to www.P65Warnings.ca.gov.

RATING

LABEL

RATING LABEL

The rating label contains important information about your

Hestan appliance such as the model and serial number, gas type

and manifold pressure, electrical rating, the BTU rating for each

burner type, and the minimum installation clearances.

The rating label is located in one of two places, as shown in the

figures on this page.

If service is necessary, contact Hestan Customer Care with the

model and serial number information shown on the label.

RATING LABEL

10

EN

GETTING STARTED WITH YOUR APPLIANCE

COMPONENT IDENTIFICATIONCOMPONENT IDENTIFICATION

Use the images below to familiarize yourself with the various parts of the rangetop and oven.

KRD30, KRD36KRD30, KRD36

1. Island Trim Backguard (included)*

2. Sealed Dual-Flow Burner

3. Burner Grate

4. Griddle (GD models)

5. Control Knobs

6. Touch-screen Display

7. Main Oven

8. Oven Light Switch

9. Kick Plate

5

6

7

2

3

4

1

8

9

10

* Low or Tall Backguard ordered

separately.

MODEL KRD364GD SHOWN

Oven cavity of 30” range, 36”

range, main oven cavity of 48”

range

1. Temperature Probe Jack, oven

of 36” range

2. 6 Position Ladder Rack

3. Oven Rack (3 included)

4. Fan Cover

5. Broil Element

6. Bake Element (hidden)

7. Temperature Sensor

8. Interior Light (2)

9. Self-Clean Latch

10. Temperature Probe Jack, 30”

range, Main Oven of 48” range

11

EN

COMPONENT IDENTIFICATION (CONTINUED)COMPONENT IDENTIFICATION (CONTINUED)

KRD48KRD48

1. Island Trim Backguard (included)*

2. Griddle (GD models)

3. Sealed Dual-Flow Burner

4. Single Flow Power Burner

5. Burner Grate

6. Control Knobs

7. Oven Light Switch - Companion

Oven

8. Touch-screen Display - Companion

Oven

9. Companion Oven

10. Touch-screen Display - Main Oven

11. Main Oven

12. Oven Light Switch - Main Oven

13. Kick Plate

Companion Oven cavity of 48” range

1. 6 Position Ladder Rack

2. Oven Rack (3 included)

3. Fan Cover

4. Broil Element

5. Bake Element (hidden)

6. Temperature Sensor

7. Interior Light

1

2

3

4

5

6

7

8

9

11

12

13

10

1

3

4

6

7

2

5

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

MODEL KRD485GD SHOWN

12

EN

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

DUAL-FLOW DUAL-FLOW

BURNERBURNER

SINGLE-FLOW SINGLE-FLOW

BURNERBURNER

OVEN MODE OVEN MODE

SELECTORSELECTOR

OVEN OVEN

TEMPERATURETEMPERATURE

GRIDDLE GRIDDLE

TEMPERATURETEMPERATURE

ROTATE LEFTLEFT TO HI

TO IGNITE BURNER.

ADJUST FLAME AS

NEEDED. THERE ARE

3 DETENT POSITIONS

AT HI, LOW, AND HI

SIMMER FOR EASE OF

USE.

ROTATE LEFTLEFT TO

MAX TO IGNITE

BURNER. ADJUST

FLAME AS NEEDED.

THERE IS A DETENT

AT THE MAX

POSITION ONLY.

ROTATE

LEFTLEFT OR

RIGHTRIGHT TO SELECT

OVEN MODE

ROTATE LEFTLEFT OR

RIGHTRIGHT TO SELECT

OVEN TEMPERATURE

ROTATE

RIGHTRIGHT TO

SELECT GRIDDLE

TEMPERATURE

MARQUISE™ TOUCH CONTROL HANDLE

13

EN

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

OVEN RACKSOVEN RACKS

BURN HAZARD - To help prevent burns, never remove or reposition the oven racks when the oven is

in operation, or is cooling.

For safety considerations, NEVER cover any slots, holes, or passages in the oven bottom or cover an

entire oven rack with materials such as aluminum foil. Doing so blocks air flow through the oven

and may cause carbon monoxide poisoning. Aluminum foil linings may also trap heat, causing a fire

hazard.

PLACING THE OVEN RACKS

The oven features ladder racks on the left and right side of the oven with 6 positions. Choose

the rack position(s) that result in the best baking, roasting, etc. for your recipe. Rack position #3

(counting from the bottom-up) is the most popular position (vertical center location).

The main oven features racks with full-extension, ball-bearing

slides which require minimal maintenance. The companion oven

(model KRD48) has traditional wire racks.

ALWAYS REMOVE THE LADDER RACKS, OVEN RACKS, AND

ALL OTHER ITEMS FROM THE OVEN DURING THE SELF-

CLEANING CYCLE.

1

2

3

1. Do not extend the slides - it is easier to install the rack when

NOT extended.

While raising the front of the rack slightly, place the rear

hook onto the desired ladder rack, then slide the small tab

under the ladder as you flatten out the rack.

2. Continue sliding the rack back into the oven.

3. When you reach the front-most hook, slightly lift the rack

again to hook over the ladder.

Move the rack a few times in and out to ensure it is locked

into the ladders and will not detach.

14

EN

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

1. While raising the front of the rack

slightly, place the rear lower hooks

under the desired side ladder, then

slide the rack back approximately 5”

[13 cm].

2. Lower the rack until it is level.

3. Continue sliding the rack back into the

oven until it is fully inside.

PLACING RACKS - COMPANION OVEN

2

1

3

15

EN

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

SEALED BURNERSSEALED BURNERS

Ensure the sealed burner heads are properly installed and seated on the burner base as shown below.

There are notches on the burner base and cross ring to help with alignment. The outer burner head

features a long slot on the top of the head which aligns with the spark igniter. Assembly of the

single-flow burner head is similar.

FIRST TIME OPERATIONFIRST TIME OPERATION

Ensure there are no packaging materials inside the oven. Remove any labels or plastic film from the

outside of the appliance. Before using your oven for the first time, it will be necessary to run a bake

cycle to burn off any manufacturing oils and residues from the oven cavity. This may produce a little

smoke and some odor. This is normal and is typical of any new oven when first used. If the smell

is strong, remove persons and animals from the kitchen during this period. Open any windows to

further vent the odor from the room.

Install all the oven racks. Turn on your vent hood, and run the oven on BAKE at 500°F [260°C] for

1-1/2 hours. Allow to cool completely before attempting to cook.

DUAL-OVEN MODELSDUAL-OVEN MODELS

For dual-oven models, perform the same first-time process on the companion oven. This can be done

at the same time as the main oven.

BURNER

RING

BURNER

HEAD

BURNER

BASE

IGNITER

INNER

BURNER

HEAD

OUTER

BURNER

HEAD

BEAUTY

RING

CROSS

RING

BURNER

BASE

DUAL FLOW

BURNER

SINGLE FLOW

BURNER

16

EN

GETTING STARTED WITH YOUR APPLIANCE

(CONTINUED)

BURNER HEADSBURNER HEADS

If the burner head is not properly positioned, one or more of the following issues may occur:

• Flames too high

• Flames shoot out of the burners

• Burners do not ignite

• Flames are uneven

• Burner emits a gas odor

BURN HAZARD - To prevent burns, do not touch the burner heads or cooking grates when hot.

Allow to cool completely. To prevent flare-ups, do not use the burner without all the burner heads in

place and properly positioned. Do not use aluminum foil to line the surface burners. Doing so may

result in a risk of electric shock, or fire.

BURNER GRATESBURNER GRATES

See image for proper placement

of the burner grates. There are

small round embosses at the

front and rear of the burner

bowl to help align the grates

and keep them in position

relative to one-another.

GRIDDLE PLATEGRIDDLE PLATE

(GD models)

See image for proper placement of

the Griddle Plate and Grease Tray.

The plate is made of stainless-steel

and requires no seasoning. The

grease tray has a non-stick coating

for easy cleaning.

Always remove the cover before

cooking on your griddle.

GREASE

TRAY

GRIDDLE

PLATE

COVER

17

EN

USING THE RANGETOP

BURNER CONTROL KNOBSBURNER CONTROL KNOBS

Each sealed burner has its own control knob. The symbol below each knob indicates which burner is

controlled by each knob. Push and turn LEFT (counter-clockwise) to HI to ignite the flame, then turn

to the desired flame setting.

BURNER TYPES & OUTPUTBURNER TYPES & OUTPUT

This table below indicates

the type and output of

each sealed burner. Dual-

flow burners have an inner

and outer row of ports,

with a simmer function.

The single-flow burner

(some models) is similar to

a commercial burner and

features very high output,

and a low, but no simmer

function.

RE-IGNITIONRE-IGNITION

Each sealed burner has its own electronic spark-ignition module with flame-sensing technology and

automatic re-ignition capability. If any burner should blow out, the igniter automatically re-lights the

burner.

Each burner should light in less than 4 seconds. Once lit, the sparking will stop. On very low simmer,

an occasional sparking may occur. This is usually due to a breeze in the room. If an igniter continues

to spark even with a flame present, there could be an electrical wiring issue, or some other problem.

See the TROUBLESHOOTING section of this manual for more information.

DO NOT touch the burner or the igniters while sparking is occurring. A shock hazard or burns could

occur.

MANUAL LIGHTING / POWER FAILUREMANUAL LIGHTING / POWER FAILURE

THE OVEN AND GRIDDLE CANNOT BE USED DURING A POWER FAILURE.

Each sealed burner can be manually lit in the event of a power failure. It is necessary to light each

burner individually.

If a power failure occurs WHILE you are using the sealed burners, turn all the knobs to the OFF

position - then light manually with a match or fireplace lighter.

Position the match or fireplace lighter at the port nearest the igniter, then turn the knob to HI until

the flame is lit. Wait until the flame has lit all the way around the burner before adjusting the knob

to LOW or SIMMER.

IF YOU SMELL GAS, turn all control knobs to OFF - check the precautions listed in the SAFETY

section of this manual.

DUAL-FLOW

(FRONT)

OUTPUT

(BTU/hr)

DUAL-FLOW

(REAR)

OUTPUT

(BTU/hr)

SINGLE

GRIDDLE

FLOW

OUTPUT

(BTU/hr)

HI

23000

HI

15500

MAX

30000

LOW

4200

LOW

4200

LOW

4200

15000

GRIDDLE 15000

SIMMER HI

1500

SIMMER HI

1500

SIMMER LOW

500

SIMMER LOW

500

DUAL-FLOW

(FRONT)

OUTPUT

(BTU/hr)

DUAL-FLOW

(REAR)

OUTPUT

(BTU/hr)

SINGLE

FLOW

OUTPUT

(BTU/hr)

HI

23000

HI

15500

MAX

22000

LOW

4200

LOW

4200

LOW

SIMMER HI

1500

SIMMER HI

1500

SIMMER LOW

600

SIMMER LOW

600

BURNER OUTPUT - PROPANE

4200

BURNER OUTPUT - NATURAL GAS

18

EN

USING THE RANGETOP

(CONTINUED)

FLAME HEIGHTFLAME HEIGHT

Proper flame height depends on the size of the pan being used, and the amount of food or liquid

in the pan. In other words, don’t use a small pan over a large flame. For safety reasons, control the

flame height so that it doesn’t go beyond, or curl up the sides of your pot or pan. This behavior

results in poor heating of the contents of the pan, burnt food on the sides of the pan, wasted fuel,

etc.

Use a low or medium flame on items that heat slowly, such as glass-ceramic pots.

FLAME CHARACTERISTICSFLAME CHARACTERISTICS

Light blue flame - Natural gas normal flame

Light blue flame with yellow tips - LP gas normal flame

Yellow flame - Needs adjustment

If the flame is mostly or completely yellow, check the position of the burner heads again for proper

installation, and/or review the FINAL SETUP section of the installation manual for more details.

HOW TO USE YOUR RANGETOPHOW TO USE YOUR RANGETOP

DUAL FLOW BURNERSDUAL FLOW BURNERS

The benefit of the dual-flow burner is the amount of control and precision the burners give you,

allowing for the best results possible.

Simmer-Low is ideal for heating delicate foods without having the fear of burning, scalding, or

boiling over. Some suggestions include:

• Melting chocolate

• Heating milk or cream

• Melting sugar

• Slow cooking or braising

SINGLE FLOW BURNER (some models)SINGLE FLOW BURNER (some models)

Ideal Uses:

• Searing

• Boiling water

• Large stock pots – will allow for even heat distribution under larger surface areas

Wok Cooking: We suggest a 14-16 inch [36-41 cm] wok for the best results.

COOKWARE RECOMMENDATIONSCOOKWARE RECOMMENDATIONS

As previously stated on page 7 of the SAFETY PRECAUTIONS section of this manual, bakeware, such

as large casserole pans, cookie sheets, etc. should not be used on the surface burners. Large griddle

plates that span across 2 burners should be used with care and on medium to low flame settings to

avoid a build-up of heat which could distort the grates or the burner bowl.

La page charge ...

Hestan KRD364GD-NG Mode d'emploi

Hestan KRD364GD-NG Mode d'emploi

dans d''autres langues

Documents connexes