3-810-322-11 (1)
1995 by Sony Corporation
Operating Instructions
Mode d’emploi
Manual de instrucciones
MMMMM
CDP-XE500
CDP-XE300
CDP-XE200
2
EN
WARNING
To prevent fire or shock
hazard, do not expose the unit
to rain or moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
The laser component in this product
is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as a CLASS 1
LASER product. The CLASS 1 LASER
PRODUCT MARKING is located on the
rear exterior.
The following caution label is located
inside of the unit.
• The player is not disconnected from
the AC power source (mains) as long
as it is connected to the wall outlet,
even if the player itself has been
turned off.
• If you are not going to use the player
for a long time, be sure to disconnect
the player from the wall outlet. To
disconnect the AC power cord (mains
lead), grasp the plug itself; never pull
the cord.
• AC power cord must be changed only
at the qualified service shop.
On placement
• Place the player in a location with
adequate ventilation to prevent heat
build-up in the player.
• Do not place the player on a soft
surface such as a rug that might block
the ventilation holes on the bottom.
• Do not place the player in a location
near heat sources, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
On operation
• If the player is brought directly from a
cold to a warm location, or is placed in
a very damp room, moisture may
condense on the lenses inside the
player. Should this occur, the player
may not operate properly. In this case,
remove the disc and leave the player
turned on for about an hour until the
moisture evaporates.
On adjusting volume
• Do not turn up the volume while
listening to a portion with very low
level inputs or no audio signals. If you
do, the speakers may be damaged
when a peak level portion is played.
On cleaning
• Clean the cabinet, panel and controls
with a soft cloth slightly moistened
with a mild detergent solution. Do not
use any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine.
If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.
For the customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK,
DO NOT USE THIS POLARIZED AC
PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
If the plug supplied with this equipment
has a detachable fuse cover, be sure to
attach the fuse cover after you change
the fuse. Never use the plug without the
fuse cover. If you should lose the fuse
cover, please contact your nearest Sony
service station.
IMPORTANT
If the plug supplied is not suitable for the
socket outlets in your home, it should be
cut off and an appropriate plug fitted in
accordance with the following
instructions.
The wires in this mains lead are coloured
in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains
lead of this apparatus may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be
connected to the terminal which is
marked with the letter N or coloured
black. The wire which is coloured brown
must be connected to the terminal which
is marked with the letter L or coloured
red. Do not connect either wire to the
earth terminal in the plug which is
marked by the letter E or by the safety
earth symbol or coloured green or
green-and-yellow.
WARNING
To prevent shock hazard, do not insert
the plug cut off from the mains lead into
a socket outlet. This plug cannot be used
and should be destroyed.
NOTICE FOR CUSTOMERS IN THE
UNITED KINGDOM
A moulded plug complying with BS
1363 is fitted to this equipment for your
safety and convenience.
Should the fuse in the plug supplied
need to be replaced, a 5 AMP fuse
approved by ASTA or BSI to BS 1362,
(i.e. marked with or mark) must be
used.
Precautions
On safety
• Caution — The use of optical
instruments with this product will
increase eye hazard.
• Should any solid object or liquid fall
into the cabinet, unplug the player and
have it checked by qualified personnel
before operating it any further.
On power sources
• Before operating the player, check that
the operating voltage of the player is
identical with your local power
supply. The operating voltage is
indicated on the nameplate at the rear
of the player.
Getting Started
3
EN
Getting Started
Unpacking........................................................................................................ 4
Hooking Up the System................................................................................. 4
Playing a CD........................................................................................................ 6
Playing CDs
Using the Display ........................................................................................... 7
Locating a Specific Track or a Particular Point in a Track ........................ 8
Playing Tracks Repeatedly ............................................................................ 8
Playing in Random Order (Shuffle Play) ....................................................9
Creating Your Own Program (Program Play)............................................ 9
Recording From CDs
Recording Your Own Program...................................................................11
Recording a CD by Specifying Tape Length (Time Edit)........................12
Fading In or Out............................................................................................13
Adjusting the Recording Level (Peak Search) ..........................................14
Additional Information
Notes on CDs.................................................................................................14
Troubleshooting............................................................................................15
Specifications .................................................................................................15
Index
Index ...............................................................................................................16
TABLE OF CONTENTS
Welcome!
Thank you for purchasing the Sony
Compact Disc Player. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
About This Manual
The instructions in this manual are for
models CDP-XE500, CDP-XE300 and
CDP-XE200. The CDP-XE500 is the
model used for illustration purposes.
Any difference in operation is clearly
indicated in the text, for example, “CDP-
XE500 only.”
Conventions
• Instructions in this manual describe
the controls on the player.
You can also use the controls on the
remote if they have the same or
similar names as those on the player.
In the instructions, the buttons on the
remote are indicated in parentheses.
• The following icons are used in this
manual:
Indicates that you can do the
task using the remote.
(Note that the CDP-XE200
cannot do the tasks marked
with this icon.)
Indicates hints and tips for
making the task easier.
Getting Started
4
EN
Unpacking
Check that you received the following items:
• Audio connecting cord (1)
• Remote commander (remote) (except for CDP-
XE200) (1)
• Sony SUM-3 (NS) batteries (except for CDP-XE200) (2)
Inserting batteries into the remote (except
for CDP-XE200)
You can control the player using the supplied remote.
Insert two size AA (R6) batteries by matching the +
and – on the batteries. When using the remote, point it
at the remote sensor g on the player.
Hooking Up the System
Overview
This section describes how to hook up the CD player to
an amplifier. Be sure to turn off the power of each
component before making the connections.
Getting Started
White
(L)
Red
(R)
White
(L)
Red
(R)
What cords will I need?
Audio cord (supplied) (1)
Hookups
When connecting an audio cord, be sure to match the
color-coded cord to the appropriate jacks on the
components: Red (right) to Red and White (left) to
White. Be sure to make connections firmly to avoid
hum and noise.
Getting Started
CD player
Audio input
(L)
: Signal flow
Amplifier
To an AC outlet
To an AC outlet
Audio input
(R)
LINE OUT
(R)
LINE OUT
(L)
AmplifierCD player
When to replace batteries
With normal use, the batteries should last for about six
months. When the remote no longer operates the player,
replace all the batteries with new ones.
Notes
• Do not leave the remote near an extremely hot or humid
place.
• Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
• If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
Getting Started
5
EN
Getting Started
You can adjust the output level to the amplifier
(CDP-XE500 and CDP-XE300 only)
Press LINE OUT LEVEL +/– on the remote. You can
reduce the output level up to –20 dB.
When you reduce the output level, appears in the
display.
When you turn off the player, the output level
automatically returns to the maximum level.
• If you have a digital component such as a digital
amplifier, D/A converter, DAT or MD (CDP-XE500 only)
Connect the component via the DIGITAL OUT (OPTICAL)
connector using the optical cable (not supplied). Take off
the cap and plug in the optical cable.
Note that you cannot use the following functions when
making this connection:
• Fading in or out (see page 13)
• Time Fade (see page 13)
• Adjusting the output level using the LINE OUT LEVEL
+/– buttons on the remote (see above)
Setting the voltage selector (except for
European, Canadian and Australian models)
Check that the voltage selector on the rear panel of the
player is set to the local power line voltage. If not, set
the selector to the correct position using a screwdriver
before connecting the AC power cord to a wall outlet.
Connecting the AC power cord
Connect the AC power cord to a wall outlet.
Where do I go next?
Now you’re ready to use your player.
If you aren’t familiar with how to play CDs, go to the section
“Playing a CD” on page 6.
Then, go to the following sections for other operations.
POC-15
Optical cable (not supplied)
Digital component
CD player
Note
When you connect via the DIGITAL OUT (OPTICAL)
connector, noise may occur when you play CD software other
than music, such as a CD-ROM.
Basic Operations
6
EN
Turn on the amplifier and select the CD player position so that
you can listen to the sound from this player.
Press POWER to turn on the player.
Press § OPEN/CLOSE,
and place a disc on the
disc tray.
Press ·.
The disc tray closes and the player plays all the tracks once
(Continuous Play).
Adjust the volume on the amplifier.
To stop playback
Press p.
1
2
3
Playing a CD
• See pages 4 – 5 for the hookup
information.
To
Pause
Resume play after pause
Go to the next track
Go back to the preceding track
Stop play and remove the CD
You need to
Press P
Press P or ·
Turn ≠ AMS ± clockwise
Turn ≠ AMS ±
counterclockwise
Press § OPEN/CLOSE
4
If you turn on the player with
a CD in the tray
You can start playing
automatically from the
beginning of the CD. If you
connect a commercially
available timer, you can start
playing the CD at any time
you want.
You can adjust the output
level with the LINE OUT LEVEL
+/– on the remote (CDP-XE500
and CDP-XE300 only) Z
You can adjust the
headphones volume on the
remote (CDP-XE500 only) Z
Connect the headphones to
the PHONES jack and adjust
the volume with the LINE
OUT LEVEL +/– on the
remote.
2 3 4
Connect the
headphones.*
With the label side up
*CDP-XE500 only
Playing CDs
7
EN
Playing CDs
Using the Display
You can check information about the disc using the
display.
• CDP-XE500
Display information while playing a disc
While playing a disc, the display shows the current
track number, playing time and the music calendar.
Playing CDs
TIME
• CDP-XE300 and CDP-XE200
TIME
Music calendar
Current track
number
Playing time
The track numbers in the music calendar disappear
after they are played.
Checking the remaining time
Each time you press TIME while playing a disc, the
display changes as shown in the chart below.
Playing time and
number of the
current track
Press
Remaining time on
the current track
Remaining time on
the disc
Press
If the track number exceeds 68,
“– – . – –” appears instead of the
remaining time.
If the remaining time exceeds 100
minutes in Program Play mode,
“– – . – –” appears instead of the
remaining time.
Press
Checking the total number and playing
time of the tracks
Press TIME before you start playing.
The display shows the total number of tracks, total
playing time and music calendar.
Music calendar
Total number of
tracks
Total playing time
While in Shuffle Play mode (“SHUFFLE” appears in
the display; see page 9), a one-second access time blank
is added between each track. This increase is
automatically added to the total playing time in the
display.
The information also appears when you press
§ OPEN/CLOSE to close the disc tray.
Playing CDs
8
EN
Locating a Specific Track or a
Particular Point in a Track
You can quickly locate any track while playing a disc
using the AMS (Automatic Music Sensor) on the player
or number buttons on the remote.
You can also locate a particular point in a track while
playing a disc.
When you directly locate a track numbered over 10
when using the remote (except for CDP-XE200)
Press >10 first, then the corresponding number buttons.
To enter “0,” use button 10.
Example: To play track number 30
Press >10 first, then 3 and 10.
You can extend the playing time during Music Scan
Press MUSIC SCAN repeatedly until the playing time
you want (10, 20 or 30) appears in the display. Each time
you press the button, the playing time changes cyclically.
Note
If “ ” appears in the display, the disc has reached the end
while you were pressing ). Press 0 or turn ≠ AMS ±
counterclockwise to go back.
·MUSIC SCAN (CDP-XE500
only)
0 / )
≠ A M S ±
Number
buttons
>10
= / +
0 / )
(except for CDP-
XE200)
To locate
The next or
succeeding tracks
The current or
preceding tracks
A specific track
directly
By scanning each
track for 10 seconds
(Music Scan) (CDP-
XE500 only)
A point while
monitoring the sound
A point quickly by
observing the display
during pause
You need to
Turn ≠ AMS ± clockwise until
you find the track. When using the
remote, press + repeatedly until
you find the track.
Turn ≠ AMS ± counterclockwise
until you find the track. When using
the remote, press = repeatedly until
you find the track.
Turn ≠ AMS ± until you find the
track number you want appears in the
display. When using the remote, press
number button of the track (except for
CDP-XE200).
Press MUSIC SCAN. When you find
the track you want, press · to start
playing the track.
) (forward) or 0 (backward) and
hold down until you find the point
) (forward) or 0 (backward) and
hold down until you find the point.
You will not hear the sound during the
operation.
Playing Tracks Repeatedly
You can play tracks repeatedly in any play mode.
• CDP-XE500
REPEAT
• CDP-XE300 and CDP-XE200
REPEAT
Press REPEAT while playing a disc.
“REPEAT” appears in the display. The player repeats
the tracks as follows:
When the disc is played in
Continuous Play (page 6)
Shuffle Play (page 9)
Program Play (page 9)
To cancel Repeat Play
Press REPEAT repeatedly until “REPEAT” disappears from
the display.
The player repeats
All the tracks
All the tracks in random
orders
The same program
Playing CDs
9
EN
Playing CDs
Creating Your Own Program
(Program Play)
You can arrange the order of the tracks on a disc and
create your own program. The program can contain up
to 24 tracks.
Repeating the current track
You can repeat only the current track in any playmode.
While the track you want is being played, press
REPEAT repeatedly until “REPEAT 1” appears in the
display.
Playing in Random Order
(Shuffle Play)
You can have the player “shuffle” tracks and play in a
random order.
• CDP-XE500
• CDP-XE300 and CDP-XE200
• CDP-XE500
CHECK
CLEAR
≠ A M S ±
·
PLAYMODE
• CDP-XE300 and CDP-XE200
·
PLAYMODE
1 Press PLAYMODE repeatedly until “SHUFFLE”
appears in the display.
When using the remote, press SHUFFLE.
2 Press · to start Shuffle Play.
The indication appears while the player is
“shuffling” the tracks.
To cancel Shuffle Play
Press PLAYMODE twice.
When using the remote, press CONTINUE (except for CDP-
XE200).
You can start Shuffle Play while playing
Press PLAYMODE repeatedly until “SHUFFLE” appears
in the display. When using the remote, press SHUFFLE
(except for CDP-XE200). Shuffle Play starts from the
current track.
·
p
ENTER
CHECK
CLEAR
≠ A M S ±
ENTER
·
p
PLAYMODE
PLAYMODE
Creating a program on the player
1 Press PLAYMODE repeatedly until “PROGRAM”
appears in the display before you start playing.
2 Turn ≠ AMS ± until the track number you
want appears in the display.
The total playing time and the track numbers
being programmed are flashing in the display.
Track numbers being
programmed
(Continued)
Total playing time
Playing CDs
10
EN
3 Press ENTER to select the track.
Creating a program using the remote
(except for CDP-XE200) Z
PROGRAM
CLEAR
1 Press PROGRAM before you start playing.
“PROGRAM” appears in the display.
2 Press number buttons of the tracks you want to
program in the order you want.
Example: To program the tracks 2, 8 and 5.
Press number buttons in the order 2, 8
and 5.
Number buttons
CHECK
>10
Last programmed track Playing order
After one second
Total playing time
If you’ve made a mistake
Press CLEAR, then repeat Steps 2 and 3.
4 Repeat Steps 2 and 3 to program the tracks in the
order you want.
5 Press · to start Program Play.
To cancel Program Play
Press PLAYMODE.
When tracks, which aren’t numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
The program remains even after the Program Play
ends
When you press ·, you can play the same program
again.
Notes
• The total playing time doesn’t appear in the display when it
exceeds 100 minutes.
• “FULL” appears in the display when you try to add a track
to a program which already contains 24 tracks.
(
Last programmed track
Playing order
After one second
Total playing time
To select a track with a number over 10
Use >10 button (see page 8).
If you’ve made a mistake
Press CLEAR, then press the correct track number.
3 Press ( to start Program Play.
To cancel Program Play
Press CONTINUE.
When tracks, which aren’t numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
Programmed tracks
Programmed tracks
Playing CDs
11
EN
Playing CDs
The program remains even after the Program Play
ends
When you press (, you can play the same program
again.
You can check the total playing time while
programming using the remote (Program Edit)
To select a track, press = or + and check the total
playing time. Then press PROGRAM to confirm your
selection.
Notes
• The total playing time doesn’t appear in the display when it
exceeds 100 minutes.
• “FULL” appears in the display when you try to add a track
to a program which already contains 24 tracks.
Checking the track order
You can check your program before or after you start
playing.
Press CHECK.
Each time you press this button, the display shows the
track number in the programmed order. After the last
track in the program, the display shows “End” and
returns to the original display. If you check the order
after you start playing, the display shows only the
remaining track numbers.
Changing the track order
You can change your program before you start playing.
To
Erase a track
Erase the last track in the
program
Add tracks to the end of the
program
Change the whole program
completely
You need to
Press CHECK until the track
you don’t want appears in
the display, then press
CLEAR
Press CLEAR. Each time you
press the button, the last
track will be cleared.
Turn ≠ AMS ± until
track number you want to
add appears, then press
ENTER.
When using the remote,
press the number button of
the tracks to be added
(except for CDP-XE200).
Press p (stop). Create a new
program following the
programming procedure.
Recording from CDs
Recording Your Own Program
You can record the program you’ve created on a tape,
DAT or MD. The program can contain up to 24 tracks.
By inserting a pause during programming, you can
divide the program into two for recording on both
sides of a tape.
• CDP-XE500
• CDP-XE300 and CDP-XE200
Playing CDs
≠ A M S ±ENTER
· P
PLAYMODE
≠ A M S ±ENTER
PLAYMODE
·
P
1 Create your program (for side A when recording
on a tape) while checking the total playing time
indicated in the display.
Follow Steps 1 to 4 in “Creating a program on the
player” on page 9 or Steps 1 and 2 in “Creating a
program using the remote” on page 10.
The indication appears in the display.
2 When you record on both sides of the tape, press
P to insert a pause.
The “P” and indications appear in the display
and the playing time is reset to “0.00.”
When you record on one side of the tape or on a
DAT or MD, skip this step and go to Step 4.
A pause is counted as one track
You can program up to 23 tracks when you insert a
pause.
3 Repeat Step 1 to create the program for side B.
4 Start recording on the deck and then press · on
the player.
When you record on both sides of the tape, the
player pauses at the end of the program for side A.
5 When you record on side B, reverse the tape and
press · or P on the player to resume playing.
Recording From CDs
12
EN
To check and change your program
See page 11.
The indication appears while checking the program
for side A and while checking the program for side
B.
When tracks, which aren’t numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
Recording a CD by Specifying
Tape Length (Time Edit)
(CDP-XE500 only)
You can have the player create a program that will fit
the length of the tape.
The player automatically creates a program, keeping
the original order of the disc.
The program can contain up to 24 tracks (a pause
inserted between tracks is counted as one track).
Note that tracks whose numbers are over 24 cannot be
programmed automatically.
EDIT/TIME FADE
0 / )
·
4 When you record on both sides of the tape, press
EDIT/TIME FADE again.
The player inserts a pause, then creates the
program for side B. The display shows the
programmed tracks.
When you record on one side of the tape or on a
DAT or MD, skip this step.
5 Start recording on the deck and then press · on
the player.
When you record on both sides of the tape, the
player pauses at the end of the program for side A.
6 When you record on side B, reverse the tape and
press · or P on the player to resume playing.
To cancel Time Edit
Press PLAYMODE until “SHUFFLE” and “PROGRAM”
disappear from the display.
When using the remote, press CONTINUE.
You can program the tracks you want in advance
Select the tracks before doing the above procedure. The
player creates a program from the remaining tracks. In
this case, you cannot select “HALF” to specify the tape
length.
You can freely specify the tape length
Set the tape length using ≠ AMS ±.
Example: When the tape length of one side is 30 minutes
and 15 seconds
1 To set the minutes, turn ≠ AMS ± until
“30” appears in the display, then press
ENTER .
2 To set the seconds, turn ≠ AMS ± until
“15” appears in the display, then press
ENTER .
When tracks, which aren’t numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
To check and change your program
See page 11.
1 Press EDIT/TIME FADE before you start playing
until EDIT appears and “A” in the indication
flashes in the display.
2 Press 0 or ) to specify the tape length.
Each time you press these buttons, the display
changes as shown below, with the tape length of
one side following each indication.
n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - - .- - N
(23.00) (27.00) (30.00) (37.00) (45.00)
When you select “HALF”
The player sets the program of each side to a half of the
total playing time of the disc. Note that you cannot select
“HALF” when the disc has more than 24 tracks.
3 Press EDIT/TIME FADE to have the player create
the program.
The display shows the tracks to be recorded. “B” in
the indication flashes in the display.
Recording From CDs
13
EN
Recording From CDs
Fading In or Out
You can manually fade in or out to prevent tracks from
starting or ending abruptly.
Note that you cannot use this effect when you use the
DIGITAL OUT (OPTICAL) connector (for CDP-XE500).
Fading in or out at the point you want
(except for CDP-XE200) Z
FADER
1 Press EDIT/TIME FADE repeatedly before you
start playing until “ ” and “A” in the
indication appear in the display.
2 Press 0 or ) to specify the playing time.
Each time you press these buttons, the display
changes as shown below, with the playing time of
one side following each indication.
n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - - .- - N
(23.00) (27.00) (30.00) (37.00) (45.00)
When you select “HALF”
The player sets the playing time to a half of the total
playing time.
3 Press · to start playing.
At the specified time the play fades out and the
player pauses. “B” in the indication appears
in the display.
4 To record on side B, reverse the tape and press ·
or P on the player to resume playing.
Again, the play fades out at the specified time.
To cancel Time Fade
Press EDIT/TIME FADE.
You can freely specify the playing time
See “You can freely specify the tape length” on page 12 .
You can change discs during Time Fade
If the play ends before the specified fade-out time, (for
example, when you record CD-singles on a tape) change
the disc. The specified fade-out time is counted only
during playing.
You can fade in to resume playing in Step 4
After you reverse the tape, press FADER on the remote.
Note
Time Fade will be cancelled if you press 0 or ) during
the operation.
To
Start play fading in
End play fading out
Press FADER
During pause. The Q indication
flashes and play fades in.
When you want to start fading out.
The q indication flashes. The play
fades out and the player pauses.
Fading time lasts for 5 seconds. If you press FADER
during Music Scan (page 8), fading time changes to 2
seconds.
Fading out at the specified time (Time
Fade) (CDP-XE500 only)
You can have the player fade out automatically by
specifying the playing time. Once you set the Time
Fade, it works twice, that is, the play fades out at the
end of both sides of a tape.
EDIT/TIME FADE
0 / )
·
Recording From CDs
14
EN
Adjusting the Recording Level
(Peak Search)
(CDP-XE500 only)
The player locates the highest level among the tracks to
be recorded to let you adjust the recording level before
you start recording.
1 Before you start playing, press PEAK SEARCH.
“PEAK” flashes in the display and the player
repeats the portion of the highest level.
2 Adjust the recording level on the deck.
3 Press p on the player to stop Peak Search.
“PEAK” disappears from the display.
Note
The portion with the highest level may differ every time you
try the adjustment on the same disc. The difference is,
however, so slight that you won’t find any problem in
adjusting the recording level precisely.
PEAK SEARCH
p
Notes on CDs
On handling CDs
• To keep the disc clean, handle the disc by its edge. Do not
touch the surface.
• Do not stick paper or tape on the disc.
• Do not expose the disc to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in direct
sunlight as there can be considerable rise in temperature
inside the car.
• Do not use any commercially available stabilizer. If you do,
the disc and the player may be damaged.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the
disc with a cleaning cloth.
Wipe the disc from the
center out.
Additional Information
Not this way
• Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
Additional Information
15
EN
Additional Information
Troubleshooting
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
There’s no sound.
/ Check that the player is connected securely.
/ Make sure you operate the amplifier correctly.
/ Adjust the output level with LINE OUT LEVEL +/–
on the remote (CDP-XE500 and CDP-XE300 only).
The CD does not play.
/ There’s no CD inside the player (“no dISC” appears).
Insert a CD.
/ Place the CD with the label side up on the disc tray
correctly.
/ Clean the CD (see page 14).
/ Moisture has condensed inside the player. Remove
the disc and leave the player turned on for about an
hour (see page 2).
The recording level has changed (CDP-XE500 and CDP-
XE300 only).
/ The recording level changes if you adjust the output
level with LINE OUT LEVEL +/– on the remote
during recording.
The remote does not function (except for CDP-XE200).
/ Remove the obstacles in the path of the remote and
the player.
/ Point the remote at the remote sensor g on the player.
/ Replace all the batteries in the remote with new ones
if they are weak.
Specifications
Compact disc player
Laser Semiconductor laser (λ = 780 nm)
Emission duration: continuous
Laser output Max 44.6 µW*
* This output is the value measured at
a distance of 200 mm from the
objective lens surface on the Optical
Pick-up block with 7 mm aperture.
Frequency response 2 Hz to 20 kHz ± 0.5 dB
Signal-to-noise ratio More than 100 dB
Dynamic range More than 98 dB
Harmonic distortion Less than 0.0045%
Channel separation More than 95 dB
Outputs
LINE OUT
DIGITAL
OUT
(OPTICAL)
(CDP-XE500
only)
PHONES
(CDP-XE500
only)
General
Power requirements
Maximum
output
level
2 V
(at 50 kilohms)
–18 dBm
10 mW
Load
impedance
Over 10 kilohms
Wave length: 660 nm
32 ohms
Jack
type
Phono
jacks
Optical
output
connector
Stereo
phone
jack
Where purchased
Europe
Canada
Australia
Other countries
Power requirements
220 V – 230 V AC, 50/60 Hz
120 V AC, 60 Hz
240 V AC, 50 Hz
110 V – 120 V or 220 V – 240 V AC,
adjustable, 50/60 Hz
Power consumption 10 W
Dimensions (approx.) 430 × 95 × 295 mm
(w/h/d) (17 × 3 3/4 × 11 5/8 in.) incl. projecting
parts
Mass (approx.) CDP-XE500: 3.0 kg (6 lbs 10 oz)
CDP-XE300/XE200: 2.9 kg (6 lbs 7 oz)
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs) (1)
Remote commander (remote) (except for CDP-XE200) (1)
Sony SUM-3 (NS) batteries (except for CDP-XE200) (2)
Design and specifications are subject to change without notice.
Index
16
EN
Names of controls
Buttons
CHECK 11
CLEAR 11
CONTINUE 6
EDIT/TIME FADE 12
FADER 13
LINE OUT LEVEL +/– 6
MUSIC SCAN 8
§ OPEN/CLOSE 6
PEAK SEARCH 14
PLAYMODE 9
PROGRAM 9
REPEAT 8
SHUFFLE 9
TIME 7
· 6
P 6
p 6
0 / ) 8
= / + 8
>10 8
Number 8
Switch
POWER 6
Connector
DIGITAL OUT (OPTICAL) 5
Jacks
PHONES 6
LINE OUT 5
Others
Disc tray 6
Display 7
≠ AMS ± 6
g 4
Index
A, B
AMS 8
Automatic Music Sensor. See
AMS
C, D
Connecting 4
Continuous Play 6
E
Editing. See Recording
F, G
Fading 13
Time Fade 13
H, I, J, K
Half disc (HALF) 12
Handling CDs 15
Hookups 4
overview 4
L
Locating
by monitoring 8
by observing the display 8
by scanning 8
directly 8
using AMS 8
M, N, O
Music Scan 8
P, Q
Peak Search 14
Playback
Continuous Play 6
Program Play 9
Repeat Play 8
Shuffle Play 9
Program 9
changing 11
checking 11
for recording 12
Program Edit 11
R
Recording 11
a program 11
using Time Edit 12
Remaining time 7
Remote control 4
Repeating
all 8
the current track 9
S
Scanning. See Music Scan
Searching. See Locating
Shuffle Play 9
T
Time Edit 12
Time Fade 13
Total playing time 7
Troubleshooting 15
U
Unpacking 4
V, W, X, Y, Z
Voltage selector 5
2
F
AVERTISSEMENT
Pour prévenir tout risque
d’incendie ou d’électrocution,
gardez cet appareil à l’abri de
la pluie ou de l’humidité.
Pour prévenir tout risque
d’électrocution, abstenez-vous
d’ouvrir le boîtier. Confiez
l’entretien de votre lecteur
exclusivement à un personnel
qualifié.
Le composant laser de cet appareil est
capable d’émettre des radiations
dépassant la limite pour la Classe 1.
Cet appareil entre dans la catégorie des
produits LASER DE CLASSE 1.
L’ETIQUETTE INDIQUANT
L’APPARTENANCE DE CE LECTEUR
A LA CLASSE 1 est apposée à l’arrière
du boîtier.
L’étiquette de mise en garde qui suit est
apposée à l’intérieur de l’appareil.
Précautions
Sécurité
• Attention — L’utilisation
d’instruments optiques avec ce
produit augmente les risques de
blessures aux yeux.
• Si un objet ou un liquide quelconque
pénètre à l’intérieur du boîtier,
débranchez le lecteur et ne l’utilisez
plus avant de l’avoir fait contrôler par
un personnel qualifié.
Alimentation
• Avant d’utiliser le lecteur, assurez-
vous que la tension d’utilisation de
l’appareil est identique à celle de
l’alimentation secteur locale. La
tension d’utilisation est indiquée sur la
plaque signalétique fixée au dos du
lecteur.
• Le lecteur reste branché sur
l’alimentation secteur tant qu’il est
raccordé à la prise murale, même si
l’appareil a préalablement été mis hors
tension.
• Si vous prévoyez de ne pas utiliser le
lecteur pendant une période
prolongée, débranchez-le de la prise
murale. Pour déconnecter le cordon
d’alimentation, tirez sur la fiche; ne
tirez jamais sur le cordon proprement
dit.
• Le cordon d’alimentation peut
uniquement être remplacé par un
centre de service après-vente agréé.
Installation
• Installez le lecteur dans un lieu
suffisamment ventilé afin de prévenir
tout risque de surchauffe à l’intérieur
du boîtier.
• Ne pas installer le lecteur sur une
surface souple comme un tapis qui
risquerait d’obstruer les ouïes de
ventilation situées sur la base de
l’appareil.
• Ne pas installer le lecteur à proximité
de sources de chaleur ou dans un
endroit excessivement poussiéreux,
soumis à la lumière directe du soleil
ou à des vibrations ou des chocs
mécaniques importants.
Utilisation
• Si vous transportez soudainement le
lecteur d’une pièce froide dans une
pièce chaude ou si vous l’installez
dans une pièce particulièrement
humide, de la condensation peut se
former sur les lentilles montées à
l’intérieur du lecteur. Le
fonctionnement du lecteur risque d’en
être affecté. En pareil cas, retirez le
disque du plateau de lecture et laissez
le lecteur sous tension pendant
environ une heure pour permettre à
l’humidité de s’évaporer.
Réglage du volume
• N’augmentez pas le volume lorsque
vous écoutez un passage offrant un
niveau d’entrée très faible ou aucun
signal sonore. Vous risquez en effet
d’endommager les haut-parleurs lors
de la lecture d’un passage présentant
un niveau d’entrée très élevé.
Entretien
• Nettoyez le boîtier, la console et les
commandes à l’aide d’un chiffon doux
imprégné d’une solution détergente
neutre. N’utilisez pas de tampon
abrasif, de poudre à récurer ou de
solvant tel que l’alcool ou le benzène.
Si vous éprouvez la moindre
difficulté concernant votre lecteur,
n’hésitez pas à consulter votre
revendeur Sony.
A propos de ce
manuel
Les instructions fournies dans le présent
mode d’emploi concernent les modèles
CDP-XE500, CDP-XE300 et CDP-XE200.
Le CDP-XE500 est le modèle utilisé pour
les illustrations. Toute différence de
fonctionnement est clairement précisée
dans le texte, par exemple “CDP-XE500
uniquement.”
Bienvenue !
Nous vous remercions d’avoir fait
l’acquisition de ce lecteur de disques
compacts Sony. Avant de faire
fonctionner cet appareil, nous vous
recommandons de lire attentivement le
présent mode d’emploi et de le conserver
pour toute référence ultérieure.
Pour les utilisateurs au Canada
ATTENTION
POUR PREVENIR LES CHOCS
ELECTRIQUES, NE PAS UTILISER
CETTE FICHE POLARISEE AVEC
UN PROLONGATEUR, UNE PRISE
DE COURANT OU UNE AUTRE
SORTIE DE COURANT, SAUF SI
LES LAMES PEUVENT ETRE
INSEREES A FOND SANS EN
LAISSER AUCUNE PARTIE A
DECOUVERT.
Getting Started
3
F
Préparation
Déballage .........................................................................................................4
Raccordement du système............................................................................. 4
Lecture d’un disque compact.................................................................... 6
Lecture de disques compacts
Utilisation de la fenêtre d’affichage ............................................................. 7
Localisation d’une plage déterminée ou
d’un passage particulier sur une plage ....................................................... 8
Lecture de plages répétée .............................................................................. 8
Lecture dans un ordre quelconque (lecture aléatoire) .............................. 9
Création de programmes musicaux (lecture programmée) ..................... 9
Enregistrement de disques compacts
Enregistrement de votre propre programme ...........................................11
Enregistrement d’un disque compact en spécifiant la longueur
de bande disponible (montage programmé) ............................................12
Fondu enchaîné d’entrée et de sortie .........................................................13
Réglage du niveau d’enregistrement (recherche du niveau de crête) ..14
Informations complémentaires
Remarques sur les disques compacts.........................................................14
Dépannage .....................................................................................................15
Spécifications .................................................................................................15
Index
Index ...............................................................................................................16
TABLE DES MATIERES
Conventions
• Les instructions fournies dans ce
manuel portent sur les commandes du
lecteur.
Vous pouvez également utiliser les
commandes que comporte votre
télécommande si celles-ci portent le
même nom ou un nom similaire à
celles de votre lecteur de disques
compacts. Dans les instructions, les
touches de la télécommande sont
indiquées entre parenthèses.
• Les symboles suivants apparaissent
dans ce mode d’emploi:
Ce symbole indique que vous
pouvez effectuer l’opération
correspondante en vous
servant de la télécommande.
(Attention que le CDP-XE200
ne peut effectuer les tâches
précisées par ce symbole.)
Ce symbole indique un conseil
ou une astuce facilitant
l’opération envisagée.
Préparation
4
F
Déballage
Assurez-vous que les accessoires suivants vous ont été
livrés:
• Câble de connexion audio (1)
• Télécommande (sauf sur le CDP-XE200) (1)
• Piles Sony SUM-3 (NS) (sauf sur le CDP-XE200) (2)
Introduisez les piles dans la télécommande
(sauf sur le CDP-XE200)
La télécommande fournie vous permet de commander
le lecteur à distance.
Introduisez deux piles R6 (AA) en faisant correspondre
les pôles + et – des piles. Lorsque vous utilisez la
télécommande, orientez-la vers le capteur de
télécommande g du lecteur.
Raccordement du système
Vue d’ensemble
Cette section décrit le raccordement du lecteur de
disques compacts à un amplificateur. Avant de réaliser
la connexion, n’oubliez pas de mettre hors tension
chacun des appareils concernés.
Préparation
Lecteur de disques compacts
Vers le secteur
Entrée audio
(R)
Entrée audio
(L)
Vers le secteur
: Sens du signal
Amplificateur
LINE OUT
(R)
LINE OUT
(L)
Câbles de connexion requis
Cordon audio (fourni) (1)
Blanc
(L)
Rouge
(R)
Rouge
(R)
Blanc
(L)
Raccordement
Lors du raccordement d’un câble audio, assurez-vous
que le code de couleur du câble correspond à celui des
prises appropriées sur les différents appareils
raccordés: rouge (droit) sur rouge et blanc (gauche) sur
blanc. Assurez-vous de la qualité des connexions afin
de prévenir les bruits de souffle et les parasites.
Amplificateur
Préparation
Quand remplacer les piles
Dans des conditions d’utilisation normales, les piles
devraient durer environ six mois. Si la télécommande
n’agit plus sur le lecteur, remplacez simultanément les
deux piles.
Remarques
• N’abandonnez pas la télécommande à proximité d’une
source de chaleur importante ou d’un endroit humide.
• Ne laissez tomber aucun corps étranger dans le boîtier de la
télécommande en particulier lors du remplacement des
piles.
• N’exposez pas le capteur de télécommande à la lumière
directe du soleil ou d’un luminaire. Cela risque de
provoquer un dysfonctionnement.
• Si vous n’utilisez pas la télécommande pendant une
période prolongée, retirez les piles afin de prévenir tout
risque de détérioration engendrée par la corrosion ou une
fuite éventuelle des piles.
Lecteur de disques compacts
Préparation
5
F
Préparation
Vous pouvez régler le niveau de sortie sur
l’amplificateur (CDP-XE500 et CDP-XE300
uniquement)
Appuyez sur la touche LINE OUT LEVEL +/– de la
télécommande. Vous pouvez réduire le niveau de sortie
jusqu’à –20 dB.
Lorsque vous baissez le niveau de sortie, l’indication
apparaît dans la fenêtre d’affichage.
Lorsque vous mettez le lecteur hors tension, le niveau de
sortie revient automatiquement au niveau maximal.
• Si vous disposez d’un appareil numérique comme un
amplificateur, un convertisseur N/A, une platine DAT ou
MD numériques (CDP-XE500 uniquement)
Raccordez le composant via le connecteur DIGITAL OUT
(OPTICAL) à l’aide du câble optique (non fourni). Retirez le
capuchon et branchez le câble optique.
Attention que, si vous établissez ce raccordement, vous ne
pouvez pas utiliser les fonctions suivantes :
• Fondu enchaîné d’entrée ou de sortie (voir page 13)
• Fondu programmé (voir page 13)
• Réglage du niveau de sortie à l’aide des touches LINE
OUT LEVEL +/- de la télécommande (voir ci-dessus)
Réglage du sélecteur de tension (à
l’exception des modèles pour l’Europe, le
Canada et l’Australie)
Assurez-vous que la position du sélecteur de tension
monté sur le panneau arrière du lecteur correspond à la
tension d’alimentation secteur locale. Si ce n’est pas le
cas, amenez ce sélecteur dans la position voulue en
vous aidant d’un tournevis avant de brancher le cordon
d’alimentation secteur sur une prise murale.
POC-15
Câble optique (non fourni)
Appareil numérique
Remarque
Si vous effectuez le raccordement via le connecteur DIGITAL
OUT (OPTICAL), des parasites peuvent se manifester lorsque
vous activez la lecture d’un disque compact autre que
musical, comme un CD-ROM.
Lecteur de disques compacts
Branchement du cordon d’alimentation
Branchez le cordon d’alimentation sur une prise murale.
Et maintenant ?
Votre lecteur est à présent prêt à l’emploi.
Si vous n’êtes pas familiarisé au mode de lecture des disques
compacts, reportez-vous à la section “Lecture d’un disque
compact” à la page 6.
Passez ensuite aux sections suivantes pour les autres
opérations.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
Sony CDP-XE200 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Sony CDP-XE200 Owner's manual
- español: Sony CDP-XE200 El manual del propietario
