Marvel 15IM-BB-F-L Mode d'emploi

Marque: Marvel

Modèle: 15IM-BB-F-L

Catégorie: Fabricants de glaçons

Taper: Mode d'emploi

Clear Ice Machine

Machine à glacons transparente

MA15C*

ML15C*

MO15C*

MP15C*

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

CONTENTS

Figure 1

Contents:

Welcome ..............................................................................2

Warranty registration ..........................................................2

Safety information ...............................................................3

Unpacking your appliance ..................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the drain plumbing ...............................................6

Gravity drain ...................................................................6

Optional drain pump .......................................................7

Installing the water supply ...................................................8

Ice maker operation ..........................................................10

Product dimensions ..........................................................12

Using your Electronic control ............................................14

Starting your appliance ..................................................14

Turning your appliance "ON" or "OFF" ..........................15

Control lock ...................................................................15

Door ajar alarm.............................................................15

Delay start / Vacation mode .........................................15

Error codes ...................................................................16

Options menu ...............................................................16

Normal and eco mode .............................................16

Cleaning your ice machine ..............................................17

Clean reminder ............................................................17

Clean Mode ...................................................................17

Care and cleaning .............................................................19

Energy saving tips ............................................................19

Obtaining service .............................................................19

Overlay Door Panel Installation .........................................20

Troubleshooting the ice machine .......................................28

Preparing the ice machine for storage ...........................30

Drain pump removal .........................................................33

Warranty ...........................................................................35

XXXXXXXXXXXX

Warranty Registration:

We encourage all new ice machine owners to take a

moment to register their product for a more tailored

experience should you need support from us in the future.

It's recommended to send in your warranty registration card

immediately after taking delivery of your appliance.

To Register:

• Mail in your warranty registration card or register online

at marvelrefrigeration.com

• The following elds are required:

• The service number and serial number can be found on

the serial plate located on the inside of the cabinet on

the left side (See Figure 1).

• Service Number

• Serial Number

• Date of Purchase

• Dealer Name and Address

Welcome

Congratulations on your purchase of the industry's quietest

clear ice machine with the best ice clarity and purity. Your

new investment is protected by a limited warranty for the

rst year, and hermetically sealed refrigeration system parts

are covered for an additional 4 years.

Here's your guide to the operation and maintenance of your

Marvel Clear Ice Machine to ensure years of enjoyment. If

you have any questions, please contact Marvel Customer

Service or Tech Support at:

Phone: (800) 223-3900

Email:

• Customer Service: [email protected]

• Tech Support: [email protected]

MARVEL

NOTE

CAUTION

Important Safety Instructions

Warnings and safety instructions appearing in this guide are not meant to cover all possible conditions and situations that

may occur. Common sense, caution, and care must be exercised when installing, maintaining, or operating this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could

result in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

Marvel Refrigeration is committed to building a quality product in an environmentally friendly manner.

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding

internal components in place. The owners manual is

shipped inside the product in a plastic bag along with the

warranty registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance

has been thoroughly inspected and found to be in good

condition. If there is damage, the packaging will be needed

as proof of damage in transit. Afterwards please dispose of

all items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

SAFETY INFORMATION AND UNPACKING YOUR APPLIANCE

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

CAUTION

Cabinet Clearance

Ventilation is required from the bottom front of the

appliance. Keep this area open and clear of any

obstructions. Adjacent cabinets and counter top can be

installed around the appliance as long as the front grille

remains unobstructed. Overlay door models with articulated

hinges are intended for built-in applications only.

CAUTION

Outdoor Installation

Do not install in a location where the ice machine will

be exposed to direct sun exposure as this may result in

unsatisfactory performance.

CAUTION

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of

your appliance. We recommend a location where the ice

machine will be out of direct sunlight and away from heat

sources. To ensure your product performs to specications,

the recommended installation location temperature range

is from 55 to 90°F (13 to 32°C) for built in ice machines and

55 to 100°F (13 to 38°C) for freestanding ice machines.

Ice machines will not perform correctly in ambient

temperatures less than 55°F (13°C).

Front Grille

Do not obstruct the front grille. The openings within

the front grille allow air to ow through the condenser

heat exchanger. Restrictions to this air ow will result in

increased energy usage, loss of cooling capacity and low

ice production. For this reason it is important this area not

be obstructed and the grille openings kept clean. Marvel

does not recommend the use of a custom made grille as air

ow may be restricted. (See Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the

appliance should be set so the unit is rmly positioned on

the oor and level from side to side and front to back. The

overall height of your Marvel appliance may be adjusted

higher (by turning the leveling leg out) and lower (by turning

the leveling leg in). Cabinet height adjustment dimensions

are shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the

appliance forward using caution. On a level surface check

the appliance for levelness and adjust accordingly.

The front grille screws may be loosened to raise and

lower the grille to the desired height. When adjustment is

complete tighten the two front grille screws. (See Figure 5).

Rear

Leveling

Legs

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent

accidents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the

appliance to sit upright for a period of at least 24 hours

before plugging in. This will assure oil returns to the

compressor. Plugging the appliance in immediately may

cause damage to internal parts.

NOTE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING YOUR APPLIANCE

Front grille

Front grille screw

Figure 5

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any

circumstances, be installed to an un-grounded

electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must

be plugged into a mating grounding type receptacle

in accordance with the National Electrical Code and

applicable local codes and ordinances (see Figure 6). If the

circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to provide the

proper power supply. The third ground prong should not,

under any circumstances, be cut or removed.

Figure 6

Ground Fault Circuit Interrupters (GFCI) are prone to

nuisance tripping which will cause the appliance to shut

down. GFCI’s are generally not used on circuits with power

equipment that must run unattended for long periods of

time, unless required to meet local building codes and

ordinances.

Table A

Model

Minimum

Height

Maximum

Height

MA15C** 31" 32"

MO15C**

MP15CP*

⁄4" 34

⁄4"

INSTALLING THE DRAIN PLUMBING

Access

panel

Drain pipe, (not

provided)

Drain tubing, cut

to length and

install in the drain

⁄8"

(37.8 cm)

⁄16"

(17mm)

⁄4"

(3.2 cm)

⁄32"

(11.5 cm)

⁄2"

(54.6 cm)

Drain Plumbing

Your ice machine requires drain plumbing. There are 2

variations of ice machines in regards to the installation of

the drain plumbing, without a drain pump (gravity drain),

and with a drain pump.

Figure 9

Figure 8

Drain line coiled

and secured to

the back of the

unit

Uncoil the drain line, route

to an appropriate drain and

cut to the required length

Electrical Shock Hazard

Reasonable care and safe methods should be

practiced. Do NOT work with energized electrical

equipment in a wet area. Read and follow the

installation instructions listed in this manual.

WARNING

CAUTION

Failure to use an adequate drainage system, will result in

surrounding water damage and/or poor ice production.

Figure 7

CAUTION

Observe and follow all local building codes

when installing this ice machine and drain

lines.

Water

supply

inlet

Drain access in

bottom of unit

⁄32"

(10.4 cm)

Sanitary

trap

⁄4"(5.7 cm)

⁄8" (13 cm)

Gravity Drain (no drain pump):

The ice machine is shipped with the drain line installed,

coiled and secured to the back of the cabinet as shown

in Figure 7. It can be uncoiled, routed to an appropriate

drain and cut to length as required. Additionally there is the

provision of drain routing through the cut-out in the bottom

of the unit, (see the gray area in Figure 8). A drain can be

installed in this gray area with the drain line cut to a short

length and positioned into the drain as shown in Figure 9,

or if the ice machine is to be built-in, the drain tube could be

routed through a hole in the oor in this gray area to a drain

below.

The gravity drain line must be routed no higher than 6"

(15.2 cm) off the oor to assure proper drainage.

CAUTION

INSTALLING THE DRAIN PLUMBING

This drain pump is designed to be installed in Marvel ice

machines only and approved for use with water only.

CAUTION

Figure 10

Drain pump

vent tube.

Keep this

open to

assure air

ows freely

as water

enters

the pump

reservoir.

Drain line coiled and

secured to the back of the

cabinet. Uncoil, route to

an appropriate drain and

cut to length.

Optional Drain Pump.

An optional drain pump is available if you have purchased

an ice machine without one and do not have access to a

gravity drain. Installation instructions are provided with the

optional drain pump. Contact Marvel customer service at

800-223-3900 or your dealer for ordering.

Electrical Shock Hazard

Risk of electrical shock or personal injury could

occur due to moving components, if the machine

compartment access cover is removed before

unplugging the ice machine power cord.

WARNING

Reverse osmosis, (RO), water, softened water, and de-

ionized water are not recommended as they can adversely

affect the quality and quantity of the ice.

Water

Supply

Line

Clamp and

Screw

Figure 11

Back view of

ice machine

NOTE

CAUTION

INSTALLING THE WATER SUPPLY

Compression

tting

Water

supply

line

Water supply

service loop

to shut off

valve

Water valve

inlet

Water Supply

Observe and follow all local building codes when installing

this appliance.

This ice machine must be connected to a potable cold

water supply line. delivering water pressure between a

minimum of 20 psi and a maximum of 120 psi.

Use

⁄4" copper tubing for your water supply which is

available at any local hardware or plumbing supply store.

Route the

⁄4" copper tubing to suit your installation being

sure not to kink the tubing. Purchase enough copper tubing

length to allow a coil to be formed behind the unit for a

"service loop" which will allow the appliance to be pulled

out from the installation for servicing or cleaning. (See

Figure 11). Connect the copper tubing to the "top side" of a

cold water pipe to prevent the ice-maker from plugging with

sediment.

A shutoff valve is recommended on the water supply line to

ease servicing the appliance. NOTE: A SELF-PIERCING

TYPE VALVE IS NOT RECOMMENDED as they are prone

to clogging with sediment which will create pressure drop

reducing the water supply to the unit.

Connect the copper tubing water supply to the water valve

inlet with a 1/4" compression nut tting.

IMPORTANT: Secure the water supply line to the back of

the cabinet with the screw and strain relief clamp provided

in the corner of the back panel. (See Figure 11).

Make certain all connections are watertight after

installation. Form the tubing so that it will not vibrate

against the cabinet body or kink when your appliance is

moved in and out of position.

This ice machine is designed to make clear ice from the

majority of water sources on a daily basis. If your results

are unsatisfactory, your water may need to be ltered or

treated. A water specialist can recommend proper water

treatment.

CAUTION

To prevent water leaks:

• The water line tting is to be used with copper tubing

only. Do not use with plastic tubing.

• Do not use any thread sealers on this water line tting.

INSTALLING THE WATER SUPPLY

Procedure for Testing Drain System

(both gravity and drain pump models)

Drain pump models have a safety feature that will interrupt power to the unit if a high-limit condition occurs to prevent

ooding. This safety feature can be initiated by a restriction in the drain system and will continue until high-limit condition

is corrected, at which time power will be restored to the unit. Power interruption can be detected when no icons are

visible in the display area of the user interface (Figure 12). Once power is returned, a startup chime will sound followed by

a self-test, and "OFF" should be visible in the display area.

Drain pump vent

tube. Keep this

open to assure

air ows freely as

water enters the

pump reservoir.

Figure 14: Location of vent tube.

Figure 13: Example of an open drain.

Sanitary trap

hours

ICE

1 4 6 8

OFF CLEAN

DOOR

ECO

days

On/off Menu Light Delay timer Lock

Figure 12: User interface display during power interruption.

7. After checking the above requirements, repeat step 4 and verify the water drains completely without power

interruption. If problems persist call a qualied service technician and/or plumber.

Air gap

between

end of

drain line

and top of

water level

Once the drain line is plumbed, perform the following:

1. Plug the ice machine into 115v power supply.

2. Place unit in the nal installation location.

3. Turn the unit off via the user interface (display will indicate “OFF”). The drain pump will still be operational during off

mode if the unit has one.

4. Slowly pour 3-qts of water into the ice storage bin. All water should drain completely.

5. If water drains fully and without power interruption, the drain system has been successfully tested and further

installation of the ice machine can be continued.

6. If the water does not drain or a power interrupt occurs, check the following:

a. There are no kinks or restrictions in the drain line. (Note: Drain line needs to be cut to the required length and any

excess tubing should be removed to prevent possible restrictions).

b. Drain line was run according to the guidelines for maxiumum allowable rise and run as shown in the table below:

Rise Above Floor Level 8 ft. 9 ft. 10 ft.

Maxium Allowable Drain Line Length 20 ft. 15 ft. 10 ft.

c. Your drain line is plumbed into an open drain (Figure 13).

d. The vent tube on the back of the unit is open (Figure 14).

The Ice Making Process

Your ice machine is unique in how it forms ice with

fractional freezing to form a slab of ice that is clear and

has less dissolved solids than the water it is produced

from. This is accomplished by running water over the cold

evaporator plate (see Figure 15) which gradually freezes

the water to produce the ice slab. Pure water freezes rst,

leaving the dissolved solids in the residual reservoir water

to provide clear ice.

Figure 15

When the ice slab reaches the correct thickness, the ice

sheet is released and slides onto the grid cutter (see

Figure 17). Here, the ice slab is cut into squares by the grid

cutter’s heated wires (see Figure 18). The water containing

the dissolved minerals is drained after each freezing cycle.

Fresh water enters the machine for the next ice making

cycle.

Figure 17

Water distributor

Water

reservoir

Evaporator

Circulation

Pump

Reservoir

drain plug

Figure 16

Front

panel

Bin Level

Sensor

Ice

Deector

Grid Cutter

OPERATION OF THE ICE MACHINE

The bin level sensor is located in the ice bin, it senses

when the ice supply is low or full and starts or stops the ice

making process accordingly.

If the water supply is turned off to the ice machine be sure

to set the electronic control to the “OFF” position or remove

power to the unit.

New Sounds

The ice machine will make sounds that are different than

your household refrigerator. Because these sounds are

new to you they may be of a concern but are most likely

normal. The ice production process will make noises that

are not typical in a refrigeration product, ice falling onto

hard surfaces, water cascading across the evaporator, and

valves opening and closing. Following are some of the

sounds that you may hear:

A buzzing sound will be heard when the water valve

opens to ll the water reservoir.

A rattling noise which could be water owing through the

water line.

A splashing sound when water is owing over the

evaporator plate and into the water reservoir.

A "thud" when the ice slab is released from the

evaporator plate and slides onto the grid cutter.

"Clicks" when the cubes fall into the ice storage bin.

A gurgling sound which is refrigerant owing in the ice

machine.

An air noise from the condenser fan.

Ice Production

In normal mode the ice machine will produce up to 39

pounds (17.7 kg) of clear ice in a 24-hour period when

installed in a 72°F ambient with a 55°F water supply. In

"ECO" mode (see page 16) the ice machine will produce up

to 29 pounds (13.2 kg) of clear ice in the 24 hour period.

“Initial” ice production and ice accumulated in the storage

bin will vary signicantly. This is normal. During the rst

24-hours of operation the unit will produce up to 39 lbs of

ice at the above ambient and water temperature conditions,

but when starting with an empty ice storage bin, the storage

bin may only accumulate up to 18 lbs of ice. By design,

the ice storage bin is maintained at a temperature slightly

above freezing to allow the stored ice to slowly melt, to

preserve the ice quality and clarity and assure a constant

supply of fresh ice. As ice is accumulated in the bin, the ice

production rate will overcome the ice melt and the storage

bin will ll to capacity.

NOTE

OPERATION OF ICE MACHINE

The ice machine will keep producing ice until the ice

machine’s bin is full and will restart automatically when

ice needs to be replenished in the bin. The ice bin is

not refrigerated, and some melting will occur by design

to preserve the ice quality and clarity. Allow your ice

machine to run for 24-48 hours to accumulate ice in the ice

machine’s bin.

Figure 18

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MA15C*S 15" 31

⁄4" to 32

⁄4" 24" 14

⁄8" 31" to 32" 23

⁄8" 25

⁄2" 37

⁄8" 16

⁄8"

MA15C*P 15-

⁄4" 31

⁄4" to 32

⁄4" 24" 14

⁄8" 31" to 32" 22

⁄8" - 38

⁄8" 14

⁄4"

ML15C*P

MP15CPP

15" 34" to 35" 24" 14

⁄8" 33

⁄4" to 34

⁄4" 22

⁄8" - 38

⁄8" 14

⁄4"

ML15C*S

ML15C*G

15" 34" to 35" 24" 14

⁄8" 33

⁄4" to 34

⁄4" 23

⁄8" 25

⁄2" 37

⁄8" 16

⁄8"

MO15C*S 15" 34" to 35" 24" 14

⁄8" 33

⁄4" to 34

⁄4" 23

⁄8" 26

⁄8" 37

⁄8" 16

⁄8"

MP15CPS

MP15CPG

15" 34" to 35" 24" 14

⁄8" 33

⁄4" to 34

⁄4" 23

⁄8" 26

⁄8" 38

⁄8" 17

⁄2"

"A"

"B"

"C"

"D"

"E"

Figure 19

Figure 19a

Figure 20

If necessary to gain clearance inside the rough-

in opening a hole can be cut through the adjacent

cabinet and the power cord routed through this hole to

a power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord

plug. Not all recessed outlet boxes will work for this

application as they are too narrow, but a recessed

outlet box equivalent to Arlington #DVFR1W is

recommended for this application, (see Figure 20).

PRODUCT DIMENSIONS

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MA15C** 115V/60Hz/15A

100 lbs

(45.5 kg)

ML15C**

MO15C**

MP15CP*

115V/60Hz/15A

105 lbs

(47.7 kg)

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and

appliance.

"F"

"D"

"E"

"J"

"G"

Water

inlet

⁄8"

(12.4 cm)

⁄4"

(3.2 cm)

CL Gravity

drain

Figure 21

(S) solid

door shown

⁄2"

(54.6cm)

⁄16"

(17.6 cm)

"H"

USING YOUR ELECTRONIC CONTROL

Starting your clear ice machine:

Plug the ice machine into a 115 volt wall outlet,

(see page 5 for electrical information). Your

appliance is shipped from the factory in the "ICE" mode

and will begin start-up of ice production after the start-up

routine.

Upon applying power to the unit, or after a power

interruption, the Ice machine will perform a self-test,

followed by a harvest cycle to clear any in-process ice

production. This start-up routine, (“after power is applied

to the unit”), takes approximately 13 minutes to complete

before an ice production cycle starts.

If the appliance does not start, conrm the wall outlet has

power, and the control is in the "ICE" mode, (see Options

section below). Do not start the ice machine in "ECO"

mode. "ECO" mode should only be used after there is a full

bin of ice.

hours

ICE

1 4 6 8

OFF CLEAN

DOOR

ECO

days

"ON/OFF" icon : used for turning the

appliance on and off.

"MENU" icon : used to access optional

functions in the user interface.

Display icons:

ICE

hours

days

"Clock" icon : used to enter the Delay start/

vacation mode.

"LOCK" icon : used to lock out functions in

the user interface.

Display area text:

ICE

OFF

DOOR

CLEAN

ECO

Signies the appliance is on and producing

ice.

Signies the appliance is off

Signies a door ajar alarm condition.

Cleaning is recommended or the appliance

is in the clean mode.

Signies the appliance is in economical ice

production mode.

Figure 22

User interface display

On/off Menu Display area Delay timer Lock

When lit, this signies the delay start/vacation mode is

operational.

Hours or days will be lit

Hours or days timer is set for

Delay start/Vacation mode:

The control display is covered with a clear plastic protective

lm. This lm may be removed by carefully lifting at a

corner.

NOTE

Light

"LIGHT" icon: used to turn the interior light

on and off, glass door models only.

Turning your ice machine On and Off:

If your appliance is on, "ICE" will be displayed.

To turn the appliance off, push and hold the "ON/

OFF" icon for 3-seconds. The display will show

"OFF" .

The drain pump (if equipped) and the interior light

will still be functioning during the OFF mode. To

turn the appliance back on, press and hold the "ON/OFF"

icon for 3-seconds, the display will show "ICE".

ICE

OFF

USING YOUR ELECTRONIC CONTROL

Control Lock:

The user interface can be locked to avoid

unintentional changes from things like cleaning. To

lock the appliance, push and hold the "LOCK" icon

for 5-seconds. The "LOCK" icon will ash 3 times, then

change to steady back-lit. To unlock the user interface,

press and hold the "LOCK" icon for 5-seconds, and the

back-light will turn off.

NOTE

The "LOCK" icon is the only active key in this mode. If other

icons are pressed while in the lock mode the "LOCK" icon

will ash 3 times, and an audible tone will sound, to remind

the user the appliance is in the lock mode.

When turned off, the ice machine will complete its

current ice production cycle then shut off.

Door ajar alarm:

If the door is open, or not closed properly for 5

minutes the "DOOR" indicator will illuminate and

ash and an audible tone will sound. The audible

alarm can be muted by pressing the "Lock" keypad.

This alarm condition can be reset by closing the

door or momentarily pressing the "ON/OFF" icon,

(i.e.-if you are cleaning the storage compartment, etc.). The

alarm will recur in 5 minutes if the alarm condition persists.

DOOR

Turning the ice machine "OFF" will only terminate the

ice production, it does not remove power from the

appliance. Always unplug the power cord from the

wall outlet before servicing the unit.

WARNING

Delay start/Vacation mode:

Your ice machine is equipped with a delay start function.

This feature can be used to temporarily shut the appliance

off for 1, 4, 6, or 8 hours or days. Upon completion of the

selected delay period, the appliance will resume operation.

This is ideal for temporarily stopping ice machine noises or

to save water and electricity if you are away from home but

want fresh ice upon your return.

To enter the delay start mode, press the "CLOCK"

icon while the appliance is in "ICE" mode. This will

delay the next harvest by the time displayed. Each

additional press of the "CLOCK" icon will add time,

from 1, 4, 6, or 8 hours, to 1, 4, 6, or 8 days. The next

press after 8 days will leave delay set

mode. After the desired time has been

selected, press the "ON/OFF" icon for 2 seconds

to accept, your unit will shut off and a clock icon

and your selected time will be displayed. When the

selected time has elapsed, normal ice production will

resume.

To cancel the delayed start, press

and hold the "ON/OFF" icon until the

appliance enters OFF, then press and

hold the "ON/OFF" icon again until the

appliance enters "ICE" mode.

1 4 6 8

hours

days

ICE

OFF

Error Codes

Error Displayed Code Error Description Action to Take

Bin Sensor error

"OFF" will ash continuously in 1

second intervals in the display. No

audible alarm will sound.

Failed temperature sensor. Machine operation will

immediately enter an OFF state.

Call service to have the

temperature sensor replaced.

System Sensor error

"ICE" will ash continuously in

the display. No audible alarm will

sound.

Failed condenser temperature sensor. Machine operation

will continue but ice production cycle will not adapt to

varying ambient conditions, so ice quality may vary.

Call service to have the

temperature sensor replaced.

Communication error

Continual ashing of all indicators

on the display.

Loss of communication between the main board and the

user interface.

Call service to have a

diagnostic check.

Error codes:

The ice machine is monitored continuously. Any OPEN or

SHORTED circuit condition with a temperature sensor or

miscommunications between the control and user interface

will initiate an ERROR CODE as listed below:

ICE

Options menu:

Normal and ECO mode:

Your ice machine comes with an optional "ECO" mode.

This new feature allows you to tailor ice production to a

conservative rate, saving approximately 25% energy and

30% water from routine operation. While in this mode

ice production will slow and the appliance will use less

water and electricity. "ECO" mode should only

be initiated after there is a full bin of ice. To enter

"ECO" mode do the following:

• Press the "MENU" icon twice and the green

"ECO" will ash.

• Press and hold the "ON/OFF" icon until the

green "ECO" stops ashing and remains

illuminated.

• To return to the standard operating rate press the

"MENU" icon twice, the ECO will turn off and

the "ICE" will be ashing. Press and hold the

"ON/OFF" icon until the "ICE" stops ashing

and remains illuminated.

ECO

USING YOUR ELECTRONIC CONTROL

Changing the Tri-Color lighting: (MP15CP

Models Only)

Figure 23

The light switch for changing

the light color is located in the toe

grille. Move the switch (see Figure

23a) to the left or right to change

the color of the light between blue,

white, or amber.

Figure 23a

Three position

slide light switch

CLEANING YOUR ICE MACHINE

CAUTION

Forcing ice through the grid cutter will break the grid cutter

wires.

CAUTION

Remove all ice

from the evaporator

plate and grid cutter

area that is not

embedded in wires

Figure 24

Figure 25

Clean mode:

To ensure maximum performance and ice quality, it is

recommended to clean your ice machine once every six

months. This simple cleaning routine will also ensure water

and energy use continues at optimum efciency.

Clean reminder:

A "CLEAN" reminder will occur every 6 months

to remind you that it may be time to clean your

appliance. Over time mineral build up on the cold

evaporator plate can occur which can adversely

affect the quality of your ice. This build-up is

dependent on your water source and usage. Normal

ice production will continue while the "CLEAN" reminder

is displayed. You may clear the "CLEAN" reminder at any

time by momentarily pressing the "ON/OFF" icon. When

reset, the "CLEAN" reminder will reset and not occur for

another 6 months. If you choose to clean the appliance at

this time, see the options menu section below.

CLEAN

NOTE

Homes with poor water quality or high clear ice usage

might require more frequent cleaning.

To clean your ice machine you will need to purchase a

"nickel safe" ice maker cleaner. Cleaner can be obtained by

contacting Marvel customer service at 800-223-3900

or email [email protected].

Use only Marvel-approved ice machine cleaner and follow

all label warnings and directions. Incorrect chemical

usage, and any damage that may result, is not covered by

warranty.

Available to order

Clear Ice Machine Cleaner, 4-oz. bottle Part # S41013789

NOTE

For reference see our "Care and Cleaning video" at the

website: www.marvelrefrigeration.com.

Once you have your cleaner:

Turn the ice machine off by pressing and holding

the "ON/OFF" icon for 3 seconds. "OFF" will be

displayed on the control.

Remove all ice from the ice bin (see Figure 27).

Drain the water from the water reservoir by removing the

black plug from the bottom of the fresh water reservoir (see

Figure 28). After the water is drained, replace the plug in

the bottom of the reservoir.

Allow all of the ice to fall from the evaporator plate

and remove any ice from the grid cutter. If there is ice

embedded in the grid cutter wires, wait for it to melt and

fall out. Do not try to remove ice that is embedded in

the grid cutter wires as that may break the wires. (See

Figures 24 and 25).

OFF

CLEANING YOUR ICE MACHINE

Figure 27

Figure 26

Remove all of

the ice from

the ice bin

Figure 28

Remove the

black reservoir

drain plug from

the bottom of

the reservoir.

Figure 29

Turn the ice machine back on by pressing and

holding the "ON/OFF" icon for 3 seconds. The

display will indicate "ICE" mode. Press and hold

the "MENU" icon until a ashing "CLEAN"

is displayed. Press the "ON/OFF" icon until

"CLEAN" stops ashing. Your ice machine will

now enter the clean cycle.

The clean and rinse cycle will take about 49

minutes.

After the clean cycle is complete the ice machine

will return to the "OFF" position.

After the cleaning cycle is completed, verify that all build-up

has been removed. If not repeat the clean cycle procedure.

ICE

CLEAN

OFF

Refer to your cleaning solution instructions to determine

the proper amount of cleaning solution to add based on

2 quarts (1.9 liters) of water. Lift fascia door up to access

evaporator plate. (See Figure 29). Pour the cleaning

solution slowly on the evaporator plate so it ows down into

the fresh water reservoir. (See Figure 30).

Figure 28b

Splash shield

brackets

Replace the splash shield if removed.

Pour cleaning solution slowly

onto the front edge of evaporator

plate behind the grid cutter.

Figure 30

Evaporator

plate

Grid cutter

Splash shield

Lift fascia door up to

access evaporator plate

CARE AND CLEANING AND ENERGY SAVING TIPS

OBTAINING SERVICE

Front Grille

Be sure that nothing obstructs the required air ow openings

in front of the cabinet. At least once or twice a year, brush or

vacuum lint and dirt from the front grille area (see page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Cleaning

Routine cleaning of the stainless steel surfaces will serve

to greatly extend the life of your product by removing

contaminants. This is especially important in coastal areas

which can expose the stainless to sever contaminants such

as halide salts (sodium chloride).

It is strongly recommended to periodically inspect and

thoroughly clean crevices, weld points, under gaskets,

rivets, bolt heads, and any locations where small amounts

of liquid could collect, become stagnant, and concentrate

contaminants. Additionally, any mounting hardware that is

showing signs of corrosion should be replaced.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner,

undiluted detergent or chlorine based cleaners.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or

mopping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as

possible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

CAUTION

Energy Saving Tips

The following suggestions will minimize the

cost of operating your ice machine appliance.

1. Do not install your appliance next to a hot appliance,

(stove, dishwasher, etc.). heating air duct, or other heat

sources.

2. Install product out of direct sunlight.

3. Assure the front grille vents at front of the ice machine

beneath the door are not obstructed and kept clean to

allow ventilation for the refrigeration system to expel

heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. Minimize door openings and duration of door openings.

6. Set the control to the “off” position if accessing the

interior to spot clean or remove large quantities of ice

requires the door to be open for an extended period of

time.

7. Use ECO mode if maximum ice production quantities

are not required.

8. Use the delay start function if the ice machine will not

be used for long periods of time.

If Service is Required:

• If the product is within the rst year warranty period

please contact your dealer or call Marvel Customer

Service at 800.223.3900 for directions on how to obtain

warranty coverage in your area.

• If the product is outside the rst year warranty

period, Marvel Customer Service can provide

recommendations of service centers in your area. A

listing of authorized service centers is also available

at www.marvelrefrigeration.com under the service and

support section.

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "C" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service Number

Date Warranty Card Sent (Must be

within 10 days of purchase).

Table C

CAUTION

WARNING

Use extreme caution with the articulated hinges. The

hinge is self closing and many pinch points exist prior

to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

WARNING

The articulated hinges have many pinch points.

Carefully close / collapse the hinges as soon as the

door is removed from the cabinet.

OVERLAY DOOR PANEL INSTALLATION - ML15C & MP15C MODELS

If you purchased an overlay panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

⁄8" (15

mm) and

⁄4" (18 mm) are accommodated.

It is important to use the factory provided grille that came

with the product to assure proper air ow is maintained

through the condenser. The use of a custom grille is not

recommended and will void the warranty.

WARNING

Overlay panel models are designed for use with built-

in installations only. Use in freestanding installations

could result in personal injury.

Step 1: Removing the Door

With a phillips screwdriver remove the screw and "P" clamp

from the bottom of the door near the hinge. See Figure 31b.

Disconnect the door wire harness by pressing and holding

down the locking tab on the wire connector and pulling the

connector apart. See Figure 32.

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges

can be slipped off of the screws when sliding the door to

the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

⁄2 inch and

remove the hinges and door from the unit.

Optional: After the cleaning cycle has been completed ,

you may wash the interior with a mild detergent / dish soap

or a solution of two tablespoons of baking soda and one

quart of water. Rinse with clean water.

Replace the grid cutter cover.

After cleaning it is recommended you discard the ice

produced after 3 hours of ice production.

If you cancel clean mode after adding ice maker

cleaner, you must re-start cleaning and allow clean

cycle to complete to remove the cleaning solution

before resuming ice production.

WARNING

Do not use bleach based cleaners or any abrasive cleaning

products. Chlorine based cleaners will attack the stainless

steel, making it susceptible to corrosion.

Canceling clean mode:

To exit clean mode press and hold the "ON/OFF" icon

until "OFF" is displayed. Wait 3 minutes for clean mode to

complete it's cancel routine before turning unit back on by

pressing and holding the "ON/OFF" icon. If you turn the

unit back on before the 3 minutes has elapsed, the display

will show "CLEAN" and the unit will shut itself off upon

completion of the 3 minute clean cancel routine.

ICE

Your ice machine is now ready to

restart. Press and hold the "ON/

OFF" icon for 3 seconds until "ICE is

displayed.

La page charge ...

Marvel 15IM-BB-F-L Mode d'emploi

Marque: Marvel

Modèle: 15IM-BB-F-L

Catégorie: Fabricants de glaçons

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel 15IM-BB-F-L Operating instructions

Marvel 15IM-BB-F-L Mode d'emploi

Marvel 15IM-BB-F-L Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents