Samsung DTG36P875NS Guide d'installation

Installation Manual

Gas Cooktop

DTG30P875N*

DTG36P875N*

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 1 2020-05-27 �� 11:00:26

2 English

WARNING: If the information in this manual is not followed

exactly, a re or explosion may result causing property damage,

personal injury or death.

• DO NOT store or use gasoline or other ammable vapors and

liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch.

- DO NOT use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the re

department.

• Installation and service must be performed by a qualied

installer, service agency, or the gas supplier.

Contents

Before you begin 3

Important safety information 3

Gas cooktop components 8

What’s in the box 8

Installation requirements 10

Pre-installation checklist 10

Location requirements 10

Gas supply requirements 12

Special gas requirements (gas models sold in Massachusetts) 13

Electrical requirements 13

Installation instructions 14

Installing your gas cooktop 14

Step 1. Unpack the cooktop 14

Step 2. Installing the cooktop. 14

Step 3. Connect the cooktop to gas supply 16

Step 4. Check for gas leaks. 17

Step 5. Electrical connections. 18

Step 6. Assemble the cooktop burners. 18

Step 7. Check the ignition of cooktop burners 20

Step 8. Checking the ame quality. 20

Step 9. Install the grates. 21

Step 10. Final installation checklist 22

LP (Propane) conversion instruction 22

Supplied parts 23

Converting the pressure regulator 24

Converting the cooktop burners 25

Adjusting low ame setting on cooktop burners 26

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 2 2020-05-27 �� 11:00:26

English 3

Before you begin

About this manual

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.

Important note to the installer

• Read all instructions contained in these installation instructions before installing

the cooktop.

• Remove all packing materials from the cooktop compartments before connecting

the electric and gas supply to the cooktop.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the consumer.

• Installation of this appliance requires basic mechanical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

Important note to the consumer

Keep these instructions with your user manual for future reference.

• As when using any appliance generating heat, there are certain safety

precautions you should follow.

• Be sure your cooktop is installed and grounded properly by a qualied installer

or service technician.

• Make sure the wall coverings around the cooktop can withstand the heat

generated by the cooktop.

• Cabinet storage space above the cooktop burners should be a minimum of 30 in

(76.2 cm).

Important note to the servicer

The electrical diagram is attached inside the burner box.

Important safety information

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

• All electrical and gas equipment with moving parts can be dangerous. Please

read the important safety instructions for this appliance in this manual. The

instructions must be followed to minimize the risk of injury, death, or property

damage.

• Save this manual. Please Do Not Discard.

Symbols used in this manual

WARNING

Hazards or unsafe practices that may result in severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in electric shock, personal injury, or

property damage.

NOTE

Useful tips and instructions.

These warning icons and symbols are here to prevent injury to you and others.

Please follow them explicitly. After reading this section, keep it in a safe place for

future reference.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 3 2020-05-27 �� 11:00:27

4 English

Important safety information

California Proposition 65 Warning

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Commonwealth of Massachusetts

• This product must be installed by a licensed plumber or gas tter qualied or

licensed by the State of Massachusetts. When using ball-type gas shut-off valves,

you must use the T-handle type. Multiple exible gas lines must not be connected

in series.

General safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Do not touch any part of the cooktop, including

but not limited to, cooktop burners, during or

immediately after cooking.

• Know the location of the gas shut-off valve and

how to shut it off.

• Make sure the hold down brackets are properly installed on the cooktop. See the

installation instructions for more information.

• Do not let children near, in, or on the cooktop. Do not let children play with the

cooktop or any part(s) of the cooktop. Do not leave children unattended in an

area where the cooktop is in use.

• Remove all packaging materials from the cooktop before operating to prevent

ignition of these materials. Keep all packaging materials out of children’s reach.

Properly dispose the packaging materials after the cooktop is unpacked.

• Do not store any object of interest to children on the cooktop or backguard of

the cooktop. Children climbing on the cooktop to reach items could be killed or

seriously injured.

• Do not operate the cooktop if the cooktop or any part of the cooktop is damaged,

malfunctioning, or missing parts.

• Do not use the cooktop as a space heater. This cooktop is to be used for cooking

purposes only.

• Use only dry pot holders.

• Do not use the cooktop to heat unopened food containers.

• Unplug or disconnect power before servicing.

Fire safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Do not store, place, or use ammable or

combustible materials such as paper, plastic,

pot holders, linens, curtains, gasoline or other

ammable vapors or liquids near the cooktop.

• Do not wear loose tting or hanging garments

while using the cooktop.

• To avoid grease buildup, regularly clean the vents.

• Do not let pot holders or other ammable materials touch a heating element. Do

not use a towel or other bulky cloths in place of a pot holder.

• Do not use water on a grease re. To put out a grease re, turn off the heat

source and smother the re with a tight-tting lid or use a multipurpose dry

chemical or foam-type re extinguisher.

• Do not heat unopened food containers - buildup of pressure may cause container

to burst and result in injury.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 4 2020-05-27 �� 11:00:27

English 5

Important safety information

Gas safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

If you smell gas:

• Close the valve and do not use the cooktop.

• Do not light a match, candle, or cigarette.

• Do not turn on any gas or electric appliances.

• Do not touch any electrical switches or plug a

power cord into an outlet.

• Do not use any phone in your building.

• Evacuate the room, building, or area of all

occupants.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

re department.

Checking for gas leaks

• Leak testing of the appliance shall be conducted according to the manufacturer’s

instructions. Do not use a ame to check for gas leaks. Use a brush to spread a

soapy water mixture around the area you are checking. If there is a gas leak, you

will see small bubbles in the soapy water mixture at the leak point.

Electrical and grounding safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Plug into a grounded 3-prong outlet.

• Do not remove the ground prong.

• Do not use an adapter or an extension cord.

• Do not use a damaged power plug, power cord,

or loose power outlet.

• Do not modify the power plug, power cord, or

power outlet in any way.

• Do not put a fuse in a neutral or ground circuit.

• Use a dedicated 120-volt, 60-Hz, 20-amp, AC, fused electrical circuit for this

cooktop. A time-delay fuse or circuit breaker is recommended. Do not plug more

than one appliance into this circuit.

• Do not connect the ground wire to plastic plumbing lines, gas lines, or hot water

pipes.

• This cooktop must be Earth grounded. In the event of a malfunction or

breakdown, grounding will reduce the risk of electrical shock by providing a path

for the electric current. This cooktop is equipped with a cord having a grounding

plug. The plug must be rmly plugged into an outlet that is properly installed

and grounded in accordance with the local codes and ordinances. If you are

unsure whether your electrical outlet is properly grounded, have it checked by a

licensed electrician.

• The cooktop is supplied with a 3-pronged grounded plug. This cord must be

plugged into a mating, grounded 3-prong outlet that meets all local codes and

ordinances. If codes permit the use of a separate ground wire, we recommend

that a qualied electrician determine the proper path for this ground wire.

• Electrical service to the cooktop must conform to local codes. Barring local codes,

it should meet the latest ANSI/NFPA No. 70 – Latest Revision (for the U.S.) or the

Canadian Electrical Code CSA C22.1 – Latest Revisions.

• It is the personal responsibility of the cooktop owner to provide the correct

electrical service for this cooktop.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 5 2020-05-27 �� 11:00:28

6 English

Important safety information

• Make sure your cooktop is correctly installed and adjusted by a qualied

service technician or installer for the type of gas (natural or LP) you will use. For

your cooktop to utilize LP gas, the installer must replace the 5 cooktop burner

orices with the provided LP orice set, and reverse the GPR adapter. These

adjustments must be made by a qualied service technician in accordance with

the manufacturer’s instructions and all codes and requirements of the authority

having jurisdiction. The qualied agency performing this work assumes the gas

conversion responsibility.

• Installation of this cooktop must conform with local codes or, in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest

edition. In Canada, installation must conform with the current Natural Gas

Installation Code, CAN/CGA-B149.1, or the current Propane Installation Code,

CAN/CGA-B149.2, and with local codes where applicable. This cooktop has been

design-certied by ETL according to ANSI Z21.1, latest edition, and Canadian Gas

Association according to CAN/CGA-1.1, latest edition.

Installation safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Have your cooktop installed and properly grounded by a qualied installer, in

accordance with the installation instructions. Any adjustment and service should

be performed only by qualied gas cooktop installers or service technicians.

• Do not attempt to service, modify, or replace your cooktop or any part of your

cooktop unless it is specically recommended in this manual. All other service

should be referred to a qualied technician.

• Always use new exible connectors when installing a gas appliance. Do not use

old exible connectors.

• Make sure the hold down brackets are properly installed on the cooktop. See the

installation instructions for more information.

• Remove all tape and packaging materials.

• Remove all accessories from the cooktop. Grates and griddles are heavy. Use

caution when handling them.

• Make sure no parts came loose during shipping.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 6 2020-05-27 �� 11:00:28

English 7

Important safety information

Location safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• This cooktop is for indoor, household use only.

Do not install the cooktop in areas exposed to

the weather and/or water.

• Do not install the cooktop in a place which is

exposed to a strong draft.

• Select a location where a grounded, 3- prong outlet is easily accessible.

• If the cooktop is located near a window, do not hang long curtains or paper

blinds on that window.

• For the cooktop to ventilate properly, there is enough clearance at the top, back,

sides, and underneath the cooktop. The vents allow the necessary exhaust for the

cooktop to operate properly with correct combustion.

• Make sure the wall coverings around the cooktop can withstand heat up to 194

°F (90 °C) generated by the cooktop.

• Cabinet storage above the surface of the cooktop should be avoided. If cabinet

storage above the cooktop is necessary: allow a minimum clearance of 30 inches

(76.2 cm) between the cooking surface and the bottom of cabinets.

Cooktop safety

WARNING

To reduce the risk of re, electric shock, personal injuries, and/or death, obey the

following precautions.

• Make sure all burners are off when not in use.

• Do not use aluminium foil to line the grates or

any part of the cooktop.

• Do not leave burners unattended on medium or

high heat settings.

• Before igniting, make sure all burner caps are

properly in place and all burners are level.

• Always use the LITE position when igniting the burners and make sure the

burners have ignited. If ignition fails, turn the knob to OFF and wait until the gas

has dissipated.

• When you set a burner to simmer, do not turn the knob quickly. Make sure the

ame stays on.

• Do not place any objects other than cookware on the cooktop.

• This cooktop is designed to cook with a wok or wok ring attachment. If foods are

amed, they should only be amed under a ventilation hood that is on.

• Before removing or changing cookware, turn off the burners.

• Remove food and cookware immediately after cooking.

• Before removing any parts of the burner for cleaning, make sure the cooktop is

off and completely cool.

• After cleaning the burner spreader, make sure it is completely dry before re-

assembling.

• To avoid carbon monoxide poisoning, do not pour water into the cooktop well

while cleaning.

• Select cookware that is designed for top-cooktop cooking. Use cookware that is

large enough to cover the burner grates. Adjust the burner ames so that the

ames do not extend beyond the bottom of the cookware.

• To avoid cookware discoloration, deformity, and/or carbon monoxide poisoning,

do not use cookware that is exceedingly larger than the grate.

• Make sure cookware handles are turned to the side or rear of the cooktop, but

not over other cooktop burners.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 7 2020-05-27 �� 11:00:28

8 English

Gas cooktop components

Important safety information

• Stand away from the cooktop while frying.

• Always heat frying oils slowly, and watch as they heat. If you are frying foods at

high heat, carefully watch during the cooking process. If a combination of fats or

oils is to be used during frying, mix them together before heating.

• Use a deep-fryer thermometer whenever possible. This prevents overheating the

fryer beyond the smoking point.

• Use a minimum amount of oil when shallow pan-frying or deep-frying. Avoid

cooking unthawed food or food with excessive amounts of ice.

• Before moving cookware full of fats or oils, make sure it has completely cooled.

• To prevent delayed eruptive boiling, always allow heated liquids to stand at least

20 seconds after you have turned off the burner so that the temperature in the

liquid can stabilize. In the event of scalding, follow these rst aid instructions:

1. Immerse the scaled area in cool or lukewarm water for at least 10

minutes.

2. Do not apply any creams, oils, or lotions.

3. Cover with a clean, dry cloth.

Gas cooktop components

What’s in the box

Parts supplied

Cooktop burner grates (3) * Cooktop burners and

caps (5) *

Cast-iron griddle (1) *

Wok ring (1) * Template Screw (6)

(M4L10 2 ea, M4 L16 2 ea,

W

3

/16 L75 2 ea)

Regulator (1) * Hold down brackets (2) * Cover (1)

Foam tape

• Make sure you have received all of the supplied parts shown above.

• If your cooktop was damaged during shipping or you do not have all of the

supplied parts, contact your local retailer.

NOTE

If you need an accessory marked with *(asterisk), contact the DACOR Call Center

using the phone number on the last page of this manual, or visit our online parts

website: www.dacor.com

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 8 2020-05-27 �� 11:00:30

English 9

Gas cooktop components

Parts needed

Gas line shut-off

valve

Flexible metal

appliance connector

½ in (ID) x 5 ft

Flare union adapter

¾ in or ½ in (NPT) x

½ in (ID)

Flare union adapter

½ in (NPT) x ½ in

(ID)

135-degree elbow

(optional)

90-degree elbow

(optional)

Tools needed

Flat-blade

screwdriver

Phillips screwdriver Open-end or

adjustable wrench

Pipe wrench (2)

¼" Nut driver Pencil and ruler Level

Pipe joint compound

Utility knife Soapy water

solution

Pliers Saber saw

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 9 2020-05-27 �� 11:00:32

10 English

Installation requirements

Pre-installation checklist

1. When preparing cooktop opening, make sure the inside of the cabinet, and the

cooktop do not interfere with each other.

2. Remove packing materials, grate boxes, regulator with literature, and literature

package from the cooktop before beginning installation.

Location requirements

BEFORE YOU BEGIN to install this appliance, refer to the following information,

dimensions, and clearances. These dimensions must be met for safe use of the

cooktop. The location of the electrical outlet and gas piping may be adjusted to

meet the following dimensions and clearances.

CAUTION

This cooktop has been designed to comply with the maximum allowable wood

cabinet temperature of 194 °F (90 °C). Make sure the wall covering, countertops,

and cabinets around the cooktop can withstand the heat (up to 194 °F [90 °C])

generated by the cooktop. If not, discoloration, delamination, or melting may occur.

Maintain the following minimum clearance dimensions

13” MAX.

(330 mm)

13” MAX.

(330 mm)

30” MIN

(762 mm)

30” MIN

(762 mm)

12” MIN

(304.8 mm)

30” - DTG30P875N* 36” - DTG36P875N*

12” MIN

(304.8 mm)

18” MIN

(457 mm)

18” MIN

(457 mm)

2

7

/8” MIN

(73.0 mm)

12”

(304.8 mm)

3

/8” Min

(85.7 mm)

12”

(304.8 mm)

NOTE

All horizontal clearances must be maintained for a minimum of 18” (457 mm)

above the cooking surface.

Electrical outlet 12”

(30.5 cm) minimum

below countertop

3

9

/

16

”

(90.5 mm)

7

/16”

(11.1 mm)

DRAWER

NOTE

Allow

7

/16” minimum vertical clearance

from the cooktop bottom (or 3

9

/16”)

minimum depth from the countertop) to

any combustible surfaces, including the

upper edge or a drawer installed below the

cooktop.

Installation over built-in oven

90° Elbow

5” To Center of 2” Dia.

Hole From Countertop

2” Dia. Hole

(20

7

/8” from front

of countertop to

hole Center

View from Front of Cooktop

Cabinet Sides

See built-in oven installation for complete

installation instructions.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 10 2020-05-27 �� 11:00:32

English 11

Installation requirements

Overall cooktop dimensions

2

7

/16” (62 mm)

countertop to

grate surface

3

1

/8” (79.3 mm)

chassis eight

21” (533 mm)

22

3

/8” (568 mm)

A

B

C

Model A B C

DTG30P875N*

30”

(762 mm)

28

1

/8”

(715 mm)

19

3

/8”

(492.1 mm)

DTG36P875N*

36”

(914.4 mm)

33

11

/16”

(855 mm)

18

7

/8”

(479 mm)

Cutout dimensions of countertop

Vertical

combustible

surface

D

E

G

F

Rear wall

Minimum distance to combustible side

wall above countertop (both sides)

Model (D) Min. (E) Min. (F) Min. (G) Min.

DTG30P875N*

2

7

/8”

(73 mm)

19

5

/8”

(498.5 mm)

28

1

/2”

(723.9 mm)

12”

(304.8 mm)

DTG36P875N*

3

/8”

(85.7 mm)

19

1

/8”

(485.8 mm)

33

7

/8”

(860.4 mm)

12”

(304.8 mm)

Installation dimensions with downdraft hood

NOTE

• Make sure the clearance dimensions when you install the cooktop with

downdraft hood.

• The cooktop can be installed after detaching iQ Connect module.

Please refer to the instruction how to detach iQ Connect module on page 15.

iQ Connect

Module

1

4

/7” (40 mm) Min.

Cooktop

(H) Cutout to downdraft hood

iQ Connect Module

1

9

/16” (40 mm) Min.

Cooktop frame to downdraft hood

Downdraft Hood

Model (H) Min.

DTG30P875N* 2

7

/16” (62 mm)

DTG36P875N* 3” (76 mm)

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 11 2020-05-27 �� 11:00:33

12 English

Installation requirements

Single Oven Under counter

D

A

F

E

B

G

C

H

01

02

01 This cooktop can be installed above any

single built-in oven. Refer to installation

manual of oven.

02 Gas and Electrical Connections for Gas

Cooktop Must be Located in an Adjacent

Accessible Location to the Right.

Size

A

Min. 3

3

/4” (9.5 cm)

B 4” (10.1 cm)

C Min. 28

1

/2”/ Max. 28

5

/8” (Min. 72.4 cm / Max. 72.7 cm)

D Min. 1”/ Max. 1

1

/4” (Min. 2.5 cm / Max. 3.2 cm)

E Min. 27

1

/4”/ Max. 27

3

/8” (Min. 69.2 cm / Max. 69.5 cm)

F 24” (61 cm)

G Min. 22” (Min 55.9 cm)

H Max. 9

1

/2” (Max. 24.1 cm) – Junction Box

Utility locations and dimensions

Front of unit

Power cord 39

3

/8”

(100.0 cm) long

3

/8”-18 NPT male

gas inlet

* Gas inlet protrudes 1

9

/16” (4.0 cm)

from bottom.

Front of cooktop

Chassis

1

/4”

(3.2 cm)

1

15

/16”

(5.0 cm)

Gas supply requirements

Provide adequate gas supply

This cooktop is designed to operate at a pressure of 5 in (13 cm) of water column

on natural gas or 10 in (25 cm) of water column on LP gas (propane or butane).

Make sure you are supplying your cooktop with the type of gas for which it is

designed. Do not attempt to convert the appliance from the gas specied in this

manual to a different gas without consulting the gas supplier.

This cooktop is convertible for use on natural or propane gas. If you decide to use

this cooktop on LP gas, conversion must be made by a qualied LP installer before

attempting to operate the cooktop.

For proper operation, the pressure of natural gas supplied to the regulator must be

between 5 in and 13 in (13 cm and 33 cm) of water column.

For LP gas, the pressure supplied must be between 10 in and 13 in (25 cm and

33 cm) of water column.

When checking for proper operation of the regulator, the inlet pressure must be at

least 1 in (2.5 cm) greater than the operating (manifold) pressure as given.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 12 2020-05-27 �� 11:00:33

English 13

Installation requirements

The pressure regulator located at the inlet of the cooktop manifold must remain in

the supply line regardless of whether natural or LP gas is being used.

NOTE

• The cooktop comes from the factory with a regulator in the shipping carton. Use

only the regulator provided. The regulator must be installed in the gas line that

runs from the cooktop gas inlet to the gas shut off valve.

• An external manual shut-off valve must be installed between the gas inlet and

the cooktop for the purpose of turning on or shutting off gas to the appliance.

• Be sure the connectors are installed when you need coupling by a qualied

installer.

• Never reuse old connectors when installing the cooktop. The use of old

connectors can cause gas leaks and personal injury. Always use new exible

connectors when installing a gas appliance.

Special gas requirements (gas models sold in Massachusetts)

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS:

WARNING

Gas leaks may occur in your system, creating a dangerous situation.

– Gas leaks may not be detected by smell alone.

– Gas suppliers recommend you purchase and install a UL-approved gas detector.

Gas detector should be installed in accordance with the manufacturers

instructions.

• Cooktop must be installed by a qualied plumber or gas tter by the State of

Massachusetts.

• A T-handle manual gas valve MUST be installed in the gas supply line to your

cooktop.

• If a exible gas connector is used to install your cooktop, multiple exible gas

lines must not be connected in series.

Electrical requirements

WARNING

• It is the owner’s responsibility to make sure that the electrical service meets

electrical requirements and that he electrical outlet has been properly installed

by a licensed electrician.

• To reduce the risk of re, electric shock, or personal injury:

All cooktops

• Do not use an extension cord or adapter plug with this cooktop.

• This cooktop must be properly grounded.

• Check with a qualied electrician if you are in doubt as to whether your cooktop

is properly grounded.

• Do not modify the plug provided with your cooktop — if it doesn’t t the outlet,

have a proper outlet installed by a qualied electrician.

• All wiring and grounding must be done in accordance with local codes or, in the

absence of local codes, with the National Electrical Code, ANSI/NFPA No. 70 –

Latest Revision (for the U.S.) or the Canadian Electrical Code CSA C22.1 – Latest

Revisions and local codes and ordinances.

• Wiring diagram is located on the inside of the burner box.

• This cooktop is equipped with an electronic ignition system that will not operate

if plugged into an outlet that is not properly polarized.

Gas cooktops

• All gas models are equipped with a power cord with an equipment-grounding

conductor and a grounding plug.

• A 120-Volt, 60-Hz, AC, approved electrical service with 20-amp circuit breaker or

time-delay fuse is required for all U.S. and Canadian models.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 13 2020-05-27 �� 11:00:33

14 English

Installation instructions

Grounding

• All cooktops must be grounded for personal safety.

• The plug must be rmly plugged into a three-prong outlet that is properly

installed and grounded in accordance with all local codes and ordinances. In

the event of a malfunction or breakdown, grounding will decrease the risk of

electrical shock by providing a path for the electric current.

• Do not use a damaged power plug or loose wall outlet.

• Do not use an extension cord or adapter with this appliance

• Do not, under any circumstances, cut, modify, remove, or otherwise defeat the

grounding (third) prong from the power cord. If the plug and the outlet do not

match or you have any doubt, have a qualied electrician install the proper

outlet. The customer should have the wall receptacle and circuit checked by a

qualied electrician to make sure the receptacle is properly grounded.

• NEVER connect ground wire to plastic plumbing lines, gas lines, or water pipes.

CAUTION

Failure to follow these instructions can result in death, re, or electrical shock.

Additional installation requirements for mobile homes

The installation of appliances designed for mobile home installation must conform

with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280 (formerly the Federal Standard for Mobile Home Construction and Safety,

Title 24, HUD, Part 280) or, when such standard is not applicable, the Standard

for Manufactured Home Installations, latest edition (Manufactured Home Sites,

Communities and Set-Ups), ANSI A225.1, latest edition, or with local codes. In

Canada, mobile home installation must be in accordance with the current CAN/CSA

Z240/MH Mobile Home Installation Code.

Installation instructions

Installing your gas cooktop

IMPORTANT:

Please read the following instructions, as well as the Important Safety Instructions

section at the front of this manual, completely and carefully BEFORE installing

and/or operating the gas cooktop. Improper installation, adjustment, service, or

maintenance can cause personal injury or property damage.

NOTE

To ensure proper installation, we strongly recommend that you hire a professional

installer.

Step 1. Unpack the cooktop

Remove all packaging materials. Failure to remove packaging materials could

result in damage to the appliance.

Inventory all loose parts against the Parts supplied components listed on page 8.

Check for shipping damage and/or missing parts. Any damage and/or missing

parts should be reported to your local retailer.

Step 2. Installing the cooktop.

Rubber

iQ Connect

module

CAUTION

• When inserting the cooktop into the cutout

opening, do not remove the rubber piece

protecting iQ Connect module. Protecting

rubber piece should be removed after

carefully inserting the cooktop.

iQ Connect

module

• When mounting the cooktop, make sure to

insert the cooktop with the front side rst.

Inserting from the rear may damage the

Wi-Fi module.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 14 2020-05-27 �� 11:00:34

English 15

Installation instructions

1. Locate electrical outlet and gas shut-off

valve beneath cabinet.

2. Apply the foam tape around the edge of

the cutout opening. Do not overlap the

foam strips.

• The foam strip helps avoid damage

to the underside of the cooktop from

debris and helps the cooktop sit at on

uneven counters.

3. Protect surface of cooktop

• Place a towel or tablecloth onto the

countertop.

Correct installation

4. With bottom side rst, gently put the

cooktop down. Then, slightly lift up the

rear to remove the protective rubber for

the Wi-Fi module.

• Make sure the front of the countertop is

parallel to the cooktop

• Make nal check that all required

clearances are met.

Front of unit

Gas inlet

Power cord

Hold Down Bracket Installation

Hold down

bracket holes

5. Secure the cooktop to the countertop

using the two provided hold-down

brackets as shown.

Hold down bracket install guide

M4 L10 screw

M4 L16 screw

Case 1.

Countertop

Side wall of

undercounter

cabinet

Hold down

bracket

W

3

/16 L75 screw

Case 2.

Countertop

Chassis

Hold down

bracket

Chassis

M4 L10 screw

NOTE

iQ Connect module can/must be detached before installation of the cooktop in

folowing cases:

• The consumer doesn’t need to iQ Connect function.

• Installation is not possible because the iQ Connect module protrudes against the

rear wall of the countertop.

• The downdraft hood is installed and protrudes against the iQ Connect module.

The Cover must be installed in place of iQ Connect module if iQ Connect module

has been removed. Please read following instructions on how to detach iQ Connect

module.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 15 2020-05-27 �� 11:00:35

16 English

Installation instructions

Rubber

1. Remove screws from all 5 burner cups

and 4 screws from the cooktop frame.

Remove the rubber protecting iQ Connect

module. Pull out all knob dials and lift up

to remove the frame cooktop.

iQ Connect module

2. Detach iQ Connect module from case

burner. Disconnect wire connector from

the PCB.

Cover

3. Install supplied cover in place of

iQ Connect module.

Top view

Insert the wire connector

Wire connector

4. Insert the wire connector diagonally into

the cover. Make sure it ts rmly.

5. Return all burner cups and cooktop frame

to original position, reinstall all knob

dials.

Step 3. Connect the cooktop to gas supply

Shut off the main gas supply valve before disconnecting the old cooktop and leave

it off until the new hookup has been completed. Don’t forget to relight the burner

on other gas appliances when you turn the gas back on.

Because hard piping restricts movement of the cooktop, the use of a CSA

International-certied exible metal appliance connector is recommended unless

local codes require a hard-piped connection.

WARNING

If the information in this manual is not followed exactly, a re or explosion may

result, causing death, personal injury, or property damage.

– Do not store or use gasoline or other ammable vapors and liquids in the

vicinity of this or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

• DO NOT light a match, candle, or cigarette.

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your building.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 16 2020-05-27 �� 11:00:35

English 17

Installation instructions

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

– Installation and service must be performed by a qualied installer, service

agency, or gas supplier.

– Do not install the cooktop without also installing the included gas regulator. Do

not use the cooktop without the regulator installed.

– Ensure that the arrow on the regulator points in the direction of the gas ow,

towards the cooktop.

– Do not apply excessive pressure when tightening gas connections and ttings.

– Test the gas lines for leaks as instructed before use. Do not use a ame to check

for leaks.

Never use an old connector when installing a new cooktop. If the hard-piping

method is used, you must carefully align the pipe; the cooktop cannot be moved

after the connection is made.

To prevent gas leaks, apply pipe-joint compound or wrap pipe-thread tape with

Teon on all male (external) pipe threads.

1. Attach the gas pressure regulator (included with the cooktop) to the cooktop

pipe nipple inlet. For tight installations, the regulator may be installed upstream

from the pipe nipple, anywhere between the shut-off valve and the cooktop.

For best performance, minimize gas pressure loss by attaching the regulator as

close as possible to the cooktop gas inlet.

2. Complete connection of the gas supply to the cooktop by installing a exible

gas line between the pressure regulator and the shut-off valve.

WARNING

Do not exceed 25 ft-lbs of torque when making gas line connections.

Overtightening may crack the pressure regulator resulting in a gas leak.

Flexible connector hookup

Installer: Inform the consumer of the location of the gas shut-off valve.

Adapter

Flex

Connector

(6-ft max.)

Adapter

Gas Shut-Off Valve

0.5-in or 0.75-in

Gas Pipe

Gas Flow into Cooktop

Pressure

Regulator

Tubing Line

to Cooktop

Control

Manifold

NOTE

The gas shut-off valve should be installed

in an accessible location in the gas piping,

external to the appliance, for the purpose

of turning on or shutting off the gas to the

appliance.

Step 4. Check for gas leaks.

WARNING

To prevent death, personal injury, explosion, and/or re hazard, DO NOT use a

ame to check for gas leaks.

When using test pressures greater than ½ psig to pressure-test the gas supply

system of the residence, disconnect the cooktop and individual shut-off valve

from the gas supply piping. When using test pressures of ½ psig or less to test

the gas supply system, simply isolate the cooktop from the gas supply system by

closing the individual shut-off valve.

1. When all connections have been made, make sure all cooktop controls are in the

off position and turn on the main gas supply valve.

2. Use a liquid leak detector at all joints and connections to check for leaks in the

system.

3. Tighten all connections if necessary to prevent gas leakage in the cooktop or

supply line.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 17 2020-05-27 �� 11:00:36

18 English

Installation instructions

Step 5. Electrical connections.

WARNING

• Disconnect all electrical power of the main circuit breaker or fuse box before

installing.

• BEFORE OPERATING OR TESTING, follow the grounding requirements on pages 14

in this manual. Improper connection of the grounding plug can result in a rick of

electric shock.

• All gas cooktops come with a power cord. The power cord is connected to the

bottom of the cooktop. Please review “Electrical requirements” on pages 13.

• The electrical system, including the power cord, is preinstalled and prewired at

the factory. Altering any part of this system may result in a short or overload.

1. Plug in the power cord. Make sure the outlet meets local or national electrical

codes as referenced on pages 13.

2. Check the gas supply line to make sure it did not get damaged and it stayed

connected during positioning.

Step 6. Assemble the cooktop burners.

CAUTION

• Do not operate the cooktop burners without all burner parts in place.

• Be careful not to push in any cooktop controls while removing the cooktop

burner. A slight electrical shock might result which could cause you to knock

over hot cookware.

• Do not remove the top or touch the electrode of any burner while another

burner is turned on. Electrical shock might result.

1. Position cooktop burner heads on top of

the cooktop burner manifolds as shown

on the right. The electrodes will t into

the slot in the bottom of the heads. Make

sure the cooktop burner heads are at

and parallel with the cooktop.

2. Place the matching size caps on top of

each cooktop burner head.

Dual Burner head

1. As shown, insert the marked area of

burner head into the matching area of

burner cup so that they line up.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 18 2020-05-27 �� 11:00:36

English 19

Installation instructions

2. Install the burner head so that the

electrode passes through the opening for

the electrode. Make sure the burner head

lies at on the stove top.

Round Burner head

1. Orient the burner head so that the

opening for the electrode lines up with

the electrode.

2. Install the burner head so that the

electrode passes through the opening for

the electrode. Make sure the burner head

lies at on the stove top.

Burner Head

CAUTION

Make sure all burner components (heads

and caps) are reinstalled properly. They

will be stable and rest at when correctly

installed.

Burner Cap

1. Match the burner caps to the burners by

size, and then re-install the caps on the

burner heads.

CAUTION

Make sure each cap is re-installed on the

correct burner head, is centered on the

burner head, and lies at.

Burner cap

CAUTION

Make sure all burner components (heads

and caps) are reinstalled properly. They

will be stable and rest at when correctly

installed.

Top Bottom

NOTE

The precise simmer burner (RR) cap and

the inner Dual burner (Center) cap are

interchangeable.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 19 2020-05-27 �� 11:00:38

20 English

Installation instructions

Step 7. Check the ignition of cooktop burners

Check the operation of all cooktop burners after the cooktop has been installed

and assembled, gas supply lines have been carefully checked for leaks, and

electrical power cord has been plugged in.

HI

LO

OFF

2

1

To turn on a cooktop burner

1. Push in and turn the control knob for that

cooktop burner to the Lite position. The

“clicking” sound indicates the electronic

ignition system is operating properly. The

burner will light in about 4 seconds, after

the air has been purged from the supply

line .

2. After the burner lights, turn the control

knob to the desired setting. The “clicking”

sound will stop and the ame height will

change from Max. to Min. during turning

the control knob.

3. Repeat steps 1 and 2 to check the

operation of each cooktop burner in

succession.

NOTE

• If the burner does not light within 4 seconds, turn the knob off and wait one

minute before trying again.

• When you push in and turn the control knob, all spark igniters will make a series

of sparks, but only the burner turned to Lite will light.

Step 8. Checking the ame quality.

All combustion ames need to be visually checked to determine their ame

quality.

CAUTION

If you attempt to measure the ame, please use caution. Burns could result.

2

3

1

1. Soft blue ames—Normal for natural gas

operation.

2. Yellow tips on outer cones—Normal for

LP gas operation.

3. Yellow ames—Abnormal for any gas

operation; call for service.

NOTE

If burner ame looks like 3, the cooktop

should not be used until it is serviced. Call

for service. Normal burner ames shall look

like 1 or 2, depending on the gas type you

use.

Install_DTG36P875N_DG68-01286A-00_EN+MES+CFR.indb 20 2020-05-27 �� 11:00:38

La page charge ...

Samsung DTG36P875NS Guide d'installation

Ce manuel convient également à

Samsung DTG36P875NS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents