HP AlphaServer DS25 Manuel utilisateur

Taper
Manuel utilisateur
AlphaServer DS25
Field Upgrade to DS25 Model B
Order Number: EK-H7911-UP. A01
This manual is for persons upgrading an AlphaServer DS25
system to DS25 Model B.
Hewlett-Packard Company
March 2003
© 2003 Hewlett-Packard Company.
HP shall not be liable for technical or editorial errors or omissions contained herein. The information
in this document is provided “as is” without warranty of any kind and is subject to change without
notice. The warranties for HP products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as constituting an additional
warranty.
FCC Notice
This equipment generates, uses, and may emit radio frequency energy. The equipment has been type
tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC
rules, which are designed to provide reasonable protection against such radio frequency interference.
Operation of this equipment in a residential area may cause interference in which case the user at his
own expense will be required to take whatever measures may be required to correct the interference.
Any modifications to this device—unless expressly approved by the manufacturer—can void the
user’s authority to operate this equipment under part 15 of the FCC rules.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are
not expressly approved by Hewlett-Packard Company may void the user's authority to operate the
equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods
in order to maintain compliance with FCC Rules and Regulations.
Taiwanese Notice
Japanese Notice
Canadian Notice
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Avis Canadien
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
European Union Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low
Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms (in brackets are
the equivalent international standards):
EN55022 (CISPR 22) - Electromagnetic Interference
EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity
EN60950 (IEC950) - Product Safety
Warning!
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
Achtung!
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses
Gerätes Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für entsprechende
Gegenmaßnahmen verantwortlich ist.
Attention!
Ceci est un produit de Classe A. Dans un environnement domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l'utilisateur de prendre les mesures spécifiques
appropriées.
Contents
Preface .......................................................................................................................... vii
Chapter 1 Upgrade
1.1 Overview ............................................................................................... 1-1
1.2 Disassembly Procedure ......................................................................... 1-2
1.3 Installation Procedure........................................................................... 1-6
v
Preface
Intended Audience
This manual is for persons ugrading an AlphaServer DS25 to DS25 Model B.
Document Structure
This manual has one chapter.
Chapter 1, Upgrade, Provides an overview of the upgrade procedure and
step by step instructions to convert and AlphaServer DS25 system to DS25
Model B.
vii
Documentation Titles
Table 1 HP AlphaServer DS25 Documentation
Title Order Number
User Documentation Kit
Owner’s Guide
Documentation CD (6 languages)
Maintenance Kit
Service Guide
Loose Piece Items
Basic Installation Card
Rackmount Installation Guide
Rackmount Installation Template
AlphaServer DS25 in a 9000 Series
Cabinet Installation Information
AlphaServer DS25 Field Upgrade to
DS25 Model B (this document)
QA–6WEAA–G8
EK–DS250–UG
AG– RT2DA –TS
QA–6WEABG8
EK–DS250SV
EKDS250PD
EKDS250RG
EKDS250TP
EKBA57RIN
EK-H7911-UP
Information on the Internet
Visit the AlphaServer Web site at www.compaq.com/alphaserver/ for service
tools and more information about the AlphaServer DS25 system.
viii
Chapter 1
Upgrade
1.1 Overview
This procedure is to be used to install the 500-watt power supply upgrade to the
AlphaServer DS25 system. The old 375-watt power supplies are NOT
mechanically interchangeable with the new 500-watt units so therefore, they
will not fit into the system after this upgrade is complete. The upgrade kit part
number is 3X-H7911-UP and contains the following items:
Three 30-10047-01 500-watt power supplies
One 70-41154-01 500-watt PS backplane assembly
Four 74-62829-01 tubular spacers
This procedure assumes that the system has been powered down and removed
from the rack or pedestal mounting, and that the system enclosure is laying on
its right side.
HINT. A 10-inch long #1 Phillips screwdriver is the recommended tool for
removing and installing the power supply backplanes. It is quite helpful if the
tip of the screwdriver is magnetized!
First the old power supplies and power supply backplane are removed and then
the new power supply backplane and 3, 500 watt power supplies are installed.
Upgrade 1-1
1.2 Disassembly Procedure
Follow these steps to disassemble the AlphaServer DS25 in preparation for
installing the upgrade. If needed, detailed information on the first four steps
may be found in the AlphaServer DS25 Owner’s Guide, EK-DS250-UG, or the
AlphaServer DS25 Service Guide, EK-DS250-SV.
1. Remove the top cover .
2. Remove the hard disks in the storage cage.
3. Loosen the thumbscrews on the front access door in front of the power
supplies and remove the door.
4. Remove the 375-watt power supplies and PS filler, if present.
1-2 AlphaServer DS25 Field Upgrade to DS25 Model B
Upgrade 1-3
5. Remove the brace
on top of the storage cage by removing one M3x6mm
screw
.
6. Remove the storage cage
by removing the four M3x10mm screws in the
front and disconnect the three cables
that are plugged into the rear of the
storage cage.
7. Cut the tie wrap on the cable harness, just to the top right of the power
supply backplane.
1-4 AlphaServer DS25 Field Upgrade to DS25 Model B
2
3
3
3
2
4
3
1
1
MR0491
8. Disconnect the four cables
that are plugged into the power supply
backplane
.
9. Remove the power supply backplane by removing the four M3x12mm screws
in the four corners of the power supply backplane.
10. Swing out the left side of the backplane to allow hand access to the bottom
left corner of the power supply backplane.
11. Disconnect the 3-pin and 4-pin Mate-N-Lok connectors
on the backside
of the power supply backplane.
12. Remove the old power supply backplane assembly.
Upgrade 1-5
1.3 Installation Procedure
Follow these steps to install and re-assemble the AlphaServer DS25 Model B
system.
2
3
2
2
4
5
1
2
MR0492
1. Find the four threaded standoffs that were used to mount the old power
supply backplane. Slip four tubular spacers
over these four standoffs.
2. Position the new 500-watt power supply backplane
over and on top of the
spacers on the right side while holding the left side out away from the
center wall of the enclosure. Connect the 3-pin and 4-pin Mate-N-Lok
connectors
to the mating connectors that are part of the new
backplane assembly.
1-6 AlphaServer DS25 Field Upgrade to DS25 Model B
Upgrade 1-7
1
3
7
4
5
2
MR0493
6
3. Push these two connectors and harnesses back into the opening at the
bottom left corner of the center wall
where the original AC harnesses
emerged.
4. Making sure that wiring is not pinched between the backplane and the
center wall, push the left side of the new backplane into place.
5. Holding the backplane in place, start one of the M3x12mm screws
in the
top left spacer/standoff, but do not tighten it yet.
6. Start the bottom left M3x12mm screw into the spacer/standoff.
7. Moving to the top right, start an M3x12mm screw here
. Again, do not
tighten it yet.
8. Start an M3x12mm screw
at the bottom right of the backplane.
9. With all four screws now in position, push against the backplane to seat it
properly against the center wall and tighten all 4 screws holding the
backplane in place.
10. Install the four cables
that plug into the power supply backplane.
11. Install the three 500-watt power supplies
.
12. Reinstall the storage cage into the enclosure opening loosely. Reattach the
three cables to the rear of the storage cage.
13. Slide the storage cage into place and secure it with the four M3X10mm
screws.
14. Reinstall the storage cage brace and M3x6mm screw on top of the storage
cage.
15. Reinstall the access door in front of the power supplies. Tighten the
thumbscrews finger tight.
16. Reinstall the hard disks into the storage cage.
17. Replace the top cover.
18. If possible, perform simple power up checks before mounting the system
back into the rack or pedestal.
1-8 AlphaServer DS25 Field Upgrade to DS25 Model B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

HP AlphaServer DS25 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues