Husqvarna 967284202 Mode d'emploi

EE

nn

gg

ll

ii

ss

hh

((

22

--

22

33

))

FF

rr

ee

nn

cc

hh

((

22

44

--

4

44

55

))

SS

pp

aa

nn

ii

ss

hh

((

44

66

--

66

77

))

525BX

Operator’s manual

Manuel d’utilisation

Manual de instrucciones

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine.

Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina.

KEY TO SYMBOLS

2 – English

Symbols

WARNING! The machine can be a

dangerous tool if used incorrectly or

carelessly, which can cause serious or

fatal injury to the operator or others.

Please read the operator’s manual

carefully and make sure you

understand the instructions before

using the machine.

Always wear:

• Hearing protection

• Approved eye protection

• A breathing mask should be used

when there is a risk of dust.

Gloves should be worn when necessary.

The blower can forcibly throw

objects that can bounce back.

This can result in serious eye

injuries if the recommended

safety equipment is not used.

The blower operator must

make sure that no

bystanders or animals

come nearer than 15

metres. Whenever several

operators are working in the

same work area, they

should maintain a safe

distance of at least 15

metres from one another.

Air purge

Refuelling.

Choke lever in ”closed position”.

The rating plate showing

serial number.

yyyy

is

the production year,

ww

is the productionweek.

Other symbols/decals on the machine refer to special

certiﬁcation requirements for certain markets.

The engine is switched off by moving the

stop switch to the stop position.

CAUTION! The stop switch

automatically returns to the start

position. In order to prevent

unintentional starting, the spark plug

cap must be removed from the spark

plug when assembling, checking and/or

performing maintenance.

Regular cleaning is required.

Visual check.

yyyywwxxxxx

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

CONTENTS

English

–

3

Contents Note the following before

starting:

Please read the operator’s manual carefully.

This decal certiﬁes that the product has been approved in

accordance with American exhaust emissions

requirements EPA Ph III and CARB Tier III. The

Emissions Compliance Period referred to on the

Emissions Compliance label indicates the numbers of

operating hours for which the engine has been shown to

meet Federal and California emission requirements.

Husqvarna AB has a policy of continuous product

development and therefore reserves the right to modify

the design and appearance of products without prior

notice.

The blower is only designed for blowing lawns, pathways,

asphalt roads and the like.

For customer assistance, contact us at our website:

www.husqvarna.com

KEY TO SYMBOLS

Symbols ................................................................ 2

CONTENTS

Contents ............................................................... 3

Note the following before starting: ........................ 3

INTRODUCTION

Dear customer! ..................................................... 4

WHAT IS WHAT?

What is what on the blower? ................................ 5

GENERAL SAFETY PRECAUTIONS

General ................................................................. 6

SAFETY INSTRUCTIONS

Personal protective equipment ............................. 8

Machine

′

s safety equipment ................................. 8

ASSEMBLY

Blow pipe .............................................................. 11

FUEL HANDLING

Fuel ...................................................................... 12

Fueling .................................................................. 13

STARTING AND STOPPING

Starting and stopping ........................................... 14

WORKING TECHNIQUES

General working instructions ................................ 16

MAINTENANCE

Carburetor ............................................................ 18

Mufﬂer .................................................................. 18

Cooling system ..................................................... 18

Spark plug ............................................................ 18

Air ﬁlter ................................................................. 19

Maintenance schedule ......................................... 20

TECHNICAL DATA

Technical data ...................................................... 21

FEDERAL AND CALIFORNIA EMISSIONS

CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS 22

!

WARNING! Long-term exposure to noise

can result in permanent hearing

impairment. So always use approved

hearing protection.

!

WARNING! Under no circumstances may

the design of the machine be modiﬁed

without the permission of the

manufacturer. Always use genuine

accessories. Non-authorized

modiﬁcations and/or accessories can

result in serious personal injury or the

death of the operator or others.

Your warranty may not cover damage or

liability caused by the use of non-

authorized accessories or replacement

parts.

!

WARNING! A blower is a dangerous tool

if used carelessly or incorrectly and can

cause serious, even fatal injuries. It is

extremely important that you read and

understand the contents of this

Operator’s manual.

4 – English

INTRODUCTION

Dear customer!

Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,

when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production

of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-

powered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different

products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst

motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working

today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our

highest priority. We develop, manufacture and market high quality motor driven products for forestry and gardening as

well as for building and construction industry.

Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the

retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this

operator

′

s manual as a valuable document. By following its

′

content (using, service, maintenance etc) the life span and

the second-hand value of the machine can be extended. If you ever lend or sell this machine, make sure that the

borrower or buyer gets the operator

′

s manual, so they will also know how to properly maintain and use it.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

English – 5

WHAT IS WHAT?

What is what on the blower?

11

12

1

6

7

9

5

4

2

10

17

3

19

13

14

8

15

16

18

1 Stop switch

2 Throttle control

3 Throttle settings control

4 Control handle/Operating handle

5 Handle

6 Choke control

7 Primer bulb

8 Starter handle

9 Tube clamp screw

10 Intermediate pipe

11 Round nozzle

12 Flat nozzle

13 Spark plug

14 Fuel cap

15 Air ﬁlter

16 Mufﬂer

17 Air intake screen

18 Operator’s manual

19 Combination spanner

GENERAL SAFETY PRECAUTIONS

6 – English

General

!

WARNING! Overexposure to vibration

can lead to circulatory damage or nerve

damage in people who have impaired

circulation. Contact your doctor if you

experience symptoms of overexposure

to vibration. Such symptoms include

numbness, loss of feeling, tingling,

pricking, pain, loss of strength, changes

in skin colour or condition. These

symptoms normally appear in the

ﬁngers, hands or wrists. These

symptoms may be increased in cold

temperatures. In order to reduce the risk

of whiteﬁnger disease, the following

precautions are strongly recommended.

Wear thick anti-vibration gloves.

Take more than 5 minutes of break in

warm place frequently.

Maintain a ﬁrm grip at all times, but do

not squeeze the handles with constant,

excessive pressure.

If you feel discomfort, redness and

swelling of your ﬁngers or any other part

of your body, see a doctor before getting

worse.

IMPORTANT!

The blower is only designed for blowing lawns,

pathways, asphalt roads and the like.

Do an overall inspection of the machine before use, see

maintenance schedule.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect

your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions

under the heading ”Personal protective equipment”.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts.

Loose clothes, jewellery or long

hair can be caught in moving parts.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Never use a machine that is faulty. Carry out the safety

checks, maintenance and service instructions

described in this manual. Some maintenance and

service measures must be carried out by trained and

qualiﬁed specialists. See instructions under the heading

Maintenance.

All covers and guards must be ﬁtted before starting.

Ensure that the spark plug cap and ignition lead are

undamaged to avoid the risk of electric shock.

The blower operator must make sure that no bystanders

or animals come nearer than 15 metres. Whenever

several operators are working in the same work area,

they should maintain a safe distance of at least 15

metres from one another.

Never allow children to use the machine.

Never allow anyone else to use the machine without ﬁrst

ensuring that they have read and understood the

contents of the operator’s manual.

Always check for any objects that may block the air

intake screen before beginning work.

Always contact local authorities and make sure you are

following applicable directives.

Keep all parts of your body away from hot surfaces.

Metallic parts and engine cover reach high tempatures

during operation and doing so could result in serious

burns.

Never remove debris from the inlet screen while the

engine is runing. Contact with rotating blower fan result

in a serious personal injury.

GENERAL SAFETY PRECAUTIONS

English

–

7

Starting

• Never start the machine indoors. Exhaust fumes can

be dangerous if inhaled.

• Observe the surroundings and ensure that no people

or animals can come into contact with the blower.

Place the machine on the ground, press the machine

body against the ground with your right hand (NOTE! Not

your foot). Now grasp the starter handle with your left

hand and then pull quickly and ﬁrmly.

Fuel safety

• Always use a fuel container with an anti-spill valve.

• Never refuel the machine while the engine is running.

Always stop the engine and let it cool for a few minutes

before refueling.

• Make sure there is plenty of ventilation when refuelling

or mixing fuel (gasoline and 2-stroke oil).

• Avoid all skin contact with fuel. Fuel is a skin irritant

and may even cause skin changes.

• Move the machine at least 10 ft (3 m) from the

refuelling point before starting it.

• Never start the machine:

- If you have spilled fuel on it. Wipe off the spillage and

allow remaining fuel to evaporate.

- If you have spilled fuel on yourself or your clothes,

change your clothes. Wash any part of your body that has

come in contact with fuel. Use soap and water.

- If the machine is leaking fuel. Check regularly for leaks

from the fuel cap and fuel lines.

Transport and storage

• Store and transport the machine and fuel so that there

is no risk of any leakage or fumes coming into contact

with sparks or open ﬂames, for example, from

electrical machinery, electric motors, electrical relays/

switches or boilers.

• When storing and transporting fuel always use

approved containers intended for this purpose.

• When storing the machine for long periods the fuel

tank must be emptied. Contact your local gas station

to ﬁnd out where to dispose of excess fuel. Empty the

fuel tank and press the primer until all fuel has been

emptied. Remove the spark plug and drop a spoon of

2-stroke oil in the cylinder. Turn over the engine a few

times and then put the spark plug back in place.

• Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

• Secure the machine during transport.

• Store the machine in a dry, cool, well-aired and dust-

free location. Store the machine out of reach of

children.

!

WARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants. To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants consult their physician and the

medical implant manufacturer before

operating this machine.

Min 3 m

(10 ft)

!

WARNING! Take care when handling fuel.

Bear in mind the risk of ﬁre, explosion

and inhaling fumes.

SAFETY INSTRUCTIONS

8 – English

Personal protective equipment

• Gloves should be worn when necessary.

• Wear hearing protection that provides adequate noise

reduction.

• Always wear approved eye protection. If you use a

visor then you must also wear approved protective

goggles. Approved protective goggles must comply

with standard ANSI Z87.1 in the USA or EN 166 in EU

countries. Blows from branches or objects that are

thrown can damage the eyes.

• Wear sturdy, non-slip boots.

• Always wear heavy, long pants, boots, gloves, and a

long-sleeve shirt. To reduce the risk of injury

associated with objects being drawn into rotating

parts, do not wear loose clothing, scarves, jewelry,

etc. Secure hair so it is above shoulder level.

• A breathing mask should be used when there is a risk

of dust.

• Always have a ﬁrst aid kit nearby.

Machine

′

s safety equipment

This section describes the machine

′

s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

Stop switch

Use the stop switch to switch off the engine.

Remove the ignition cable and the spark plug to carry out

inspection and maintenance.

!

WARNING! You must use approved

personal protective equipment whenever

you use the machine. Personal protective

equipment cannot eliminate the risk of

injury but it will reduce the degree of

injury if an accident does happen. Ask

your dealer for help in choosing the right

equipment. Please read the operator’s

manual carefully and make sure you

understand the instructions before using

the machine.

!

WARNING! Listen out for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

!

WARNING! Never use a machine that has

faulty safety equipment! Carry out the

inspection, maintenance and service

routines listed in this section.

SAFETY INSTRUCTIONS

English

–

9

Vibration damper

Your machine is equipped with a vibration damping

system that is designed to reduce vibration and make

operation easier.

Mufﬂer

The mufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user.

A mufﬂer ﬁtted with a catalytic converter is also designed

to reduce harmful exhaust gases.

In countries that have a warm and dry climate there is a

signiﬁcant risk of ﬁre. We therefore ﬁt certain mufﬂers with

a spark arrestor screen. Check whether the mufﬂer on

your machine is ﬁtted with this kind of screen.

For mufﬂers it is very important that you follow the

instructions on checking, maintaining and servicing your

machine.

Never use a machine that has a faulty mufﬂer.

Regularly check that the mufﬂer is securely attached to

the machine.

!

WARNING! Overexposure to vibration

can lead to circulatory damage or nerve

damage in people who have impaired

circulation. Contact your doctor if you

experience symptoms of overexposure

to vibration. Such symptoms include

numbness, loss of feeling, tingling,

pricking, pain, loss of strength, changes

in skin colour or condition. These

symptoms normally appear in the

ﬁngers, hands or wrists. The risk

increases at low temperatures.

SAFETY INSTRUCTIONS

10 – English

If the mufﬂer on your machine is ﬁtted with a spark

arrestor screen this must be cleaned regularly. A blocked

screen will cause the engine to overheat and may lead to

serious damage.

NOTE!

Make sure that the spark arrestor is screwed in place

correctly.

Air ﬁlter

Never use the leaf blower without an air ﬁlter or with a

damaged or deformed ﬁlter element as unﬁltered, dusty

air can quickly destroy the engine.

!

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.

This also applies at idle speed. Contact

can result in burns to the skin.

Remember the risk of ﬁre!

!

WARNING! The inside of the mufﬂer

contain chemicals that may be

carcinogenic. Avoid contact with these

elements in the event of a damaged

mufﬂer.

ASSEMBLY

English

–

11

Blow pipe

The blower tube has a pegged slot mounting system to

the unit.

• To install or remove the blower tube, the tube clamp

screw must be loosen.

• Align slot in the blower air outlet with the raised rib on

the intermediate tube and insert tube until the holes in

the tube and housing align.

• Re–tighten the tube clamp bolt.

1 Tube clamp screw

2 Intermediate tube

3 Round nozzle

4 Flat nozzle

3

2

4

1

FUEL HANDLING

12 – English

Fuel

CAUTION! The machine is equipped with a two-stroke

engine and must always be run using a mixture of

gasoline and two-stroke engine oil. It is important to

accurately measure the amount of oil to be mixed to

ensure that the correct mixture is obtained. When mixing

small amounts of fuel, even small inaccuracies can

drastically affect the ratio of the mixture.

Gasoline

CAUTION! Always use high grade oil mixed gasoline

(minimum 87 RON).

• When working at continuous high revs a higher octane

rating is recommended. Use good quality unleaded

gasoline.

•

This engine is certiﬁed to operate on unleaded

gasoline.

• The lowest recommended octane rating is 87. If you

run the engine on lower octane rating than 87 so-

called “knocking“ can occur. This leads to an

increased engine temperature, which can result in a

serious engine breakdown.

Husqvarna alkylate fuel

Husqvarna recommends the use of Husqvarna alkylate

fuel for best performance. Husqvarna alkylate fuel is not

available in all markets.

Ethanol blended fuel, E10 may be used (max 10%

ethanol blend). Using ethanol blends higher than E10 will

create lean running condition which can cause engine

damage.

Two-stroke oil

• For best results and performance use HUSQVARNA

two-stroke oil, which is specially formulated for our

two-stroke engines. Mixture 1:50 (2%).

• If HUSQVARNA two-stroke oil is not available, you

may use another two-stroke oil of good quality that is

intended for air cooled engines. Contact your dealer

when selecting an oil.

• Never use two-stroke oil intended for water-cooled

outboard engines, sometimes referred to as outboard

oil.

• Never use oil intended for four-stroke engines.

Mixing

• Always mix the gasoline and oil in a clean container

intended for fuel.

• Always start by ﬁlling half the amount of the gasoline

to be used. Then add the entire amount of oil. Mix

(shake) the fuel mixture. Add the remaining amount of

gasoline.

• Mix (shake) the fuel mixture thoroughly before ﬁlling

the machine’s fuel tank.

• Do not mix more than one month’s supply of fuel at a

time.

• If the machine is not used for some time the fuel tank

should be emptied and cleaned.

•

This engine is certiﬁed to operate on unleaded

gasoline.

!

WARNING! Always ensure there is

adequate ventilation when handling fuel.

Gasoline, litre Two-stroke oil, litre

2% (50:1)

5

0,10

10

0.42/0,20

15

0,6/0,30

20

0,40

US gallon US ﬂ. oz.

1

2 1/2

6 1/2

5

12 7/8

FUEL HANDLING

English

–

13

Fueling

• Move the machine at least 10 ft (3 m) from the

refuelling point before starting it.

• Clean the area around the fuel cap. Contamination in

the tank can cause operating problems.

• Ensure that the fuel is well mixed by shaking the

container before ﬁlling the tank.

• Check the fuel level before each use and leave space

for the fuel to expand, because the heat from the

engine and the sun may otherwise cause the fuel to

expand and overﬂow.

• Keep the handle dry and free from oil and fuel.

• Always store fuel in an approved container designed

for that purpose.

!

WARNING! Taking the following

precautions, will lessen the risk of ﬁre:

Refuel in a well ventilated area. Never

fuel the machine indoors.

Do not smoke or place hot objects near

fuel.

Always shut off the engine before

refueling.

Always stop the engine and let it cool for

a few minutes before refueling.

When refuelling, open the fuel cap slowly

so that any excess pressure is released

gently.

Tighten the fuel cap carefully after

refueling.

If you have spilled fuel on it. Wipe off the

spillage and allow remaining fuel to

evaporate.

Always move the machine away from the

refueling area and source before

starting.

Min 3 m

(10 ft)

STARTING AND STOPPING

14 – English

Starting and stopping

Starting

Throttle posistion: Set the throttle position setting to the

idling position.

Air purge: Press the air purge repeatedly until fuel begins

to ﬁll the bulb. The bulb need not be completely ﬁlled.

Cold engine

Choke: Set the choke control in the choke position.

Hold the body of the machine on the ground using your

right hand (CAUTION! Not with your foot! ).

Grip the starter handle, slowly pull out the cord with your

left hand until you feel some resistance (the starter pawls

grip), now quickly and powerfully pull the cord. Never

wrap the starter cord around your hand

Repeat pulling the cord until engine attemps to start (or

maximum 5 pulls).

Move choke control down to run position.

Pull the cord until engine starts and gradually operate

throttle trigger for increasing engine speed to operate

speed. Allow the engine to warm for a few minutes.

Warm engine

Use the same starting procedure as for a cold engine but

without setting the choke control in the choke position. If

the engine won’t start after several attempts, close the

choke and repeat pulling the rope.

NOTE!

Air is released as soon as the engine is started, even

when idling.

When the engine fails to start after several attempts due

to overchocking, open the choke and repeat pulling the

rope.

CAUTION! Do not pull the starter cord all the way out and

do not let go of the starter handle when the cord is fully

extended. This can damage the machine.

!

WARNING! Always move the machine

away from the refueling area and source

before starting. Place the machine on a

ﬂat surface.

Make sure no unauthorised persons are

in the working area, otherwise there is a

risk of serious personal injury. The safety

distance is 15 meters (50 ft.).

The machine may only be started in its

complete design. If the machine is

started without all the guards ﬁtted there

is a risk of personal injuries.

STARTING AND STOPPING

English – 15

CAUTION! Do not put any part of your body in marked

area. Contact can result in burns to the skin, or electrical

shock if the spark plug cap has been damaged. Always

use gloves. Do not use a machine with damaged spark

plug cap.

Stopping

Move the throttle trigger to the idling position and press

the stop switch until the engine comes to a complete stop.

CAUTION! The stop switch automatically returns to the

start position. In order to prevent unintentional starting,

the spark plug cap must be removed from the spark plug

when assembling, checking and/or performing

maintenance.

WORKING TECHNIQUES

16 – English

General working instructions

Show consideration to persons in your surroundings by

avoiding using the machine at unsuitable times, such as

late in the evening or early in the morning. To reduce

sound levels, limit the number of pieces of equipment

used at any one time. Read through and follow the simple

directions so that you disturb your surroundings as little as

possible.

• This blower is a hand held type. The blower is held

using the handle by hand. It is operated and controlled

by the handle while operating. The speed of the air jet

is controlled with the throttle. Select the speed that

best suits the application. To avoid holding your ﬁnger

on the throttle all the time when using the blower, the

required throttle can be set with the throttle adjuster

(D). Full throttle is obtained when the throttle adjuster

is pushed in fully.

• Use the blower with the lowest possible throttle. It is

seldom necessary to use full throttle, and many work

procedures can be done at half throttle. A lower

throttle means less noise and less dust, and it is also

easier to keep control over the rubbish collected

together/moved.

• Use a rake or a brush to release rubbish stuck to the

ground.

• Hold the opening of the blower as close to the ground

as possible. Utilise the entire length of the blow pipe

to keep the air current close to the ground.

• Clean up afterwards. Make sure that you have not

blown rubbish into someone’s garden.

• Operate power equipment only at reasonable hours,

not early in the morning or late at night when people

might be disturbed. Comply with times listed in local

ordinances.

Basic safety rules

• No unauthorised persons or animals may be present

in the working area, which is 15 metres.

• Allow the engine to cool before refueling.

• Keep all parts of your body away from hot surfaces.

• Never touch the spark plug or ignition cable while the

engine is running. Touching the spark plug or plug

may result in being subjected to an electrical shock.

• The powerful currents of air can move objects at such

a speed that they can bounce back and cause serious

eye injuries.

• Do not direct the air jet towards people or animals.

• Stop the engine before assembling or dismantling

accessories or other parts.

IMPORTANT! This section considers basic safety rules

when working with blowers. If you encounter a situation

where you are uncertain how to proceed you should ask

an expert. Contact your dealer or your service

workshop. Avoid all usage which you consider to be

beyond your capability.

D

!

WARNING! Be aware of your

surroundings. If anyone approaches your

work area, set the throttle control to the

lowest throttle until the person is at a

safe distance. Direct the blower away

from people, animals, play areas, open

windows and cars etc.

WORKING TECHNIQUES

English – 17

• Do not use the machine in bad weather, such as

dense fog, heavy rain, strong wind, intense cold, etc.

Working in bad weather is tiring and can lead to

dangerous conditions, e.g. slippery surfaces.

• Minimise the blowing time by lightly wetting dusty

areas or using spray equipment.

• Conserve water by using power blowers instead of

hoses for many lawn and garden applications,

including areas such as gutters, screens, patios, grills,

porches and gardens.

• Make sure you can move and stand safely. Check the

area around you for possible obstacles (roots, rocks,

branches, ditches, etc.) in case you have to move

suddenly. Take great care when working on sloping

ground.

• Never put the machine down with the engine running

unless you have it in clear sight.

• Engine exhaust fumes contain carbon monoxide,

which can cause carbon monoxide poisoning. For this

reason you should not start or run the machine

indoors, or anywhere that is poorly ventilated.

• The blower must not be used while on a ladder or

scaffolding.

• CAUTION! Do not use the machine unless you are

able to call for help in the event of an accident.

Basic working techniques

The speed of the air jet is regulated by means of the

throttle. Select the speed best suited for respective tasks.

You can set the throttle position using the throttle position

settings and by doing so not need to hold your ﬁnger on

the throttle all the time you are using the blower. Full

throttle is obtained when the control is held back fully.

• Check that the air intake is not blocked, for example,

by leaves or rubbish. A clogged air intake reduces the

machine’s blowing capacity and increases the

engine’s working temperature, which can result in

engine failure. Stop the engine and remove the object.

• Be aware of the wind direction. Work with the wind to

make your work easier.

• Use the full blower nozzle extension so the air stream

can work close to the ground.

• Always check to be sure that no debris has been

blown onto someone else’s property.

• Never point a blower tube toward an open ﬂame to

avoid the possibility of igniting the unit, causing injury

to yourself or damage to surroundings.

• Using the blower to move large piles is time

consuming and creates unnecessary noise.

• Keep a good balance and a ﬁrm foothold.

• When work is ﬁnished the machine should be stored

vertically.

!

WARNING! Watch out for thrown objects.

Always wear eye protection. Stones,

rubbish, etc. can be thrown up into the

eyes causing blindness or serious injury.

Keep unauthorised persons at a

distance. Children, animals, onlookers

and helpers should be kept outside the

safety zone of 15 m. Stop the machine

immediately if anyone approaches.

!

WARNING! Always stop the engine

before cleaning.

MAINTENANCE

18 – English

Carburetor

Adjustment of the idle speed

Before any adjustments are made, make sure that the air

ﬁlter is clean and the air ﬁlter cover is ﬁtted. Adjust the idle

speed using the idle adjustment screw T, if it is necessary

to readjust.

Recommended idle speed: See the Technical data

section.

Mufﬂer

CAUTION! Some mufﬂers are ﬁtted with a catalytic

converter. See chapter on Technical data to see whether

your machine is ﬁtted with a catalytic converter.

The mufﬂer is designed to reduce the noise level and to

direct the exhaust gases away from the operator. The

exhaust gases are hot and can contain sparks, which may

cause ﬁre if directed against dry and combustible

material.

Some mufﬂers are equipped with a special spark arrestor

screen. If your machine has this type of mufﬂer, you

should clean the screen at least once a week. This is best

done with a wire brush. On mufﬂers without a catalytic

converter the screen should be cleaned weekly, or

replaced if necessary. On mufﬂers ﬁtted with a catalytic

converter the screen should be checked, and if necessary

cleaned, monthly. If the screen is damaged it should be

replaced. If the screen is frequently blocked, this can be

a sign that the performance of the catalytic converter is

impaired. Contact your dealer to inspect the mufﬂer. A

blocked screen will cause the machine to overheat and

result in damage to the cylinder and piston.

CAUTION! Never use a machine with a defective mufﬂer.

Cooling system

To keep the working temperature as low as possible the

machine is equipped with a cooling system.

Clean the cooling system with a brush once a week, more

often in demanding conditions. A dirty or blocked cooling

system results in the machine overheating which causes

damage to the piston and cylinder.

Spark plug

The spark plug condition is inﬂuenced by:

• Incorrect carburetor adjustment.

• An incorrect fuel mixture (too much or incorrect type

of oil).

• A dirty air ﬁlter.

These factors cause deposits on the spark plug

electrodes, which may result in operating problems and

starting difﬁculties.

If the machine is low on power, difﬁcult to start or runs

poorly at idle speed: always check the spark plug ﬁrst

before taking any further action. If the spark plug is dirty,

T

!

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.

This also applies at idle speed. Contact

can result in burns to the skin.

Remember the risk of ﬁre!

MAINTENANCE

English – 19

clean it and check that the electrode gap is 0,026 inch

(0,65 mm). The spark plug should be replaced after about

a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug

type! Use of the wrong spark plug can damage the piston/

cylinder. Check that the spark plug is ﬁtted with a

suppressor.

Air ﬁlter

The air ﬁlter must be regularly cleaned to remove dust

and dirt in order to avoid:

• Carburettor malfunctions.

• Starting problems.

• Loss of engine power.

• Unnecessary wear to engine parts

• Excessive fuel consumption.

1 Foam plastic ﬁlter (urethan ﬁlter)

2 Felt ﬁlter

3 Screen

Clean the ﬁlter every 25 hours, or more regularly if

conditions are exceptionally dusty.

Cleaning the air ﬁlter

Close the choke control by setting the choke into a choke

position.

• Remove the air ﬁlter cover and take out the ﬁlter. Wash

it clean in warm, soapy water. Clean also the inside of

the ﬁlter cover by using air or a brush. Ensure that the

ﬁlter is dry before reﬁtting it.

• Remove the Felt ﬁlter from the ﬁlter holder and gently

brush debris from the ﬁlter.

• Install screen and Felt ﬁlter to the air ﬁlter holder.

• Install the foam ﬁlter in the air ﬁlter cover.

• Install the air ﬁlter cover.

An air ﬁlter that has been in use for a long time cannot be

cleaned completely. The ﬁlter must therefore be replaced

with a new one at regular intervals. A damaged air ﬁlter

must always be replaced. Damaged, very dirty, or fuel-

soaked air ﬁlter must always be replaced.

Air intake screen

Check that the air intake is not blocked, for example, by

leaves or rubbish. A clogged air intake reduces the

machine’s blowing capacity and increases the engine’s

working temperature, which can result in engine failure.

Stop the engine and remove the object.

Fuel ﬁlter

Check the fuel ﬁlter for contamination and the fuel hose

for cracks or other defects. Replace if necessary.

0,65

1

2

3

!

WARNING! Never use the blower if the

screen is not in place. Before use, check

that the screen is in place and

undamaged.

20 – English

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the

Maintenance section.

Maintenance

Daily

maintenance

Weekly

maintenance

Monthly

maintenance

Clean the outside of the machine. X

Make sure the throttle trigger lock and the throttle function

correctly from a safety point of view.

X

Check that the stop switch works correctly. X

Clean the air ﬁlter. Replace if necessary. X

Check that nuts and screws are tight. X

Check that there are no fuel leaks from the engine, tank or fuel

lines.

X

Check the fuel ﬁlter for contamination and the fuel hose for cracks

or other defects. Replace if necessary.

X

Check that all sides of the air intake screen are not blocked. X

Check the starter and starter cord. X

Check that the vibration damping elements are not damaged. X

Clean the outside of the spark plug. Remove it and check the

electrode gap. Adjust the gap to 0.65 mm (.026”), or replace the

spark plug. Check that the spark plug is ﬁtted with a suppressor.

X

Clean the machine’s cooling system. X

Clean or replace the spark arrestor screen on the mufﬂer (only

applies to mufﬂers without a catalytic converter).

X

Clean the outside of the carburettor and the space around it. X

Check the fuel ﬁlter for contamination and the fuel hose for cracks

or other defects. Replace if necessary.

X

Check all cables and connections. X

Replace the spark plug. Check that the spark plug is ﬁtted with a

suppressor.

X

Check and clean the spark arrestor screen on the mufﬂer (only

applies to mufﬂers ﬁtted with a catalytic converter).

X

La page charge ...

Husqvarna 967284202 Mode d'emploi

Husqvarna 967284202 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents