JVC 0305MNMMDWJEIN Manuel utilisateur

ENGLISH

ESPAÑOL

FRANÇAIS

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

LVT1340-001B

[J]

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, référez-vous au manuel séparé.

• This system cannot receive television broadcasts. Use the separately sold TV tuner unit KV-C1000 for

optional television broadcast reception.

• Este sistema no puede recibir emisiones de televisión. Utilice la unidad de sintonizador de TV móvil

KV-C1000 vendido por separado para una recepción opcional de emisiones de televisión.

• Ce système ne peut pas recevoir les émissions de télévision. Utilisez le module de tuner de télévision

mobile KV-C1000 vendu séparément afin de pouvoir recevoir les émissions de télévision.

9-INCH WIDESCREEN MONITOR

WITH DVD PLAYER KV-MRD900

MONITOR DE PANTALLA ANCHA DE 9 PULGADAS

CON REPRODUCTOR DVD KV-MRD900

MONITEUR COULEUR A ECRAN LARGE DE 9 POUCES

AVEC LECTEUR DE DVD KV-MRD900

For customer Use:

Enter below the Model

No. and Serial No. which

are located on the top or

bottom of the cabinet.

Retain this information for

future reference.

Model No.

Serial No.

Cover_KV-MRD900[J]ff.indd 2Cover_KV-MRD900[J]ff.indd 2 5/16/05 11:06:29 AM5/16/05 11:06:29 AM

2

ENGLISH

WARNINGS

• DO NOT INSTALL THE MONITOR IN A

LOCATION WHICH OBSTRUCTS DRIVING,

VISIBILITY, SAFETY DEVICE FUNCTION

SUCH AS AIR BAGS OR WHICH IS

PROHIBITED BY APPLICABLE LAWS AND

REGULATIONS.

• There may be legal regulations defining the

permissible installation locations for the monitor

which differ by country or by state. Be sure

to install the monitor in a correct location

according to such laws.

• The driver must not operate the monitor while

driving.

* Stop your vehicle in a safe location when

operating the monitor.

• The driver must not watch the television or

playback pictures while driving.

If the driver does it while driving, it may lead to

carelessness and cause an accident.

• Keep the monitor at an appropriate sound level

while driving.

Driving with the sound at a level that prevents

you from hearing sounds outside of and around

the vehicle may cause an accident.

• Be sure not to let the monitor fall or be strongly

impacted since this may cause a malfunction or

fire.

• Do not use the monitor with the engine off.

Doing so with the engine off will consume

battery power and may prevent the engine from

starting.

• When not in use, close the liquid crystal panel

and store it into the compartment.

• Do not touch the surface of the liquid crystal

panel directly.

• Do not hang any object on the monitor or hang

down, as this may damage the monitor.

CAUTION:

This monitor should be used on DC 12 V only. To

prevent electric shocks and fire hazards, DO NOT

use any other power source.

CAUTION:

This product has a fluorescent lamp that

contains a small amount of mercury. It

also contains lead in some components.

Disposal of these materials may be

regulated in your community due to

environmental considerations.

For disposal or recycling information

please contact your local authorities, or

the Electronics Industries Alliance:

http://www.eiae.org./

Installation requires some special

knowledge.

Do not install the monitor yourself.

Consult a dealer having special

knowledge of this kind for safe and

reliable installation.

CAUTIONS on the supplied headphones

—KS-HP2:

• DO NOT leave the headphones in a place

exposed to direct sunlight for a long

time, such as a dashboard, as they may be

damaged.

• Keep the headphones away from a cellular

phone to avoid interference.

• DO NOT turn off the power with the

volume set at high level, as the sudden

blast of sound can damage your hearing

and/or headphones next time you use the

headphones.

• If you experience a ringing in your

ears, reduce volume or stop using the

headphones.

EN02-06_KV-MRD900[J]f.indd 2EN02-06_KV-MRD900[J]f.indd 2 05.3.19 11:28:22 AM05.3.19 11:28:22 AM

3

ENGLISH

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

This product incorporates copyright

protection technology that is protected

by U.S. patents and other intellectual

property rights. Use of this copyright

protection technology must be authorized

by Macrovision, and is intended for home

and other limited viewing uses only unless

otherwise authorized by Macrovision.

Reverse engineering or disassembly is

prohibited.

Caution on volume setting:

Discs produce very little noise compared

with other sources. Lower the volume

before playing a disc to avoid damaging

the speakers by the sudden increase of the

output level.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave

all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.

Avoid direct exposure to beam.

EN02-06_KV-MRD900[J]f.indd 3EN02-06_KV-MRD900[J]f.indd 3 05.3.19 11:28:23 AM05.3.19 11:28:23 AM

4

ENGLISH

How to read this manual

The following methods are used to make the

explanations simple and easy-to-understand:

• Some related tips and notes are explained in

“More about this monitor” (see pages

33 – 35).

• Button operations are mainly explained with

the illustrations as follows:

Press briefly.

Press repeatedly.

Press either one.

Press and hold until

your desired response

begins.

Press and hold both

buttons at the same

time.

How to reset your monitor

This will reset the microcomputer. Your preset

adjustments will also be erased.

How to forcibly eject a disc

If a disc cannot be recognized by the monitor

or cannot be ejected...

The disc comes

out.

• If this does not work, reset your monitor.

• Be careful not to drop the disc when it

ejects.

Monitor

(for about 5 seconds

while power is on)

EN02-06_KV-MRD900[J]f.indd 4EN02-06_KV-MRD900[J]f.indd 4 05.3.19 11:28:23 AM05.3.19 11:28:23 AM

5

ENGLISH

DVD/VCD/JPEG special functions ... 21

Selecting audio languages ..................... 21

Selecting subtitles .................................. 21

Selecting the multi-angle views ............. 21

Disc menu operations ............................ 22

Zoom in .................................................. 22

On-Screen disc operations ............... 23

Basic on-screen bar operations .............. 24

Basic control screen operations ............. 26

List screen operations ............................ 27

DVD setup menu ............................ 28

Basic setting procedure .......................... 28

Maintenance .................................. 31

Language codes .............................. 32

More about this monitor ................. 33

Troubleshooting ............................. 37

Specifications ................................. 39

Contents

How to reset your monitor ..................... 4

How to forcibly eject a disc ................... 4

How to read this manual ........................ 4

Precautions .................................... 6

Widescreen monitor ....................... 7

Parts identification ................................. 7

Remote controller — RM-RK230

....... 8

Main elements and features ................... 8

Headphones — KS-HP2

.................... 10

Main elements and features ................... 10

Basic operations

............................. 11

Adjustments .................................. 13

Using the monitor menu ........................ 13

Changing the aspect ratio ...................... 15

Playable discs ................................ 17

Disc operations .............................. 18

Playing a disc ................................. 18

Starting playback ................................... 18

Basic operations ..................................... 19

Temperature inside the car....

If you have parked the car for a long time in

hot or cold weather, wait until the temperature

in the car becomes normal before operating the

unit.

For safety....

• Do not raise the volume level too much, as

this will block outside sounds, making driving

dangerous.

• Stop the car before performing any

complicated operations.

EN02-06_KV-MRD900[J]f.indd 5EN02-06_KV-MRD900[J]f.indd 5 05.3.19 11:28:24 AM05.3.19 11:28:24 AM

6

ENGLISH

Precautions

During the summer,

temperatures can

reach as high as

100°C (212°F).

+80°C

–20°C

–20°C to +80°C

The red spots, blue spots and green spots on

the panel surface are a normal characteristic of

liquid crystal panels, and not a problem.

Note:

The liquid crystal panel is built with very

high precision technology and has at least

99.99% effective image pixels. Be aware that

on 0.01% of the panel there may be missing or

constantly lit pixels.

When the temperature is very cold or very

hot, the image may not appear clearly or may

move slowly.

The image may not be synchronized with

the sound or the image quality may decline

in such environments. Note that this is not a

malfunction or problem.

• Usage temperature range: 0°C to +40°C

(32°F to 104°F)

0°C (32°F) or colder

40°C (104°F) or hotter

When the liquid crystal panel reaches high

temperatures or low temperatures, chemical

changes occur within the liquid crystal panel

which may cause it to malfunction.

Do not expose the liquid crystal panel to direct

sunlight.

• Storage temperature range: –20°C to +80°C

(–4°F to 176°F)

Do not drop the liquid crystal panel or strike

it sharply.

Spots

Cautions for handling the liquid crystal panel

EN02-06_KV-MRD900[J]f.indd 6EN02-06_KV-MRD900[J]f.indd 6 05.3.19 11:28:24 AM05.3.19 11:28:24 AM

7

ENGLISH

Widescreen monitor

1 (standby/on) button

• Turns on the power if pressed.

• Turns off the power if pressed and held.

2 Remote sensor

3 Dome light switch

• See “To activate the door sensor” on page

12.

4 IR transmitters

5 Dome lights

6 Arm lock lever

7 Reset button

Parts identification

8 Screen (Liquid crystal panel)

9 Disc loading slot

p 0 (eject) button

q 3 (play) button

w Disc loading lamp

e White LED

r PUSH-OPEN button

t Screen compartment

y Screen arm

When you watch the screen at an angle, the picture might not be clear. This is not a malfunction.

The finest picture can be seen when you watch the screen straight-on.

EN07-10_KV-MRD900[J]f.indd 7EN07-10_KV-MRD900[J]f.indd 7 05.3.19 11:30:49 AM05.3.19 11:30:49 AM

8

ENGLISH

Installing the lithium coin battery

(CR2025)

Before using the remote controller:

• Aim the remote controller directly at the

remote sensor on the monitor. Make sure

there is no obstacle in between.

• Do not expose the remote sensor to strong

light (direct sunlight or artificial lighting).

Warning:

• Do not install any battery other than

CR2025 or its equivalent; otherwise, it

may explode.

• Store the battery in a place where children

cannot reach to avoid risk of accident.

• To prevent the battery from over-heating,

cracking, or starting a fire:

– Do not recharge, short, disassemble, or

heat the battery or dispose of it in a fire.

– Do not leave the battery with other

metallic materials.

– Do not poke the battery with tweezers or

similar tools.

– Wrap the battery with tape and insulate

when throwing away or saving it.

Remote controller — RM-RK230

Remote sensor

Main elements and features

MONITOR CONTROL

1

(standby/on) button

• Turns on the power if pressed.

• Turns off the power if pressed and held.

2 MODE button

• Selects the playback source.

3 ASPECT button

• Changes the aspect ratio of the screen.

4 MENU button

• Calls up the menu, then selects the

adjustable menu items.

5

/ buttons

• Adjust the level of the selected item or

select an appropriate setting for selected

item.

MENU

EN07-10_KV-MRD900[J]f.indd 8EN07-10_KV-MRD900[J]f.indd 8 05.3.19 11:30:51 AM05.3.19 11:30:51 AM

9

ENGLISH

DVD/RECEIVER CONTROL

6 Receiver control buttons*

1

• (standby/on attenuator) button

• SOURCE button

• BAND button

• DUAL button

• VOL + / – (2nd VOL +/–) buttons

7 TOP M (menu) button*

2

• Displays the DVD and VCD*

3

disc menu.

8 SETUP button*

2

9 SHIFT button

p Disc basic operation buttons

7 (stop), 3 (play), 8 (pause)

• 3 (play) button functions as ZOOM

button when pressed with SHIFT button.

q Advanced disc operation buttons

•

/TITLE 5 / ∞*

4

– Select the titles (for DVD) or folders

(for MP3/WMA/JPEG)*

5

.

• 4 / ¢ (reverse skip/forward skip)*

6

• 1 / ¡ (reverse search/forward

search)*

7

w OSD button

• Displays the on-screen bar.

• Also functions as

/TITLE button when

pressed with SHIFT button.

– You can directly select folders (for

MP3/WMA/JPEG) or titles (for DVD)

using the number buttons (see right

column).

e MENU button*

2

• Displays the DVD and VCD*

3

disc menu.

r Menu operation buttons*

2

• Cursor (% , ﬁ , @ , #) and ENTER

t RETURN button*

2

y DVD/VCD special function buttons

• DVD/VCD:

(audio)

• DVD:

(subtitle), (angle)

*

1

Controllable only if your car receiver which

is connected to this monitor is one of the

JVC receivers.

*

2

These buttons function as the number

buttons when pressed with SHIFT button.

*

3

Only when PBC is not in use.

How to select a number

• To select a number from 0 – 9:

• To select a number greater than 9:

• +100/–100 buttons used only for searching

MP3/WMA/JPEG tracks number greater

than 99.

*

4

These buttons do not function as PRESET

5 / ∞.

*

5

These buttons function as the +10/–10

buttons when pressed with SHIFT button.

*

6

These buttons function as the +100/–100

buttons when pressed with SHIFT button.

*

7

Not used for MP3/WMA/JPEG operations.

EN07-10_KV-MRD900[J]f.indd 9EN07-10_KV-MRD900[J]f.indd 9 05.3.19 11:30:51 AM05.3.19 11:30:51 AM

10

ENGLISH

You can listen to the playback sounds with

cordless headphones—KS-HP2.

Installing the batteries

CAUTIONS:

• The supplied batteries are not rechargeable.

DO NOT recharge them; otherwise, battery

leakage or explosion may result.

• Insert the batteries with the correct polarity

“+” and “–” to prevent the battery leakage

or explosion.

Before using the cordless headphones:

The headphones give best results when used

within about 2 m (6.6 feet) from the transmitter.

These headphones need to receive infrared (IR)

signals sent from IR transmitters on the monitor.

Therefore, if you use the headphones where the

signals cannot be received in a straight line of

sight, noises may be generated.

Main elements and features

1 IR sensors

• DO NOT cover the IR sensors, as

reception will become poor.

2 ON/OFF button

• The power automatically shuts off in the

following cases:

– The headphones are used for about 4

hours.

– No signal is received for about 4

minutes.

• You can turn on the power again by

pressing the button.

3 POWER lamp

4 Volume control

Playback sounds are transmitted through IR

transmitters to the cordless headphones.

When using the headphones, set the monitor

menu item “IR” to “ON.” (See page 14.)

WARNING:

DO NOT use the headphones while driving.

Shutting out all outside sounds while driving

is dangerous and may result in a traffic

accident.

Headphones — KS-HP2

Left side Right side

IR transmitters

POWER

VOL

Batteries (R03/AAA)

— supplied only for

initial setup purpose

EN07-10_KV-MRD900[J]f.indd 10EN07-10_KV-MRD900[J]f.indd 10 05.3.19 11:30:53 AM05.3.19 11:30:53 AM

11

ENGLISH

Basic operations

To be continued....

Preparation

Before operating the unit, make sure that all external components are correctly connected and

installed.

1 Open the liquid crystal panel.

Press PUSH-OPEN until the liquid crystal panel is unlocked, then open the liquid crystal

panel by both hands.

CAUTION:

• When not in use, close the liquid crystal panel and store it into the compartment;

otherwise, it may obstruct the visibility through the rearview mirror.

• Do not touch the surface of the liquid crystal panel directly.

When closing the liquid crystal panel, store it in the screen compartment until it is locked.

To change the monitor position

You can select a monitor position from the four positions.

1 Slide the arm lock lever to RELEASE, then pull down or push up the monitor.

2 Slide the arm lock lever to HOLD, then remove the screen arm to the nearest locking

position.

When closing the liquid crystal panel, push up the monitor to the highest position.

EN11-16_KV-MRD900[J]f.indd 11EN11-16_KV-MRD900[J]f.indd 11 05.3.19 11:31:40 AM05.3.19 11:31:40 AM

12

ENGLISH

2 Turn on the power.

3 Select the playback source.

Each time you press the button, the playback source changes as follows:

4 Operate the playback source you selected.

To operate the built-in DVD player, see “Disc operations” on page 18.

To operate the external components, refer to the manuals for the connected components.

5 Adjust the volume on the car receiver.

• When using the headphones, adjust its volume level.

To turn off the power

• When using the headphones, turn off the power after

turning off the headphones.

To activate the door sensor

• OFF: Turns off the dome lights.

• DOOR: Activates the door sensor which turns on the dome lights when a door is open.

• ON: Turns on the dome lights.

MODE

Monitor Remote control

AV 1 AV 2DISC

EN11-16_KV-MRD900[J]f.indd 12EN11-16_KV-MRD900[J]f.indd 12 05.3.19 11:31:42 AM05.3.19 11:31:42 AM

13

ENGLISH

Using the monitor menu

You can make your own display or sound adjustments using the menu.

• For the adjustable items, see the next page.

The Remote controller—RM-RK230 has two MENU buttons.

In this section, using MENU button at MONITOR CONTROL.

Basic procedure

1

Call up the menu.

Menu selection goes off if other operations are done or no operation is done for about 5

seconds.

2 Select an item you want to adjust.

3 Adjust the level of the selected item (or select an appropriate setting for the

selected item).

4 Exit from the menu.

Press the button repeatedly until the menu is erased.

Adjustments

MENU

BRIGHT

CONTRAST

TINT

COLOR

IR ON

DIMMER

DVD SURROUND OFF

WHITE LED ON

Current menu item

Not used for changing the “DVD SURROUND” setting.

EN11-16_KV-MRD900[J]f.indd 13EN11-16_KV-MRD900[J]f.indd 13 05.3.19 11:31:42 AM05.3.19 11:31:42 AM

14

ENGLISH

Adjustable items on the monitor menu

BRIGHT:

Adjust this if the picture is too bright or too dark.

• Adjustable range: –10 to +11

• Initial level: 0 (center)

CONTRAST:

Control the degree of difference between the lightest and darkest parts

of the picture.

• Adjustable range: –10 to +11

• Initial level: 0 (center)

TINT:

Adjust this if the human skin color is unnatural.

• Adjustable range: –10 to +11

• Initial level: 0 (center)

COLOR:

Adjust the color of the picture—lighter or darker.

• Adjustable range: –10 to +11

• Initial level: 0 (center)

IR*:

Set to “ON” when you listen to the playback sounds using the cordless

headphones.

• Selectable settings: ON, OFF

• Initial setting: ON

DIMMER:

Adjust the light of the screen and the white LED when you turn on the

headlights.

• Adjustable range: –5 to +5

• Initial level: 0 (center)

DVD SURROUND:

This function allows you to get a surround effect from your stereo

system. When connecting a receiver incompatible with the multi-

channel sources, you can enjoy the virtual surround sound with your

2-channel stereo system.

If you turn off the monitor, the setting is initialized.

• Selectable settings: OFF, ACTION, DRAMA, THEATER

– ACTION: Suitable for action movies and sports programs.

– DRAMA: Creates natural and warm sound. Enjoy movies in a

relaxed mood.

– THEATER: Enjoy sound effects like in a major theater.

• Initial setting: OFF

WHITE LED:

Light on or off the white LED when you turn on the monitor.

• Selectable settings: ON, OFF

• Initial setting: ON

* Turn off the headphones before changing the “IR” setting.

EN11-16_KV-MRD900[J]f.indd 14EN11-16_KV-MRD900[J]f.indd 14 05.3.19 11:31:43 AM05.3.19 11:31:43 AM

15

ENGLISH

Changing the aspect ratio

You can select an appropriate aspect ratio for the playback video signals.

Basic procedure

Each time you press the button, aspect ratio change.

Changeable aspect ratio

When incoming 16:9 video signal:

FULL:

Pictures are fully shown on the screen.

• In some cases, the black bars may be shown at the top and

bottom sides of the screen.

NORMAL:

Pictures are reduced horizontally.

• The black bars will be shown at the left and right sides of

the screen.

• In some cases, the black bars may be shown also at the top

and bottom sides of the screen.

JUST:

The middle of pictures are reduced horizontally, and the left

and right side of the picture enlarged horizontally.

• In some cases, the black bars may be shown at the top and

bottom sides of the screen.

ZOOM:

Pictures are enlarged on the screen so that no black bars will

be shown on the screen. (The entire picture cannot be shown

on the screen.)

ASPECT

To be continued....

EN11-16_KV-MRD900[J]f.indd 15EN11-16_KV-MRD900[J]f.indd 15 05.3.19 11:31:44 AM05.3.19 11:31:44 AM

16

ENGLISH

When incoming 4:3 video signal:

FULL:

Pictures are enlarged horizontally and are fully shown on the

screen.

NORMAL:

Pictures are shown at the center of the screen.

• The black bars will be shown at the left and right sides of

the screen.

JUST:

Pictures are enlarged horizontally. The extension ratio

increases toward the both sides of the screen.

ZOOM:

Pictures are enlarged on the screen so that no black bars will

be shown on the screen. (The entire picture cannot be shown

on the screen.)

EN11-16_KV-MRD900[J]f.indd 16EN11-16_KV-MRD900[J]f.indd 16 05.3.19 11:31:44 AM05.3.19 11:31:44 AM

17

ENGLISH

Discs you can play

You can play back the following discs—12 cm

(4-3/4") and 8 cm (3-3/16")—on the built-in

DVD player:

• DVD Video: Recorded in NTSC color

system with Region Code “1” (see below).

– DVD-R/DVD-RW recorded in the DVD

Video format can also be played (see page

33).

• Video CD (VCD)/audio CD

• MP3/WMA/JPEG: Recorded either in CD-

R/CD-RW or DVD-R/DVD-RW/DVD-ROM.

– CD-R/CD-RW: Compliant with ISO 9660

Level 1, ISO 9660 Level 2, Romeo, and

Joliet.

– DVD-R/DVD-RW/DVD-ROM: Compliant

with UDF-Bridge Format*

1

.

On some discs, the actual operations may be

different from what is explained in this manual.

Discs cannot be played back

DVD-Audio, DVD-ROM (data), DVD-RAM,

DVD-R/DVD-RW recorded in the DVD-VR

format, CD-ROM, CD-I (CD-I Ready), Photo

CD, etc.

• Playing back these discs will generate noise

and damage the speakers.

Note on Region Code:

DVD players and DVD Video discs have

their own Region Code numbers. This unit

can only play back DVD discs whose Region

Code numbers include “1.”

Examples:

If you insert a DVD Video disc of an

incorrect Region Code

“REGION CODE ERROR!” appears on the

screen. The disc will eject automatically.

Playable discs

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does

not comply with the “Compact Disc Digital

Audio” standard. Therefore, the use of Non-

DVD side of a DualDisc on this product may

not be recommended.

Digital audio formats

The unit can play back the following digital

audio formats.

Linear PCM: Uncompressed digital audio,

the same format used for CDs and most studio

masters.

Dolby Digital *

2

: Compressed digital audio,

developed by Dolby Laboratories, which

enables multi-channel encode to create the

realistic surround sound.

DTS *

3

(Digital Theater Systems):

Compressed digital audio, developed by Digital

Theater Systems, Inc., which enables multi-

channel like Dolby Digital. As the compression

ratio is lower than for Dolby Digital, it provides

wider dynamic range and better separation.

MPEG Audio: Another compressed digital

audio which also enables multi-channel encode

to create the realistic surround sound. However,

this System downmix the multi-channel signals

into 2 channels (decoded PCM) and play it

back.

*

1

A hybrid file system used to provide

compatibility with ISO 9660 for accessing

any type of files on the disc. (UDF stands for

Universal Disk Format.)

*

2

Manufactured under license from Dolby

Laboratories. “Dolby” and the double-

D symbol are trademarks of Dolby

Laboratories.

*

3

“DTS” and “DTS 2.0 + Digital Out” are

trademarks of Digital Theater Systems, Inc.

“DVD Logo” is a trademark of DVD Format/

Logo Licensing Corporation registered in the

US, Japan and other countries.

EN17-30_KV-MRD900[J]f.indd 17EN17-30_KV-MRD900[J]f.indd 17 05.3.19 11:38:18 AM05.3.19 11:38:18 AM

18

ENGLISH

The disc type is automatically detected, and

playback starts automatically (for DVD:

automatic start depends on its internal program).

If the current disc is an audio CD, CD Text,

MP3/WMA, JPEG, or VCD without PBC,

all tracks will be played repeatedly until you

change the source or eject the disc.

• If a title list or disc menu appears while

playing a DVD or VCD with PBC, see “Disc

menu operations” on page 22.

The following marks are used to indicate

the playable discs....

DVD Video Video CD with PBC

Video CD

with/without PBC

Audio CD/

CD Text

MP3/WMA disc JPEG disc

All discs listed here

Before performing any operations, make

sure the following....

• For DVD playback, you can change the setup

menu setting as you like. (See pages 28 – 30.)

• For DVD/CD playback, using the remote

controller is more attractive. You can enjoy

more functions.

Starting playback

1 Open the liquid crystal panel.

• You can play a disc even if the monitor is

closed.

2 Turn on the power.

3 Insert a disc into the loading slot.

• When a disc is inserted into the loading

slot, the power comes on, then “DISC”

is selected as the playback source

automatically.

Disc operations

Playing a disc

Monitor Remote control

If “ ” appears on the monitor when

pressing a button, the disc cannot accept an

operation you have tried to do.

• In some cases, without showing “

,”

operations will not be accepted.

Playback (shining) side facing down

EN17-30_KV-MRD900[J]f.indd 18EN17-30_KV-MRD900[J]f.indd 18 05.3.19 11:38:20 AM05.3.19 11:38:20 AM

19

ENGLISH

Basic operations

Operations Next operation

To stop play temporarily

Playback pauses.

• For JPEG discs: pressing ENTER will also pause the

picture on the monitor.

A still picture appears.

A Frame by frame playback

B Slow motion playback

• No sound comes out during Slow Motion Playback.

• When playing a VCD, Reverse Slow Motion Playback is

prohibited.

To resume normal play:

To replay the previous

scenes—One Touch Replay

The playback position moves back about 10 seconds before

the current position.

• This function works only within the same title.

• For some DVDs, this function does not work.

To stop playback

When you start playback again, playback

starts from where it has been stopped

(Resume play).

When you start playback again, playback starts from

the beginning of the last playing track.

• During play, on-screen guide icons appear on the monitor for a while (see page 35).

To eject the disc

You can eject the disc even when the monitor is turned off.

To be continued....

EN17-30_KV-MRD900[J]f.indd 19EN17-30_KV-MRD900[J]f.indd 19 05.3.19 11:38:21 AM05.3.19 11:38:21 AM

20

ENGLISH

To locate a particular title/chapter/

track directly

• For DVD: During play or pause—select a

chapter.

During stop—select a title.

• For VCD: While PBC (see page 22) is not

in use.

• For MP3/WMA/JPEG: Select a track

within the same folder.

Select the number corresponding to the item

you want (see page 9).

To locate a title/folder

To the next title/folder.

To the previous title/folder.

To locate a particular title/

folder

Within 10 seconds,

press the number

buttons (see page 9).

• For MP3/WMA/JPEG discs: To directly

select the folders using the number button(s),

it is required that folders be assigned 2 digit

numbers at the beginning of their folder

names—01, 02, 03, and so on.

To go to the next or previous

chapters/tracks

• For DVD: During play or pause

To the following

chapters/tracks.

To go back to the beginning of the current

chapter/track, then the previous chapters/tracks.

To fast-forward or reverse

the chapter/track

Fast-forwards.

Reverses.

* The search speed changes to x2 ] x10 for all

discs (DVD, VCD, CD), but the information

shown on the monitor is only for DVD/VCD.

To forward or reverse

search the chapter/track

The information shown is only for DVD/VCD:

• To resume normal speed

EN17-30_KV-MRD900[J]f.indd 20EN17-30_KV-MRD900[J]f.indd 20 05.3.19 11:38:22 AM05.3.19 11:38:22 AM

La page charge ...

JVC 0305MNMMDWJEIN Manuel utilisateur

JVC 0305MNMMDWJEIN Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents