DeWalt DCN701BWRS18100 Manuel utilisateur

Marque: DeWalt

Modèle: DCN701BWRS18100

Catégorie: Cloueuse

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCN701

20V Max* Cordless Cable Stapler

Agrafeuse de câble sans fil 20V max*

Engrapadora de Cables Inalámbrica 20 V Máx*

final page size: 8.5 x 5.5 in

ENGLISH

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 15

Español (traducido de las instrucciones originales) 31

ENGLISH

English (original instructions)

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

If you have any questions or comments about this or

any

DeWALT

tool, call us toll free at:

1-800-4-

DeWALT

(1-800-433-9258).

Trigger

Utility hook

Cable alignment guide

Wire indicator

Headlight/LED work light

Magazine

Magazine release button

Pusher

Battery release button

Battery

Fig. A

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS



WARNING! Read all safety warnings,

instructions, illustrations and specs provided

with the tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

h ) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

ENGLISH

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

e ) Do not use a battery pack or tool that is

damaged or modified. Damaged or modified

batteries may exhibit unpredictable behavior resulting

in fire, explosion or risk ofinjury.

f ) Do not expose a battery pack or tool to

fire or excessive temperature. Exposure to

fire or temperature above 265 °F (129 °C) may

causeexplosion.

g ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk offire.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

Stapler Safety Warnings

• Always assume that the tool contains fasteners.

Careless handling of the stapler can result in unexpected

firing of fasteners and personalinjury.

• Do not point the tool towards yourself or anyone

nearby. Unexpected triggering could discharge a fastener

causing aninjury.

• Do not actuate the tool unless the tool is placed

firmly against the workpiece. If the tool is not in

contact with the workpiece, the fastener may be deflected

away from yourtarget.

• Disconnect the tool from the power source when the

fastener jams in the tool. While removing a jammed

fastener, the stapler may be accidentally activated if it is

pluggedin.

• When fastening electrical cables, make sure the

cables are not energized. Hold the stapler only by

insulated gripping surfaces. Use only fasteners

designed for electrical cable installations. Inspect

that the fastener has not damaged the insulation

of the electrical cables. A fastener that damages the

insulation of electric cables can lead to electric shock and

firehazards.

Additional Stapler Safety Warnings



WARNING: When using any stapler, all safety

precautions, as outlined below, should be followed

to avoid the risk of death or serious injury. Read all

instructions before operating thetool.

• Always turn off power to circuit before attempting to

staple wires. Do not staple “live”wires.

• Use only D

WALT staples for fastening electrical

cables. It is designed for electric cableinstallation.

• Never operate tool with magazine disengaged or

separated fromtool.

• Keep hands and body parts away from the discharge

area of the tool. While in use NEVER grasp the tool by the

magazine or canister, a mis-driven staple can exit the nose

causing injury.

• Always hold tool by insulated gripping surfaces

when stapling wires. Assume that they are live even

if turned off. Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock theoperator.

• Always wear appropriate personal hearing and

other protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearingloss.

• Disconnect battery pack from the tool when not in

use. Always remove battery pack and remove staples

from magazine before leaving the area or passing the

tool to another operator. Do not carry tool to another

work area in which changing location involves the use

of scaffoldings, stairs, ladders, and the like, with battery

pack connected. Do not make adjustments, perform

maintenance or clear jammed staples while battery is

inplace.

ENGLISH

• Do not remove, tamper with, or otherwise cause the

tool or trigger to become inoperable. Do not tape or

tie trigger in the on position. Do not remove spring from

wire indicator. Make daily inspections for free movement

of trigger. Uncontrolled discharge couldresult.

• Inspect tool before use. Do not operate a tool if

any portion of the tool or trigger is inoperable,

disconnected, altered, or not working properly.

Damaged parts or missing parts should be repaired or

replaced before use. Refer toRepairs.

• Do not alter or modify the tool in anyway.

• Keep bystanders, children, and visitors away while

operating a power tool. Distractions can cause you to

lose control. When tool is not in use, it should be locked in

a safe place, out of the reach ofchildren.

• Do not overreach. Maintain proper footing and

balance at all times. Loss of balance may cause

personal injury.

• Use the tool only for its intended use. Do not

discharge staples into open air or any material

too hard for the staple to penetrate. Do not use the

body of the tool or top cap as a hammer. Discharged

staple may follow unexpected path and causeinjury.

• Always keep fingers clear of wire indicator to

prevent injury from inadvertent release of thestaple.

• Refer to the Maintenance and Repairs sections for

detailed information on the proper maintenance of

thetool.

• Always operate the tool in a clean, lighted area.

Be sure the work surface is clear of any debris and be

careful not to lose footing when working in elevated

environments such asrooftops.

• Staples must be driven straight into the material. Do

not tilt the stapler while driving staples. Personal injury

can result from ricocheted or jammedstaples.

• Keep hands and body parts clear of immediate

workarea.



WARNING: To avoid injury keep hands and body

away from the front discharge area of thetool.

• Do not use tool in the presence of flammable dust,

gases or fumes. This tool produces sparks that can ignite

gases or dust causing an explosion. Driving a staple into

another staple may also cause aspark.

• Keep face and body parts away from back of the tool

cap when working in restricted areas. Sudden recoil

can result in impact to the body, especially when stapling

into hard or densematerial.

• Grip tool firmly to maintain control while allowing

tool to recoil away from work surface as staple

isdriven.

• Be aware of material thickness when using stapler. A

protruding staple may causeinjury.

• Check the wire after each shot to make sure the

cable sheathing remainsintact.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use tool while tired or under the influence of drugs,

alcohol, or medication. A moment of inattention

while operating power tools may result in serious

personalinjury.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

ENGLISH

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

.......................no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a shortcircuit.

NOTE: Lithium-ion batteries should not be put in

checked baggage.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to

ENGLISH

the FLEXVOLT™ battery, the battery is in Shipping Mode.

Strings of cells are electrically disconnected within the pack

resulting in three batteries with a lower Watt hour (Wh)

rating as compared to one battery with a higher Watt hour

rating. This increased quantity of three batteries with the

lower Watt hour rating can exempt the pack from certain

shipping regulations that are imposed upon the higher Watt

hourbatteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

For example, Shipping Wh rating might indicate 3 x 40 Wh,

meaning 3 batteries of 40 Watt hours each. The Use Wh

rating might indicate 120 Wh (1 batteryimplied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

Fig. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

ENGLISH

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center forrecycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting batterypack.

Fig. C

2. Insert the battery pack

10

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

9

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before

firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

DCB101

Charging

Fully Charged

Hot/Cold Pack Delay

Problem Pack or Charger

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

ENGLISH

yellow light will turn off and the charger will resume the

chargingprocedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized servicecenter.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB115 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to becooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of thecharger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deepdischarge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fullycharged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaningsolutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack below +40°F (+4.5°C), or above

+104°F (+40°C). This is important and will prevent

serious damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the batterypack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting toclean.

6. Do not freeze or immerse the charger in water or any

otherliquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat orcold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged beforeuse.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

ENGLISH

Intended Use

Your cable stapler is intended ONLY for use in driving

staples into wood.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

Use ONLY

DeWALT

staples that meet applicable building

coderequirements.

This tool is intended for use by construction professionals.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

TOOL SPECIFICATIONS

Actuation mode Sequential

Voltage 20V

Height 7.5" (190.5 mm)

Width 2.875" (73 mm)

Length 12" (304.8 mm)

Weight 4.75 lbs (2.15 kg) without battery

5.6 lbs (2.54 kg) with DCB203 battery

Magazine angle 0˚ straight

Loading capacity Up to 35 staples

Dry fire lock-out Yes

LED Yes

STAPLE SPECIFICATIONS

Staple type DRS18100 Insulated cable staple

Staple lengths 1" (25.3 mm)

Staple crown 3/4" (19.7 mm)

Staple insulator 0.85" (21.6 mm) long x 0.16" (4 mm) wide

Dry Fire Lock Out

Your stapler is equipped with a dry fire lockout which

prevents the tool from actuating when the magazine

is empty. After the last staple is fired the tool ceases to

operate. Refer to Loading the Tool to reload a stick of

collatedstaples.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery

pack before loading staples, making any

adjustments or removing/installing attachments

or accessories. An accidental actuation can

causeinjury.



WARNING: Remove staples from magazine before

making any adjustments or servicing this tool. Failure

to do so may result in serious injury.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping or

falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be

easily knocked over.

Utility Hook (Fig. D)

The

DeWALT

cordless stapler includes an integrated utility

hook

2

and can be installed on either side of the tool to

accommodate left- or right-handedusers.

If the hook is not desired at all, it can be removed from

thetool.

To Install the Utility Hook

1. Remove staples and battery pack fromtool.

2. Using only the provided screw

, the utility hook

2

can be be installed on either side of the tool. To

switch the tool from right- or left-hand usage simply

remove the screw and install the utility hook on the

oppositeside.

3. Load staples and replace battery pack .

Fig. D

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery

pack before loading staples, making any

adjustments or removing/installing attachments

or accessories. An accidental actuation can

causeinjury.



WARNING: Read the section titled Stapler Safety

Warnings at the beginning of this manual. Always

wear eye and ear protection when operating this

tool. Keep the stapler pointed away from yourself and

others. For safe operation, complete the following

procedures and checks before each use of thestapler.



WARNING: To reduce the risk of personal injury,

disconnect battery pack from tool before performing

maintenance, clearing a jammed staple, leaving work

area, moving tool to another location or handing the

tool to anotherperson.



WARNING: NEVER use a tool that has the wire

indicator restrained in the upposition.



WARNING: NEVER use a tool that has

damagedparts.

Installing and Removing the Battery Pack

(Fig. E)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack

10

into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

ENGLISH

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button

9

and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

Fig. E

Proper Hand Position (Fig. F)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the handle

as shown in Fig. F.

Fig. F

Preparing the Tool (Fig. A)

NOTICE: NEVER spray or in

any other way apply lubricants

or cleaning solvents inside the

tool. This can seriously affect

the life and performance of

thetool.

NOTE: The battery pack is not fully charged out of the

carton. Follow instructions outlined (refer to Charging

ABattery).

1. Read the Stapler Safety Warnings section of

thismanual.

2. Wear eye and earprotection.

3. Remove battery

fromtool.

4. Ensure magazine

is empty of allfastners.

5. Check for smooth and proper operation of cable

alignment guide

3

, wire indicator

and pusher

assemblies. Do not use tool if either assembly is not

functioning properly. NEVER use a tool that has the wire

indicator restrained in the actuatedposition.

6. Keep tool pointed away from yourself andothers.

NOTICE: Do not store tool with battery pack installed.

To prevent damage to the pack and to ensure best

battery life, store battery packs out of the tool or

charger in a cool, drylocation.

Loading the Tool (Fig. G)



WARNING: Keep the tool pointed away from yourself

andothers.



WARNING: Never load staples with the wire indicator

or triggeractivated.



WARNING: Always remove battery pack before

loading or unloadingstaples.



CAUTION: Keep fingers clear of pusher latch track to

preventinjury.



WARNING: Use

DeWALT

staples only in this tool.

Other staples can damage the wire insulation. Which

may result in electric shock, fire and/or seriousinjury.

1. Depress magazine release button

and slide the

magazine core and pusher

out until it reaches the

end of itstravel.

2. Drop staple strips into the loading slot of the

magazine

6

, making sure the staple heads align

correctly with the slot opening. (Refer to Staple

Specifications to determine compatible size.)

Fig. G

3. Keeping fingers clear of the track, close the magazine by

releasing the pusher latch. Carefully allow the latch to

slide forward and engage the staplestrip.

NOTE: Do not slam magazine core assembly into

magazine or you could damagestaples.

Unloading the Tool



WARNING: Always remove battery pack before

loading or unloadingstaples.

1. Depress magazine release button

and slide the

magazine core and pusher

out until it reaches the

end of itstravel.

ENGLISH

Fig. I



WARNING: Staples must be driven straight into the

material. Do not tilt stapler while driving staples. Refer

to Figure J. Staple retention values improve when tool

is fired perpendicular to thematerial.

Fig. J

4. Push tool against cable firmly to depress cable

alignment guide

all the way as well as wire

indicator

4

, pull trigger

and a staple will befired.

5. Check wire for damage after eachshot.

NOTE: When firing into certain materials such as LVL or TJI

joist, you may need to apply additional force toward the

workpiece to properly seat thestaple.



WARNING: Use caution in locating stapler over cable

or wire to prevent the staple from piercing the cable

jacket or insulation. After firing each staple, visually

inspect driven staple to make sure wire insulation was

not damaged. If damaged replacewire.

The DRS18100 insulated cable staples are UL® approved for

the following combinations of Romex®wiring.

2. Tip the tool right side up until the staple strips fall freely

out of themagazine.

3. Close the magazine by sliding the magazine core back

into the magazine fully until it latches. Do not slam

magazine core into themagazine.

Headlight/LED Worklight (Fig. H)

There is a headlight/LED worklight

located at the front

of the unit. The headlight turns on upon battery insertion,

activation of the trigger, or depressing the wire indicator.

The light will automatically shut off after 20seconds unless

tool remains inuse.

NOTE: The headlight is for lighting the immediate work

surface and is not intended to be used as aflashlight.

Fig. H

LOW BATTERY INDICATOR: The headlight will flash

four consecutive times and then shut down to indicate

lowbattery.

Actuating the Tool (Fig. I, J)



WARNING: Always turn off power to circuit before

attempting to staple wires. Do not staple “live”wires.



WARNING: Always assume that the tool contains

staples. Careless handling of the stapler can result in

unexpected firing of staples and personal injury. Do

not point the tool towards yourself or anyone nearby.

Unexpected triggering could discharge a staple

causing an injury. No horseplay! Work Safe! Respect

the tool as a workingimplement.



WARNING: Do not actuate the tool unless the tool

is placed firmly against the workpiece. If the tool is

not in contact with the workpiece, the staple may be

deflected away from yourtarget.

There is no need for depthadjustment.

1. Load unit withstaples.

2. Place battery intotool.

3. Locate cable alignment guide

directly over the cable

or wire you wish to staple so that the wire is centered

as much as possible between the 2 prongs of the cable

alignmentguide.

ENGLISH

UL® Approved Romex® Cable

Combinations

(NM Sheathed Cable)

Cable Gauge Single Cable Double Stacked Cable

14-2 X X

Any Combination:

14-2 or 14-3 or 12-2

or 12-3 or 10-2

14-3 X X

12-2 X X

12-3 X X

10-2 X X

10-3 X

Clearing a Jammed Staple (Fig. A)



WARNING: To reduce the risk of serious personal

injury, disconnect battery pack from tool before

making any adjustments, changing accessories,

servicing, or moving the tool. Such preventative safety

measures reduce the risk of firing the tool accidentally.

1. Remove battery pack

fromtool.

2. Depress magazine release button

and slide the

magazine core and pusher

out until it reaches the

end of itstravel.

3. Tip the tool right side up until any loose staple strips

fall freely out of the magazine. Any jammed staples can

then beremoved.

4. Refill magazine with newstaples.

Cold Weather Operation

When operating tools at temperatures below freezing:

1. Keep tool as warm as possible prior touse.

2. Actuate the tool a few times into scrap lumber over a

piece of scrap cable beforeusing.

Hot Weather Operation

Tool should operate normally. However, keep tool out of

direct sunlight as excessive heat can deteriorate bumpers

and other rubber parts resulting in increasedmaintenance.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery

pack before loading staples, making any

adjustments or removing/installing attachments

or accessories. An accidental actuation can

causeinjury.

DAILY MAINTENANCE CHART

ACTION Clean magazine, pusher, and wire

indicatormechanism.

WHY Permits smooth operation of magazine,

reduces wear, and preventsjams.

HOW Blowing off the tool with compressed air is

the most effective way to clean the tool. The

use of oils, lubricants periodically or solvents

is not recommended as they tend to attract

debris and/or damage the plastic parts of

thetool.

ACTION Before each use, check to ensure all screws

and staples are tight andundamaged.

WHY Prevents jams and premature failure of

toolparts.

HOW Tighten loose screws using the appropriate

hex wrench orscrewdriver.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: NEVER use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Lubrication

NOTICE: NEVER spray or

in any other way apply

lubricants or cleaning

solvents inside the tool.

This can seriously affect

the life and performance of

thetool.

DeWALT

tools are properly lubricated at the factory and are

ready for use. However, it is recommended that, once a year,

you take or send the tool to a certified service center for a

thorough cleaning andinspection.

Accessories



WARNING: Since accessories, other than those

offered by

DeWALT

, have not been tested with this

product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used with

thisproduct.

Recommended accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact

DeWALT

Industrial Tool Co., 701

ENGLISH

East Joppa Road, Towson, MD 21286, call 1–800–4-

DeWALT

(1–800–433–9258) or visit our website www.

DeWALT

.com.

Repairs

There are no user serviceable parts inside thestapler.

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement) should

be performed by a

DeWALT

factory service center

or a

DeWALT

authorized service center. Always use

identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from

the date of purchase. This warranty does not cover

part failure due to normal wear or tool abuse. For

further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-

DeWALT

(1-800-433-9258). This warranty does not apply to

accessories or damage caused where repairs have been

made or attempted by others. THIS LIMITED WARRANTY

IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states do not allow

limitations on how long an implied warranty lasts or the

exclusion or limitation of incidental or consequential

damages, so these limitations may not apply to you. This

warranty gives you specific legal rights and you may have

other rights which vary in certain states orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase. ADD WEAR STATEMENT: NO SPRINGS

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB203, DCB204, DCB204BT, DCB205, DCB205BT,

DCB206, DCB230, DCB606, DCB609, DCB612

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Stapler for any reason,

you can return it within 90 days from the date of purchase

with a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

ENGLISH

TROUBLESHOOTING GUIDE

Many common problems can be solved easily by utilizing the chart below. For more serious or persistent problems,

contact a

DeWALT

service center or call 1-(800)-4-

DeWALT



WARNING: To reduce the risk of serious personal injury, ALWAYS disconnect battery pack from tool before

allrepairs.

SYMPTOM CAUSE FIX

Tool will not fire Dryfire lock out engaged, blocking wire

indicator from traveling fully.

Load more staples into magazine.

Battery is hot. Let the battery cool or replace it with a cool pack.

Tool is hot. Let the tool cool down before continuing use.

Bent contact trip. See authorized service center.

Terminals are dirty or damaged. See authorized service center.

Damaged internal electronics. See authorized service center.

Damaged trigger. See authorized service center.

Jammed staple/drive blade not returned

to home position.

Remove battery, clear jammed staple, reinsert battery pack, driver blade

will reset by using the tool normally (first cycle will not fire a staple).

Damaged driver. See authorized service center.

Jammed internal mechanism. See authorized service center.

Damaged internal electronics. See authorized service center.

Tool operates but does not drive

fasteners fully

Tool not firmly applied to workpiece. Apply adequate force to tool securing it tightly to workpiece. Refer to

Actuating the Tool.

Damaged or worn driver tip. See authorized service center.

Damaged actuation mechanism. See authorized service center.

Tool operates, but no fastener

is driven

Wrong size or staples. Use only the recommended staples. Refer to Staple Specifications.

Debris in nosepiece. Clean nose area and watch closely for small pieces of broken staples stuck

in the track.

Debris in magazine. Clean magazine.

Damaged pusher spring. Replace spring. See authorized service center.

Worn magazine. Replace magazine. See authorized service center.

Jammed staples Wrong size or staples. Use only the recommended staples. Refer to Staple Specifications.

Magazine not secured after previous jam

clear/inspection.

Make sure the magazine is latched properly.

Material and fastener length. If the unit continues to stall, see authorized service center.

Debris in nosepiece. Clean nose area and watch closely for small pieces of broken staples stuck

in the track.

Worn magazine. Replace magazine. See authorized service center.

Damaged pusher spring. Replace springs. See authorized service center.

Damaged or worn driver. Replace driver with kit.

Staples do not fit Confirm D

WALT staples are being used. Your stapler is only compatable with D

WALT staples.

FRANÇAIS

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Pour toute question ou remarque au sujet de cet outil

ou de tout autre outil

DeWALT

, composez le numéro

sans frais : 1-800-4-

DeWALT

(1-800-433-9258).

Gâchette

Crochet utilitaire

Guide d’alignement du

câble

Indicateur du câble

Lumière/Lampe de

travail DEL

Magasin

Bouton de libération du

magasin

Poussoir

Bouton de libération du

bloc-piles

Bloc-piles

Français (traduction de la notice d’instructions originale)

Fig. A

FRANÇAIS

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

POUR LES OUTILS ÉLECTRIQUES



AVERTISSEMENT! lisez tous les avertissements de

sécurité, toutes les instructions, les illustrations

et les caractéristiques fournis avec cet outil

électrique. Le non-respect des avertissements et des

directives pourrait se solder par un choc électrique, un

incendie et/ou une blessuregrave.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sansfil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise à

l’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre corps

est mis à laterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive.

Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

h ) Ne pas laisser votre connaissance acquise suite

l’utilisation fréquente des outils vous permettre

de baisser la garde et ignorer les principes de

sécurité de l’outil. Un acte irréfléchi peut causer une

blessure grave en une fraction deseconde.

FRANÇAIS

4) Utilisation et entretien d’un outil

électrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et

doit êtreréparé.

c ) Débrancher la fiche de la source d’alimentation

et/ou du bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire

ou avant de ranger l’outil. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

e ) Entretien des outils électriques. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus

faciles àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les

forets, etc. conformément aux présentes

directives en tenant compte des conditions de

travail et du travail à effectuer. L’utilisation d’un

outil électrique pour toute opération autre que celle

pour laquelle il a été conçu estdangereuse.

h ) Garder vos mains et les surfaces de prise sèches,

propres et libres de graisse et de poussière. Les

mains et les surfaces de prise glissante ne permettent

pas la manutention et le contrôle sécuritaires de l’outil

dans les situationsimprévues.

5) Utilisation et entretien du bloc-piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc-piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc-piles.

b ) Utiliser les outils électriques uniquement avec

les blocs-piles conçus à cet effet. L’utilisation de

tout autre bloc-piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc-piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court-circuit des bornes du bloc-piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc-piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc-piles peut provoquer

des irritations ou desbrûlures.

e ) Ne pas utiliser de bloc-piles ou outil qui

a été endommagé ou modifié. Les unités

endommagées ou modifiées peuvent avoir une

réaction imprévisible résultant en un incendie,

une explosion ou un potentiel de blessure.

f ) Ne pas exposer de bloc-piles ou l’outil aux

flammes ou à des températures excessives.

L’exposition aux flammes ou à une température

au-dessus de 129°C (265°F) pourrait causer

uneexplosion.

g ) Suivre toutes les instructions de recharge et

ne rechargez pas le bloc-piles ou l’outil à des

températures hors de la plage de température

indiquée dans les instructions. Une recharge non

conforme ou à une température hors des limites

spécifiées peut endommager les piles et augmenter le

risque d’incendie.

6) Réparation

a ) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de

rechange identiques. Cela permettra de maintenir

une utilisation sécuritaire de l’outilélectrique.

b ) Ne jamais réparer des blocs-piles endommagés.

La réparation de blocs-piles doit seulement être

effectuée par le fabricant ou les fournisseurs de

serviceautorisé.

Avertissements de sécurité concernant

l’agrafeuse

• Tenez toujours pour acquis que l’outil contient des

agrafes. Une manipulation imprudente de l'agrafeuse

peut entraîner un tir inattendu d’agrafes et une

blessurecorporelle.

• Ne pas pointer l’outil vers vous ou toute personne

à proximité. Un déclenchement inattendu pourrait

décharger une agrafe causant uneblessure.

• Ne pas actionner l’outil à moins que l’outil soit

fermement placé contre la pièce de travail. Si l’outil

n’est pas en contact avec la pièce de travail, l’attache peut

être déviée de votrecible.

• Débranchez l’outil de la source d’alimentation

lorsque la fixation bloque dans l’outil. Lorsque

FRANÇAIS

vous retirez une fixation bloquée, l’agrafeuse peut être

accidentellement activée si elle estbranchée.

• Lorsque vous fixez des câbles électriques, assurez-

vous que les câbles ne sont pas sous tension. Tenez

l’agrafeuse seulement par les surfaces de prise

isolées. Utilisez seulement des fixations conçues

pour des installations de câbles électriques. Vérifiez

si la fixation n’a pas endommagé l’isolation des

câbles électriques. Une fixation qui endommage

l’isolation des câbles électriques peut entraîner des risques

de chocs électriques et d’incendie.

Avertissements de sécurité

supplémentaires concernant l’agrafeuse



AVERTISSEMENT: lorsque vous utilisez une

agrafeuse, toutes les consignes de sécurité, selon les

modalités suivantes, doivent être suivies afin d’éviter

le risque de mort ou de blessure grave. Lisez toutes les

instructions avant d’utiliser l’outil.

• Coupez toujours le courant avant de tenter d’agrafer

des câbles. Ne pas agrafer des câbles soustension.

• Utilisez des agrafes D

WALT pour fixer des câbles

électriques. Elles sont conçues pour l’installation de

câblesélectriques.

• Ne jamais utiliser l’outil si le magasin n’est pas

enclenché ou s’il est séparé de l’outil.

• Gardez les mains et les parties de votre corps

à l’écart de la zone de sortie de l’outil. Pendant

l’utilisation, NE JAMAIS prendre l’outil par le magasin ou

la cartouche, une fixation mal enfoncée peut sortir du nez

causant une blessure.

• Tenez toujours l’outil par les surfaces de prise isolées

lorsque vous fixez des câbles. Tenez pour acquis

que l’outil sous tension même s’il est éteint. Entrer en

contact avec un câble «sous tension» exposera aussi les

pièces métalliques de l’outil «sous tension» et pourrait

donner un choc électrique à l’utilisateur.

• Toujours porter une protection auditive et toute

autre protection convenable lors de l’utilisation

de l’outil. Dans certaines conditions et selon la durée

d’utilisation, le bruit émis par ce produit pourrait

contribuer à une perteauditive.

• Débranchez le bloc-piles de l’outil lorsqu’il n’est pas

utilisé. Retirez toujours le bloc-piles et retirez les agrafes

du magasin avant de quitter l’aire ou de passer l’outil à

un autre utilisateur. Ne pas transporter l’outil dans une

autre aire de travail dans laquelle changer de localisation

implique l’utilisation d’échafaudages, d’escaliers, d’échelles

et d’autres objets semblables, avec le bloc-piles branché.

Ne pas faire d’ajustements, faire un entretien ou retirer des

agrafes obstruées pendant que la pile est enplace.

• Ne pas retirer, modifier ou rendre l’outil ou la

gâchette inutilisable. Ne pas coller la gâchette avec

du ruban ou l’attacher en position Marche. Ne pas retirer

le ressort de l’indicateur du câble. Faites des inspections

quotidiennes pour le libre mouvement de la gâchette. Cela

pourrait causer une décharge noncontrôlée.

• Inspectez l’outil avant de l’utiliser. Ne pas utiliser

l’outil si une partie de l’outil ou de la gâchette est

inutilisable, déconnectée, altérée ou ne fonctionne

pas bien. Les pièces endommagées ou manquantes

doivent être réparées ou remplacées avant l’utilisation.

ConsultezRéparations.

• Ne jamais altérer ou modifier l’outil.

• Gardez les passants, les enfants et les visiteurs

éloignés lorsque vous utilisez un outil électrique. Les

distractions peuvent vous faire perdre le contrôle. Lorsque

l’outil n’est pas utilisé, il doit être verrouillé dans un endroit

sécuritaire, hors de portée desenfants.

• Ne pas trop vous étirer. Maintenez vos pieds bien

d’aplomb sur le sol et un bon équilibre en tout

temps. La perte d’équilibre pourrait causer des blessures.

• Utilisez l’outil seulement pour son utilisation prévue.

Ne pas décharger les agrafes à l’air libre ou dans

tout matériau trop dur pour que l’agrafe y pénètre.

Ne pas utiliser le corps de l’outil ou le capuchon

supérieur comme marteau. Les agrafes déchargées

peuvent suivre une trajectoire inattendue et causer

uneblessure.

• Gardez toujours les doigts à l’écart de l’indicateur

du câble afin de prévenir une blessure due à la

libération accidentelle de l’agrafe.

• Consultez les sections Entretien et Réparations

pour des renseignements détaillés sur l’entretien

approprié de l’outil.

• Utilisez toujours l’outil dans un endroit propre et

éclairé. Assurez-vous que la surface de travail est libre de

tout débris et faites attention à ne pas perdre pied lorsque

vous travaillez dans des environnements élevés comme

lestoits.

• Les agrafes doivent être enfoncées droites dans le

matériau. Ne pas incliner l’agrafeuse pendant que vous

enfoncez les agrafes. Le ricochet ou le blocage d’agrafes

peut entraîner une blessurecorporelle.

• Gardez vos mains et les autres parties de votre corps

à l’écart de l’aire de travailimmédiate.



AVERTISSEMENT: pour éviter blessure corporelle,

gardez vos mains et votre corps à l’écart de la zone de

sortie de l’outil.

• Ne pas utiliser l’outil en présence de poussière, de

gaz et de vapeurs inflammables. Cet outil produit des

étincelles qui peuvent enflammer les gaz ou la poussière

causant une explosion. Enfoncer une agrafe dans une

autre agrafe peut aussi causer uneétincelle.

• Gardez votre visage et les parties de votre corps à

l’écart de l’arrière du capuchon de l’outil lorsque

vous travaillez dans des aires restreintes. Un

recul soudain peut entraîner un impact avec le corps,

particulièrement lorsque vous brochez dans un matériau

dur oudense.

• Saisissez fermement l’outil pour maintenir le

contrôle tout en laissant l’outil reculer de la surface

de travail une fois l’agrafeenfoncée.

La page charge ...

DeWalt DCN701BWRS18100 Manuel utilisateur

Marque: DeWalt

Modèle: DCN701BWRS18100

Catégorie: Cloueuse

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCN701BWRS18100 User manual
español: DeWalt DCN701BWRS18100 Manual de usuario

DeWalt DCN701BWRS18100 Manuel utilisateur

DeWalt DCN701BWRS18100 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents