Craftsman CMXWDCR01137 Manuel utilisateur

Marque: Craftsman

Modèle: CMXWDCR01137

Catégorie: Stations météo

Taper: Manuel utilisateur

Vous trouverez ci-dessous de brèves informations pour Thermomètre sans fil 00609A2TX, Thermomètre sans fil CMXWDRC01137-TX, Thermomètre sans fil CMXWDRC01134-TX, Thermomètre sans fil CMXWDCR01137. Ce thermomètre sans fil CRAFTSMAN fournit des lectures précises et fiables de la température et de l'humidité, ainsi que l'heure et la date. L'écran LCD affiche la température et l'humidité actuelles intérieures/extérieures avec des flèches d'indication de tendance et des informations quotidiennes sur les températures hautes/basses. L'écran intérieur peut être posé sur une table ou fixé au mur. Le capteur extérieur sans fil a une puissante technologie sans fil et une conception résistante aux intempéries.

WIRELESS

THERMOMETER

CMXWDCR01137

INSTRUCTION MANUAL

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

1-888-331-4569 WWW.CRAFTSMAN.COM

Tower Sener Model:

00609A2TX

CMXWDRC01137-TX

CMXWDRC01134-TX

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.

English (original instructions)

LangRef_U_NA_U_U-ENG

WARNING: GENERAL SAFETY

• Do not immerse device in water. This can cause electrical shock and damage the product.

• Do not disassemble device or tamper with internal components. Damage caused by disassembly is not covered

by the warranty. No user-serviceable parts are inside these devices.

• Avoid dropping device; this may damage internal components.

• Keep all parts and batteries out of the reach of children.

• Use care when mounting the Wireless Outdoor Sensor out of arm's reach. When using a ladder to mount, it must

be secure to avoid falls that may result in personal injury or property damage.

• Do not mount Wireless Outdoor Sensor near overhead power lines or other unsafe hanging areas.

WARNING: BATTERY SAFETY AND DISPOSAL BATTERY SAFETY

Read all safety warnings and all instructions before operating devices.

Compare the illustrations with the devices to familiarize yourself with the supplied components and setup instructions.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

WARNING: MAINTENANCE AND CARE

• Clean devices with a soft, damp cloth. Do not use caustic cleaners or abrasives.

• Keep Indoor Display away from dust, dirt, and moisture. Clean ventilation ports regularly with a gentle puff of air.

• Replace device batteries when low battery icon is shown. Follow all battery recommendations, disposal, and safety

information detailed in this guide.

• Wireless Outdoor Sensor is water-resistant and designed for general outdoor use. To extend its life, place in an area

protected from direct weather elements, including rain, snow, and frost.

BATTERY SAFETY

Clean the battery contacts and also those of the device prior

to battery installation. Remove batteries from device which

is not to be used for an extended period of time. Replace all

batteries of a set at the same time. Only batteries of the same

or equivalent type as recommended are to be used. Ensure

the batteries are installed with correct polarity (+ and -).

Promptly remove dead or expired batteries.



CAUTION: DO NOT mix old and new batteries or

batteries of different types. DO NOT use rechargeable

batteries. DO NOT recharge non-rechargeable

batteries. DO NOT short-circuit the supply terminals.

BATTERY DISPOSAL

Dispose of old or defective batteries in an environmentally

safe way and in accordance with your local laws

and regulations.

WARNING: DO NOT incinerate used batteries.

DO NOT dispose of batteries in fire, because they

could explode or leak.

KNOW YOUR WIRELESS THERMOMETER

Weather the day with confidence with your own accurate and up-to-date information – right from your own backyard.

The CRAFTSMAN Wireless Thermometer features precise, reliable temperature and humidity readings, along with the time

and date. The bold, easy to read LCD screen displays the current indoor / outdoor temperature and humidity with trend

indicator arrows and daily high / low information. The Indoor Display stands upright for tabletop use or is wall-mountable.

The Wireless Outdoor Sensor features powerful wireless technology, a weather-resistant design and an integrated hanger

for easy mounting.

INDOOR DISPLAY FEATURES

1 Outdoor Conditions

• Current temperature (°F or °C)

• Current humidity level (%)

• Trending arrows indicate if the condition is

trending up or down

• Wireless Outdoor Sensor signal strength

• Wireless Outdoor Sensor low battery icon

indicates when batteries need to be changed

2 Indoor Display Information

• Current time and date

• Low battery indicator indicates when

batteries need to be changed

3 Indoor Conditions

• Current temperature (°F or °C)

• Current humidity level (%)

• Trending arrows indicate if the condition is

trending up or down

4 Display Buttons

• MIN/MAX buttons: view today's low and high

temperature and humidity records

• SETUP and buttons: set time, date, and

temperature units to Fahrenheit or Celsius

5 Battery compartment

• Requires three AAA batteries (not included)

6 Tabletop stand

WIRELESS OUTDOOR SENSOR FEATURES

1 Mounting Hanger

2 Wireless Signal Indicator

• Flashes when sending data to the Indoor

Display

3 Battery Compartment

• Requires two AA batteries (not included)

HOW TO SET UP YOUR WIRELESS THERMOMETER

What You'll Need (Not Included)

• Two AA batteries for the Wireless Outdoor Sensor

Be sure to use high-quality alkaline batteries. Heavy duty or rechargeable batteries are not recommended. Only use

Lithium batteries when the outdoor temperature is below -4ºF/-20ºC for extended periods of time. In general, alkaline

batteries perform poorly in very cold weather.

• Three AAA batteries for the Indoor Display

Be sure to use high-quality alkaline batteries. Lithium, heavy duty, and rechargeable batteries are not recommended.

STEP 1

Insert Wireless Outdoor Sensor Batteries

STEP 3

Set Indoor Display Time, Date, and Temperature Units to Fahrenheit or Celsius

a. Press and hold the SETUP button. When in setup mode, the selected setting flashes on the Indoor Display.

• To adjust a setting, press and release the or button. To save a setting, press and release the SETUP button.

The next setting is selected.

• Settings are displayed in the following order:

• Auto DST ON/OFF. When set to ON, time will update for Daylight Saving Time.

If your location does not observe DST, set it to OFF.

• CLOCK HOUR

• CLOCK MINUTE

• CALENDAR MONTH

• CALENDAR DATE

• CALENDAR YEAR

• TEMPERATURE UNITS (ºF or ºC)

b. To exit from setting mode, do not press a button for 8 seconds. The Indoor Display returns to its normal

operating mode.

STEP 2

Insert Indoor Display Batteries

WIRELESS THERMOMETER

CMXWDCR01137

Where to Place the

Wireless Outdoor Sensor

• In a well-shaded area, away from direct sunlight

When placed in direct sunlight, the heat from the sun

may cause the temperature readings to be higher than

the actual ambient air temperature. The best location is

commonly on the north side of your home.

• 4 to 8 feet (1. 2 to 2.4 meters) above the ground

Too low and it will pick up excess heat from the ground.

Too high and it will cool from the wind.

• In an area that has good airflow

This keeps the air circulating freely around the sensor. If

placed too close to a solid object, the readings may not

be accurate.

• Above a natural (grassy or dirt) surface

Concrete, pavement, and stone absorb heat and will

impact readings.

• Protected from direct weather elements

The sensor is water-resistant and for general outdoor

use. Weather elements, such as rain or snow, or a damp

or excessively humid area, may damage the device.

How to Mount the

Wireless Outdoor Sensor

• Using the mounting hanger: attach a string (not

included) to its mounting hanger and secure string

to a solid object, such as a tree branch.

STEP 4

Place Indoor Display And Wireless Outdoor Sensor

Both devices are sensitive to their surrounding environment and location. Proper placement is required for accurate

readings and wireless communication.

Important Location Guidelines For Wireless Communication

The following guidelines are very important to ensure both devices have signal strength to connect wirelessly.

• Locate within 165 feet (50 meters) of each other

If located farther away, the devices may have trouble connecting.

• Away from large solid objects

Thick walls, metal surfaces, concrete, or other objects may limit wireless communication.

• At least 3 feet (0.9 meters) away from electronic devices

Televisions, computers, microwaves, radios, and other electronic devices may cause wireless interference.

3 feet

(.9 m)

165 feet maximum (50 meters)

STEP 5

Verify Wireless Connection and Signal Strength

• Verify the Indoor Display shows the Outdoor Conditions

• After placing the Wireless Outdoor Sensor, it may take up to five (5) minutes to display the Outdoor Conditions.

• Verify the Wireless Outdoor Sensor red LED flashes every 30 seconds, which indicates readings are being

sent to the Indoor Display.

• From the Indoor Display, verify the Wireless Outdoor Sensor signal strength.

SIGNAL ICON SIGNAL STRENGTH WHAT IT INDICATES

Excellent

Indoor Display can receive the Outdoor Conditions.

Good

Fair May result in loss of connection or the Outdoor Conditions may not be accurate.

Refer to Troubleshooting section in this guide for more information.

No Signal

(flashing)

Indoor Display cannot receive the Outdoor Conditions.

Outdoor Conditions may be flashing or showing dashes (---) or may not be accurate.

Refer to Troubleshooting section in this guide for more information.

Temperature range Indoor temperature: 32º to 122º F / 0º to 50º C

Outdoor temperature: -40º to 158º F / -40º to 70º C

Humidity range 1% to 99% Relative Humidity (RH)

Wireless communication 433 MHz wireless radio frequency (RF)

Wireless signal range Up to 165 feet (50 meters)

Power Indoor Display: three AAA alkaline batteries

Wireless Outdoor Sensor: two AA alkaline or lithium batteries

Display update interval Indoor conditions: every 60 seconds

Outdoor conditions: every 30 seconds

SPECIFICATIONS

Where to Place the Indoor Display

Be sure to remove the protective film from its LCD screen, locate the tab and peel off the film.

• Place on a flat surface or mount to a solid wall surface in dry area free of dirt and dust

• Keep out of direct sunlight

• Keep away from heat sources

PROBLEM CAUSE CORRECTION

No bars shown No wireless connection

between devices

Verify device locations and low battery indicator:

• Verify the devices are within 165 feet (50 meters) of each other. You may need to

relocate the Indoor Display or Wireless Outdoor Sensor to get a better signal strength.

• Verify both devices are located 3 feet (0.9 meters) away from electronics that may

interfere with their wireless signal, such as televisions, microwaves, or computers.

• If a low battery indicator is shown, replace the device batteries. Be sure to

use high-quality alkaline batteries. Heavy duty or rechargeable batteries are not

recommended. Only use Lithium batteries in the Wireless Outdoor Sensor when the

outdoor temperature is below -4ºF/-20ºC for extended periods of time.

When batteries are replaced, it may take up to five (5) minutes for the devices to

establish a wireless connection. When connected, the Indoor Display will show the

Outdoor Conditions.

Outdoor Conditions

readings are flashing or

showing dashes (---)

Wireless interference or

loss of signal

Reset devices' wireless connection:

1. Bring the Wireless Outdoor Sensor indoors and place it within 2 feet (0.6 meters) from

the Indoor Display.

2. Remove one battery from both devices.

3. Reinsert the Wireless Outdoor Sensor battery.

4. Reinsert the Indoor Display battery. The display searches for and wirelessly connects to

the Wireless Outdoor Sensor.

5. Let the devices sit within a couple of feet of each other for approximately five (5)

minutes to establish a strong wireless connection.

Inaccurate temperature Device location

affecting its readings

Verify both devices are not located:

• In direct sunlight.

• Near heat sources such as vents, stoves, or other elements that emit heat.

• On or near a window or other uninsulated surface, such as a brick wall, that can get

much warmer or cooler.

• In a confined location where the air may not circulate enough.

Indoor Display is blank No battery power Verify batteries are installed correctly. You may need to replace the batteries.

Note

When the Indoor Display batteries are replaced or after a loss of battery power, you

will need to reset its time, date, and temperature units.

When batteries are replaced or after a loss of battery power, it may take up to

five (5) minutes for the devices to reestablish their wireless connection. When

connected, the Indoor Display will show the Outdoor Conditions and the Wireless

Outdoor Sensor red LED

TROUBLESHOOTING REGISTER ONLINE

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a

problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of

ownership will serve as your proof ofpurchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is

required under the Federal Consumer SafetyAct.

One Year Limited Warranty

CRAFTSMAN will repair or replace, without charge, any

defects due to faulty materials or workmanship for one year

from the date of purchase. This warranty does not cover

part failure due to normal wear or tool abuse. For further

detail of warranty coverage and warranty repair information,

visit www.craftsman.com or call 1-888-331-4569. This

warranty does not apply to accessories or damage caused

where repairs have been made or attempted by others.

THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS,

INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, AND EXCLUDES

ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some

states do not allow limitations on how long an implied

warranty lasts or the exclusion or limitation of incidental

or consequential damages, so these limitations may not

and you may have other rights which vary in certain states

or provinces.

90 DAY MONEY BACK GUARANTEE

your CRAFTSMAN Wireless Thermometer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

packaging, call the local company or see website for

warranty information.

FCC Radio Frequency Interference

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

To assure continued appliance, any changes or

mo ons not expressly approved by the party

responsible for compliance could voice the user's

authority to operate this equipment. (Example -use only

shielded interface cables when connecting to computer or

peripheral devices).

FCC Warning

Any Changes or mod ons not expressly approved by

the party responsible for compliance could void the user's

authority to operate the equipment.

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning

the equipment o and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

REGULATORY INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Canada Statement

This device contains licence-exempt transmitter(s)/receiver(s) that

comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to the

following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference

that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent

appareil est conforme aux CNR d’Innovation, Sciences et

Développement économique Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le

fonctionnement.

The device meets the exemption from the routine evaluation

limits in section 2.5 of RSS 102 and compliance with RSS-102 RF

exposure, users can obtain Canadian information on RF exposure

and compliance.

Le dispositif rencontre l'exemption des limites courantes

d'évaluation dans la section 2.5 de RSS 102 et la conformité à

l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information

canadienne sur l'exposition et la conformité de rf.

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.



Product Manufactured by:

Chaney Instrument Company

Lake Geneva, WI 53147

U.S. & Canada Only

08/20 01137LCM

Craftsman CMXWDCR01137 Manuel utilisateur

Marque: Craftsman

Modèle: CMXWDCR01137

Catégorie: Stations météo

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Craftsman CMXWDCR01137 User manual

Craftsman CMXWDCR01137 Manuel utilisateur

Craftsman CMXWDCR01137 Manuel utilisateur

dans d''autres langues

Autres documents