KitchenAid Architect Series II KDRS807SSS Guide d'installation

Marque: KitchenAid

Modèle: Architect Series II KDRS807SSS

Taper: Guide d'installation

Ce manuel convient également à

I_itchen_kid ®

INSTALLATION INSTRUCTIONS

30"(76.2 CM) FREESTANDING AND SLIDE-IN

DUAL FUEL RANGES

INSTRUCTIONS POUR L'INSTALLATION DES

CUISINIERES AUTOPORTANTES ET

ENCASTRABLES A BI-COMBUSTIBLE

DE 30"(76,2 CM)

Table of Contents/Table des matieres .................................................................................. 2

IMPORTANT:

Save for local electrical inspector's use.

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

IMPORTANT :

/_,conserver pour consultation par I'inspecteur local des installations electriques.

Installateur : Remettre les instructions d'installation au proprietaire.

Propri6taire : Conserver les instructions d'installation pour ref6rence ulterieure.

W10118264A

TABLE OF CONTENTS TABLE DES MATIERES

RANGE SAFETY ............................................................................. 2

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Electrical Requirements - U.S.A. Only ......................................... 7

Electrical Requirements - Canada Only ....................................... 8

Gas Supply Requirements ........................................................... 8

Countertop Preparation ............................................................... 9

INSTALLATION INSTRUCTIONS ................................................ 10

Unpack Range ............................................................................ 10

Measure for Proper Height......................................................... 10

Adjust Leveling Legs .................................................................. 11

Install Anti-Tip Bracket ............................................................... 11

Remove Warming Drawer .......................................................... 12

Verify Anti-Tip Bracket Location ................................................ 12

Level Range ................................................................................ 12

Electrical Connection - U.S.A. Only ........................................... 13

Make Gas Connection ............................................................... 16

Electronic Ignition System ......................................................... 17

Replace Oven Racks and Warming Drawer .............................. 18

Complete Installation ................................................................. 18

GAS CONVERSIONS .................................................................... 19

LP Gas Conversion .................................................................... 19

Natural Gas Conversion ............................................................. 21

ANTI-TIP BRACKET TEMPLATE ................................................ 39

S¢:CURITI_ DE LA CUISINII_RE ................................................... 23

EXIGENCES D'INSTALLATION ................................................... 24

Outillage et pieces ...................................................................... 24

Exigences d'emplacement ......................................................... 24

Specifications de I'installation electrique ................................... 27

Specifications de I'alimentation en gaz ..................................... 27

Preparation du plan de travail .................................................... 28

INSTRUCTIONS D'INSTALLATION ............................................. 29

Deballage de la cuisiniere .......................................................... 29

Mesures pour une hauteur appropriee ...................................... 29

Reglage des pieds de nivellement ............................................. 29

Installation de la bride antibasculement .................................... 30

Retrait du tiroir-rechaud ............................................................. 31

V_rification de I'emplacement de la bride antibasculement ......31

Reglage de I'aplomb de la cuisiniere ......................................... 31

Raccordement a la canalisation de gaz ..................................... 31

Systeme d'allumage electronique .............................................. 32

Reinstallation des grilles du four et du tiroir-rechaud ................ 33

Achever I'installation .................................................................. 34

CONVERSIONS POUR CHANGEMENT DE GAZ ....................... 34

Conversion pour I'alimentation au propane ............................... 34

Conversion pour I'alimentation au gaz naturel .......................... 37

GABARIT POUR LA BRIDE ANTIBASCULEMENT .................... 39

RANGE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

I WARNING: If the information in this manual is not followed exactly, a fire or explosion I

may result causing property damage, personal injury or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

In the State of Massachusetts, the following installation instructions apply:

[] installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

I_L_ I Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

IN STALLATION REQUIREMENTS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Tape measure • Masking tape

• Flat-blade screwdriver • Pipe-joint compound

resistant to LP gas

• Phillips screwdriver

• Level • 3/16"(4.8 mm) carbide-tipped

masonry drill bit (for

• Hand or electric drill concrete/ceramic floors)

• Hammer • Noncorrosiveleak-detection

solution

• Wrench or pliers

For LP/Natural Gas

• Pipe wrench

Conversions

• 15/16"combination wrench • 1/2"combination wrench

• %" nut driver • 7 mm combination wrench

• 1/4"nut driver • 7 mm nut driver

• 1/s"(3.2 mm) drill bit (for • Size T20 TORX _'tscrewdriver

wood floors)

• Marker or pencil

Parts supplied

Check that all partsareincluded.

S_,

A. Anti-tip bracket

B. Plastic anchors (2)

C. #!O x V2"screws (2)

Anti-tip brackets must be securely mounted to subfloor.

Thickness of flooring may require longer screws to anchor

bracket to subfloor. Longer screws are available from your

local hardware store.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See "Electrical Requirements" and

"Gas Supply Requirements" sections.

Rear Filler Strip (optional)

The filler strip may be used to fill a gap between the rear of the

slide-in range and the wall in a freestanding range cutout.

A. Filler strip

B. Countertop

C. Countertop cutout

To order, see the "Assistance or Service" section of the Use and

Care Guide. Order Part Number W10113902A (black),

W10113903A (white) or W10113904A (biscuit).

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct flow of combustion and ventilation air.

• It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located inside the oven door on

the right-hand side oven door trim.

• The range should be located for convenient use in the

kitchen.

• Recessed installations must provide complete enclosure of

the sides and rear of the range.

To eliminate the risk of burns or fire by reaching over heated

surface units, cabinet storage space located above the

surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood

or microwave hood combination that projects horizontally a

minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

• All openings in the wall or floor where range is to be installed

must be sealed.

• Do not seal the range to the side cabinets.

• Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

1-®TORX is a registered trademark of Textron Innovations Inc.

• The floor anti-tip bracket must be installed. To install the anti-

tip bracket shipped with the range, see "Install Anti-Tip

Bracket" section.

• Grounded electrical supply is required. See "Electrical

Requirements" section.

• Proper gas supply connection must be available. See "Gas

Supply Requirements" section.

• Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

• Use an insulated pad or 1/4"(0.64 cm) plywood under range if

installing range over carpeting.

iMPORTANT: Some cabinet and building materials are not

designed to withstand the heat produced by the oven for baking

and self-cleaning. Check with your builder or cabinet supplier to

make sure that the materials used will not discolor, delaminate or

sustain other damage.

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured Home

Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the

current standards CAN/CSA-A240-1atest edition, or with local

codes.

Mobile home installations require:

• When this range is installed in a mobile home, it must be

secured to the floor during transit. Any method of securing

the range is adequate as long as it conforms to the standards

listed above.

• Four-wire power supply cord or cable must be used in a

mobile home installation. The appliance wiring will need to be

revised. See "Electrical Connection" section.

Product Dimensions

Freestanding Range Slide-in Range

A. 53/4'' (14.6 cm)

B. 30" (76.2 cm)

C. 4!3/4 ''(106 cm) overall height

with leveling legs screwed all

the way in.

D. 36" (9!.4 cm) cooktop trim

height with leveling legs

screwed all the way in*

E.Model/serial number plate

(located on the right-hand

side oven door trim)

F. 27¼" (69.2 cm) max. from

handle to standoff at back

of range**

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)

countertop; front of oven door protrudes 1" (2.5 cm) beyond

24" (61 cm) base cabinet.

A. 30%6" (77.6 cm)

B. 35%" (90.5 cm) height to

underside of cooktop edge

with levering legs screwed

all the way in*

C. Model/serial number plate

(located on the right-hand

side oven door trim)

D 30" (76.2 cm)

E.27¼" (69.2 cm) from

handle to standoff at

back of range**

E 23" (58.4 cm) ceuntertop

notch to rear of cooktop

*Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)

countertop; front of oven door protrudes 13/4"(4.4 cm) beyond

24" (61 cm) base cabinet.

Installation Clearances

Cabinet opening dimensions shown are for 25" (64 cm) countertop depth, 24" (61 cm) base cabinet depth and 36" (91.4 cm)

countertop height.

Freestanding Ranges

A E _

" L_ _M

A. !8" (45.7 cm) upper cabinet to countertop

B. !3" (33 cm) upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to top of the cooktop, see NOTE.

E.30" (76.2 cm) min. opening width

F. This shaded area recommended for installation of rigid gas pipe.

G. 6" (!5.2 cm) available area for gas and electric installation

H. This shaded area recommended for installation of outlet or

junction box.

L 7" (17.8 cm)

J. 1V2"(3.8 cm)

K. 4W' (1!.4 cm)

L. 5" (!2.7 cm) min. clearance from both sides of the range to the

side waft or other combustible material.

M. Cabinet door or hinge should not extend into the cutouL

Slide-In Ranges

A. !8" (45.7 cm) upper cabinet to countertop

B. !3" (33 cm) max. upper cabinet depth

C. 30" (76.2 cm) rain. opening width

D. For minimum clearance to top of the cooktop, see NOTE.

E. 30" (76.2 cm) rain. opening width

F. This shaded area recommended for installation of rigid gas pipe.

G. 6" (15.2 cm) available area for gas and electric installation

H. This shaded area recommended for installation of outlet or

junction box.

L 7" (17.8 cm)

J. 1W' (3.8 cm)

K. 4W' (! 1.4 cm)

L. 5" (!2.7 cm) min. clearance from both sides of the range to the

side wall or other combustible material.

M. 2215A6"(58.3 cm) opening depth

N. _" (!.9 cm) radius both corners

O. Cabinet door or hinge should not extend into the cutout.

NOTE: 24" (61 cm) minimum when bottom of wood or metal cabinet is protected by not less than 1/4"(0.64 cm) flame retardant

millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an unprotected wood or metal cabinet.

If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination

installation instructions for dimensional clearances above the cooktop surface.

Ifcodespermitandaseparategroundwireisused,itis

recommendedthataqualifiedelectricalinstallerdeterminethat

thegroundpathisadequateandwiregaugeisinaccordance

withlocalcodes.

Donotuseanextensioncord.

Besurethattheelectricalconnectionandwiresizeareadequate

andinconformancewiththeNationalElectricalCode,ANSI/

NFPA70-latesteditionandalllocalcodesandordinances.

Acopyoftheabovecodestandardscanbeobtainedfrom:

NationalFireProtectionAssociation

OneBatterymarchPark

Quincy,MA02269

WARNING:Improperconnectionoftheequipment-grounding

conductorcanresultinariskofelectricshock.Checkwitha

qualifiedelectricianorservicetechnicianifyouareindoubtasto

whethertheapplianceisproperlygrounded.Donotmodifythe

powersupplycordplug.Ifitwillnotfittheoutlet,haveaproper

outletinstalledbyaqualifiedelectrician.

Thisrangeismanufacturedwiththeneutralterminalconnected

tothecabinet.Usea3-wire,ULlisted,40-amppowersupply

cord(pigtail);oriflocalcodesdonotpermitgroundthroughthe

neutral,usea4-wirepowersupplycordratedat250volts,

40ampsandinvestigatedforusewithranges.

ElectricalConnection

Toproperlyinstallyourrange,youmustdeterminethetypeof

electricalconnectionyouwillbeusingandfollowtheinstructions

providedforithere.

• Rangemustbeconnectedtotheproperelectricalvoltage

andfrequencyasspecifiedonthemodel/serialnumberrating

plate.Themodel/serialratingplateislocatedinsidetheoven

doorontheright-handsideovendoortrim.Refertothe

figuresinthe"ProductDimensions"sectionofthe"Location

Requirements"section.

Whena4-wireor3-wire,singlephase120/240volt,60Hz,

AConlyelectricalsupplyisavailable,a50-ampmaximum

circuitprotectionisrequired.Whena4-wireor3-wiresingle

phase120/208volt60Hz,AConlyelectricalsupplyis

available,a40-ampmaximumcircuitprotectionisrequired,

fusedonbothsidesoftheline.

• Atime-delayfuseorcircuitbreakerisrecommended.

Therangecanbeconnecteddirectlytothefuseddisconnect

(orcircuitbreakerbox)throughflexibleornonmetallic

sheathed,copperoraluminumcable.See"Electrical

Connection."

• Allow2to3ft(61.0cmto91.4cm)ofslackinthelinesothat

therangecanbemovedifservicingisevernecessary.

• AULlistedconduitconnectormustbeprovidedateachend

ofthepowersupplycable(attherangeandatthejunction

box).

• Wiresizesandconnectionsmustconformwiththeratingof

therange(40amps).

• Thewiringdiagramislocatedontheundersideofthestorage

drawerorbelowthewarmingdrawerinaclearplasticbag.

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the

cabinet. The ground must be revised so the green ground wire of

the 4-wire power supply cord is connected to the cabinet. See

"Electrical Connection."

Grounding through the neutral conductor is prohibited for new

branch-circuit installations (1996 NEC); mobile homes; and

recreational vehicles, or an area where local codes prohibit

grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a

matching UL listed, 4-wire, 250 volt, 40-amp, range power supply

cord (pigtail) must be used. This cord contains 4 copper

conductors with ring terminals or open-end spade terminals with

upturned ends, terminating in a NEMA Type 14-50R plug on the

supply end.

The fourth (grounding) conductor must be identified by a green or

green/yellow cover and the neutral conductor by a white cover.

Cord should be Type SRD or SRDT with a UL listed strain relief

and be at least 4 ft (1.22 m) long.

4-wire receptacle (14-50R)

The minimum conductor sized for the copper 4-wire power

cord are:

40-amp circuit

2 No.-8 conductors

1 No.-10 white neutral

1 No.-8 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire,

250 volt, 40-amp range power supply cord (pigtail). This cord

contains 3 copper conductors with ring terminals or open-end

spade terminals with upturned ends, terminating in a NEMA Type

10-50P plug on the supply end. Connectors on the appliance end

must be provided at the point the power supply cord enters the

appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

3-wire receptacle (10-50R)

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death, fire, or

electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path is adequate and wire gauge are in accordance

with local codes.

Be sure that the electrical connection and wire size are adequate

and in conformance with CSA Standard C22.1, Canadian

Electrical Code, Part 1 - latest edition, and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

Canadian Standards Association

178 Rexdale Blvd.

Toronto, ON M9W 1R3 CANADA.

• Check with a qualified electrical installer if you are not sure

the range is properly grounded.

When a 4-wire, single phase 120/240 volt, 60 Hz., AC only

electrical supply is available, a 50-amp maximum circuit

protection is required (or, if specified on the model/serial

rating plate, when a 4-wire, single phase 120/208 volt 60 Hz.,

AC only electrical supply is available, a 40-amp maximum

circuit protection is required), fused on both sides of the line.

• A time-delay fuse or circuit breaker is recommended.

This range is equipped with a CSA International Certified

Power Cord intended to be plugged into a standard 14-50R

wall receptacle. Be sure the wall receptacle is within reach of

range's final location.

• Do not use an extension cord.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column,

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest

edition.

IMPORTANT: Leak testing of the range must be conducted

according to the manufacturers instructions.

Type of Gas

Natural gas:

This range is design-certified by CSA International for use with

Natural gas or, after proper conversion, for use with LP gas.

• This range is factory set for use with Natural gas. See "Gas

Conversions" section. The model/serial rating plate located

on the right side oven door trim has information on the types

of gas that can be used. If the types of gas listed do not

include the type of gas available, check with the local gas

supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See "Gas

Conversions" section.

Gas Supply Line

Provide a gas supply line of 3A"(1.9 cm) rigid pipe to the

range location. A smaller size pipe on longer runs may result

in insufficient gas supply. Pipe-joint compounds that resist

the action of LP gas must be used. Do not use TEFLON _'t

tape. With LP gas, piping or tubing size can be r/2"(1.3 cm)

minimum. Usually, LP gas suppliers determine the size and

materials used in the system.

1-CeTEFLON is a registered trademark of E.I Du Pont De Nemours and Company

Flexible metal appliance connector:

If local codes permit, a new CSA design-certified,

4 - 5 ft (122 - 152.4 cm) long, 1/2"(1.3 cm) or

3A"(1.9 cm) I.D., flexible metal appliance connector may

be used for connecting range to the gas supply line.

• A 1/2"(1.3 cm) male pipe thread is needed for connection

to the female pipe threads of the inlet to the appliance

pressure regulator.

• Do not kink or damage the flexible metal tubing when

moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the range. The rigid

pipe must be level with the range connection. All strains must

be removed from the supply and fuel lines so range will be

level and in line.

Must include a shutoff valve:

The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but

external to the range. It should be in a location that allows

ease of opening and closing. Do not block access to shutoff

valve. The valve is for turning on or shutting off gas to the

range.

A.Gassupply line

B.Shutoff valve"open" position

C. Torange

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural gas:

Minimum pressure: 5" WCP

Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP

Maximum pressure: 14" WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at a

rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Line pressure testing above 1/2psi gauge (14" WCP)

The range and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures in excess of 1/2psi (3.5 kPa).

Line pressure testing at 1/2psi gauge (14" WCP) or lower

The range must be isolated from the gas supply piping system by

closing its individual manual shutoff valve during any pressure

testing of the gas supply piping system at test pressures equal to

or less than 1/2psi (3.5 kPa).

................. <. ......

The cooktop sides of the slide-in range fit over the cutout edge of

your countertop.

If you have a square finish (flat) countertop and the opening width

is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops must have molded edge

shaved flat %" (1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back %" (1.0 cm) from each

front corner and/or rounded edge flattened.

30"

(76.2 cm)

\ 303/4" /

(78.1 crn)

If countertop opening width is greater than 30" (76.2 cm), adjust

the %" (1.0 cm) dimension.

Countertop must be level. Place level on countertop, first side to

side, then front to back. If countertop is not level, range will not

be level. Range must be level for satisfactory baking conditions.

INSTALLATION INSTRUCTIONS

2. Measure from the floor to the underside of the range cooktop.

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. Remove shipping materials, tape and protective film from the

range. Keep cardboard bottom under range. Remove oven

racks and parts package from inside oven.

2. To place range on its back, take 4 cardboard corners from the

carton. Stack one cardboard corner on top of another.

Repeat with the other 2 corners. Place them lengthwise on

the floor behind the range to support the range when it is laid

on its back. Using 2 or more people, firmly grasp the range

and gently lay it on its back on the cardboard corners.

3. Pull cardboard bottom firmly to remove.

Slide-In Ranges:

1. Measure the distance of the countertop to the floor. Measure

at all 4 locations corresponding to the 4 corners of the

underside of the range cooktop, as shown.

A. Distance from the floor to C. Cooktop surface

underside of range cooktop D. Range side frame

B. Grate

3. Your leveling height will be the difference between the

2 measurements you have just taken.

Freestanding Ranges:

1. Measure the distance of the countertop to the floor.

2. Measure from the top of the range cooktop trim to the floor.

A. Distance from the top of the range

cooktop trim to the floor

Your leveling height will be the difference between the

2 measurements you have just taken.

Measure at locations marked A, B, C, D.

If range height adjustment is necessary, use a wrench or

pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range

supported on 2 legs after the range has been placed back to

a standing position.

NOTE: To place range back up into a standing position, put a

sheet of cardboard or hardboard in front of range. Using 2 or

more people, stand range back up onto the cardboard or

hardboard.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

Adjust the leveling legs to the correct height. Leveling legs

can be loosened to add up to a maximum of 1" (2.5 cm). A

minimum of 3_6"(5 mm) is needed to engage the anti-tip

bracket.

NOTE: If height adjustment is made when range is standing,

tilt the range back to adjust the front legs, then tilt forward to

adjust the rear legs.

When the range is at the correct height, check that there is

adequate clearance under the range for the anti-tip bracket.

Before sliding range into its final location, check that the anti-

tip bracket will slide under the range and onto the rear

leveling leg prior to anti-tip bracket installation.

Contact a qualified floor covering installer for the best procedure

for drilling mounting holes through your type of floor covering.

Before moving range, slide range onto shipping base, cardboard

or hardboard.

1. Remove template from the anti-tip bracket kit (found inside

the oven cavity) or from the back of this manual.

2. Place template on the floor in cabinet opening so that the left

edge is against cabinet and top edge is against rear wall,

molding or cabinet.

3. Tape template into place.

If countertop is not flush with cabinet opening edge, align

template with overhang.

If cabinet opening is wider than that specified in the "Location

Requirements" section, adjust template so range will be

centered in cabinet opening.

To mount anti-tip bracket to wood floor, drill two %" (3.2 mm)

holes at the positions marked on the bracket template.

Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor, use a

3/16"(4.8 mm) masonry drill bit to drill 2 holes at the positions

marked on the bracket template. Remove template from floor.

6. Tap plastic anchors into holes with a hammer.

7. Align anti-tip bracket holes with holes in floor. Fasten anti-tip

bracket with screws provided.

Depending on the thickness of your flooring, longer screws

may be necessary to anchor the bracket to the subfloor.

Longer screws are available from your local hardware store.

8. Move range close enough to opening to allow for final

electrical connection. Remove shipping base, cardboard or

hardboard from under range.

9. Move range into its final location making sure rear leveling leg

slides into anti-tip bracket.

10. If installing the range in a mobile home, you must secure the

range to the floor. Any method of securing the range is

adequate as long as it conforms to the standards in the

"Location Requirements" section.

11. Continue installing your range using the following installation

instructions.

Remove the warming or storage drawer to gain access to the

lower section of the range. This will be necessary for some of the

following installation steps.

To Remove Warming Drawer:

1. Open drawer to its fully open position.

2. Locate the black loops on both sides of the drawer.

A.Loop

Pull both loops forward at the same time, then pull drawer out

another inch.

IMPORTANT: On models with a warming drawer, the rear range

foot must be viewed from the front and slightly to one side of the

range,

1. Making sure the anti-tip bracket is installed:

• Look for the anti-tip bracket securely attached to floor.

• Slide range back so rear range foot is under anti-tip

bracket.

If installing the range in a mobile home, you must secure the

range to the floor. Any method of securing the range is

adequate as long as it conforms to the standards in the

"Location Requirements" section.

Holding the drawer by its sides, not its front, gently pull it all

the way out.

Place rack in oven. Place level on rack and check levelness of the

range, first side to side; then front to back.

If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

Use a wrench or pliers to adjust leveling legs up or down until the

range is level. Push range back into position. Check that rear

leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

Power Supply Cord Direct Wire

Electrical Shock Hazard

Disconnect power before servicing.

Use a new 40 amp power supply cord.

Plug into a grounded outlet.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper or 6 gauge aluminum wire.

Electrically ground range.

Failure to follow these instructions can result in death,

fire, or eJectrical shock.

Disconnect power.

Remove the terminal block cover screws located on the back

of the range. Pull cover down and toward you to remove

cover.

A. Hold-down screws

B. Terminal block cover

Feed the power supply cord behind the black horizontal

cross brace and through the strain relief, allowing enough

slack to easily attach the wiring to the terminal block.

A. Black horizontal cross brace

B. Power supply cord

• Tighten strain relief screw against the power supply cord.

3= Add strain relief.

Style 1: Power supply cord strain relief

Remove the knockout for the 40-amp supply cord.

Assemble a UL listed strain relief in the opening.

A. UL listed strain relief

Style 2: Direct wire strain relief

• Remove the knockout as needed for the flexible conduit

connection.

• Assemble a UL listed conduit connector in the opening.

A. Removable retaining nut

B. Strain relief

Feed the flexible conduit behind the black horizontal

cross brace and through the strain relief, allowing enough

slack to easily attach the wiring to the terminal block.

A. Black horizontal cross brace

B.Flexibleconduit

• Tighten strain relief screw against the flexible conduit.

Complete installation following instructions for your type of

electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section:

connecting to:

4-wire receptacle A UL listed,

(NEMA type 14-50R) 250-volt

minimum,

40-amp, range

power supply

cord

4-wire connection:

Power supply cord

4-wire direct A fused 4-wire connection:

disconnect or Direct wire

circuit breaker

(12.7 crn) box

3-wire receptacle A UL listed, 3-wire connection:

(NEMA type 10-50R) 250-volt Power supply cord

minimum,

40-amp, range

power supply

cord

3-wire direct A fused

_., disconnect or

(2•5o_.\ circuit breaker

_, box

3-wire connection:

Direct wire

4-wire connection: Power Supply Cord

Use this method for:

• New branch-circuit installations (1996 NEC)

• Mobile homes

• Recreational vehicles

• In an area where local codes prohibit grounding through the

neutral

1. Remove the ground-link screw from the range frame. Save

the ground link screw and cup washer. Bend the ground-link

away from the range so that it does not contact the range.

.............. C

B ....................

A ...................

A. Ground-link screw

B. Cup washer

C. Ground-link bent away from range

2. Connect the green ground wire from the power supply cord to

the range using the ground-link screw. The ground wire must

be attached first and must not contact any other terminal.

3. Use a V4"nut driver and remove the hex washer head screws

from the terminal blocks•

Connect the neutral (center) wire to the center terminal

connector using one of the hex washer head screws.

Securely tighten screw for proper electrical connection.

3. Connect the other 2 wires (lines 1 and 2) to the outer terminal

screws on the terminal block.

4. Tighten strain relief screws.

5. Replace terminal block cover.

Direct Wire Installation: Copper or Aluminum Wire

This range may be connected directly to the fuse disconnect or

circuit breaker box. Depending on your electrical supply, make

the required 3-wire or 4-wire connection.

1. Strip outer covering back 3" (7,6 cm) to expose wires. Strip

the insulation back 1" (2.5 cm) from the end of each wire.

A. Line !

B. Green ground wire

C. Ground-link screw

D. Hex washer head screw

E. Silver-colored terminal

block screw

E Ground-link

G. Neutral (center) wire

H. Line 2

L UL listed strain relief and

40-amp range power

supply cord

5. Connect the other 2 wires (lines 1 and 2) to the outer

aluminum terminal blocks.

6. Securely tighten screws for proper electrical connection.

7. Tighten strain relief screws.

8. Replace terminal block cover.

3-wire connection: Power Supply Cord

Use this method only if local codes permit connecting cabinet-

ground conductor to neutral wire of power supply cord,

1. Use a 1/4"nut driver and remove the hex washer head screws

from the aluminum terminal blocks,

2. Connect the neutral (center) wire to the center terminal

connector using one of the hex washer head screws.

Securely tighten screw for proper electrical connection.

A. Line 1

B. Ground-link

C. Hex washer head screw

D. Silver-colored terminal

block screw

E. Neutral (center) wire

F. Line 2

G. UL listed strain relief

and 40-amp range power

supply cord

(7.6 crn)

2. Allow enough slack in the wire to easily attach the wiring

terminal block,

3. Complete electrical connection according to your type of

electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

• New branch-circuit installations (1996 NEC)

• Mobile homes

• Recreational vehicles

• In an area where local codes prohibit grounding through the

neutral

1. Remove the ground-link screw from the range frame, Save

the ground-link screw and cup washer. Bend the ground-link

away from the range so that it does not contact the range,

A.Ground-link screw

B.Cup washer

C.Ground-link bent away from range

2. Connect the bare ground wire to the range using the ground-

link screw and cup washer. The ground wire must be

attached first and must not contact any other terminal.

A. Bare wire from power

supply cable

B. Line 1

C. Hex washer head screw

D. Silver-colored terminal

block screw

E. Line 2

F. Neutral (white) wire

G. UL listed conduit

connector and power

supply cable

3. Loosen (do not remove) the hex washer head screw and

insert the neutral (white) wire under the screw clamp at the

bottom of the center position terminal connector.

4. Insert the other 2 wires (lines 1 and 2) under the other 2 screw

clamps.

A. Insert wire under screw clamp.

B. Hex washer head screw

5. Securely tighten the hex washer head screws to

35 Ibs-in. (4.0 N-m) minimum torque to make proper

electrical connection.

6. Tighten the locking ring of the conduit connector.

7. Replace the terminal block cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground

conductor to neutral supply wire.

1. Loosen (do not remove) the hex washer head screws and

insert the neutral (white) wire under the screw clamp at the

bottom of the center position terminal connector.

Insert the other 2 wires (lines 1 and 2) under the other 2 screw

clamps.

A. Insert wire under screw clamp.

B. Hex washer head screw

3. Securely tighten the hex washer head screws to

35 Ibs-in. (4.0 N-m) minimum torque to make a proper

electrical connection.

4. Tighten the locking ring of the conduit connector.

5. Replace the terminal block cover.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 crn) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Typical rigid pipe connection

A combination of pipe fittings must be used to connect the range

to the existing gas line. Your connections may be different,

according to the supply line type, size and location.

1. Apply pipe-joint compound made for use with LP gas to all

pipe thread connections.

A. Line 1

B. Ground-link

C. Hex washer head screw

D. Silver-colored terminal

block screw

E.Neutral (white) wire

F. Line 2

G. UL listed conduit

connector and power

supply cable

2. Using a pipe wrench to tighten, connect the gas supply to the

range.

B F:

A C D

A. Y_"or _A"gas pipe

B. Manual gas shutoff valve

C. Nipple

D. Union

E.90 °elbow

F. Black iron pipe

G. Union

H. Nipple

I.90 ° elbow (must have

V2"male pipe thread)

J. Gas pressure regulator

Typical flexible connection

1. Apply pipe-joint compound made for use with LP gas to the

smaller thread ends of the flexible connector adapters (see C

and G in the following illustration).

2. Attach one adapter to the gas pressure regulator and the

other adapter to the gas shutoff valve. Tighten both adapters.

3. Use a 15/16"combination wrench and channel lock pliers to

attach the flexible connector to the adapters. Check that

connector is not kinked,

E F

A c

A. ½" or 3/4"gas pipe

B. Manual gas shutoff valve

C. Use pipe-joint compound.

D. Adapter

E.Flexible connector

E Adapter (must have Y_"male

pipe thread)

G. Use pipe-joint compound.

H. Gas pressure regulator

Complete Connection

1. Open the manual shutoff valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

If burner caps are not properly positioned, surface burners

will not light.

C .....

A. Burner base

B. Burner cap

C. Burner grate

Place burner grates over burners and caps as shown in the

following illustration, When properly installed the grates

should not overlap the console.

Freestanding Ranges

A J " "_.......

A. Opening in grate for wok insert to be

located over left front burner.

Slide-In Ranges

A. Large flange with rounded corner must be at

rear corner of the cooktop

Plug in range or reconnect power. "Clock-Enter Time" should

appear in the display, For further information, please refer to

the user instructions located in the Use and Care Guide.

A. Closed valve

B. Open valve

2. Test all connections by brushing on an approved

noncorrosive leak-detection solution. If bubbles appear, a

leak is indicated. Correct any leak found.

3. Remove cooktop burner caps and grates from parts

package. Align notches in burner caps with pins in burner

base. Burner caps should be level when properly positioned.

Initial lighting and gas flame adjustments

Cooktop burners use electronic igniters in place of standing

pilots, When the cooktop control knob is turned to the "LITE"

position, the system creates a spark to light the burner. This

sparking continues, as long as the control knob is turned to

"LITE,"

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the "LITE" position,

The flame should light within 4 seconds. The first time a burner is

lit it may take longer that 4 seconds to light because of air in the

gas line.

TripleTier _ Flame Burner

To start simmer burner:

Push in and turn control knob to "LITE."

The flame should light within 4 seconds. The first time a burner is

lit it may take longer that 4 seconds to light because of air in the

gas line.

To start power burner:

Push in control knob again and turn to "POWER BURNER HI" to

light the outer burner.

The flame should light within 4 seconds. The first time a burner is

lit it may take longer that 4 seconds to light because of air in the

gas line.

If burners do not light properly:

• Turn cooktop control knob to the "OFF" position.

Check that the range is plugged in and the circuit breaker has

not tripped or the household fuse has not blown.

Check that the gas shutoff valves are set to the "open"

position.

Check that burner caps are properly positioned on burner

bases.

Repeat start-up. If a burner does not light at this point, turn

control knobs to "Off" and contact your dealer or authorized

service company for assistance.

Adjust Flame Height

Adjust the height of top burner flames. The cooktop "low" burner

flame should be a steady blue flame approximately 1/4"(0.64 cm)

high.

To adjust TripleTier ®Flame burner:

1. Remove the control knob.

2. Insert a flat-blade screwdriver into adjustment locations

shown in the following illustration and engage the slotted

screw. Turn the screw until the flame is the proper size.

A. Simmer burner regulation

B. Power burner regulation

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI,"

checking the flame at each setting.

Replace oven racks in oven cavity. Replace warming drawer or

storage drawer.

To Replace Warming Drawer:

1. Align the drawer glides with the receiving guides.

2. Push drawer in all the way.

Gently open and close the drawer to ensure it is seated properly

on the slides.

A. Low flame

B. High flame

To adjust standard burners:

The flame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly

underneath the control knob.

.....,,®'

A _

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that range level. See "Level Range."

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by protective shipping

material. Dry thoroughly with a soft cloth. For more

information, see the "Range Care" section of the Use and

Care Guide.

6. Read "Range Use" in the Use and Care Guide.

7. Turn on surface burners and oven. See the Use and Care

Guide for specific instruction on range operation.

A. Valve stem

If the "low" flame needs to be adjusted:

1. Remove the control knob.

2. Hold the knob stem with a pair of pliers. Use a small flat-

blade screwdriver to turn the screw located in the center of

the control knob stem until the flame is the proper size.

3. Replace the control knob.

4. Test the flame by turning the control from "LO" to "HI,"

checking the flame at each setting.

If range does not operate, check the following: •

• Household fuse is intact and tight, or circuit breaker has not •

tripped.

• Gas valves are turned to the "open" position.

• If the gas supply line shutoff valve is open, press the OFF

button on the oven control panel and contact a qualified

technician.

Electrical supply is connected.

See "Troubleshooting" in the Use and Care Guide.

When the range has been on for 5 minutes, check for heat. If

range is cold, turn off the range and contact a qualified

technician.

GAS CONVERSIONS

Gas conversions from Natural gas to LP gas; or from LP gas to

Natural gas must be done by a qualified installer.

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

To Convert Gas Pressure Regulator

1. Turn manual shutoff valve to the "closed" position.

2. Unplug range or disconnect power.

...............B

J_ __ .............................C

A. To range

B. Manual shutoff valve "closed" position

C. Gas supply line

3. Remove warming drawer. See the "Remove Warming

Drawer" section for instructions. Locate gas pressure

regulator at rear of warming drawer compartment.

4. Remove access cover from the gas pressure regulator.

A. Gas pressure regulator

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death

or serious burns to children and adults.

IMPORTANT: Do not remove the gas pressure regulator.

Gas pressure regulator

5. Remove the access cap by using a wrench, turning the

access cap counterclockwise.

6. Remove spring retainer from the cap by pushing against the

flat side of the spring retainer. Look at the spring retainer to

locate the "NAT" or "LP" position.

7. Turn over the spring retainer so the "LP" is showing on the

bottom.

8. Snap the spring retainer back into the cap.

9. Reinstall the cap onto the regulator.

E D C

A. Access cap D. Spring retainer

B. Gasket LP position

C. Gas pressure regulator E.Spring retainer

NAT position

To Convert Standard Surface Burners

1. Remove burner cap.

2. Using a T20 TORX ®screwdriver, remove the burner base.

3. Apply masking tape to the end of a 7 mm nut driver to help

hold the gas orifice spud in the nut driver while changing it.

Press nut driver down onto the gas orifice spud and remove

by turning it counterclockwise and lifting out. Set gas orifice

spud aside.

A. Igniter electrode

B. Gas tube opening

C. Burner cap

D. Burner base

Gas orifice spuds are stamped with a number, marked with

1 color dot, and have a groove in the hex area. Replace the

Natural gas orifice spud with the correct LP gas orifice spud.

A. Groove

Refer to the following chart for correct LP gas orifice spud

placement.

LP Gas Orifice Spud Chart for Standard Surface Burners

Burner Location Burner Rating Color Size

Right front 5,000 Btu/h Red 0.70 mm

Left front 13,000 Btu/h Green 1.10 mm

Right rear 10,000 Btu/h Blue 0.95 mm

Left rear 5,000 Btu/h Red 0.70 mm

5. Place Natural gas orifice spuds in plastic parts bag for future

use and keep with literature package.

6. Replace burner cap.

7. Repeat steps 1-6 for the remaining burners, except for the

TripleTier _'Flame burner (on some models). See "To Convert

TripleTier _'Flame Burners" section.

To Convert TripleTier _ Flame Burners (on some models)

1. Remove burner cap.

2. Remove the burner head using a size T20 TORX ®screwdriver.

3. Remove the plate on the external gas orifice spud.

A. Burner caps

B. Burner heads

C. External gas orifice spud access plate

D. Internal gas orifice spud

IMPORTANT: The TripleTier ®Flame burner has 2 gas orifice

spuds. Do not forget to change the external gas orifice spud

located under the plate.

A. Plate

B. External gas orifice spud

C. Internal gas orifice spud

4. Apply masking tape to the end of a 7 mm nut driver to help

hold the internal gas orifice spud in the nut driver while

changing it. Press nut driver down onto the internal gas

orifice spud and remove by turning it counterclockwise and

lifting out. Set internal gas orifice spud aside.

5. Use a 7 mm combination wrench to remove the external gas

orifice spud. Turn counterclockwise to remove. Set external

gas orifice spud aside.

6. Replace the Natural gas orifice spud with the correct LP gas

orifice spud. Refer to the following chart for correct LP gas

orifice spud placement.

La page charge ...

KitchenAid Architect Series II KDRS807SSS Guide d'installation

Marque: KitchenAid

Modèle: Architect Series II KDRS807SSS

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid Architect Series II KDRS807SSS Installation guide

KitchenAid Architect Series II KDRS807SSS Guide d'installation

Ce manuel convient également à

KitchenAid Architect Series II KDRS807SSS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents