Edge-Core AS7816-64X Manuel utilisateur

Edge-Core
Marque
Edge-Core
Modèle
AS7816-64X
Taper
Manuel utilisateur

Ce manuel convient également à

– 1 –
Quick Start Guide
Attach the Brackets
1. Attach each of the front- and rear-post brackets to the switch
using four of the included bracket screws.
2. Use an additional two screws to secure each of the rear-post
brackets at the mid-point on the sides of the switch.
3. Use the screws and cage nuts supplied with the rack to secure
the switch in the rack.
Adjust Rear-Post Bracket Ears
1. Lock the position of the rear-post bracket ears using the included
position-locking screws.
You can also adjust the rear-post bracket ears to fit different rack
depths from 56 cm to 75 cm.
Ground the Switch
1. Ensure the rack is properly grounded and in compliance with
ETSI ETS 300 253. Verify that there is a good electrical
connection to the grounding point on the rack (no paint or
isolating surface treatment).
Caution:
The switch includes plug-in power supply (PSU)
and fan tray modules that are installed into its chassis. All
installed modules must have a matching airflow direction.
That is, if the installed power modules have a front-to-back
(F2B) airflow direction, all the installed fan tray modules
must also have a F2B airflow direction.
Attention:
Le commutateur comprend des modules
d'alimentation et de bac de ventilateurs installés sur son
châssis. Tous les modules installés doivent avoir une
direction de circulation d'air correspondante. C'est-à-dire
que tous les modules doivent avoir la même direction de
circulation d'air: avant vers arrière (F2B), ou arrière vers
avant (B2F).
Note:
The switch has the Open Network Install
Environment (ONIE) software installer preloaded on the
switch, but no switch software image. Information about
compatible switch software can be found at
www.edge-core.com.
Note:
The switch drawings in this document are for
illustration only and may not match your particular switch
model.
1
1
1
2
3
Caution:
Installing the switch in a rack requires two
people. One person should position the switch in the rack,
while the other person secures it using the rack screws.
Attention:
Deux personnes sont nécessaires pour installer
un commutateur dans un bâti: La première personne va
positionner le commutateur dans le bâti, la seconde va le
fixer avec des vis de montage.
2
1
3
1
2
E062020-AP-R04
150200002012A
www.edge-core.com
64-Port 100G Top-of-Rack Switch
AS7816-64X
1.
100G Top-of-Rack Switch
AS7816-64X
2. Rack mounting kit—2 front-post brackets, 2 rear-post
brackets, 20 screws, and 2 ear-locking screws
3. AC power cord
4. DC power cable included with 48VDC PSU only (optional)
5. Console cable—RJ-45 to DB-9
6. Grounding kit—One grounding lug, 2 M5 screws and 2
washers (For AC PSU)
7. Grounding kit—One grounding lug, 4 ring lugs, 2 M5 screws
and 2 washers (For DC PSU)
8. Documentation—Quick Start Guide (this document) and
Safety and Regulatory Information
1
Package Contents
2 3 5 874
*150200002012A_R04*
6
Quick Start Guide
– 2 –
2. Attach a #10 AWG grounding wire (not included) to the
grounding point on the switch rear panel. Then connect the
other end of the wire to rack ground.
Connect Power
1. Install one or two AC or DC PSUs in the switch.
The switch supports up to two PSUs that must have the same
matching airflow direction as the installed fan trays.
2. Connect an external AC or DC power source to the PSUs.
1. Connect the RTN return. (red wire).
2. Connect the -36 – -72 VDC (black wire).
3. Connect the Chassis Ground (yellow-green wire).
Verify Switch Operation
1. Verify basic switch operation by checking the system LEDs.
When operating normally, the PSU1/PSU2, Diag, and Fan LEDs
should all be on green.
Perform Initial System Boot
1. If the network operating system (NOS) installer is located on a
network server, first connect the RJ-45 Management (Mgmt) port
to the network using 100-ohm Category 5, 5e or better twisted-
pair cable. (Not required if the NOS installer is located on
attached storage.)
2. Boot the switch. Wait for the ONIE software to locate and
execute the NOS installer, and then wait for the installer to load
the NOS software image.
Subsequent switch boots will bypass ONIE and directly run the
NOS software.
Connect Network Cables
1. For the RJ-45 Management port, connect 100-ohm Category 5,
5e or better twisted-pair cable.
2. Connect DAC cables to the QSFP28 slots. Or first install
QSFP28 transceivers and then connect fiber optic cabling to the
transceiver ports.
The following transceivers are supported:
■
100GBASE-CR4, AOC, SR4, LR4, and PSM4
■
40GBASE-CR4, SR4, and LR4
Caution:
The earth connection must not be removed unless
all supply connections have been disconnected.
Attention:
Le raccordement à la terre ne doit pas être retiré
sauf si toutes les connexions d’alimentation ont été
débranchées.
Caution:
Use a UL/IEC/EN 60950-1 certified power
supply to connect to a DC converter, and a #10 AWG (for -
36 VDC to -72 VDC PSU) wire to connect to a DC PSU.
Attention
: Utilisez une alimentation certifiée UL/IEC/EN
60950-1 pour le connecter à un convertisseur CC et un
câble AWG #10 (pour -36 VDC à -72 VDC) pour vous
connecter à une alimentation CC.
4
1
2
1
2
3
Note:
For switches with ONIE software pre-loaded, refer to
the network operating system (NOS) installer and NOS
documentation for details on software options and set up for
ONIE.
5
1
6
7
3
2
1
Quick Start Guide
– 3 –
3. As connections are made, check the port status LEDs to be sure
the links are valid.
Each QSFP28 port has four LEDs that indicate valid links in the
following modes:
■
1 LED Blue — 100 Gbps mode
■
1 LED Orange — 40 Gbps mode
■
1-4 LEDs White — 25 Gbps breakout mode (four lanes)
■
1-4 LEDs Green — 10 Gbps breakout mode (four lanes)
■
1 and 3 LED Magenta – 50 Gbps breakout mode (two
lanes)
Power and Battery Safety
Warning:
If your switch uses a lithium battery, do not attempt
to replace the battery yourself. Return the switch to the
manufacturer for battery replacement.
Avertissement:
Si votre commutateur utilise une batterie au
lithium, n'essayez pas de la remplacer vous-même. Renvoyez le
commutateur au fabricant pour le remplacement de la batterie.
If the switch contains lithium batteries that are encased in a
sealed chassis, do not attempt to open the sealed chassis under
any circumstances.
Si le commutateur contient des batteries au lithium enfermées
dans un châssis scellé, n'essayez en aucun cas d'ouvrir le
châssis scellé.
Risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Risque d'explosion si la batterie est remplacée par un type
incorrect. Éliminez les piles usagées conformément aux
instructions.
Caution - Risk of Electrical Shock:
To disconnect
power, remove all power cords from the unit.
Attention - Risque de Choc Électrique:
Pour
débrancher, l’alimentation électrique, veuillez assurer tous
les cables d’alimentation sont retires de l’unite.
注意 - 感電の危 : 電源を切る場合は 、 電源コ - トを本装置から抜いて
くたさい 。
注意 - 有觸電的危險：如要切斷電源 , 請將全部電源線都從機器上拔掉
注意 - 有触电的危险：如要切断电源 , 请将全部电源线都从机器上拔掉
Switch Chassis
Size (WxDxH) 438.4 x 580 x 87.7 mm (17.26 x 22.83 x 3.45 in.)
Weight 14.11 kg (31.1 lb), with two installed PSUs
Temperature Operating: 0° C to 45° C (32° F to 113° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 5% to 95% (non-condensing)
Power
Consumption
850 Watts maximum
PSUs
AC Power Rating 100-240Vac , 50-60Hz,12-6A, 850 Watts
DC Power Rating -36 – -72 VDC, 28–14 A, 850 Watts
Regulatory Compliances
Emissions EN 55032:2015+AC:2016, Class A
EN 61000-3-2:2014, Class A
EN 61000-3-3:2013
47 CFR FCC Part 15:2017, Subpart B, Class A
CE Mark
Immunity EN 55024:2010+A1:2015
IEC 61000-4-2/3/4/5/6/8/11
Safety UL (CSA 22.2 No 60950-1 & 62368-1; UL60950-
1 & 62368-1)
CB (IEC/EN60950-1 & 62368-1)
NOM
CCC
Hardware Specifications
  • Page 1 1
  • Page 2 2
  • Page 3 3

Edge-Core AS7816-64X Manuel utilisateur

Edge-Core
Marque
Edge-Core
Modèle
AS7816-64X
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents