Reznor R6GN Guide d'installation

Marque: Reznor

Modèle: R6GN

Taper: Guide d'installation

Ce manuel convient également à

R6GN 12.5 - 15 Ton

R6GN - 150 / 180 Series High Efﬁciency

R6GN-150 Series Shown

Single Package Gas Heating / Electric Cooling Rooftop Units

DO NOT DESTROY THIS MANUAL. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

FIRE OR EXPLOSION HAZARD

•Failure to follow safety warnings exactly

could result in serious injury or property

damage.

•Installationandservicemustbeperformed

byaqualiedinstaller,serviceagencyorthe

gassupplier.

•Do not store or use gasoline or other

ammablevaporsandliquidsinthevicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

•Donottrytolightanyappliance.

•Donottouchanyelectricalswitch;donot

useanyphoneinyourbuilding.

•Leavethebuildingimmediately.

•Immediatelycall your gassupplierfroma

neighbor’sphone.Followthegassupplier’s

instructions.

•Ifyoucannotreachyourgassupplier,call

theredepartment.

WARNING:

RISQUED’INCENDIEOUD’EXPLOSION

•Le non-respect des avertissements de

sécurité pourrait entraîner des blessures

graves,lamortoudesdommagesmatériels.

•L’installation et l’entretien doivent être

effectués par un installateur qualié, un

organismedeserviceoulefournisseur de

gazstaller,serviceagencyorthegassupplier.

•Nepasentreposerniutiliserdel’essenceni

d’autres vapeurs ou liquides inammables

danslevoisinagedecetappareil,nidetout

autreappareil.

QUEFAIRES’ILYAUNEODEURDEGAZ

•Nepastenterd’allumeraucunappareil.

•Netoucheràaucuninterrupteurélectrique;

n’utiliseraucuntéléphonedanslebâtiment.

•Évacuerl’immeubleimmédiatement.

•Appeler immédiatement le fournisseur de

gazenemployantletéléphoned’unvoisin.

Respecter à la lettre les instructions du

fournisseurdegaz.

•Sipersonnenerépond,appelerleservicedes

incendies.

AVERTISSEMENT

INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INFORMATION .......................3

REQUIREMENTS & CODES .......................................4

GENERAL INFORMATION ..........................................5

About the Rooftop Unit ..............................................5

Before You Install This Equipment .............................5

Locating the Unit .......................................................5

Heating Load .............................................................5

COMBUSTION AIR & VENTING REQUIREMENTS ....6

General Information ...................................................7

Vent Termination ........................................................7

CIRCULATING AIR SUPPLY .......................................8

Air Ducts ....................................................................8

Air Filter Requirements..............................................8

Unconditioned Spaces ..............................................9

Acoustical Ductwork ..................................................9

UNIT INSTALLATION ..................................................9

Packaging Removal ...................................................9

Rigging & Hoisting .....................................................9

Minimum Clearance Requirements .........................10

Rooftop Mounting ....................................................10

Ground Level ...........................................................10

Downﬂow to Horizontal Conversion ......................... 11

Condensate Drain ...................................................11

GAS SUPPLY & PIPING ............................................11

Leak Check .............................................................12

High Altitude Deration .............................................12

Conversion to LP/Propane ......................................13

ELECTRICAL WIRING ............................................... 14

Pre-Electrical Checklist ...........................................14

Line Voltage ............................................................. 14

Grounding................................................................14

Unbalanced 3-Phase Supply Voltage ......................15

Thermostat / Low Voltage Connections ................... 15

Blower Speed ..........................................................15

Heat Anticipator ....................................................... 16

STARTUP & ADJUSTMENTS ...................................16

Pre-Start Check List ................................................16

Startup Procedures .................................................16

Air Circulation ..........................................................17

System Cooling .......................................................17

System Heating .......................................................17

Verifying & Adjusting Temperature Rise ..................17

Verifying Burner Operation ......................................17

Verifying Operation of Over-Temperature

Limit Control ............................................................17

Verifying & Adjusting Firing Rate .............................18

Manifold Pressure Adjustment ................................18

Refrigerant Charging ...............................................18

OPERATING SEQUENCE .........................................19

Cooling Mode ..........................................................19

Blower Mode ...........................................................19

Heating Mode ..........................................................19

UNIT MAINTENANCE ................................................19

Routine Maintenance ..............................................20

Motor / Bearing Lubrication Requirements ..............20

Cleaning of Burners ................................................20

Cleaning the Heat Exchanger .................................21

Removal of Unit Top Pan .........................................21

REPLACEMENT PARTS ............................................21

COMPONENT FUNCTIONS ......................................22

TROUBLESHOOTING ...............................................22

FIGURES & TABLES .................................................23

Figure 11 - Location of Unit Components ............23

Physical Dimensions ...............................................24

Figure 12 - R6GN 150/180 Series .......................24

Table 3 - Unit Shipping Weights ...........................25

Blower Performance Data .......................................26

Table 4 - R6GN 150 Series ..................................26

Table 5 - R6GN 180 Series ..................................27

R6 Charging Charts ................................................28

Figure 13 - R6GN-150 Series ..............................28

Figure 14 - R6GN-180 Series ..............................29

Electrical Information ............................................... 30

Figure 15 - Ladder Diagram .................................30

Figure 16 - Wiring Diagram ..................................31

Table 6 - Electrical Data .......................................32

Gas Information ....................................................... 33

Table 7- Gas Flow Rates ......................................33

Table 8 - Gas Pipe Capacities .............................. 33

Table 9 - Oriﬁce or Drill Sizes for Nat. Gas ...........34

Table 10 - Oriﬁce or Drill Sizes for LP Gas ........... 34

Table 11- Heating Rise / Range ...........................34

Figure 17 - Gas Valve Label .................................35

INSTALLATION / PERFORMANCE CHECKLIST .....36

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION

Please read all instructions before servicing this equipment.

Pay attention to all safety warnings and any other special

notes highlighted in the manual. Safety markings are used

frequently throughout this manual to designate a degree

or level of seriousness and should not be ignored.

WARNING indicates a potentially hazardous situation

that if not avoided, could result in personal injury or death.

CAUTION indicates a potentially hazardous situation that

if not avoided, may result in minor or moderate injury or

property damage.

ATTENTION INSTALLERS: It is your responsibility

to know this product better than your customer. This

includes being able to install the product according to

strict safety guidelines and instructing the customer on

how to operate and maintain the equipment for the life of

the product. Safety should always be the deciding factor

when installing this product and using common sense

plays an important role as well. Pay attention to all safety

warnings and any other special notes highlighted in the

manual. Improper installation of the unit or failure to follow

safety warnings could result in serious injury, death, or

property damage. These instructions are primarily intended

to assist qualiﬁed individuals experienced in the proper

installation of this appliance. Some local codes require

licensed installation/service personnel for this type of

equipment. After completing the installation, return these

instructions to the customer’s package for future reference.

WARNING:

Improper installation, service, adjustment,

or maintenance may cause explosion, re,

electricalshockorotherhazardousconditions

whichmayresultinpersonalinjuryorproperty

damage. Unless otherwise noted in these

instructions, only factory authorized kits or

accessoriesmaybeusedwiththisproduct.

WARNING:

Donotplacecombustiblematerialonoragainst

the unit cabinet. Do not place combustible

materials, including gasoline and any other

ammablevaporsandliquids, inthevicinity

oftheunit.

WARNING:

PROPOSITION 65 WARNING: This product

contains berglass wool, a product known

to the state of California to cause cancer.

Disturbingtheinsulationofthisproductduring

installation,maintenance,orrepairwillexpose

youtoberglasswool.

• Breathingthismaterialmaycauserespiratory

irritationsormaycauselungcancer.

•Fiberglass wool may also cause eye

irritation,skinsensitization,orotherallergic

responsesinsusceptibleindividuals.

• Always wear goggles, disposable gloves,

longsleevedshirt,andappropriatebreathing

protectionwhenworkingnearthisinsulation.

Ifcontactwithskinoccurs,washimmediately

withsoapandwater.Incaseofcontactwith

eyes, ush immediately with water for at

least15minutes.Contactaphysicianifneeded.

WARNING:

The information listed below and must be

followed during the installation, service,

and operation of this unit. Unqualified

individualsshouldnotattempttointerpretthese

instructionsorinstallthisequipment.Failure

tofollowsafetyrecommendationscouldresult

inpossibledamagetotheequipment,serious

per

sonalinjuryordeath

• Thisequipmentcontainsliquidandgaseousrefrigerant

under high pressure. Installation or servicing should only

be performed by qualiﬁed trained personnel thoroughly

familiar with this type equipment.

• Before beginning the installation, verify that the unit

model is correct for the job. The unit model number

is printed on the data label. Follow all precautions in

the literature, on tags, and on labels provided with

the equipment. Read and thoroughly understand

the instructions provided with the equipment prior to

performing the installation and operational checkout

of the equipment.

• Never test for gas leaks with an open ame. Use a

commercially available soap solution to check all

connections See pages 12 - 13.

• Follow all precautions in the literature, on tags, and

on labels provided with the equipment. Read and

thoroughly understand the instructions provided with

the equipment prior to performing the installation and

operational checkout of the equipment.

• Thisunitisdesignedonlyforoutdoorinstallationsand

should be located with consideration of minimizing the

Combustion&VentilationAir

• US: National Fuel Gas Code (NFGC), Air for

Combustion and Ventilation

• CANADA: Natural Gas and Propane Installation

Codes(NSCNGPIC),VentingSystemsandAirSupply

for Appliances

DuctSystems

• US and CANADA: Air Conditioning Contractors

Association (ACCA) Manual Q, Sheet Metal and

Air Conditioning Contractors National Association

(SMACNA), or American Society of Heating,

Refrigeration, and Air Conditioning Engineers

(ASHRAE)FundamentalsHandbook

Electrical Connections

• US:NationalElectricalCode(NEC)ANSI/NFPA70

• CANADA:CanadianElectricalCodeCSAC22.1

GasPiping&GasPipePressureTesting

• US:NFGCandNationalPlumbingCodes

• CANADA:NSCNGPIC

General Installation

• US:CurrenteditionoftheNFGCandtheNFPA90B.

For copies, contact the National Fire Protection

Association Inc., Batterymarch Park, Quincy, MA

02269; or American Gas Association, 400 N. Capitol,

N.W., Washington DC 20001 or www.NFPA.org.

• CANADA:NSCNGPIC.Foracopy,contactStandard

Sales, CSA International, 178 Rexdale Boulevard,

Etobicoke(Toronto),Ontario,M9W1R3Canada

Safety

• US:(NFGC)NFPA54–1999/ANSIZ223.1andthe

Installation Standards, Warm Air Heating and Air

Conditioning Systems ANSI/NFPA 90B.

• CANADA:CAN/CGA-B149.1–and.2–M00National

StandardofCanada.(NSCNGPIC)

REQUIREMENTS & CODES

• Thisequipmentmustbeinstalledinaccordancewith

instructionsoutlinedinthismanual,allapplicable

local buildingcodes, and the current revisionof

theNationalFuelGasCode(NFPA54/ANSIZ223.1)

ortheNaturalGasandPropaneInstallationCode,

CAN/CGA B149.1.

• Allelectricalwiringmustbecompletedinaccordance

with local, state and national codes and regulations and

withtheNationalElectricCode(ANSI/NFPA70)orin

Canada the Canadian Electric Code Part 1 CSA C.22.1.

• The installer must comply with all local codes and

regulations which govern the installation of this type

of equipment. Local codes and regulations take

precedence over any recommendations contained in

these instructions. Consult local building codes and the

NationalElectricalCode(ANSICI)forspecialinstallation

requirements.

• Air Ducts must be installed in accordance with the

standards of the National Fire Protection Association

“Standards for Installation of Air Conditioning and

Ventilation Systems” (NFPA 90A), “Standard for

Installation of Residence Type Warm Air Heating and Air

ConditioningSystems”(NFPA90B),theseinstructions,

and all applicable local codes.

• ConsultTable11(page34),andtheratingplateforthe

proper circulating air ﬂow and temperature rise. It is

important that the duct system be designed to provide

the correct ﬂow rates and external pressure rise. An

improperly designed duct system can result in nuisance

shutdowns, and comfort or noise issues.

• Thisunitisdesignedforoutdoorinstallationsonlyand

should be located as described on page 10.

• Use only with the type ofgas approvedforthisunit.

Refer to the unit rating plate.

• Provideadequatecombustionandventilationairtothe

unit. See pages 6 - 7.

• Provideadequateclearancesaroundtheairventintake

terminal as speciﬁed on pages 7 - 8.

• Combustion products must be discharged outdoors.

Connect this unit to an approved vent system only, as

speciﬁed on pages 6 - 7.

• Additionalcodeslistedbelowareforreferencepurposes

only and do not necessarily have jurisdiction over

local or state codes. Local codes and regulations take

precedence over any recommendations contained in

these instructions. Always consult with local authorities

before installing any gas appliance.

length of the supply and return ducts. Consideration

should also be given to the accessibility of fuel, electric

power, service access, noise, and shade.

• Theinstallershouldbecomefamiliarwiththeunitswiring

diagram before making any electrical connections to the

unit.SeetheunitwiringlabelorFigures15&16(pages

30-31).

• Usecautionwhenhandlingthisapplianceorremoving

components. Personal injury can occur from sharp metal

edges present in all sheet metal constructed equipment.

GENERAL INFORMATION

AbouttheRooftopUnit

Single Package Gas Heating / Electric Cooling Rooftop

Units are designed only for outdoor rooftop or ground level

installations and can be readily connected to the duct

system of a building. This unit has been tested for capacity

and efﬁciency in accordance with AHRI Standards and

will provide many years of safe and dependable comfort,

providing it is properly installed and maintained. With

regular maintenance, this unit will operate satisfactorily

year after year. Abuse, improper use, and/or improper

maintenance can shorten the life of the appliance and

create unsafe hazards.

To achieve optimum performance and minimize equipment

failure, it is recommended that periodic maintenance be

performed on this unit. The ability to properly perform

maintenance on this equipment requires certain tools

and mechanical skills.

BeforeYouInstallthisEquipment

√ The cooling load of the area to be conditioned must be

calculated and a system of the proper capacity selected.

It is recommended that the area to be conditioned be

completely insulated and vapor sealed.

√ Check the electrical supply and verify the power supply

is adequate for unit operation. Consideration should be

given to availability of electric power, service access,

noise, and shade. If there is any question concerning

the power supply, contact the local power company.

√ All units are securely packed at the time of shipment and

upon arrival should be carefully inspected for damage

prior to installing the equipment at the job site. Verify

coil ﬁns are straight. If necessary, comb ﬁns to remove

attenedorbentns.Claimsfordamage(apparentor

concealed)shouldbeledimmediatelywiththecarrier.

√ Please consult your dealer for maintenance information

and availability of maintenance contracts. Read all

instructions before installing the unit.

Locating the Unit

• Surveythejobsitetodeterminethebestlocationfor

the packaged unit. The unit should be located with

consideration of minimizing the length of the supply

and return ducts. If practical, place the equipment and

its ducts in an area where they will be shaded from

the afternoon sun, when the heat load is greatest.

Consideration should also be given to the accessibility

of fuel, electric power, service access, noise, and shade.

• Selectasolid,levelposition,preferablyonaconcrete

slab, slightly above the grade level, and parallel to the

building.

• Overhead obstructions, poorly ventilated areas, and

areas subject to accumulation of debris should be

avoided. Do not place the unit in a conﬁned space or

recessed area where discharge air from the unit could

re-circulate back through the condenser coil.

• Sufcientclearanceforunobstructedairowthroughthe

louvered control access panel and outdoor coil must be

maintained in order to achieve rated performance. See

Figure5(page10)forminimum clearance requirements.

• A clearance of at least 48 inches from the blower

access panel and from the louvered burner access

panel is the required clearance to combustibles. Please

refertoFigure5(page10)forallrequirements.Where

accessibilitytocombustiblesclearancesaregreater

thanminimumclearances,accessibilityclearances

musttakepreference.

• Thehotcondenserairmustbedischargedupandaway

from the home.

• Ifpractical,placetheairconditioneranditsductsinan

area where they will be shaded from the afternoon sun,

when the heat load is greatest.

HeatingLoad

This unit should be sized to provide the design heating

load requirement. Heating load estimates can be made

using approved methods available from Air Conditioning

ContractorsofAmerica(ManualJ);AmericanSocietyof

Heating, Refrigerating, and Air Conditioning Engineers;

or other approved engineering methods. For installations

above 2,000 ft., the unit should have a sea level input

rating large enough that it will meet the heating load after

deration for altitude.

WARNING:

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for

eachapplianceconnectedtotheventingsystem

beingplacedintooperationcouldresultincarbon

monoxidepoisoningordeath.Thefollowingsteps

shallbefollowedwitheachindividualappliance

connectedtotheventingsystembeingplacedin

operation,whileallotherappliancesconnectedto

theventingsystemarenotinoperation:

1.Seal any unused openings in the venting

system.

2.Inspecttheventingsystemforpropersizeand

horizontalpitch,asrequiredintheNationalFuel

GasCode,ANSIZ223.1/NFPA 54ortheCSA

B149.1,NaturalGasandPropaneInstallation

Codesandtheseinstructions.Determinethat

there is no blockage or restriction, leakage,

corrosionandotherdeciencieswhichcould

causeanunsafecondition.

3.Asfaraspractical,closeallbuildingdoorsand

windowsandalldoorsbetweenthespacein

whichtheappliance(s)connectedtotheventing

system are located and other spaces of the

building.

4.Closereplacedampers.

5.Turn on clothes dryers and any appliance

notconnectedtotheventingsystem.Turnon

anyexhaustfans, suchasrangehoodsand

bathroomexhausts,sotheyareoperatingat

maximum speed. Do not operate a summer

exhaustfan.

6.Follow the lighting instructions. Place the

appliance being inspected into operation.

Adjustthethermostatsoapplianceisoperating

continuously.

7.Test for spillage from draft hood equipped

appliances at the draft hood relief opening

after5minutesofmainburneroperation.Use

theameofamatchorcandle.

8.Ifimproperventingisobservedduringanyof

theabovetests,theventingsystemmustbe

correctedinaccordancewiththeNationalFuel

GasCode,ANSIZ223.1/NFPA54and/orCSA

B149.1,NaturalGasandPropaneInstallation

Codes.

9.Afterithasbeendeterminedthateachappliance

connectedtotheventingsystemproperlyvents

whentestedasoutlinedabove,returndoors,

windows,exhaustfans,replacedampersand

anyothergas-redburningappliancetotheir

previousconditionsofuse.

AVERTISSEMENT:

RISQUED’EMPOISONNEMENTAU

MONOXYDE DE CARBONED

Le non-respect des consignes suivantes portant

sur chacun des appareils raccordés au système

d’évacuation mis en service pourrait entraîner

l’empoisennement au monoxyde de carbone ou

la mort. Les consignes suivantes doivent être

observéespourchaqueappareilraccordéausystème

d’évacuationmisenservicesilesautresappareils

raccordésausystèmenesontpasenservice:

1.Scellertouteouverturenonutiliséedelasystéme

d’évacuation;

2.S’assurerquelasystémed’évacuationprésente

des dimensions et une pente horizontale

conformes à la norme ANSI Z223.1/NFPA

54, intitulée National Fuel Gas Code ou aux

codes d’installation CSA-B149.1, ainsi qu’aux

présentesinstructions.S’assurerquelasystéme

d’évacuation n’est pas bloquée, restreinte,

corrodée,qu’ellenefuitpasetqu’elleneprésente

aucunautredéfautpotentiellementdangereux;

3.Danslamesuredupossible,fermertoutesles

portesetfenêtresdubâtiment,ettouteslesportes

entrelapièceoùsetrouvel’appareilraccordéà

lasystémed’évacuationetlesautrespiècesdu

bâtiment.

4.Fermerlesregistresdesfoyers;

5.Mettre en service les sécheuses et tout autre

appareil qui n’est pas raccordé à la systéme

d’évacuation.Fairefonctionneràrégimemaximal

toutventilateurd’évacuation,telqueleshottesde

cuisinièreetlesventilateursdesallesdebains.

Nepasmettreenservicelesventilateursd’été.

6.Respecterlesinstructionsd’allumage.Mettreen

servicel’appareilàl’essai.Réglerlethermostat

demanièreàcequel’appareilfonctionnesans

interruption;

7.Vérifier s’il y a débordement à l’orifice

d’évacuationducoupetiragedesappareilsdotés

d’un coupe tirage 5 minutes après l’allumage

du brûleur principal. Utiliser la amme d’une

allumetteoud’unechandelle.

8.Si l’on constate, au cours de l’un des essais

quiprécèdent, que l’évacuationestdéciente,

corrigerlesystèmed’évacuationconformément

àla norm ANSIZ223.1/NFPA 54, NationalFuel

GasCode,et(ou)auxcodesd’installationCSA

B149.1.

9.Après avoir déterminé que tous les appareils

raccordésàlasystémed’évacuationévacuent

correctement tel que prescrit ci-dessus,

rouvrirlesportesetlesfenêtresetremettreles

ventilateursd’évacuation,lesregistresdefoyers

ettoutautreappareilfonctionnantaugazàleur

étatdefonctionnementinitial.

COMBUSTION AIR & VENTING REQUIREMENTS

VentTermination

This unit has been equipped with an integral venting

system and designed to operate only with this venting

system. No additional venting shall be used. Thisunit

mustbeventedtotheoutdoors.

WARNING:

Thisunitisintendedforoutdoorinstallation

only.Donotventtheunitthroughaconventional

ventingsystem.

A vent cover assembly has been supplied with the unit

and can be found secured to the gas controls within

the control area of this unit. Figure 1 shows the proper

installation of the vent cover assembly over the vent outlet

on the exterior of the corner panel. The fasteners used to

secure the vent cover assembly have been included in

the owner’s package. Theventcoverassemblymust

beinstalledtoassureproperoperationoftheunit.

The list below summarizes the location requirements for

theventingsystemtermination:

• The location of the vent termination must be consistent

withtheNationalFuelGasCode(ANSIZ223.1)orCAN/

CGA-B149 Installation Codes.

• Must be located at least 4 feet horizontally from any

electric meters, gas meters, regulators, and relief

equipment.

• Must be located at least 3 feet above any forced air inlet

located within 10 feet of unit.

• Must be located at least 4 feet below, 4 feet horizontally

from, or 1 foot above any door, window, or gravity air

inlet into any building.

• Must be located at least 1 foot above grade and installed

in such a manner as to prevent snow accumulation from

obstructing the vent termination.

• The vent termination must not be located above any

public walkways.

Figure1.VentCoverAssembly

GeneralInformation

WARNING:

Installationmethodsotherthanthosedescribed

inthefollowingsectionsmustcomplywiththe

NationalFuelGasCodeandallapplicablelocal

codesforprovidingsufcientcombustionair

tothefurnace.

Provisions must be made during the installation of this

unit that provide an adequate supply of air for combustion.

• Instructions for determining the adequacy of an

installation can be found in the current revision of the

NFGC(ANSIZ223.1/NFPA54).Consultlocalcodes

forspecialrequirements. These requirements are for

US installations as found in the NFGC.

• TherequirementsinCanada(B149.1)arestructured

differently. Consult with B149.1 and local code ofﬁcials

for Canadian installations.

WARNING:

Combustible air must not be drawn from a

contaminatedatmosphere.Excessiveexposure

tocontaminatedcombustionairwillresultin

safetyandperformancerelatedproblems.

To maximize heat exchanger life, the combustion air

must be free of chemicals that can form corrosive acidic

compounds in the combustion gases. The recommended

source of combustion air is to use clean air from outside.

DONOTplaceanychemicalswithammableorcaustic

vaporsortheseothercorrosivechemicalsnearthe

venttermination:

• Gasoline/Kerosene

• Permanentwavesolutions

• Chlorinatedwaxesandcleaners

• Chlorinebasedswimmingpoolchemicals

• Watersofteningchemicals

• De-icingsaltsorchemicals

• Carbontetrachloride

• Halogentyperefrigerants

• Cleaningsolvents

• Cements,glues,paintremovers,varnishes,etc.

• Hydrochloricacid

• Masonryacidwashingmaterials

Air openings in the door of the unit, warm air registers, and

return air grilles must never be restricted. If the unit does

not receive an adequate supply of air for combustion, the

ﬂame roll-out control located above the burners will open,

turning off the gas supply to the burners. This safety device

is a manually reset switch. IMPORTANT NOTE!:DO NOT

installjumperwiresacrossthiscontroltodefeatits

functionorresetthecontrolwithoutidentifyingand

correctingthefaultcondition.

If this control must be replaced, use only factory authorized

replacement parts. See the Replacement Parts List on

page 21.

• Make sure that the exhaust gases will not impinge

on windows or building surfaces, which may be

compromised or damaged by condensation.

• Do not install the unit in a location where exhaust from

the vent termination will be directed into windows,

stairwells, under decks, or other recessed areas.

CIRCULATING AIR SUPPLY

WARNING:

Donotallowcombustionproductstoenterthe

returnairductworkorthecirculatingairsupply.

Failuretopreventthecirculationofcombustion

products into the living space can create

potentially hazardous conditions including

carbonmonoxidepoisoningthatcouldresult

inpersonalinjuryordeath.

Allreturnductworkmustbesecuredtotheunit

withsheetmetalscrews.Allreturnductwork

mustbeadequatelysealedandalljointsmust

betaped.Whenreturnairisprovidedthrough

thebottomoftheunit,thejointbetweenthe

unitandthereturnairplenummustbeairtight.

Theroofcurborcementpadonwhichtheunitis

mountedmustprovidesoundphysicalsupport

of the unit with nogaps,cracks, orsagging

betweentheunitandthecurborpad.

Returnairandcirculatingairductworkmustnot

beconnectedtoanyotherheatproducingdevice

suchasareplaceinsert,stove,etc.Doingso

mayresultinre,explosion,carbonmonoxide

poisoning,personalinjury,orpropertydamage.

AirDucts

This unit is designed only for use with a supply and return

duct. Air ducts should be installed in accordance with the

standards of the National Fire Protection Association

“Standard for Installation of Air Conditioning Systems”

(NFPA90A),“StandardforInstallationofResidenceType

WarmAirHeatingandAirConditioningSystems”(NFPA

90B),andallapplicablelocalcodes.NFPApublicationsare

availablebywritingto:NationalFireProtectionAssociation,

BatterymarchPark,Quincy,ME02269orvisitwww.NFPA.

org on the web.

• DesigntheductworkaccordingtoManualQbytheAir

ConditioningContractorsofAmerica(ACCA).

• Theductsmustbeproperlysizedandnotexceed0.2”

W.C. pressure drop at 400 scfm per nominal ton of

cooling capacity.

• Duct work should be attached directly to the unit ﬂanges

for horizontal applications.

• Ifroof curb is installed, the ducts must be attached to

the curb hangers, not the unit.

• It is recommended that the outlet duct be equipped

with a removable access panel. This opening should

be accessible when the unit is installed in service and

shall be of a size such that the smoke or reﬂected

light may be observed inside the casing to indicate the

presence of leaks in the heat exchanger. The cover for

the opening shall be attached in such a manner as to

prevent leaks.

• If outside air is utilized as return air to the unit for

ventilation or to improve indoor air quality, the system

must be designed so that the return air to the unit is not

lessthan50°F(10°C)duringheatingoperation.

• Ifacombinationofindoorandoutdoorairisused,the

ducts and damper system must be designed so that the

return air supply to the furnace is equal to the return air

supply under normal, indoor return air applications.

AirFilterRequirements

WARNING:

Neveroperatetheunitwithoutalterinplace.

Dust and lint could accumulate on internal

parts,resultinginlossofefciency,equipment

damageandpossiblere.

• Allreturnairmustpassthroughtheltersbeforeentering

the evaporator coil. It is important that all ﬁlters be kept

clean and replaced frequently to ensure proper operation

of unit. Dirty or clogged ﬁlters will reduce the efﬁciency

of the unit and result in unit shutdowns. Refer to Table

1 for recommended ﬁlter sizes.

• Airlterpressuredropmustnotexceed0.08inchesWC.

UNIT

FACTORY

FILTER SIZE

QTY

R6GN-150(C,D)-(180,270)C 16x20x2 8

R6GN-180(C,D)-(270,315)C 16x20x2 8

Table1.FilterSizes&Quantities

UnconditionedSpaces

All duct work passing through unconditioned space must

be properly insulated to minimize duct losses and prevent

condensation. Use insulation with an outer vapor barrier.

Refer to local codes for insulation material requirements.

AcousticalDuctWork

Certain installations may require the use of acoustical

lining inside the supply duct work.

• Acoustical insulation must be in accordance with the

current revision of the Sheet Metal and Air Conditioning

ContractorsNationalAssociation(SMACNA)application

standard for duct liners.

• Duct lining must be UL classiﬁed batts or blankets with

a ﬁre hazard classiﬁcation of FHC-25/50 or less.

• Fiber duct work may be used in place of internal duct

liners if the ﬁber duct work is in accordance with the

current revision of the SMACNA construction standard

on ﬁbrous glass ducts. Fibrous duct work and internal

acoustical lining must be NFPA Class 1 air ducts when

tested per UL Standard 181 for Class 1 ducts.

UNIT INSTALLATION

PackagingRemoval

1. Remove top crate brackets and wooden cap assembly

fromtopofunit(Figure2).

2. Remove lower crate brackets, four side skids, and

two end skids from each side of unit. NOTE: DO NOT

remove base rails from unit.

3. Removecratebrackets(Figure3)securingfourbottom

boards to underside of unit. NOTE: Some screws are

located in fork slots.

4. Remove bottom boards from beneath unit.

5. Inspect unit thoroughly for shipping damage.

6. Carefully lower and position unit to it’s permanent

location.

Rigging & Hoisting

WARNING:

Toavoidtheriskofpropertydamage,personal

injury,ordeath,itistherigger’sresponsibility

toensurethatwhatevermeansareusedtohoist

theunitaresafeandadequate:

• Theliftingequipmentmustbeadequateforthe

load.RefertoTable3(page25)forunitweights.

• Theunitmustbeliftedfromtheholesinthe

baserailsusingcablesorchains.

• Spreaderbarsarerequiredtoprotecttheunit

andensureevenloading.SeeFigure4.

• Keeptheunitinanuprightpositionatalltimes.

Theriggingmustbelocatedoutsidetheunits

centerofgravity.RefertoFigure12(page24)

forlocatingthecenterofgravity.

• All panels mustbe securely in place during

riggingandhoisting.

Figure2.SideView

Wood Cap

Assembly

Top Crate

Brackets

Lower

Crate

Brackets

End Skid

Side Skids

Figure4.Rigging&Hoisting

LIFTING

BEAM

CABLE OR

CHAIN

SPREADER

BAR

SPREADER

BAR

BASE RAIL

Figure3.BottomView

Crate

Brackets

(x6)

Bottom

Boards

(x4)

No Fork slots this end

Unit Front End

Unit Right Side

Unit Left Side

Top of unit

to be

unobstructed

Recommended Clearances

for Servicibility

Minimum Required

Clearances to Combustibles

36"

48"

36"

48"

72"

48"

Figure5.UnitClearanceRequirements

RooftopMounting

Rooftop installations must be located according to local

buildingcodesorordinancesandtheserequirements:

• The roof must be capable of handling the weight of the

unit.Forunitweights,seeTable3(page25).Reinforce

the roof if necessary.

• Theappropriateaccessoryroofcurb(Figure6)mustbe

installed prior to unit installation. The roof curb must be

square and level to ensure proper condensate drainage.

Pleasefollowallinstructionsprovidedwiththekit.

WARNING:

Neverdrillorpunchholesinunitbasewheninstalling

downowunits.Leakagemayoccurifbottompan

ispunctured

• Onbottomdischargeapplications,thesupplyandreturn

air ducts must be attached to the roof curb duct supports,

not the unit. Install all ductwork before setting unit on

curb or frame.

Figure7.ConcreteMountingPad

3” min

Horizontal

Roof Curb

Horizontal Return

Air Opening

Horizontal Supply

Air Opening

3” min

Figure6.HorizontalRoofCurb

Horizontal Return

Air Opening

Horizontal Supply

Air Opening

Horizontal

Roof Curb

MinimumClearanceRequirements

R6GN units are certiﬁed as combination heating and

cooling equipment for outdoor installation only. Figure 5

displays the minimum clearances to combustible materials

for both downﬂow and horizontal discharge.

R6GN units may be installed on wood ﬂooring or on

Class A, B, or C roof covering material when used with

bottom supply and return air ducts as long as the following

requirementsaremet:

• If using horizontal supply and return air ducts, the

horizontal roof curb kit and return air kit must be installed

prior to unit installation. Horizontal roof curb is required.

• Ifusingbottomdischargewithreturnairductsaroofcurb

must be installed prior to unit installation. See Rigging

andHoistingsection(page9)forsettingoftheunit.

• Frame support must be constructed using non-

combustible materials. Full perimeter support is required

under the unit. Supports must be made of steel or weather

resistant wooden materials. The unit must be square

and level to ensure proper condensate drainage.

• Theframemustbehighenoughtoensureprevention

of any moisture from entering the unit. Recommended

heighttounitbaseis8”(20cm)forbothDownowand

Horizontal installations.

• Secure roof curb or frame to roof using acceptable

mechanical methods per local codes.

GroundLevel

Ground level installations must be located according to

localbuildingcodesorordinancesandtheserequirements:

• Clearancesmustbeinaccordancewiththoseshown

in Figure 5.

• Aconcretemountingpad(Figure7)mustbeprovided

and separate from the building foundation. The pad

must be level to ensure proper condensate disposal

and strong enough to support the unit’s weight. The slab

heightmustbeaminimumof3”(8cm)abovegradeand

with adequate drainage.

• Unitsrequirehorizontalroofcurbandreturnairkitfor

horizontal installations.

• Ductwork should be attached directly to anges on

panels supplied in horizontal duct conversion kits.

3” Min.

2” Min.

Condensate Drain

Figure8.CondensateDrain

DownowtoHorizontalConversion

The unit is shipped ready for downﬂow duct connections. If

horizontal ducts are required, the unit must be converted

according to the directions in the conversion kit for both

the supply and return ducts.

CondensateDrain

The method for disposing of condensate varies according

to local codes. Consult your local code or authority having

jurisdiction.

Condensate is drained from the unit through one of two

3/4” (19mm) PVC female threaded ttings located on

eachsideoftheunit(Figure8).Oneinsidethebottomof

the ﬁlter access area and one at the bottom of the control

panel area. Both are accessible through the base rail

using a straight length of 3/4” pipe equipped with a 3/4”

threaded male ﬁtting. When connecting rigid drain line,

hold any ﬁttings with a wrench to prevent twisting. Do

notovertighten!

FIRE OR EXPLOSION HAZARD

•Failuretofollowsafetywarningsexactly

couldresultinseriousinjuryorproperty

damage.

•Installationandservicemustbeperformed

byaqualiedinstaller,serviceagencyor

thegassupplier.

•Donotstoreorusegasolineorother

ammablevaporsandliquidsinthe

vicinityofthisoranyotherappliance.

WHAT TO DO IF YOU SMELL GAS

•Donottrytolightanyappliance.

•Donottouchanyelectricalswitch;donot

useanyphoneinyourbuilding.

•Leavethebuildingimmediately.

•Immediatelycallyourgassupplierfrom

aneighbor’sphone.Followthegas

supplier’sinstructions.

•Ifyoucannotreachyourgassupplier,call

theredepartment.

WARNING:

RISQUED’INCENDIEOUD’EXPLOSION

• Lenon-respectdesavertissementsdesécurité

pourraitentraînerdesblessuresgraves,lamort

oudesdommagesmatériels.

• L’installationetl’entretiendoiventêtreeffectués

par un installateur qualié, un organisme de

serviceoulefournisseurdegazstaller,service

agencyorthegassupplier.

• Ne pas entreposer ni utiliser de l’essence ni

d’autresvapeursouliquidesinammablesdansle

voisinagedecetappareil,nidetoutautreappareil.

QUEFAIRES’ILYAUNEODEURDEGAZ

• Nepastenterd’allumeraucunappareil.

• Ne toucher à aucun interrupteur électrique;

n’utiliseraucuntéléphonedanslebâtiment.

• Évacuerl’immeubleimmédiatement.

• Appelerimmédiatementlefournisseurdegazen

employantletéléphoned’unvoisin.Respecterà

lalettrelesinstructionsdufournisseurdegaz.

• Si personne ne répond, appeler le service des

incendies.

AVERTISSEMENT:

GAS SUPPLY & PIPING

IMPORTANT NOTES:

• Allgaspipingmustbeinstalledincompliancewith

localcodesandutilityregulations.Intheabsence

oflocalcodesthegaslineinstallationmustcomply

withthelatesteditionoftheNationalFuelGasCode

ANSIZ223.1orCAN/CGAB149InstallationCodes.

• Some local codes require the installation of a

manualmainshut-offvalveandgroundjointunion

externaltothefurnace(Figure9,page13).Theshut-

offvalveshouldbereadilyaccessibleforservice

and/oremergencyuse.Consultthelocalutilityor

gassupplierforadditionalrequirementsregarding

placementofthemanualmaingasshut-off.

• Gaspipingmustneverruninorthroughairducts,

chimneys,gasvents,orelevatorshafts.

• Compoundsusedtosealjointsongaspipingmust

beresistanttotheactionsofLPpropanegas.

• Themaingasvalveandmainpowerdisconnectto

thefurnacemustbeproperlylabeledbytheinstaller

incaseemergencyshutdownisrequired.

• An1/8inchNPTpluggedtapmustbeinstalledin

thegaslineimmediatelyupstreamofthegassupply

connectiontothefurnaceforusewhenmeasuring

thegassupplypressure.Theplugshouldbereadily

accessibleforserviceuse.

• Adriplegshouldbeinstalledintheverticalpipe

runtotheunit(Figure9).

This unit is shipped from the factory for natural gas

operation at sea level elevation and is equipped with a

1/8orice/drillsizeateachburner.Table9(page33),lists

gas pipe capacities for standard pipe sizes as a function of

length in typical applications based on nominal pressure

drop in the line.

This unit only has right side gas entry. When connecting

the gas, provide clearance between the gas supply line

and the entry hole in the unit’s casing to avoid unwanted

noise and/or damage to the unit. A typical gas service

hookup is shown in Figure 9.

Leak Check

After the gas piping to the unit is complete, all connections

must be tested for gas leaks. This includes pipe connections

at the main gas valve, emergency shutoff valve and other

gas connectors.

The soap and water solution can be applied on each

joint or union using a small paintbrush. If any bubbling is

observed, the connection is not sealed adequately and

must be retightened. Repeat the tightening and soap

check process until bubbling ceases.

IMPORTANT NOTES!

• Ifpressuretestingthegassupplylinesatpressures

greaterthan1/2psig(14inchesWC),theunitmust

bedisconnectedfromthegassupplypipingsystem

topreventdamagetothegasvalve.

• Ifthetestpressureislessthanorequalto1/2psig

(14inchesWC),theunitmustbeisolatedfromthe

gassupplylinebyclosingthemanualshut-offvalve.

HighAltitudeDeration

High altitude application with this unit depends on the

installation altitude and the heating value of the gas. At

high altitudes, the heating value of natural gas is always

lower than the heating value at sea level.

All installations of this equipment must be made in

accordance with the National Fuel Gas Code or with local

jurisdiction codes. For installations at exactly 2,000 feet

in altitude or under, the installer does not need to derate

the heat exchanger performance. For any installation that

exceeds 2,000 feet, please use the following instructions

and example on page 13.

WARNING:

Thereductionofinputratingnecessaryforhigh

altitudeinstallationmayonlybeaccomplished

withfactorysuppliedorices.Donotattemptto

drilloutoricesintheeld.Improperlydrilled

orices may cause re, explosion, carbon

monoxidepoisoning,personalinjuryordeath.

RISQUED’INDENDIEOUD’EXPLOSION

Lenon-respectdesavertissementsdesécurité

pourraitd’entraînerdesblessuresgraves,lamort

oudesdommagesmatériels.

Ne jamais utiliser une flamme nue por

vérier la présence des fuites de gaz. Pour la

véricationdetouslesjoints,utiliserplutôtune

solution savonneuse commerciale fabriquée

spéciquementpurladétectiondesfuitesdegaz.

Unincendieouuneexplosionpeutentraînerdes

dommagesmatériels,desblessuresoulamort.

AVERTISSEMENT:

FIRE OR EXPLOSION HAZARD

Failuretofollowsafetywarningsexactlycould

resultinseriousinjuryorpropertydamage.

Nevertestforgasleakswithanopename.

Useacommerciallyavailablesoapsolution

madespecicallyforthedetectionofleaksto

checkallconnections.Areorexplosionmay

result causing property damage, personal

injuryorlossoflife.

WARNING:

Figure9.TypicalGasServiceConnection

1. All piping must comply with local codes, ordinances, and/or National Fuel Gas Codes.

2. A manual shutoff valve must be installed within 6 feet of this equipment.

3. Always include a drip leg in piping.

NOTES:

Gas Valve

Riser

3 in.

Minimum

Horizontal

Drop

Piped Gas Supply

Tubing Gas Supply

3 in.

Minimum

Horizontal

Drop

Gas Valve

3 in.

Min.

Riser

Piped Gas Supply

• Ifinstallingthisunitabove2,000feet,theinputratemust

bereduced4%per1,000feetofaltitude(Example:12%

at3,000feet,16%at4,000feet,etc).Alwaysroundup

to the next highest value of 1,000. So an installation

at 3,120 feet is derated by 16% due to rounding up to

4,000.NOTE:Thisderationisnecessarytocompensate

for low atmospheric pressure at high altitudes. Generally

this will require obtaining the gas heating value from

the local gas utility and replacing the burner oriﬁces.

• Tables9&10(page34)listthecorrectoricesizeand

high elevation conversion kit approved for this unit at

various altitudes. Use the Installation Example below

to determine the unit rating and oriﬁce size.

• Afterchangingtheorices,itisrequiredthatyoumeasure

the gas input rate by clocking the gas meter and using

the local gas heating value. See Verifying & Adjusting

theFiringRate(page16).

IMPORTANT NOTE! Observe the action of the burners

to make sure there is no yellowing, lifting or ﬂashback of

the ﬂame.

ConversiontoLP/Propane

WARNING:

The furnace was shipped from the factory

equippedtooperateonnaturalgas.Conversion

to LP/propane gas must be performed by

qualied service personnel using a factory

supplied conversion kit. Failure to use the

properconversionkitcancausere,explosion,

propertydamage,carbonmonoxidepoisoning,

personalinjury,ordeath.

INSTALLATION EXAMPLE:

Elevation: ..................................................3,890 feet

Type of Gas: .................................................. Natural

UnitModel: ................................... R6GN-150C270C

At 4,000 feet, the unit needs to be derated by 4% for

each 1,000 feet of elevation. This equates to 16% or

less than the sea level rating of 270,000 Btu/h.

1. Determineunitinputrating:

 [270kx(100-16)%]=226,800Btuh.Therequired

heating rate for 3,890 feet is 226,800 Btu/h.

2. Determineoricesize:

 FromTable9(page34),ndtheUnitModelNumber.

Follow across the row and stop at the 2,000-4,000

elevation column. For this example, the oriﬁce size

displayed is #31. Install one #31 oriﬁce in every burner

and check ﬁring rate. In this example, the ﬁring rate

must not exceed 226,800 Btu/h.

In the U.S., if installing the unit above 2,000 ft., refer to

Table10(page34)todeterminethecorrectoricesize.

When conversion is complete, verify the input rate is correct

as listed in the table. Please followthe instructions

providedwitheachkit.

• TheUnitedStatesLP/PropaneGasSeaLevelandHigh

Altitude ConversionKit is for LP/propane conversion

in the United States at altitudes between 2,000 ft. and

7,000 ft. above sea level.

• TheCanadian LP/Propane Gas SeaLevel andHigh

AltitudeConversionKitisforLP/propaneconversions

in Canada at altitudes between zero and 4,500 ft. above

sea level.

Line Voltage

• Electricalconnectionsmustbeincompliancewithall

applicable local codes and ordinances, and with the

currentrevisionoftheNationalElectricCode(ANSI/

NFPA 70). For Canadian installations the electrical

connections and grounding shall comply with the current

Canadian Electrical Code (CSA C22.1 and/or local

codes).

• Providepowersupplyfortheunitinaccordancewiththe

unit wiring diagram and the unit rating plate. The line

voltage to the unit should be supplied from a dedicated

branch circuit containing the correct fuse or circuit

breaker for the unit.

• Anelectricaldisconnectmustbelocatedwithinsight

ofandreadilyaccessibletotheunit. This switch shall

be capable of electrically de-energizing the outdoor unit.

See unit data label for proper incoming ﬁeld wiring. Any

other wiring methods must be acceptable to authority

having jurisdiction.

• Awiringdiagramislocatedontheinsidecoverofthe

control access panel of the outdoor unit. The installer

should become familiar with the wiring diagram before

making any electrical connections to the outdoor unit.

See Figures 15 & 16.

• Ifanyoftheoriginalwiressuppliedwiththeunitmust

be replaced, they must be replaced with material of the

same gauge and temperature rating.

• Connecttheline-voltageleadstotheterminalsonthe

contactor inside the control compartment.

• Useonlycopperwireforthelinevoltagepowersupply

to this unit. Use proper code agency listed conduit and

connector for connecting the supply wires. Use of rain

tight conduit is recommended.

• Unitsareshippedfromthefactorywiredfor230or460

volt operation. On 208-230V units being placed into 208

volt operation, remove the lead from the transformer

terminal marked 240V and connect it to the terminal

marked 208V.

• Overcurrentprotectionmustbeprovidedatthebranch

circuit distribution panel and sized as shown on the

unit rating label and according to the National Electric

Code and applicable local codes. NOTE: See the unit

rating plate for maximum circuit ampacity and maximum

overcurrent protection limits.

Grounding

WARNING:

Theunitcabinetmusthaveanuninterruptedor

unbrokenelectricalgroundtominimizepersonal

injuryifanelectricalfaultshouldoccur.Do not

usegaspipingasanelectricalground

This unit must be electrically grounded in accordance

with local codes or, in the absence of local codes, with

theNationalElectricalCode(ANSI/NFPA70)ortheCSA

C22.1 Electrical Code. Use the grounding lug provided in

the control box for grounding the unit.

ELECTRICALSHOCK,FIREOREXPLOSION

HAZARD

Failuretofollowsafetywarningsexactlycould

resultinseriousinjuryorpropertydamage.

Improperservicingcouldresultindangerous

operation, serious injury, death or property

damage.

• Before servicing, disconnect all electrical

powertofurnace.

• Whenservicingcontrols,labelallwiresprior

todisconnecting.Reconnectwirescorrectly.

• Verifyproperoperationafterservicing.

WARNING:

RISQUEDECHOCÉLECTRIQUE,D’INCENDIE

OUD’EXPLOSION

Le non-respect des avertissements de sécurité

pourraitentraîner

unfonctionnementdangereux

del’appareil,

desblessuresgraves,lamortou

desdommagesmatériels.

Unentreteinincorrectpourraitentraînerun

fonctionnementdangereuxdel’appareil,des

blessuresgraves,lamortoudesdommages

matériels

• Couper toute alimentation électrique au

générateurd’airchaudavantdeprodéder

auxtravauxd’entretein.

• Aumomentdel’entretiendescommandes,

étiqueteztousleslsavantdelesdébrancher.

S’assurerdelesraccordercorrectement.

•S’assurer que l’appareil fonctionne

adéquatementaprésl’entretien.

AVERTISSEMENT:

ELECTRICAL WIRING

Pre-Electrical Checklist

√ Verify that the voltage, frequency, and phase of the

supply source match the speciﬁcations on the unit rating

plate.

√ Verify that the service provided by the utility is sufﬁcient

to handle the additional load imposed by this equipment.

SeeTable6(page32)ortheunitwiringlabelforproper

high and low voltage wiring.

√ Verify factory wiring is in accordance with the unit wiring

diagram(Figures15&16,pages30&31).Inspectfor

loose connections.

√ For 3 phase units always check the phase balance

(page15).

Example:

AB=451V

BC=460V

AC=453V

2. Determine the average voltage in the power supply.

3.Determinethemaximumdeviation:

4. Determine percent of voltage

imbalance by using the results

from steps 2 & 3 in the following

equation.

maxvoltage deviation

fromaverage voltage

=100 x

averagevoltage

% Voltage Imbalance

454

100

=1.32%

Example:

1. Measure the line voltages

of your 3-phase power

supply where it enters the

building and at a location

that will only be dedicated

totheunitinstallation(at

the units circuit protection

ordisconnect).

Unbalanced3-PhaseSupplyVoltage

Voltage unbalance occurs when the voltages of all phases

of a 3-phase power supply are no longer equal. This

unbalance reduces motor efﬁciency and performance.

Someunderlyingcausesofvoltageunbalancemayinclude:

Lack of symmetry in transmission lines, large single-phase

loads, and unbalanced or overloaded transformers. A

motor should never be operated when a phase imbalance

in supply is greater than 2%. Perform the following steps

todeterminethepercentageofvoltageimbalance:

In this example, the measured line voltages were

451, 460, and 453. The average would be 454 volts

(451+460+453=1,364/3=454).

Theamountofphaseimbalance(1.32%)issatisfactory

since the amount is lower than the maximum allowable

2%. Please contact your local electric utility company if

your voltage imbalance is more than 2%.

Example:

Fromthevaluesgiveninstep1,theBCvoltage(460V)

isthegreatestdifferenceinvaluefromtheaverage:

460-454=6

454-451=3

454-453=1

Highest Value

• A two-stage heating/cooling thermostat is required

for R6GN series units. Select a thermostat which

operates in conjunction with the installed accessories.

The thermostat should be mounted about 5 feet above

the ﬂoor on an inside wall. See Figure 10 for proper

wire gauge and their recommended lengths for typical

thermostat connections.

• The low voltage wires must be properly connected

to the units low voltage terminal block. Route 24V

control wires through the gas furnace side of the unit.

Recommended wire gauge and wire lengths for typical

thermostat connections are shown in Figure 10.

• Thethermostatshouldbemountedabout5feetabovethe

ﬂoor on an inside wall. DO NOT install the thermostat on

an outside wall or any other location where its operation

may be adversely affected by radiant heat from ﬁreplaces,

sunlight, or lighting ﬁxtures, and convective heat from

warm air registers or electrical appliances. Refer to the

thermostat manufacturer’s instruction sheet for detailed

mounting information.

Thermostat/LowVoltageConnections

• SinglePackageGasHeating/ElectricCoolingRooftop

Units are designed to operate with a 24 VAC Class II

control circuit. The control circuit wiring must comply

with the current provisions of the NEC (ANSI/NFPA

70)andwithapplicablelocalcodeshavingjurisdiction.

Thermostat connections should be made in accordance

with the instructions supplied with the thermostat and

the indoor equipment.

Figure10.Typical2-StageHeat/Cool

ThermostatConnection

Indoor

Thermostat

Sub-Base

Unit Low Voltage

Terminal

Economizer

OCC/UNOCC

T-Stat Wire

Gauge

RecommendedT-StatWire

Length-Ft.(UnittoT-Stat)

18 Ga. 0 - 60

16 Ga. 61 - 130

Field Supplied Wiring - - - - - Use Solid Class II Copper Wire

BlowerSpeed

The blower speed is preset at the factory but must

be veriﬁed at each installation. For optimum system

performance and comfort, it may be necessary to change

the factory set speed. Refer to the Blower Performance

Data(Tables5&6,pages26&27)forproperoperating

range. Always inspect variable pitch sheaves for proper

tightness and set screws

CAUTION:

Toavoidpersonalinjuryorpropertydamage,

makesurethemotorleadsdonotmakecontact

withanyuninsulatedmetalcomponentsofthe

unit.

STARTUP & ADJUSTMENTS

Pre-Start Check List

√ Verify unit is properly supported.

√ Verify unit is level for proper condensate drainage.

√ Verify all clearance requirements are met. Airﬂow to

and from the outdoor coil must be unrestricted.

√ Verify the ductwork is adequately sealed to prevent air

leakage. Insulate if necessary.

√ Verify the line voltage power leads are securely

connected and the unit is properly grounded.

√ Verify low voltage wires are securely connected to the

correct leads in the control box.

√ Verify gas line pressure. For natural gas, the line pressure

mustnotexceed10.0inchesWC(0.36psig),orbeless

than5.5inchesWC(0.20psig).ForLPgas,theline

pressuremustnotexceed14inchesWC(0.51psig)

andmustnotbelessthan11.0inchesWC(0.40psig).

√ Verify the ﬂame roll-out control is closed.

IMPORTANT NOTE! This safety device is a manually

reset switch. If necessary, press the red button to reset

the control. DO NOT install a jumper wire across the

control to defeat its function. If the control reopens upon

start-up, DO NOT reset the control without identifying

and correcting the fault condition which caused the

control to trip.

√ Verify the gas line has been purged and all connections

are adequately sealed. To check for gas leakage, see

Leak Check section on page 12.

√ Verify the indoor blower is properly set for the installation.

√ Verify the outdoor fan turns freely.

√ Verify the power supply branch circuit overcurrent

protection is properly sized.

√ Verify all exterior panels have been reinstalled and

securely fastened.

√ Verify the thermostat is wired correctly and preset for

initial operation. Set the thermostat system switch to

OFF and the fan switch to AUTO.

StartupProcedures

WARNING:

Thisunitisequippedwithcrankcaseheaters.

Allow 24 hrs for heating of the refrigerant

compressor crankcase prior to start up and

anytimethepowerhasbeenremovedformore

than12 hrs. Failureto complymayresult in

damage or cause premature failure of the

system.

• Checkall electricalwiring forloose connectionsand

tighten as required.

• Checkunitforreturnairltersandcondensatetrap.

• Closeallelectricaldisconnectstoenergizethesystem.

Tochangetheblowerspeed:

1. Disconnect all electrical power to the unit.

2. Open the motor access panel.

3. Loosen the 4 motor mounting nuts. Turn the belt

tensioning nut until belt can be removed from the sheave

or pulley.

4. Loosen front set screw on the motor sheave.

NOTE:Turningthesetscrewclockwise(close)increases

theblowerspeed,orcounterclockwise(open)decreases

blower speed.

5. Replace belt on pulleys and position motor mounting

platetocorrectpositionforproperbelttension.Note:

Make sure the pulley, belt, and motor sheave are properly

aligned.

6. Tighten the four motor mounting nuts. Verify the drive

belt is secure and tensioned properly.

Heat Anticipator

Verify if the thermostat being used for the installation has a

heat anticipator setting. This function allows the thermostat

to anticipate the space heating rate and time the burner

to shutoff accordingly. Always refer to the thermostat

manufacturers instructions for the correct settings.

AirCirculation

1. Set the thermostat switch to OFF and the fan switch to

ON.

2. Verify the blower motor runs continuously. Check for

airdeliveryattheregister(s).Ensurethatthereareno

obstructions at the registers or in the ductwork.

3. Set thermostat fan switch to AUTO and verify the blower

shuts down immediately.

NOTE: If blower is turning opposite of arrow direction, shut

off main power to the unit and switch any two ﬁeld wires

at the disconnect. DO NOT alter unit wiring.

SystemCooling

1. Set the thermostat system switch to COOL and the fan

switch to AUTO.

2. Lower the thermostat temperature switch below

room temperature and observe that the blower, both

compressors and fans energize.

3. Verify blower is turning in direction indicated by arrow

and air discharged at the register is cooler than room

temperature.

4. Verify HI & LO refrigerant pressures.

NOTE: If refrigerant pressures are abnormal and blower

is rotating in the opposite direction of the arrow, shut off

main power to the unit and switch any two ﬁeld wires at

the disconnect. Ensure proper rotation of the blower. DO

NOT alter unit wiring. Listen for any unusual noises. Locate

the source and correct as needed.

5. Allow the unit to run for several minutes. Set the

temperature selector above room temperature and

verify that the fan, blower, and compressors cycle off

with the thermostat.

System Heating

1. Set the thermostat to the lowest setting.

2. Follow the startup procedures on this page or the

operating instruction label inside the louvered control

access panel.

3. Set the thermostat above room temperature and verify

theOperatingSequence(page19).

4. Verify that the compressor and outdoor fan motor are

not energized.

5. Run the unit and after approximately ﬁve minutes, set the

thermostat below room temperature. Verify the shutdown

sequence(steps7-8oftheOperatingSequence).

Verifying&AdjustingTemperatureRise

Verify the temperature rise through the unit is within the

range speciﬁed on the unit data label. Temperature rises

outside the speciﬁed range could result in premature heat

exchanger failure.

1. Place thermometers in the return and supply air stream

as close to the unit as possible. The thermometer on the

supply air side must be shielded against direct radiation

from the heat exchanger to avoid false readings.

2. Adjust all registers and duct dampers to the desired

position. Run the unit for 10 to 15 minutes before

taking any temperature readings. The temperature

rise is the difference between the supply and return

air temperatures.

NOTE: For typical duct systems, the temperature rise will

fallwithintherangespeciedonthedatalabel(withthe

blowerspeedatthefactoryrecommendedsetting)shown

in Table 11, page 34. If the measured temperature rise falls

outside the speciﬁed range, it may be necessary to change

the blower speed. Lowering the blower speed increases

the temperature rise and a higher speed decreases the

temperature rise.

The unit is equipped with a belt driven blower and variable

pitch motor sheave. The selection of a sheave setting

should be based on the desired CFM and the duct system

parameters.RefertotheACCA’sManualQforacomplete

description of how to determine these parameters and

Manual N for determination of the commercial load

requirements. The blower performance data can be found

inTables4&5(pages26&27).

The integrated control is designed to start the circulating

air blower approximately 40 seconds after the gas valve

opens and turn the blower motor off approximately 150

seconds after the gas valve is closed.

VerifyingBurnerOperation

WARNING:

Uninsulatedlivecomponentsareexposedwhen

thelouveredcontrolaccesspanelisremoved.

1. Remove the louvered control access panel to ensure

there is power to the unit.

2. Set the thermostat above room temperature and observe

the ignition sequence. The burner ﬂame should carry

over immediately between all burners and should extend

from each burner without lifting off, curling, or ﬂoating.

The ﬂames should be blue, without yellow tips.

3. After verifying ﬂame characteristics, set the thermostat

below room temperature and verify that the burner ﬂame

extinguishes completely.

VerifyingOperationofOver-Temperature

LimitControl

To verify operation of the over-temperature limit control,

make sure the louvered control access panel is in place

and that there is power to the unit.

1. Block the return airﬂow to the unit by installing a close-

off plate in place of or upstream of the ﬁlter.

2. Set the thermostat above room temperature and verify

the unit operates with the correct sequence of operation,

See Operating Sequence on page 19.

NOTE: The over-temperature limit control should function

to turn off the gas valve within approximately four minutes

(exacttimedependsontheefciencyoftheclose-offwhen

blockingthereturnair).Thecirculatingairandcombustion

blowers should continue to run when the over-temperature

limit control switch opens.

3. Remove the close-off plate immediately after the over-

temperature limit control opens. If the unit operates

for more than four minutes with no return air, set the

thermostat below room temperature, shut off power to

the unit, and replace the over-temperature limit control.

NOTE: On some low static/high airﬂow applications, the

Over-Temperature limit control may not function. To ensure

the limit is functioning properly, the outlet may also have to

be slightly restricted to achieve higher outlet temperatures.

Verifying&AdjustingFiringRate

The ﬁring rate must be veriﬁed for each installation to

prevent over-ﬁring of the unit.

CAUTION:

Donotre-drilltheburnerorices.Iftheorice

sizemustbechanged,useonlyneworices.

IMPORTANT NOTE: The ﬁring rate must not exceed the

rate shown on the unit data label. At altitudes above 2,000

ft., it must not exceed that on the data label less 4% for

each 1,000 ft.

Followthestepsbelowtodeterminetheunitringrate:

• Forinstallationsat2,000feetandless,theringrateis

the same as shown on the unit rating label.

• Forinstallationsabove2,000feet,computethecorrect

ﬁring rate as shown in the example on page 13.

1. Obtain the gas heating value from the gas supplier

(HHV).

2. Shut off all other gas ﬁred appliances.

3. Start the unit in heating mode and allow it to run for at

least three minutes.

4.Measure the time (in seconds) required for the gas

meter to complete one revolution.

5. Convert the time per revolution to cubic feet of gas per

hourusingTable7(page33).

6. Multiply the gas ﬂow rate in cubic feet per hour by the

heating value of the gas in Btu per cubic foot to obtain

theringrateinBtuperhour.Seeexample:

ManifoldPressureAdjustment

The manifold pressure must be set to the appropriate

valueforyourinstallation.Toadjustthemanifoldpressure:

1. Obtain the required manifold pressure setting. Refer to

either Table 9 for natural gas or Table 10 for LP/propane

gas(page34).NOTE: The values listed in the tables

are based on sea level values. At higher altitudes, the

heating value of gas is lower than the sea level heating

value.

2. Remove the regulator cap. Turn the high fire

adjusting screw clockwise to increase the pressure or

counterclockwise to reduce the pressure.

3. Replace the regulator cap after adjustments are

complete.

Refrigerant Charging

WARNING:

Ifrepairsmakeitnecessaryforevacuationand

charging,itshouldonlybedonebyqualied,

trainedpersonnelthoroughlyfamiliarwiththis

equipment.Somelocalcodesrequirelicensed

installation/service personnel to service this

type of equipment. Under no circumstances

should the owner attempt to install and/or

servicethisequipment.

Failuretocomplywiththiswarningcouldresult

inpropertydamage,personalinjury,ordeath.

This Single Package Gas Heating / Electric Cooling unit

is fully charged at the factory and requires no charging

when installed accordingly. Units should be operating

with liquid sub-cooling readings between 13° F - 15° F.

If measurements indicate a lower or higher sub-cooling

reading, refrigerant levels must be adjusted to achieve

maximum system performance. The refrigerant charge

can be checked and adjusted through the service ports

located behind the service panel. Use only gauge lines

which have a “Schrader” depression device to actuate

the valve.

Refrigerant charging charts for 12.5 and 15 ton units

are included in these instructions. To identify proper unit

chargeoperationseeFigure13(page28)for12.5tonor

Figure14(page29)for15ton.NOTE: Both refrigeration

stages must be operating when taking liquid temperature

and pressure measurements.

Refrigerant charging must be done by qualiﬁed personnel

familiar with safe and environmentally responsible

refrigerant handling procedures. See Unit Rating Plate

for proper amount of refrigerant.

Example:

• Timefor1revolutionofagasmeterwitha1cubic

footdial=40seconds.

• FromTable7,read90cubicfeetgasperhour.

• Localheatingvalueofthegas(obtainedfromgas

supplier)=1,040Btupercubicfoot.

• Inputrate=1,040x90=93,600Btuh.

7. Adjustments to the ﬁring rate can be made by adjusting

the gas manifold pressure. See the High Altitude Deration

section (pages 12 - 13) for additional information of

ﬁring rate at elevations above 2000 ft.

UNIT MAINTENANCE

OPERATING SEQUENCE

The operating sequences for the heating, cooling, and

fan modes are described below. Refer to the wiring

diagrams(Figures15&16,pages30&31).

CoolingMode

1. On a call for cooling the thermostat closes, applying 24

VAC to Y1, G, & Y2 if Stage 2 cooling is calling.

2. G applies 24VAC to the main circulating blower circuit.

3. Y1 & Y2 apply 24VAC through all safety switches before

energizing their respective contactors.

4. When the thermostat is satisﬁed the contactors are

de-energized.

5. The circulating blower motor de-energizes immediately.

BlowerMode

1. On a call for fan operation, the thermostat applies 24

VAC directly to the blower contactor.

2. The circulating blower is energized immediately.

HeatingMode

1. On a call for heat, the thermostat closes, applying 24

VAC to the W1terminal(andW2 terminal if Stage 2

heatisrequired).

2. The integrated control monitors the safety circuit at all

times. If either the roll-out switch or the over-temperature

limit controls open, the gas valve will not energize.

The main blower continues to operate until the over-

temperature limits close, the ﬂame roll-out switch is

manually reset, or the thermostat is satisﬁed.

3. The integrated control checks all safety switches at

the beginning of each heating cycle. If closed, the

combustion blower performs a 15 second pre-purge.

4. The integrated control will then supply power to the

direct spark ignitor and immediately energizes the gas

valve. NOTE: Burner operation begins in high ﬁre mode

with both Stage 1 and Stage 2 gas valve energized,

independent of the thermostat call for Stage 2 heat. If

after 30 seconds of operation with no call for Stage 2

heat, the integrated control will resume heating operation

in low ﬁre mode of operation and Stage 2 gas valve is

de-energized.

5. The ﬂame must be proven through the ﬂame sensor in

7 seconds to hold the gas valve open. The integrated

control will monitor the gas ﬂame with the ﬂame sensor

for the entire time the gas valve is open. If for any reason

the gas ﬂame drops out, the gas valve will immediately

close. After 30 second purge, the integrated control will

try to ignite 14 more times.

6. The main air blower will start and continue to run 40

seconds after the gas valve opens.

7. When the thermostat is satisﬁed, the integrated

control is de-energized. The gas valve and combustion

blower de-energize immediately while the main air

blower continues to run through the blower off delay

of approximately 150 seconds.

8. If the unit fails to prove ﬂame after ﬁfteen ignition

attempts, it will go into a soft lockout. The unit will re-

ELECTRICALSHOCK,FIREOREXPLOSION

HAZARD

Failuretofollowsafetywarningsexactlycould

resultinseriousinjuryorpropertydamage.

Improperservicingcouldresultindangerous

operation, serious injury, death or property

damage.

• Before servicing, disconnect all electrical

powertofurnace.

• Whenservicingcontrols,labelallwiresprior

todisconnecting.Reconnectwirescorrectly.

• Verifyproperoperationafterservicing.”

WARNING:

RISQUEDECHOCÉLECTRIQUE,D’INCENDIE

OUD’EXPLOSION

Le non-respect des avertissements de sécurité

pourraitentraîner

unfonctionnementdangereux

del’appareil,

desblessuresgraves,lamortou

desdommagesmatériels.

Unentreteinincorrectpourraitentraînerun

fonctionnementdangereuxdel’appareil,des

blessuresgraves,lamortoudesdommages

matériels

• Couper toute alimentation électrique au

générateurd’airchaudavantdeprodéder

auxtravauxd’entretein.

• Aumomentdel’entretiendescommandes,

étiqueteztousleslsavantdelesdébrancher.

S’assurerdelesraccordercorrectement.

•S’assurer que l’appareil fonctionne

adéquatementaprésl’entretien.

AVERTISSEMENT:

NOTE: These maintenance instructions are primarily

intended to assist qualiﬁed technicians experienced in

the proper maintenance and operation of this appliance.

To achieve optimum performance from the air conditioner

and minimize equipment failure, it is recommended that

annual maintenance be performed on this unit. The ability to

properly perform maintenance on this equipment requires

certain mechanical skills and tools.

attempt the start-up procedure every hour until the

thermostat is satisﬁed or 24 VAC power is removed

from the unit for a minimum period of 5 seconds.

NOTE: For a complete list of heating operation fault

codes, seeTroubleshooting (page 22) or Figure 15

(pg30)

RoutineMaintenance

Please consult your dealer for maintenance information

and availability of maintenance contracts.At a minimum,

routinemaintenanceshouldincludethefollowingitems:

WARNING:

Neveroperatetheunitwithoutltersinplace.

Dust and lint in the return air can build up

on internal components, resulting in loss of

efciency,equipmentdamage,andpossiblere.

• Inspectthecondensatedrainandoutdoorcoilatthe

beginning of each cooling season. Remove any debris.

Clean the outdoor coil and louvers as necessary using

a mild detergent and water. Rinse thoroughly with water.

• Theblowercompartmentshouldbecleanedmonthly

during the heating and cooling seasons to remove any dirt

and lint that may have accumulated in the compartment

or on the blower and motor. Buildup of dirt and lint on

the blower and motor can create excessive loads on

the motor resulting in higher than normal operating

temperatures and possible shortened service life.

• Itisrecommendedthattheairltersbeinspectedand

cleaned or replaced every 3 to 4 weeks using ﬁlters of

likesizeandkind.Table1(page8)liststhecorrectlter

sizes and quantities for each unit.

• Inspecttheelectricalconnectionsfortightnessatthe

beginning of each heating and cooling season.

• Inspectandcleanthescreenoftheventcoverassembly

at the beginning of each heating and cooling season.

WARNING:

Holesintheheatexchangercancauseproducts

ofcombustiontoenterthestructure.Replace

theheatexchangerifleaksarefound.Failure

topreventproductsofcombustionfrombeing

circulatedintotheoccupiedspacecancreate

potentially hazardous conditions including

carbonmonoxidepoisoningthatcouldresult

inpersonalinjuryordeath.

• Maintainheat exchanger and burners. The unit should

operate for many years without excessive scale buildup

in the heat exchanger, however, the heat exchanger, the

vent system, and the burners should be inspected and

cleaned(ifrequired)byaqualiedservicemanannually

to ensure continued safe operation. Particular attention

must be given to identify deterioration from corrosion

or other sources.

Motor/BearingLubricationRequirements

• Theblowerassemblyinthisunitisequippedwiththree

support bearings and one pillow block drive bearing. The

support bearings are sealed cartridge units and require

no further lubrication. The drive bearing is equipped for

futurelubrication(eldsuppliedttingrequired)since

it is capable of more severe duty. The drive bearing

should be checked annually for lubrication requirements

based on application and operating conditions or as

maintenance experience dictates. Extreme care is

important to prevent overﬁlling or introduction of dirt

into the bearing.

• Theindoorblowermotorispre-lubricatedatthefactory

and does not require additional lubrication under normal

application of this equipment. The motor is equipped with

grease ﬁttings if you chose to re-lubricate the bearings

based on abnormal conditions or applications. Refer to

the motor manufacturers Installation, Operation, and

Maintenance Instructions supplied in the owners packet

for suggested amounts and type based on the bearing

model number listed on the motor nameplate.

• Thecombustionairblowermotorandoutdoorfanmotors

are equipped with pre-lubricated sealed ball bearings.

No further oiling is required for the life of this product.

CleaningtheBurners

It is recommended that the burners be inspected and

cleanedannually(ifrequired)byaqualiedtechnicianto

ensure continued safe operation. Particular attention must

be given to identify deterioration from corrosion or other

sources.Iftheburnersmustbecleaned,followthesesteps:

1. Shut off the gas supply to the unit either at the meter

or at a manual valve in the supply piping.

IMPORTANT NOTE! See gas valve label on the unit or

Figure17(page35)forpropergasshutdowninstructions.

2. Turn off all power to the unit and set the thermostat to

the lowest temperature setting.

3. Remove the louvered access panel from the unit.

4. Turn the gas control knob to the “OFF” position.

CAUTION:

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improperanddangerousoperation.

5. Disconnect the wires from the gas valve, ignitor, ﬂame

sensor, and rollout switch.

6. Using two wrenches, separate the ground-joint union

in the gas supply piping at the unit.

7. Remove the piping between the gas valve and the

ground-joint union.

8. Remove four screws securing the burner assembly to

the unit.

9. Carefully remove the burner assembly from the unit.

DO NOT DAMAGE THE IGNITOR WHILE REMOVING

THE BURNER ASSEMBLY.

10. Inspect the burners for accumulated dust or debris.

If necessary, carefully clean them with a soft wire

brush and/or the nozzle of a vacuum cleaner. DO

NOT DAMAGE THE IGNITOR OR FLAME SENSOR

WHILE CLEANING THE BURNER.

11. Replace all the parts in reverse order from which they

were removed.

La page charge ...

Reznor R6GN Guide d'installation

Marque: Reznor

Modèle: R6GN

Taper: Guide d'installation

Ce manuel convient également à

R6GN 12.5 - 15 Ton

Télécharger le PDF

rapport

dans d''autres langues

English: Reznor R6GN Installation guide

Reznor R6GN Guide d'installation

Ce manuel convient également à

Reznor R6GN Guide d'installation

dans d''autres langues

Documents connexes

Autres documents