Westinghouse R6GE Manuel utilisateur

Marque: Westinghouse

Modèle: R6GE

Taper: Manuel utilisateur

Ce manuel convient également à

DF6SF

IMPORTANT! Please read all information in this manual thoroughly and become familiar with the capabilities and

use of your appliance before attempting to operate or maintain this unit. Keep this literature where you have easy

access to it in the future. If a problem occurs, check the instructions and follow recommendations given. If these

suggestions don’t eliminate your problem, call your servicing contractor. Do not attempt to service this unit yourself!

Under no circumstances should the appliance owner attempt to install and/or service this equipment. Some local

codes require licensed installation / service personnel for this type of equipment. Improper service, adjustment, or

maintenance may cause explosion, ﬁ re, electrical shock or other hazardous conditions which may result in personal

injury or property damage.

Single Package Gas Heating / Electric Cooling Unit

USER’S MANUAL

13 SEER MODELS

DO NOT DESTROY. PLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a

neighbors phone. Follow the gas suppliers

instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

WARNING:

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly

could result in serious injury or property

damage.

• Installation and service must be performed

by a qualiﬁ ed installer, service agency or the

gas supplier.

• Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

GENERAL INFORMATION

This gas heating / electric cooling unit has been

designed and built to provide many years of safe and

dependable comfort, providing it is properly installed

and maintained. With regular maintenance, this unit will

operate satisfactorily year after year. Abuse, improper

use, and/or improper maintenance can shorten the life

of the appliance and create unsafe hazards. A regular

service and maintenance schedule should be established

to ensure efﬁ cient and safe operation of the unit. See

System Maintenance on pages 3 - 4.

To achieve optimum performance and minimize equipment

failure, it is recommended that periodic maintenance be

performed on this unit. The ability to properly perform

maintenance on this equipment requires certain

mechanical skills and tools. Please consult your dealer for

maintenance information and availability of maintenance

contracts.

WARNING:

To avoid possible equipment damage, ﬁ re,

or death, the following instructions must be

observed regarding unit location, combustion

air requirements, and operational procedures.

Gas Heating / Electric Cooling Unit Location

The area around the gas heating/electric cooling unit

and the vicinity of any other gas appliances must be kept

clear and free of combustible materials, gasoline, and

other ﬂ ammable vapors and liquids. Do not store or use

ﬂ ammable items such as paint, varnish, or strippers in

the vicinity of the unit.

Do not use the area around the unit as a storage area. This

area must be kept clean and clear of loose or exposed

insulation materials. Examine the unit’s area when it is

installed or when insulation is added, since some insulation

materials may be combustible.

Do not use this appliance if any part has been under water.

Immediately call a qualiﬁ ed service technician to inspect

the unit and to replace any part of the control system and

any gas control which has been under water.

Familiarize yourself with the controls that shut off the

gas and electrical power to the unit. If the unit is to be

shut down for an extended period of time, turn off both

the gas and electrical power. For your safety always turn

off both the gas and electrical power before performing

service or maintenance on the furnace. If the gas supply

to the unit must be shut off, refer to the gas valve label

(Figure 3, page 5).

Combustion Air Supply

The gas heating/electric cooling unit needs an adequate

supply of combustion and ventilation air for proper and safe

operation. Do not block or obstruct air openings on the unit

or air openings supplying the area where it is installed.

If the unit is operated with inadequate combustion air

supply, the ﬂ ame roll-out control switch located above

the burners will open, turning off the gas supply to the

burners. The ﬂ ame roll-out control is a manual reset

device. Do not attempt to reset this device yourself! Call

your servicing contractor.

WARNING:

Combustion air must not be drawn from a

corrosive atmosphere.

To maximize heat exchanger life, the combustion air

must be free of chemicals which form corrosive acidic

compounds in the combustion gases.

IMPORTANT NOTE: Do not store any chemicals with

ﬂ ammable or caustic vapors near the vent termination.

Some examples of these chemicals are:

• Gasoline/Kerosene

• Permanent wave solutions

• Chlorinated waxes and cleaners

• Chlorine based swimming pool chemicals

• Water softening chemicals

• De-icing salts or chemicals

• Carbon tetrachloride

• Halogen type refrigerants

• Cleaning solvents

• Cements, glues, paint removers, varnishes, etc.

• Hydrochloric acid

• Masonry acid washing materials

• Plumbing Stack

Ductwork

WARNING:

Failure to prevent products of combustion

from being circulated into the occupied space

can create potentially hazardous conditions

including carbon monoxide poisoning that

could result in personal injury or death.

The duct connections must be physically sound and sealed

to the unit’s casing to prevent products of combustion from

entering the occupied space.

The return air and circulating air ductwork must not be

connected to any other heat producing device such as

a ﬁ replace insert, stove, etc. Doing so may result in ﬁ re,

explosion, personal injury, carbon monoxide poisoning,

or property damage.

OPERATING INSTRUCTIONS

Thermostat styles vary. Some models may not include the

AUTO mode and others will have the AUTO in place of the

HEAT and COOL. Others may include all three. Please

refer to the thermostat manufacturer’s User manual for

detailed programming instructions.

The thermostat should be mounted about 5 feet above the

ﬂ oor on an inside wall and not on an outside wall or other

location where its operation may be adversely affected by

radiant heat from ﬁ replaces, sunlight, or lighting ﬁ xtures,

and convective heat from warm air registers or electrical

appliances.

Cooling Operation (1 or 2-Stage Operation)

1. Set the thermostat system mode to COOL and the

thermostat fan mode to AUTO. See Figure 1.

2. Set the thermostat temperature selector to the desired

temperature level. The outdoor fan, compressor, and

indoor blower will all cycle on and off to maintain the

indoor temperature at the desired cooling level.

NOTE: If the temperature level is re-adjusted, or the

system mode is reset, the fan and compressor in the

outdoor unit may not start immediately. A protective

timer circuit holds the compressor and the outdoor fan

off for approximately 5 minutes following a previous

operation or the interruption of the main electrical

power.

Heating Operation (2 Stage)

1. Set the thermostat system mode to Heat and the

thermostat fan mode to AUTO. See Figure 1.

2. Set the thermostat temperature selector to the

desired temperature level. The indoor blower and

gas heat module will cycle on and off to maintain

the indoor temperature at the desired heating level.

NOTE: On some units there is a factory set 3 minute

time delay between Stage 1 and Stage 2 heat when

Stage 2 heating is required. See Unit wiring diagram

label.

WARNING:

If overheating occurs, or the gas supply fails to

shut off, shut off the gas valve to the unit before

shutting off the electrical supply.

NOTE: This unit is equipped with a manual-reset ﬂ ame

roll-out limit switch. This switch acts to verify that the

burner ﬂ ame is being drawn into the heat exchanger

tubes. If the ﬂ ame is not being drawn into the tubes, the

ﬂ ame roll-out switch will open within several seconds.

When this switch opens, the gas valve will de-energize

to stop the ﬂ ow of gas. The combustion inducer will stay

energized and continue to operate until the thermostat is

satisﬁ ed or the switch is closed. Do not reset the ﬂ ame

roll-out switch before identifying and correcting the fault

condition that caused the switch to open. If the switch

will not reset or continues to open, immediately contact

a qualiﬁ ed serviceman to identify and repair the problem.

System Shutdown

Set the thermostat system mode to OFF and the thermostat

fan mode to AUTO. See Figure 1. NOTE: The system will

not operate, regardless of the thermostat temperature

selector’s setting.

Operating the Indoor Blower Continuously

Set the thermostat fan mode to ON (or CONT on some

thermostat models). See Figure 1.

The indoor blower will start immediately, and will run

continually until the fan switch is reset to AUTO.

The continuous indoor blower operation can be obtained

with the thermostat system switch set in any position,

including OFF.

The continuous indoor blower operation is typically used to

circulate the indoor air to equalize a temperature imbalance

due to a solar load, cooking, or ﬁ replace operation.

SYSTEM MAINTENANCE

CAUTION:

Verify all electrical power to the unit is

disconnected and the gas is shut off before

performing the following recommended

maintenance.

Proper maintenance is most important to achieve the best

performance from the appliance and should be performed

by a qualiﬁ ed service technician at least once a year.

Follow the maintenance schedule and the instructions

below for years of safe, trouble free operation.

• Do not place combustible materials on or against the

cabinet.

• Do not store gasoline or any other ﬂ ammable vapors

and liquids in the vicinity of the unit.

• Annually inspect the physical support of the unit to

ensure that it is physically sound without sagging,

Figure 1. Digital Thermostat

Fan

Mode

Temperature

Selector

System

Mode

cracks, gaps, etc., around the base so as to provide a

seal between the support and the base.

• Annually inspect the return-air connection to ensure

that it is physically sound and is still sealed to the

casing of the unit. Also inspect the unit, ductwork, and

vent system for signs of physical deterioration.

• Always replace the doors on the unit after servicing.

Do not operate the unit without all doors and covers

in place. Avoid operating the unit when windows and

doors are open.

• Refer to the Maintenance Schedule (Table 1, page 8)

for recommended maintenance information.

CAUTION:

DO NOT come into contact with any of the

internal electrical components while cleaning

the unit.

Regular Cleaning

• Remove any leaves and grass clippings from the

outdoor coil. IMPORTANT: Be careful not to damage

the aluminum ﬁ ns.

• Check for and remove any obstructions such as twigs,

sticks, etc.

• Clean the blower compartment regularly during the

heating and cooling seasons to remove any dust

that may have accumulated in the compartment or on

the blower and motor. Buildup of dust on the blower

and motor can create excessive loads on the motor

resulting in higher than normal operating temperatures

and possible shortened service life.

Air Filters

WARNING:

Never operate the unit without a ﬁ lter in the

return air system. Dust and lint in the return

air can build up on the internal components,

resulting in loss of efﬁ ciency, equipment

damage, and possible ﬁ re risk.

This unit is not supplied with air ﬁ lter(s) and has no means

for accommodating internal air ﬁ lter(s). The installer is

responsible for installing a ﬁ ltration system into the return

air duct of this system. The ﬁ lter(s) of this system should

be checked at monthly.

It is very important to replace or clean the ﬁ lter(s) installed

in the return air duct of this system. A clogged ﬁ lter could

cause airﬂ ow related problems and reduce the overall

efﬁ ciency of your unit. Depending upon which type of ﬁ lter

was installed with your unit, clean (permanent) or replace

(disposable) ﬁ lter(s) of your system at the beginning of

every heating sea son, the beginning of every cooling

season, and when an accumulation of dust and dirt are

visible on the ﬁ lter. IMPORTANT: Replace disposable

ﬁ lter(s) installed in your system only with the same

size dimensional ﬁ lters that are being replaced. Clean

permanent ﬁ lter(s) as described by the manufacturer.

Motor Lubrication

The motors for the circulating air blower, outdoor fan, and

combustion blower are pre-lubricated and sealed by the

manufacturer. No further oiling is required for the life of

this product.

Burner Maintenance

CAUTION:

Some components in the burner vestibule are

at high temperatures while the burners are

operating. Use caution to avoid personal injury.

Check the burner ﬂ ames at the start of every heating

season. Set the thermostat above the room temperature.

Remove the control access panel to the unit and visually

inspect the burner assembly to make sure that the ﬂ ame

is drawn directly into the center of the heat exchanger tube

(See Figure 2). In a properly adjusted burner assembly,

the ﬂ ame bends up and to the left at the end of the heat

exchanger tube, and the end of the ﬂ ame will be out of

sight around the bend. The ﬂ ame color should be blue,

however some light yellow streaks may occur on the outer

portions of the ﬂ ame.

Figure 2. Burner Inspection

TROUBLESHOOTING

Before you call a Technician, check the following:

• Check the thermostat setting. Make sure the system

mode and temperature settings are correct.

• Check the electrical panel for tripped circuit breakers.

• Check the ﬁ lters for dust accumulation.

• Check the unit and make sure it is clean and not

covered with grass or leaves.

• If the items above don’t resolve your problems, then

call your nearest service technician.

A. This appliance does not have a pilot. It is equipped with

an ignition device which automatically lights the burner.

Do not try to light the burner by hand.

B. BEFORE OPERATING smell all around the appliance

area for gas. Be sure to smell next to the ﬂ oor because

some gas is heavier than air and will settle on the ﬂ oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone

in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or move

by hand, do not try to repair it, call a qualiﬁ ed service

technician. Force or attempted repair may result in a ﬁ re

or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

1. ATTENTION! Lire d’abord la liste des mesures de

sécurité ci-dessus.

2. Mettre le thermostat à la position minimale.

3. Couper le courant électrique qui mène à l’appareil.

4. Cet appareil ménager étant doté d’un système

d’allumage automatique, ne pas essayer d’allumer le

brûleur manuellement.

5. Retirer le panneau/volet d’accès de commande (panneau

supérieur s’il s’agit d’un modèle à deux panneaux).

6. Faire tourner le robinet à gaz dans le sens des aiguilles

d’une montre

pour l’amener sur la position OFF

(Arrêt) (Voir Figure 1).

7. Attendre cinq (5) minutes pour s’assurer de la

dissipation du gaz.

En cas d’odeur, ARRÊTER LE PROCÉDÉ. Suivre les

instructions ci-dessus (Section B). En l’absence de

toute odeur de gaz, avancer à l’étape suivante.

8. Faire tourner le robinet à gaz dans le sens inverse des

aiguilles d’une montre

pour l’amener sur la position

ON (Marche) (Voir Figure 1).

9. Remettre le panneau/volet d’accès de commande en

place (panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

10. Rebrancher l’appareil sur le réseau électrique.

11. Ajuster le thermostat à la position désirée.

12. Si l’appareil ne fonctionne pas, suivre les “Directives

d’arrêt” cidessous et appeler le technicien de service.

A. Cet appareil ménager n’a pas de veilleuse. II est doté

d’un système d’allumage automatique. Ne pas essayer

d’allumer le brûleur manuellement.

B. AVANT L’USAGE. Attention à une possible odeur de

gaz surtout au niveau du plancher où les gaz les plus

lourds ont la tendance de se concentrer.

EN CAS D’ODEUR DE GAZ.

• Ne mettre en marche aucun appareil électrique.

• Ne toucher à aucun commutateur électrique, ne pas

employer le téléphone.

• Quitter le bâtiment immédiatement et avertir la

compagnie du gaz en utili sant le téléphone d’un voisin.

• A défaut de la compagnie du gaz, avertir le service des

pompiers.

C. Enfoncer ou faire tourner le robinet à gaz à la main

seulement. Ne jamais utiliser d’outils. S’il n’est pas

possible de faire tourner ou d’enfoncer le robinet à la

main, ne pas essayer de le réparer. Faire appel à un

spécialiste. Forcer ou tenter de réparer le robinet pourrait

être à l’origine d’une explosion ou d’un incendie.

D. II est déconseillé d’utiliser cet appareil en contact

prolongé avec l’eau. Faire inspecter ou remplacer

toute commande par un technicien qualiﬁ é si un des

systèmes de contrôle du gaz s’est trouvé sous l’eau.

1. STOP! Read the safety information above on this

label.

2. Set the thermostat to the lowest setting.

3. Turn off all electrical power to the appliance.

4. The appliance’s ignition device automatically lights

the burner. Do not try to light burner by hand.

5. Remove the control access door/panel (upper door if

two-door model).

6. Move the gas control knob clockwise

to “OFF”.

(See Figure 1)

7. Wait ﬁ ve (5) minutes to clear out any gas. Then smell

for gas, including near the ﬂ oor. If you smell gas,

STOP! Follow “B” in above information. If you don’t

smell gas, go to the next

step.

8. Move the gas control knob

counterclockwise

“ON”. (See Figure 1)

9. Replace the control

access door/panel (upper

door if two-door model).

10. Turn on all electrical

power to the appliance.

11. Turn the thermostat to a desired setting.

12. If the appliance will not operate, follow the

instructions “To Turn Off Gas To Appliance” and call

your service technician or gas supplier.

7106750 (Replaces 710329A) (03/07)

1. Mettre le thermostat à la position minimale.

2. Débrancher l’appareil en prévision de la réparation.

3. Retirer le panneau/volet d’accès de commande (panneau

supérieur s’il s’agit d’un modèle à deux panneaux).

4. Faire tourner le robinet à gaz dans le sens des

aiguilles d’une montre

pour l’amener sur la

position OFF (Arrêt) Ne pas forcer (Voir Figure 1).

5. Remettre le panneau/volet d’accès de commande en

place (panneau supérieur s’il s’agit d’un modèle à deux

panneaux).

POUR VOTRE SÉCURITÉ.

À LIRE AVANT L’EMPLOI

FOR YOUR SAFETY READ

BEFORE OPERATING

1. Set the thermostat to the lowest setting.

2. Turn off all electrical power to the appliance if service is

to be performed.

3. Remove the control access door/panel (upper door if

two-door model).

4. Move the gas control knob clockwise

to “OFF”. Do

not use force. (See Figure 1)

5. Replace the control access door/panel (upper door if

two-door model).

ATTENTION! L’inobservation de ces instructions

peut entraîner un incendie ou une explosion pouvant

causer des dam mages à votre propriété à votre

personne, ou la mort.

WARNING: If you do not follow these instructions

exactly, a ﬁ re or explosion may result causing property

damage, personal injury, or loss of life.

TO TURN OFF

GAS TO APPLIANCE

DIRECTIVES D’ARRÊT

KNOB

(ROBINET)

Figure 1

MODE D’EMPLOI

OPERATING INSTRUCTIONS

¢7106757¤

Figure 3. Gas Valve Label

708258A (Replaces 7082580)

Speciﬁ cations & illustrations subject to change without notice or incurring obligations.

O’Fallon, MO | Printed in U.S.A. (09/10)

¢708258E¤

MAINTENANCE ITEM

FREQUENCY OF MAINTENANCE

BEGINNING OF EACH

HEATING SEASON

END OF EACH

HEATING SEASON

MONTHLY

Verify area around the unit is free of

combustible materials

Verify combustion and ventilation air is

not restricted

XXX

Verify no signs of physical deterioration

of the furnace

XXX

Verify burner ﬂ ame

Inspect unit support

Inspect return air connections

Clean or replace ﬁ lter(s)

Clean blower compartment

Clean burner vestibule

Table 1. Maintenance Schedule

Westinghouse R6GE Manuel utilisateur

Marque: Westinghouse

Modèle: R6GE

Taper: Manuel utilisateur

Ce manuel convient également à

DF6SF

Télécharger le PDF

rapport

dans d''autres langues

English: Westinghouse R6GE User manual

Documents connexes

Maytag PPG2GI Manuel utilisateur

Westinghouse R6GE Manuel utilisateur

Ce manuel convient également à

Westinghouse R6GE Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents