Maytag MDB8951AWB - Jetclean II Series Fully Integrated Dishwasher Mode d'emploi

Marque: Maytag

Modèle: MDB8951AWB - Jetclean II Series Fully Integrated Dishwasher

Catégorie: Lave-vaisselle

Taper: Mode d'emploi

Ce manuel convient également à

MDB-9

Table of Contents

Safety . . . . . . . . . . . . . . . . . . . . . 1

What Can &

Cannot be Washed . . . . . . . . . . .2

Operating Tips . . . . . . . . . . . . . . 3

Loading . . . . . . . . . . . . . . . . . 3-6

Dishwasher Use . . . . . . . . . . . . 7

MDB-9

Use & Care Guide

art No. 6 9201

6 A

www

.maytag.com

Cycles, Options

and Lights . . . . . . . . . . . . . . 8-11

Care & Cleaning . . . . . . . . . . . 12

Troubleshooting . . . . . . . . 13-14

Warranty & Service . . . . . . . . 15

Guide d’utilisation

et d’entretien . . . . . . . . . . . . . .16

Guiá de Uso y Cuidado . . . . . 32

WARNING – Hazards or unsafe practices which COULD

sult in severe personal injury or death.

WARNING

CAUTION – Hazards or unsafe practices which COULD

sult in minor personal injury or property damage.

CAUTION

nstaller:

lease leave this guide with this appliance.

Consumer: Please read and keep this manual for future

reference. Keep sales receipt and/or cancelled check as

proof of purchase.

Model Number ____________________________________

Serial Number_____________________________________

ate of Purchase __________________________________

If you have questions, call:

1-800-688-9900 USA

1-800-688-2002 CANADA

1-800-688-2080 (U.S. TTY for hearing or speech

impaired) (Mon.-Fri., 8 am-8 pm Eastern Time)

Internet: www.maytag.com

In our continuing effort to improve the quality and perfor-

mance of our appliances, it may be necessary to make

changes to the appliance without revising this guide.

For service information, see page 15.

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in this

manual are not meant to cover all possible conditions and

situations that may occur. Common sense, caution and care

must be exercised when installing, maintaining or operating

the dishwasher.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

Check with the installer to make sur

e the appliance

has been properly grounded to avoid possible

electrical shock. Be sure you read the important

personal safety instructions before you use this

dishw

asher

WARNING

Important Safety Instructions

Safety

1. Read all instructions before using the dishwasher.

2. Use the dishwasher only for its intended function.

3. Disconnect electrical power to dishwasher before

attempting to service.

4. To avoid electrical shock hazard, the sides and back

must be enclosed and the front panels must be

attached before electrical power is applied to the

dishwasher. Refer to the installation instructions for

proper grounding procedures.

5. Connect to a properly rated, protected and sized

power supply circuit to avoid electrical overload.

6. Children should never be permitted to operate, or play

in, with, or around this dishwasher.

7. To reduce the risk of injury when loading items to be

washed, sharp or pointed items should be located with

the handles up. Also, load sharp items so they are not

likely to damage the door seal.

8. Do not touch the heating element on the bottom of

the tub during or at the completion of a cycle. It will

be hot.

9. Use only detergents and rinse additives designed for a

residential automatic dishwasher. Never use soap,

laundry detergent, or hand washing detergent in your

dishwasher. Keep these products out of reach of

children.

10. Do not sit, stand on or abuse the door or dish racks of

the dishwasher.

11. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more.

Hydrogen gas is

explosive. If the hot water system has not been used

for such a period, turn on all hot water faucets and let

the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

this process.

12.

Do not wash plastic items unless marked “dishwasher

safe” or the equivalent. For plastic items not so

marked, check the manufacturer’s recommendations.

13. Do not tamper with controls.

14. To prevent accidental child entrapment and

suffoc

ation risks, always remove the door to the

washing compar

tment when removing an old

dishwasher from service or discarding it.

15.

Use caution when unloading the dishwasher. Dishes

will be hot if unloaded shor

tly after a c

ycle has

completed.

16. Certified residential dishwashers are not intended for

licensed food e

ablishments.

17. To avoid water, mold or mildew damage to your home,

inlet and drain hose connections should be checked

periodic

ally for leaks.

Save These Instructions

for Future Reference

When using your dishwasher, follow basic

precautions, including the following:

WARNING

roduct

s with a label have been listed with

Underwriter’s Laboratories, Inc. – those with a CSA tag have

been listed with Canadian Standards Association.

Never

thele

ss, as with any other equipment using electricity

and moving par

s, there is a potential hazard.

What Can and Cannot Be Washed

ooden Items

Most tableware, cookware and flatware can safely be washed in your dishwasher. Check with the manufacturer.

Yes, except anodized.

Yes, except antique or

hand-painted.

Yes, except antique or

delicate crystal.

Not recommended.

Yes

Yes, top rack, except

disposable plastic

items.

Yes

No, if has commercial

“

darkening”

High water temperature and detergents may affect finish.

Seasoning will be removed, and iron will rust.

Always check manufacturer’s recommendation before washing.

Antique, hand-painted or over-the-glaze patterns may fade. Gold

leaf may discolor.

Always check manufacturer’s recommendation before washing.

Some types of leaded crystal may etch with repeated washings.

May leave a dingy deposit or stain on dishwasher interior.

A specialty glass called milk glass can yellow with repeated

dishwasher washing.

Will discolor.

Always check manufacturer’s recommendation before washing.

Plastics vary in their c

apacity to withst

and high water

temperatures and detergents. Disposable plastic items are not

dishwasher safe for this reason.

Run a Rinse Only cycle (select models) if not washing

immediately

. Prolonged cont

act with foods containing s

alt,

vinegar

, milk product

s or juice could damage finish.

Always check manufacturer’s recommendation before washing.

Run a Rinse Only cycle (select models) if not washing

immediately

. Prolonged contact with food containing salt, acid or

sulfide (eggs, mayonnaise and seafood) could damage finish.

Commercial “darkening” may be removed by detergent.

Wood may warp, crack or discolor.

Gold-Plated

Flatware

Glass

Crystal

Cast Iron

Aluminum

China/Stoneware

Pewter, Tin

Stainless Steel

Plastics

Sterling Silv

er or

Silverplate

Filters

MATERIAL DISHWASHER SAFE? SPECIAL INFORMATION

Before You Start

• Don’t prerinse. Simply scrape off any bones or

large food particles.

• If connected to a food waste disposer, make certain

the disposer is empty before starting the

dishwasher.

• Scrape off tomato-based food soils (see page 12).

•

Remove certain foods such as mustard,

mayonnaise, lemon juice, vinegar, salt or dressings

from stainless steel flatware as soon as possible.

These foods may cause rusting and pitting if allowed

to remain in contact with the surface for an extended

period of time.

Operating the Dishwasher

1. After loading the dishwasher and adding detergent,

select the desired cycle and options by pressing

the pads. T

he indicator lights for the selected cycle

and options will illuminate. To cancel an option

press the pad again.

2. To start a cycle, close the door until it latches then

press the

START/Cancel pad once. After a pause,

the fill will begin. The display countdown (select

models) will flash until START/Cancel is pre

ssed.

Note

• If START/Cancel is not pressed within 30

seconds of choosing your cycle, the dishwasher

will turn off.

he dishwasher remembers your last cycle so you

do not have to reset the cycle each time. To start

the dishwasher using the same cycle and options

selected on the previous wash, just press the

START/Cancel pad.

3. To cancel a running cycle, press the

START/Cancel pad once. The dishwasher will

drain, then shut off. To turn the dishwasher off

without draining, pre

ss the

ART/Cancel

pad

twice. T

o prevent unplanned cycle or option

changes, these selections are “locked in” after 1

minute.

Note

• If a cycle pad is pressed after the controls have

been “locked in,” the light above the current c

ycle

will flash three times.

Adding a Forgotten Item

For best cleaning, the forgotten item should be added

early in the cycle.

1. Grasp door handle and unlatch door without

opening completely. All lights will flash to indicate

that the cycle is suspended.

2. Wait for the water circulation to stop.

3. Open the door and add the item.

4. Close and latch the door. Lights will stop flashing

when the door is properly shut. After a slight delay,

the c

ycle resumes automatically at the point of

interruption.

Notes

• If the door is opened during a running cycle,

there may be up to a 30 second delay before the

dishwasher restarts after closing the door.

• Extended interruption of the wash cycle is not

recommended.

General Recommendations

(Rack f

eatures vary by model)

•

Items c

an be centered behind a single tine or loaded

at an angle to maximize space.

• Avoid blocking or preventing the spray arms from

spinning freely. Do not allow items to extend beyond

the racks.

• Face soiled surfaces toward the center of the

dishwasher

or be

st dishwashing re

sult

s follow guideline

s on

following pages to determine the best arrangement for

your items.

Cont.

Operating Tips

10 Place Setting Load

Upper Rack

Glasses, cups, stemware, light-weight plastics, plates,

bowls, pans, long-handled utensils etc. c

an be loaded

in this rack.

Do not load glasses over the tines.

The Stack-Rack™ (select

models) on the right side

of the upper rack folds

up or down for loading

flexibility

. Fold it down to

hold long-handled

knive

s, spatulas and

spoons or short items like cups or juice glasses. Fold it

up for taller items like glasses, bowls, plates, etc.

The edge of the Stack-

Rack™ (select models) is

designed to hold

stemware in place. Taller

stemware will fit better on

the right side as the

upper rack is deeper on

this side.

The Folding Tines (select

models) located in the

front right corner provide

convenient loading space

for large, bulky items like

pots and pans or mixing

bowls.

To lower tines, carefully push the tines out of each

holder toward the center of the rack and lay the tines

down.

The Cup Clips (select

models) located in the

center of the upper rack

can be used to hold

light-weight plastic items,

cooking utensils, knives,

etc. in place. Clip the

item between the tine

and the clip.

The V

ari-Lock™ Snugger

(select models) on the

left secure

s lightweight

items in place. It c

an be

adjusted by grasping the

wavy wire and rot

ating it

left to snug items against

the outer rack or to the

right to rest on top of light items.

Do not load items

on top of the wire.

or be

st re

sults with tall

glasses, rest the bottom of

the glass against the wavy

wire of the Vari-Lock™

Snugger (select models).

Upper Rack

3 saucers are

loaded on the

rack under the

Stack-Rack™

Shelf

(select

models)

Lower Rack

A variety of items such as

dinner plates, mixing bowls,

pots and pans and baking

dishes can be loaded in this

rack.

Tall items such as bakeware

and large platters can be

placed on the left side.

With the Stack-

Rack™ (select

models) shelf

raised, thin items

like cookie sheets

or pizza pans

may be placed

along the left

side. With the shelf down, two levels of glasses and

cups can be loaded. St

ack-R

ack™ style varies by

model.

Positioning the Fold-

Away™ T

ines (select

models) flat in the back,

left corner provides

convenient loading space

for large, bulky items like

pots and pans or mixing

bowls.

Convertible Tines (select

models) in the back, right

corner can be adjusted to

provide narrow spacing for

loading plate

s or wide spacing

for loading deep bowls, pots or

pans. Flip tines up for narrow

spacing or down for wider

spacing.

Utensil Baskets

Removable Standard Utensil Basket (select

models)

For best cleaning results, prevent

items from nesting together by

placing some items in the basket

with handles up and some with

handles down. Load knives

handles up and spoons and forks

handles down, through the slots

in the hinged covered section(s)

(when closed).

Be sure that thin, finely pointed items do not extend

through the basket. This could block the lower wash

arm.

Small, lightweight items like baby spoons and plastic

measuring spoons should be placed in the section(s)

with the hinged cover(s).

Split & Fit™ Utensil Basket

(select models)

The split silverware basket can

be separated and placed in

several locations in the lower

rack. Load flatware and utensils

into both sections or just one,

depending on your load.

To split the basket, hold the

basket

firmly along

the side

Unlock

baskets as

shown here.

Odds & Ends Basket (select models)

Use this supplement

basket in the upper rack

for loading miscellaneous

items and utensils. This is

also a safe place to load

sharp knive

s and pointed

items.

Cont.

Back

Adjustable Rack (select models)

The Adjustable Upper Rack (select models) can be

raised or lowered to accommodate taller plates,

platters, pans, etc. optimizing useable space in both

upper and lower racks. Full size dinner plates can be

loaded in the upper rack if it is in the lower position.

Always adjust the upper rack before loading.

To lower the rack:

1. Pull the rack fully out.

2. Place thumbs on

each lever on

the adjuster

while holding

rack with hands.

3. Press down on

the levers with

thumbs and

push rack down. The rack will come to a stop when

it is in position.

To raise the rack:

1. Pull the rack fully out.

2. Place hands on both sides and lift up until rack

comes to a stop and latches in place.

Notes

• The dishwasher will not

operate correctly if the

wash arm is not aligned

with one of the water

inlet holes on back w

all

of the dishw

asher.

•

he left and right side adjusters on the racks

must both be fully in the upward or downward

position for proper connection.

Removing the Upper Rack

The rack can be removed when tall or oversized items

need to be loaded into the lower rack. Unload the

rack before removing it from the dishwasher.

To remove rack with tab-lock rack stops:

1. Roll the rack

⁄3 to

⁄2 of the way out.

2. Locate the rack stops at the end of each track.

Squeeze the tab in the middle of the rack stop and

pull the rack stop straight out. Take care to support

the rack while removing the rack stops.

3. Roll the rack all

the way out of the

track and remove

from the

dishwasher.

To replace:

Replace the

dishwasher rack by guiding the

wheels into the tracks.

2. Push each rack stop squarely into the end of the

track until the catch pops into the small hole on the

side of the track.

Adjusters

Tab Lock

Rack Stop

Tab Lock

Style may vary by model

Hot Water

For optimal cleaning and drying results, hot water

is necessary. The incoming water temperature

should be 120° F (49° C) to properly activate the

detergent and melt greasy food soils.

To check the incoming water temperature, turn on the

hot water faucet nearest the dishwasher and let it run

into a glass in the sink. Place a candy thermometer in

the glass and check the temperature once it has

stopped rising.

Detergent

Use a detergent designed specifically for use in an

automatic dishwasher. Be sure it is fresh. Store

granular detergent in a cool, dry place (not under the

sink).

Recommended Amount

Too little detergent results in poor cleaning, hard water

filming/spotting and poor drying. Too much detergent

can cause permanent etching/cloudiness.

Suds can cause the dishwasher to overflow. Measure

the detergent c

arefully and use only detergents

designed for use in a dishwasher. Less detergent is

needed in soft water. Try another brand of detergent if

sudsing continues.

The amount of detergent to use is determined by the

hardne

ss of the water and soil level of the load. Refer

to the following char

t for detergent usage

recommendations.

In extr

emely har

d w

ater conditions (13 grains per

gallon or mor

e*), it is difficult to achiev

e good

results with any dishwasher. A mechanical water

softener may be necessary to improve water

quality, detergent effectiveness, and protect the

dishwasher parts from the damage that hard

water can cause.

Add recommended amount of detergent to each cup

as shown and close the detergent lid.

Do not use detergent with the Rinse Only (select

models) cycle. Leave the detergent lid open when

running R

inse Only (select models).

Rinse Aid

Regular use of a rinse aid improves drying,

reduces spotting and filming, and reduces

moisture left on the dishw

asher interior

An automatic rinse aid dispenser is loc

ated next to the

detergent cup.

The window next to the dispenser cap indicates when

the rinse aid reservoir needs to be refilled. When the

level of rinse aid is below the indicator marks and the

window is nearly clear, it is time to refill the dispenser.

Check the dispenser monthly

To add rinse aid to the

dispenser, turn the cap

counterclockwise to open.

Remove the cap and pour

liquid rinse aid into the

opening. The amount of

rinse aid dispensed during

the c

ycle is adjust

able by moving the lever inside the

reservoir area. For most water conditions use the

manufacturer recommended setting of “2”

. Adjust it up to

the “MAX” setting for hard water. Set the lever anywhere

between these amounts as needed to get the best results.

Replace the c

ap and turn it clockwise to close.

*Your local water utility or state university extension service can tell

you the degree of water hardne

ss in your area.

Dishwasher Use

6 tsp

7 tsp

6 tsp

7 tsp

8 tsp

Light Soil

Normal Soil

Heavy Soil

Light Soil

Normal Soil

Heavy Soil

All Levels

2 tsp

4 tsp

5 tsp

TER

HARDNESS*

LEV

PRE-WASH

DETERGENT

MAI

N W

ETERGENT

Soft (0-4 gpg)

Medium (5-9 gpg)

Hard (10-12 gpg)

Cycles

TIME NUMBER OF

CYCLE DESCRIPTION (APPROX. WASHES/RINSES

MINUTES)

Heavy Wash

Normal Wash

Light W

ash

Auto Clean

(select models)

Rinse Only

Insta-W

ash

(select models)

Long cycle for heavy food soils. 132 2 washes/3 rinses

Medium cycle for average food

soils. Precision Clean™ Turbidity 97-117 1-2 washes*/1-2 rinses*

sensor is active with this cycle.

Short cycle for light food soils. 82 1 wash/2 rinses

Designed to select the number

of water fills best suited for the

soil level of each load. Precision 94-128 1-2 washes*/2-3 rinses*

Clean™ Turbidity sensor is active

with this cycle.

Rinses dishes being held until 9 1 rinse

there is a full load.

Quick cycle for light food soils.

38 1 wash/2 rinses

Does not include drying time.

Notes

• Depending on water temperature, there may be time added to the cycle to bring water up to temperature.

• Cycle times shown in the numerical display (select models) will increase or decrease, based on each load’s soil

level, water temperature and selected options.

• Only the following certified cycles have been designed to meet NSF requirements (NSF/ANSI 184 Residential

Dishwasher) for sanitization: Auto Clean (select models), Heavy Wash, Normal Wash and Light Wash.

* Number of fills will vary depending on the soil level of each load.

Choose the cycle that best describes your dishload by pressing the corresponding touchpad. (See page 3,

Operating Tips, for how to begin the cycle).

Cycles, Options and Lights

Heated Dry

* Only the

se cycle

s have been designated to meet N

SF requirements (NSF/ANSI 184 Residential Dishwasher) for sanitization.

Start/Cancel

Delay

Control Lock Option

(select models)

Starts and stops dishwasher. See page 3 under Operating Tips: All Cycles

Operating the Dishwasher, for explanation.

Used to automatically start the cycle at a later time. See page 10 All Cycles

for instructions.

ocks control touchpad to prevent unwanted use. See page 10

All Cycle

for instructions.

Options

OPTION DESCRIPTION USE WITH CYCLES

ToughScrub™/

ToughScrub™ Plus

(select models)

Sanitize

(select models)

Hi Temp Wash

(select models)

160° Wash

(select models)

Hi Temp Wash provides additional heat during the wash portion All cycles

of the cycle, which ensures proper water temperature for better (except Rinse Only

cleaning and drying results. It also adds an additional rinse to [select models])

the cycle which improves results in hard water situations.

Selected when washing loads with hard-to-remove food soils. Heavy Wash

Depending on which cycle is being used, this option adds Normal Wash

heat and/or wash time to the wash cycle. Light Wash

Auto Clean

(select models)

Sanitizes dishware. When cycle monitor recognizes that the Heavy Wash*

proper conditions have been met, Sanitized light will activate Normal Wash*

at the end of the cycle. Sanitization may not be achieved if Light Wash*

there is an interruption of the cycle, power failure or if the Auto Clean*

(

select models)

incoming water temperature is below 120° F (49° C).

Raises temperature in the final rinse to 160° F. This option can

be used with any cycle except Insta-Wash (select models)

and Rinse Only.

For enhanced drying results select this option. When

Heated

Dry is not selected, towel drying of some items such as plastic

and items with non-stick surfaces may be necessary and more All cycles

moisture may be noticed adhering to the dishwasher interior. (except Rinse Only)

In models with plastic interiors, it is normal to notice vapor

escaping from the door vent as the heat dries your dishes.

Vapor will escape even if

Heated Dry is not selected.

In addition to choosing a cycle from page 7, choose as many available options as are needed for your dishload.

Heavy Wash

Normal Wash

Auto Clean*

(select models)

CAUTION – In models with plastic interiors, it is normal to notice vapor escaping from the door vent in the upper left corner

of the door as the heat dries your dishes. The vapor is hot and may cause minor burns.

CAUTION

Cycles, Options and Lights

Lights/Display

Delay

The Delay option can be used to automatically start

the cycle at a later time to reduce daytime heat

buildup in the home or to take advantage of reduced

energy costs if available in your area. This option is

also useful for conserving hot water at times of high

household usage (showers, laundry).

To set up a Delay:

1. Select the appropriate cycle and options for the

load. Close the door.

2. Press the

Delay pad until the desired amount of

delay time is selected.

3. The Delay indicator and the count down display

(select models) will flash until the

START/Cancel

pad is pressed.

4. As soon as the

START/Cancel pad is pressed, the

flashing will stop and the delay time will begin

counting down. The Delay indicator will remain lit

until the delay time has counted down.

5. The cycle will automatically start as soon as the

delay time expires.

Note

• If

30 seconds elapse between setting the cycle

and options and pressing the

START/Cancel

pad, the dishwasher will turn off.

To cancel a Delay:

When the delay is counting down, press the Delay pad

again. The indicator light will go out and the cycle will

start or resume immediately.

To cancel a Delay and the cycle:

•

ART/Cancel

once to drain and turn off the

dishwasher.

• Press START/Cancel twice to turn dishwasher off

without draining.

Control Lock Option (select models)

The control touchpads can be locked to prevent

unwanted use. If this feature is activated between

cycles, the dishwasher cannot be operated until the

controls are unlocked. If desired, the controls can be

locked after a cycle or delay has started.

Setting the Control Lock:

1. Press the Heated Dry pad for three seconds.

2. An indicator light next to the lock graphic will

illuminate when the controls are locked.

To Cancel:

1. Press the Heated Dry pad for three seconds.

2. The indicator light will go off.

Notes

• If a cycle or option pad is pressed after the

controls have been locked, the indicator light next

to the lock graphic will flash five times. On

selected models with a countdown display, the

display will flash an “L” simultaneously with the

lock indicator.

• This option does not lock the door, only the

dishwasher controls.

Cycles, Options and Lights

Lights/Display (select models)

INDICATOR DESCRIPTION

Time Remaining Display

(select models)

Clean Light

Drying Light

(select models)

Washing Light

(select models)

Heating Delay Light

(select models)

Sanitized Light

(select models)

Shows approximate minutes remaining in a cycle. The symbol “2H” will appear when

cycle time is greater than 99 minutes. Cycle times shown in the numerical display

(select models) will increase or decrease, based on each load’s soil level, water

temperature and selected options.

Illuminates at the end of the cycle and remains lit until the door has been open for 30

seconds continuously.

Illuminates during the entire dry period and goes out when the cycle is completed.

Illuminates during all rinse and wash portions of the cycle.

Illuminate

s when cycle is being extended to heat the water.

Illuminates at the end of the cycle when conditions have been met to achieve

sanitization. The light will remain lit until the door has been open for 30 seconds

continuously.

Notes

• When Sanitize is selected, cycles are monitored to assure sanitization. The Sanitized light will not activate if

sanitization requirements are not met. This could happen if the cycle is interrupted, power failure occurs or

incoming water temperature is below 120° F (49° F).

• The Clean and Sanitized indicator lights (select models) will not relight after a power failure until after the next cycle

is run.

Cycles, Options and Lights

General Recommendations

• The dishwasher interior is normally self-cleaning.

Periodically check the bottom of the dishwasher tub

to see if any large particles remain.

• Wipe the edge of the inner door liner to remove any

food soil splashes which occurred during loading.

• When cleaning stainless steel, always wipe with the

grain.

Never use products containing chlorine bleach

or citric acid.

•

The color from some tomato-based food soils may

occasionally adhere to various components of the

dishwasher interior, causing temporary discoloration.

To minimize this:

• Remove excess tomato-based food soils from dishes,

before loading.

• Run the Heavy Wash cycle when washing loads

containing tomato-based food soils.

• Use a dishwasher detergent that contains chlorine to

better fight staining.

Care and Cleaning

Storage/Moving

Fill detergent cup with a fresh-scented dishwasher

detergent or baking soda and select the

Normal Wash

cycle. Allow the dishwasher to complete the cycle. Then

turn the water supply off and drain the dishwasher. To

drain, press the

START/Cancel pad once to activate

the dishwasher

. P

ress

ART/Cancel

again to activate

the drain. Operate the drain twice to ensure most of the

water is removed. Last, disconnect the electrical supply

and prop open the door.

hen turning the water supply to the home off, the

water shut off at the dishwasher must be turned off also.

LOCATION SOIL LEVEL TREATMENT

Standard Exterior

Stainless Steel

Exterior

(select models)

Interior

Light to moderate Soft damp cloth and liquid spray cleaner.

Do Not use abrasive powders or cleaning pads.

Daily cleaning and light soil

Soft cloth or sponge and one of the following:

• Mild detergent and water

• A solution of white vinegar and water

• Formula 409 Glass and Surface Cleaner*, or

similar

multi-surface cleaner

•

Do Not use products containing chlorine

bleach or citric acid.

Follow with rinse and dry

Moderate to heavy soil Soft cloth or damp sponge and Bon Ami*.

Follow with rinse and dry

Streaks or fingerprints/restore shine Soft cloth and Stainless Steel Magic Spray**.

Discoloration Soft cloth or damp sponge and Cameo Stainless

Steel Cleaner*. Rinse immediately and dry

Light to moderate Soft cloth or damp sponge.

Discoloration, or tomato-based st

ain

witch dishwasher detergent to chlorine-based

product.

*Brand names are trademarks of the respective manufacturer.

**Call 1-877-232-6771 to order.

Troubleshooting

CHECK THESE POINTS TO HELP SAVE YOU TIME AND MONEY.

PROBLEM

Dishwasher will not fill

Dishwasher will not drain/

water in tub bottom

Dishwasher adds water at

end of cycle

Detergent cup is not empty

Dishwasher seems noisy

Cycle takes too long

Dishwasher has an odor

Dishw

asher leaks

Indicator lights flashing

SOLUTION

• Press the START/Cancel pad to start the dishwasher.

• Be sure door is latched securely.

• Be sure the water is turned on.

• Check that the pad is properly selected for a cycle.

• Check your home’s circuit breaker or fuse box.

• Check inlet hose for a kink.

• Check water valve inlet for sediment and clean if necessary.

• If hooked up to a food waste disposer, be sure the knock-out is removed from the

disposer inlet.

• Check for food obstruction in the drain or disposer.

• Check drain hose for a kink.

• Check your home’s circuit breaker or fuse box.

• Check that the cycle is completed.

• This is normal. The sensor (select models) in the pump must stay submerged so a

short fill of water is added after the cycle’s last drain.

• Check that the cycle is completed.

• Be sure dispenser is not blocked.

• Use fresh detergent stored in a cool, dry place.

• A water valve hiss during fill is normal.

• Water circulation sounds are normal.

• A thumping sound may be a wash arm bumping an item that is extending beyond the

racks. Readjust load to avoid obstructing wash arm.

• Chopping or grinding sounds may be heard as the internal chopper blade chops hard

items like fruit seeds, nuts, etc.

• Humming during the drain is normal.

• A snap noise is the detergent cup lid hitting the door liner when the dishwasher door

is opened at the end of the cycle. This is normal.

• Proper installation affects the noise level.

•

ToughScrub

, ToughScrub

Plus or Sanitized (select models) has been selected

and the cycle is extended to heat water.

• Check to see that the incoming water temperature is 120° F (49° C).

• Run dishes being held in the dishwasher through a Rinse Only cycle (select models).

• Many dishwashers have a “new” smell when first installed. This will dissipate with use.

• Dishwasher may not be draining properly. (See “Dishwasher Will Not Drain” section.)

• For a strong odor, place baking soda in both sides of the detergent cup. Select Light

Wash cycle and allow the water to circulate for about 10 minutes. Interrupt the cycle

by unlatching the door and let it st

and overnight. Re

art the dishwasher by latching

the door and allow it to complete the cycle. Another alternative is to use a dishwasher

cleaning product such as Jet-Dry Dishwasher Cleaner*.

•

Check that the dishwasher is level. (Refer to the Inst

allation Instructions.)

• Suds can cause the dishwasher to overflow. Measure the detergent carefully and use

only detergents designed for use in a dishwasher. Less detergent is needed in soft

water. Try another brand of detergent if sudsing continues.

• Follow directions closely on how to add a forgotten item (pg. 3).

• To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached.

• The countdown display (select models) flashes after a cycle is selected until the

START/Cancel pad is pressed.

• The countdown display (select models) and the delay indicator flash after a delay is

selected until the S

ART/

Cancel pad is pre

ssed.

• All active display indicators flash if the door is opened during a running cycle or delay.

• The currently selected cycle flashes if an attempt is made to change the cycle after

cycle “lock-in”.

• The lock indicator flashes and the countdown display (selected models) flashes an “L”

if a pad is pressed while the control lock is enabled.

*Brand name

s are trademarks of the re

spective manufacturer

Cont.

Display time drops

or increases

(select models)

Glasses are cloudy/

spotted

Food soil remains

on dishes

Items washed in the

dishw

asher or the

dishwasher tub itself

are stained/discolored

*Brand name

s are trademarks of the re

spective manufacturer

SOLUTION

• This is normal when the Auto Clean (select models) or Normal Wash cycle is selected and

he dishwasher decides to skip or add a drain and refill.

• Select Hi Temp Wash option.

•

Check water temperature. Incoming water should be 120° F (49° C).

•

Always use a rinse aid.

• Confirm that the cloudiness is removable by soaking the item in white vinegar for

approximately 5 minutes. If removed, the problem is due to hard water. Adjust detergent

amount being used to match water hardness (pg. 7). Be sure detergent is fresh, stored

properly and is a high quality brand.

• If cloudiness is not removable, it is etching. This is an erosion of the surface of the glassware

and can be caused by water that is too hot, from using too much detergent or by

prewashing. Detergent needs food soil to act upon. If etching has occurred, the glassware is

permanently damaged. To prevent further etching, adjust the detergent amount to match

the water hardness, stop prewashing, and use water heating options only when incoming

water temperature is below 120° F (49° C).

• Check water temperature. Incoming water should be 120° F (49° C).

• Run hot water at the sink before starting the dishwasher.

• Check water hardness and adjust detergent amount accordingly (pg. 7).

• Use fresh detergent stored in a cool dry place.

• Select proper cycle for the soil level (pg. 8).

• Select proper option,

ToughScrub

, ToughScrub

Plus or Hi Temp Wash (select models).

• Make sure the upper rack wash arm connector is correctly aligned in one of the water inlet

holes (pg. 6).

• Load items so they do not block the wash arms (pgs. 3-6).

• Load the utensil basket with knife handles up and spoon and fork handles down.

•

Do not place glasses over tines.

• Before loading, scrape off burnt on foods and wipe the starchy film from utensils used with

pasta, rice and oatmeal. These soils require more energy than the rest of the load to clean.

• Aluminum utensils or pans can leave marks when they rub against other items. Leave a

slight space between items.

• Iron deposits in the water can leave a yellow, brown or orange film on dishes or the

dishwasher tub. A rust filter may be needed. Check with a water treatment company.

• Separate silver or silver-plated silverware from stainless steel. These metals can be damaged

by contact with each other during washing.

• Color from tomato sauces may adhere to the interior parts of the dishwasher (pg. 12). If light

staining has occurred, leave the door open to oxidize the stain away. Use a dishwasher

detergent that contains chlorine to better fight staining.

• Certain dishwasher detergents may stain silver. Try another brand of detergent.

• Be sure

Heated Dry is selected.

• Water droplets may form on the inner door as part of the drying process.

•

Use a rinse aid separate from the detergent like Jet Dry* or Casc

ade R

inse Aid* regularly, to

improve drying. Turn the rinse aid selector toward the

MAX setting.

• Check water temperature. Incoming water should be 120° F (49° C).

• Select

Sanitize option.

• Increase detergent amount to match water hardness (pg. 7).

• Load properly. (pgs. 3-6)

• Plastic and items with non-stick surfaces are difficult to dry because they have a porous

surface which tends to collect water droplets. Towel drying may be necessary.

•

Glasse

s and cups with conc

ave bottoms hold water and require towel drying. L

ate these

items on the more slanted side of the rack for improved results.

• Load dishes according to instructions so they do not strike each other (pgs. 3-6).

•

ashing fine antique china/cryst

al in the dishwasher is not recommended.

• Do not load glasses over the tines.

• Do not overload.

•

Sanitize was not selected.

• Sanitization can only be achieved with the Auto Clean (select models), Heavy Wash, Normal

Wash or Light Wash cycles.

•

Sanitization may not be achieved if there is an interruption of the c

ycle, power failure or if

incoming water temperature is below 120

° F (49° C).

•

Be sure adjust

able racks (select models) are properly adjusted to upper or lower position

(pg. 6).

Dishware is chipped

PROBLEM

Items not properly

dried/moisture is

present on the

dishw

asher interior

after the dry cycle

Sanitized light does not

illuminate at the end of

the cycle (select

models)

Dishw

asher door will

not close

Warranty and Service

Warranty

Limited One Year Warranty -

Parts and Labor

For one (1) year from the original retail

purchase date, any part which fails in

normal home use will be repaired or

replaced free of charge.

Canadian Residents

The above warranties only cover an

appliance installed in Canada that has

been certified or listed by appropriate test

agencies for a compliance to a National

Standard of Canada unless the appliance

was brought into Canada due to transfer

of residence from the United States to

Canada.

The specific warranties expressed above are

the ONLY warranties provided by the

manufacturer. These warranties give you

specific legal rights, and you may also have

other rights which vary from state to state.

What is Not Covered By These Warranties

1. Conditions and damages resulting from any of the following:

a. Improper installation, delivery, or maintenance.

b. Any repair, modification, alteration, or adjustment not authorized by the

manufacturer or an authorized servicer.

c. Misuse, abuse, accidents, unreasonable use, or acts of God.

d. Incorrect electric current, voltage, electrical and/or gas supply.

e. Improper setting of any control.

2. Warranties are void if the original serial numbers have been removed, altered,

or cannot be readily determined.

3. Light bulbs, water filters and air filters.

4. Products purchased for commercial or industrial use.

5. The cost of service or service call to:

a. Correct installation errors. For products requiring ventilation, rigid metal

ducting must be used.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to and from the servicer.

6. Any food loss due to refrigerator or freezer product failures.

7. Expenses for travel and transportation for product service in remote locations.

8. Outside of the United States and Canada this warranty does not apply.

Contact your dealer to determine if another warranty applies.

9. Consequential or incidental damages sustained by any person as a result of

any breach of these warranties. Some states do not allow the exclusion or

limitation of consequential or incidental damages, so the above exclusion may

not apply.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call the

dealer from whom your appliance was purchased or call Maytag Services, LLC,

Customer Assistance at 1-800-688-9900 USA and 1-800-688-2002 Canada to

locate an authorized servicer.

• Be sure to retain proof of purchase to verify warranty status. Refer to WARRANTY

for further information on owner’s responsibilities for warranty service.

• If the dealer or service company cannot resolve the problem, write to Maytag

Services, LLC, Attn: CAIR

Center, P.O. Box 2370, Cleveland, TN 37320-2370, or call

1-800-688-9900 USA and 1-800-688-2002 Canada. U.S. customers using

TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

•

User’s guides, service manuals and par

s information are available from Maytag

Services, LLC, Customer Assistance.

Notes: When writing or calling about a service problem, please include:

a. Your name, address and telephone number;

Model number and serial number;

Name and addre

ss of your dealer or servicer;

d. A clear description of the problem you are having;

e. Proof of purchase (sales receipt).

CUSTOMER’S SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR

AS PROVIDED HEREIN. IMPLIED

WARRANTIES, INCLUDING WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED

TO ONE YEAR OR THE SHORTEST

PERIOD ALLOWED BY LAW. MAYTAG

CORPORATION SHALL NOT BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. SOME STATES AND

PROVINCES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF

CIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE

DURATION OF IMPLIED WARRANTIES OF

ERCHANTABILITY OR FITNESS, SO

THESE EXCLUSIONS OR LIMITATIONS

MAY NOT APPLY TO YOU. THIS

WARRANTY GIVES YOU SPECIFIC LEGAL

RIGHTS AND YOU MAY ALSO HAVE

OTHER RIGHTS, WHICH VARY STATE TO

STATE OR PROVINCE TO PROVINCE.

Table des matières

Sécurité

. . . . . . . . . . . . . . . . . . 14

Articles lavables ou non

en lave-vaisselle . . . . . . . . . . . 18

Conseils d’utilisation . . . . . . . 19

Chargement . . . . . . . . . . . 19-22

Utilisation du

lave-vaisselle . . . . . . . . . . . . . 23

MDB-9

Guide d’utilisation et d’entretien

Cycles, options et

témoins lumineux . . . . . . . 24-27

Entretien et nettoyage . . . . . . 28

Dépannage . . . . . . . . . . . . 29-30

Garantie et service . . . . . . . . . 31

Guiá de Uso y Cuidado . . . . . 32

Sécurité

Installateur : Veuillez laisser ce guide avec cet appareil.

onsommateur :

euillez lire et garder ce guide pour

consultation ultérieure. Conservez le reçu ou le chèque

encaissé comme preuve de l’achat.

Numéro de modèle ______________________________

Numéro de série ________________________________

Date d’achat ____________________________________

Pour des questions, appelez :

1-800-688-9900 aux É.-U. et 1-800-688-2002 CANADA

(Lundi au vendredi, 8 h à 20 h, heure de l’Est)

Internet: http://www.maytag.com

Dans le cadre de nos pratiques d’amélioration constante

de la qualité et de la performance de nos appareils, des

modifications peuvent être introduites sur les appareils

sans que cela donne lieu à une révision de ce guide.

Pour l’information sur le service, voir page 31.

Ce que vous devez savoir sur

les instructions de sécurtié

Les instructions de sécurité importantes et les avertissements

paraissant dans ce guide ne sont pas destinés à couvrir toutes

les situations et conditions éventuelles qui peuvent se

présenter. Il faut faire preuve de bon sens et de prudence lors

de l’installation, de l’entretien ou de l’utilisation de l’appareil.

Prenez toujours contact le fabricant, au sujet de problèmes

ou conditions que vous ne comprenez pas.

Reconnaissez les étiquettes, phrases

ou symboles sur la sécurité

1. Lire la totalité des instructions avant d’utiliser le lave-

vaisselle.

2. Utiliser le lave-vaisselle uniquement pour les

pplications.

. Débrancher le lave-vaisselle avant tout entretien.

. Pour éviter tout risque de choc électrique, les côtés et

l’arrière doivent être fermés et le panneau avant doit

être fixé avant de brancher le lave-vaisselle. Se

reporter aux instructions d’installation pour les

méthodes correctes de mise à la terre.

5. Brancher le lave-vaisselle à un circuit électrique

correctement protégé, d’une puissance nominale

appropriée et avec fils de calibre adéquat.

6. Il ne faut jamais laisser les enfants utiliser ou jouer

dans, avec ou autour du lave-vaisselle.

7. Pour réduire le risque de blessure lors du chargement

du lave-vaisselle, il faut placer les articles pointus ou

aiguisés avec le manche vers le dessus. De même,

loger les articles pointus pour qu’ils n’endommagent

pas le joint de la porte.

8. Ne pas toucher à l’élément chauffant au bas de la

cuve durant ou à la fin d’un cycle car il est chaud.

9. N’utiliser que des détergents et des agents de rinçage

conçus pour un lave-vaisselle résidentiel automatique.

Ne jamais utiliser de savon, de détergent lessiviel ou de

détergent de lavage à la main dans votre lave-vaisselle.

Garder ces produits hors de portée des enfants.

10. Ne pas s’asseoir, se mettre debout ou maltraiter la

porte ou les paniers du lave-vaisselle.

11. Sous certaines conditions, de l’hydrogène peut se former

dans un système d’eau chaude qui n’a pas été utilisé

pendant deux semaines ou plus.

L’hydrogène est un

gaz explosif

. Si le système d’eau chaude n’a pas été

utilisé pendant une telle période, ouvrir tous les robinets

d’eau chaude et laisser couler l’eau pendant plusieurs

minutes. Ceci diminuera l’accumulation d’hydrogène.

Comme il s’agit d’un gaz inflammable, ne pas fumer ou

utiliser de flamme vive durant cette opération.

12. Ne pas laver d’articles en plastique ne portant pas

l’indication « lavable en lave-vaisselle ». Pour des

articles en plastique sans indication, vérifier les

recommandations du fabricant.

13. Ne pas circonvenir les commandes.

14. Pour éviter tout risque d’enfermement et/ou de

suffocation accidentelle d’un enfant, toujours enlever

la porte du compartiment de lavage lorsque l’on

enlève un ancien lave-vaisselle ou qu’on le jette.

15. Faire preuve de prudence en déchargeant le lave-

vaisselle. La vaisselle peut être chaude si elle est

déchargée peu de temps après la fin d’un cycle.

16. Les lave-vaisselle à usage résidentiel certifié ne sont pas

conçus pour les établissements alimentaires

homologués.

17. Pour éviter que l’eau ou la moisissure ne détériore votre

habit

ation, vérifiez régulièrement le

s raccordement

d’arrivée d’eau et les tuyaux d’évacuation pour

d’éventuelles fuites.

Conserver ces instructions

ors de l’utilisation du lave-vaisselle, suivre ces

précautions de base :

AVERTISSEMENT

AVERTISSEMENT – risques ou pratiques non sûres, qui

OURRAIENT

résulter en de grave

s blessures ou même

la mort.

AVERTISSEMENT

NTI

N –

risque

s ou pratique

s non sûre

s, qui

POURRAIENT résulter en blessure mineure ou

d’endommager le produit.

ATTENTION

Vérifier avec l’installateur pour s’assurer que

l’appar

eil a été corr

ectement mis à la terre pour

éviter tout choc électrique. S’assurer de lire les

instructions de sécurité personnelles importantes

ant d’utiliser ce lav

e-vaisselle.

AVERTISSEMENT

Instructions de sécurité importantes

s produit

s por

tant une étiquette ont été homologués par

Underwriter’s Laboratories, Inc. – ceux portant une étiquette

CSA ont été homologués par la Canadian Standards Association

(CSA). Néanmoins, comme pour tout autre équipement utilisant

l’électricité et des pièces mobiles, il y a un danger potentiel.

Articles en bois

La plupart des articles de table et de cuisson ainsi que les couverts peuvent être lavés en sécurité dans le lave-vaisselle. Vérifier avec le fabricant.

Oui, sauf l’aluminium anodisé.

Non

Oui, sauf les pièces

d’antiquité ou peintes à la

main.

Oui, sauf les pièces

d’antiquité et le cristal

délicat.

Non recommandés.

Oui

Non

Oui, sur panier supérieur

sauf les articles en plastique

à jeter.

Oui

Non, s’il a subi un traitement

de « noircissement ».

Non

Couverts plaqués or

Verre

Cristal

Fonte

Aluminium

Porcelaine/Grès

Étain, fer blanc

Acier inoxydable

Plastiques

Argenterie ou

argent sterling

Filtres

MATÉRIAU SONT-ILS LAVABLES RENSEIGNEMENTS UTILES

EN LAVE-VAISSELLE?

De hautes températures et les détergents peuvent attaquer la finition.

L’apprêt serait enlevé et le fer rouillerait.

Toujours vérifier les recommandations du fabricant avant le lavage. Les

porcelaines fines, les motifs peints à la main ou sur le vernis peuvent s’estomper.

Les feuilles d’or peuvent se décolorer.

oujours vérifier les recommandations du fabricant avant le lavage. Certains

types de cristal au plomb peuvent se corroder après des lavages répétés.

Peuvent laisser un dépôt crasseux ou des taches à l’intérieur du lave-vaisselle.

Un verre spécial appelé « verre laiteux » peut jaunir par suite de lavages répétés

au lave-vaisselle.

Se décolorent.

Toujours vérifier les recommandations du fabricant avant le lavage. La capacité

des plastiques à résister aux hautes températures et aux détergents peut varier.

Les articles en plastique jetable ne sont pas lavables en lave-vaisselle.

Si ces articles ne sont pas lavés immédiatement, lancer un cycle Rinse Only

(Rinçage seulement) (certains modèles). Le contact prolongé avec la nourriture

contenant du sel, du vinaigre, des produits laitiers ou du jus peut endommager la

finition.

Toujours vérifier les recommandations du fabricant avant le lavage. Si ces articles

ne sont pas lavés immédiatement, lancer un cycle Rinse Only (certains modèles).

Le contact prolongé avec la nourriture contenant du sel, de l’acide ou des

sulfures (oeufs, mayonnaise ou fruits de mer) peut endommager la finition. Le

« noircissement » commercial peut être enlevé par le détergent.

Le bois peut se déformer, se fissurer ou se décolorer.

Articles lavables ou non en lave-vaisselle

Conseils d’utilisation

Avant de commencer

• Ne pas prérincer. Il suffit de jeter os et gros

morceaux de nourriture.

• Si le lave-vaisselle est raccordé à un broyeur à

déchets,

veiller à ce que celui-ci soit vide avant

de mettre le lave-vaisselle en marche.

• Gratter les taches tenaces laissées par les

aliments à base de tomate

(voir page 28).

•

Éliminer certains aliments (tels que moutarde,

mayonnaise, jus de citron, vinaigre, sel et

vinaigrettes)

des articles en acier inoxydable

aussi rapidement que possible.

Ces aliments

peuvent provoquer de la rouille et du piquage s’ils

restent en contact prolongé avec la surface.

Utilisation du lave-vaisselle

1. Après avoir chargé le lave-vaisselle et ajouté du

détergent, choisir le cycle désiré en appuyant sur la

touche correspondante, jusqu’à ce que le témoin

lumineux à côté du cycle désiré, s’allume. Choisir

les options désirées en appuyant sur les touches.

Les voyants de signalisation pour le cycle choisi et

les options lumineux. Pour annuler une option

appuie le coussin encore.

Pour démarrer un cycle, fermer la porte jusqu’à ce

qu’elle se verrouille, puis appuyer une fois sur la

touche

START/Cancel (Mise en Marche/

Annulation). À la suite d’une pause, le remplissage

commence. Le décompte de l’afficheur (certains

modèles) clignote jusqu’à ce que l’on appuie sur

START/Cancel.

Remarque

• Si l’on n’appuie pas sur la touche START/Cancel

dans les 30 secondes suivant la sélection du

cycle, le lave-vaisselle s’arrête.

Le lave-vaisselle se souvient du dernier cycle choisi.

Il n’

st donc pas néce

aire de reprogrammer le

cycle à chaque fois. Pour mettre en marche le lave-

vaisselle avec le même cycle et les mêmes options

que ceux choisis lors du lavage précédent, il suffit

d’appuyer sur la touche

START/Cancel.

3. Pour annuler un cycle en cours de fonctionnement,

appuyer une fois sur la touche

START/Cancel. Le

lave-vaisselle procède à une vidange puis s’arrête.

Pour arrêter le lave-vaisselle sans qu’il ne commence

une vidange, appuyer deux fois sur la touche

ART/Cancel

. P

our empêcher de

s changements

non prévus de c

ycle ou d’

option, il n’

st plus

possible de changer ces sélections après 1 minute.

Remarque

• Si l’on appuie sur la touche de cycle select après le

« verrouillage » des commandes, le témoin lumineux

situé á côte du cycle sélectionné clignote trois fois.

Ajout d’un article oublié

Pour de meilleurs résultats de nettoyage, l’article oublié

devra être ajouté au début du cycle

1. Saisir la poignée de porte et déverrouiller la porte

sans l’ouvrir complètement. Tous les témoins lumineux

clignotent pour indiquer que le cycle est interrompu.

2. Attendre l’arrêt de la circulation d’eau.

3. Ouvrir la porte et ajouter l’article.

4. Fermer la porte et la verrouiller. Les témoins

lumineux ce

ssent de clignoter lorsque la porte est

correctement fermée. Après un court instant, le cycle

reprend automatiquement au point où il s’est arrêté.

Remarques

• Si la porte est ouverte pendant le fonctionnement

d’un cycle, il peut y avoir jusqu’à 3

0 seconde

d’

attente avant que l’

appareil ne se remette en

marche une fois la porte fermée.

• Il n’est pas recommandé d’interrompre le cycle de

lavage pendant une période prolongée.

Recommandations d’ordre

général

(Les caractéristiques des paniers

arient selon le modèle)

•

s ar

ticle

s peuvent être centrés derrière une tige de

retenue ou chargés en biais pour tirer le meilleur

parti possible de l’espace.

• Éviter de bloquer les bras gicleurs. Ne rien laisser

dépasser de

s paniers.

•

ourner le

s sur

face

s souillée

s vers le centre du lave-

vaisselle.

Pour obtenir les meilleurs résultats de lavage, observer

les directives suivantes pour déterminer la disposition

qui convient le mieux aux ar

ticle

s à laver

Chargement

Suite...

La page charge ...

Maytag MDB8951AWB - Jetclean II Series Fully Integrated Dishwasher Mode d'emploi

Marque: Maytag

Modèle: MDB8951AWB - Jetclean II Series Fully Integrated Dishwasher

Catégorie: Lave-vaisselle

Taper: Mode d'emploi

Ce manuel convient également à

MDB-9

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MDB8951AWB - Jetclean II Series Fully Integrated Dishwasher User guide

Maytag MDB8951AWB - Jetclean II Series Fully Integrated Dishwasher Mode d'emploi

Ce manuel convient également à

Maytag MDB8951AWB - Jetclean II Series Fully Integrated Dishwasher Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents