Kohler 99539-1WA Guide d'installation

Installation and Care Guide

Vanity

Français, page ″Français-1″

Español, página ″Español-1″

1216526-2-F

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Select 500 lb (227 kg)

load bearing 5/16″ lag bolts with a length to clear obstacles

in the wall and 5/16″ washers. Calculate proper lag bolt

length by adding the following: 1-1/2″ (38 mm) backing

material + wallboard thickness + back rail thickness.

IMPORTANT! Risk of product damage. Do not modify the vanity.

Doing so will compromise structural stability.

NOTICE: Siliconized acrylic caulk must be used to secure a sink or

countertop to the vanity. Do not use 100% silicone sealant which

will damage the ﬁnish of the vanity.

NOTICE: Any electrical accessory components must be connected

to a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI)

or Residual Current Device (RCD). Follow all local electrical codes.

Your product may appear different than the one illustrated. The

installation procedures remain the same.

Observe all local building codes.

Two people should install this product.

Secure the vanity to stud framing. When possible, provide 2x6

bracing behind the ﬁnished wall for additional support.

This vanity is designed to allow most base moldings to pass

behind the vanity.

To ease installation, remove drawers from the vanity before

beginning. Refer to the section in this guide for proper removal.

Plus:

• Wood Screws

• 2x6s, 2x4s (Optional)

• 5/16" Lag Bolts and Washers

[Min 500 lb (227 kg) Load Bearing]

• Socket Wrenches

• Side Cutters

1216526-2-F 2 Kohler Co.

1. Hardware Placement for K-99688

Measure and mark the dimensions for the hardware as shown

above.

Drill a 3/16″ (21 mm) hole at each marking.

Insert a screw through each hole from the inside. Count the

number of notches that appear from the other side.

Remove the screw. Using a pair of side cutters, cut the screw at

the appropriate notch. Repeat for all screws.

Insert a screw through each hole and align them with the

handles. Thread the screws into the handles.

Drawer Pull

Location

Door Pull

Location

1-1/2" (38 mm)

3"

(76 mm)

3" (76 mm)

2-1/8"

(54 mm)

3" (76 mm)

Centered

Side to Side

Kohler Co. 3 1216526-2-F

2. Hardware Placement for K-99686 and K-99689

Measure and mark the dimensions for the hardware as shown

above.

Drill a 3/16″ (21 mm) hole at each marking.

Insert a screw through each hole from the inside. Count the

number of notches that appear from the other side.

Remove the screw. Using a pair of side cutters, cut the screw at

the appropriate notch. Repeat for all screws.

1"

(25 mm)

Centered

Side to Side

4-5/8"

(117 mm)

K-99686 and K-99689

3" (76 mm)

4-5/8"

(117 mm)

K-99689

4-5/8"

(117 mm)

3" (76 mm)

4-1/4"

(108 mm)

1216526-2-F 4 Kohler Co.

Hardware Placement for K-99686 and K-99689 (cont.)

Insert a screw through each hole and align them with the

handles. Thread the screws into the handles.

Kohler Co. 5 1216526-2-F

3. Preparation

CAUTION: Risk of property damage. To properly support

the weight of the vanity and sink, secure to stud framing or

2x6 bracing behind the ﬁnished wall.

If installing 2x6 bracing, front-notch the studs 1-1/2″ (38 mm) to

ensure the bracing sits ﬂush against the studs. The bracing

should span the length of the vanity.

Plan for routing supply and drain piping for your desired sink

installation.

Plan for electrical service if installing the optional electrical strip.

Any electrical accessory components must be connected to a

circuit protected by a Ground-Fault Circuit-Interrupter (GFCI) or

Residual Current Device (RCD).

NOTICE: To ensure proper support and alignment: The ﬁnished

wall must be straight and plumb. The ﬂoor must be ﬂat and

perpendicular to the ﬁnished wall.

Complete the ﬁnished wall.

34-1/2"

(876 mm)

2x6

Bracing

Plan the plumbing

area for the sink.

Products May Vary

in Appearance

1216526-2-F 6 Kohler Co.

4. Install the Optional Legs

NOTE: To protect the ﬁnished surface of the vanity, perform

assembly tasks on a ﬂat, padded work surface.

NOTE: The right and left leg assemblies are identical.

Lay the vanity top down on a ﬂat, padded surface.

Position a leg assembly at each side of the vanity, aligned over

the pre-drilled holes.

Secure each leg assembly to the vanity using the screws provided.

With assistance, turn the vanity upright to rest on its legs.

Screws

Kohler Co. 7 1216526-2-F

5. Secure the Vanity

CAUTION: Risk of property damage. Select 500 lb (227 kg)

load bearing 5/16″ lag bolts with a length to clear obstacles

in the wall and 5/16″ washers. Calculate proper lag bolt

length by adding the following: 1-1/2″ (38 mm) backing

material + wallboard thickness + back rail thickness.

CAUTION: Risk of product damage. Drill the lag bolt pilot holes

in the ends of the back rail to provide maximum support and to

prevent ﬂexing of the unit.

Wall-hung vanity only: Using 2x4 lumber, create a temporary

support that is 14-3/4″ (375 mm) in height and spans the width

of the vanity.

With assistance, lift and place the vanity in position against the

ﬁnished wall.

Verify the vanity is level and plumb against the wall.

Wall-hung vanity only: Place shims under the temporary support

to adjust the unit as needed.

Vanity with legs only: Turn the leveler(s) to adjust the unit as

needed.

Using a 1/4″ drill bit, drill a pilot hole at each end of the back

rail and into the ﬁnished wall. The holes should align with the

2x6 bracing or stud framing.

Drill a pilot hole at each stud location between the two end holes.

Washer

Lag Bolt

Back Rail

Temporary Support

(For Wall-Hung)

Leveler

Position lag bolts at ends of back rail

and secure into bracing.

2x6 Bracing

Pilot Hole

1216526-2-F 8 Kohler Co.

Secure the Vanity (cont.)

Secure the vanity to the wall with 5/16″ lag bolts and washers

(not provided). The lag bolts should engage the 2x6 bracing

and/or all studs behind the rail.

If used, remove and discard the temporary support once the

vanity is properly installed.

Install optional accessories (shelves, drawers, other) as desired.

Refer to the instructions packed with the accessories.

Kohler Co. 9 1216526-2-F

Adjust the Door

The hinges can be adjusted for proper door functionality and

alignment.

Refer to the illustration and note the screwdriver location for the

desired adjustment.

1216526-2-F 10 Kohler Co.

Remove the Door

Removal

With one hand, support the door in the open position.

Starting with the bottom hinge, press the latch at the end of the

hinge to release it from the bracket.

Repeat for the upper hinge.

Move the door forward to slide the hinges off the brackets.

Reinstallation

With one hand, support the door in the open position.

Starting with the top bracket, align the hinge pin with the cup of

the bracket.

Press the back of the hinge to snap the latch onto the bracket.

Repeat for the lower hinge.

Open and close the door to ensure proper operation.

Latch

Remove Reinstall

Cup

Kohler Co. 11 1216526-2-F

Remove/Adjust the Drawer

Alignment

To adjust the height and level the drawer, move the tabs

underneath the front corners back or forward as needed.

For ﬁne adjustment, loosen the screws behind the drawer face,

then hold the drawer face level while retightening the screws.

Removal

Fully extend the drawer.

From underneath, press the release latches toward the sides of the

drawer.

Lift the front of the drawer to disengage from the rails.

Reinstallation

Fully extend the rails.

Align the holes in the back of the drawer with the rail hooks.

Rotate the drawer down onto the rails, engaging the latches with

the rails.

Push the drawer closed to fully engage the latches.

To ensure the drawer is properly engaged, lightly lift the front of

the drawer. If not engaged, repeat the ″Reinstallation″ procedure.

Hole

Rail

Tab

Screw

Bottom

of Drawer

1216526-2-F 12 Kohler Co.

Care and Cleaning

For best results, keep the following in mind when caring for your

KOHLER product:

•

Blot spills immediately with a soft, damp cloth.

•

Test cleaners in a discrete location ﬁrst, such as the inside of a

door, to ensure that there is no adverse reaction.

•

Do not expose wood furniture to direct sunlight, drying heat

sources, or dampness.

•

Protect wood surfaces by using felt, leather or cork under

accessories. Never slide objects across wood surfaces.

•

Dust frequently with a soft cloth in the direction of the grain.

•

Use only products speciﬁcally made for cleaning wood. Avoid

using oily polishes or waxes, or products containing silicone.

•

Every six months, remove soil buildup by rubbing with a soft

cloth dampened in a 50/50 solution of warm water and an

ammonia-free detergent. Wipe clean with a cloth dampened in

warm water. Wipe dry.

•

Paint pens and touch-up markers are available to conceal

scratches on the wood surface. These products may be purchased

from a Kohler distributor or call 1-800-4-KOHLER for ordering

information.

For detailed cleaning information and products to consider, visit

www.kohler.com/clean. To order Care & Cleaning information, call

1-800-456-4537.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in

material and workmanship for one year from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate

adjustment where Kohler Co. inspection discloses any such defects

occurring in normal usage within one (1) year after installation. Kohler

Co. is not responsible for removal or installation costs. Use of in-tank

toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your

Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing

Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler,

Kohler Co. 13 1216526-2-F

Warranty (cont.)

WI 53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from

within the USA and Canada, and 001-800-456-4537 from within Mexico,

or visit www.kohler.com within the USA, www.ca.kohler.com from

within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE

DURATION OF THIS WARRANTY. KOHLER CO. AND/OR

SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states/provinces do not

allow limitations on how long an implied warranty lasts, or the

exclusion or limitation of special, incidental or consequential damages,

so these limitations and exclusions may not apply to you. This

warranty gives you speciﬁc legal rights. You may also have other

rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

1216526-2-F 14 Kohler Co.

Guide d’installation et d’entretien

Meuble de toilette

Outils et matériel

Avant de commencer

ATTENTION: Risque de dommages matériels. Choisir des

tire-fonds de 5/16″ porteurs de 500 lb (227 kg) avec une

longueur adéquate pour dégager les obstacles dans le mur,

ainsi que des rondelles de 5/16″. Calculer une longueur de

tire-fonds adéquate en ajoutant les valeurs suivantes:

matériau de renfort de 1-1/2″ (38 mm) + épaisseur de

panneau mural + épaisseur de rail arrière.

IMPORTANT! Risque d’endommagement du produit. Ne pas

modiﬁer le meuble de toilette. Ceci pourrait compromettre la

stabilité structurelle.

AVIS: Du mastic à l’acrylique siliconisé doit être utilisé pour

sécuriser un lavabo ou un comptoir sur le meuble. Ne pas utiliser de

mastic à la silicone à 100%, car cela endommagera la ﬁnition du

meuble.

AVIS: Tous les composants électriques doivent être raccordés à un

circuit protégé par un disjoncteur de fuite de terre (GFCI) ou à un

dispositif de protection à courant résiduel (RCD). Respecter tous les

codes électriques locaux.

Plus:

• Vis à bois

• 2x6, 2x4 (Optionnels)

• Tire-fond 5/16" et rondelles

[Porteur min 500 lb (227 kg)]

• Clés à douille

• Couteaux latéraux

Kohler Co. Français-1 1216526-2-F

Avant de commencer (cont.)

Le produit en question peut être différent de celui qui est illustré.

Les procédures d’installation restent les mêmes.

Respecter tous les codes de construction locaux.

Deux personnes doivent installer ce produit.

Fixer le meuble de toilette sur l’ossature. Lorsque possible, fournir

une entretoise 2x6 à l’arrière du mur ﬁni pour fournir un support

supplémentaire.

Ce meuble de toilette est conçu pour permettre à la plupart des

moulures de base de passer derrière le meuble de toilette.

Pour faciliter l’installation, retirer les tiroirs du meuble de toilette

avant de commencer. Se reporter à la section dans ce guide pour

une dépose appropriée.

1216526-2-F Français-2 Kohler Co.

1. Pose de visserie pour le modèle K-99688

Mesurer et marquer les dimensions pour la visserie comme sur

l’illustration ci-dessus.

Percer un trou de 3/16″ (21 mm) au niveau de chaque repère.

Enﬁler une vis par chaque trou à partir de l’intérieur. Compter le

nombre d’encoches visibles à partir de l’autre côté.

Retirer la vis. Couper la vis à l’encoche appropriée en utilisant un

couteau latéral. Répéter pour toutes les vis.

Insérer une vis à travers chaque trou et les aligner sur les

poignées. Visser les vis dans les poignées.

Emplacement de

bouton de tiroir

Emplacement de

bouton de porte

1-1/2" (38 mm)

3"

(76 mm)

3" (76 mm)

2-1/8"

(54 mm)

3" (76 mm)

Centré

Côte à côte

Kohler Co. Français-3 1216526-2-F

2. Pose de visserie pour les modèles K-99686 et K-99689

Mesurer et marquer les dimensions pour la visserie comme sur

l’illustration ci-dessus.

Percer un trou de 3/16″ (21 mm) au niveau de chaque repère.

Enﬁler une vis par chaque trou à partir de l’intérieur. Compter le

nombre d’encoches visibles à partir de l’autre côté.

Retirer la vis. Couper la vis à l’encoche appropriée en utilisant un

couteau latéral. Répéter pour toutes les vis.

1"

(25 mm)

4-5/8"

(117 mm)

K-99686 and K-99689

3" (76 mm)

4-5/8"

(117 mm)

Centré

Côte à côte

K-99689

4-5/8"

(117 mm)

3" (76 mm)

4-1/4"

(108 mm)

1216526-2-F Français-4 Kohler Co.

Pose de visserie pour les modèles K-99686 et K-99689 (cont.)

Insérer une vis à travers chaque trou et les aligner sur les

poignées. Visser les vis dans les poignées.

Kohler Co. Français-5 1216526-2-F

3. Préparation

ATTENTION: Risque de dommages matériels. Pour

supporter le poids du meuble de toilette et le lavabo de

manière appropriée, ﬁxer sur le pan à colombages ou

l’entretoise 2x6 à l’arrière du mur ﬁni.

Lors de l’installation d’une entretoise 2x6, placer un cran de

1-1/2″ (38 mm) à l’avant des montants aﬁn d’assurer que

l’entretoise est à ras de ces montants. L’entretoise doit s’étendre

sur la longueur du meuble de toilette.

Prévoir l’acheminement des tuyaux d’arrivée et d’évacuation pour

l’installation de lavabo souhaitée.

Prévoir le service électrique si une plaquette de connexions

électriques est installée. Tous les composants électriques doivent

être raccordés à un circuit protégé par un disjoncteur de fuite de

terre (GFCI) ou à un dispositif de protection à courant résiduel

(RCD).

AVIS: Pour assurer un support et un alignement appropriés: Le

mur ﬁni doit être droit et d’aplomb. Le plancher doit être plat et

perpendiculaire au mur ﬁni.

Terminer la ﬁnition murale.

34-1/2"

(876 mm)

Entretoise 2x6

Prévoir la zone de

plomberie pour

l'évier.

L'apparence des

produits peut varier.

1216526-2-F Français-6 Kohler Co.

La page charge ...

Kohler 99539-1WA Guide d'installation

Kohler 99539-1WA Guide d'installation

dans d''autres langues

Documents connexes