Risco WatchOUT Guide d'installation

Portuguese Français Español Italiano

English

Dual Technology Outdoor Detector

Rivelatore da Esterno a Doppia Tecnologia

Detector Externo de Doble Tecnología

Détecteur extérieur à double technologie

Detector Externo de Dupla Tecnologia

Installation Instructions - Relay & BUS Modes

Istruzioni per l’installazione in modalità Relé e BUS

Instrucciones de Instalación - Modos Relé y BUS

Guide d'installation - Modes Relais et BUS

Instruções de Instalação - Modos Relé & BUS

2 WatchOUT DT Installationn Manual

WatchOUT DT Installation Manual 3

English

Table Of Contents

Relay Mode Installation ............................................................................................................ 4

Introduction ...............................................................................................................................4

Mounting....................................................................................................................................4

Mounting Considerations........................................................................................................ 4

Wall Mount Installation............................................................................................................ 5

Flat Mounting:......................................................................................................................... 5

45° angle Mounting (Left side mounting)................................................................................ 5

Changing Back Tamper position............................................................................................. 6

Terminal Wiring ........................................................................................................................ 6

DIP Switch Settings....................................................................................................................7

Microwave Adjustment ............................................................................................................. 7

Walk test.................................................................................................................................7

LEDs Display .............................................................................................................................. 7

Relay Mode / BUS Mode Jumper............................................................................................. 7

Standard Swivel Installation .................................................................................................... 8

Wall Mounting......................................................................................................................... 8

Swivel Conduit Mounting (using Conduit

Metal Swivel Adaptor – CSMA, Figure 6, Detail A) ................................................................ 8

Replacing a Lens ..................................................................................................................... 10

Lenses Types ....................................................................................................................... 11

Technical Specification ........................................................................................................... 12

Ordering Information ............................................................................................................. 12

BUS Mode Installation ............................................................................................................ 13

Introduction ............................................................................................................................. 13

Terminal Wiring ...................................................................................................................... 13

DIP Switch Settings..................................................................................................................13

ProSYS Programming.............................................................................................................. 14

New System Parameters......................................................................................................... 16

4 WatchOUT DT Installation Manual

Relay Mode Installation

Introduction

RISCO Group's Dual Technology Outdoor detector, WatchOUT, is a unique detector with signal

processing based on two Passive Infrared (PIR) channels and two Microwave (MW) channels.

The detector can operate as a regular relay detector connected to any control panel, or as a BUS

accessory when connected to RISCO Group's ProSYS control panel via the RS485 BUS, thus

having unique remote control and diagnostic capabilities.

The instructions describe herein, describe the WatchOUT in Relay & BUS mode.

Mounting

Mounting Considerations

If possible, avoid pointing the detector to

moving objects (swaying trees, bushes etc.)

1m - 2.7m

(3'3" - 8'9")

Optional Height: 1m – 2.7m

(3'3"-8'9")

Typical Height: 2.2m (7'2")

Default Lens: Wide angle 15m (50') 90°

(RL300)

Note:

1. For low installations, below 1.7m (5'6") in which

pet immunity is required, use the supplied

RL300F lens (low wall or fence installations).

2. The detector's pet immunity (height of an animal,

no weight limitation), is up to 70 cm (2'4"), when

installing the detector at 2.2m (7'2"). If the

installation is bellow the height mentioned

above, the Pet Immunity decreases accordingly;

every 10 cm (4") decrease in installation height

leads to 10 cm (4") decrease in pet imunity.

Out of

Detection Range

Keep distance of

minimum 5m (16')

from moving objects

5m (16')

Ensure any objects do not obstruct the field of

view for both technologies. Pay attention to

growing trees or bushes, plants with big

moving leaves etc

For installations with extensive vehicle traffic or targets beyond

the required detection range, it is recommended to adjust the

MW sensitivity and/or to tilt the detector down.

Note:

Tilting the detector down may reduce the pet immunity

For optimum detection, select a

location that is likely to

intercept an intruder moving

across the coverage pattern at

a 45° trajectory.

WatchOUT DT Installation Manual 5

English

Wall Mount Installation

Figure 1

C1

Figure 2

I1

Figure 3

Tamper

Lever

A

T5

T1

B2

W9

B3

W2

B

L1

T3

B1

L2

W3

B4

R1

R2

(not visible)

T2

T6

(not visible)

T4

W5

W6

Note:

The installation knockouts numbering are marked on

the back plate.

1. Open WatchOUT front cover

(unlock C1, Figure 1).

2. Release internal base (unlock I1, Figure 2).

3. Select mounting installation as follows:

Flat Mounting:

Open knockouts on external base (Figure 3).

• B1 - B4: Wall mounting knockouts

• T1: Back tamper knockout

• W2 / W3: wires entry knockouts

45° angle Mounting (Left side

mounting)

a. Open knockouts on external base

(Figure 3)

• L1, L2: Left mounting knockouts

• T3: Left tamper knockout

• W5 / W6: Wire entry knockouts

b. Remove tamper spring.

c. Replace tamper bracket (Item 1) with

supplied flat tamper bracket (Item 2).

Item 1

Item 2

d. Insert Tamper lever B onto T5 and T3

and secure screw A (Figure 3).

4. Insert external wires through external base

W2, W3 (Flat Mounting) or W5, W6 (Left

side mounting) (Figure 3).

5. Secure external base to the wall.

6. Insert external wires and tamper wires

through internal base (Figure4).

7. Secure internal base to external base (lock

I1, Figure2).

8. Close the front cover (Lock C1, Figure1)

after wiring and setting DIP switches.

9. Walk test the detector.

Figure 4

Note:

For 45° right side installation use the equivalent units on the external base as follows:

Knockouts Description Left Right

Mounting Knockouts L1, L2 R1, R2

Tamper spring knockouts T1,T3 T2,T4

Tamper screw anchor T5 T6

Wiring Knockouts W5, W6 W7, W8

6 WatchOUT DT Installation Manual

Changing Back Tamper position

The back tamper is by default secured on the right

side of the internal base (rear view). If you wish to

move it to the left side (rear view), do the following

(Figure 5):

1. Remove tamper screw 1 in order to release the

tamper from position 7.

2. Ensure tamper spring 2 rests over tamper wire

base 4.

3. Ensure plastic tamper bracket 3 rests over both

2 and 4.

4. Secure tamper screw 1 into 3 over position 6.

Figure 5

Left Side

Tamper

Right Side

Tamper

3

6

1

2

4

7

5

Notes:

1. Verify that you hear a "Click" when attaching the tamper spring to the wall.

2. For pole installation, the tamper can be moved to the bottom right-hand side of the internal base.

Terminal Wiring

+-

SET/

UNSET

LEDs

ENABL

AM

YEL

FREE

ALARM

TAMPER

GREEN

FREE

DUST TEST

12VDC

N.C

WatchOUT DT - PCB

+,-

12 VDC

ALARM

N.C relay, 24VDC , 0.1A

FREE YEL

This terminal is a free pin that can be used to connect wires and EOL resistors

TAMPER

N.C relay, 24VDC , 0.1A

FREE

GREEN

This terminal is a free pin that can be used to connect wires and EOL resistors

AM

Normally closed AM relay output (

24VDC, 0.1A) indicates Anti Masking alarm or

any trouble in the detector (Not including dust/dirty lens).

Note:

When a vibration detector is installed and DIP8 is defined as Enabled this relay also opens

momentarily when vibration event occurs.

LED

ENABLE

Used to remotely control the LEDs when DIP1 is set to ON.

Enable: input is +12V OR no terminal connection

Disable: Connect the input to 0V

DUST

N.O. collector max 70 mA. Indicates that the lens is dirty and requires cleaning.

TEST

Used to perform remote alarm testing to the detector by applying 0 volts to this

terminal.

Success: Alarm relay is momentary opened.

Failure: AM relay is opened

This input enables to control Anti-masking and LEDs operation in accordance to

the system status, Set (Arm) / Unset (Disarm).

While the system is armed this feature prevents an intruder from gaining

knowledge of the detector’s status and disables Anti-masking detection.

SET/

UNSET

System Status Input Status AM Relay LEDs

Set (Arm) 0V Off Off

Unset (Disarm) 12V or no connection On* On**

* DIP7 is ON (Anti masking enabled)

** DIP1 is ON (LEDs enabled) and LEDs ENABLE input terminal is enabled

(+12V OR no terminal connection)

WatchOUT DT Installation Manual 7

English

DIP Switch Settings

12345678

ON

Factory

Default

DIP 1: LEDs operation

On: LEDs Enabled

Off: LEDs Disabled

DIP 2-3: Detection Sensitivity

Sensitivity DIP2 DIP3

Low Off Off

Mid Off On

Normal

(Default)

On Off

Maximum* On On

* In maximum sensitivity sway

recognition is disabled to achieve

maximum sensitivity

DIP 4: Alarm condition

On: PIR or MW

Off: PIR + MW

DIP 5: Detector's optics

On: Barrier / Long range

Off: Wide angle

DIP 6: Red LED /3 LED

On: Red LED only

Off: 3 LEDs

DIP 7: Anti masking operation

On: Enabled

Off: Disabled

DIP 8: Vibration detection (applicable to versions

with Vibration sensor installed)

On: Enabled

Off: Disabled

Microwave Adjustment

Adjust Microwave coverage area by using the trimmer on the PCB.

MIN

MAX

Walk test

Two minutes after applying power, walk test the protected area to

verify proper operation.

For installations on uneven surfaces slide the PCB inside the internal

base to the appropriate setting according to the desired height (1.0m,

1.5m, 2.2m, 2.7m) as printed on the bottom left corner of the PCB or

use the standard swivel accessory.

For reducing the detection range, slide the PCB up

or tilt the

swivel down

.

1.00M

1.50M

2.20M

2.70M

PCB

LEDs Display

LED State Description

Steady Indicates PIR detection

YELLOW

Flashing Indicates AM (Anti mask) detection

GREEN

Steady Indicates MW detection

Steady Indicates ALARM

RED

Flashing Indicates malfunctioned communication with ProSYS (BUS

mode only)

All LEDs

Flashing (One

after another)

Unit initialization on power up

Notes:

1. DIP-Switch 1 should be in ON position to enable LED indications.

2. Only one LED is active at any one time. For example, in the case of both PIR and MW detection, either the

steady YELLOW LED or the steady GREEN LED is displayed (the first to detect), followed by the Alarm RED

LED.

Relay Mode / BUS Mode Jumper

J-BUS jumper (located on the PCB between the red and green LEDs)

is used to define the detector’s mode of operation as follows:

Relay

Mode

BUS

Mode

8 WatchOUT DT Installation Manual

Standard Swivel Installation

The Outdoor detector packaging contains a standard swivel for flexible installation. Please follow

the instructions below for mounting the detector with the Standard Swivel:

1. Open WatchOUT front cover (Unlock C1, Figure1).

2. Release internal base (Unlock I1, Figure 2).

3. Open knockouts on external base (Figure 6, Detail B)

• W1: Wires knockout

• S1,S2: Knockouts for securing external base to Standard Swivel

• S3: External base locking screw knockout

4. On the swivel accessory remove the required swivel cable wiring knockout S2, S7 or S9

(Figure 6, Detail A).

5. Remove back tamper from the internal base (see “Changing Back Tamper Position"

paragraph) and connect it to S5 (Figure 6, Detail A) on the Standard Swivel.

Note:

Ensure that you see the engraved UP mark on the upper front face of the swivel.

6. Select the mounting installation type as follows:

Wall Mounting

a. Insert external cable wiring through knockouts S2, S7 or S9 and extract them (including the

tamper wires) through the Swivel Wires Passage (Figure 6, Detail B).

b. Secure swivel to the wall through holes S1, S3, S6 and S8.

Swivel Conduit Mounting (using Conduit Metal Swivel Adaptor – CSMA, Figure 6, Detail A)

S1

S2

S3

S9

S8

S7 S6

S5

S4

Tamper

(see Detail C)

Swivel Wires

Passage

Tamper

Spring

Holes

Ø 21 mm

Ø 16 mm

CSMA

M1

M2

M3

M4

Detail A Detail B

S1

W1

S2

S3

Snaps

Standard Swivel

Detail C

Figure 6

Note:

The CSMA is required when wall external wiring is used and protection pipe is required. The CSMA should

be ordered separately - P/N RA300SC0000A.

a. Choose the direction upon which to mount the CSMA according to the required diameter:

16mm (0.63 inches) or 21mm (0.83 inches).

b. Insert conduit to the CSMA.

c. Secure CSMA to the wall through points (M1, M4).

d. Insert external cables and tamper wires from the conduit through the swivel wires

passage of the swivel (Figure 6, Detail A).

e. Secure swivel to the wall through holes S1, S3, S6 and S8.

WatchOUT DT Installation Manual 9

English

Note:

The Tamper spring S5 (Figure 7) should make contact with the wall through the tamper spring holes M2 or

M3 on the CSMA. Make sure to hear the tamper "Click" when connecting to the wall.

7. Insert tamper wires and external cable wiring from Standard Swivel through knockout W1 on

the external base (Figure 6, Detail B).

8. Connect the external base to the swivel using the dedicated snaps (Figure 7).

PCB

External Base

Internal Base

Angle Locking

Screw

(See Note 2)

See Detail A

Swivel to External Base

Connecting Screws

Detail A

Swivel Assy

Connecting Screw

(See Note)

Snaps

S1

W1

S2

S3

Figure 7

NOTE:

Do not open or close the Swivel Assy Screw since it is used for connecting the swivel parts only.

9. Secure external base to swivel with two screws fastened to knockouts S1 and S2 (Figure 7).

10. Insert the supplied angle locking screw from the external base through the angle locking screw

knockout S3 on the external base to the standard swivel (Figure 7).

11. Tilt and Rotate the Standard Swivel to the desired position. Once the Standard Swivel is in the

desired position, secure the angle locking screw.

12. Line up the internal base onto the external base. Insert all wiring cables through the internal

base.

13. Secure internal base to external base (Lock I1, Figure 2).

14. To readjust the Standard Swivel when the PCB is installed (Figure 7):

a. Bend down the black foam located below the RED LED on the PCB (enough to reach the

Swivel locking screw).

b. Use a Philips screwdriver to release the locking screw (see Figure 8).

c. Tilt and/or Rotate the Standard Swivel to the desired position.

d. Secure the angle locking screw.

Note:

When marks on the two movable parts are aligned (Figure 8), the Standard Swivel is in 0°

vertical /horizontal position. Each click from this position represents shifting of 5° in vertical / horizontal

position.

15. Close the front cover (Lock C1, Figure 1) and walk test the detector.

10 WatchOUT DT Installation Manual

NOTE:

The screw has to pass through External Base and locked to the swivel.

Figure 8

Replacing Lenses

1. Unlock the six screws that hold the lens holding sleeve from the back of the front cover.

2. To release the protective sleeve, gently push the lens from the external side of the front cover.

3. Disconnect the lens from the sleeve by gently pushing the lens clips that secure it to the

sleeve.

4. Replace the lens. Place the 4 clips of the lens into the matching holes on the sleeve.

5. Insert the protective sleeve back into place on the front cover. Pay attention to place the

sleeve over the sealing rubber.

6. Secure the 6 holding screws back to their place.

Lens Protecting

Sleeve

Sockets for

Lens Clips

Sleeve Locking

Screws

Lens Locking

Clips

Sealing Rubber

Front Cover

Locking Screw

WatchOUT DT Installation Manual 11

English

Lens Types

Wide angle lens (RL300) /

Low installation - Pet lens (RL300F) :

Top view

11

Feet

0

10

20

30 40 50

10

20

30

40

10

20

30

40

2468100121415

1

3

5

7

9

0

1

3

5

7

9

90°

Wide angle lens (RL300):

Side View

Typical

Installation

Height:

2.2m (7'2")

0

10

2468100121415

0

10

20

30 40 50

1

3

0

Feet

Meters

Feet

Low installation - Pet lens (RL300F) :

Side view

Feet

0

6

2468100121415

0

10

20

30 40 50

1

0

2

Meters

Feet

Typical

Installation

Height:

1.5m (5'3")

Note:

The detector's Pet Immunity (height of an animal, no weight limitation), is up to 70 cm (2'4"), when installing the

detector at 2.2m (7'2"). If the installation is bellow the height mentioned above, the Pet Immunity decreases

accordingly; every 10 cm (4") decrease in installation height leads to 10 cm (4") decrease in pet imunity.

Long range lens (RL300LR): Top view

2468100 12141618202223

0

10

20

30 40 50

60 70 75

1

0

1

0

3

Feet

Meters

Feet

5°

Barrier lens (RL300B): Top view

2468100121415

0

10

20

30 40 50

1

0

1

0

3

Feet

Meters

Feet

5°

Long range lens (RL300LR): Side view

0

10

1

3

0

2468100 12141618202223

Meters

0

10

20

30 40 50

60 70 75

Feet

Typical

Installation

Height:

2.2m (7'2")

Feet

Barrier lens (RL300B): Side view

2468100121415

0

10

20

30 40 50

Feet

Meters

0

10

1

3

0

Typical

Installation

Height:

2.2m (7'2")

Feet

12 WatchOUT DT Installation Manual

Technical Specification

Electrical

45mA at 12 VDC (Stand by) Current consumption (Relay Mode)

70mA at 12 VDC (MAX with LED ON)

30mA at 12 VDC (Stand by), Current consumption (BUS Mode)

55mA at 12 VDC (MAX with LED ON)

Voltage requirements 9 -16 VDC

Alarm contacts 24 VDC, 0.1A

AM contacts 24 VDC, 0.1A

Dust output Open collector 70mA max

Physical

Size:

LxWxD

220 x 115 x 123mm (8.7 x 4.5 x 4.85 in.)

Weight 0.632 Kg (1.4lb)

Environmental

RF immunity (30MHz to 2GHz): 40V/m

Operating/Storage temperature -30°C to 60°C (-22°F to 140°F)

Ordering Information

Standard Units

Part Number Description

RK315DT0000A WatchOUT DT 10.525GHz + Swivel

RK315DT00UKA WatchOUT DT 10.587GHz + Swivel

RK315DT00FRA WatchOUT DT 9.9GHz + Swivel

Note:

Each of the detectors contains a standard swivel and 3 replacement lenses (P/N engraved on the Lens) 1.7m

low installation pet (RL300F), long-range (RL300R) and barrier lens (RL300B).

Accessories Kits

Part Number Description Weight

RA300B00000A WatchOUT Barrier Swivel Kit 0.1 Kg (0.23 lb)

RA300P00000A WatchOUT Pole Adaptor Kit 0.25 Kg (0.55 lb)

RA300C00000A WatchOUT Conduit Adaptor Kit 0.6 Kg (1.27 lb)

RA300HS0000A WatchOUT Demo Housing - -

RA300SC0000A WatchOUT Swivel Metal Conduit Adaptor 1Kg (2.2 lb)

Camera Option

Part Number Description

RA300VC0001A WatchOUT Camera Cover Adaptor 1

RA300VC017NA NTSC Narrow Camera For WatchOUT

RA300VC053NA NTSC Wide Camera For WatchOUT

RA300VC053PA WatchOUT PAL Wide Camera kit

RA300VC017PA WatchOUT PAL Narrow Camera kit

RA300VPS100A WatchOUT 220V PAL Camera Power supply

RA300VPS200A WatchOUT 120V Camera Power supply

WatchOUT DT Installation Manual 13

English

BUS Mode Installation

Introduction

The information in this section relates to WatchOUT DT installation in BUS Mode only. Up to 32

BUS detectors can be installed on the ProSYS RS485 BUS, saving cabling time and enabling

remote control and diagnostics.

Terminal Wiring

+,-

Used for the connection of 12VDC power supply. Connect the (+) terminal to

the AUX RED and the (–) terminal to the COM BLK of the ProSYS terminals

YELLOW

Used for data communication with the ProSYS. Connect to the terminal to the

BUS YEL of the ProSYS

GREEN

Used for data communication with the ProSYS. Connect to the terminal to the

BUS GRN of the ProSYS

TAMPER

Used for the wiring for tamper detection, see below

LED

ENABLE

Used for the wiring for tamper detection, see below

Note:

All terminals that are not mentioned in the table above are unused.

Cover and Back Tamper

+

-

SET/

UNSET

LEDs

ENABLE

AM

YEL

FREE

ALARM

TAMPER

GREEN

FREE

DUST TEST

COM

BLK

BUS

GRN

YEL

BUS Mode:

Cover + Back tamper wiring

BACK

TAMPER (N.C)

ProSYS

Short

AUX

RED

Cover Tamper Only

+-

SET/

UNSET

LEDs

ENABLE

AM

YEL

FREE

ALARM

TAMPER

GREEN

FREE

DUST TEST

COM

BLK

BUS

GRN

YEL

BUS Mode:

Cover Tamper Wiring

ProSYS

Short

AUX

RED

Cover Tamper to Zone Input

+

-

SET/

UNSET

LEDs

ENABLE

AM

YEL

FREE

ALARM

TAMPER

GREEN

FREE

DUST TEST

COM

BLK

BUS

GRN

YEL

BUS Mode:

Cover Tamper to Zone Input

ProSYS

BUS

Short

Zone

COM

Z1 Z2

Zone

Input

AUX

RED

DIP Switch Settings

DIP Switch

Number

Description

1 - 5 Used to set the detector ID number. Set the ID number in the same way as for

any other ProSYS accessory (Refer to the ProSYS installation instruction

manual)

6 - 8 Not used

14 WatchOUT DT Installation Manual

WatchOUT ID: DIP Switches 1 - 5

ID 1 2 3 4 5 ID 1 2 3 4 5

01 OFF OFF OFF OFF OFF 17 OFF OFF OFF OFF ON

02 ON OFF OFF OFF OFF 18 ON OFF OFF OFF ON

03 OFF ON OFF OFF OFF 19 OFF ON OFF OFF ON

04 ON ON OFF OFF OFF 20 ON ON OFF OFF ON

05 OFF OFF ON OFF OFF 21 OFF OFF ON OFF ON

06 ON OFF ON OFF OFF 22 ON OFF ON OFF ON

07 OFF ON ON OFF OFF 23 OFF ON ON OFF ON

08 ON ON ON OFF OFF 24 ON ON ON OFF ON

09 OFF OFF OFF ON OFF 25 OFF OFF OFF ON ON

10 ON OFF OFF ON OFF 26 ON OFF OFF ON ON

11 OFF ON OFF ON OFF 27 OFF ON OFF ON ON

12 ON ON OFF ON OFF 28 ON ON OFF ON ON

13 OFF OFF ON ON OFF 29 OFF OFF ON ON ON

14 ON OFF ON ON OFF 30 ON OFF ON ON ON

15 OFF ON ON ON OFF 31 OFF ON ON ON ON

16 ON ON ON ON OFF 32 ON ON ON ON ON

ProSYS Programming

The following section describes the additional software programming options, added to the

ProSYS software, that concern the settings of the WatcOUT DT as a BUS detector. Up to 32 BUS

detectors can be added to the system (16 in ProSYS 16) and each of them comes at the expense

of a zone in the system.

It is recommend reading and fully understanding the ProSYS Installation and User Manuals,

before programming the WatchOUT

Notes:

The WatchOUT is compatible with the ProSYS software Version 4.xx and above.

The WatchOUT can be programmed via the U/D Software from UD Version 1.8 and above.

For maximum operation stability, it is best NOT to exceed a total of 300 meters (1000 feet) of wiring when

connecting the WatchOUT to the BUS.

Adding / Deleting the WatchOUT DT

The WatchOUT is part of a new accessory category, BUS zones. Therefore, Adding/Deleting the

WatchOUT is identical to any other accessory with the following exception:

Each BUS Zone Detector should be assigned to a Regular Zone.

Any BUS detector can be assigned to a physical wired zone or to a virtual zone.

Physical zone: Any zone on the ProSYS PCB (zones 1-8) or on a wired zone expander

(ZE08, ZE16).

Virtual zone: Any zone on a BUS zone expander defined as BZ08 or BZ16.

Notes:

Virtual BUS zones are cost effective. They enable to expand your system zones without adding physical zone

expanders.

The virtual BUS zone expander can be used only for BUS zone detectors.

To add a BUS zone expander select type BZ08 or BZ16 when adding a zone expander (Quick key [7][1][2]).

1. To Add / Delete the WatchOUT DT

1. From the installer menu enter the Add/Delete menu: Quick Key [7][1][9][5] for BUS Zones

detectors.

2. Use the

/ or / keys to position the cursor over the BUS Zone

ID number for which you want to assign (or delete) a detector.

Note:

Make sure that the detector's physical ID number is identical to the ID number you select during programming.

WatchOUT DT Installation Manual 15

English

3. Place the cursor on the TYPE field and use the / key to select ODT15 for the

WatchOUT DT detector.

4. Press

/ to confirm.

5. Repeat the process for the other BUS detectors.

2. Assigning the WatchOUT DT to a Zone

1. From the main installer menu enter Zones: One by One option (Quick key [2][1])

2. Select the zone number that you want to assign the BUS detector.

Note:

If you defined a BUS Zone Expander, select a zone number from the virtual zones (defined by the BUS zone

expander).

3. Define Partitions, Groups, Zone Type and Zone Sound.

4. In the Termination category select [5] BUS Zone followed by

/ .

The following display appears:

Z:001 LINK TO:

ID:01 TYPE=ODT15

Z:001 LINK TO:

ID:01 TYPE=ODT15

5. Select the BUS zone number to assign to the programmed zone. The type field will be

updated automatically when selecting the zone.

6. Press

/ . The loop response category is not applicable to a BUS zone and the

following display appears:

Z:001 RESPONSE:

N/A-BUS ZONE

Z:001 RESPONSE:

N/A-BUS ZONE

7. Press

/ , assign label and press / .

3. Configuring the WatchOUT DT Parameters

1. To access the WatchOUT settings option press [2][0][3] from the main installer menu. The

following display appears:

B-ZONE PRMS:

ZONE#=001 (M:ZZ)

B-ZONE PRMS:

ZONE#=001 (M:ZZ)

2. Select the zone that the BUS zone was assigned to and press

/ . You can

now program the WatchOUT parameters as follows:

Zones Miscellaneous: BUS Zone

Quick Keys Parameter Default

LEDS 3 LEDS [2][0][3][zzz]

[1]

Defines the LEDS operation mode.

Off [2][0][3][zzz]

[1][1]

Disables the LEDS operation.

Red Only [2][0][3][zzz]

[1][2]

Only the Red led will operate. This option is highly recommended to avoid the

possibility that the intruder will “Learn” the detector behavior.

3 LEDS [2][0][3][zzz]

[1][3]

All 3 LEDs will operate.

PIR Sensitivity Normal [2][0][3][zzz]

[2]

Defines the sensitivity of the detector(MW + PIR)

Sensitivity Options [2][0][3][zzz]

[2][1]..[4]

1) Low

2) Medium

3) Normal

4) High

MW Range Trimmer [2][0][3][zzz]

[3]

Defines the microwave channel range. The maximum is 23m.

16 WatchOUT DT Installation Manual

Quick Keys Parameter Default

MW Range options [2][0][3][zzz]

[3][1]..[7]

1) Minimum

2) 20%

3) 40%

4) 60%

5) 80%

6) Maximum

7) Trimmer (MW is defined

by the trimmer setting on

the PCB)

Alarm Logic PIR and Microwave

[2][0][3][zzz]

[4]

Determine the detector’s logic of defining an alarm.

PIR and Microwave

[2][0][3][zzz]

[4][1]

Alarm is activated when both PIR and MW channels detect an alarm

(AND Logic)

PIR or Microwave

[2][0][3][zzz]

[4][2]

An alarm is activated when either PIR or MW channels detect an alarm (OR

Logic)

Lens Type Wide Angle

[2][0][3][zzz]

[5]

Defines the actual Lens of the detector

Lens Type Options

[2][0][3][zzz]

[5][1]..[2]

1) Wide Angle 2) Barrier / Long Range

Anti-Mask Enable

[2][0][3][zzz]

[6]

Defines the operation of Anti Masking detection

Anti-Mask Options

[2][0][3][zzz]

[6][1]..[2]

1) Disable 2) Enable (Default)

Arm/Disarm No

[2][0][3][zzz]

[7]

Defines the operation of the LEDs anti masking detections while the detector

is armed

No

[2][0][3][zzz]

[7][1]

AM (Anti masking) is enabled

LEDs behave according to the LEDs parameter definition

Yes

[2][0][3][zzz]

[7][2]

AM (anti masking) is disabled

LEDs are disabled

System Parameters

System: System Control

Quick Keys Parameter Default:

AM=Tamper No [1][2][36]

Used to determine the operation of Anti Masking detection

Yes: Anti mask violation will activate tamper alarm.

No: Anti mask violation will be regarded as trouble event.

VBR=Tamper No [1][2][37]

Used to determine the operation of the vibration detection (applicable to

versions with Vibration sensor installed)

Yes: Vibration detection will activate tamper alarm.

No: Vibration detection will be regarded as trouble event.

WatchOUT DT Installation Manual 17

English

Diagnostics

The ProSYS enables you to test parameters that reflect the operation of the detector.

1. From the main user menu press

[4] to access the Maintenance menu.

2. Enter the Installer code (or sub-installer) and press

/ .

3. Press [9] [1] to for the BUS Zones diagnostic menu.

4. Enter the digit of the zone that you want to test and then press

/ . The system will

perform the diagnostics test and a list of test parameters will appear, as indicated in the table

below.

5. Use the keys

/ / to view the diagnostics test results.

User Menu: 4) Maintenance → 9) Diagnostic → 1) BUS Zone

Quick Keys Parameter

[4][9][1][zzz]

Detector Input Voltage: Display the input voltage of the detector.

PIR 1 Level: PIR channel 1 DC level. Range 0.1v - 4v

PIR 1 Noise Level: PIR channel 1 AC level. Range 0VAC (No noise) - 4VA

PIR 2 Level: PIR channel 2 DC level. Range 0.1v - 4v

PIR 2 Noise Level: PIR channel 2 AC level. Range 0VAC (No noise) - 4VA

MW 1 Level: MW channel 1 DC level Range 0.1v - 4v

MW 1 Noise Level

: MW channel 1 AC level (0VAC (No noise) - 4VAC)

MW 2 Level: MW channel 2 DC level Range 0.1v - 4v

MW 2 Noise Level: MW channel 2 AC level (0VAC (No noise) - 4VAC

18 WatchOUT DT Installation Manual

Manuale di installazione WatchOUT DT 19

Italiano

Indice Dei Contenuti

Installazione in modalità relé ................................................................................................. 20

Introduzione....................................................................................................................... 20

Installazione....................................................................................................................... 20

Considerazioni per l’installazione ......................................................................................... 20

Installazione a parete............................................................................................................ 21

Installazione piana................................................................................................................ 21

Installazione angolare di 45° (installazione a sinistra).......................................................... 21

Modifica della posizione del tamper antirimozione............................................................... 22

Cablaggio morsettiera.................................................................................................. 22

Predisposizione Microinterruttori ............................................................................ 23

Regolazione microonda ............................................................................................... 23

Prova di movimento ........................................................................................................... 23

Indicatori LED .................................................................................................................... 23

Ponticello Modalità Relé / BUS ................................................................................. 24

Installazione dello snodo standard........................................................................ 24

Installazione a parete............................................................................................................ 24

Installazione per tubo elettrico.............................................................................................. 24

Sostituzione delle Lenti................................................................................................. 27

Tipologie di Lenti................................................................................................................... 28

Caratteristiche Tecniche............................................................................................... 29

Informazioni per l’ordine ............................................................................................ 29

Installazione in modalità BUS ................................................................................................ 30

Introduzione....................................................................................................................... 30

Cablaggio morsettiera.................................................................................................. 30

Tamper Antiapertura e Antirimozione .............................................................................. 30

Solo Tamper Antiapertura................................................................................................ 30

Tamper Antiapertura ad un Ingresso di Zona .................................................................. 30

Predisposizione microinterruttori ............................................................................ 30

Programmazione ProSYS............................................................................................. 31

Aggiunta e Cancellazione del WatchOUT DT ...................................................................... 31

Configurazione dei parametri del WatchOUT DT................................................................. 32

Parametri di Sistema...................................................................................................... 33

20 Manuale di installazione WatchOUT DT

Installazione in modalità relé

Introduzione

Il rivelatore da esterno Doppia Tecnologia WatchOUT di RISCO Group è un dispositivo a

microprocessore che elabora i segnali rilevati tramite due canali all’infrarosso passivo (PIR) e due

canali a microonda (MW). Il rivelatore può funzionare come rivelatore tradizionale con uscite a

relé collegabili a qualsiasi centrale d’allarme, o come rivelatore indirizzato via BUS 485 collegato

ai sistemi ProSYS di RISCO. Quando viene collegato ai sistemi ProSYS, il rivelatore può essere

programmato e testato sia localmente che in remoto tramite tastiere LCD ProSYS e/o software di

Teleassistenza RISCO. Le istruzioni che seguono descrivono l’installazione e la configurazione

del WatchOUT sia in modalità Relé che via BUS. Per informazioni sul collegamento in modalità

BUS ProSYS, consultare il capitolo “

Installazione in modalità BUS”.

Installazione

Considerazioni per l’installazione

If Se possibile, evitare di direzionare l’unità

verso oggetti in movimento (alberi ondeggianti,

cespugli, ecc.)

1m - 2.7m

(3'3" - 8'9")

Altez installate: Grandangolo 15m 90°

(RL300)

Note:

1. Per altezze di installazione basse, al di sotto di

1.7m ove è richiesta l’opzione di

discriminazione animali, vanno utilizzate le lenti

RL300F (muri bassi o installazione su

recinzioni).

2. La discriminazione animali (altezza

dell’animale senza limiti di peso) arriva fino a

70 cm con il rivelatore installato a 2.2m. Se

l’altezza di installazione è al di sotto di 2.2

metri la discriminazione animali si riduce

proporzionalmente. Ogni 10cm in meno

rispetto a 2.2 metri corrispondeono 10 cm in

meno di altezza dell’animale discriminato.

Mantenere una distanza

di almeno 5m (16') da

oggetti in movimento

Fuori campo di

rilevazione

5m (16')

Assicurarsi che nessun oggetto ostruisca il

campo di rilevazione dell’unità sia per la

sezione a microonda sia per quella ad

infrarossi. Prestare attenzione alla crescita di

alberi, rami e ad eventuali altre piante che con

il tempo possono coprire l’area di rilevazione.

Per quelle installazioni vicino a strade ad intenso traffico di

veicoli o oggetti oltre l’area di rilevazione desiderata, si

consiglia di regolare la sensibilità della microonda (MW) e/o

inclinare il rivelatore verso il basso.

Nota:

Inclinando il rivelatore verso il basso è possibile che la funzione di

immunità agli animali si riduca.

Per una migliore rivelazione

selezionare una posizione di

installazione in modo che

l’eventuale intruso attraversi

l’area di copertura del rivelatore

con una traiettoria di circa 45°

rispetto allo stesso.

La page charge ...

Risco WatchOUT Guide d'installation

Risco WatchOUT Guide d'installation

dans d''autres langues

Documents connexes

Autres documents