Amana NFW5800HW Le manuel du propriétaire

Marque: Amana

Modèle: NFW5800HW

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Use and Care Guide

Guide d’utilisation et d’entretien

Para obtener acceso al

Manual de uso y

cuidado en español, o para

obtener información adicional acerca de

su producto, visite:

www.amana.com

Front-Loading Automatic Washer

Laveuse automatique à chargement frontal

If you have any problems or questions, visit us at www.amana.com

Pour tout problème ou toute question, consulter www.amanacanada.ca

W11156981B

W11156982B – SP

Designed to use only HE

High Efciency detergents.

Conçue pour l’utilisation

d’un détergent haute

efcacité seulement.

TABLE OF CONTENTS

WASHER SAFETY ........................................................ 3

ACCESSORIES ............................................................. 4

CONTROL PANEL AND FEATURES ........................... 5

CYCLE GUIDE .............................................................. 7

CHOOSING THE RIGHT DETERGENT ........................9

USING THE DISPENSERS ............................................ 9

USING YOUR WASHER ..............................................10

WASHER MAINTENANCE ..........................................14

TROUBLESHOOTING .................................................17

WARRANTY ................................................................. 26

ASSISTANCE OR SERVICE ........................ Back Cover

TABLE DES MATIÈRES

SÉCURITÉ DE LA LAVEUSE ......................................... 27

ACCESSOIRES .............................................................. 28

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES .............................................. 29

GUIDE DES PROGRAMMES ........................................ 32

CHOIX D’UN DÉTERGENT APPROPRIÉ ..................... 35

UTILISATION DES DISTRIBUTEURS ........................... 35

UTILISATION DE LA LAVEUSE .................................... 36

ENTRETIEN DE LA LAVEUSE ...................................... 40

DÉPANNAGE ................................................................. 43

GARANTIE ..................................................................... 55

ASSISTANCE OU SERVICE ................ Couverture arrière

WASHER SAFETY

ACCESSORIES

INSTALLATION & MAINTENANCE

ACCESSORIES

FACTORY CERTIFIED PARTS – these three

words represent quality parts and accessories

designed specically for your appliance.

Time tested engineering that meets

our strict quality specications.

FACTORY CERTIFIED PARTS

Accessories designed for your appliance:

Customize your new washer and dryer with the following

genuine Amana accessories. For more information on

options and ordering, call 1-800-843-0304 or visit us at:

www.amanaparts.com. In Canada, call 1-800-807-6777

or visit us at www.amanacanada.ca.

15" Pedestal

Color-matched pedestals

raise the washer and dryer to

a more comfortable working

height. The large drawer

provides convenient storage.

Stack Kit

If space is at a premium, the

stack kit allows the dryer to be

installed on top of the washer.

CONTROL PANEL AND FEATURES

NOTES:

■ Not all features and cycles are on all models.

■ If your model has a touch interface, the control panel features a sensitive surface that responds to a light touch of your nger. To

ensure your selections are registered, touch the control panel with your ngertip, not your ngernail. When selecting a setting or

option, simply touch its name.

■ If your model has physical buttons, make sure to press the button rmly.

■

At cycle completion, your setting and option choices will be remembered for the next cycle. However, if power to the washer is

lost, the settings and options will go back to the factory defaults.

Cycles

Cycles and settings vary by model.

POWER

Select to turn the washer on and off. Select to stop/cancel

a cycle at any time.

CYCLES

At each stage of the process, you may notice sounds or

pauses that are different from traditional washers.

Press to select a cycle for your load.

START/PAUSE

Touch and hold for 3 seconds until the light above START/

PAUSE comes on to start a cycle, or touch once while a

cycle is in process to pause it.

CYCLE STATUS DISPLAY

The CYCLE STATUS DISPLAY shows the progress of a cycle.

At each stage of the process, you may notice sounds

or pauses that are different from traditional washers.

Estimated Time Remaining

The Estimated Time Remaining shows the time required

for the cycle to complete. Factors such as load size,

modiers, options selected, and water pressure may affect the

time shown in the display. Tightly packed loads, unbalanced

loads, or excessive suds may cause the washer to lengthen

the cycle time as well.

Sensing

When START/PAUSE is touched the washer will chime,

indicating it is starting, and “Sensing” will display. The drum

will make a partial turn. The door will click one more time

when it locks.

Once the door has locked, the washer will start.

This sensing process will continue throughout the cycle. After

the load is sensed, the estimated time based on load size will

be displayed and water will be added. You may hear water

owing through the dispenser, adding detergent to the load.

The actual cycle time may be lengthened; however, the

display will continue to show the estimated time.

In the display, “Sensing” may blink once a second at various

times during the cycle, such as when the washer is reducing

extra suds.

Hold 3 sec for

Control Lock

DISPENSERS

Single Load Dispenser Drawer

The single load dispenser drawer gives you the

convenience of adding HE detergent, liquid chlorine

bleach, and liquid fabric softener to the wash load at the

proper time. See the “Using the Dispensers” section for

information on using the dispenser drawer.

High Efficiency (HE) detergent compartment

This compartment holds liquid or powdered HE detergent

for your main wash cycle, and automatically dispenses

detergent in the cycle.

Liquid fabric softener compartment

This compartment holds liquid fabric softener. It

automatically dispenses liquid fabric softener at the

optimum time in the cycle.

Liquid chlorine bleach compartment

This compartment automatically dilutes and dispenses

liquid chlorine bleach at the optimum time during the

rst rinse after the wash cycle. It cannot dilute powdered

bleach.

Washing

During the wash cycle, this will display to let you know

the cycle is in progress.

Presoak

This symbol will be displayed to let you know

a presoak is in progress.

Add Garment

When "Add Garment" is displayed, you may pause the

washer, open the door, and add items. Touch and hold

START/PAUSE to start the washer again.

Door Locked

The Door Locked symbol will display to

indicate that the door is locked and cannot

be opened without rst pausing or canceling the cycle.

Control Lock

When the Control Lock symbol is displayed,

the buttons are disabled. Touch and hold EXTRA

RINSE for 3 seconds to enable the buttons.

End

Once the cycle is complete, “End” will display. Remove

the load promptly for best results.

CYCLE MODIFIERS

When you select a cycle, its default settings will light up.

Touch to adjust cycle modiers on the washer before

touching START/PAUSE. Additional wash modiers or

options selected after touching START/PAUSE may not

activate.

Once a wash setting is selected, it is saved for the cycle

selected. To return to factory default cycle settings, unplug

washer for 30 seconds; then plug back in. See the "Cycle

Guide" for default cycle settings.

NOTE:

Some modiers

may increase or decrease the

estimated time remaining.

Temp

The recommended wash temperature is preset for

each cycle. Some preset temperatures can be changed.

You may select a different wash temperature based on

the level of soil and type of fabric being washed. For

best results, use the warmest wash water safe for your

fabric, following the garment label instructions. All wash

temperatures feature a cold rinse.

Spin

The recommended spin speed is preset for each cycle.

Some preset speeds can be changed.

■ Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

■ Slower spin speeds reduce wrinkling, but will leave

your load more damp.

Soil

The recommended soil level is preset for each cycle.

Some preset soil levels can be changed. For heavily

soiled and sturdy fabrics, select the Heavy Soil Level

setting. For lightly soiled and delicate fabrics, select the

Light Soil Level setting. Lower soil level settings will help

reduce tangling and wrinkling.

hold 3 sec for

Cycle Signal

hold 3 sec for

Control Lock

hold 3 sec for

FanFresh

hold 3 sec for

PreSoak

OPTIONS

You may add or remove options for each cycle. Not all

options can be used with all cycles, and some are preset

to work with certain cycles. Options vary by model.

UTILITY TOOLS

Clean Washer

Use this every 30 washes to keep the inside of your

washer fresh and clean. This cycle uses a higher water

level. Use with affresh

Washer Cleaner tablets or liquid

chlorine bleach to thoroughly clean the inside of your

washer. When using this cycle, the drum should be

empty. This cycle should not be interrupted. See the

“Washer Care” section.

Drain & Spin

This cycle removes excess water from the load or

special-care items washed by hand. Use this cycle

after a power failure. For some fabrics, you may choose

to set a slower spin speed.

CYCLE OPTIONS

Extra Rinse

Activate this option to add an extra rinse to most

cycles.

You can also touch and hold EXTRA RINSE

for 3 seconds to disable/enable the Control Lock.

Presoak (on some models)

Touch to add a Presoak time of your choice

to a wash cycle.

hold 3 sec for

Cycle Signal

hold 3 sec for

Control Lock

hold 3 sec for

FanFresh

hold 3 sec for

PreSoak

CYCLE GUIDE

Settings and options shown in bold are default settings for that wash cycle. For best fabric care, choose the cycle, options, and

settings that best t the load being washed. Always read and follow fabric care labels and laundry product instructions. Not all settings

are available with each cycle, and some options cannot be used together. Not all options are available on all models.

Load Size Recommendations

For best results, follow the load size recommendations noted for each cycle.

Small load: Fill the washer drum with 3–4 items, not more

than ¼ full.

Large load: Fill the washer drum up to about ¾ full.

Medium load: Fill the washer drum up to about ½ full. Extra-large load: Fill the washer drum, but make

sure clothes can tumble freely. For best results, avoid

packing tightly.

Items to wash

using default

cycle settings:

Cycle:

Wash

Temperature

Spin

Speed

Soil

Level:

Options: Cycle Details:

Normally soiled

cottons, linens,

sheets, and

mixed garment

loads

Normal Cold

Cool

Warm

Hot

Off

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

This cycle combines medium-speed

tumbling and an extra-high-speed spin.

This cycle is designed to provide the

most energy efciency.

Small loads of

2–4 lightly soiled

garments

Quick Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

For small loads (2–4 items) needed

quickly. This cycle combines high-

speed tumbling, a shortened wash

time, and an extra-high speed spin for

reduced drying times.

Lightly soiled

shirts, blouses,

trousers, pants,

and dresses

Wrinkle

Control

Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

This cycle combines low-speed

tumbling and medium-speed spin for

gentle fabric care and reduced

wrinkling.

Sturdy colorfast

fabrics and

heavily soiled

garments

Heavy

Duty

Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

Fast-speed tumbling and an extra-fast-

speed nal spin help provide optimal

cleaning and reduce drying times.

Bright or darkly

colored cottons,

linens, casual,

and mixed loads

Cold

Wash

Cold Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

This cycle uses a concentrated

detergent solution along with cold

water throughout the cycle to gently

lift out stains and care for fabrics.

Clothing,

bedding and

towels requiring

sanitization

Sanitize

with Oxi

Hot Off

Slow

Medium

Fast

Light

Normal

Heavy

Extra Rinse This cycle eliminates 99.99% of the

most common bacteria found in

clothes, sheets, and towels. Using the

highest wash temperature available and

adding a powdered Oxi product in the

drum ensures sanitization. Check

recommended wash temperature of

your items and use the amount of Oxi

recommended by the manufacturer.

Bacteria tested were K. pneumonia, P.

aureginosa, and S. aureus.]

Moderately

soiled cottons,

linens, sheets,

and mixed

garment loads

Regular Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

This cycle combines medium-speed

tumbling and an extra-high-speed spin.

Bright or darkly

colored cottons,

linens, casual

and mixed loads

Colors Cold Off

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

This cycle combines gentle tumbling

and soaking to protect colors and

provide a gentle cleaning.

*All temperature selections feature a Cold rinse.

Items to wash

using default

cycle settings:

Cycle:

Wash

Temperature

Spin

Speed

Soil

Level:

Options: Cycle Details:

Moderately

soiled white

fabrics and

garments

Whites Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

Uses a longer wash time with fast-

speed tumbling, extra rinsing, and an

extra fast-speed spin to provide optimal

cleaning and rinsing when bleach is

used.

Sturdy towels

and wash cloths

Towels Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

Provides fast-speed tumbling, longer

wash time, normal rinsing, and an extra

fast-speed spin to shorten drying time.

Sheer fabrics,

lingerie,

sweaters, and

lightly-soiled

shirts, blouses,

trousers, pants,

and skirts

Delicates Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

This cycle combines slow-speed

tumbling and slow-speed spin for

gentle fabric care and reduced

wrinkling.

Normally

soiled sheets,

pillowcases,

light blankets, or

throws

Bulky

Items

Cold

Cool

Warm

Hot

Off

Slow

Medium

Fast

Light

Normal

Heavy

PreSoak

Extra Rinse

The wash action of this cycle is

designed to keep large items from

tangling and balling up.

*All temperature selections feature a Cold rinse.

Government energy certications for models WFW8620H and WFW862CH were based on the REGULAR (WHAT TO WASH),

NORMAL (HOW TO WASH), FASTEST SELECTABLE SPIN SPEED, HOLDING “DRAIN & SPIN” for 3 SECONDS TO ACTIVATE TIMED

DRY (4 HOURS - 1 TIME ONLY), DRYING TEMPERATURE SETTING NON - SELECTABLE. The as–shipped defaults of REGULAR

(WHAT TO WASH), NORMAL (HOW TO WASH), WARM TEMP, SPIN SPEED FAST were not used for energy testing.

CHOOSING THE RIGHT DETERGENT

Use only High Efciency detergents. The package will be marked

“HE” or “High Efciency.” Low-water washing creates excessive

sudsing with a non-HE detergent. Using non-HE detergent

will likely result in longer cycle times and reduced rinsing

performance. It may also result in component malfunction and,

over time, buildup of mold or mildew. HE detergents should be

low-sudsing and quick-dispersing to produce the right amount

of suds for the best performance. They should hold soil in

suspension so it is not redeposited onto clean clothes. Not all

detergents labeled as High Efciency are identical in formulation

and their ability to reduce suds. For example, natural, organic,

or homemade HE detergents may generate a high level of suds.

If you use one of these and see a “SUD” error code appear in

the display, consider using a different HE detergent. Always

follow the detergent manufacturer’s instructions to determine the

amount of detergent to use.

Use only High Efciency (HE) detergent.

About Detergent Concentration

Today’s liquid HE detergents are concentrated. Most brands of

concentrated HE detergent will show the level of concentration

on the bottle.

However, if the detergent bottle does not give the concentration,

it can be easily calculated. Just divide the package size in uid

ounces by the number of loads. Then refer to the chart below to

nd the concentration.

If you do not get your desired cleaning results, try using a lower

concentration number. If you have excess suds, try using a higher

concentration number.

Concentration Number of ounces ÷ number of loads

2X 1.5–2.49 (44.4 mL–73.6 mL)

3X 0.9–1.49 (26.6 mL–44.1 mL)

4X 0.7–0.89 (20.7 mL–26.3 mL)

5X 0.5–0.69 (14.8 mL–20.4 mL)

6X 0.3–0.49 (8.9 mL–14.5 mL)

8X < 0.29 (8.6 mL)

USING THE DISPENSERS (varies by model)

1. For a single load, open the single load dispenser drawer at

the top left corner of the washer.

2. Add laundry products as described below.

3. Slowly close the dispenser drawer. Make sure it is

completely closed.

NOTES:

■

A small amount of water may remain in the single load

dispenser from the previous wash cycle. This is normal.

■

Add single-dose and Oxi-type boosters to the drum before

loading items. See the “Using Your Washer” section.

Adding HE detergent to dispenser

Adding detergent for a single load

Selector

HE detergent

compartment

Pour a measured amount of HE detergent into detergent

compartment. For powdered detergent, lift the selector

to the high position. For liquid detergent, push down the

selector to the low position.

Do not overll; adding too much detergent may cause

detergent to be dispensed into the washer too early.

Use only High Efciency

(HE) detergent.

Powdered detergent:

Lift the selector to the high

position. Add directly to the

compartment.

IMPORTANT:

■ Do not add single-dose laundry packet to dispenser

drawer.

Liquid detergent:

Push down the selector

to the low position. Add

directly to the compartment.

USING YOUR WASHER

First wash cycle without laundry

Before washing clothes for the rst time, add detergent to the

single-dose dispenser (see the “Using the Dispensers” section).

Choose Quick cycle and run it without clothes. Use only HE

detergent. This initial cycle serves to ensure the interior is clean.

1. Sort and prepare your laundry

Sort items by recommended cycle, water temperature, and

colorfastness. Separate heavily soiled items from lightly soiled.

Separate delicate items from sturdy fabrics. Treat stains promptly

and check for colorfastness by testing stain remover products on

an inside seam.

IMPORTANT:

■ Empty pockets. Loose change, buttons, or any small object

can plug pumps and may require a service call.

■ Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

■ Mend rips and tears to avoid further damage to items

during washing.

■ Turn knits inside out to prevent pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

■ Do not dry garments if stains remain after washing because

heat can set stains into fabric.

■ Always read and follow fabric care labels and laundry

product instructions. Improper usage may cause damage

to your garments.

2. Add laundry products, if desired

Single-dose laundry packets, Oxi-type boosters, color-safe

bleach, or scented crystals can be added to the drum prior to

adding laundry.

NOTE: Always follow manufacturer’s instructions.

3. Load laundry into washer

Place a load of sorted items loosely in the washer. Items need

to move freely for best cleaning and to reduce wrinkling and

tangling. Close the washer door by pushing it rmly until the latch

clicks.

■ Push load fully into the washer. Make sure no items are resting

on the rubber seal to avoid trapping them between the seal

and the door window.

■ Mix large and small items and avoid washing single items.

Load evenly.

■ Wash small items in mesh garment bags. For multiple items,

use more than one bag and ll bags equally.

4. Add HE detergent

Adjust the selector, based on type of HE detergent used

(either liquid or powdered). Add a measured amount of

detergent directly into the detergent compartment. See the

“Using the Dispensers” section.

Single load

powdered

HE detergent

Single load

liquid

HE detergent

Single Load Dispenser Drawer

NOTE: Do not add single-dose laundry packets, Oxi-type

boosters, color-safe bleach, or scented crystals to dispensers.

They will not dispense correctly.

Pour a measured amount of liquid fabric softener into liquid

fabric softener compartment. Always follow manufacturer’s

directions for correct amount of fabric softener, based on

your load size.

Fabric softener is always dispensed in the last rinse, even

if Extra Rinse is selected.

IMPORTANT: Do not overll, dilute, or use more than

the manufacturer-recommended quantity of fabric softener.

Do not ll past the “MAX” line. Overlling dispenser will

cause fabric softener to immediately dispense into washer.

■ Do not spill or drip any fabric softener onto the clothes.

■ Do not use liquid fabric softener dispenser balls in this

washer. They will not dispense correctly.

■ Do not use fabric softener sheets, as they can stain

the load.

5. Add liquid fabric softener to single

load dispenser, if desired

7. Touch POWER to turn on washer

8. Select a wash program/cycle

See the Cycle Guide for details on cycles features.

9. Adjust cycle modiers, if desired*

The led indicator lights will show the default settings for the

selected cycle. To adjust a setting, touch its name – Temp,

Spin, or Soil. Adjusting settings may change the Estimated

Time Remaining. Tightly packing the load, unbalanced loads,

or excessive suds may also cause the washer to increase the

cycle time.

10. Select any additional options*

Hold 3 sec for

Control Lock

To add an option to the cycle, touch its name – Extra Rinse. To

remove an option from the selected cycle, touch that button

again.

Add liquid chlorine bleach to the bleach compartment.

Do not overll, dilute, or use more than 2⁄3 cup (165 mL).

Do not use color-safe bleach or Oxi in the same cycle with

liquid chlorine bleach.

IMPORTANT:

■ Always measure liquid chlorine bleach. Use a measuring

cup with a pour spout; do not guess.

■ Do not ll beyond the “MAX” line. Overlling could

cause garment damage.

■ Do not use thickened, easy-pour, or no-splash bleach

when running the Clean Washer with affresh

cycle, as

excess suds may occur.

■ Do not add liquid chlorine bleach to the bulk dispenser.

■ Slowly close dispenser drawers. Make sure the drawers

are closed completely.

6. Add liquid chlorine bleach to

single load dispenser, if desired

* Not all options and settings are available with all cycles.

See “Cycle Guide” for available options and settings.

11. Touch and hold START/PAUSE

to begin wash cycle

Touch and hold START/PAUSE for 3 seconds to start the wash

cycle. To pause a cycle in progress, touch START/PAUSE once;

then touch and hold again to continue the cycle. To cancel a

cycle, touch and hold POWER.

Once you touch and hold START/PAUSE, you will hear the door

lock. The washer door will remain locked during the wash cycle.

Unlocking the door to add garments:

If you need to open the door to add one or two

missed garments, you may do so while the

“Add Garment” light is lit. The time allowed

to add a garment will vary based on cycle

selection and load size.

Touch START/PAUSE once; the door will unlock

once the washer movement has stopped.

This may take several minutes. Then close

door and touch and hold START/PAUSE again

to restart the cycle.

Adding items after “Add Garment” light is off:

Cancel current cycle. Water will drain and you will need

to reselect cycle and restart.

For best wash performance and optimal energy savings,

add garments only when the “Add Garment” light is on.

12. Remove garments promptly

after cycle is nished

Promptly remove garments after cycle

has completed to avoid odor and rusting of

metal objects on garments. When unloading

garments, pull back the door seal and check

for small items between the tub and the

washer drum.

NOTES:

■ A small amount of water may remain in the single load

dispenser after the wash cycle is complete. This is normal.

■ This washer has a tight seal to avoid water leaks. To avoid

odors, leave the door open to allow the washer to dry

between uses.

WASHER MAINTENANCE

Replace inlet hoses after ve years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses:

Mark the date of replacement on the label with a permanent

marker.

Check that the old washers are not stuck on the washer inlet

valves.

Use new washers in the new inlet hoses to ensure a proper seal.

WATER INLET HOSES

WASHER CARE

Recommendations to Help Keep Your Washer Clean and

Performing at Its Best

1. Always use High Efciency (HE) detergents and follow the

HE detergent manufacturer’s instructions regarding the

amount of HE detergent to use. Never use more than the

recommended amount because that may increase the

rate at which detergent and soil residue accumulate inside

your washer which, in turn, may result in undesirable odor.

2. Use warm or hot water washes sometimes (not

exclusively cold water washes) because they do a better

job of controlling the rate at which soils and detergent

accumulate.

3. Always leave the washer door slightly ajar between

uses to help dry out the washer and avoid the buildup

of odor-causing residue.

4. Periodically clean residue from all interior surfaces of the

glass window. For better care, wipe the entire inside of the

glass door with a damp cloth.

Cleaning Your Front Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This washer

maintenance procedure should be performed, at a minimum,

once per month or every 30 wash cycles, whichever occurs

sooner, to control the rate at which soils and detergent may

otherwise accumulate in your washer.

Cleaning the Door Seal

1. Open the washer door and remove any clothing or items

from the washer.

2. Inspect the gray-colored seal between the door opening

and the drum for stained areas or soil buildup or lint. Pull

back the seal to inspect all areas under the seal and to

check for foreign objects or lint.

3. If stained areas or soil buildup, or lint are found, wipe

down these areas of the seal using either of the following

two procedures:

a. affresh

Machine Cleaning Wipes Procedure:

i. When the cycle is complete, gently pull back the

rubber door seal and clean the entire surface with the

textured side of an affresh

Machine Cleaning Wipe.

b. Dilute Liquid Chlorine Bleach Procedure:

i. Mix a dilute bleach solution, using 3/4 cup (177 mL)

of liquid chlorine bleach and 1 gallon (3.8 L) of warm

tap water.

ii. Wipe the seal area with the dilute solution, using

a damp cloth.

WASHER CARE (cont.)

iii. Let stand 5 minutes.

iv. Wipe down area thoroughly with a dry cloth and let

washer interior air dry with door open.

IMPORTANT:

■ Wear rubber gloves when cleaning with bleach.

■ Refer to the bleach manufacturer’s instructions for

proper use.

Cleaning the Inside of the Washer

This washer has a special cycle that uses higher water

volumes in combination with affresh

Washer Cleaner or

regular liquid chlorine bleach to thoroughly clean the inside

of the washer. Steam washer models also utilize steam to

enhance cleaning in this special cycle.

IMPORTANT: Do not use thickened, easy-pour, or no-splash

bleach when running the Clean Washer with affresh

cycle as

excess suds may occur.

NOTE: Read these instructions completely before beginning

the cleaning process.

Begin procedure

1. Clean Washer with affresh

Cycle Procedure

(Recommended for best performance):

a. Open the washer door and remove any clothing

or items.

b. Use an affresh

Machine Cleaning Wipe or a soft,

damp cloth or sponge to clean the inside door window.

c. Add an affresh

Washer Cleaner tablet to the

washer drum.

d. Do not add the affresh

Washer Cleaner tablet to

the dispenser drawer.

e. Do not add any detergent or other chemical to the

washer when following this procedure.

f. Close the washer door.

g. Select the Clean Washer with affresh

cycle.

NOTE: The washer remembers your last option selection

and will use it for future wash cycles until you deselect

that option.

h. Touch and hold START to begin the cycle.

The Clean Washer with affresh

cycle operation

is described below.

2. Chlorine Bleach Procedure:

a. Open the washer door and remove any clothing

or items.

b. Open the single load dispenser drawer and add

regular liquid chlorine bleach to the "MAX" line in

both the bleach compartment and the fabric softener

compartment. Either traditional or HE chlorine bleach

can be used.

IMPORTANT: Do not use thickened, easy-pour,

or no-splash bleach as excess suds may occur.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

WASHER CARE (cont.)

c. Close the washer door and the dispenser drawer.

d. Do not add any detergent or other chemicals to the

washer when following this procedure.

e. Select the Clean Washer with affresh

cycle.

NOTE: The washer remembers your last option

selection and will use it for future wash cycles until

you deselect that option.

f. Touch and hold START/PAUSE to begin the cycle.

The Clean Washer with affresh

cycle operation

is described below.

NOTE: For best results, do not interrupt cycle.

Description of Clean Washer with affresh

Cycle

Operation:

1. The Clean Washer with affresh

cycle will determine

whether clothing or other items are in the washer.

2. If no items are detected in the washer, it will proceed with

the cycle.

a. If any items are detected in the washer, “rL”

(remove load) will be displayed. The door will unlock.

Open washer and remove any garments from the

washer drum.

b. Touch POWER to clear the “rL” code.

c. Touch and hold START/PAUSE to restart the cycle.

3. Steam models only: During the rst 20 minutes of the

cycle, it will activate the steamer but the drum will not

spin or ll with water. You may see condensation on the

door window during this initial phase. If you are using

an affresh

Washer Cleaner tablet, it will not dissolve

completely during the steam phase. This is normal.

After the cycle is complete, leave the door open slightly to

allow for better ventilation and drying of the washer interior.

Cleaning the Dispensers

After using the Clean Washer with affresh

cycle, you may

nd some residue buildup in the washer’s dispensers.

To remove residue from the single load dispenser, remove

the drawer and wipe the surfaces with an affresh

Machine

Cleaning Wipe or a damp cloth and towel dry either before

or after you run the Clean Washer with affresh

cycle. Use

an all-purpose surface cleaner, if needed.

Replace the dispenser in the washer cabinet and make sure

that it is correctly seated.

IMPORTANT: Dispensers are not dishwasher-safe.

Cleaning the Outside of the Washer

Use an affresh

Machine Cleaning Wipe or a soft, damp

cloth or sponge to wipe up any spills. Occasionally wipe the

outside of your washer to help keep it looking new. Use an

affresh

Machine Cleaning Wipe or mild soap and water.

IMPORTANT: To avoid damaging the washer’s nish, do not

use abrasive products.

CLEAN WASHER CYCLE REMINDER

NOTE: Not all models have the Clean Washer with affresh

cycle reminder light.

The Clean Washer with affresh

LED will ash at the end of a

wash cycle when the washer has run 30 wash cycles. This is

a reminder to run the Clean Washer with affresh

cycle.

If the Clean Washer with affresh

cycle is not turned on, the

LED will stop ashing at the end of a wash cycle after running

three more regular wash cycles. After 30 more wash cycles

are completed, the Clean Washer with affresh

LED will again

ash at the end of a wash cycle as a reminder.

REMOVING THE DISPENSER (cont.)

Removing the Dispenser

To remove:

1. Pull dispenser drawer out until it stops.

2. Press down on the release tab and pull straight out

to remove the dispenser.

3. Lift off cover panel

by pulling straight up.

To replace:

1. Position cover panel back

onto posts on dispenser

Apply slight pressure on

cover panel to seat it.

2. Align edges of dispenser

with guides in washer;

then slide dispenser

back into slot.

Single Load Dispenser Drawer

Operate your washer only when you are home. If moving

or not using your washer for a period of time, follow these

steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid ooding due

to water pressure surges.

HELPFUL TIP: Attach a reminder note to the washer

to turn the water back on before washer’s next use.

3. Clean the dispensers. See “Cleaning the Dispensers.”

NON-USE AND VACATION CARE

WINTER STORAGE CARE

IMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; then disconnect and drain

water inlet hoses.

HELPFUL TIP: Attach a reminder note to the washer

to turn the water back on before washer’s next use.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum

and run washer on Normal cycle for about 2 minutes

to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

“Winter Storage Care” directions before moving.

3. Disconnect drain hose from drain system and from back

of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer drum.

6. Bundle power cord with a rubber band or cable tie to

keep it from hanging to the ground.

IMPORTANT: Call for service to install new transport bolts.

Do not reuse transport bolts. Washer must be transported

in the upright position. To avoid structural damage to

your washer, it must be properly set up for relocation

by a certied technician.

REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

Refer to Installation Instructions to locate, level, and

connect washer.

Before using again, run washer through the following

recommended procedure:

To use washer again:

Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

Plug in washer or reconnect power.

Run washer through Heavy Duty cycle to clean washer

and remove antifreeze, if used. Use only HE detergent.

Use half the manufacturer’s recommended amount for

a medium-size load.

ADDITIONAL CLEANING

Gently pull back the rubber door seal and clean any stained

areas, soil buildup, or lint with the textured side of an

affresh

Machine Cleaning Wipe.

If you experience Possible Causes Solution

Error Code Appears in Display (for 2- and 3-digit displays)

Once any possible issues are corrected, touch POWER once to clear the code. Reselect and restart the cycle.

“Sd” or “SUD”

(excess suds) appears

in display

Excessive suds in washer. Washer

is running a suds reduction routine.

Allow the washer to continue. Use only HE detergent. Always

follow the detergent manufacturer’s instructions to determine

the amount of detergent to use, and base detergent quantity

on load size. Not all detergents labeled as High Efciency

are identical in formulation and their ability to reduce suds.

For example, natural, organic, or homemade HE detergents

may generate a high level of suds. If you use one of these and

see a “SUD” error code appear in the display, consider using

a different HE detergent.

“Lo” “FL” appears on

display, or F8 E1

“Lo” “FL” appears on

display, or F08 E01

(water supply error)

appears in display

Check for proper water supply. Unit will drain for 8 minutes while door remains locked. The

drain cycle must be allowed to complete, or the error code

cannot reset. When complete, touch POWER once to clear

the code. Then touch POWER again and restart the washer. If

code appears again, call for service.

Both hoses must be attached and have water owing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

If used, auto shut-off connectors and hoses must be properly

installed and in working order.

Check for proper inlet hoses. Use only manufacturer’s recommended inlet hoses.

F9 followed by E1

F09 followed by E01

(drain pump system error)

appears in display

Check for proper drain hose

installation.

Ensure top of drain pipe is installed at least 39" above the

oor. Ensure drain hose extends no farther than 4

⁄2" into

standpipe.

Check plumbing for correct drain

hose installation. Drain hose extends

into standpipe farther than 4

⁄2"

(114 mm).

Check drain hose for proper installation.

Make sure the drain hose is not kinked, pinched, or blocked.

Remove any clogs from drain hose.

Use drain hose form and securely attach to drainpipe or tub.

Lower drain hose if the end is higher than 96" (2.4 m) above

the oor.

Ensure drain hose extends no farther than 4

⁄2"into standpipe.

Not using HE detergent or using too

much HE detergent.

Use only HE detergent. Always measure detergent and follow

manufacturer’s directions based on load size and soil level.

F5 followed by E2 or

F05 followed by E02

(door will not lock)

appears in display

Washer door not locking. Touch POWER to cancel the cycle. Check that the door is

closed completely and latching. Check for items in the washer

drum that may be keeping the door from closing completely.

Err Invalid action performed. This error code will be shown in the following conditions:

1. Trying to start a cycle with the door open.

2. Trying to select a different cycle while you’re already

running one.

No further action is needed to correct this.

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.amana.com

(in Canada www.amanacanada.ca) for assistance and to possibly avoid a service call.

F# E# or F## E## code

other than as described

above appears in display

System error code. Touch POWER once to clear the code. Then touch POWER

again and restart the washer. If code appears again, call for

service. Unplug washer for 30 seconds; then plug back in.

Washer making error

beeps

Door has not been opened and

closed for at least three cycles.

This code may occur when the washer is rst turned on.

Open and close the door to clear the display.

Washer beeps when Start/

Pause is touched

Door not closed. Close the door completely.

CL appears on display, or

Clean Washer LED ashing

at end of wash cycle (on

some models)

The washer has run 30 wash cycles

and is indicating a reminder to run the

Clean Washer with affresh

cycle.

Run the Clean Washer with affresh

cycle. If the Clean Washer

with affresh

cycle is not turned on, the LED will stop ashing

at the end of a wash cycle after running three more regular

wash cycles. After 30 more wash cycles are completed, the

Clean Washer with affresh

LED will again ash at the end of

a wash cycle as a reminder.

Washer won’t start Control lock could be enabled. To check whether the unit is in control lock, try powering On

the unit. On doing that if you see the code ‘Loc’ displayed

in the seven segment display, then you know that control is

locked. To unlock controls press and hold the ‘control lock’

key for three seconds.

Be sure the door is closed.

Make sure you press and hold the start button for 1 full second.

Make sure the door has been opened and closed since the last

cycle was run.

“PF” Appears upon recovery from power

loss, if power was lost while running

a cycle.

Touch POWER once to clear the code. Then touch POWER

again and restart the washer.

F0 E5 or “ob” Off balance load detected. This

means that your washer detected an

off balance load and that caused the

cycle to take longer than usual or the

clothes to be more wet than usual.

Touch POWER once to clear the code. Then touch POWER

again and restart the washer.

“dr” or F5 E4 Door not opened between cycles. Open and close the door. Touch POWER once to clear the

code. Then touch POWER again and restart the washer.

TROUBLESHOOTING

If you experience Possible Causes Solution

Error Code Appears in Display (for 2- and 3-digit displays) (cont.)

“rL” (remove load) appears

in display

Load detected in drum during Clean

Washer with affresh

cycle.

Remove items from washer drum and restart Clean Washer

with affresh

cycle.

Loc Control is locked. This is not an error code but just an indication that the

control is locked. Press and hold the control lock key for

three seconds to unlock.

First try the solutions suggested here or visit our website at www.amana.com

(in Canada www.amanacanada.ca) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Vibration or Off-Balance

Vibration, rocking,

or “walking”

Feet may not be in contact with the

oor and locked.

Front and rear feet must be in rm contact with oor, and

washer must be level to operate properly. Jam nuts must

be tight against the bottom of the cabinet.

Washer may not be level. Check oor for exing or sagging. If ooring is uneven, a

3/4" (19 mm) piece of plywood under your washer will reduce

sound. Do not install washer on a raised wooden platform.

See “Level the Washer” in Installation Instructions.

Load could be unbalanced or too large. Avoid tightly packing the load. Avoid washing single items.

Balance a single item such as a rug or jeans jacket with a

few extra items.

Item or load not suitable for selected cycle. See “Cycle

Guide” and “Using Your Washer.”

The shipping bolts are still in the back

of the washer.

See “Remove transport bolts from washer” in the

Installation Instructions.

Noises

Clicking or metallic noises Door locking or unlocking. After starting a cycle the drum will make a partial turn and the

door will lock. The door will remain locked until the end of the

cycle. This is normal.

Objects caught in washer drain system. Empty pockets before washing. Loose items such as coins

could fall between washer drum and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal

snaps, buckles, or zippers touch against the stainless

steel drum.

Gurgling or humming Washer may be draining water. The pump may make a humming sound with periodic

gurgling or surging as nal amounts of water are removed

during the spin/drain cycles. This is normal at certain stages

of the cycle.

Rolling or sloshing

and occasional clicking

(on slow-speed spin)

Steel balls in the balancing system are

balancing the load.

This is normal at certain stages of the cycle.

Water Leaks

Check the following for

proper installation

Fill hoses not attached tightly. Tighten ll-hose connection.

Fill hose washers. Properly seat all four ll-hose at washers.

Drain hose connection. Check that the drain hose is properly secured to drainpipe

or laundry tub.

One some models: Drain pump lter is

not properly seated.

One some models: Make sure lter is correctly placed in

the housing. See “Cleaning the Drain Pump Filter/Draining

Residual Water.”

Check household plumbing for leaks

or clogged sink or drain.

Water can back up out of a clogged sink or drainpipe. Check

all household plumbing for leaks (laundry tubs, drain pipe,

water pipes, and faucets.)

Strainer (or nylon stocking) on end

of drain hose is clogged.

Remove strainer/stocking from drain hose.

First try the solutions suggested here or visit our website at www.amana.com

(in Canada www.amanacanada.ca) for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Water Leaks (cont.)

Water or suds leaking from

door or rear of cabinet

Not using HE detergent or using too

much HE detergent.

Only use HE detergent. Suds from regular detergents

can cause leaking from the door or rear of cabinet. Always

measure detergent and follow manufacturer’s directions based

on your load requirements.

Using thickened, easy-pour, or

no-splash bleach when running the

Clean Washer with affresh

cycle.

Use affresh

tablet or regular, non-thickened chlorine bleach

when running the Clean Washer with affresh

cycle.

Residue on door window. Periodically clean the underside of the window to avoid potential

leaks.

Door opened during

“Add Garment.”

Water can drip off the inside of the door when the door is opened

after the start of a cycle.

Leaking around door Hair, lint, or other debris on inner

door window preventing proper seal

with rubber door seal.

Clean inner door window and seal. See “Cleaning the Door Seal”

in the “Washer Maintenance” section.

Washer Not Performing As Expected

Load not completely

covered in water

Water level not visible on door

or does not cover clothes.

This is normal for an HE front-load washer. The washer senses

load sizes and adds the correct amount of water for optimal

cleaning.

Washer won’t run or ll;

washer stops working

Check for proper water supply. Both hoses must be attached and have water owing to the

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water ow.

Washer won’t run or ll;

washer stops working

(cont.)

Check proper electrical supply. Plug power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Do not plug into a GFCI (Ground Fault Circuit Interrupter).

Check electrical source or call an electrician to check if voltage

is low.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

First try the solutions suggested here or visit our website at www.amana.com

(in Canada www.amanacanada.ca) for assistance and to possibly avoid a service call.

La page charge ...

Amana NFW5800HW Le manuel du propriétaire

Marque: Amana

Modèle: NFW5800HW

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Amana NFW5800HW Owner's manual

Amana NFW5800HW Le manuel du propriétaire

Amana NFW5800HW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents