Samsung RL52VEBTS Manuel utilisateur

Catégorie
Congélateurs
Taper
Manuel utilisateur
English
Refrigerator
user manual
imagine the possibilities
Thank you for purchasing a Samsung product.
To receive a more complete service,
please register your product at
www.samsung.com/register
Free Standing Appliance
This manual is made with 100% recycled paper.
02_ safety information
SAFETY INFORMATION
Before operating the
appliance, please read this
manual thoroughly and retain
it at a safe place near the
appliance for your future
reference.
Use this appliance only for
its intended purpose as
described in this instruction
manual.
This appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use
of the appliance by a person
responsible for their safety.
Warnings and Important
Safety Instructions in this
manual do not cover all
possible conditions and
situations that may occur.
It is your responsibility to use
common sense, caution,
and care when installing,
maintaining, and operating
your appliance.
Because these following
operating instructions
cover various models, the
characteristics of your
refrigerator may differ slightly
from those described in this
manual and not all warning
signs may be applicable.
If you have any questions
or concerns, contact your
nearest service center or find
help and information online at
www.samsung.com.
Important safety symbols and
precautions :
WARNING
Hazards or unsafe
practices that may result
in severe personal
injury or death.
CAUTION
Hazards or unsafe
practices that may result
in minor personal
injury or property
damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
safety information
safety information _03
Follow directions
carefully.
Unplug the power plug
from the wall socket.
Make sure the machine
is grounded to prevent
electric shock.
Call the contact center
for help.
Note.
These warning signs are here to
prevent injury to you and others.
Please follow them explicitly.
After reading this section, keep
it in a safe place for future
reference.
SEVERE WARNING
SIGNS FOR
TRANSPORTATION
AND SITE
When transporting and
installing the appliance,
care should be taken to
ensure that no parts of
the refrigerating circuit
are damaged.
- Refrigerant leaking from the
pipe work could ignite or
cause an eye injury.
WARNING
If a leak is detected, avoid
any naked flames or potential
sources of ignition and air the
room in which the appliance is
standing for several minutes.
In order to avoid the creation
of a flammable gas-air mixture
if a leak in the refrigerating
circuit occurs, the size of the
room in which the appliance
may be sited depends on the
amount of refrigerant used.
Never start up an appliance
showing any signs of damage.
If in doubt, consult your dealer.
The room where the
refrigerator will be sited must
be 1m³ in size for every 8g of
R-600a refrigerant inside the
appliance.
The amount of refrigerant in
your particular appliance is
shown on the identification
plate inside the appliance.
04_ safety information
SEVERE WARNING
SIGNS FOR
INSTALLATION
Do not install the
refrigerator in a damp
place or place where it
may come in contact
with water.
- Deteriorated insulation of
electrical parts may cause an
electric shock or fire.
Do not place this refrigerator
in direct sunlight or expose to
the heat from stoves, room
heaters or other appliance.
Do not plug several appliances
into the same multiple power
board.
The refrigerator should always
be plugged into its own
individual electrical which has
a voltage rating that matched
the rating plate.
- This provides the best
performance and also
prevents overloading house
wiring circuits, which could
cause a fire hazard from
overheated wires.
If the wall socket is loose, do
not insert the power plug.
- There is a risk of electric
shock of fire.
Do not use a cord that shows
WARNING
cracks or abrasion damage
along its length or at either
end.
Do not bend the power cord
excessively or place heavy
articles on it.
Do not use aerosols near the
refrigerator.
- Aerosols used near the
refrigerator may cause an
explosion or fire.
This refrigerator must be
properly installed and
located in accordance
with the manual before it
is used.
Connect the power plug in
proper position with the cord
hanging down.
- If you connect the power plug
upside down, wire can get cut
off and cause fire or electric
shock.
Make sure that the power plug
is not squashed or damaged
by the back of the refrigerator.
When moving the refrigerator,
be careful not to roll over or
damage the power cord.
- This constitutes a fire hazard.
The appliance must be
positioned so that the plug is
accessible after installation.
safety information _05
The refrigerator must be
grounded.
- You must ground the
refrigerator to prevent any
power leakages or electric
shocks caused by current
leakage from the refrigerator.
Never use gas pipes,
telephone lines or other
potential lightening rods as
ground.
- Improper use of the ground
plug can result in electric
shock.
If the power cord is
damaged, have it
replaced immediately by
the manufacturer or its
service agent.
The fuse on the refrigerator
must be changed by a
qualified technician or service
company.
- Failing to do so may result
in electric shock or personal
injury.
CAUTION SIGNS FOR
INSTALLATION
• Keep ventilation
opening in the appliance
enclosure or mounting
structure clear of
obstruction.
Allow the appliance to stand
for 2 hours after installation.
SEVERE WARNING
SIGNS FOR USING
Do not insert the power
plug with wet hands.
Do not store articles on the
top of the appliance.
- When you open or close the
door, the articles may fall and
cause personal injury and/or
material damage.
CAUTION
WARNING
06_ safety information
SEVERE WARNING
SIGNS FOR USING
(CONT’D)
Do not put items filled
with water on the
refrigerator.
- If spilled, there is a risk of fire
or electric shock.
Do not let children hang on
the door.
- Failure to do so may cause
serious personal injury.
Do not leave the doors of the
refrigerator open while the
refrigerator is unattended and
do not let children enter inside
of the refrigerator.
- There is a risk of children
entrapment and serious
personal injury because of low
temperature.
Never put fingers or other
objects into the dispenser
hole.
- Failure to do so may cause
personal injury or material
damage.
Do not store volatile or
flammable substances
such as benzene, thinner,
alcohol, ether or LP gas in the
refrigerator.
- The storage of any of
such products may cause
WARNING
explosions.
Do not store low temperature-
sensitive pharmaceuticals
products, scientific materials
or other low temperature-
sensitive products in the
refrigerator.
- Products that require strict
temperature controls must not
be stored in the refrigerator.
Do not place or use electrical
appliance inside the
refrigerator, unless they are of
a type recommended by the
manufacturer.
Do not use a hair dryer to dry
the inside of the refrigerator.
Do not place a lighted candle
in the refrigerator for removing
bad odors.
- This may result in electric
shock or fire.
Do not touch the inside walls
of the freezer or products
stored in the freezer with wet
hands.
- This may cause frostbite.
Do not use mechanical
devices or any other means
to accelerate the defrosting
process, other than those
recommended by the
manufacturer.
Do not damage the refrigerant
safety information _07
circuit.
This product is intended
only for the storage
of food in a domestic
environment.
Bottles should be stored
tightly together so that they do
not fall out.
If a gas leak is detected, avoid
any naked flames or potential
sources of ignition and air the
room in which the appliance is
standing for several minutes.
Use only the LED Lamps
provided by manufacturer or
service agents.
Children should be supervised
to ensure that they do not
play with and/or climb into the
appliance.
Do not disassemble or
repair the refrigerator by
yourself.
- You run risk of causing a fire,
malfunction and/or personal
injury.
In case of malfunction, please
contact your service agents.
If the appliance
generates a strange
noise, a burning or smell
or smoke, unplug the
power plug immediately
and contact your nearest
service center.
- Failing to do so may result in
electric or fire hazards.
Keep ventilation opening in
the appliance enclosure or
mounting structure clear of
obstruction.
If you experience difficulty
when changing the light,
contact service agents.
If the products equipped
with LED Lamp, do not
disassemble Lamp Cover and
LED Lamp by yourself.
- Please contact your service
agents.
If any dust or water is in
refrigerator, pull out power
plug and contact your
Samsung Electronics service
center.
- There is a risk of fire.
08_ safety information
CAUTION SIGNS FOR
USING
To get best performance
of product,
- Do not place foods too closely
in front of the vents at the
rear of the appliance as it can
obstruct free air circulation in
the refrigerator compartment.
- Wrap the food up properly or
place it in airtight containers
before put it into the
refrigerator.
Do not place carbonated
or fizzy drinks in the freezer
compartment.
Do not put bottles or glass
containers in the freezer.
- When the contents freeze, the
glass may break and cause
personal injury and property
damage.
Do not change the
functionality of or modify the
refrigerator.
- Changes or modifications may
result in personal injury and/or
property damage.
Any changes or modifications
performed by a 3rd party on
this completed appliance
is neither covered under
Samsung warranty service,
nor is Samsung responsible
CAUTION
for safety issues and damages
that result from 3rd party
modifications.
Do not block air holes.
- If the air holes are blocked,
especially with a plastic bag,
the refrigerator can be over
cooled.
If this cooling period lasts too
long, the water filter may break
and cause water leakage.
- Do not put any newly
introduced food for freezing
near to already frozen food.
Please observe maximum
storage times and expiry
dates of frozen goods.
Fill water tank, ice tray, water
cubes only with potable water.
Do not apply strong shock
or excessive force onto the
surface of glass.
- Broken glass may result in a
personal injury and/or property
damage.
safety information _09
CAUTION SIGNS
FOR CLEANING AND
MAINTENANCE
Do not directly spray
water inside or outside
the refrigerator.
- There is a risk of fire or electric
shock.
Do not spray inflammable gas
near the refrigerator.
- There is a risk of explosion or
fire.
Do not spray cleaning
products directly on the
display.
- Printed letters on the display
may come off.
Remove any foreign
matter or dust from the
power plug pins.
But do not use a wet
or damp cloth when
cleaning the plug, remove
any foreign material or
dust from the power plug
pins.
- Otherwise there is a risk of fire
or electric shock.
Unplug the refrigerator
before cleaning and
performing maintenance.
CAUTION
SEVERE WARNING
SIGNS FOR DISPOSAL
Ensure that none of the
pipes on the back of the
appliance are damaged
prior to disposal.
R-600a or R-134a is used as
a refrigerant.
Check the compressor label
on the rear of the appliance
or the rating label inside the
refrigerator to see which
refrigerant is used for your
refrigerator.
When this product contains
flammable gas (Refrigerant
R-600a), contact your local
authority in regard to safe
disposal of this product.
Cyclopentane is used as an
insulation blowing gas. The
gases in insulation material
require special disposal
procedure.
Please contact your local
authorities in regard to the
environmentally safe disposal
of this product.Ensure that
none of the pipes on the
back of the appliances are
damaged prior to disposal.
The pipes shall be broke in the
open space.
If the appliance contains iso-
WARNING
10_ safety information
butane refrigerant (R-600a),
a natural gas with high
environmental compatibility
that is, however, also
combustible.
When transporting and
installing the appliance, care
should be taken to ensure that
no parts of the refrigerating
circuit are damaged.
When disposing of this
product or other refrigerators,
remove the door/door seals,
door latch so that small
children or animals cannot
become trapped inside.
Leave the shelves in place so
that children may not easily
climb inside.
Children should be supervised
to ensure that they do not play
with the old appliance.
Please dispose of the
packaging material for this
product in an environmentally
friendly manner.
ADDITIONAL TIPS
FOR PROPER USAGE
In the event of a power failure,
call the local office of your
Electricity Company and ask
how long it is going to last.
- Most power failures that are
corrected within an hour
or two will not affect your
refrigerator temperatures.
However, you should minimize
the number of door openings
while the power is off.
- Should the power failure last
more than 24 hours, remove
all frozen foods.
If keys are provided with the
refrigerator, the keys should
be kept out of the reach of
children and not in vicinity of
the appliance.
The appliance might
not operate consistently
(possibility of temperature
becoming too warm in
refrigerator) when sited for an
extended period of time below
the cold end of the range of
temperature for which the
refrigerating appliance is
designed.
Do not store food which spoils
easily at low temperature,
such as bananas, melons.
safety information _11
Your appliance is frost free,
which means there is no
need to manually defrost
your appliance, as this will be
carried out automatically.
Temperature rising during the
defrost can comply with ISO
requirement.
But if you want to prevent an
undue rise in the temperature
of the frozen food while
defrosting the appliance,
please wrap the frozen food in
several layers of newspaper.
Any increase in temperature of
frozen food during defrosting
can shorten its storage life.
The temperature of two
star section (sections) or
compartment (compartments)
which have two star symbol
(
) is slightly higher than
other freezer compartment
(compartments). The two
star section (sections) or
compartment (compartments)
is (are) based on the
instruction and/or the
condition as delivered.
12_ safety information
contents
SETTING UP YOUR REFRIGERATOR ………………………………………………………………………… 13
OPERATING YOUR REFRIGERATOR ………………………………………………………………………… 19
TROUBLESHOOTING …………………………………………………………………………………………… 25
setting up _13
01 SETTING UP
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on your purchase of this Samsung
Refrigerator.
We hope you enjoy state-of-the-art features and
effi ciencies that this new appliance offers.
This refrigerator must be properly installed and
located in accordance with the manual before it
is used.
Use this appliance only for its intended purpose
as described in this instruction manual.
We strongly recommend that any servicing be
performed by a qualified individual.
Please dispose of the packaging material for this
product in an environmentally friendly manner.
Pull the power plug out of the socket before
changing the interior light of the refrigerator.
- Otherwise, there is a risk of electric shock.
Selecting the best location for the
refrigerator
A location without direct exposure to sunlight.
A location with flat floor surface.
A location with enough space for the refrigerator
door to open easily.
Allow sufficient space to the right, left, back and
top for air circulation.
If the refrigerator does not have enough space,
the internal cooling system may not work
properly.
Please ensure that appliance can be moved freely
in the event of maintenance & service.
Height of the product may be different
depending on the models.
Allow clearance to the right, left, back and top
when installing.
This will help reduce power consumption and
keep your energy bills lower.
Do not install the refrigerator in a place with the
temperature lower than 10°C.
Pull the unit straight out when installing,
servicing or cleaning behind the refrigerator
and push it straight back after work is
complete.
Make sure your fl oor can support fully
loaded refrigerator.
Remove paper on spacer and then attach
two spacers (Gray block) on the back side
of refrigerator for better performance.
Make sure two spacers fi x like below image
when you install the refrigerator.
It is improving the refrigerator performance.
Spacer
Spacer
setting up your refrigerator
CAUTION
or
960mm
50mm
50mm
1,165mm
600mm
560mm
at least
at least
WARNING
14_ setting up
2. Remove the Top cover. Make sure to disconnect
the wire underneath the Top cover.
Be careful not to damage the electrical wires
when removing the Top cover.
3. Disconnect the wire and then remove 3 bolts on
the top of the refrigerator.
Make sure the Fridge door is closed fi rmly.
4. Remove the Fridge door from the Middle hinge
by carefully lifting the door straight up.
Fridge door is heavy, be careful not to injure
yourself when removing the Fridge door.
5. Disassemble the Middle hinge by removing 2
bolts and a screw on the right side.
Remove the Freezer door from the Bottom hinge
by carefully lifting the door straight up.
Freezer door is heavy, be careful not to
injure yourself when removing the Freezer
door.
REVERSING THE
REFRIGERATOR DOOR
Samsung recommends that reversing of
the door opening is only completed by
Samsung approved Service providers. This
will be on a chargeable basis and at the
customers expense.
Any damage caused while attempting to
reverse the door opening is not covered
under the appliance manufactures
warranty. Any repairs requested due to
this circumstance will be completed on a
chargeable basis at the customers expense.
Required Tools
Not provided
Phillips Head
Driver (+)
Flat Head
Driver (-)
10mm Socket
Wrench
(for bolts)
Not provided
Additional part
11mm Wrench
(for hinge
shaft)
3/16” Allen
Wrench
(for middle
hinge)
Top Left
Hinge Cover
(Underneath
the Top Cover)
1. Remove 4 screws on the Top cover of the
refrigerator.
Make sure your refrigerator is unplugged
before handling electrical wires.
Screw
Middle hinge
Middle hinge
Bottom hinge
WARNING
WARNING
CAUTION
CAUTION
CAUTION
CAUTION
setting up _15
01 SETTING UP
10. Switch the side of bottom hinge cap and then
attach the Front leg cover on the bottom of the
refrigerator.
11. Switch the side of the Middle hinge cap,
Screw cap and a Screw from left to the right side.
12. Remove the screw on the bottom right side of
the Freezer door.
Switch the Door stopper and the Hinge grommet
from the right to the left.
13. Switch the Hinge grommet and the Grommet cap on
the top of the Freezer door.
REVERSING THE
REFRIGERATOR DOOR
(CONT’D)
6. Separate the Front leg cover after removing 2
screws.
7. Unscrew 2 bolts tightening the Bottom hinge
and also unscrew a bolt on the left side by the
front leg where removed Bottom hinge will be
attached.
Before removing the Bottom hinge, slightly
turn the front legs clockwise for easier
disassembling and assembling.
8. Switch the position of the Bottom hinge shaft.
Remove the screw on the Auto guide and remove
the Bottom hinge shaft with 11mm wrench.
Attach the Bottom hinge shaft on the left and put
the reversed Auto Guide back.
9. Attach the Bottom hinge on the bottom left side
of the refrigerator where a bolt was previously
removed in step 8.
Screw remaining bolt on the bottom right side of
the refrigerator for the future usage.
Screw
Front leg cover
10mm
10mm
Bottom hinge shaft
Auto guide
Screw
Bottom hinge
cap
Screw cap
Middle hinge cap
Screw
Screw
Hinge grommet
Door stopper
Hinge grommet
Grommet cap
16_ setting up
18. Use 11mm wrench to separate the Top hinge
shaft. Flip the Top hinge and reattach the Top
hinge shaft.
19. Switch the side of the Door cap and the Hinge
grommet on the top of the Fridge door.
20. Reassemble the Top hinge by reversing the step
19. (Make sure to use the Top left hinge cover
which can be found underneath the Top table.)
Put the assembled hinge on the left side of the
fridge door.
Make sure that red tape on the wire is
positioned on the end of the Top left hinge
cover.
REVERSING THE
REFRIGERATOR DOOR
(CONT’D)
14. Carefully put the Freezer door back on.
Assemble the Middle hinge with 2 bolts on the
left side.
A screw will be remained after reversing
freezer door. And it does not affect
performance of the refrigerator.
15. Remove the screw on the bottom right side of
the Fridge door.
Switch the Door stopper and the Hinge grommet
from the right to the left.
16. Remove the Wire cover on the top of the Fridge
door with flat head driver and then take out the
Top hinge and wires from right side of Fridge
door.
17. Detach the Top right hinge cover from the Top
hinge and pull the wires out from the Top right
hinge cover.
Hinge grommet
Door stopper
Door cap
Hinge
grommet
setting up _17
01 SETTING UP
25. Detach the Fridge and
the Freezer door gaskets
and then attach them
after rotating them 180˚.
After reversing the doors, make sure
the Fridge and Freezer door gaskets are
properly arranged. If not, there might
be a noise or dew formed which affects
perfomance of the refrigerator.
REVERSING THE DOOR
HANDLE (TYPE A)
1. Remove 2 screws underneath the Fridge door
and then take off 2 Cap sheets and remove 2
screws on the Freezer door.
2. Slightly push down the Fridge handle and then
remove it by pulling it toward to you.
Slightly push up the Freezer handle and then
remove it by pulling it toward to you.
Disassemble the door handle carefully. Hooks
inside of the door handles can break easily.
REVERSING THE
REFRIGERATOR DOOR
(CONT’D)
21. Carefully put the Fridge door back on.
Then tighten 3 bolts to assemble the Top hinge.
You must reverse the Type B door handle
before putting the Fridge door back.
Please refer to page 18.
For Door handle Type A, make sure to
switch the door handle after reversing the
door.
22. Connect wires and then assemble the Wire cover
on the top of the Fridge door.
23. Change the position of the Top hinge cap.
Connect the wire under the Top cover and put
the Top cover back to its original position.
24. Tighten 4 screws back
to its place.
Top hinge cap
CAUTION
18_ setting up
3. Change the positions of the Handle slider and
spring from the left side to the right side.
Make sure to change position of the Handle slider
cap from the right side to the left side.
4. Assemble the door handle by following step 2
and 1 in reverse order.
This procedure must be done before
‘Reversing the Refrigerator Door’ step 23.
LEVELLING THE
REFRIGERATOR
If the front of the appliance is slightly higher than
the rear, the door can be opened and closed more
easily.
Turn the adjusting legs clockwise to raise and
counter-clockwise to lower the height.
Case 1) The appliance tilts down to the left.
Turn the left adjusting leg in the direction of the
arrow until the appliance is level.
Case 2) The appliance tilts down to the right.
Turn the right adjusting leg in the direction of the
arrow until the appliance is level.
3. Assemble the handles after switching the side of
the Fridge handle and the Freezer handle.
4. Tighten 2 screws underneath the Fridge door and
then assemble 2 screws and 2 Cap sheets on
the Freezer door.
REVERSING THE DOOR
HANDLE (TYPE B)
1. Remove 2 screws underneath the Fridge door
and then pull the Handle cover.
Disassemble the Handle cover carefully.
Hooks inside of the Handle cover can break
easily.
2. Remove 2 screws on the Handle grommets.
Remove the Handle grommets and disassemble
the Easy handle.
Screw
Cover handle
Screw
handleGrommet
Spring
Slider
Screw
WARNING
operating _19
02 OPERATING
CHECKING THE CONTROL
PANEL
Each time you press the button, a short
beep will sound.
USING THE CONTROL PANEL
(TYPE A)
1
Fridge
Touch the Fridge button to set the
fridge to desired temperature from
the range between 1°C and 7°C.
Default set temperature is set on 3°C
and each time you press the Fridge
button, temperature will change in following order
and temperature indicator will display the desired
temperature.
When the temperature setting is done, the set
temperature is displayed initially for 5 seconds and
then indicator will display the actual temperature of
the fridge.
2
Freezer
Touch the Freezer button to set
the freezer to desired temperature
from the range between -14°C and
-25°C. Default set temperature is
set on -20°C and each time you touch the Freezer
button, temperature will change in following order
and temperature indicator will display the desired
temperature.
When the temperature setting is done, the set
temperature is displayed initially for 5 seconds and
then indicator will display the actual temperature of
the freezer.
Fridge or Freezer temp indicator will blink
when temperature in the fridge or freezer
compartment goes up dramatically by
storing warm food or frequent door opening.
(Fridge or Freezer temperature indicator will
stop blinking when temperature in the fridge
or freezer is become normal.
If temperature indicator does not stop
blinking after several hours, please contact
your service center.
3
Lighting (Hold 3sec for Alarm)
Touch the Lighting button to activate
the Lighting Function and the light
underneath fridge door will be on.
The light keeps on while Lighting
function is activated.
If you want to adjust the brightness of the light,
touch the Lighting button again.
(Adjusting brightness may not be available
depending on the models.)
To deactivate the Lighting function, touch the
Lighting button again until the light is off.
Touch the Lighting button for longer than 3 seconds
to activate the Alarm function.
Alarm indicator will light up and the refrigerator will
alert you with alarm sound if the refrigerator door is
kept open for longer than 2 minutes.
To deactivate the Alarm function, touch the Lighting
button for longer than 3 seconds.
Lighting activated : Light stay on.
Lighting deactivated : If you open the
freezer door with the fridge door closed
the Light will be turned on.
operating your refrigerator
Ehi hb h
(TYPE A)
4
5
1
2
3
(TYPE B)
2 1
Light off
Light off
Light on
Light on
(Bright)
(Bright)
Light on
Light on
(Medium)
(Medium)
Light on
Light on
(Dark)
(Dark)
20_ operating
USING THE CONTROL PANEL
(TYPE B)
1
Coldest
Press the Coldest button one or
more times to lower the temperature
of the refrigerator.
Temperature indicator will change
from cold to coldest.
Default set temperature is the Mid-
point temperature.
When all lights are on, the temperature is at its
coldest.
2
Cold
Press the Cold button one or more
times to raise the temperature of the
refrigerator.
Temperature indicator will change
from coldest to cold.
Default set temperature is the Mid-
point temperature.
When one light is on, the temperature is at its cold.
There are five temperature settings,
represented by five indicator lights.
The freezer temperature will be adjusted
automatically according to the refrigerator
temperature (as stated in below).
If you need to freeze large amount of food stuff,
set the temperature of refrigerator as the coldest
temperature at least 24 hours before.
Temp indicator will blink when temperature
in the fridge or freezer compartment goes up
dramatically by storing warm food or frequent
door opening.
Temperature indicator will stop blinking when
temperature in the fridge or freezer becomes
normal.
If temperature indicator does not stop blinking
after several hours, please contact your service
center.
4
Vacation
Touch the Vacation button to activate
the Vacation function.
Vacation indicator will light up and the
refrigerator will set the temperature to
15°C to minimize the power consumption when you
are going on a long vacation or business trip or you
do not need to use the refrigerator.
While Vacation function is activated, freezer
compartment remains on.
Vacation function will be automatically
deactivated if you adjust fridge temperature
while Vacation function is on.
Make sure to remove foods in the fridge
compartment before using Vacation
function.
5
Power Freeze
Touch the Power Freeze button to
activate the Power Freeze function.
Power Freeze indicator will light up and
the refrigerator will speed up the time
to needed to freeze products in the freezer.
Power freeze function will be activated for 72 hours
and freezer indicator will display -25°C.
The Power Freeze function switches off
automatically.
When the Power Freeze process is completed, the
Power freeze indicator switches off and the freezer
switches back to the previous temperature setting.
When you use this function, the energy consumption
will increase.
To deactivate the Power Freeze function, touch the
Power Freeze button again.
If you need to freeze large amount of food
stuff, activate Power Freeze function at least
24 hours before.
Cold Coldest
Temperature of Freezer(Fridge)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Samsung RL52VEBTS Manuel utilisateur

Catégorie
Congélateurs
Taper
Manuel utilisateur

dans d''autres langues