Whirlpool WRF560SEHW Mode d'emploi

Marque: Whirlpool

Modèle: WRF560SEHW

Catégorie: Frigos

Taper: Mode d'emploi

THANK YOU for purchasing this high-quality product. Register your new refrigerator at www.whirlpool.com. In Canada, register

your refrigerator at www.whirlpool.ca.

For future reference, please make a note of your product model and serial numbers. These can be located on the inside wall

of the refrigerator compartment.

Model Number__________________________________________________ Serial Number __________________________________________________

Para obtener acceso a “Instrucciones para el usuario del refrigerador” en español, o para obtener información adicional acerca

de su producto, visite: www.whirlpool.com.

Necesitará su número de modelo y de serie, ubicado en el interior del compartimiento del refrigerador.

REFRIGERATOR

USER INSTRUCTIONS

Table of Contents / Table des matières

REFRIGERATOR SAFETY .....................................................................2

INSTALLATION INSTRUCTIONS ..........................................................3

Unpack the Refrigerator ......................................................................3

Location Requirements........................................................................3

Remove and Replace Refrigerator Doors and Drawer Front..............4

Electrical Requirements.......................................................................8

Water Supply Requirements................................................................8

Connect the Water Supply ..................................................................8

Handle Installation and Removal...................................................... 10

Door Closing and Door Alignment.................................................... 11

FILTERS AND ACCESSORIES ........................................................... 11

Water Filtration System .................................................................... 11

Install Air Filter................................................................................... 12

Install Produce Preserver.................................................................. 12

Accessories....................................................................................... 13

REFRIGERATOR USE ......................................................................... 13

Opening and Closing Doors ............................................................. 13

Using the Controls............................................................................ 14

Water Dispenser ............................................................................... 15

Ice Maker .......................................................................................... 16

REFRIGERATOR FEATURES ............................................................. 16

Refrigerator Shelves ......................................................................... 17

Pantry Drawer ................................................................................... 17

Crisper............................................................................................... 17

DOOR FEATURES ............................................................................... 18

Condiment Bins ................................................................................ 18

Fresh Bin........................................................................................... 18

Half-Height Bin.................................................................................. 18

REFRIGERATOR CARE ...................................................................... 19

Cleaning ............................................................................................ 19

Changing the Light Bulbs................................................................. 19

TROUBLESHOOTING ......................................................................... 20

Operation .......................................................................................... 20

Noise ................................................................................................. 21

Temperature and Moisture............................................................... 22

Ice and Water.................................................................................... 23

Doors................................................................................................. 25

PERFORMANCE DATA SHEET.......................................................... 26

WARRANTY ......................................................................................... 27

SÉCURITÉ DU RÉFRIGÉRATEUR ......................................................28

INSTRUCTIONS D’INSTALLATION ....................................................29

Déballage du réfrigérateur.................................................................29

Exigences d’emplacement................................................................30

Retrait et réinstallation des portes du réfrigérateur et de l'avant du

tiroir....................................................................................................30

Spécifications électriques .................................................................35

Spécifications de l’alimentation en eau.............................................35

Raccordement à l’alimentation en eau..............................................35

Installation et démontage des poignées...........................................37

Fermeture et alignement de la porte.................................................38

FILTRES ET ACCESSOIRES ...............................................................39

Système de filtration de l'eau............................................................39

Installation du filtre à air.....................................................................39

Installation du conservateur pour produits frais ...............................40

Accessoires .......................................................................................41

UTILISATION DU RÉFRIGÉRATEUR..................................................41

Ouverture et fermeture des portes....................................................41

Utilisation des commandes...............................................................41

Distributeur d’eau ..............................................................................43

Machine à glaçons.............................................................................44

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...................................44

Tablettes du réfrigérateur ..................................................................44

Garde-manger ...................................................................................45

Bac à légumes...................................................................................45

CARACTÉRISTIQUES DE LA PORTE.................................................46

Balconnets à condiments..................................................................46

Balconnet fraîcheur............................................................................46

Balconnet mi-hauteur........................................................................46

ENTRETIEN DU RÉFRIGÉRATEUR....................................................47

Nettoyage ..........................................................................................47

Remplacement des ampoules d’éclairage........................................47

DÉPANNAGE ........................................................................................48

Fonctionnement.................................................................................48

Bruit....................................................................................................49

Température et humidité ...................................................................50

Glaçons et eau...................................................................................51

Portes.................................................................................................53

FEUILLE DE DONNÉES SUR LA PERFORMANCE...........................54

GARANTIE............................................................................................ 55

W10360467C

REFRIGERATOR SAFETY

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous –

even if they will sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

■ Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

Remove the Packaging

■ Remove tape and glue residue from surfaces before turning on

the refrigerator. Rub a small amount of liquid dish soap over the

adhesive with your fingers. Wipe with warm water and dry.

■ Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see “Refrigerator Safety.”

■ Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in “Refrigerator Care.”

Location Requirements

To ensure proper ventilation for your refrigerator, allow for a

¹⁄₂" (1.25 cm) of space on each side and at the top. Allow for

a 1" (2.54 cm) space behind the refrigerator. If your refrigerator

has an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space between the refrigerator and

wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where

the temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F (32°C).

It is recommended that you do not install the refrigerator near

a heat source, such as an oven or radiator.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as floor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

2" (5.08 cm)

¹⁄₂

" (1.25 cm)

Remove and Replace Refrigerator

Doors and Drawer Front

Depending on the width of your door opening, it may be

necessary to remove the refrigerator doors to move the

refrigerator into your home.

Remove Doors and Hinges

IMPORTANT:

■ If the refrigerator was previously installed and you are moving it

out of the home, before you begin, turn the refrigerator control

OFF, and unplug the refrigerator or disconnect power. Remove

food and any adjustable door or utility bins from doors.

■ Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. Provide additional support for the

refrigerator door while the hinges are being removed. Do not

depend on the door gasket magnets to hold the door in place

while you are working.

■ All graphics referenced in the following instructions

are included later in this section after “Final Steps.”

TOOLS NEEDED: ⁵⁄₁₆", ³⁄₈", and ¹⁄₄" hex head socket

wrenches, Torx

®†

T25 screwdriver, #2 Phillips screwdriver,

and a flat-blade screwdriver.

Remove Doors and Hinges

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull

it toward you.

3. Starting with the right-hand side door, remove the parts

for the top hinge as shown in Top Hinge graphic. Lift

the refrigerator door from the bottom hinge pin.

4. Remove the hinge pin cover from the bottom hinge pin

and keep it for later use. See Bottom Hinge graphic.

5. Remove top hinge cover from the left-hand side refrigerator

door. Remove the parts for the top hinge as shown in Top

Hinge graphic.

External Dispenser Models Only:

■ Disconnect the wiring plug, located under the top left-hand

side door hinge, by wedging a flat-blade screwdriver

or your fingernail between the two sections. See Wiring

Plug graphic.

■ Disconnect the water line, located under the top left-hand

side door hinge, by pulling back on the locking collar

while pulling the water line out of the water line connector.

See Water Dispenser Tubing Connection graphic.

6. Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the hinge pin cover from

the bottom hinge pin and keep it for later use. See Bottom

Hinge graphic.

Replace Doors and Hinges

1. Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door while

the hinges are being moved. Do not depend on the door gasket

magnets to hold the door in place while you are working.

2. Assemble the parts for the top hinges as shown in Top

Hinge graphic. Do not tighten the screws completely.

External Dispenser Models Only:

■ Reconnect the wiring plug on top of the left-hand

side refrigerator door.

■ Reconnect the water line by pulling back the locking collar

ring while firmly pushing the water line into the connector.

Check for leaks.

3. Align the door so that the bottom of the refrigerator door aligns

evenly with the top of the freezer drawer. Tighten all screws.

4. Replace the top hinge covers.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

†®TORX is a registered trademark of Acument Intellectual Properties, LLC.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and replace

the freezer drawer. Graphics are included later in this section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to

the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws

in the drawer front.

3. Lift drawer front upward and off the screws. See Drawer

Front Removal graphic.

4. The refrigerator leveling/roller assembly protrudes from each

side of the cabinet base. Remove the three screws attaching

each assembly, and remove the assemblies. See Refrigerator

Leveling/Roller Assembly graphic.

Replace Drawer Front

1. Align the leveling/roller assembly with the holes on each side of

the refrigerator cabinet. Using the screws removed, reinstall the

assemblies to the cabinet base. Tighten the screws completely.

2. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

3. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets.

Completely tighten the four screws. See Drawer Front

Replacement graphic.

4. Replace the base grille.

■ Pull open the freezer drawer.

■ Align the three clips on the back of the base grille

with the three tabs at the base of the refrigerator.

■ Push the base grille in toward the refrigerator until

it is firmly in place.

Final Steps

1. Plug into a grounded 3 prong outlet.

2. Return all removable parts to doors and drawer and

food to refrigerator and freezer.

A. Tab

B. Clip

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Style 1 - Non-Dispenser Models

Drawer Front Removal

A. Loosen 4 Door Bracket Screws

Drawer Front Replacement

Door Removal and Replacement

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

" Hex-Head Hinge Screws

D. Top Hinge

A. Hinge Pin Cover

C. Hinge Screws

B. Bottom Hinge

Bottom Hinges

Leveling/Roller Assembly

Assembly Screws

Style 2 - External Water Dispenser Models

Door Removal and Replacement

Wiring Plug

Water Dispenser

Tubing Connection

A. Blue Outer Ring

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

C. ⁵⁄₁₆" Hex-Head Hinge Screws

D. Top Hinge

A. Hinge Pin Cover

C. Hinge Screws

B. Bottom Hinge

Bottom Hinges

Leveling/Roller Assembly

Assembly Screws

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator and approved accessories

be provided. Use an outlet that cannot be turned off by a switch.

Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn off Cooling, and then disconnect

the refrigerator from the electrical source. When you have finished,

reconnect the refrigerator to the electrical source and turn on

Cooling. See “Using the Control(s).”

Water Supply Requirements

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call

a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system going to the water inlet valve

of the refrigerator needs to be between 30 and 120 psi

(207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage. The tank capacity could be too low to keep

up with the requirements of the refrigerator.

■ If your refrigerator has a water filter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See “Water

Filtration System.”

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ Use copper tubing or Whirlpool supply line, Part

Number 8212547RP, and check for leaks.

■ Install copper tubing only in areas where the temperatures

will remain above freezing.

TOOLS NEEDED:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or ³⁄₁₆"

(4.76 mm) saddle valve which reduces water flow and clogs

more easily.

Connect to Water Line

Style 1

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long enough

to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold

water pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning.

Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing.

Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe

you have selected.

6. Fasten the shut-off valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten or you may crush the copper tubing.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

■ Flat-blade screwdriver

■ ⁷⁄₁₆" and ¹⁄₂" Open-end or 2

adjustable wrenches

■ ¹⁄₄" Nut driver

■ ¹⁄₄" Drill bit

■ Cordless drill

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shut-off valve

G. Packing nut

DEF

7. Slip the compression sleeve and compression nut onto the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn on the main water supply. Flush the tubing until water

is clear. Turn off the shut-off valve on the water pipe. Coil

the copper tubing.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray

water tube on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown.

NOTE: Tighten the nut by hand. Then tighten it with

a wrench two more turns. Do not overtighten.

4. Turn shut-off valve on.

5. Check for leaks. Tighten any nuts or connections

(including connections at the valve) that leak.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut.

Do not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shut-off valve on.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

6. On models with ice makers, the ice maker is equipped with

a built-in water strainer. If your water conditions require a

second water strainer, install it in the ¹⁄₄" (6.35 mm) water line

at either tube connection. Obtain a water strainer from your

nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray

water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not

long enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is

needed in order to connect the water tubing to an existing

household water line. Thread the provided nut onto the

coupling on the end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with

a wrench two more turns. Do not overtighten.

4. Turn shut-off valve on.

5. Check for leaks. Tighten any nuts or connections

(including connections at the valve) that leak.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

NOTES:

■ Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill ice container.

■ For models with a water dispenser, flush the water system.

See “Water Dispenser.”

A. Bulb

B. Nut (provided)

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (provided)

E. Ferrule (purchased)

F. Nut (purchased)

G.Household water line

A B C D E F G

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Handle Installation and Removal

Parts Included: Refrigerator door handles (2),

Freezer drawer handle (1)

Tools Needed: ¹⁄₈" Hex key wrench

Install Door Handles

NOTE: Handle mounting setscrews are preinstalled inside

the handle.

1. Remove the handles from the packaging inside the refrigerator.

2. Open a refrigerator door. On the opposite door, place

the handle on the shoulder screws with the setscrews

facing the adjacent door.

3. Firmly push the handle toward the door until the handle

base is flush against the door.

4. While holding the handle, insert the short end of the hex

key into the upper hole and slightly rotate the hex key until

it is engaged in the setscrew.

5. Using a clockwise motion tighten the setscrew just until it

begins to contact the shoulder screw. Do not fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

7. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

8. Repeat steps 2 through 6 to install the other handle onto

the adjacent refrigerator door.

Install Drawer Handle

1. With the freezer drawer closed, place the handle on

the shoulder screws with the setscrews facing down

toward the floor.

2. Firmly push the handle toward the drawer until the handle

base is flush against the drawer.

3. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until it is engaged in the setscrew.

4. Using a left-to-right motion tighten the setscrew a quarter-turn

at a time. Repeat until the screw feels tight.

5. Repeat steps 3 and 4 to fasten the right-hand setscrew

to the shoulder screw.

6. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

7. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into a setscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a right-to-left motion loosen the setscrew a quarter-turn

at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the

handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

A. Shoulder screws

B. Setscrews inside the handle

A. Shoulder screw

B. Setscrews inside the handle

Door Closing and Door Alignment

IMPORTANT: To comply with American Disabilities Act

(ADA) guidelines, fully retract the rollers into the cabinet

to lower the refrigerator.

Door Closing

The base grille covers the leveling screws and roller assemblies

located at the bottom of the refrigerator cabinet below the freezer

drawer. Before making adjustments, remove the base grille and

move the refrigerator to its final location.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2. Move the refrigerator to its final location.

NOTE: To allow the refrigerator to roll easier, raise the

leveling legs off the floor by turning the leveling screws

counterclockwise. The front rollers will be touching the floor.

3. So the doors will close easier, use a ¹⁄₄" hex driver to turn

both leveling screws clockwise. This will raise the front of

the refrigerator tilting it slightly downward to the rear. Turn

both leveling screws the same amount.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling screws. This makes it easier

to turn the screws.

4. Open both doors again to make sure they close as easily as

you like and that they stay closed. If not, tilt the refrigerator

slightly more to the rear by turning both leveling screws to

the right. It may take several more turns.

NOTE: To keep the refrigerator level, you should turn

both leveling screws the same amount.

5. Replace the base grille.

■ Pull open the freezer drawer.

■ Align the 3 clips on the back of the base grille with the

3 tabs at the base of the refrigerator.

■ Push the base grille in toward the refrigerator until

it is firmly in place.

Door Alignment

If the space between the refrigerator doors and freezer drawer

looks uneven, you can adjust it using the following instructions:

1. Remove the top hinge cover.

2. Loosen the top hinge screws using a ⁵⁄₁₆" socket or wrench.

3. Have someone hold the door in place or put a spacer

between the doors and drawer.

4. Tighten the top hinge screws once the door is in the

desired location.

5. Replace the top hinge cover.

FILTERS AND

ACCESSORIES

Water Filtration System

Water Filter Status Light

The water filter status light on the control panel will help

you know when to order and replace the water filter.

■ GOOD - The water filter icon on the control lights up in BLUE.

■ ORDER a replacement filter - The water filter icon on

the control lights up in YELLOW.

■ REPLACE the water filter - The water filter icon on the control

lights up in RED and “Replace Filter” will appear on the display.

■ EXPIRED - The water filter icon lights up in RED and “Replace

Filter” flashes on the display.

NOTE: If water flow to your water dispenser or ice maker

decreases noticeably, change the filter sooner. The

disposable water filter should be replaced at least every

6 months, depending on your water quality and usage.

■ After changing the water filter, reset the status. Press and hold

the Water Filter button for 3 seconds. When the system is reset,

the water filter icon will return to BLUE and the words “Replace

Filter” will disappear from the display.

A. Leveling screw

B. Front roller

¹⁄₄"

A. Tab

B. Clip

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Changing the Water Filter

1. Locate the water filter in the top-right corner of the

refrigerator compartment.

2. Lift open the filter cover door. The filter will be released

and then eject as the door is opened.

3. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some

spilling may occur. Use a towel to wipe up any spills.

4. Take the new filter out of its packaging and remove the

covers from the O-rings. Be sure the O-rings are still in

place after the covers are removed.

5. With the arrow pointing up, align the new filter with the filter

housing and slide it into place. The filter cover door will

automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap

the filter into place. You may need to press hard.

7. Flush the water system. See “Water Dispenser”

or “Water and Ice Dispensers.”

Install Air Filter

(on some models)

The air filter reduces the buildup of odors. This helps to maintain

a cleaner environment inside the refrigerator.

On some models, your refrigerator's accessory packet includes

an air filter, which must be installed prior to use. On some models,

the air filter is already installed at the factory.

Installing the Air Filter

Install the air filter behind the vented door, located along

the rear interior wall of the refrigerator compartment.

1. Remove the air filter from its packaging.

NOTE: An air filter status indicator is included with the air

filter. The indicator is not needed for models that display

the air filter status on the control panel.

2. Lift open the vented door.

3. Snap the filter into place.

Air Filter Status Indicator

The control panel displays the Air Filter status.

■ GOOD - The air filter icon on the control panel lights up

in BLUE.

■ ORDER a replacement - The air filter icon on the control

panel lights up in YELLOW.

■ REPLACE air filter - The air filter icon on the control panel

lights up in RED and “Replace Filter” will appear.

■ EXPIRED - The air filter icon lights up in RED and “Replace

Filter” flashes on the control panel.

After replacing the air filter, press and hold the Air Filter button for

3 seconds. The filter icons will turn off. See “Using the Control(s).”

When the system is reset, the air filter icon will return to BLUE and

the words “Replace Filter” will disappear from the control panel.

NOTE: At any filter status, pressing and holding the Air Filter button

for 3 seconds will reset the air filter status to Good and the air filter

icon will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months

or when the status indicator air filter icon turns on and starts

flashing when the refrigerator door is opened.

To order a replacement air filter, contact us. See “Accessories.”

1. Remove the used air filter by squeezing in on the side tabs.

2. Install the new air filter and reset the status indicator using

the instructions in the previous section.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene, to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Sensitivity to

Ethylene

Production

Apples High Very High

Asparagus Med. Very Low

Berries Low Low

Broccoli High Very Low

Cantaloupe Med. High

Carrots Low Very Low

Citrus Fruit Med. Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

Installing the Produce Preserver

1. Find the Produce Preserver housing inside the refrigerator.

2. Open the housing by pulling up and out on the back.

3. Remove the Produce Preserver pouches from the

packaging and place them into the housing.

NOTE: For best performance, always use 2 pouches.

4. Adhere the Produce Preserver housing to the back wall

of the crisper drawer according to the instructions included

in the package.

Installing the Status Indicator

The produce preserver comes with a status indicator, which

should be activated and installed at the same time the pouches

are installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator

until the bubble pops to activate the indicator.

3. Slide open the cap on the top of the produce

preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is

visible through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator’s bubble

has not been popped.

Replacing the Produce Preserver

The disposable pouches should be replaced every 6 months or

when the status indicator changes completely from white to red.

To order replacements, contact us. See “Accessories”

for information on ordering.

1. Remove the used pouches from the produce

preserver housing.

2. Remove the used status indicator.

3. Install the replacement pouches and status indicator using

the instructions in the previous sections.

Accessories

The following accessories are available for your refrigerator.

To order, contact us and ask for the part numbers.

In the U.S.A., visit our web page www.whirlpool.com/

accessories or call 1-800-901-2042.

In Canada, visit our web page www.whirlpool.ca

or call 1-800-807-6777.

affresh

Stainless Steel Cleaner:

Order Part #W10355016

affresh

Stainless Steel Wipes:

Order Part #W10355049

affresh

Kitchen & Appliance Cleaner:

Order Part #W10355010

Water Filter:

Order Part #W10295370A or FILTER1

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver:

Order Part #W10346771A or FRESH1

Water Filter, Air Filter and Ethylene Filter Bundle Pack:

Order Part #W103655758BL

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors

can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

■ When the left-hand refrigerator door is opened, the hinged

seal automatically folds inward so that it is out of the way.

■ When both doors are closed, the hinged seal automatically

forms a seal between the 2 doors.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

CAUTION

ITA

Read cautions on back.

ATTENTION

ITA

Lisez des prudences sur le revers.

A. Hinged seal

Using the Controls

IMPORTANT:

■ Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature

controls to a colder than recommended setting will not cool

the compartments any faster.

■ The recommended setting should be correct for normal

household refrigerator use. The controls are set correctly when

milk or juice is as cold as you like and when ice cream is firm.

■ If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not blocked

before adjusting the controls.

Control Panel

Depending on your model, your refrigerator has either an internal

control panel, located at the top of the refrigerator compartment,

or an external control panel, located above the external water

dispenser. Follow the instructions specific to your model.

Internal Control Panel

External Control Panel

IMPORTANT (External Control only): The display screen on the

dispenser control panel will turn off automatically and enter “sleep”

mode when the control buttons and dispenser paddles have not

been used for 2 minutes or more. While in “sleep” mode, the first

press of a control button will only reactivate the display screen,

without changing any settings. After reactivation, changes to any

settings can then be made. If no changes are made within

2 minutes, the display will re-enter “sleep” mode.

■ Touch any control button on the dispenser panel to activate

the display screen.

Temperature Control

For your convenience, the temperature control is preset at the

factory. When you first install your refrigerator, make sure the

control is still set to the recommended setting as shown.

Recommended Setting “3 Snowflakes”

Adjusting the Controls

If you need to adjust the temperature in either the refrigerator

or freezer compartment, use the settings listed in the following

chart as a guide.

■ Press the Temp button to display the desired number

of snowflakes from 1 snowflake (least cold) to all

5 snowflakes (coldest).

NOTE: Except when starting the refrigerator, do not adjust the

control more than one setting at a time. Wait 24 hours between

adjustments for the temperature to stabilize.

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is

turned off. Follow the directions specific to your model.

Internal Control Panel

■ To turn cooling off, press and hold both the Fast Cool

and Moisture Control buttons at the same time for 3 seconds.

When cooling is OFF, “Cooling Off” will appear on the display

screen.

■ To turn cooling back on, press and hold both the Fast Cool

and Moisture Control buttons at the same time for 3 seconds.

When cooling is ON, “Cooling Off” will disappear and the

previously selected settings will appear on the display screen.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm FRIDGE TEMP

one more snowflake

FREEZER too warm/too little ice FREEZER TEMP

one more snowflake

REFRIGERATOR too cold FRIDGE TEMP

one less snowflake

FREEZER too cold FREEZER TEMP

one less snowflake

External Control Panel

■ To turn cooling off, press and hold both the Freezer Temp and

Fridge Temp buttons at the same time for 3 seconds. When

cooling is off, “Cooling Off” will appear on the display screen.

■ To turn cooling back on. Press and hold both the Freezer

Temp and Fridge Temp buttons at the same time for 3 seconds.

When cooling is on, “Cooling Off” will disappear and the

previously selected settings will appear on the display screen.

Additional Features

Door Open Alarm

■ The Door Open icon lights up whenever either door is opened.

■ When either door is open for 5 minutes and cooling is on, an

alert tone will sound three times, and the Door Open icon will

flash seven times. This pattern will repeat every 2 minutes until

all the doors are closed properly. The feature then resets and

will reactivate when either door is left open again for 5 minutes.

NOTES:

■ To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press

any button on the control panel. The alarm sound will be

temporarily turned off, but the Door Open icon will still be

displayed on the dispenser control panel.

■ Both doors must be fully closed to turn off the Door

Open icon.

Fast Cool

The Fast Cool feature assists during times of high refrigerator use,

full grocery loads or temporarily warm room temperatures.

■ Press FAST COOL to set the freezer and refrigerator to

the coldest temperature settings. Press FAST COOL again

to return to the selected temperature set point.

NOTES:

■ The Fast Cool icon will be illuminated while the

refrigerator is in Fast Cool mode.

■ The Fast Cool feature will turn off automatically

after 24 hours.

Moisture Control

The moisture control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Moisture Control is ON.

NOTE: The moisture control icon will light up to indicate the

feature is ON.

To turn on/off the moisture control feature:

■ Internal Control Panel - Press and hold MOISTURE

CONTROL for 3 seconds.

■ External Control Panel - Press and hold LIGHT for 3 seconds.

Water Filter Status Light and Reset

The filter reset control allows you to restart the water filter

status tracking feature each time you replace the water filter.

See “Water Filtration System.”

■ Press and hold WATER FILTER for 3 seconds, to reset the

water filter status to Good. The water filter icon will turn blue.

Air Filter Status Light and Reset

The filter reset control allows you to restart the air filter status

tracking feature each time you replace the air filter. See “Install

Air Filter.”

■ Press and hold AIR FILTER for 3 seconds, to reset the air filter

status to Good. The air filter icon will turn blue.

Water Dispenser

(on some models)

IMPORTANT:

■ Allow 3 hours for the refrigerator to cool down and chill water.

■ Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced.

■ The dispensing system will not operate when the

refrigerator door is open.

Flush the Water System

Air in the water dispensing system can cause the water dispenser

to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water

line and filter and prepares the water filter for use. Additional

flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

1. Using a sturdy container, depress and hold the water dispenser

paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds.

3. Repeat steps 1 and 2 until water begins to flow.

4. Once water begins to flow, continue depressing and releasing

the dispenser paddle (5 seconds on, 5 seconds off) until a

total of 4 gal. (15 L) has been dispensed.

Dispense Water

IMPORTANT:

■ The dispensing system will not operate when the

refrigerator door is open.

■ The display screen on the dispenser control panel will turn off

automatically and enter “sleep” mode when the control buttons

and dispenser paddles have not been used for 2 minutes or

more. While in “sleep” mode, the first press of a control button

will only reactivate the display screen, without changing any

settings. After reactivation, changes to any settings can then be

made. If no changes are made within 2 minutes, the display will

re-enter “sleep” mode.

To dispense water:

1. Press a sturdy glass against the water dispenser paddle.

2. Remove the glass to stop dispensing.

Dispenser Light

When you use the dispenser, the light will automatically turn on.

If you want the light to be on continuously, you may turn on the

light. The light icon will illuminate when the light is ON.

ON: Press LIGHT quickly to turn on the dispenser light.

OFF: Press LIGHT quickly to turn off the dispenser light.

NOTES:

■ If you unintentionally press and hold the Light button for

3 seconds or longer, you will turn on the Moisture Control

feature. If this happens, press and hold LIGHT for 3 seconds

again to turn off the Moisture Control feature.

■ The dispenser lights are LEDs that cannot be changed.

If it appears that your dispenser lights are not working,

see “Troubleshooting” for more information.

Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the refrigerator,

to the ice maker, or to the dispenser light. It simply deactivates the

controls and dispenser paddles. To turn off the ice maker, see “Ice

Maker and Storage Bin.”

■ Press and hold FAST COOL for 3 seconds to lock

the dispenser.

■ Press and hold FAST COOL for 3 seconds again to

unlock the dispenser.

The lock icon will illuminate when the dispenser is locked.

Ice Maker

IMPORTANT: For models with a water filter, after connecting the

refrigerator to a water source or replacing the water filter, fill and

discard 3 full containers of ice to prepare the water filter for use.

Turning the Ice Maker On/Off

To turn on the ice maker, simply lower the wire shut-off arm.

To manually turn off the ice maker, lift the wire shut-off arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will raise

the wire shut-off arm to the OFF (arm up) position. Do not force the

wire shut-off arm up or down.

Ice Storage Bin

1. Wash the ice storage bin with mild soap and warm water.

2. Slide the ice storage bin under the ice maker and push

it toward the back as far as it will go.

3. Lower the arm on the ice maker to the ON position.

NOTE: It usually takes approximately 24 hours for the

ice maker to begin producing ice. You may notice the ice

has an “off-taste.” If so, discard the first 3 batches of

ice produced. After that the “off-taste” should be gone.

Ice Production Rate

■ The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period. Allow 3 days to completely fill the

ice container.

■ To increase ice production, lower the freezer and refrigerator

temperature. See “Using the Control(s).” Wait 24 hours

between adjustments.

Remember

■ The quality of your ice will be only as good as the quality

of the water supplied to your ice maker. Avoid connecting

the ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply

cannot be avoided, make sure the water softener is

operating properly and is well maintained.

■ Do not use anything sharp to break up the ice in the bin.

This can cause damage to the ice storage bin and the

dispenser mechanism.

■ Do not store anything on top of or in the ice maker or

ice storage bin.

REFRIGERATOR

FEATURES

NOTE: Your model may have some or all of these features.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Refrigerator Shelves

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Glass Shelves

To remove a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift the back or front of the shelf

past the stop. Pull the shelf out the rest of the way.

To replace a shelf:

1. Slide the back of the shelf into the track in the wall

of the cabinet.

2. Guide the front of the shelf into the shelf track. Be sure

to slide the shelf in all the way.

Foldaway Shelf (on some models)

To retract the foldaway shelf:

■ Retract the foldaway section of the shelf by holding the front

of the shelf with one hand and lifting up on the center front

of the shelf. Then push back and down on the shelf until it

slides beneath the back section of the shelf.

To replace the foldaway shelf:

■ Replace the foldaway section of the shelf by holding the front

of the shelf with one hand and pulling the center of the shelf

until the foldaway section is returned to its full shelf position.

Pantry Drawer

To remove and replace the pantry drawer:

1. Slide pantry drawer out to the stop.

2. Lift front of pantry drawer with one hand while supporting

bottom of drawer with other hand. Slide drawer out the rest

of the way.

3. Replace the drawer by sliding it back in fully past

the drawer stop.

Pantry Drawer Cover

To remove and replace the pantry drawer cover:

1. Remove the pantry drawer.

2. From underneath, push up on the glass cover and pull it out.

3. Replace the pantry drawer cover by lowering it into place.

4. Replace the pantry drawer.

Pantry Drawer Control

The amount of air flowing through the pantry drawer affects

the temperature inside the drawer.

The airflow control is located on the left side of the pantry drawer.

To adjust the airflow:

■ Colder - Slide the control forward, toward the front

of the pantry drawer. The airflow is open.

■ Cold - Slide the control all the way toward the rear of

the pantry drawer. The airflow is closed, as shown.

Crisper

Crisper Drawers

To remove and replace the crisper drawer:

1. Slide the crisper drawer straight out to the stop. Lift

the front and slide the drawer out the rest of the way.

2. Replace the drawer by sliding the drawer in fully past the stop.

Crisper Cover

To remove and replace the glass crisper cover:

1. Pull the glass straight out.

2. Replace the glass by pushing it straight in.

Crisper Humidity Control (on some models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and HIGH.

LOW (open) lets moist air out of the crisper for best storage

of fruits and vegetables with skins.

■ Fruit: Wash, let dry and store in refrigerator in plastic bag

or crisper. Do not wash or hull berries until they are ready

to use. Sort and keep berries in original container in crisper,

or store in a loosely closed paper bag on a refrigerator shelf.

■ Vegetables with skins: Place in plastic bag or plastic container

and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage

of fresh, leafy vegetables.

■ Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

DOOR FEATURES

NOTE: Your model may have some or all of these features.

Condiment Bins

To remove and replace the condiment bins:

1. Tilt the bin by pulling it outward.

2. Remove the bin by lifting it upward off the glides.

3. Replace the bin by sliding it back onto the glides

and then push it closed.

Fresh Bin

(on some models)

To remove and replace the fresh bin:

1. Open the bin by grasping the top center lip of the bin

and tilting the bin outward.

2. Remove the bin by grasping both sides of the bin and

lifting the bin upward off the glides.

3. Replace the bin by sliding it back into its tilted position

on the glides and then push it closed.

Half-Height Bin

(on some models)

To remove and replace the half-height bin:

1. Tilt the bin by pulling it outward.

2. Remove the bin by lifting it upward off the glides.

3. Replace the bin by sliding it back onto the glides

and then push it closed.

REFRIGERATOR CARE

Cleaning

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT:

■ Because air circulates between both sections, any odors

formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To

avoid odor transfer and drying out of food, wrap or cover

foods tightly.

■ For stainless steel models, stainless steel is corrosion-resistant

and not corrosion-proof. To help avoid corrosion of your

stainless steel, keep your surfaces clean by using the

following cleaning instructions.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, muriatic acid,

cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on exterior surfaces (doors and

cabinet), plastic parts, interior and door liners or gaskets. Do not

use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth

and a mild detergent in warm water.

3. Clean the exterior surfaces.

Painted metal: Wash painted metal exteriors with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

Stainless steel: Wash stainless steel surfaces with a clean,

soft cloth or sponge and a mild detergent in warm water.

Rinse surfaces with clean, warm water and dry immediately

to avoid water spots.

NOTE: When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is particularly

greasy or dusty, or there is significant pet traffic in the home,

the condenser should be cleaned every 2 to 3 months to

ensure maximum efficiency.

If you need to clean the condenser:

■ Remove the base grille.

■ Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

■ Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

Changing the Light Bulbs

IMPORTANT:

■ Not all appliance bulbs will fit your refrigerator. Be sure

to replace the bulb with an appliance bulb of the same

size, shape and wattage.

■ To ensure optimum refrigerator performance, replace

light bulbs as soon as they burn out.

Refrigerator Compartment Light

The lighting located at the top of the refrigerator compartment

never needs to be replaced. If the lights do not illuminate when

the door is opened, call for assistance or service. In the U.S.A.,

call 1-800-253-1301. In Canada, call 1-800-807-6777.

Freezer Compartment Light (on some models)

1. Unplug the refrigerator or disconnect power.

2. Remove the light shield (on some models).

■ Top of the freezer compartment - Slide the light shield

toward the back of the compartment to release it from

the light assembly.

3. Replace the burned-out bulb with an appliance bulb(s)

no greater than 25 watts.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

WARNING

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and scan the code with your mobile device, or visit www.whirlpool.com/product_help.

In Canada, visit www.whirlpool.ca.

In the U.S.A.:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

In Canada:

Whirlpool Brand Home Appliances

Customer eXperience Centre

200 – 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Operation

PROBLEM POSSIBLE CAUSES SOLUTIONS

The refrigerator

will not operate

Check electrical supply Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Make sure there is power to the outlet. Plug in a lamp

to see if the outlet is working.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Check controls Make sure the controls are turned on. See “Using the Controls.”

New installation Allow 24 hours following installation for the refrigerator

to cool completely.

NOTE: Adjusting the temperature controls to the coldest setting

will not cool either compartment quicker.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

La page charge ...

Whirlpool WRF560SEHW Mode d'emploi

Marque: Whirlpool

Modèle: WRF560SEHW

Catégorie: Frigos

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WRF560SEHW User guide

Whirlpool WRF560SEHW Mode d'emploi

Whirlpool WRF560SEHW Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents