Simplicity 01656 Manuel utilisateur

Marque: Simplicity

Modèle: 01656

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Owner’s Manual / Manuel de l'Utilisateur

Questions? Help is just a moment away!

Vous avez des questions? Vous n'avez pas besoin d'aller loin pour trouver de l'aide!

Call: Generac Generator Helpline / Appelez la ligne d'assistance de Generac Motor - 1-800-270-1408 M-F 8-5 CT

Model No. 1656-1 (4,000 Watt AC Generator) Manual No. 191519GS Revision 7 (02/22/2005)

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WISCONSIN, U.S.A.

Generac Portable Products is a licensed trademark of Briggs & Stratton Power Products.

Generac Portable Products est une marque déposéee autorisée de Briggs & Stratton Power Products.

Before using this product, read this manual and follow all

Safety Rules and Operating Instructions.

CAUTION

Avant d’utiliser ce produit, veuillez lire le manuel et suivre

toutes les directives relatives à la sécurité et à l’utilisation.

ATTENTION

4000EXL Extended Life Generator

TABLE OF CONTENTS

Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14

Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-16

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

EQUIPMENT

DESCRIPTION

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

This generator is an engine–driven, revolving field,

alternating current (AC) generator. It was designed to

supply electrical power for operating compatible electrical

lighting, appliances, tools and motor loads.The generator’s

revolving field is driven at about 3,600 rpm by a single-

cylinder engine.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload

Generator”.

Every effort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter or otherwise improve the product

and this document at any time without prior notice.

The Emission Control System for this generator is

warranted for standards set by the Environmental

Protection Agency. For warranty information refer to the

engine owner’s manual.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION,WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER indicates

a hazard which, if not avoided, will result in death or

serious injury. WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might

result in minor or moderate injury. CAUTION, when used

without the alert symbol, indicates a situation that could

result in equipment damage. Follow safety messages to

avoid or reduce the risk of injury or death.

Hazard Symbols and Meanings

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Fire

Explosion

Toxic Fumes

Kickback

Electrical Shock

Electrocution

Electrical Shock

Explosive Pressure

Chemical Burn

Hot Surface

may be reproduced or transmitted in any form by any

means without the express written permission of Briggs &

Stratton Power Products Group, LLC.

4000EXL Extended Life Generator

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in bodily injury and/or property

damage.

WARNING

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays near battery for a long time

after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

WARNING

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting engine.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING

EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

4000EXL Générateur Qui Dure Longtemps

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of injury

and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or call

1-800-270-1408.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect

them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The generator must be at least 5 feet from structures having

combustible walls and/or other combustible materials.

• Keep at least 3 feet of clearance on all sides of generator for

adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code). Other

states may have similar laws. Federal laws apply on federal

lands. If you equip the muffler with a spark arrester, it must be

maintained in effective working order.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass, brush,

ect. can catch fire.

WARNING

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than

you can let go.

Broken bones, fractures, bruises or sprains could

result.

WARNING

4000EXL Générateur Qui Dure Longtemps

KNOW YOUR GENERATOR

Read this owner’s manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

120 Volt AC, 20 Amp

Duplex Receptacle

Fuel Tank

Idle Control Switch

Choke Lever

Recoil Starter

12 Volt DC, 10 Amp

Receptacle

Run/Stop Switch

120 Volt AC, 30 Amp

Receptacle

Double Pole Circuit

Breaker (AC)

120/240 Volt AC,

20 Amp Receptacle

Spark Arrester Muffler

Air Cleaner

Grounding Fastener

Start Button

12 Volt DC,10 Amp Receptacle — Recharge a discharged

12 Volt automotive type battery through this receptacle.

120 Volt AC, 20 Amp Duplex Receptacle — May be used to

supply electrical power for the operation of 120 Volt AC, 20 Amp,

single phase, 60 Hz electrical lighting, appliance, tool and motor

loads.

120 Volt AC, 30 Amp Receptacle — May be used to supply

electrical power for the operation of 120 Volt AC, 30 Amp, single

phase, 60 Hz electrical lighting, appliance, tool and motor loads.

120/240 Volt AC, 20 Amp Receptacle — May be used to

supply electrical power for the operation of 120 and/or 240 Volt

AC, 20 Amp, single phase, 60 Hz electrical lighting, appliance, tool

and motor loads.

Air Cleaner — Protects engine by filtering dust and debris out

of intake air.

Choke Lever — Used when starting a cold engine.

Circuit Breaker (AC) — The 120 Volt AC, 30 Amp receptacle is

provided with a "push to reset" circuit breaker to protect the

generator against electrical overload.

Double Pole Circuit Breaker (AC) — A double pole circuit

breaker is provided to protect all the receptacles and generator

against electrical overload.

Fuel Tank — Capacity of 4.5 U.S. gallons.

Grounding Fastener — Used for proper grounding of unit.

Idle Control Switch — With this switch set to ON, printed

circuit board in control panel automatically reduces engine speed

when no load is connected and increases engine to proper speed

when load is applied. However, be sure switch is OFF when

starting engine.

Oil Fill Cap — Add oil to engine here.

Recoil starter — Used to start the engine manually.

Run/Stop Switch — Set this switch to "Run" before using

recoil starter. Set switch to "Stop" to switch OFF engine.

Spark Arrester Muffler — Exhaust muffler lowers engine noise

and is equipped with a spark arrester screen.

Start Button — When pressed, cranks engine to start.

Oil Fill Cap

Circuit Breaker (AC)

4000EXL Extended Life Generator

ASSEMBLY

IMPORTANT: Read entire owner’s manual before you

attempt to assemble or operate your new generator.

Carton Contents

Parts included:

• Generator

• Wheel kit

• Battery

• Battery charge cables

• Battery float charger

• Locking 20 Amp plug

• Locking 30 Amp plug

• Engine oil

• Two packets of fuel stabilizer

• Owner's manual

• Engine manual

If any of the above parts are missing or damaged, call the

generator helpline at 1–800–270–1408.

Attach Negative Battery Wire

The sealed battery on the generator is fully charged and

pre–installed except for the negative (black) battery cable.

To install:

1. Cut off tie wrap securing loose end of negative (black)

cable.

2. Connect negative (black) battery cable to negative (–)

terminal on battery (Figure 1).

3. Verify that connections to battery and generator are

correct and secure.

Install Handle

To install the handle you need the following tools:

• 2 - 13 mm (1/2”) box, open end, or socket wrenches

Install handle as follows:

1. Remove hardware from bracket on handle.

2. Place lifting handle on alternator end of cradle so that

handle falls between the two twistlock receptacles as

shown in Figure 2.Attach handle with provided cap

screws and hex nuts.Tighten with 13mm wrenches.

Figure 1 — Negative Battery Connection

Positive

battery cable

Negative

battery cable

Figure 2 — Install Handle

Capscrew

Handle

Hex

Nut

4000EXL Extended Life Generator

BEFORE STARTING THE

ENGINE

Add Engine Oil

• Place generator on a level surface.

• Refer to engine owner’s manual and follow oil

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer to

engine owner’s manual for recommendations.

NOTE: The generator assembly rotates on a prelubricated

and sealed ball bearing that requires no additional

lubrication for the life of the bearing.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine

Modifications).

1. Use clean, fresh, regular UNLEADED fuel with a

minimum of 85 octane with equipment. DO NOT use

fuel which contains Methanol. DO NOT mix oil with

fuel.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add regular unleaded fuel to fuel tank. Be careful

not to fill above the baffle.This allows adequate space

for fuel expansion (Figure 3).

4. Install fuel cap and wipe up any spilled fuel.

CAUTION

• Refer to engine manual for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will result

in equipment failure.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank.Allow space for fuel expansion.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WARNING

FUEL

TANK

Figure 3 — Typical Fuel Expansion Space

Baffle

4000EXL Extended Life Generator

USING THE GENERATOR

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on

the AC output receptacles.The system ground is connected

to the AC neutral wire (the neutral is bonded to the

generator frame).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction.

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there may

be additional regulations which must be observed.

Connecting to a Building’s Electrical

System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician.The

connection must isolate the generator power from utility

power, and must comply with all applicable laws and

electrical codes.

Generator Location

Generator Clearance

The generator must be at least 5 ft. (152 cm) from

structures having combustible walls and/or other

combustible materials. Leave at least 3 ft. (92 cm) all around

generator including overhead, for adequate cooling,

maintenance and servicing.

Place generator in a well ventilated area, which will allow

for removal of deadly exhaust gas. DO NOT place

generator where exhaust gas could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes or other openings that can allow

exhaust gas to collect in a confined area (Figure 4).

Prevailing winds and air currents should be taken into

consideration when positioning generator.

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

WARNING

Figure 4 — Generator Clearance

Exhaust Port

Typical Generator Shown

4000EXL Extended Life Generator

OPERATING THE

GENERATOR

IMPORTANT: Always unplug the battery float charger

before starting the generator.

Starting the Engine

Disconnect all electrical loads from the generator. Follow

these start instruction steps in numerical order:

1. Turn fuel valve to “On” position (Figure 5).

2. Make sure Idle Control switch is in “Off” position

(Figure 6).

3. Start engine according to instructions given in engine

owner’s manual.

NOTE: If engine still fails to start after 3 pulls, check for

proper oil level in crankcase.This unit is equipped with a

Low Oil Shutdown System. See engine manual.

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hz electrical loads.

• DO NOT connect 240 Volt loads to the 120 Volt

receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

“Don’t Overload Generator”.

Figure 5 — Fuel Shut-off Valve

Figure 6 — Idle Control Switch

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity can

damage generator and/or electrical devices connected

to it.

CAUTION

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The generator must be at least 5 feet from structures having

combustible walls and/or other combustible materials.

• Keep at least 3 feet of clearance on all sides of generator for

adequate cooling, maintenance and servicing.

• In the State of California a spark arrester is required by law

(Section 4442 of the California Public Resources Code). Other

states may have similar laws. Federal laws apply on federal

lands. If you equip the muffler with a spark arrester, it must be

maintained in effective working order.

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass, brush,

ect. can catch fire.

WARNING

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

Rapid retraction of starter cord (kickback) will

pull hand and arm toward engine faster than

you can let go.

Broken bones, fractures, bruises or sprains could

result.

WARNING

4000EXL Extended Life Generator

Stopping the Engine

1. Turn OFF and unplug ALL electrical loads from

generator panel receptacles. NEVER start or stop engine

with electrical devices plugged in and turned ON.

2. Move idle control switch to “Off” position.

3. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and generator.

4. Turn engine off according to instructions given in the

engine owner’s manual.

5. Move fuel valve to “Off” position.

Operating Automatic Idle Control

This switch is designed to greatly improve fuel economy.

When this switch is turned ON, the engine will only

run at its normal high governed engine speed when

electrical loads are connected.When an electrical load is

removed, the engine will run at a reduced speed.

With the switch off, the engine will run at the normal

high engine speed. Always have the switch off when

starting and stopping the engine.

Charging a Battery

Your generator has the capability of recharging a

discharged 12 Volt automotive or utility style storage

battery. DO NOT use the unit to charge any 6 Volt

batteries. DO NOT use the unit to crank an engine having

a discharged battery.

To recharge 12 Volt batteries, proceed as follows:

1. Check fluid level in all battery cells. If necessary, add

ONLY distilled water to cover separators in battery

cells. DO NOT use tap water.

2. If battery is equipped with vent caps, make sure they

are installed and are tight.

3. If necessary, clean battery terminals.

4. Connect battery charge cable connector plug to panel

receptacle identified by the words “12-VOLTS D.C.”.

5. Connect battery charge cable clamp with red handle

to the positive (+) battery terminal (Figure 7).

6. Connect battery charge cable clamp with black handle

to the negative (–) battery terminal (Figure 7).

7. Start engine. Let engine run while battery recharges.

8. When battery has charged, shut down engine.

NOTE: Use an automotive hydrometer to test battery state

of charge and condition. Follow the hydrometer

manufacturer’s instructions carefully. Generally, a battery is

considered to be at 100% state of charge when specific gravity

of its fluid (as measured by hydrometer) is 1.260 or higher.

COLD WEATHER

OPERATION

Under certain weather conditions (temperatures below

40°F [4°C] combined with high humidity), your generator

may experience icing of the carburetor and/or the

crankcase breather system.To reduce this problem, you

need to perform the following:

1. Make sure generator has clean, fresh fuel.

2. Open fuel valve (turn valve to open position).

3. Use SAE 5W-30 oil (synthetic preferred, see engine

manual).

4. Check oil level daily or after every eight (8) hours of

operation.

Figure 7 — Battery Connections

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

Storage batteries give off explosive hydrogen gas

during recharging.

Hydrogen gas stays near battery for a long time

after battery has been charged.

Slightest spark will ignite hydrogen and cause

explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery fluid will cause severe

chemical burns.

DANGER

4000EXL Extended Life Generator

5. Maintain generator following “Maintenance Schedule”

in engine manual.

6. Shelter unit from elements.

In an emergency, use the original shipping carton as a

temporary shelter:

7. Cut off all carton flaps.

8. Cut out one long side of carton to expose muffler side

of unit as shown in Figure 8.

IMPORTANT: The generator must be at least 5 ft.

(152 cm) from structures having combustible walls and/or

other combustible materials. Leave at least 3 ft. (92 cm) all

around generator including overhead, for adequate cooling,

maintenance and servicing.

9. Cut appropriate slots to access receptacles of unit.

10. Start unit, then place carton over it.

IMPORTANT: Remove shelter when temperatures are

above 40°F [4°C].

For a more permanent shelter, build a structure that will

enclose three sides and the top of the generator.

7. Make sure entire muffler-side of generator is exposed,

as shown in Figure 8.

IMPORTANT: The generator must be at least 5 ft.

(152 cm) from structures having combustible walls and/or

other combustible materials. Leave at least 3 ft. (92 cm) all

around generator including overhead, for adequate cooling,

maintenance and servicing.

8. Face exposed end away from wind and elements.

9. Structure should hold enough heat created by the

generator to prevent icing problem.

10. Start and run engine outdoors.

11. Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes or other

openings.

12. DO NOT enclose generator any more than shown in

Figure 8.

13. Remove shelter when temperatures are above 40°F

[4°C].

14. Turn engine OFF and let cool two (2) minutes before

refueling.

Figure 8 — Permanent Cold Weather Shelter

Wind

• DO NOT touch hot surfaces.

• Allow equipment to cool before touching.

• The generator must be at least 5 feet from structures having

combustible walls and/or other combustible materials.

• Keep at least 3 feet of clearance on all sides of generator for

adequate cooling, maintenance and servicing.

• Remove shelter when temperatures are above 40°F [4°C].

Running engines produce heat.Temperature of

muffler and nearby areas can reach or exceed

150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass, brush,

ect. can catch fire.

WARNING

• Operate generator ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or enclosure,

including the generator compartment of a recreational vehicle

(RV).

Running generator gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide will cause nausea,

fainting or death.

WARNING

4000EXL Extended Life Generator

HOW TO USE THE

BATTERY CHARGER

Use battery float charger jack to keep the starting battery

charged and ready for use. Battery charging should be done

in a dry location, such as inside a garage.

1. Plug charger into unit’s “Battery Float Charger” jack,

which is located on the starter switch (Figure 9). Plug

battery charger into a 120 Volt AC wall receptacle.

2. Unplug charger from unit and wall outlet when

generator is being started and while in operation.

3. Keep charger plugged in when generator is not in use

to prolong battery life.The charger has a built in float

equalizer and will not overcharge battery, even when

plugged in for an extended period of time.

IMPORTANT: See “Battery Maintenance” on page 16 for

additional information.

RECEPTACLES

120/240 Volt AC, 20 Amp Locking

Receptacle

Use a NEMA L14-20 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volts at 20 Amps (or greater)

(Figure 10).You can use the same 4-wire cord if you plan to

run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single

phase loads requiring up to 2,000 watts of power at

16.6 Amps for 120 Volts; 4,000 watts of power (4.0 kW) at

16.6 Amps for 240 Volts.The outlet is protected by a

double pole circuit breaker.

Figure 9 — Battery Charger Jack

• NEVER attempt to power a device requiring more amperage

than generator or receptacle can supply.

• DO NOT overload the generator. See “Don’t Overload

Generator”.

Receptacles may be marked with rating value greater

than generator output capacity.

CAUTION

Figure 10 — 120/240 Volt AC, 20 Amp Receptacle

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-20

Ground (Green)

4000EXL Extended Life Generator

120 Volt AC, 30 Amp Locking

Receptacle

Use a NEMA L5-30 plug with this receptacle. Connect a

3-wire cord set rated for 125 Volts AC at 30 Amps to the

plug (Figure 11).

Use this receptacle to operate 120 Volt AC, 60 Hz, single

phase loads requiring up to 3,600 watts (3.6 kW) of power

at 30 Amps.The outlet is protected by a double pole circuit

breaker and a 30 Amp push-to-reset circuit breaker.

120 Volt AC, 15 Amp Duplex

Receptacle

Each of these outlets is protected against overload by a

double pole circuit breaker (Figure 12).

Use each outlet to operate 120 Volt, 60 Hz, single phase

loads requiring 1,800 (1.8 kW) watts at 15 Amps of current.

12 Volt DC, 10 Amp Receptacle

This receptacle allows you to recharge a 12 Volt

automotive or utility style storage battery with the battery

charge cables provided (Figure 13).

This receptacle can not recharge 6 Volt batteries and can

not be used to crank an engine having a discharged battery.

See the section “Charging a Battery” (page 10) before

attempting to recharge a battery.

Figure 11 — 120 Volt AC, 30 Amp, Locking Receptacle

3-Wire Cord Set

Neutral

120V

Hot

Ground (Green)

NEMA L5-30

Figure 13 — 12 Volt DC, 10 Amp Receptacle

Figure 12 — 120 Volt AC, 15 Amp Duplex Receptacle

4000EXL Extended Life Generator

DON'T OVERLOAD

GENERATOR

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.This is

the amount of power your generator must produce to

keep your items running. See Figure 14.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to the

total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices,

it is important to take care when adding electrical loads to

your generator.There should be nothing connected to the

generator outlets before starting it's engine.The correct

and safe way to manage generator power is to sequentially

add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly.

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.Take

special care to consider surge loads in generator capacity,

as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 -

Light (75 Watts) 75 -

3075 Total

Running Watts

1800 Highest

Surge Watts

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt 75 -

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 Cu. Ft. 800 1600

Water Well Pump - 1/3 HP 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 HP 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 -

Coffee Maker 1500 -

Electric Stove - Single Element 1500 -

Hot Plate 2500 -

Family Room

DVD/CD Player 100 -

VCR 100 -

Stereo Receiver 450 -

Color Television - 27” 500 -

Personal Computer w/17” monitor 800 -

Other

Security System 180 -

AM/FM Clock Radio 300 -

Garage Door Opener - 1/2 HP 480 520

Electric Water Heater - 40 Gallon 4000 -

DIY/Job Site

Quartz Halogen Work Light 1000 -

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 HP 1000 1000

Circular Saw - 7 1/4” 1500 1500

Miter Saw - 10” 1800 1800

Planer/Jointer - 6” 1800 1800

Table Saw/Radial Arm Saw - 10” 2000 2000

Air Compressor - 1-1/2 HP 2500 2500

Figure 14 - Wattage Reference Chart

4000EXL Extended Life Generator

SPECIFICATIONS

Maximum Surge Watts . . . . . . . . . . . . . . . . . . 6,600 Watts

Continuous Wattage Capacity . . . . . . . . . . . . 4,000 Watts

Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0

Rated Maximum Continuous Load Current

At 120 Volts . . . . . . . . . . . . . . . . . . . . . . . . . 33.3 Amps

At 240 Volts . . . . . . . . . . . . . . . . . . . . . . . . . 16.6 Amps

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-phase

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hertz

Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . 4.5 U.S. gallons

Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 lbs.

GENERAL MAINTENANCE

RECOMMENDATIONS

The Owner/Operator is responsible for making sure that

all periodic maintenance tasks are completed on a timely

basis; that all discrepancies are corrected; and that the unit

is kept clean and properly stored. NEVER operate a

damaged or defective generator.

NOTE: If equipped with inflatable tires, make sure tires

are inflated to the value marked on the tire or within

15 and 40 psi.

NOTE: Should you have questions about replacing

components on your Generac Portable Products generator,

please call 1-800-270-1408 for assistance.

Engine Maintenance

See engine owner’s manual for instructions.

KEEP OUT OF REACH OF CHILDREN. DON'T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture or any corrosive vapors. Cooling air

slots in the generator must not become clogged with

snow, leaves or any other foreign material.

NOTE: DO NOT use a garden hose to clean generator.

Water can enter engine fuel system and cause problems. In

addition, if water enters generator through cooling air slots,

some of the water will be retained in voids and cracks of

the rotor and stator winding insulation.Water and dirt

buildup on the generator internal windings will eventually

decrease the insulation resistance of these windings.

Fuel Valve Maintenance

The fuel valve is equipped with a fuel sediment cup, screen,

retaining ring and o-ring that need to be cleaned every

6 months or 100 hours (whichever occurs first).

1. Move fuel valve to “Off” position.

2. Remove sediment cup from fuel valve. Remove o-ring,

retaining ring and screen from fuel valve (Figure 15).

Figure 15 — Fuel Valve Maintenance

Sediment Cup

O-ring

Retaining Ring

Screen

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

4000EXL Extended Life Generator

3. Wash sediment cup, o-ring, retaining ring, and screen in

a nonflammable solvent. Dry them thoroughly.

4. Place screen, retaining ring, and o-ring into fuel valve.

Install sediment cup and tighten securely.

5. Move fuel valve to “On” position, and check for leaks.

Replace o-ring if there is any leakage.

Battery Maintenance

Other than float charging, described elsewhere, no

maintenance is required for the battery. Keep the battery

and terminals clean and dry.

IMPORTANT: Battery charging should be performed in a

dry location, such as inside a garage.

Generator Cleaning

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and debris.

• Use low pressure air (not to exceed 25 psi) to blow

away dirt. Inspect cooling air slots and opening on

generator.These openings must be kept clean and

unobstructed.

STORAGE

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot

be done and you must store the unit for more than

30 days, use the following guidelines to prepare it for

storage.

Generator Storage

• Clean the generator as outlined in “Generator Cleaning”.

• Check that cooling air slots and openings on generator

are open and unobstructed.

Engine Storage

See engine owner’s manual for instructions.

Other Storage Tips

• To prevent gum from forming in fuel system or on

essential carburetor parts, empty all two supplied fuel

stabilizer containers into fuel tank and fill with fresh

gasoline. Run the unit for several minutes to circulate the

additive through the carburetor.The unit and fuel can

then be stored for up to 24 months.Additional fuel

stabilizer can be purchased locally.

• DO NOT store gasoline from one season to another

unless it has been treated as described above.

• Replace fuel container if it starts to rust. Rust and/or dirt

in fuel can cause problems if it's used with this unit.

• Store in clean and dry area.

• DO NOT expose generator to excessive moisture, dust, dirt,

or corrosive vapors.

• DO NOT insert any objects through cooling slots.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the

cover on the equipment.

Storage covers can be flammable.

WARNING

4000EXL Extended Life Generator

TROUBLESHOOTING

Problem Cause Correction

No AC output is available, but

generator is running.

1. One of the circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord

set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact Authorized service facility.

3. Check and repair.

4. Connect another device that is in

good condition.

Generator runs good at no-load

but "bogs" down" when loads are

connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See "Don't Overload Generator".

3. Contact Authorized service facility.

Generator will not start; or starts

and runs rough.

1. Failed battery.

2. Low oil level.

1. Replace battery.

2. Fill crankcase to proper level or

place generator on level surface.

Generator shuts down during

operation.

1. Out of gasoline.

2. Low oil level.

1. Fill fuel tank.

2. Fill crankcase to proper level or

place generator on level surface.

Generator lacks power. Load is too high. See "Don't Overload Generator".

4000EXL Extended Life Generator

NOTES

GENERAC PORTABLE PRODUCTS OWNER EQUIPMENT WARRANTY POLICY

Effective November 1, 2004

WARRANTY PERIOD*

* The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the

period of time stated in the table above. "Consumer use" means personal residential household use by a retail consumer.

"Commercial use" means all other uses, including use for commercial, income producing or rental purposes. Once equipment has

been used commercially, it shall thereafter be considered to be in commercial use for purposes of this warranty.

** The engine and starting batteries are warranted solely by the manufacturers of those products.

WARRANTY REGISTRATION IS NOT NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON POWER

PRODUCTS EQUIPMENT.SAVE YOUR PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE

INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED,THE MANUFACTURING DATE OF THE

EQUIPMENT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

About your equipment warranty:

We welcome warranty repair and apologize to you for being inconvenienced.Any Authorized service dealer may perform warranty

repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For

example, warranty service would not apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping,

handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the

equipment has been removed or the equipment has been altered or modified. During the warranty period, the Authorized service

dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal use and service.This

warranty will not cover following repairs and equipment:

• Normal Wear: Outdoor power equipment, like all mechanical devices, needs periodic parts, service and replacement to perform

well.This warranty does not cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or

unauthorized installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper

maintenance, repair or storage so as, in our judgment, to adversely affect its performance and reliability.This warranty also does not

cover normal maintenance such as adjustments, fuel system cleaning and obstruction (due to chemical, dirt, carbon or lime, etc.).

• Other Exclusions: Also excluded from this warranty are wear items such as quick couplers, oil gauges, belts, o-rings, filters,

pump packing, etc., pumps which have been run without water supplied or damage or malfunctions resulting from accidents,

abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration.Accessory parts such as guns,

hoses, wands and nozzles are excluded from the product warranty.This warranty excludes failures due to acts of God and other

force majeure events beyond the manufacturers control.Also excluded is used, reconditioned, and demonstration equipment;

equipment used for prime power in place of utility power and equipment used in life support applications.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON,WISCONSIN, U.S.A.

LIMITED WARRANTY

"Generac Portable Products is a licensed trademark of Briggs & Stratton Power Products. Briggs & Stratton Power Products will

repair or replace, free of charge, any part, or parts of the equipment** that are defective in material or workmanship or both.

Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser.This

warranty is effective for the time periods and subject to the conditions provided for in this policy. For warranty service, find your

nearest Authorized service dealer by calling 1-800-270-1408.Warranty service may only be performed by a Briggs & Stratton

Power Products Authorized service dealer.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE TIME PERIOD SPECIFIED, OR TO THE EXTENT PERMITTED

BY LAW.ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER

ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some countries or

states do not allow limitations on how long an implied warranty lasts, and some countries or states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.This warranty gives

you specific legal rights and you may also have other rights that vary from country to country or state to state.”

PRODUCTS** CONSUMER USE COMMERCIAL USE

Pressure Washer 1 year 90 days

Portable Generator 2 years (2nd year parts only) 1 year

4000EXL Extended Life Generator

TABLE DES MATIÈRES

Règles de Sécurité. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-22

Connaissez Votre Générateur . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25

Opération . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-32

Caractéristiques du Produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34

Rangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

DESCRIPTION DE L ÉQUIPEMENT

Lisez avec soin ce manuel et familiarisez-vous avec

votre générateur. Connaissez ses applications, ses

limitations et les dangers qu'il implique.

Ce générateur est un générateur entraîné par un moteur à champ

magnétique rotatif produisant du courant alternatif (c.a.). Il a été

conçu pour fournir du courant électrique pour faire marcher des

charges compatibles d'éclairage, d'appareils ménagers, d'outil et de

moteur. Le champ tournant du générateur est entraîné à

3,600 T/M par un moteur seul cylindrique.

ATTENTION! NE PAS dépasser la capacité en watts ou en

Ampères du générateur.Voir "Ne Pas Surcharger Générateur"

pour l'information spécifique.

Tout a été mis en oeuvre pour que les informations contenues

dans ce manuel soient exactes et à jour. Cependant, nous se

réserve le droit de changer, d'altérer ou d'améliorer le produit à

n'importe quel moment sans avis préalable.

Le Système de contrôle de l'émission du générateur est garanti

pour des normes établies par L'Agence de protection de

l'environnement. Pour des informations sur la garantie, se reporter

au manuel du moteur.

RÈGLES DE SÉCURITÉ

Ceci est la sûreté le symbole vif. Il est utilisé pour

vous alerter aux dangers de blessure personnels

potentiels. Obéir tous messages de sûreté qui suivent

ce symbole éviter la blessure ou la mort possibles.

Le symbole indiquant un message de sécurité est accompagné d'un

mot indicateur (DANGER,ATTENTION,AVERTISSEMENT), d'un

message illustré et/ou d'un message de sécurité visant à vous

avertir des dangers. DANGER indique un danger qui, s'il n'est pas

évité, provoquera des blessures graves, voire fatales.

AVERTISSEMENT indique un danger qui, s'il n'est pas évité, peut

provoquer des blessures graves, voire fatales. ATTENTION

indique un danger qui, s'il n'est pas évité, peut provoquer des

blessures mineures ou légères. Le mot ATTENTION, lorsqu'il est

utilisé sans le symbole d'alerte, indique une situation pouvant

endommager l'équipement. Suivez les messages de sécurité pour

éviter ou réduire les risques de blessures ou de mort.

Symboles de Danger et Moyens

L’échappement du moteur de ce produit contient des produits

chimiques que l’État de Californie considère comme causant le

cancer, des déformations à la naissance ou d’autres dangers

concernant la reproduction.

AVERTISSEMENT

Feu

Explosion

Emanations Toxiques

Surface Chaude

Choc Électrique

Électrocution

Choc Électrique

Pression Explosive

Brûlures Chimiques

Recul

La page charge ...

Simplicity 01656 Manuel utilisateur

Marque: Simplicity

Modèle: 01656

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 01656 User manual

Simplicity 01656 Manuel utilisateur

Simplicity 01656 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents