LG 40445 Le manuel du propriétaire

Front-Loading Automatic Washer

Use & Care Guide

Lavadora automática de carga frontal

Manual de uso y cuidado

Laveuse automatique à chargement frontal

Guide d’utilisation et d’entretien

Models/Modelos/Modèles 796.4044#

# = color number, número de color, numéro de couleur

MFL62526816

Sears Brands Management Corporation, Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

www.sears.com

www.sears.ca

Designed to use only HE

High Efficiency detergent

Diseñado para utilizar solamente

detergente de alta eficacia

Conçu pour l'utilisation d'un détergent

haute efficacité seulement

Protocol P172

Sanitization Performance of Residential

and Commercial, Family Sized Clothes

Washers

Protocolo P172

Ejecucion de Saneamiento en la zona

residencial y comercial, lavodoras del uso

del hogar

Protocole P172

Performance en matière de désinfection

des laveuses résidentielles et

commerciales de grande taille

FRANÇAIS

ESPAÑOL

ENGLISH

2

TABLE OF CONTENTS

PRODUCT RECORD

PROTECTION AGREEMENTS

SAFETY MESSAGES ...........................................................................3

IMPORTANT SAFETY INSTRUCTIONS ...........................................3-5

GROUNDING REQUIREMENTS...........................................................5

FEATURES AND BENEFITS

Key Parts and Components................................................................6

Included Accessories..........................................................................6

Optional Accessories ..........................................................................6

INSTALLATION REQUIREMENTS

Key Dimensions and Specifications....................................................7

Choose the Proper Location ...............................................................7

Flooring...............................................................................................7

Clearances..........................................................................................7

INSTALLATION INSTRUCTIONS

Unpacking and Removing Shipping Bolts...........................................8

Connecting the Water Lines................................................................9

Connecting the Drain Hose...............................................................10

Connect to the Power Supply ...........................................................10

Leveling the Washer .........................................................................11

Installation of non-skid pads (optional) .............................................11

HOW TO USE

Control Panel Features.....................................................................12

Operating the Washer.......................................................................13

Cycle Guide ......................................................................................14

Sorting Wash Loads..........................................................................15

About the Dispenser .........................................................................16

Detergent and Dispenser Use...........................................................17

Time and Status Display...................................................................18

Cycle Modifier Buttons......................................................................19

Steam Cycles and Options ...............................................................20

ADD STEAM Option ......................................................................20

Using the STEAM REFRESH Cycle ..............................................20

Cycle Option Buttons ........................................................................21

DELAY START ..............................................................................21

2

nd

RINSE.......................................................................................21

STAIN TREAT................................................................................21

Special Functions..............................................................................21

CONTROL LOCK...........................................................................21

CLEAN WASHER ..........................................................................21

CARE AND CLEANING

Regular Cleaning.........................................................................22-23

Cleaning the Exterior .....................................................................22

Care and Cleaning of the Interior...................................................22

Door Seal and Glass Cleaning.......................................................22

Removing Mineral Buildup.............................................................22

Storing the Washer ........................................................................22

Cleaning the Dispenser..................................................................23

Maintenance ................................................................................24-25

Cleaning the Water Inlet Filters......................................................24

Cleaning the Drain Pump Filter......................................................25

TROUBLESHOOTING GUIDE

Normal Sounds You May Hear .........................................................26

Before Calling for Service............................................................26-29

WARRANTY........................................................................................30

In the space below, record the date of purchase, model,

and serial number of your product. You will find the model

and serial number printed on an identification plate

located inside the washer door. Have these items of

information available whenever you contact Sears

concerning your product.

Model No.

Date of Purchase

Serial No.

Save these instructions and your sales receipt for future

reference.

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore

®

product is designed and manufactured for

years of dependable operation. But like all products, it

may require preventive maintenance or repair from time

to time. That's when having a Master Protection

Agreement can save your money and aggravation.

The Master Protection Agreement also helps extend the

life of your new product. Here's what the Agreement*

includes:

• Parts and labor needed to help keep products

operating properly under normal use, not just defects.

Our coverage goes well beyond the product

warranty. No deductible, no functional failure excluded

from coverage – real protection.

• Expert service by a force of more than 10,000

authorized Sears service technicians, which means

someone you can trust will be working on your product.

• Unlimited service calls and nationwide service, as

often as you want us, whenever you want us.

• "No-lemon" guarantee – replacement of your covered

product if four or more product failures occur within

twelve months.

• Product replacement if your covered product can't be

fixed.

• Annual Preventive Maintenance Check at your

request – no extra charge.

• Fast help by phone – we call it Rapid Resolution.

Phone support from a Sears representative on all

products. Think of us as a "talking owner's manual."

• Power surge protection against electrical damage due

to power fluctuations.

• $250 food loss protection annually for any food

spoilage that is the result of mechanical failure of any

covered refrigerator or freezer.

• Rental reimbursement if repair of your covered product

takes longer than promised.

• 10% discount off the regular price of any non-covered

repair service and related installed parts

Once you purchase the Agreement, a simple phone call

is all that it takes for you to schedule service. You can call

anytime day or night or schedule a service appointment

online.

The Master Protection Agreement is a risk-free purchase.

If you cancel for any reason during the product warranty

period, we will provide a full refund, or a prorated refund

anytime after the product warranty period expires.

Purchase your Master Protection Agreement today!

Some limitations and exclusions apply.

For prices and additional information in the U.S.A.

call 1-800-827-6655.

*Coverage in Canada varies on some items.

For full details call Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances,

garage door openers, water heaters, and other major

home items, in the U.S.A. or Canada call

1-800-4-MY-HOME

®

.

ENGLISH

3

SAFETY MESSAGES

IMPORTANT SAFETY INSTRUCTIONS

We have provided many important safety messages in this manual and on your appliance. Always read and obey

all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can result in property damage and/or serious bodily

harm or death.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

Failure to follow these safety instructions may result in property damage and/or

serious bodily harm or death.

Failure to follow these safety instructions may result in property damage and/or

serious bodily harm or death.

All safety messages will tell you what the potential hazard is, tell you how to reduce

the chance of injury, and tell you what can happen if the instructions are not followed.

To reduce the risk of fire, electric shock, or injury to

persons when using this appliance, follow basic

precautions, including the following.

• Before use, the washer must be properly installed as

described in this manual.

• Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline, dry

cleaning solvents, or other flammable or explosive

substances, as they give off vapors that could ignite or

explode.

• Do not add gasoline, dry cleaning solvents, or other

flammable or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

• Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.

If the hot water system has not been used for such a

period, before using the washer, turn ON all hot water

faucets and let the water flow from each for several

minutes. This will release any accumulated hydrogen

gas. As the gas is flammable, do not smoke or use an

open flame during this time.

• Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is

used near children.

• Before the washer is removed from service or

discarded, remove the door to prevent children from

climbing inside.

• Do not install or store the washer where it will be

exposed to the weather or freezing temperatures.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or

attempt any servicing other than as described in this

manual. We strongly recommend that any service be

performed by a qualified individual.

• See Installation Instructions for grounding requirements.

• ALWAYS follow the fabric care instructions supplied by

the garment manufacturer.

• Do not place items exposed to cooking oil in your

washer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load

to catch fire.

• Use fabric softeners or products to eliminate static only

as recommended by the manufacturer.

• This washer is not designed for maritime use or for

mobile installations such as in RVs, aircraft, etc.

• Turn OFF the water taps and unplug the washer if the

machine is to be left tor an extended period of time,

such as during vacations.

• Packaging material can be dangerous for children.

There is a risk of suffocation! Keep all packaging from

children.

• Always check the inside of the washer for foreign

objects before loading laundry. Keep the door closed

when not in use.

DANGER

WARNING

ENGLISH

4

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock, or injury to

persons when using this appliance, follow basic

precautions, including the following.

• Unplug the washer before cleaning to avoid the risk of

electric shock.

• Never use harsh chemicals, abrasive cleaners, or

solvents to clean the washer. They will damage the finish.

• Do not put oily or greasy rags or clothing on top of the

washer. These substances give off vapors that could ignite

the materials.

• Do not wash items that are soiled with vegetable or

cooking oil. These items may contain some oil after

laundering and may catch fire.

• Disconnect this appliance from the power supply

before attempting any user maintenance. Turning the

controls to the OFF position does not disconnect this

appliance from the power supply. Failure to follow this

warning can cause serious injury, fire, electrical shock, or

death.

• Do not combine detergents, fabric softeners, and other

laundry products from different manufacturers for use

in one load unless specified on the label.

• Do not mix chlorine bleach with ammonia or acids

such as vinegar. Follow package directions when

using laundry products. Incorrect usage can produce

poisonous gas, resulting in serious injury or death.

• Do not reach into the washer while parts are moving.

Before loading, unloading, or adding items, push in the

cycle selector knob and allow the drum to coast to a

complete stop before reaching inside.

Failure to follow this warning can cause serious injury, fire,

electrical shock, or death.

WARNING

• Refer to INSTALLATION INSTRUCTIONS for detailed

grounding procedures. Installation instructions are packed

in the washer for installer's reference. If the washer is

moved to a new location, have it checked and reinstalled by

a qualified service person. Failure to follow this warning can

cause serious injury, fire, electrical shock, or death.

• Do not, under any circumstances, cut or remove the

third (ground) prong from the power cord. Failure to

follow this warning can cause serious injury, fire, electrical

shock, or death.

• For personal safety, this appliance must be properly

grounded. Failure to follow this warning can cause serious

injury, fire, electrical shock, or death.

• The power cord of this appliance is equipped with a 3-

prong (grounding) plug which mates with a standard 3-

prong (grounding) wall outlet to minimize the possibility

of electric shock hazard from this appliance.

• This washer must be plugged into a 120VAC, 60Hz

grounded outlet. Failure to follow this warning can cause

serious injury, fire, electrical shock, or death.

• Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded. Failure to follow this warning can cause serious

injury, fire, electrical shock, or death.

• Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

Failure to follow this warning can cause serious injury, fire,

electrical shock, or death.

• Do not install on carpet. Install washer on a solid floor.

Failure to follow this warning can cause serious leak

damage.

• Do not remove grounding prong. Do not use an

adapter or extension cord. Plug into a grounded 3-

prong outlet. Failure to follow these warnings can cause

serious injury, fire, electrical shock, or death.

• The washer should always be plugged into its own

individual electrical outlet which has a voltage rating

that matches the rating plate. This provides the best

performance and also prevents overloading house wiring

circuits which could cause a fire hazard from overheated

wires.

• Never unplug your washer by pulling on the power

cord. Always grip plug firmly and pull straight out from the

outlet. Failure to follow this warning can cause serious

injury, fire, electrical shock, or death.

• Immediately repair or replace all power cords that have

become frayed or otherwise damaged. Do not use a

cord that shows cracks or abrasion damage along its

length or at either end. Consult with a qualified service

person. Failure to follow this warning can cause serious

injury, fire, electrical shock, or death.

• When installing or moving the washer, be careful not

to pinch, crush, or damage the power cord. Failure to

follow this warning can cause serious injury, fire, electrical

shock, or death.

• The washer must be installed and electrically

grounded by a qualified service person in accordance

with local codes to prevent shock hazard and assure

stability during operation.

• Washer is heavy. Two or more people may be needed

to install and move the appliance. Failure to do so can

result in back or other injury.

• Store and install the washer where it will not be

exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this

warning can cause serious leak damage.

• To reduce the risk of electric shock, do not install the

washer in humid spaces. Failure to follow this warning

can cause serious injury, fire, electrical shock, or death.

WARNING

ENGLISH

5

IMPORTANT SAFETY INSTRUCTIONS

GROUNDING REQUIREMENTS

WARNING

• Do not allow children to play on or in the washer.

Close supervision of children is necessary when the

washer is used near children. As children grow,

teach them the proper, safe use of all appliances.

Failure to comply with these warnings could result in

serious personal injuries.

• Destroy the carton, plastic bag, and other packing

materials after the washer is unpacked. Children

might use them for play. Cartons covered with rugs,

bedspreads, or plastic sheets can become airtight

chambers. Failure to comply with these warnings could

result in serious personal injuries.

IMPORTANT: Please read carefully.

TO CONNECT ELECTRICITY

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance

for electric current. This appliance is equipped with a cord

having an equipment-grounding conductor and grounding

plug. The plug must be plugged into an appropriate outlet

that is properly installed and grounded in accordance with

all local codes and ordinances.

Improper connection of the equipment-grounding

conductor can result in risk of electric shock. Check

with a qualified electrician or serviceman if you are in

doubt as to whether the appliance is properly

grounded. Do not modify the plug provided with the

appliance. If it does not fit the outlet, have a proper

outlet installed by a qualified electrician. Failure to

follow these warnings can cause serious injury, fire,

electrical shock, or death.

3-prong

grounding type

wall receptacle

3-prong

grounding

plug

Ensure proper

ground exists

before use.

• Keep laundry products out of children's reach. To

prevent personal injury, observe all warnings on

product labels. Failure to comply with these warnings

could result in serious personal injuries.

• Remove the door to the washing compartment to

avoid the danger of children or small animals

getting trapped inside before your washer is

removed from service or discarded. Failure to do so

can result in serious personal injury or death.

WARNING:

RISK TO CHILDREN

ENGLISH

6

FEATURES AND BENEFITS

KEY PARTS AND COMPONENTS

A

DETERGENT DISPENSER

There are four compartments, one each for prewash (not

used on this model) main wash, liquid bleach, and liquid

fabric softener.

B

CONTROL PANEL WITH LED DISPLAY

The easy-to-read LED display shows cycle options, settings,

cycle status, and estimated time remaining during operation.

NOTE: Sensors in the washer automatically detect the size

of the wash load to optimize washing time, based on the

selected cycle and options.

C

DIRECT-DRIVE MOTOR

The direct-drive motor provides improved performance

and reliability while increasing energy efficiency.

(Motor is not visible.)

D

LARGE-CAPACITY STAINLESS STEEL DRUM

The ultra-large stainless steel drum offers extreme

durability and is tilted to improve efficiency and allow

easier access for large items.

E

EASY-ACCESS LOCKING DOOR

The extra-large door locks during operation and has a

delay feature to prevent the door from being opened until

it is safe to do so.

F

FILTER ACCESS PANEL

Provides easy access to the drain pump filter, which

allows you to clean the filter or retrieve lost items without

a service call.

G

LEVELING FEET

Four leveling feet (two in the front and two in the back)

adjust to improve washer stability on uneven floors. Feet

are adjusted and locked in place using the adjusting

wrench included with the washer.

H

HIGH-EFFICIENCY STEAM CYCLES

During high-efficiency STEAM cycles, the steam nozzle

injects fabrics with hot steam to gently remove tough

stains.

Optional Accessories

Drain Hose Extension

P/N 5215ER2002K D26 17002 (White)

D26 17008 (Ginger)

D26 17009 (Chili Pepper)

Canada only

D26 18992 (Titanium)

Stacking kit (For dryer)

Hot and Cold

Water Hoses

Wrench (for removing

shipping bolts and

adjusting and

locking leveling feet)

Elbow Bracket

(for securing

drain hose

Tie Strap

(for securing

drain hose

Caps (4)

(for covering

shipping bolt holes)

Non-skid pads

Hot and Cold

Water Inlets

Power

Cord

Drain

Hose

Rear of Washer

Shipping Bolts/Retainers (4)

NOTE: Bolts/retainers MUST be removed prior

to operation. Keep for future use. See page 8.

Included Accessories

ENGLISH

7

INSTALLATION REQUIREMENTS

KEY

DIMENSIONS AND SPECIFICATIONS

CHOOSE THE PROPER LOCATION

FLOORING

CLEARANCES

Description Front-Loading Washer

Rated Voltage/Frequency 120VAC, 60Hz

Dimensions 27" (W) X 29

3

/4" (D) X 38

11

/16" (H), 51

1

/8" (D, door open)

68.6 cm (W) X 75.6 cm(D) X 98.3 cm(H), 129.8 cm (D, door open)

Net Weight 190.7 lb. (86.5 kg)

WARNING

• Washer is heavy! Two or more people are required

when moving and unpacking the washer. Failure to do so

may result in damage to property or serious bodily harm.

• Store and install the washer where it will not be

exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this warning

can cause serious injury, fire, electrical shock, or death.

• Properly ground washer to conform with all governing

codes and ordinances. Failure to follow this warning can

cause serious injury, fire, electrical shock, or death.

• To reduce the risk of electric shock, do not install the

washer in humid spaces. Failure to follow this warning can

cause serious injury, fire, electrical shock, or death.

• The base opening must not be obstructed by carpeting

when the washer is installed on a carpeted floor.

• Do not remove ground prong. Do not use an adapter or

extension cord. Plug into a grounded 3-prong outlet.

Failure to follow this warning can cause serious injury, fire,

electrical shock, or death.

• The power outlet must be within 60 in. (1.5 m) of either side

of the washer.

• The appliance and outlet must be positioned so that the

plug is easily accessible.

• Do not overload the outlet with more than one appliance.

• The outlet must be grounded in accordance with current

wiring codes and regulations.

• Time-delay fuse or circuit breaker is recommended.

NOTE: It is the personal responsibility and obligation of the

product owner to have a proper outlet installed by a qualified

service person.

NOTE: Please note that the floor must be strong and rigid

enough to support the weight of the washer, when fully

loaded, without flexing or bouncing. If your floor has too

much flex in it, you may need to reinforce it to make it more

rigid. A floor that is adequate for a top-loading washer may

not be rigid enough for a front loading washer, due to the

difference in the spin speed and direction. If the floor is not

solid, your washer may vibrate and you may hear and feel

the vibration throughout your house.

Allow at least 21

1

/4 in. (54 cm) in front of the washer to open

the door.

To ensure sufficient clearance for water lines and airflow,

allow minimum clearances of at least 1 in. (2.5 cm) at the

sides and 4 in. (10 cm) behind the unit. Be sure to allow for

wall, door, or floor moldings that may increase the required

clearances.

• To minimize noise and vibration, the washer MUST be

installed on a solidly constructed floor. See the NOTE at

right.

• Allowable slope under the entire washer is a maximum 1"

difference from side to side or from front to back.

• Carpeting and soft tile surfaces are not recommended.

• Never install the washer on a platform or weakly supported

structure.

Power Outlet

21

1

/3"

(54.2 cm)

29

3

/4"

(75.6 cm)

4"

(10 cm)

1"

(2.5 cm)

1"

(2.5 cm)

27"

(68.6 cm)

51

1

/

8"

(129.8 cm)

ENGLISH

8

INSTALLATION INSTRUCTIONS

UNPACKING AND REMOVING SHIPPING BOLTS

When removing the washer from the carton base, be sure to

remove the foam tub support in the middle of the carton

base. See drawing below.

If you must lay the washer down to remove the base

packaging materials, always protect the side of the washer

and lay it carefully on its side. DO NOT lay the washer on its

front or back.

To prevent internal damage during transport, the washer is

equipped with 4 shipping bolts and plastic retainers.

IMPORTANT:

• These shipping bolts and retainers MUST NOT be

removed until just before moving the washer into its final

position.

• These bolts and retainers MUST be removed before

operating the washer.

• Failure to remove shipping bolts and retainers may cause

severe vibration and noise, which can lead to permanent

damage to the washer.

NOTE: The power cord is secured to the back of the washer

with a shipping bolt to help prevent operation with shipping

bolts in place.

1. Starting with the bottom 2 shipping bolts, use the included

wrench to fully loosen all 4 shipping bolts by turning them

counterclockwise.

2. Remove the bolt assemblies by wiggling them slightly

while pulling.

3. Locate the four hole caps included in the accessory pack

and install them in the shipping bolt holes.

NOTE: Save the bolt assemblies for future use. To prevent

damage to internal components, the bolt assemblies must

be installed when transporting the washer.

Foam Tub

Support

Carton

Base

Power

Cord

Shipping

Bolts

Shipping

bolts

Hole Cap

ENGLISH

9

INSTALLATION INSTRUCTIONS

CONNECTING THE WATER LINES

3. Connect the water supply hoses to the HOT and COLD

water faucets tightly by hand and then tighten another

2/3 turn with pliers. Turn ON the water faucets and check

for leaks.

2. Attach the red, hot water line to the hot water inlet on the

back of the washer. Attach the blue, cold water line to the

cold water inlet on the back of the washer. Tighten the

fittings securely.

NOTE: Be careful not to cross-thread the hose fittings

since this will damage the valve and could result in

property damage from leaks.

For cold water

Water Inlets

For hot water

Water Tap

• IMPORTANT: Use new hoses when installing the washer.

Do NOT reuse old hoses.

• IMPORTANT: Use ONLY the inlet hoses provided with this

laundry product. Aftermarket hoses are not guaranteed to

fit or function correctly. Other hoses may not tighten

correctly and could cause leaks. Subsequent damage to

product or property will not be covered under the terms of

the product warranty.

• Water supply pressure must be between 14.5 psi and 116

psi (100~800 kPa). If the water supply pressure is more

than 116 psi, a pressure reducing valve must be installed.

• Periodically check the hose for cracks, leaks, and wear,

and replace the hose if necessary.

• Make sure that the water lines are not stretched, pinched,

crushed, or kinked.

• The washer should never be installed or stored in a

location subject to freezing temperatures. Damage to the

water lines and internal mechanisms of the washer can

result. If the washer was exposed to freezing temperatures

prior to installation, allow it to stand at room temperature

for several hours before use and check for leaks prior to

operation.

1. Inspect the threaded fitting on each hose and make sure

there is a rubber seal in place in both ends.

Water Hose

(to water inlet

on washer)

Rubber Seal

Water Hose

(to tap)

ENGLISH

10

INSTALLATION INSTRUCTIONS

CONNECTING THE DRAIN HOSE

CONNECT TO THE POWER SUPPLY

Drain Hose Extension

P/N 5215ER2002K

NOTE:

A drain hose extension kit is

available if the drain hose is not

long enough. Do not extend

drain hose more than 6 feet, as

this will cause poor draining

resulting in poor wash and spin

performance.

• The drain hose should always be properly secured.

Failure to properly secure the drain hose can result in

flooding and property damage.

• Do not install the end of the drain hose higher than 96 in.

(243.8 cm) above the bottom of the washer.

• The drain must be installed in accordance with any

applicable local codes and regulations.

• Make sure that the drain hose is not stretched, pinched,

crushed, or kinked.

Install the end of the drain hose into the elbow bracket. Do

not extend the drain hose more than 4 inches past the end

of the elbow bracket. Use tie strap to secure the drain hose

in place.

NOTE:

• Total height of the hose end should not exceed 96 in.

(243.8 cm) from the bottom of the washer.

• The drain hose should be inserted no more than 8–12

inches into the standpipe.

• Extending the drain hose more than 4 inches past the end

of the elbow bracket can cause mold or microorganisms to

spread to the inside of the washer.

Drain Hose

Elbow Bracket

Tie

Strap

Option 1: Standpipe

The elbow bracket should be installed near the end of the

drain hose. Hang the end of the drain hose over the side of

the laundry tub. Use tie strap to secure the drain hose in

place.

Insert the end of the drain hose into the floor drain.

If possible, secure the hose to prevent it from moving or

coming out of the drain.

Washer should be plugged into a 120-VAC, 60-Hz grounded

3-prong outlet.

Plug in the washer.

Drain Hose

Tie Strap

Elbow Bracket

Laundry Tub

Option 2: Laundry Tub

Drain Hose

Floor Drain

Option 3: Floor Drain

ENGLISH

11

INSTALLATION INSTRUCTIONS

LEVELING THE WASHER

Raise

Level

Leveling Feet

Leveling

Feet

Lower

Tighten all 4 lock nuts

securely using the

wrench.

The drum of your new washer spins at very high speeds.

To minimize vibration, noise, and unwanted movement,

the floor must be a level, solid surface.

NOTE: Adjust the leveling feet only as far as necessary to level

the washer. Extending the leveling feet more than necessary

can cause the washer to vibrate.

NOTE: Before installing the washer, make

sure the floor is clean, dry and free of dust,

dirt, water and oils so the washer feet can

not slide easily. Leveling feet that can move

or slide on the floor can contribute to excess

vibration and noise due to poor contact

with the floor. See INSTALLATION OF

NON-SKID PADS below for more

information.

NOTE: If a drip pan must be used, take extra care to follow the

instructions provided with the drip pan and make sure the

leveling feet are adjusted for firm and even contact with the

pan. Use of drip pans and failure to properly level the machine

may result in increased vibration and noise during operation.

• All four leveling feet must rest solidly on the floor. Attempt to

rock the washer from corner to corner to make sure that all

four leveling feet are in firm contact with the floor.

1. Position the washer in the final location, taking special care

to not pinch, strain, or crush the water and drain lines. Place

a level across the top of the washer.

2. Loosen the locknuts on all 4 leveling feet with the wrench

until you can adjust the feet. Use the wrench to turn the feet

clockwise to raise the washer and counterclockwise to lower

the washer. Using a level, adjust the feet until the washer is

level from side to side and front to back. Make sure all 4 feet

are in firm contact with the floor.

NOTE: If you are installing the washer on the optional pedestal,

the washer leveling feet should be fully retracted. Use the

leveling feet on the pedestal to level the washer.

3. Once the washer is level from side to side and front to

back, use the adjusting wrench to tighten all four lock nuts

securely to prevent the legs from getting out of

adjustment during operation.

Make sure that all 4 leveling feet are in firm contact with

the floor.

NOTE: To make sure that the washer is properly level, run

the washer with a test load: place a medium-sized load of

laundry in the machine. Then press POWER, select

EXPRESS WASH, and then press the START/PAUSE

button. See the following sections for additional information

on cycle selection and operation. Verify that the washer

does not rock or vibrate excessively during the spin cycle. If

the washer vibrates or shakes, adjust the leveling feet, while

the washer is spinning, until the vibrations are reduced to a

minimum.

Some floor surfaces are too slippery to prevent the washer

from moving on the floor during heavily unbalanced loads.

While it is normal for an occasional load to be out of

balance, excess noise and vibration can result from the

washer moving out of position. If these conditions are

encountered, follow the instructions below for installation of

the non-skid pads. These pads will help prevent the washer

from moving during heavy out of balance conditions thereby

reducing noise and vibration.

Non-skid pads

INSTALLATION OF NON-SKID PADS

(optional)

 Place the pads under both front feet.

This side up

Stick adhesive side to floor

Remove backing

ENGLISH

CONTROL PANEL FEATURES

HOW TO USE

12

A

POWER (ON/OFF) BUTTON

Press to turn the washer ON. Press again to turn the

washer OFF.

NOTE: Pressing the POWER button during a cycle will

cancel that cycle and any load settings will be lost.

The door will unlock after a brief pause unless the

water level or temperature is too high.

E

SPECIAL CYCLE AND OPTION BUTTONS

These buttons are used to activate special cycles or

options. See page 21 for details.

F

TIME AND STATUS DISPLAY

The display shows the estimated time remaining, cycle

status, and door lock status. See page 18 for a

complete description.

G

ADD STEAM BUTTON

Press the ADD STEAM button to add steam to the

selected cycle for added cleaning power.

NOTE: Steam can only be added to the following

cycles : Steam Refresh, Normal/Casual,

Bulky/Bedding, Kids Wear, Heavy Duty and Whitest

Whites. See page 20 for details.

B

CYCLE SELECTOR KNOB

Turn this knob to select the desired cycle. Once the

desired cycle has been selected, the standard presets

will be shown in the display. These settings can be

adjusted using the cycle setting buttons anytime before

starting the cycle. (See the cycle guide on page 14 for

allowable settings. To protect your fabrics, not all

settings are allowed in all cycles.)

C

START/PAUSE BUTTON

Press this button to start the selected cycle.

If the washer is running, use this button to pause the

cycle without losing the current settings.

NOTE : If you do not press the START/PAUSE button

within 4 minutes of selecting a cycle, the washer

automatically turns OFF.

D

CYCLE MODIFIER BUTTONS

Use these buttons to adjust the desired cycle options

for the selected cycle. The lights above the buttons

show the current selection. See page 19 for a

complete description.

NOTE : Not all settings are available on all cycle

selections. See chart on page 14 for details.

WARNING:

To reduce the risk of fire, electric shock, or injury to persons, read and follow this

entire Use & Care Guide, including the Important Safety Instructions, before operating this washer.

AGH

FE E

B C D

H

DISPENSER

Dispenser drawer. This drawer contains the

compartments for detergent and additives.

See pages 16 -17 for complete information.

ENGLISH

OPERATING THE WASHER

HOW TO USE

13

7

BEGIN CYCLE

Press the START/PAUSE button to begin the cycle. Once the cycle has been

started, pressing the START/PAUSE again will pause the washer and retain

the existing settings for up to 4 minutes.

3

TURN ON THE WASHER

Press the POWER button to turn ON the washer. The lights around the Cycle

Selector Knob will illuminate and a chime will sound. Refer to page 12.

4

SELECT A CYCLE

Turn the Cycle Selector Knob either direction to select the desired cycle. The

preset Wash/Rinse Temperature, Spin Speed, Soil Level, and Option settings

for that cycle will be shown. Refer to page 12.

5

SELECT CYCLE MODIFIERS

Default settings for the selected cycle can now be changed if desired. This

can be done using the cycle modifier buttons as shown on page 19

(Wash/Rinse, Spin Speed, Soil Level, and Chime).

NOTE: To protect your fabrics, not all modifiers are available on all cycles.

2

ADD DETERGENT AND OTHER PRODUCTS

Open the dispenser drawer and add detergent to the main wash

compartment in the dispenser drawer. Add bleach and fabric softener as

desired. See pages 16 and 17 for important information on detergents and

dispenser use.

SOFTENER

MAX

6

SELECT CYCLE OPTIONS

Cycle options can also be added using the option buttons as shown on page

20 and 21 (Stain Treat, 2

nd

Rinse, Control Lock, Add Steam, Clean Washer

and Delay Start).

NOTE: Not all options are available on all cycles.

1

SORT LAUNDRY AND LOAD WASHER

Refer to page 15.

ENGLISH

14

HOW TO USE

CYCLE GUIDE

The cycle guide below shows the default settings, available options and recommended fabric types for each

cycle. Allowable modifier adjustments are shown below the default setting for each cycle.

= Available option

= Default setting

NOTE: To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with every cycle.

A chime will sound and the LED will not light if the selection is not allowed.

NOTE: The washer automatically adjusts the wash time for the amount of laundry, water pressure, water heating time and

other operating condition.

Modifiers Options

STAIN

TREAT

2

nd

RINSE

ADD

STEAM

Wash/Rinse

Temperature

Fabric or

Load Type

Cycle Spin Speed Soil Level

Steam

Refresh

Dress shirts, Blouses

(Load up to 5 garments)

Normal/

Casual

Cotton, linen, towels,

shirts, sheets, jeans,

mixed loads

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

High

Extra High

No Spin

Low

Medium

Heavy

Light

Normal

Kids wear

Kids Wear

Warm/Cold

Warm/Warm

Hot/Cold

Cold/Cold

Low

Medium

No Spin

Normal

Heavy

Light

Bulky/

Bedding

Large items such as

blankets and comforters

Extra Hot/Cold High

Extra High

No Spin

Low

Medium

Normal

Heavy

Light

Heavy Duty

Heavy soiled Cotton

Fabrics

Warm/Cold

Warm/Warm

Hot/Cold

Cold/Cold

High

Extra High

No Spin

Low

Medium

Normal

Heavy

Light

Cold Clean

Small loads of cotton, linen,

towels, shirts, sheets,

jeans, mixed loads

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

High

Extra High

No Spin

Low

Medium

Normal

Heavy

Light

Sanitize

Heavily soiled items, such

as work clothes, diapers,

etc.

Cold/Cold High

Extra High

No Spin

Low

Medium

Normal

Light

Delicates

Dress shirts/blouses

nylons, sheer or lacy

garments

Warm/Cold

Warm/Warm

Hot/Cold

Cold/Cold

Extra High

No Spin

Low

Medium

High

Heavy

Light

Normal

Whitest

Whites

White Fabrics

Cold/Cold

Warm/Cold

Warm/Warm

Medium

No Spin

Low

Normal

Heavy

Light

Express

Wash

Lightly soiled clothing and

small loads

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

Extra High

No Spin

Low

Medium

High

Light

Normal

Heavy

Wash

Motion

Display

Time (Min.)

Cycle

50-59

20

59

91-97

74-80

69-75

20

57-63

101-107

42

NOTE: These cycles use various wash motions to enhance cleaning and/or fabric care performance.

These wash motions may sound different at different stages of the wash cycle. This is normal.

ENGLISH

SORTING WASH LOADS

HOW TO USE

15

Many articles of clothing include a fabric care label. Using

the chart below, adjust the cycle and options selections to

care for your clothing according to the manufacturer’s

recommendations.

Fabric Care Labels

• Check all pockets to make sure that they are empty.

Items such as clips, matches, pens, coins, and keys can

damage both your washer and your clothes.

• Close zippers, hooks, and drawstrings to prevent these

items from snagging or tangling on other clothes.

• Pretreat heavily stained areas for best results.

• Combine large and small items in a load. Load large items

first.

• Large items should not be more than half of the total wash

load.

• The washer can be fully loaded, but the drum should not be

tightly packed with items. The door of the washer should

close easily.

• To prevent an out-of-balance load, do not wash single

items. Add one or two similar items to the load. Large, bulky

items, such as a blanket, comforter, or bedspread, should

be washed individually.

• Do not wash or spin waterproof items, such as rain coats,

sleeping bags, etc.

• When unloading the washer, check under the door seal for

small items.

NOTE: Make sure the door seal area is clear when closing

the door. Overloading the washer can cause items to get

caught between the door and the seal. This can damage both

the items and the seal.

Loading the Washer

For the best washing results and to reduce the possibility of

damage to the clothing, care should be taken to sort the

clothing into loads that are made up of similar items. Mixing

different fabric types and/or soil levels can result in poor wash

performance, color transfer or discoloration, fabric damage or

linting. Fabrics should be sorted into groups as described

below.

Colors

Sort articles by color. Wash dark clothes together in a

separate load from light colors or whites. Mixing dark clothes

with light clothes can result in dye transfer or discoloration of

the lighter clothes.

Soil Level

Wash heavily soiled clothes together. Washing lightly soiled

clothes in the same load with heavily soiled clothes could

result in poor wash performance for the lightly soiled clothing.

Fabric Type

Delicate articles should not be mixed with heavier or sturdier

fabric types. Washing delicates in a load with heavy fabrics

can result in damage to the more delicate fabrics. Washing

heavier fabrics in a delicate load can result in poor wash

performance for the heavier fabrics and possible damage to

the delicates.

Lint Type

Some fabrics attract and bind lint to them while others give off

lint in the laundry process. Avoid mixing these lint collectors

and lint producers in the same load. Mixing these fabrics will

result in pilling and linting on the lint collectors. (For example,

lint collector – knit sweater; lint producer – terrycloth towels)

• DO NOT OVERLOAD THE DRUM

• MAKE SURE CLOTHING IS NOT

CAUGHT IN THE DOOR GASKET

Grouping Similar Items

Sort Laundry...

by Colors

Whites

Lights

Darks

by Soil

Heavy

Normal

Light

by Fabric

Delicates

Easy Care

Sturdy

by Lint

Lint Producer

Lint Collector

ENGLISH

16

HOW TO USE

ABOUT THE DISPENSER

Liquid Chlorine

Bleach

Compartment

Liquid Fabric

Softener

Compartment

Prewash

Compartment

(This compartment is

not used on this model.)

Main Wash

Compartment

The automatic dispenser consists of four compartments

which hold:

• Liquid chlorine bleach.

• Liquid fabric softener.

• Liquid or powdered detergent for prewash.

(This compartment is not used on this model.)

• Liquid or powdered detergent and color-safe bleach for

main wash.

The dispenser drawer has a compartment that is labeled

"Prewash". However, this model does not include a prewash

option. Do not put detergent in this compartment. Detergent

in this compartment will not be dispensed and will need to be

manually cleaned out.

Pre-Wash Detergent Compartment

This compartment holds liquid chlorine bleach, which will be

dispensed automatically at the proper time during the wash

cycle.

• Do not add powdered or liquid color-safe bleach to this

compartment. The bleach compartment is designed to

dispense liquid chlorine bleach only. Powdered or liquid

color-safe bleach will not dispense properly.

• Always follow the manufacturer's recommendations when

adding bleach. Do not exceed the maximum fill line since

this can cause the bleach to be dispensed immediately

causing damage to fabrics. Using too much bleach can

damage fabrics.

• Never pour undiluted liquid chlorine bleach directly onto the

load or into the drum. Fabric damage can occur.

Liquid Bleach Compartment

This compartment holds liquid fabric softener, which will be

automatically dispensed during the final rinse cycle.

Never exceed the manufacturer's recommendations when

adding softener. Using too much fabric softener can result in

buildup in clothing and the washer. Either powdered or liquid

fabric softener may be used.

• Always follow the manufacturer's recommendations when

adding fabric softener. Do not exceed the maximum fill line.

Using too much fabric softener may stain clothes.

• Dilute concentrated fabric softeners with warm water.

Do not exceed the maximum fill line.

• Never pour fabric softener directly onto the load or into the

drum.

Fabric Softener Compartment

This compartment holds laundry detergent for the main wash

cycle; this detergent is added to the load at the beginning of

the cycle. Always use HE (High-Efficiency) detergent with

your washing machine. Either powdered or liquid detergent

may be used.

Never exceed the manufacturer's recommendations when

adding detergent. Using too much detergent can result in

detergent buildup in clothing and the washer.

NOTE: Liquid or powdered color-safe bleach may be added

to the main wash compartment with detergent of the same

type. DO NOT add liquid or powdered color-safe bleach to

the bleach dispenser. DO NOT mix liquid and powdered

cleaning agents within the same compartment.

Main Wash Detergent Compartment

ENGLISH

To add detergent, bleach, and fabric softener to the

automatic dispenser:

Open the dispenser drawer.

Load the laundry products into the appropriate

compartments.

Close the drawer before starting the cycle.

NOTE: It is normal for a small amount of water to remain in

the bleach and softener compartments at the end of the

cycle.

IMPORTANT: Do not place or store laundry products, such

as detergent, bleach, or liquid fabric softener, on top of your

washer or dryer. Wipe up any spills immediately. These

products can damage the finish and controls.

NOTE: Do not put detergent or other laundry products in the

Prewash compartment. This compartment is not used on this

model

Filling the Dispenser

17

HOW TO USE

DETERGENT AND DISPENSER USE

IMPORTANT: Not all detergents are the same. Careful

attention must be paid to the amount of detergent used to

avoid overusing, poor rinsing and detergent buildup in

clothing, and residue buildup that can contribute to odors in

the machine. NEVER use a cup or scoop other than that

supplied by the manufacturer of the detergent you are using.

Never use more than the maximum amount recommended

by the manufacturer of the detergent.

While HE detergents are designed for this type of washing

machine, care must be used when measuring the detergent.

For most normal loads, no more than 1/2 to 3/4 of a cup or

scoop of HE detergent should be used.

NOTE: Extra care must be exercised when using 2X and 3X

concentrated detergents because even a little bit extra can

contribute to the problems mentioned above.

NOTE: Detergents designated as HE-COMPATIBLE may not

provide optimal results.

The normal amount needed for average loads is less than

1/2 of the recommended maximum. Use less detergent for

soft water, light soil or smaller loads. Never use more than

the maximum amount recommended by the detergent

manufacturer.

MAXIMUM

LIQUID

DETERGENT

For proper wash performance, always measure the

detergent using the measure provided with the detergent

by the manufacturer.

POWDERED

DETERGENT

Normal load amount

1

2

3

HE detergents produce fewer suds, dissolve more efficiently

to improve washing and rinsing performance, and help to

keep the interior of your washer clean.

Using non-HE detergent may cause oversudsing and

unsatisfactory performance which could result in error codes,

cycle failure, and machine damage.

A Word About Detergents

Designed to use only

HE (High-Efficiency) detergent

IMPORTANT: Your washing machine is designed for use

with only High-Efficiency (HE) detergents. HE detergents are

formulated specifically for front-load washers and contain

suds-reducing agents. Always look for the HE symbol when

purchasing detergent.

ENGLISH

18

HOW TO USE

TIME AND STATUS DISPLAY

A

C

D

B

A

ESTIMATED TIME REMAINING

When the START/PAUSE is pressed, the washer

automatically detects the wash load (weight) and

optimizes the washing time, based on the selected cycle

and options. The display will then indicate the estimated

time remaining for the selected wash cycle.

NOTE:

• The time shown is estimated. For example, the time

displayed may pause for a period of time while the

machine is heating the water or balancing the load.

Under certain conditions, the machine can pause for

extended periods of time.

• Estimated time is based on normal operating conditions.

Several external factors (room temperature, incoming

water temperature, etc.) also affect the length of

estimated time vs. actual time.

C

CYCLE STATUS INDICATOR

These status LEDs illuminate to indicate which portion of

the cycle is currently running. A blinking light indicates the

active portion of the cycle. When that portion is complete,

the light will remain steady.

D

DOOR LOCK INDICATOR

Indicates that the door is locked. The washer door will lock

while the washer is operating. The door can be unlocked

by pressing the START/PAUSE to pause the washer.

NOTE:

• If the temperature in the washer is too high, the door

cannot be unlocked until the washer has cooled.

• If the water level is too high, the door will not unlock. To

drain the water, press POWER, then press the SPIN

SPEED button without selecting a cycle. Press

START/PAUSE and the water will be drained and the

clothes will be spun out. Do not try to force the door

open, as it will damage the door.

B

LOAD-SENSING INDICATOR

This light will illuminate at the beginning of the cycle while

the control measures the size of the load. Once the size

has been determined, the control will adjust the cycle for

optimum performance. Estimated time remaining will not

be displayed until the load size has been determined and

may be different for each load.

The time and status display shows the estimated time remaining, cycle progress, and door lock status.

ENGLISH

19

HOW TO USE

CYCLE MODIFIER BUTTONS

A B C D

A

WASH/RINSE

Selects the wash and rinse temperature combination for

the selected cycle. Press the WASH/RINSE button until

the indicator light for the desired setting is lit.

• Your washer features a heating element to boost the hot

water temperature for Extra Hot settings.

This provides improved wash performance at normal

water heater settings.

• Select the water temperature suitable for the type of load

you are washing. Follow the garment fabric care labels

for best results.

• Warm rinses are regulated at approximately 86°F (30°C).

• Warm rinses leave the clothes drier than cold rinses, but

will result in increased energy consumption and greater

wrinkling of clothes.

• Cold rinses use less energy. The actual rinse

temperature depends on the temperature of the cold

water at the faucet.

B

SPIN SPEED

This extracts more water from clothes, reducing drying

time and saving energy.

Press the SPIN SPEED button until the indicator light for

the desired setting is lit. Some fabrics, such as delicates,

require a slower spin speed.

The Drain & Spin cycle:

1. Press the POWER button to turn ON the washer.

2. Press the SPIN SPEED button to select the desired

spin speed. For drain only, select the NO SPIN option.

3. Press the START/PAUSE button. The water will be

drained and the clothes will be tumbled before the

spin routine begins.

C

SOIL LEVEL

Adjusts the selected cycle to allow more time for heavily

soiled clothes or less time for lightly soiled clothes.

Press the SOIL LEVEL button until the indicator light for

the desired setting is lit.

D

CHIME

Press repeatedly to adjust the volume of the chime.

You may turn the end-of-cycle chime and keypad tones

on or off with the CHIME button.

Each cycle has default settings that are selected

automatically. You may also customize these settings using

the cycle modifier buttons. Press the button for the desired

modifier until the indicator light for the desired value is lit.

The washer automatically adjusts the water level for the type

and size of wash load for best results and maximum

efficiency. Due to the high-efficiency nature of this product,

water levels may be much lower than expected. This is

normal operation and cleaning/rinsing performance will not

be compromised.

NOTE: To protect your garments, not every wash/rinse

temperature, spin speed, soil level, or option is available with

every cycle. A chime will sound and the LED will not light if a

selection is not allowed. See the Cycle Guide on page 14 for

details.

ENGLISH

STEAM CYCLES AND OPTIONS

HOW TO USE

ADD STEAM Option

20

Steam cycles include the Steam Refresh,

Normal/Casual, Bulky/Bedding, Kids Wear,

Heavy Duty and Whitest Whites. Adding

steam to these cycles provides superior

cleaning performance while reducing

energy and water consumption.

By using a hot steam spray from above and cooler water

below, fabrics get the cleaning benefits of a super hot wash,

without the energy usage or potential damage to fabrics.

CAUTION:

The door may become quite warm during steam cycles. This

is normal.

Do not attempt to override the door lock mechanism or reach

into the washer during a steam cycle. Steam can cause

severe burns.

IMPORTANT NOTES ABOUT STEAM CYCLES:

• Steam may not be visible during the steam cycles. This is

normal.

• Do not use steam with delicate fabrics such as wool, silk, or

easily discolored fabrics.

STEAM REFRESH uses the power of steam alone to quickly

reduce wrinkles and odor in fabrics. It brings new life to

wrinkled clothes that have been stored for an extended time

and makes heavily wrinkled clothes easier to iron. STEAM

REFRESH can also be used to help reduce odors in fabrics.

After the STEAM REFRESH cycle is complete, the washer

will tumble the clothes for up to 30 minutes to prevent

clothes from becoming wrinkled again.

After removing clothes from the STEAM REFRESH cycle,

they may feel slightly damp. If desired, hang clothes on a

hanger for a few minutes before wearing.

• The STEAM REFRESH cycle is not recommended for use

with 100% cotton clothing. Best results can be obtained

with 70/30 cotton/poly blend fabrics.

• Remove stains from clothing before using the STEAM

REFRESH cycle; the high heat could cause stains to set

permanently.

• Do not use STEAM REFRESH with the following items:

wool, blankets, leather jackets, silk, wet clothes, lingerie,

foam products, or electric blankets.

• Best results are achieved when articles are of similar size

and fabric type. Do not overload.

1

2

3

4

Turn on the washer and turn the cycle selector knob to

select a cycle that allows the steam option.

Press the ADD STEAM button. The washer will

automatically adjust the cycle settings.

Set any other desired options.

Press the START/PAUSE button to start the cycle.

To ADD STEAM to a cycle:

1

2

3

4

Turn on the washer and turn the cycle selector knob to

select the STEAM REFRESH cycle.

Load up to 5 items and close the door.

NOTE: If there is any moisture inside the drum, such as

from a previous wash cycle, wipe the drum dry with a

towel before adding clothes.

Press the ADD STEAM button until the correct number

of items is shown in the display.

No other options need to be set. The cycle is designed

to refresh from 1 to 5 garments.

Press the START/PAUSE button to start the cycle.

To use the STEAM REFRESH cycle:

Using the STEAM REFRESH Cycle

La page charge ...

LG 40445 Le manuel du propriétaire

LG 40445 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents