Excell EPW2123100 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
PRESSURE WASHER
OPERATION MANUAL
for model EPW2123100
IMPORTANT: Please make certain that the person who is to use this equipment carefully reads
and understands these instructions before operating.
Part No. E110166// Rev. 206/26/2018 PRINTED IN CHINA
Record All Information and attach sales
receipt here for future reference:
Purchase Date:__________________________
Serial #: ________________________________
Questions? 1-888-895-4549
Refer to the website for electronic
manual and parts book.
www.powermate.com
TABLE OF CONTENTS
Safety Guidelines/Denitions ........................... 2
Consumer Safety Information .......................... 2
Important Safety Instructions .......................... 2
Safety Features ............................................... 6
Specications .................................................. 6
Assembly instructions ..................................... 7
Spray Nozzle Selection .................................... 9
Before Operation ............................................. 9
Engine and Pump Features ........................... 10
Operating Connections.................................. 10
Operating Instructions ................................... 11
Start-Up Procedure ....................................... 11
Chemical Injection ......................................... 11
Cleaning Techniques ..................................... 12
End of Cleaning Operation ............................ 12
Maintenance .................................................. 13
Storage .......................................................... 14
Warranty ........................................................ 15
Troubleshooting Guide .................................. 16
Français ......................................................... 17
Español .......................................................... 33
Copyright © 2017 MAT Industries, LLC
2 - ENG
SAFETY GUIDELINES - DEFINITIONS
• SAVE ALL INSTRUCTIONS
This manual contains information that is important for you to know and understand. This information
relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this
information, we use the symbols below. Please read the manual and pay attention to these symbols.
DANGER
Indicates an imminently hazardous situation which, if not
avoided , WILL result in DEATH OR SERIOUS INJURY.
CAUTION
Indicates a potentially hazardous situation which, if not
avoided, MAY result in MINOR OR MODERATE INJURY.
WARNING
Indicates a potentially hazardous situation which, if
not avoided, COULD result in DEATH OR SERIOUS
INJURY.
NOTICE
Indicates a potentially hazardous situation which, if
not avoided, MAY result in PROPERTY DAMAGE.
CONSUMER SAFETY INSTRUCTIONS
• SAVE ALL INSTRUCTIONS
WARNING
This product may not be equipped with a spark arresting mufer. If the product is not
equipped and will be used around ammable materials, or on land covered with materials such as agricultural
crops, forest, brush, grass, or other similar items, then an approved spark arrester must be installed and is
legally required by the state of California. It is a violation of California statutes section 13005(b) and/or sections
4442 and 4443 of California Public Resources Code, unless the engine is equipped with a spark arrester, as
dened in section 4442, and maintained in effective working order. Spark arresters are also required on some
U.S. Forest Service land and may also be legally required under other statutes and ordinances.
WARNING: CONTAINS LEAD. MAY BE HARMFUL IF EATEN OR CHEWED. MAY GENERATE DUST
CONTAINING LEAD. WASH HANDS AFTER USE. KEEP OUT OF REACH OF CHILDREN.
WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING LEAD, WHICH IS KNOWN
TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE
HARM. FOR MORE INFORMATION GO TO WWW.P65WARNINGS.CA.GOV.
IMPORTANT SAFETY INSTRUCTIONS
• SAVE ALL INSTRUCTIONS
WARNING
Do not operate this unit until you have read and understand this Operator's Manual and
the Engine Owner's Manual for Safety, Operation, and Maintenance Instructions.
READ AND SAVE THESE INSTRUCTIONS
Copyright © 2017 MAT Industries, LLC
3 - ENG
WHAT CAN HAPPEN HOW TO PREVENT IT
• Spilled gasoline and its vapors can become ignited from
cigarette sparks, electrical arcing, exhaust gases and hot
engine components such as the mufer.
• Shut off engine and allow it to cool before adding fuel to
the tank.
• Use care in lling tank to avoid spilling fuel. Move
pressure washer away from fueling area before starting
engine.
• Heat will expand fuel in the tank, which could result in
spillage and possible re explosion.
• Fill tank to ½˝ (12.7 mm) below bottom of ller neck to
provide space for fuel expansion.
• Operating the pressure washer in an explosive
environment could result in a re.
• Operate and fuel equipment in well-ventilated areas
free from obstructions. Equip areas with re extinguisher
suitable for gasoline res.
• Materials placed against or near the pressure washer
can interfere with its proper ventilation features causing
overheating and possible ignition of the materials.
• Never operate pressure washer in an area containing dry
brush or weeds.
• Mufer exhaust heat can damage painted surfaces, melt
any material sensitive to heat (such as siding, plastic,
rubber, vinyl, or the pressure hose, itself), and damage
live plants.
• Always keep pressure washer a minimum of 4´ (1.2m)
away from surfaces (such as houses, automobiles or
live plants) that could be damaged from mufer exhaust
heat.
• Improperly stored fuel could lead to accidental ignition.
Fuel improperly secured could get into the hands of
children or other unqualied persons.
• Store fuel in an OSHA-approved container, in a secure
location away from work area.
• Use of acids, toxic or corrosive chemicals, poisons,
insecticides, or any kind of ammable solvent with this
product could result in serious injury or death.
• Do not spray ammable liquids.
DANGER
RISK OF EXPLOSION FOR FIRE
IMPORTANT SAFETY INSTRUCTIONS (CONT.)
• SAVE ALL INSTRUCTIONS
WHAT CAN HAPPEN HOW TO PREVENT IT
• Your pressure washer operates at uid pressures
and velocities high enough to penetrate human and
animal esh, which could result in amputation or other
serious injury. Leaks caused by loose ttings or worn
or damaged hoses can result in injection injuries. DO
NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a
physician immediately!
• Inspect the high-pressure hose regularly. Replace the
hose regularly. Replace the hose immediately if it is
damaged, worn, has melted from contacting the engine,
or shows any signs of cracking, bubbles, pinholes, or
other leakage. Never grasp a high-pressure hose that is
leaking or damaged.
• Never touch, grasp or attempt to cover a pinhole or
similar water leak on the high-pressure hose. The stream
of water IS under high pressure and WILL penetrate skin.
• Never place hands in front of nozzle.
• Direct spray away from self and others.
• Make sure hose and ttings are tightened and in good
condition. Never hold onto the hose or ttings during
operation.
• Do not allow hose to contact mufer.
• Never attach or remove wand or hose ttings while
system is pressurized.
• Injuries can result if system pressure is not reduced
before attempting maintenance or disassembly.
• To relieve system pressure, shut off engine, turn off water
supply and pull gun trigger until water stops owing.
• Use only hoses and accessories rated for pressure
higher than your pressure washer’s PSI.
DANGER
RISK OF FLUID INJECTION AND LACERATION
Copyright © 2017 MAT Industries, LLC
4 - ENG
IMPORTANT SAFETY INSTRUCTIONS (CONT.)
• SAVE ALL INSTRUCTIONS
WHAT CAN HAPPEN HOW TO PREVENT IT
• High-velocity uid spray can cause objects to break,
propelling particles at high speed.
• Light or unsecured objects can become hazardous
projectiles.
• Always wear ANSI-approved z87.1 safety glasses.
Wear protective clothing to protect against accidental
spraying.
• Never point wand at or spray people or animals.
• Always secure trigger lock when wand is not in service to
prevent accidental operation.
• Never permanently secure trigger in pull-back (open)
position.
DANGER
RISK OF INJURY FROM SPRAY
WHAT CAN HAPPEN HOW TO PREVENT IT
• Unsafe operation of your pressure washer could lead to
serious injury or death to you or others.
• Do not use chlorine bleach or any other corrosive
compound.
• Become familiar with the operation and controls of the
pressure washer.
• Keep operating area clear of all persons, pets and
obstacles.
• Do not operate the product when fatigued or under the
inuence of alcohol or drugs. Stay alert at all times.
• Never defect the safety features of this product.
• Do not operate machine with missing, broken or
unauthorized parts.
• Never leave wand unattached while unit is running.
• If proper starting procedure is not followed, engine can
kickback causing serious hand and arm injury.
• If engine does not start after two pulls, squeeze trigger
of gun to relieve pump pressure. Pull starter cord slowly
until resistance is felt. Then pull cord rapidly to avoid
kickback and prevent hand or arm injury.
• The spray gun/wand is a powerful cleaning tool that could
look like a toy to a child.
• Keep children away from the pressure washer at all
times.
• Reactive force of spray will cause gun/wand to kickback,
and could cause the operator to slip or fall or misdirect
the spray. Improper control of gun/wand can result in
injuries to self and others.
• Do not overreach or stand on an unstable support.
• Do not use pressure washer while standing on a ladder.
• Grip gun/wand rmly with both hands. Expect the gun to
kickback when triggered.
DANGER
RISK OF FLUID INJECTION AND LACERATION
WHAT CAN HAPPEN HOW TO PREVENT IT
• Breathing exhaust fumes will cause serious injury or
death! Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
• Operate pressure washer in a well-ventilated area. Avoid
enclosed areas such as garages, basements, etc.
• Never operate unit in a location occupied by humans or
animals.
• Some cleaning uids contain substances which could
cause injury to skin, eyes or lungs.
• Use only cleaning uids specically recommended
for high-pressure washers. Follow manufacturer's
recommendations. Do not use chlorine bleach or any
other corrosive compound.
DANGER
RISK TO BREATHING (ASPHYXIATION)
Copyright © 2017 MAT Industries, LLC
5 - ENG
WHAT CAN HAPPEN HOW TO PREVENT IT
• Fuel or oil leak or spill could result in re or breathing
hazard. Serious injury or death can result. Fuel or oil
leaks will damage carpet, paint or other surfaces in
vehicles or trailers.
• If pressure washer is equipped with a fuel shut-off valve,
turn the valve to OFF position before transporting to
avoid fuel leaks. If pressure washer is not equipped
with a fuel shut-off valve, drain the fuel from tank before
transporting. Only transport fuel in an OSHA-approved
container. Always place pressure washer on a protective
mat when transporting to protect against damage to
vehicle from leaks. Remove pressure washer from
vehicle immediately upon arrival at your destination.
RISK OF INJURY OR PROPERTY DAMAGE WHEN TRANSPORTING
OR STORING
DANGER
IMPORTANT SAFETY INSTRUCTIONS (CONT.)
• SAVE ALL INSTRUCTIONS
WHAT CAN HAPPEN HOW TO PREVENT IT
• Contact with hot surfaces, such as engine's exhaust
components, could result in serious burn.
• During operation, touch only the control surfaces of the
pressure washer. Keep children away from the pressure
washer at all times. They may not be able to recognize
the hazards of this product.
WARNING
RISK OF HOT SURFACES
WHAT CAN HAPPEN HOW TO PREVENT IT
• Use of acids, toxic or corrosive chemical, poisons,
insecticides, or any kind of ammable solvent with
this product could result in serious injury or death.
• Do not use acids, gasoline, kerosene, or any other ammable
materials in this product. Use only household detergents,
cleaners and degreasers recommended for use in pressure
washers.
• Wear protective clothing to protect eyes and skin from contact
with spraying materials.
WARNING
RISK OF CHEMICAL BURN
WHAT CAN HAPPEN HOW TO PREVENT IT
• Spray directed at electrical outlets or switches, or objects
connected to an electrical circuit, could result in a fatal
electric shock.
• Unplug any electrically operated product before
attempting to clean it. Direct spray away from electric
outlets and switches.
WARNING
RISK OF ELECTRICAL SHOCK
WHAT CAN HAPPEN HOW TO PREVENT IT
• Serious injury can result from attempting to lift too heavy
an object.
• The pressure washer is too heavy to be lifted by one
person. Obtain assistance from others before lifting.
WARNING
RISK OF INJURY FROM LIFTING
Copyright © 2017 MAT Industries, LLC
6 - ENG
SAFETY FEATURES
• SAVE ALL INSTRUCTIONS
THERMAL RELIEF VALVE
A thermal relief valve is provided to protect the
pump from overheating if the spray gun is
closed for an extended length of time or the
nozzle becomes plugged. However, it is
intended to be used as a backup system and
every effort should be made to not permit the
pump to heat up.
We recommend turning the pressure washer
off if it will not be used for more than five
minutes. This saves wear on the unit, reduces
fuel consumption and extends the life of the
pump by avoiding heat.
NOTICE
The pump will overheat and may
be damaged, or cause damage if allowed to
circulate more that five minutes.
SAFETY LOCK OFF LATCH
To prevent accidental discharge of high
pressure water, the safety latch on the trigger
should be engaged whenever the pressure
washer is not in use. (Refer to Operating
Instructions.)
LOW-OIL SHUTDOWN
The unit is equipped with a low oil sensor. If the
engine oil level becomes lower than required,
the pressure washer will automatically shut off.
(Refer to the engine manual for this feature.)
This protects your pressure washer engine from
operating without proper lubrication.
If the pressure washer engine shuts off and the
oil level is according to specification, check to
see if the pressure washer is sitting at an angle
that forces oil to shift. Place on an even
surface to correct this. If the engine fails to
start, the oil level may not be sufficient to
deactivate low oil level switch. Be sure the
engine is completely full of oil. See engine
manual.
SPARK ARRESTING MUFFLER
THIS PRODUCT MAY NOT BE EQUIPPED WITH
A SPARK ARRESTING MUFFLER. If the product
will be used around flammable materials, such
as agricultural crops, forests, brush, grass, or
other similar items, then an approved spark
arrester should be installed and is legally
required in the State of California. The California
statutes requiring a spark arrester are Sections
13005(b), 4442 and 4443. Spark Arresters are
also required on some U.S. Forest Service land
and may also be legally required under other
statutes and ordinances. For more information,
contact our Customer Service Department at
1-888-895-4549.
Maximum Pressure (PSI) ...................................................... 3100
Gallons Per Minute (GPM) .......................................................2.8
Maximum Inlet Pressure ...............................................Up to 90 PSIG
RPM ..................................................................3750 RPM
Temperature of Pumped Fluids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up to 80°F
Inlet Ports ........................................................... 3/4” GHT (F)
Discharge Ports ............................................................. M22
Your pressure washer has a maintenance-free pump. There is no need to change the pump oil.
SPECIFICATIONS
• SAVE ALL INSTRUCTIONS
Copyright © 2017 MAT Industries, LLC
7 - ENG
ASSEMBLY INSTRUCTIONS
• SAVE ALL INSTRUCTIONS
1. Place the unit on its back and insert wheel
axle into front tube (FIG 1). Use (1) M6
washer and (1) M6 x 15mm long hex head
screw to assemble wheel axle to frame
using the supplied open-end wrench.
Tighten securely. Repeat for opposite side.
2. Remove (1) M8 washer and (1) M8 nut from
wheel axle and place wheel onto axle
(FIG 2). Be sure the hub on the wheel goes
to the inside (FIG 3). The wheel hub side of
the wheel has the center piece that
protrudes out from the wheel approximately
a 1/4 inch. Re-assemble the washer and nut
onto axle using the supplied open-end
wrench (FIG 4). Tighten securely. Repeat for
opposite side.
3. With the unit still on its back, assemble the
rubber feet using (1) M8 x 25 mm long
socket head cap screw and (1) M8 nut
(FIG 5). Using the supplied hex wrench
and open-end wrench, tighten securely.
Repeat for opposite side (FIG 6).
4. Place the unit on its wheels and rubber feet.
Insert the handle into the frame (FIG 7).
Locate the handle hardware (bolts, washers
and knobs) in the plastic bag with the
Operation Manual. Ensure that the holes on
the handle and frame are aligned. Insert the
handle bolts through the holes from the
outside (FIG 8). Add the washer to the bolt,
then thread the knob onto the bolt from the
inside and securely tighten it into place
(FIG 8).
FIG 1
wheel axle
M6 washer
FIG 2
FIG 4FIG 3
wheel axle
wheel hub
M8 washer
FIG 6
FIG 5
M8 nut
M8 x 25 mm
head cap screw
M6 X 15mm
hex head
screw
M8 nut
FIG 8
FIG 7
knob
screw
handle
Copyright © 2017 MAT Industries, LLC
8 - ENG
ASSEMBLY INSTRUCTIONS (CONT.)
• SAVE ALL INSTRUCTIONS
5. Assemble the lower gun hook using
(1) M6 x 45mm long socket head cap screw,
(1) M6 nut, and the supplied hex wrench and
open-end wrench (FIG 9). Tighten securely
(FIG 10).
6. Assemble the upper gun hook using
(1) M6 x 45mm long socket head cap screw,
(1) M6 nut, and the supplied hex wrench and
open-end wrench (FIG 11). Tighten securely.
Assemble the wand by screwing together
the threaded connections of the two wand
halves. Hang the wand on the upper gun
hook, as shown in FIG 12.
7. Assemble the upper hose hanger using (2)
M6 x 45mm long socket head cap screws,
(2) M6 nuts, and the supplied hex wrench
and open-end wrench (FIG 13-16).
Tighten securely.
8. Final unit assembly (FIG 17).
9. A spark plug removal tool is included for
future maintenance (FIG 18). See provided
engine manual for spark plug maintenance
procedures.
FIG 10
FIG 12
FIG 9
FIG 11
upper gun hook
FIG 13
FIG 15 FIG 16
FIG 18
FIG 14
M6 X 45mm
head cap screw
M6 X 45mm
head cap screw
M6 nut
M6 nut
FIG 17
Copyright © 2017 MAT Industries, LLC
9 - ENG
SPRAY NOZZLE SELECTION
• SAVE ALL INSTRUCTIONS
Following is information concerning the five
nozzles provided with your pressure washer.
NOTE: The force of the spray on the
surface you are cleaning increases as
you move closer to the surface.
0° High Pressure (Red): The water stream
discharged is very aggressive. Use with
extreme caution to prevent damage to the
surface being cleaned or injury to persons
or animals.
15° High Pressure (Yellow): This is the
nozzle used for most cleaning applications. It
provides narrow coverage and a highly
powerful water stream.
25° High Pressure (Green): Use of this
nozzle offer both a medium coverage and
water stream. Best used for flushing dirt and
debris off surfaces.
40° High Pressure (White): This nozzle is
chemical injector to apply chemicals used for
cleaning with the widest coverage over a
larger area with a powerful water stream.
65° Low Pressure (Black): Provides low
pressure spray and a wide coverage. Used
primarily when operating the chemical injector
to apply chemicals.
BEFORE OPERATION
• SAVE ALL INSTRUCTIONS
NOTE: The engine and pump on your
EXCELL™ Pressure Washer will often have
improved performance after a break-in
period of several hours.
PRE-START PREPARATION
Before starting the pressure washer, check for
loose or missing parts and for any damage
which may have occurred during shipment.
HOSE AND GUN ASSEMBLY
NOTE: Align threaded connections care-
fully to prevent damaging threads during
assembly. Tighten connections securely
to prevent leaks during operation.
Attach the hose to the inlet of the trigger gun.
LUBRICATION
DO NOT attempt to start the pressure washer
engine without filling the engine crank case
with the proper amount and type of oil. (See
the accompanying engine manual for this
information.) Your pressure washer engine
has been shipped from the factory without oil
in the engine crankcase. Operating the unit
without oil will ruin the engine.
The pump is not equipped with a dipstick or sight
glass windows. Check oil leaks from the pump.
Pump oil is shipped in the pump from factory.
FUEL
Fill the tank with clean, fresh unleaded
automotive gasoline. (See Figure 1). Regular
grade gasoline may be used provided a high
octane rating is obtained (at least 85 pump
octane).
WARNING
Gasoline is very dangerous.
Serious injury may result from fire caused
by gasoline contacting hot surfaces.
Do not overfill the tank. Keep maximum
fuel level 1/2 inch below the bottom of the
filler neck. This will allow expansion in
hot weather and prevent overflow.
Copyright © 2017 MAT Industries, LLC
10 - ENG
ENGINE AND PUMP FEATURES - FIGURE 1
• SAVE ALL INSTRUCTIONS
OPERATING CONNECTIONS
• SAVE ALL INSTRUCTIONS
HIGH PRESSURE HOSE
Attach the high pressure hose to the outlet
connection located on the pump. (See Figure 1).
WATER CONNECTION
Before connecting to unit, run water through
the garden hose (not supplied) to flush out any
foreign matter. Check that the screen is clean
and is in the inlet of the pump. Attach garden
hose to the inlet connection located on the
pump. (See Figure 1).
NOTE: The water supply must provide a
minimum of 4 GPM at 40 to 80 PSI or the
pump will be damaged.
FUEL FILL
SIPHON
INJECTOR
THERMAL
RELIEF VALVE
OUTLET
CONNECTION
THROTTLE
LEVER
INLET
CONNECTION
AIR FILTER
CHOKE LEVER
FUEL ON/OFF
RECOIL
STARTER
OIL FILL
OIL DRAIN
ENGINE
ON/OFF
SWITCH
Copyright © 2017 MAT Industries, LLC
11 - ENG
OPERATING INSTRUCTIONS
• SAVE ALL INSTRUCTIONS
START-UP PROCEDURE
1. Ensure water supply is connected and
turned on.
2. Release gun safety lock.
3. To allow air to escape from the hose, squeeze
trigger on the gun until there is a steady
stream of water coming from the nozzle.
4. Remove any dirt or foreign matter from the
gun outlet and the male connector of the wand.
5. Insert the nozzle wand into the gun wand
and tighten the twistfast fitting securely by
hand.
NOTICE
There is a shipping plug
inserted in the oil breather when pump is
shipped from the factory. The shipping
plug prevents any oil from leaking out of
the pump during shipping. The shipping
plug must be removed before the
pressure washer is operated. To remove
the shipping plug, pull it out directly.
The pump is supplied with the correct
amount of oil and does not require further
service.
STARTING THE ENGINE
(See Figure 1, page 10)
1. Check engine oil and fuel levels
2. Move the fuel lever to the “ON” position.
3. Adjust the choke lever as necessary (full
choke “ON” for a cold engine, half choke or
no choke may be needed for a warm
engine - recently run).
4. Adjust the throttle lever as necessary (half
throttle is recommended for starting).
5. Turn the engine on/off switch to the “ON”
position.
6. Squeeze and hold the trigger on the high
pressure gun to release the pressure on the
pump. Failure to do this will make the unit
hard to start.
7. While still holding the trigger on the high
pressure gun, pull the engine starter rope
with a fast steady pull until engine starts.
8. As the engine warms up, move choke lever
to off position.
WARNING
If the wand or nozzle is
not securely locked into place, it could
be ejected under high pressure when
operating the gun, possibly causing injury
or damage.
CHEMICAL INJECTION
• SAVE ALL INSTRUCTIONS
1. Attach injection tube assembly to the siphon
injector on the pump (see Figure 1, page 10).
2. Open a container of pressure washer
chemical and place next to the unit near the
injection tube.
3. Visually inspect strainer at the end of the
injection tube to verify that it is not clogged.
4. Insert the injection tube into the container all
the way to the bottom.
5. Remove the high-pressure nozzle from the
wand and install the black injection nozzle.
The solution will automatically be mixed with
the water and discharged through the nozzle.
NOTICE
This pressure washer is
intended for use only with liquid car wash
detergents, developed specically for
pressure washer and with mild soaps.
Only use chemicals compatible with the
aluminum and brass parts of the pressure
washer. Powdered soaps may clog the
injection system. Always use chemicals
according to manufacturer directions. MAT
Industries, LLC assumes no responsibility
for any damages caused by chemicals
injected through this pressure washer.
Copyright © 2017 MAT Industries, LLC
12 - ENG
CLEANING TECHNIQUES
• SAVE ALL INSTRUCTIONS
When cleaning with the pressure washer,
many cleaning tasks can be solved with water
alone, but for most tasks it is advantageous to
use a detergent also. A detergent ensures a
quick soaking of the dirt allowing the high
pressure water to penetrate and remove the
dirt more effectively.
Pressure washer chemicals are specially for-
mulated to be used with your pressure washer.
APPLICATION OF SOAP OR
DEGREASER
1. Apply the solution to a DRY work surface.
On a vertical surface, apply horizontally
from side to side starting from the bottom
to avoid streaking.
NOTE: Wetting the surface first is not
recommended, as it dilutes the
detergent and reduces its cleaning
ability. Avoid working on hot surfaces
or in direct sunlight to minimize the
chances of the chemical damaging
painted surfaces. Damage may occur
to painted surface if chemical is
allowed to dry on the surface. Hold
nozzle far enough away from surface
to prevent damage to the surface.
2. Allow chemical to remain on the surface
for a short time before rinsing.
3. Rinse with clean water under high pressure.
On a vertical surface, first rinse from the
bottom up, then rinse from the top down.
Hold nozzle 6 to 8 inches from the work
surface at a 45° angle using the flat spray
as a peeling tool rather than a scrub brush.
APPLICATION OF WAX
1. Immediately after cleaning, apply pressure
washer wax. Place injection tube in
container of wax.
2. Apply the wax sparingly in an even layer.
Apply to wet surfaces from the bottom up
for even distribution and to avoid streaking.
3. Remove the suction tube from the wax
bottle and rinse off the surplus wax.
NOTE: IF SURPLUS WAX IS NOT
REMOVED, A HAZY FINISH MAY RESULT.
4. Wipe dry to reduce water spotting.
END OF CLEANING OPERATION
• SAVE ALL INSTRUCTIONS
When you have completed use of the chemical
injection system, remove tube from container.
Continue to run in low pressure position and
inject clean water through the tube and
injection system by placing end of tube in a
container of clean water. Continue to run until it
is thoroughly cleaned.
Copyright © 2017 MAT Industries, LLC
13 - ENG
MAINTENANCE
• SAVE ALL INSTRUCTIONS
CONNECTIONS
Connections on pressure washer hoses, gun
and spray wand should be cleaned regularly
and lubricated with silicon grease to prevent
leakage and damage to the o-rings.
NOZZLE
Clogging of the nozzle causes the pump
pressure to be too high and cleaning is
immediately required.
WARNING
A nozzle cleaner must
only be used when the spray nozzle is
disconnected from the gun or personal
injury could result.
1. Remove the nozzle from the wand.
2. Clear the nozzle with the nozzle cleaner
pin provided with the pressure washer.
3. Flush the nozzle backwards with water.
4. Re-install the nozzle into the wand.
Restart the pressure washer and depress the
trigger on the spray gun. If the nozzle is still
plugged or partially plugged, repeat above
items 1-4.
If the previous procedure does not clear the
nozzle, replace with a new nozzle.
WATER SCREEN
The pressure washer is equipped with a water
inlet screen to protect the pump. If the screen
is not kept clean, it will restrict the flow of
water to the pressure washer and may cause
damage to the pump. Do not damage the
screen while removing or cleaning screen.
Any foreign particles entering the pump may
damage the pump. Do not operate pressure
washer without the screen in place.
Remove the screen and back flush to remove
impurities from screen. Replace immediately.
ENGINE MAINTENANCE
During the winter months, rare atmospheric
conditions may develop which will cause an
icing condition in the carburetor. If this
develops, the engine may run rough, lose
power, and may stall.
NOTE: Refer to the engine manufacturer’s
manual for service and maintenance of
the engine.
Copyright © 2017 MAT Industries, LLC
14 - ENG
STORAGE
• SAVE ALL INSTRUCTIONS
PUMP STORAGE
If you must store your pressure washer in a
location where the temperature is below 32°F,
you can minimize the chance of damage to
your machine by utilizing the following
procedure:
1. Shut off water supply and relieve pressure
in the spray gun by depressing the trigger.
Disconnect the garden hose from the
pressure washer, but leave the high-
pressure hose connected.
2. Tip the unit on its side with the inlet
connection pointing up.
3. Insert a small funnel (to prevent spilling)
into the inlet and pour in approximately 1/4
cup of RV antifreeze.
4. Disconnect spark plug wire.
5. Without connecting garden hose pull the
recoil several times to circulate the anti
freeze in the pump system. Continue to
add antifreeze and pull the recoil until the
antifreeze is expelled when the trigger is
pulled.
6. Turn the unit upright.
NOTICE
Prior to restarting, thaw out
any possible ice from the pressure wash-
er hoses, spray gun and wand.
Another method of reducing risks of freeze dam-
age is to drain your pressure washer as follow:
1. Stop the pressure washer and detach supply
hose and high pressure hose. Squeeze
the trigger of the discharge gun to drain all
water from the wand and hose.
2. Restart the pressure washer and let it run
briefly (about 5 seconds) until water no longer
discharges from the high pressure outlet.
ENGINE STORAGE
When the pressure washer is not being
operated or is being stored more than one
month, follow these instructions:
1. Replenish engine oil to upper level.
2. Drain gasoline from fuel tank, fuel line, fuel
valve and carburetor.
3. Pour about one teaspoon of engine oil
through the spark plug hole, pull the recoil
starter several times and replace the plug.
Then pull the starter slowly until you feel
increased pressure which indicates the
piston is on its compression stroke and
leave it in that position. This closes both
the intake and exhaust valves to prevent
the inside of the cylinder from rusting.
4. Cover the pressure washer and store in a
clean, dry place that is well ventilated away
from open flame or sparks.
NOTE: We recommend always using a
fuel stabilizer. A fuel stabilizer will
minimize the formulation of fuel gum
deposits during storage. The fuel
stabilizer can be added to the gasoline in
the fuel tank, or into the gasoline in a
storage container.
Copyright © 2017 MAT Industries, LLC
15 - ENG
LIMITED WARRANTY
• SAVE ALL INSTRUCTIONS
Always specify model number when contacting the manufacturer.
We reserve the right to amend these specications at any time without notice. The only warranty applicable
is our standard written warranty. We make no other warranty, expressed or implied. MAT Industries, LLC
warrants this pressure washer and any parts thereof, to be free from defects in material and workmanship
for two (2) years (90 days for commercial use or for reconditioned unit) from the date of rst purchase from
an authorized dealer, provided that the product has been properly maintained and operated in accordance
with all applicable instructions. This warranty is extended to the original retail purchaser. The bill of sale or
proof of purchase must be presented at the time a claim is made under this warranty. This warranty does
not cover industrial or rental usage, nor does it apply to parts that are not in original condition because of
normal wear and tear, or parts that fail or become damaged as a result of misuse, accident, lack of proper
maintenance, tampering, or alteration. Exceptions to this standard warranty period would be normal wear
items such as air lters and spark plugs which are covered for sixty (60) days against defects in material
and workmanship. Travel, handling, transportation, and incidental costs associated with warranty repairs
are not reimbursable under this warranty and are the responsibility of the owner. To the full extent allowed
by the law of the jurisdiction that governs the sale of the product, this express warranty excludes any and
all other expressed warranties and limits the duration of any and all implied warranties, including warranties
of merchantability and tness for a particular purpose to two (2) years from the date of rst purchase, and
MAT Industries, LLC’s liability is hereby limited to the purchase price of the product and MAT Industries, LLC
shall not be liable for any other damages whatsoever including direct, incidental, or consequential damages.
Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation
of incidental or consequential damages, so the above limitation of damages may not apply to you. This
warranty provides the original purchaser with specic rights.
For information regarding those rights, please consult the applicable state laws.
MAT Industries, LLC Corporate Ofce – CORRESPONDENCE ONLY
ATTN: Technical Services – MIND
6700 Wildlife Way
Long Grove, IL
60047
The Engine Emissions Control System Warranty is provided by the engine manufacturer, included with this
product and administered by MAT Industries, LLC.
Copyright © 2017 MAT Industries, LLC
16 - ENG
TROUBLESHOOTING GUIDE
• SAVE ALL INSTRUCTIONS
Problem Cause Correction
Engine will not start or
stops while operating
1. Low-oil shutdown.
2. Engine switch not in the “ON” position.
3. Pressure build up in pump/hose.
1. Ensure engine oil is at proper level
2. Turn switch to "ON" position
3. Squeeze and hold gun trigger while starting
(see STARTING THE ENGINE on page 11).
Engine is overloaded 1. Nozzle partially blocked. 1. Clean nozzle.
Water or oil leaking
from bottom of pump
1. A small amount of leakage is normal. 1. If excessive leaking occurs call the Customer
Service Department.
Pressure increases
when gun is closed
1. Bypass valve not operating properly. 1. Call the Customer Service Department.
Engine running but
pump not building
maximum pressure or
has irregular pressure
1. Faucet closed.
2. Unit has been stored in freezing
temperatures.
3. Inadequate water supply.
4. Water inlet screen clogged.
5. Kink in garden hose.
6. Wand nozzle worn or damaged.
7. Air in pump.
8. Suction or discharge valves clogged or
worn out.
9. By-pass valve not operating effectively.
1. Open faucet.
2. Thaw out unit completely including hose, gun
and wand.
3. Provide a minimum of 4 gpm at 20 psi.
4. Clean screen.
5. Straighten hose.
6. Replace nozzle.
7. Let run with gun open and wand removed
until steady stream of water is released.
8. Call the Customer Service Department.
9. Call the Customer Service Department.
No intake of chemicals
1. Injection tube not securely inserted into
unit.
2. Tube cracked or split.
3. Wrong nozzle.
4. Injection tube strainer clogged.
5. Nozzle blocked.
6. Dried chemicals in injector.
1. Push firmly into injector.
2. Replace tubing.
3. Switch to low pressure nozzle.
4. Clean strainer.
5. Clean nozzle.
6. Dissolve by running warm water trough the
injection tube.
Trigger will not move 1. Gun safety lock engaged. 1. Release safety lock.
Water in crankcase 1. High humidity.
2. Worn seals.
1. Change oil more frequently.
2. Call the Customer Service Department.
Noisy operation 1. Worn bearings
2. Air mixed with water.
1. Call the Customer Service Department.
2. Check inlet lines for restrictions and /or proper
sizing.
Rough/pulsating
operation with
pressure drop
1. Worn packing.
2. Inlet restriction.
3. Unloader.
4. Air mixed in water.
1. Call the Customer Service Department.
2. Check system for stoppage, air leaks.
correctly sized inlet plumbing to pump.
3. Check unloader for proper operation.
4. Check inlet lines for restrictions and/or proper
sizing.
High crankcase
temperatures
1. Wrong grade of oil.
2. Improper amount of oil in crankcase.
1. Use recommended oil.
2. Adjust oil level to proper amount.
LAVEUSE À PRESSION
GUIDE D’UTILISATION
pour modèle EPW2123100
Inscrivez tous les renseignements
et agrafez le reçu de caisse ici pour
références futures :
Date d’achat :__________________________
N° de série : ________________________________
Questions? 1-888-895-4549
Référez au site Web pour le manuel
électronique et la liste des pièces.
www.powermate.com
IMPORTANT: Assurez-vous que toute personne qui utilisera cet équipement lise attentivement
ces instructions avant de l’utiliser.
N° de pièce E110166// Rev. 2
06/26/2018 IMPRIMÉ EN CHINE
TABLE DES MATIÈRES
Mesures de sécurité/Dénitions .................... 18
Renseignements sur la sécurité
du consommateur ......................................... 18
Mesures de sécurité importantes ................. 18
Mesures de sécurité ...................................... 22
Spécications ................................................ 22
Directives d’assemblage ............................... 23
Choix de buse de pulvérisation ..................... 25
Avant toute utilisation .................................... 25
Caracteristiques de moteur et pompe 26
Raccordements ............................................. 26
Utilisation ....................................................... 27
Procédure de lancement ............................... 27
Utilisation de produits chimiques .................. 27
Technique de nettoyage ................................ 28
Fin de l'activité de nettoyage ......................... 28
Entretien ........................................................ 29
Rangement .................................................... 30
Garantie ......................................................... 31
Guide de dépannage ..................................... 32
English ............................................................. 1
Español .......................................................... 33
Copyright © 2017 MAT Industries, LLC
18 - FR
MESURES DE SÉCURITÉ – DÉFINITIONS
• CONSERVER TOUTES LES INSTRUCTIONS
Ce guide contient des renseignements importants que vous deviez bien saisir. Cette information porte sur
VOTRE SÉCURITÉ et sur LA PRÉVENTION DE PROBLÈMES D’ÉQUIPEMENT. A n de vous aider à identi er
cette information, nous avons utilize les symboles ci-dessous. Veuillez lire attentivement ce guide en portant
une attention particulière à ces symboles.
DANGER
Indique un danger imminent
qui, s’il n’est pas évité, CAUSERA DE GRAVES
BLESSURES OU LA MORT.
ATTENTION
Indique la possibilité d’un
danger qui, s’il n’est pas évité, PEUT causer DES
BLESSURES MINEURES OU MOYENNES.
AVERTISSEMENT
Indique la possibilité
d’un danger qui, s’il n’est pas évité, POURRAIT
CAUSER DE GRAVES BLESSURES OU LA MORT.
AVIS
Sans le symbole d’alerte. Indique la pos-
sibilité d’un danger qui, s’il n’est pas évité, PEUT
causer DES DOMMAGES À LA PROPRIÉTÉ.
RENSEIGNEMENTS SUR LA SÉCURITÉ DU CONSOMMATEUR
• CONSERVER TOUTES LES INSTRUCTIONS
AVERTISSEMENT
Il se peut que ce produit ne soit pas équipé d’un silencieux à pare-étincelles.
Si le produit n’en est pas équipé, et s’il est utilisé près de matériaux inammables ou sur de la terre
couverte de produits agricoles, forêts, broussailles, gazon ou autres articles semblables, un pare-étincelles
approuvé doit être posé, et est exigé par la loi en Californie. Selon la section 13005(b) de la loi de la
Californie, et les sections 4442 et 4443 du Code sur les ressources publiques de la Californie, ce produit
ne peut pas être utilisé en Californie, à moins que le moteur ne soit équipé d’un pare-étincelles, tel que
décrit dans la section 4442, et à moins que l’appareil ne soit maintenu en bon état de fonctionnement. Des
pare-étincelles sont également requis sur certaines terres forestières des États-Unis et peuvent être exigés
légalement sous certains autres lois et arrêtés.
AVERTISSEMENT : CONTIENT DU PLOMB. PEUT ÊTRE NOCIF S'IL EST INGÉRÉ OU MÂCHÉ. PEUT
GÉNÉRER DE LA POUSSIÈRE CONTENANT DU PLOMB. SE LAVER LES MAINS APRÈS USAGE. GARDER
HORS DE LA PORTÉE DES ENFANTS.
AVERTISSEMENT : CE PRODUIT POURRAIT VOUS EXPOSER À DES PRODUITS CHIMIQUES,
Y COMPRIS LE PLOMB, RECONNU PAR L’ÉTAT DE CALIFORNIE COMME CAUSE DE CANCER, DE
MALFORMATIONS CONGÉNITALES OU AUTRES PROBLÈMES DU SYSTÈME DE REPRODUCTION. POUR
OBTENIR PLUS D’INFORMATION, VISITEZ WWW.P65WARNINGS.CA.GOV.
MESURES DE SÉCURITÉ IMPORTANTES
• CONSERVER TOUTES LES INSTRUCTIONS
AVERTISSEMENT
N’utilisez pas cet appareil avant d’avoir lu et compris les instructions sur la
sécurité, l’utilisation et l’entretien de ce Guide de l’utilisateur et du Guide du propriétaire du moteur.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
Copyright © 2017 MAT Industries, LLC
19 - FR
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Les cigarettes, étincelles, arc électrique, gaz
d’échappement et des parties chaudes du moteur telles
qu’un silencieux peuvent enammer l’essence déversée
et ses vapeurs.
• Éteindre le moteur et le laisser refroidir avant de remplir
le réservoir d’essence.
• Être attentif et éviter de déverser de l’essence lors du
remplissage du réservoir. Éloigner la laveuse haute
pression de la zone de ravitaillement avant de démarrer
le moteur.
• Le combustible du réservoir se dilate sous l’effet de la
chaleur et pourrait se solder par un déversement et un
incendie ou une explosion.
• Laisser environ 127 mm (1/2 po) de dégagement sous
le bord du goulot de remplissage pour permettre
l’expansion de l’essence.
• Le fonctionnement de la laveuse haute pression dans un
milieu explosif pourrait se solder par un incendie.
• Utiliser et faire le plein d’essence de l’équipement dans
des zones bien dégagées de tout obstacle. Installer
un extincteur adéquat dans les zones de travail pour
combattre les incendies à base d’essence.
• Du matériel déposé contre ou près de la laveuse
haute pression peut interférer avec les fonctionnalités
d’aération de l’équipement et provoquer une surchauffe
et l’allumage du materiel (risque d’incendie).
• Ne jamais utiliser la laveuse haute pression dans une
zone avec arbustes ou broussailles secs.
• La chaleur de l’échappement du silencieux peut
endommager des surfaces peintes, faire fondre tout type
de matériel sensible à la chaleur (comme du revêtement
extérieur, plastique, caoutchouc, vinyle ou meme le
tuyau haute pression) et nuire aux plantes vivantes.
• Toujours éloigner la laveuse haute pression d’au moins
1,2 m (4 pi) de toutes surfaces (telles que desmaisons,
voitures, ou des plantes vivantes) qui pourraient
être endommagées par la chaleur s’échappant du
silencieux.
• De l’essence mal entreposée pourrait provoquer un
allumage (incendie) accidentel. Ranger l’essence de
façon sécuritaire pour en empêcher l’accès aux enfants
et à toutes autres personnes non qualiées.
• Entreposer l’essence dans un contenant homologué
par la Loi sur la santé et la sécurité du travail dans un
emplacement sécuritaire loin de la zone de travail.
• L’utilisation d’acides, de produits chimiques toxiques ou
corrosifs, de poisons, d’insecticides ou de toute sorte de
solvant inammable dans ce produit pourrait provoquer
des blessures graves ou la mort.
• Ne pas vaporiser des liquids inammables.
DANGER
RISQUE D’EXPLOSION OU D’INCENDIE
MESURES DE SÉCURITÉ IMPORTANTES (SUITE)
• CONSERVER TOUTES LES INSTRUCTIONS
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Votre laveuse haute pression fonctionne à
des pressions de liquides et des vitesses
sufsamment élevées pour pénétrer
la peau de l’homme et animale, ce qui
pourrait se solder par une amputation
ou autre blessure grave. Des fuites
provoquées par des raccords lâches ou
des tuyaux usés ou endommagés peuvent
se solder par des blessures par injection.
NE PAS TRAITER UN INJECTION DE
LIQUIDE COMME UNE SIMPLE COUPURE
! Consulter un médecin immédiatement !
• Inspecter périodiquement le tuyau haute pression. Remplacer
immédiatement le tuyau s’il est endommagé, usé, s’il a fondu en
contact avec le moteur ou s’il démontre un signe de ssure, des bulles,
des trous d’épingle ou tout autre fuite. Ne jamais saisir untuyau haute
pression quifuit ou est endommagé.
• Ne jamais toucher, saisir ou essayer de couvrir un trou minuscule ou
tout autre fuite similaire sur le tuyau haute pression.
• Le jet d’eau EST sous haute pression et PÉNÈTRERA la peau.
• Ne jamais mettre les mains devantl’embouchure.
• Éloigner le jet, ne pas le diriger vers soimême ou autrui.
S’assurer que le tuyau et les raccords sont serrés et en bon état. Ne
jamais s’agripper au tuyau ou aux raccords en cours de fonctionnement.
• Ne pas mettre le tuyau en contact avec le silencieux.
• Ne jamais attacher ou retirer le tube ou les raccords du tuyau avec le
système sous pression.
• Il y a risque de blessures si la pression
n’est pas réduite avant d’essayer de
procéder à un entretien ou un démontage.
• Pour décompresser le système, éteindre le moteur, fermer
l’approvisionnement en eau et enclencher la détente du pistolet jusqu’à
l’arrêt complet de l’écoulement d’eau.
• Utiliser uniquement des tuyaux et accessoires classés pour des
pressions plus élevées que le PSI de la laveuse haute pression.
DANGER
RISQUE D’INJECTION ET DE LACÉRATION
Copyright © 2017 MAT Industries, LLC
20 - FR
MESURES DE SÉCURITÉ IMPORTANTES (SUITE)
• CONSERVER TOUTES LES INSTRUCTIONS
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Un jet de liquide à haute vitesse
peut briser des objets et projeter
les éclats à haute vitesse.
• Des objets légers ou mal xés peu-
vent se transformer en projectiles
dangereux.
• Toujours porter des lunettes de sécurité conformes à la norme ANSI Z87.1
Porter des vêtements protecteurs pour se protéger de jets accidentels.
• Ne jamais diriger la lance ou le jet vers une personne ou des animaux.
• Toujours xer solidement le verrou de la détentelorsque le tube pulvérisateur
est inutilisé pour empêcher tout fonctionnement accidentel.
• Ne jamais xer, de façon permanente, la détente en position arrière (ouverte).
DANGER
RISQUE DE BLESSURE PAR JET
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Une utilisation dangereuse de la
laveuse haute pression pourrait
provoquer de graves blessures, voire
son proper décès ou celle d’autres
personnes.
• Ne pas utiliser de produit à blanchir au chloreou tout autre composé corrosif.
• Se familiariser ave le fonctionnement et les commandes de la laveuse haute
pression.
• Tenir la zone de travail exempte de toutes personnes, animaux et obstacles.
• Ne pas utiliser le produit en cas de fatigue ou sous l’emprise d’alcool ou de
drogues. Rester vigilant en tout temps.
• Ne jamais rendre inopérant les caractéristiques de sécurité du produit.
• Ne pas utiliser l’appareil avec des pieces manquantes, brisées ou non
autorisées.
• Ne jamais laisser le tube pulvérisateur sans surveillance lors du
fonctionnement de l’appareil.
• Suivre la procédure de démarrage
correcte pour éviter l’effet de rebond
moteur qui provoquerait ainsi une
blessure grave à la main ou au bras.
• Si le moteur ne démarre pas après deux tentatives, appuyer sur la détente
du pistolet pour décompresser la pompe. Tirer délicatement la corde du
démarreur jusqu’à obtention d’une résistance. Puis tirer rapidement sur
celui-ci pour éviter l’effet de rebond moteur et empêcher toute blessure à la
main ou au bras.
• Le pistolet et le tube de pulvérisation
sont des outils de nettoyage
puissants qui ressemblent à un jouet
pour un enfant.
* Garder la laveuse haute pression hors de portée des enfants en tout temps.
• Le pistolet et le tube de pulverization
réagissent à la pression du jet et
provoqueront un effet de rebond
qui pourrait faire glisser, ou tomber,
l’opérateur ou rediriger le jet. Une
maîtrise imparfaite du pistolet et
de la lance peut provoquer des
blessures à soi même et à autrui.
• Ne pas trop tendre les bras ou se tenir debout sur une surface instable.
• Ne pas utiliser une laveuse haute pression debout sur une échelle.
• Saisir solidement à deux mains le pistolet/tube de pulvérisation.
S’attendre à un effet de rebond lors de l’enclenchement de la détente.
DANGER
RISQUE D’UTILISATION DANGEREUSE
CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER
• Respirer les vapeurs d’échappement provoquera
de graves blessures voire, un décès ! Les gaz
d’échappement des moteurs contiennent du monoxyde
de carbone, un gaz inodore et mortel.
• Utiliser la laveuse haute pression dans une zone bien
aérée. Éviter les endroits clos comme les garages, les
sous-sols, etc.
• Ne jamais utiliser l’appareil dans un endroit habité par
des hommes ou des an maux.
• Certains liquides nettoyants contiennent des substances
pouvant provoquer des blessures à la peau, aux yeux ou
au système respiratoire.
• Utiliser uniquement des liquids nettoyants spécialement
recommandés pour les laveuses haute pression. Suivre
les recommandations des fabricants.Ne pas utiliser
de produit à blanchir au chlore ou tout autre composé
corrosif.
DANGER
RISQUE D’ASPHYXIE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Excell EPW2123100 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur

dans d''autres langues