Oreck UK30300 Mode d'emploi

Important:

Read carefully before assembly and use.

user

MANUA L

upright vacuums

UK30200/UK30200 #964A00085 ID116502-R0

Only Elevate Conquer

™

Model is pictured here.

2

THANK YOU

for purchasing an Oreck

®

product.

Please register your product to initiate warranty, service

plans and expert advice on whole-home cleaning:

online at oreck.com or call 1.800.989.3535(U.S) or

1.888.676.7325 (Canada) to register by phone.

3

Table of Contents

Important Safety Instructions 6

Vacuum Introduction 8

Technical Specications 9

Operation 10

Assembling your Elevate

™

10

Using Your Elevate

™

12

Maintenance 14

Changing the Filtration Bag 14

Adjusting or Replacing Brushroll 16

Clearing Blockages 18

Troubleshooting 20

Service 21

Warranty 22

Spanish 23

French 45

4

Only certied Oreck

®

Accessories, parts and ltration bags can be used with this vacuum. Oreck

®

cannot guarantee optimal performance with

the use of unauthorized products, thus the use of non-Oreck

®

components will void warranty.

To ensure accessories, parts and ltration bags are genuine, purchase only through a Factory Authorized Dealer or through oreck.com.

Certied Oreck

®

ltration bags will carry the mark below.

Certiﬁed Parts

5

6

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND

USE. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. IF

USED COMMERCIALLY OR WITH NON-ORECK

®

FILTRATION BAGS

AND COMPONENTS, WARRANTY IS VOID.

When using an electrical appliance, basic precautions should always be

followed, including the following: READ ALL INSTRUCTIONS

BEFORE USING THIS APPLIANCE.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR INJURY:

• Fully assemble before operating.

• Operate vacuum only at voltage speciﬁed on data plate on bottom of cleaner.

• Do not leave vacuum when plugged in. Unplug from outlet when not in use and

before cleaning or servicing.

• Do not use outdoors or on wet surfaces.

• Do not allow to be used as a toy. Not intended for use by children age 12 and under.

Close supervision is necessary when used near children. To avoid injury or damage,

keep children away from product, and do not allow children to place ﬁngers or other

objects into any openings.

• Use only as described in this manual. Use only manufacturer’s recommended

attachments and products.

• Do not use with damaged power cord or plug. If vacuum is not working as it should,

has been dropped, damaged, left outdoors, or dropped into water, have the product

inspected by an Authorized Oreck

®

Service Center prior to continuing use. Call

1-800-989-3535 for the nearest service center or visit our website at

www.oreck.com.

• Do not pull or carry by power cord, use cord as handle, close a door on cord, or pull

cord around sharp edges or corners. Do not run vacuum over cord. Keep cord away

from heated surfaces.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not handle plug or vacuum with wet hands.

• Do not put any objects into openings. Do not use with any opening blocked; keep

free of dust, lint, hair, and anything that may reduce air ﬂow.

• Keep hair, loose clothing, ﬁngers, and all parts of body away from openings and

moving parts. Brushroll continues to operate when in the upright position.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs. Do not place vacuum on stairs or furniture,

as it may result in injury or damage.

• Do not use to pick up ﬂammable or combustible liquids, such as gasoline, or ﬁne

wood sandings or use in areas where they may be present.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches,

or hot ashes.

SAFETY INSTRUCTIONS

7

• Do not use without inner ﬁltration bag in place.

WARNING: This product contains chemicals, known to the State

of California to cause cancer and birth defects or other reproductive harm.

WASH HANDS AFTER USING.

CAUTION: TO REDUCE THE RISK OF

DAMAGE:

• Avoid picking up hard, sharp objects with this product, as they may cause damage.

• Store appropriately indoors in a dry place. Do not expose machine to freezing

temperatures.

• Brushroll continues to rotate while product is turned on and handle is in the upright

position. To avoid damage to carpet, rugs and ﬂooring, avoid tipping vacuum or

setting it on furniture, fringed area rugs or carpeted stairs.

• With brushroll on, do not allow cleaner to sit in one location for an extended period

of time, as damage to ﬂoor can result.

WARNING: To reduce the risk of electric shock, this vacuum

has a polarized plug (one blade is wider than the other). This plug will t in

a polarized outlet only one way. If the plug does not t fully in the outlet,

reverse the plug. If it still does not t, contact a qualied electrician to

install the proper outlet. Do not change the plug in any way.

Any other servicing should be done by an authorized service

representative. Call 1-800-989-3535 for the nearest service center or

visit our website at www.oreck.com.

8

Vacuum Introduction

A

Ergonomic Handle

B

On/Off Fingertip Controls

C

Power Cord Release Hook

D

Upper Tube

E

Filtration Bag Port

F

Filtration Bag

G

Carry Handle

H

Security Zipper

I

Power Head

J

Protective Bumper

K

Side Edge Brushes

L

Service Door

M

LED Headlights

N

Filtration Bag

O

Power Cord

P

Connectivity Cord

Q

Upper Tube Connector

R

Debris Transfer Tube

S

Filtration Bag Case

T

Lower Tube Connectors

U

Lower Tube

V

Fan Housing

W

Case Clasp

X

Brushroll

Y

Front and Rear Wheels

Z

Debris Shield

Z1

Power Head Nozzle

9

VACUUM INTRODUCTION

Technical Speciﬁcations

Name Voltage Current Wattage Cord Length Weight

UK30200 120V 3.5A 480W 35 ft 10 lbs

UK30300 120V 3.5A 480W 35 ft 10 lbs

A

B

E

H

Z

J

U

K

G

O

P

N

C

L

X

Q

V

T

S

D

F

R

I

W

M

Y

10

Operation — Assembling your Elevate

™

1

Make sure Upper Tube Connector (A) is installed

on Upper Tube (B). 2

Insert Upper Tube into the top of Debris Transfer Tube (C)

until it locks in place.

A

C

B

11

OPERATION— ASSEMBLING YOUR ELEVATE

™

3

Twist Upper Tube Connector (A) clockwise until it clicks to

secure Upper Tube (B).

A

B

12

2

Push ngertip controls on the handle

forward to select Hard Floor or Carpet

mode. Push controls backward into

the “OFF” position to turn off. If using

on frieze or very high pile carpet, use

on Hard Floor mode.

Operation — Using Your Elevate

™

1

Make sure the ltration bag (A) is attached

properly to the ltration bag dock (B).

Attachment instructions are located on the

ltration bag and in the maintenance section

of this manual. Your vacuum comes with a

bag preinstalled for your convenience. Do not

operate without a bag.

3

Step on the (A) power head and pull handle

back to lower into operating position. Return

handle to full upright position to engage

lock. Do not operate vacuum while in the

upright and locked position.

Please read “Important Safety Instructions” before use.

CAUTION NOT TO BE USED FOR GROOMING A PET.

A

B

A

13

OPERATION — USING YOUR ELEVATE

™

4

Wrap Power Cord around Power Cord Release

Hook (A) and the Carry Handle (B) as shown for

convenient storage. Use the clip on the plug (C)

to attach the plug end to the power cord. Raise

the carry handle for easy lifting and carrying.

Lower the carry handle during other use to

eliminate obstructions.

5

Twist the power cord release hook to either side

to quickly unwrap the power cord for use.

A

C

B

14

WARNING TO REDUCE THE RISK OF PERSONAL INJURY,

UNPLUG BEFORE CLEANING OR SERVICING. DO NOT USE VACUUM

WITHOUT INNER FILTRATION BAG IN PLACE.

CAUTION VERY FINE MATERIALS, SUCH AS FACE POWDER OR

CORNSTARCH MAY SEAL THE INNER FILTRATION BAG AND CAUSE IT TO

BURST EVEN THOUGH IT IS ONLY PARTIALLY FULL. CHANGE THE BAG OFTEN

WHEN CLEANING THIS TYPE OF MATERIAL.

Maintenance — Changing the Filtration Bag

1

Unzip the Filtration Bag Case

completely.

2

Pull the cardboard collar on the ltration

bag downward to release the bag dock

from the dock port.

3

Gently pull the cardboard collar on

the ltration bag up to engage the

SaniSeal

®

lock and remove from the

bag dock. Discard.

SaniSeal

®

OPERATION

Your Elevate

™

vacuum includes a ltration bag equipped with the SaniSeal

®

System. SaniSeal

®

automatically locks in allergens, dirt and debris each time

you change the bag.

15

4

Slide a new ltration bag collar rmly

into the bag dock ensuring all hooks

on dock door are inserted on the

cardboard collar.

5

Rotate bag dock up and press

rmly on the ltration bag at

indicated points until it snaps

into place.

6

Zip up the ltration bag

case completely.

CHANGING THE DISPOSABLE FILTRATION BAG

IMPORTANT NOTE

To keep your Elevate

™

vacuum running at optimal performance, make sure to change the ltration bag when the contents

reach the MAXIMUM FILL LINE. Overloading may result in loss of air ow suction and decreased performance.

16

Maintenance — Adjusting or Replacing Brushroll

2

Lay the unit at to access

the power head nozzle.

Remove the 7 screws to take

off the baseplate from the

power head.

1

Your Oreck

®

unit comes with

the brushroll assembled in the

“NORMAL” position (multiple

notches showing on top edge).

As the brushroll wears it can be

adjusted for longer life.

3

Remove the brushroll

belt and brushroll from the

holding channels inside of

the power head nozzle.

4

When worn, rotate both

plastic black endcaps at the

ends of the brushroll to show

a single notch “SPECIAL”

position. Insert back into the

holding channels of the power

head nozzle.

NORMAL

SPECIAL

WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY FROM MOVING PARTS - UNPLUG

BEFORE CLEANING OR SERVICING. DO NOT USE VACUUM WITHOUT THE FILTRATION BAG IN PLACE.

17

ADJUSTING OR REPLACING BRUSHROLL

5

When rotating the black

endcaps on the brushroll,

make sure both endcap

settings are the same and

faceup when you insert the

brushroll.

6

Reassemble the brushroll belt.

Reference the Maintenance

Section on Checking and

Replacing the Brushroll Belt

for details.

7

Manually spin the brushroll

to see that it turns freely.

8

Replace the 7 screws to

secure the baseplate to the

power head nozzle.

CONTACT OUR CUSTOMER CARE LINE

1-800-989-3535 (Mon-Fri 7 a.m. – 7 p.m. CST; Sat 8 a.m. – 4:30 p.m. CST)

18

Maintenance — Clearing Blockages

1

An overloaded ltration bag may cause

dirt and debris to back up into the air

ow system. Open the bag dock and

check for visible clogs at the bag port.

Change ltration bag if contents have

reached the MAXIMUM FILL LINE.

2

Also, check for blockages in the power

head nozzle.

3

If blockage is not in the power head

nozzle, remove the lower tube. Unhook

the case clasp releasing the ltration

bag case.

WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK AND INJURY FROM MOVING PARTS — UNPLUG BEFORE CLEANING OR SERVICING.

19

LUBRICATION

The motor and brushroll are equipped with bearings which contain sufcient lubrication for their

lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor or brushroll.

THE BELT

This vacuum is equipped with the Endurolife

™

Belt, which is designed for long life and doesn’t

need changing.

MOTOR PROTECTION

If the vacuum becomes overloaded (which could

occur when a large obstruction is sucked up

or when vacuuming extremely thick carpet),

the electronics are designed to shut down

the vacuum. If this happens, the vacuum will

automatically shut off and the headlights will

ash. To reset the vacuum, turn the unit “off”,

then turn on to continue use. If it shuts down

again there may be a large obstruction in the

vacuum. See Clearing Blockages for the steps on

clearing a blockage.

CLEARING BLOCKAGES

4

Twist lower tube connector

counterclockwise and slide up. Pull

the lower tube out of the fan housing.

Once removed, check for blockage.

5

If the lower tube is not blocked, look

into the fan housing for blockage. Be

sure to reassemble lower tube and

tighten the lower tube connector

before continuing use.

CONTACT OUR CUSTOMER CARE LINE

1-800-989-3535 (Mon-Fri 7 a.m. – 7 p.m. CST; Sat 8 a.m. – 4:30 p.m. CST)

WARNING TO REDUCE THE RISK OF

PERSONAL INJURY, UNPLUG BEFORE CLEANING

OR SERVICING.

20

Troubleshooting

Problem Possible Cause Possible Solution

Vacuum doesn’t run. 1. Power Cord 1. Plug in power cord.

2. On/Off Fingertip Controls 2. Push ngertip control forward to turn “ON.”

3. No voltage in the wall outlet 3. Check fuse or breaker in the home.

4. Blown fuse or tripped breaker 4. Replace fuse or reset breaker in the home.

Vacuum won’t pick up or there

is low suction.

1. Filtration Bag 1. Make sure bag is installed correctly and replace once contents reach

MAXIMUM FILL LINE.

2. Power Head nozzle 2. Check nozzle for clog and replace brushroll if worn.

3. Brushroll Belt 3. Replace belt if broken.

Service problems can often be solved easily at home. Use this guide to help you troubleshoot.

For any other service problems, contact our Customer Care Line at 1-800-989-3535 (Mon-Fri 7 a.m. – 7 p.m. CST; Sat 8 a.m. – 4:30 p.m. CST).

WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY FROM MOVING PARTS — UNPLUG BEFORE CLEANING OR SERVICING.

La page charge ...

Oreck UK30300 Mode d'emploi

Oreck UK30300 Mode d'emploi

dans d''autres langues

Documents connexes