Shindaiwa F226S Manuel utilisateur

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

F226S

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RÈGLES DE

SECURITÉ. LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN

RISQUE DE BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND

BEFOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE IN

CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA DELLE

ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

1Cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

GRASS-TRIMMER

F226S

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Contents

For safe use of your product............................................................................................... 3

Description.......................................................................................................................... 8

Before you start .................................................................................................................. 9

Packing list ....................................................................................................................9

Assembly ....................................................................................................................... 9

Preparing the fuel ........................................................................................................ 10

Engine operation............................................................................................................... 12

Starting the engine ...................................................................................................... 12

Stopping the engine..................................................................................................... 13

Trimming operation........................................................................................................... 14

Basic trimming operation with nylon line cutting head ................................................. 15

Maintenance and care ...................................................................................................... 17

Servicing guidelines..................................................................................................... 17

Maintenance and care ................................................................................................. 17

Storage ........................................................................................................................ 24

Specifications.................................................................................................................... 25

Declaration of conformity .................................................................................................. 26

3

For safe use of your product

For safe use of yo ur product

Important information

WARNING

Please ensure that you read the operator's manual before using your product.

About your operator's manual

 This manual contains necessary information about the assembly, operation, and maintenance of your product.

Please read it carefully and absorb its contents.

 Always keep your manual in a place where it is readily accessible.

 If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your dealer.

 The units used in this manual are SI units (International System of Units). Figures in parentheses are reference val-

ues, and there may be a slight conversion error in some cases.

Failure to do so could lead to an accident or serious injury.

Intended use of this product

 This product is lightweight, high-performance, petrol engined unit designed for weed control and grass trimming in

areas difficult to control by any other means.

 Do not use this unit for any purpose other than aforementioned.

 The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

 Please consult your dealer if anything is unclear or of concern.

Failure to do so could lead to an accident or serious injury.

Do not modify the product

 You must not modify the product.

To do so could lead to an accident or serious injury. Any malfunction resulting from a modification to the product will not be

covered by the manufacturer's warranty.

Do not use the product unless it has been checked and maintained

 You must not use the product unless it has been checked and maintained. Always ensure that the product is checked

and maintained on a regular basis.

Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

 When loaning your product to another party, ensure that the person borrowing the product receives the operator's

manual along with it.

 If you assign your product to another party, please enclose the operator's manual with the product when handing it

over.

Failure to do so could lead to an accident or serious injury.

Users of the product

 The product should not be used by:

 people who are tired

 people who have taken alcohol

 people who are on medication

 people who are pregnant

 people who are in poor physical condition

 people who have not read the operator's manual

 children

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

Failure to observe these instructions could lead to an accident.

 The ignition system of this product generates electromagnetic fields during operation. Magnetic fields can cause

pacemaker interference or pacemaker failure. To reduce health risks, we recommend that pacemaker users consult

their physician and the pacemaker manufacturer before operating this product.

4

For safe use of your product

Vibration and cold

 It is believed that a condition called Raynaud's Phenomenon which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers. The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ailment is unknown.

 Keep your body warm, especially the head and neck, feet and ankles, and hands and wrists.

 Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks, and also by

not smoking.

 Limit the number of hours of operation. Try to fill each day with jobs where operating the trimmer or other hand-

held power equipment is not required.

 If you experience discomfort redness and swelling of the fingers, followed by whitening and loss of feeling, con-

sult your physician before exposing yourself further to cold and vibration.

Failure to observe these instructions could result in damage to your health.

Repetitive stress injuries

 It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive stress injury (RSI). To reduce the risk of RSI, do the following:

 Avoid using your wrist in a bent, extended or twisted position.

 Take periodic breaks to minimize repetition and rest your hands. Reduce the speed and force in which you do the

repetitive movement.

 Do exercises to strengthen hand and arm muscles.

 See a doctor if you feel tingling, numbness or pain in your fingers, hands, wrists or arms. The sooner RSI is diag-

nosed, the more likely permanent nerve and muscle damage can be prevented.

Failure to observe these instructions could result in damage to your health.

Proper training

 Do not permit operation without proper training and protective equipment.

 Be thoroughly familiar with the controls and proper use of unit.

 Know how to stop the unit and shut off the engine.

 Know how to unhook a harnessed unit quickly.

 Never allow anyone to use the unit without proper instruction.

Failure to observe these instructions could result in damage to your health.

Wear proper clothing.

 Secure hair so it is above shoulder length.

 Do not wear ties, jewellery, or loose, dangling clothing which could be caught in the

unit.

 Do not wear open toed footwear, or go bare-foot or barelegged.

Failure to observe these precautions could result in damage to your sight or hearing, or lead

to a serious injury.

Wear protective gear

 Always wear the following protective gear when working with the trimmer.

1. Head protection (helmet): Protects the head

2. Ear muffs or ear plugs: Protect the hearing

3. Safety goggles: Protect the eyes

4. Face shield: Protects the face

5. Safety gloves: Protect the hands from cold and vibration

6. Work clothes that fit (long sleeves, long trousers): Protect the body

7. Heavy duty, non-slip protective boots (with toecaps) or non-slip work shoes

(with toecaps): Protect the feet

8. Shin guards: Protect the legs

Failure to observe these precautions could result in damage to your sight or hearing, or

lead to a serious injury.

 When necessary, please use the protective gear below.

 Dust mask: Protects the breathing apparatus

 Bee net: To deal with attacks by bees

WARNING

5

For safe use of your product

Warning notices

Other indicators

Symbols

Environment of use and operation

Do not use the product:

 under poor weather conditions.

 on steep slopes or in places which give no secure foothold and are thus slippery.

 at night or in dark places with poor visibility.

 When using the product on a gentle slope, work in a level, contour-like motion.

A serious injury could result if you fall or slip, or fail to operate the product correctly.

 For your own health and your safe and comfortable work, operate the machine within the air temperature range of

−5

o

C to 40

o

C.

Failure to observe these instructions could result in damage to your health.

Being prepared in case of an injury

 In the unlikely event of an accident or injury, please ensure that you are

prepared.

 First aid kit

 Towels and wipes (to stop any bleeding)

 Whistle or mobile phone (for calling outside help)

If you are unable to perform first aid or call for outside help, the injury could

worsen.

Put safety first in the case of fire or smoke

 If fire comes from the engine or smoke appears from any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safety.

 Use a shovel to throw sand or other such material on the fire to prevent it from spreading, or put it out

with a fire extinguisher.

A panicked reaction could result in the fire and other damage becoming more extensive.

WARNING

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual

The maximum speed of the

cutting attachment shaft in

r/min

Wear eyes, ears and head

protection

Keep bystanders away 15 m

6

For safe use of your product

Wear foot protection and

gloves

Petrol and oil mixture

Emergency stop

Choke Control "Cold Start"

Position (Choke Closed)

Warning!

Thrown objects!

Choke Control "Run" Position

(Choke Open)

Warning, side thrust

Carburettor adjustment

- Idle speed

Usage without shield not per-

mitted

Beware of high-temperature

areas

Usage of metal blades not

permitted

Guaranteed sound power lev-

el

Do not use the product in plac-

es with poor ventilation

Engine start

Beware of fire Beware of electric shocks

-

Purge bulb (Primer)

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

7

For safe use of your product

Safety decal(s)

 The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

 If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

1. Safety decal (Part number X505-000140)

2. Safety decal (Part number X505-002310)

8

Description

1. Cutting attachment Nylon line cutting head for cutting

grass and weed.

2. Shield Device to protect the operator from accidental

contact with the cutting head and thrown objects.

3. Cut off knife Cut nylon line to adjust line length to prop-

er swath.

4. Shaft tube Part of the unit that provides a casing for

power transmission shaft.

5. Loop-handle Light weight, suitable for nylon line trim-

mer.

6. Ignition switch "Slide switch" mounted on top of the

throttle trigger housing, move switch forward to RUN,

backward to STOP position.

7. Throttle trigger Activated by the operator's finger for

controlling the engine speed.

8. Throttle trigger lockout Locks throttle trigger in the

idling position until you have a proper grip with your right

hand around the handle.

9. Grip Rear (right hand) handle.

10. Air cleaner cover Covers air filter.

11. Fuel tank Contains fuel and fuel filter.

12. Fuel tank cap For closing the fuel tank.

13. Starter handle Pull handle to start the engine.

14. Silencer cover Cover the silencer not to make operator

touch to hot surface of silencer.

15. Spark plug

16. Safety decal

17. Type and serial number

9

Before you start

Packing list

Assembly

Loop handle assembly

Position handle (A) in comfortable operating position and tighten

screws (M5×35) (B). The cutting attachment should be 5 - 7.5 cm

above the ground and as level as possible.

 The following parts are packed separately in the packing box.

 When you have unpacked the box, please check the parts that it contains.

 Contact your dealer if anything is missing or broken.

1. Engine and shaft tube

2. Wing nut

3. Washer

4. Bolt

5. Shield

6. Nylon line cutting head

7. Operator's manual

8. Loop handle

9. Locking tool

10. Socket wrench

11. L-wrench

WARNING

 Read the operator's manual carefully to ensure that you assemble the product correctly.

Using a product that has been incorrectly assembled could lead to an accident or serious injury.

10

Before you start

Installation of shield

1. Remove plastic sleeve (B) from output shaft (C).

2. Snap the shield (D) over the bearing housing (E).

3. Install bolt (F), washer (G) and wing nut (H).

Installing nylon line cutting head

1. Rotate output shaft until holes in fixing plate (A) and in bear-

ing housing are aligned.

2. Insert locking tool (B) through these holes.

3. Install nylon line head (C) to output shaft rotating clockwise.

4. Remove locking tool.

Preparing the fuel

WARNING

 Cut off Knife (A) on debris shield has sharp edges.

Avoid contact when installing or removing line head.

 Failure to do so could lead to an injury or serious accident.

DANGER

 Do not fuel up while the engine is hot or in operation.

 Do not smoke or hold a flame near when refuelling.

If you do so, the fuel could ignite and cause fire, leading to burns.

WARNING

 Do not fill fuel tanks indoors. Always fill fuel tanks outdoors over bare ground. Do not refuel the product on the load-

ing platform of a truck, or in other such places.

 Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

Otherwise, fuel may get spewed.

 Mop up any fuel that overflows or spills out due to overfilling.

Fuel spills can cause fire and burns when ignited.

 After refuelling, always check that there are no leaks or discharges of fuel from the fuel pipe, fuel system grommets,

or around the fuel tank cap. If you do find fuel leaks or discharges, stop using the product immediately and contact

your dealer to have it repaired.

Any fuel leaks could cause fire.

 Keep the refuelling tank in a shaded area away from fire.

 Use an approved fuel container.

IMPORTANT

 Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine oil. Minimum 89 Octane unleaded petrol is recom-

mended. Do not use fuel containing methyl alcohol or more than 10 % of ethyl alcohol.

 Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days.

11

Before you start

Fuel

 Recommended mixture ratio; 50: 1 (2%) for ISO-L-EGD

Standard (ISO/CD 13738), JASO FC,FD grade and shindaiwa

recommended oil.

 Never use two-stroke oil intended for water-cooled engines,

motor-cycle engines.

 Do not mix directly in engine fuel tank.

Fuel supply

 Do not add so much fuel that it reaches the mouth of the fuel

tank (A). Keep the fuel within the prescribed level (up to the

shoulder level (B) of the fuel tank).

 Tighten the fuel tank cap securely after refuelling.

12

Engine operation

Starting the engine

Starting a cold engine

(Connect the spark plug cap if the product has been in storage for

a long period of time.)

1. Placing the product on level ground, check to ensure that the

cutting attachment does not come into contact with the sur-

face of the ground or any other impediment using a beam or

other such implement.

2. Move the ignition switch (A) to the Start position.

3. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

4. Move the choke lever (F) to the "Cold Start" (E) position.

5. Alternately press and release the purge bulb (H) until the fuel

is sucked up into it.

6. Checking that the area around you is safe, hold the position

closest to the engine firmly as shown in the illustration, pull-

ing several times on the starter grip (I).

7. If you hear an explosion-like sound and the engine stops im-

mediately, move the choke lever to the "Run" (G) position

and continue pulling on the starter grip to start the engine.

8. If the engine does not stop, return the choke lever gently to

WARNING

Be particularly careful to observe the following precautions when starting the engine:

 Move at least 3m from the place where you refuelled.

 Place the product in a flat, well ventilated place.

 Check that there are no fuel leaks.

 Check that none of the nuts and bolts are loose.

 Leave plenty of space around the product and do not allow people or animals near it.

 Start the engine with the throttle trigger in the idle speed position.

 Hold the product firmly to the ground when starting the engine.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

 Check that there are no abnormal vibrations or sounds once the engine starts. Do not use the product if there are

abnormal vibrations or sounds. Contact your dealer to have it repaired.

Accidents involving parts that fall or shatter off can cause wounds or serious injury.

 The exhaust fumes from the engine contain toxic gases. Do not operate the product indoors or in other

ill ventilated places.

The exhaust fumes could cause poisoning.

 Do not touch silencer, spark plug, angle transmission, and other high temperature components while

the product is running or for some time after it stops.

You could burn yourself if you touch a high temperature component.

 Do not touch spark plug, spark plug wire, and other high voltage components while the product is run-

ning.

You could receive an electric shock if you touch a high voltage component while the product is running.

 If the cutting attachment rotates even though the throttle trigger is in the idle speed position when the engine is start-

ed, adjust the carburettor before using the product.

Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

NOTE

 Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.

 Do not let go of the starter grip as it returns.

13

Engine operation

the "Run" position.

9. Leave the engine to warm up at idle speed for a while.

Starting a warm engine

1. Move the ignition switch (A) to the Start position.

2. Make sure that the throttle trigger (D) is at the idle speed po-

sition.

3. Check that the choke lever is in the "Run" position.

4. If no fuel is visible in the purge bulb, alternately press and re-

lease the purge bulb until the fuel is sucked up into it.

5. Checking that the area around you is safe, hold the position

closest to the engine firmly, and pull on the starter grip to

start the engine.

Stopping the engine

1. Move the throttle trigger (B) to the idle speed position and set

the engine to idling (i.e. low speed).

2. Move the ignition switch (A) to the Stop position.

3. In the event of an emergency, stop the engine immediately

using the ignition switch.

4. If the engine fails to stop, move the choke lever to the "Cold

Start" position. The engine will stall and come to a halt (an

emergency stop).

 If the engine fails to stop when the ignition switch is used, have

the ignition switch checked and repaired by your dealer before

you use the product again.

5. Always disconnect the spark plug wire from the spark plug to

ensure the engine cannot be started before you work on the

unit or leave it unattended.

14

Trimming operation

DANGER

 Always stop the engine when a cutting attachment jam occurs.

Severe injury can occur if a jam is removed and the cutting attachment suddenly starts.

 Do not operate the product without the shield in place.

Any objects that ricochet off the cutting attachment could cause an accident or serious injury.

 The area within a 15 m radius of the product is a danger zone. Be care-

ful to observe the following precautions while working with the prod-

uct.

 Do not allow children and other people or pets to enter the danger

zone.

 If another person enters the danger zone, turn off the engine to stop

the cutting attachment from rotating.

 When approaching the operator, signal to him by, for example,

throwing twigs from outside the danger zone, and then check that

engine has been switched off and the cutting attachment has

stopped turning.

 If more than one person is working with the product, identify the way

in which you will signal to each other and work at least 15 m apart.

Any objects that ricochet off the cutting attachment, and any contact with the cutting attachment, could cause blindness or a

fatal accident.

WARNING

 Before starting work, check the area where you will be working and remove any small stones

and empty cans likely to ricochet off the cutting attachment, as well as any pieces of string

or wire that might become twisted around the cutting attachment.

An accident or serious injury can occur if foreign objects ricochet off the cutting attachment or wire

and other materials twisted round the product spring off it.

 In the following situations, turn off the engine immediately and ensure that the cutting attachments have stopped

before checking each area of the product. Replace any damaged parts.

 If the cutting attachment hits a rock, tree, post, or other such obstruction while you work.

 If the product suddenly starts to vibrate abnormally.

Continuing to use parts when they are damaged could lead to an accident or serious injury.

 Do not hold the cutting attachment up while you work. You must not work with the cutting attachments raised above

knee level.

Raising the cutting attachment above knee level brings the plane of rotation closer to the face, and any objects that fly off the

cutting attachments could cause an accident or serious injury.

Transport of the product

 When transporting in the situations described below, turn off the engine and ensure that the cutting attachment has

stopped rotating, then position the silencer away from yourself.

 Moving to the place where you are working.

 Moving to another area while you are working.

 Leaving the place where you have been working.

Failure to observe these precautions could cause burns or serious injury.

 When transporting the product by car, empty the fuel tank and secure the product firmly in place to prevent it from

moving around.

Travelling by car with fuel in the fuel tank could lead to a fire.

 Never attempt to operate the product with one hand.

 Ensure that you hook your thumbs around the grips, wrapping them in your thumb

and remaining fingers.

15

Trimming operation

Basic trimming operation with nylon line cutting head

Adjusting nylon line

 Do not rotate the nylon line cutting head at more than 10000 r/

min.

 When releasing nylon line from spool, hit tap knob of spool

against the ground surface lightly at rotation speed lower than

4500 r/min.

 Cut off knife on the shield adjusts cutting swath automatically

by cutting nylon lines evenly when attachment starts rotating.

 When operating with less than maximum cutting swath, cut

two nylon lines in equal lengths.

 When nylon line becomes shortened, hit tap knob (A) of spool

against the ground surface lightly and the line is released from

spool to come out.

Trimming

 This is feeding the trimmer carefully into the material you wish

to cut. Tilt the head slightly to direct the debris away from you.

If cutting up to a barrier such as a fence, wall or tree, approach

from an angle where any debris ricocheting off the barrier will

fly away from you.

 Move the nylon line cutting head slowly until the grass is cut

right up to the barrier, but do not jam (overfeed) the line into

the barrier. If trimming up wire mesh or chain link fencing, be

careful to feed only up to the wire. If you go too far, the line will

snap off around the wire.

 Trimming can be done to cut through weed stems one at a

time. Place the nylon line cutting head near the bottom of the

weed never high up, which could cause the weed to chatter

and catch the line. Rather than cut the weed right through, just

use the very end of the line to wear through the stem slowly.

1. Angle to wall

2. Debris

3. Knife side raised

4. Angle to ground

Scything

 This is the cutting or mowing of large grassy areas by sweep-

ing or swinging the trimmer in a level arc. Use a smooth, easy

motion. Do not try to hack or chop down the grass. Tilt the ny-

lon line cutting head to direct the debris away from you on the

scything stroke. Then return without cutting grass for another

stroke. If you are well protected and do not care whether some

debris is thrown in your direction, you may scythe in both di-

rections.

WARNING

 Serious injury may result from the improper use of cutting attachment. Read and comply with all safety instructions

listed in this manual.

 Use only cutting attachments recommended by YAMABIKO Corporation.

 Excessive nylon line beyond cut off knife could fly off when the nylon line cutting head starts rotating after adjust-

ment of nylon line length.

Failure to do so could lead to an accident or serious injury.

16

Trimming operation

Scalping and edging

 Both of these are done with the nylon line cutting head tilted at

a steep angle. Scalping (A) is removing top growth, leaving the

earth bare. Edging (B) is trimming the grass back where it has

spread over a pavement or driveway. During both edging and

scalping, hold the unit at a steep angle in a position where the

debris, and any dislodged dirt and stone, will not come back

towards you even if it ricochets off the hard surface.

 Although the pictures show how to edge and scalp, every op-

erator must find for himself the angles which suit his body size

and cutting situation.

 For nearly all cutting, it is good to tilt the nylon line cutting head

so that contact is made on the part of line circle where the line

is moving away from you and the shield (See appropriate pic-

ture). This results in the debris being thrown away from you.

 Tilting the head to the wrong side will shoot the debris toward

you. If the nylon line cutting head is held flat to the ground so

that cutting occurs on the whole line circle, debris will be

thrown at you, drag will slow the engine, and you will use up a

lot of line.

 Nylon line cutting head rotates clockwise. The knife will be on

the right side of the shield.

1. Debris

2. Cut on this side

 Do not push the line into tough weeds, trees, or wire fences.

 Pushing the line into chicken wire, chain link fencing or thick

brush can result in snapped-off line ends being hurled back at

the operator. The proper way is to cut right up to a barrier, such

as any of those mentioned, but never run the line into or

through the obstruction. Do not cut closely to obstruction or

barrier.

 Avoid nylon line contact with broken wire fencing. Pieces of

wire broken off by the trimmer can be hurled at high speeds.

17

Maintenance and care

Servicing guidelines

Maintenance and care

WARNING

Observe the following precautions when checking and maintaining your product after use:

 Turn the engine off and do not attempt to check or maintain the product until the engine has cooled.

You could burn yourself.

 Remove the spark plug cap before performing checks and maintenance.

An accident could occur if the product starts unexpectedly.

IMPORTANT

 Checking and maintenance requires specialist knowledge. If you are unable to check and maintain the product or deal with a

fault yourself, consult your dealer. Do not attempt to dismantle the product.

 For spare parts and consumables, please use only genuine parts and designated products and components. Using parts from

other manufacturers or non-designated components may result in a malfunction.

Area Maintenance Page Before use Monthly

Air filter Clean/Replace 18 •

Fuel filter Inspect/Clean/Replace 18 •

Spark plug Inspect/Clean/Adjust/Replace 20 •

Carburettor Adjust/Replace and adjust 18 •

Cooling system Inspect/Clean 19 •

Silencer Inspect/Tighten 19 •

Silencer Clean 19 •**

Drive shaft Grease 20 •*

Starter Inspect - •

Cut off knife Inspect/Clean - •

Fuel system Inspect 18 •

Screws, bolts and nuts Inspect, Tighten/Replace - •

* Or 50 hours, whichever occurs first. ** Or 100 hours, whichever occurs first.

IMPORTANT

 Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance.

If you have any questions or problems, please contact your dealer.

18

Maintenance and care

Cleaning air filter

 Close choke. Loosen wing bolt (A) and remove air cleaner

cover (B).

 Remove air filter (C) (air filter is located inside air cleaner cov-

er).

 Brush dirt from filter or clean with compressed air.

 Reinstall filter.

 Reinstall cover and tighten wing bolt.

Replacing fuel filter

1. Use a piece of metal wire or the like to pick up fuel filter (A)

through fuel tank opening.

2. Pull old filter from fuel line (B).

3. Install new fuel filter.

Carburettor adjustment

Every unit is test run at the factory and the carburettor is fine

tuned for maximum performance.

Before adjusting carburettor, clean or replace air filter, start en-

gine and run several minutes to bring it to operating temperature.

To adjust the carburettor proceed as follow:

Turn "idle" speed adjustment screw (T) clockwise until cutting

attachment begins to turn, then turn screw(T) out anticlock-

wise until cutting attachment stops turning. Turn screw (T) out,

anticlockwise, and additional 1 turn.

NOTE

 If filter is excessive dirty or no longer fits properly, replace it.

WARNING

 YOU MAY ADJUST THE IDLE SPEED ONLY by turning the idle speed adjustment screw (T).

 During carburettor adjustment, the cutting attachment may move. Pay utmost attention and care to the cutting at-

tachment so as not to get injured by the moving cutter.

 When carburettor adjustment is completed, the cutting attachment should not move at idle speed, otherwise serious

personal injury may result.

 You must NOT carry out any Carburettor adjustment, other than the idle speed. All other adjustments MUST be per-

formed by an authorized service dealer, or serious personal injury may result due to malfunction of the engine.

CAUTION

 When there is trouble with the carburettor, contact an authorized service dealer.

NOTE

When the carburettor cannot be adjusted properly with the idle

speed adjustment screw (T), you must contact an authorized

service dealer.

La page est en cours de chargement...

Shindaiwa F226S Manuel utilisateur

Shindaiwa F226S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents