Echo GT-225 Manuel utilisateur

Grass Trimmer

Operator's Manual

MODEL GT-225

WARNING

Read rules for safe operation and instructions carefully. ECHO provides an Opera-

tor's Manual and a Safety Manual. Both must be read and understood for proper and

safe operation.

X7722271502

X772000142

10/09

2

In t r o d u c t I o n

Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-

job-dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You

will nd both easy to use and full of helpful operations tips and SAFETY messages.

t h e o p e r a t o r 's m a n u a l

Read and understand this manual before operation. Keep it in a safe

place for future reference. It contains specications and information

for operation, starting, stopping, maintenance, storage, and assembly

specic to this product.

t h e s a f e t y m a n u a l

Read and understand this manual before operation. Keep it in a safe

place for future reference. It explains possible hazards involved with

the use of Grass Trimmers and Brush cutters and what measures you

should take to make their use safer.

ta b l e o f co n t e n t s

Introduction ................................................................2

- The Operator's Manual .......................................2

- The Safety Manual ..............................................2

Safety .........................................................................3

- Manual Safety Symbols and Important

Information .........................................................3

- International Symbols .........................................3

- Personal Conditions and Safety Equipment .......4

- Equipment ...........................................................6

Emission Control .......................................................7

Description .................................................................7

Contents ....................................................................9

Assembly....................................................................9

- Plastic Shield Installation .................................10

- Nylon Head Installation ....................................10

- Nylon Line Installation .....................................10

- Front (Loop) Handle .........................................11

Operation .................................................................. 11

- Fuel ...................................................................11

- Starting Cold Engine .........................................13

- Starting Warm Engine .......................................14

- Stopping Engine ................................................14

Maintenance .............................................................15

- Skill Level .........................................................15

- Maintenance Intervals .......................................15

- Air Filter ...........................................................16

- Fuel Filter ..........................................................16

- Spark plug .........................................................17

- Cooling System .................................................17

- Exhaust System .................................................18

- Carburetor Adjustment ......................................19

- High Altitude Operation ..........................................19

- Lubrication ........................................................20

Troubleshooting .......................................................21

Storage .....................................................................22

Specications ...........................................................23

Warranty Statements ..........................................................24

Servicing Information ..............................................28

- Parts/Serial Number ..........................................28

- Service ..............................................................28

- ECHO Consumer Product Support ...................28

- Warranty Card ...................................................28

- Additional or Replacement Manuals ................28

Specications, descriptions and illustrative material in this

literature are as accurate as known at the time of publica-

tion, but are subject to change without notice. Illustrations

may include optional equipment and accessories, and may

not include all standard equipment.

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

3

I n t e r n a t I o n a l s y m b o l s

BEWARE

- THROWN,

RICOCHET

OBJECTS

WEAR HAND AND

FOOT PROTECTION

HOT

SURFACE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

READ AND UNDER-

STAND OPERATOR'S

MANUAL.

WEAR EYES, EARS

AND HEAD PROTEC-

TION

FUEL AND OIL

MIXTURE

SAFETY/ALERT

DO NOT SMOKE

NEAR FUEL.

WEAR SLIP RE-

SISTANT FOOT

WEAR.

DO NOT EXCEED

10,000 RPM.

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

SYMBOL

DESCRIPTION/APPLICATION

SYMBOL FORM/

SHAPE

CARBURETOR AD-

JUSTMENT

- IDLE SPEED

CARBURETOR AD-

JUSTMENT

- HIGH SPEED

MIXTURE

EMERGENCY STOP

CARBURETOR AD-

JUSTMENT

- LOW SPEED MIX-

TURE

DO NOT ALLOW

FLAMES OR

SPARKS NEAR

FUEL.

IGNITION

ON/OFF

PRIMER

BULB

KEEP BYSTANDERS AND HELPERS

AWAY 15 M (50 FT.).

CHOKE CONTROL

"COLD START"

POSITION

(CHOKE CLOSED)

CHOKE CONTROL

"RUN"

POSITION

(CHOKE OPEN)

DO NOT USE

BLADES. STRING

LINE ONLY

BEWARE

- THROWN,

RICOCHET

OBJECTS

CAUTION

The safety alert symbol accompanied by the word

“CAUTION” calls attention to an act or condition

which may lead to minor or moderate personal

injury if not avoided.

sa f e t y

m a n u a l

s a f e t y s y m b o l s a n d I m p o r t a n t I n f o r m a t I o n

WARNING

The safety alert symbol accompanied by the word

“WARNING” calls attention to an act or condi-

tion which CAN lead to serious personal injury or

death if not avoided.

CIRCLE AND SLASH SYMBOL

This symbol means the specic action

shown is prohibited. Ignoring these prohi-

bitions can result in serious or fatal injury.

NOTE

This enclosed message provides tips for use, care and

maintenance of the unit.

IMPORTANT

The enclosed message provides information neces-

sary for the protection of the unit.

DANGER

The safety alert symbol accompanied by the word

“DANGER” calls attention to an act or condition

which WILL lead to serious personal injury or

death if not avoided.

Throughout this manual and on the product itself, you will nd safety alerts and helpful, informational messages pre-

ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean

to you.

ROTATING

CUTTING ATTACH-

MENT

4

Physical Condition

Your judgment and physical dexterity may not be good:

• if you are tired or sick,

• if you are taking medication,

• if you have taken alcohol or drugs.

Operate unit only if you are physically and mentally well.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE re-

quirements whenever you operate the unit.

Hand Protection

Wear no-slip, heavy-duty work gloves to improve your

grip on the handles. Gloves also reduce the transmission

of machine vibration to your hands.

Hearing Protection

ECHO recommends wearing hearing protection whenever

unit is used.

Vibration and Cold --

It is believed that a condition called Raynaud’s Phenomenon, which affects the ngers of certain individuals, may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-

sations, followed by loss of color and numbness in the ngers. The following precautions are strongly recommended,

because the minimum exposure which might trigger the ailment is unknown.

• Keep your body warm, especially the head, neck, feet,

ankles, hands, and wrists.

• Maintain good blood circulation by performing vigor-

ous arm exercises during frequent work breaks, and

also by not smoking.

• Limit the hours of operation. Try to ll each day with

jobs where operating the unit or other hand-held power

equipment is not required.

• If you experience discomfort, redness, and swelling of

the ngers followed by whitening and loss of feeling,

consult your physician before further exposing yourself

to cold and vibration.

p e r s o n a l c o n d I t I o n a n d s a f e t y e q u I p m e n t

WARNING

Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly and

or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a trimmer.

Proper Clothing

Wear snug tting, durable clothing;

• Pants should have long legs, shirts with long sleeves.

• DO NOT WEAR SHORTS,

• DO NOT WEAR TIES, SCARFS, JEWELRY.

Wear sturdy work shoes with nonskid soles;

• DO NOT WEAR OPEN TOED SHOES,

• DO NOT OPERATE UNIT BAREFOOTED.

Keep long hair away from engine and air intake. Retain

hair with cap or net.

Hot Humid Weather

Heavy protective clothing can increase operator fatigue

which may lead to heat stroke. Schedule heavy work for

early morning or late afternoon hours when temperatures

are cooler.

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

5

Repetitive Stress Injuries --

It is believed that overusing the muscles and tendons of the ngers, hands, arms, and shoulders may cause soreness,

swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high

risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which

could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged

exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended, or twisted position.

Instead try to maintain a straight wrist position. Also, when grasping,

use your whole hand, not just the thumb and index nger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive move-

ment.

• Do exercises to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if

you feel tingling, numbness, or pain in the ngers, hands, wrists, or

arms. The sooner RSI/CTS is diagnosed, the more likely permanent

nerve and muscle damage can be prevented.

DANGER

Do not operate this product indoors or in inadequately ventilated

areas. Engine exhaust contains poisonous emissions and can cause

serious injury or death.

Read the Manuals

• Provide all users of this equipment with the Operator’s Manual and

Safety Manual for instructions on Safe Operation.

Clear the Work Area

• Spectators and fellow workers must be warned, and children and

animals prevented from coming nearer than 15 m (50 ft.) while the

unit is in use.

Keep a Firm Grip

• Hold the front and rear handles with both hands, with thumbs and

ngers encircling the handles.

Keep a Solid Stance

• Maintain footing and balance at all times. Do not stand on slippery,

uneven or unstable surfaces. Do not work in odd positions or on lad-

ders. Do not over reach.

Avoid Hot Surfaces

• Keep exhaust area clear of ammable debris. Avoid contact during

and immediately after operation.

6

WARNING

Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings.

• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop

before removing obstructions, clearing debris, or servicing unit.

• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.

• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.

e q u I p m e n t

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.

• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is damaged or miss-

ing.

• Check that the cutting attachment is rmly attached and in safe operating condition.

• Check that front (loop) handle and optional shoulder/waist harness are adjusted for safe, comfortable operation. See

Assembly for proper adjustment.

WARNING

Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment com-

bination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which

have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and

safety manual.

An Emission Control Label is located on the engine. (This is an EXAMPLE ONLY, information on label varies by

engine FAMILY).

WARNING

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found,

do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an autho-

rized servicing dealer before using.

em I s s I o n co n t r o l (e x h a u s t & e v a p o r a t I v e )

EPA 2010 and Later

The emission control system for the engine is EM/TWC (Engine Modication and 3-way Catalyst) and for the fuel tank

the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to

California models only.

PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)

The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-

sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed

as listed in the Maintenance Section of this manual.

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

7

3

4

5

6

7

8

2

9

de s c r I p t I o n

Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the instruc-

tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING

instructions for specic information.

Shaft Decal

P/N X505002310

Hot Decal (near mufer)

P/N X505002500

P/N X505001930

1

10

12

14

17

15

16

18

11

13

8

1. POWER HEAD - Factory Assembled to the Driveshaft assembly. Includes the Engine, Clutch, Fuel System, Igni-

tion System and Recoil Starter.

2. GRIP - Rear (right hand) handle.

3. STOP SWITCH - "SLIDE SWITCH" mounted on top of the Throttle Trigger Housing. Move switch FORWARD

to RUN, BACK to STOP.

4. FRONT HANDLE - The Front (loop) handle is factory assembled to the Drive Shaft assembly but must be re-posi-

tioned for proper cutting attitude and operator comfort.

5. DRIVESHAFT ASSEMBLY - Factory Assembled to the Power Head. Includes the Rear (right hand) Handle As-

sembly, Bearing Housing Assembly, Throttle Trigger, Front (loop, left hand) Handle Assembly, Flexible Drive Cable

and Safety Decals.

6. RAPID LOADER

TM

HEAD - Contains replaceable nylon trimming lines.

7. PLASTIC DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before

use, see Assembly Instructions. Shield assembly includes the Cut-Off Knife. Mounts on the Gear Housing Assem-

bly just above the cutting attachment. Helps protect the operator by deecting debris produced during the trimming

operation.

8. CUT-OFF KNIFE - Trims line to the correct length.

9. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradu-

ally for best operating technique.

10. TOP GUARD - Provides arm rest during operation and protects arm from hot engine.

11. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST -The mufer or

catalytic mufer controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of

carbon from leaving the mufer. Keep exhaust area clear of ammable debris.

12. FUEL TANK - Contains fuel and fuel lter.

13. i-30 Recoil Starter/Handle - i30 spring-assisted recoil starter requires 30% less pulling force than standard recoil

starter. Pull handle slowly until starter engages, then quickly and rmly. When engine starts, return handle slowly.

DO NOT let handle snap back or damage to unit will occur.

14. FUEL TANK CAP - Cover and seals fuel tank opening.

15. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from

the carburetor. Pump purge bulb until fuel is visible and ows freely in the clear fuel tank return line. Pump purge

bulb an additional 4 or 5 times.

16. CHOKE - Located at the rear of the air cleaner housing. Move choke lever to "Cold Start" ( ) to close choke for

cold starting. Move choke lever to "Run" ( ) position to open choke.

17. AIR CLEANER - Contains replaceable lter element.

18. SPARK PLUG - Provides spark to ignite fuel mixture.

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

9

_____ - Trimmer Assembly:

_____ - Power Head

____ - Drive Shaft Assembly

_____ - Plastic Bag (Co-Pack)

_____ - Operator's Manual

_____ - Safety Manual

_____ - Warranty Card & Limited Warranty

_____ - Locking Tool, P/N 89751801131 (head locking tool)

_____ - Safety Glasses

_____ - Echo Power Blend X

TM

2-stroke oil sample

_____ - 12 pcs. 8 in. x .080 Pre-cut Nylon Line

_____ - Rapid Loader

TM

2-line Head

_____ - Shield Assembly

_____ - Line Head Mounting Hardware:

_____ - 3/8-24 Locknut

_____ - Small Washer

_____ - Large Washer

*____ - Locking Tool, P/N 89751801131 (wrench handle)

*____ - Wrench 17 x 14.5, P/N X602000031

as s e m b l y

Tools Required: Locking Tools (2), Wrench 17 x 14.5 (9/16 in.)

Parts Required: Rapid Loader

TM

Head, Large washer, Small washer,

3/8-24 Locknut, (2) Pre-cut Nylon Line 8 in. x .

080 in., Plastic Shield Assembly

WARNING

Cut-off knife on debris shield has sharp edges. Avoid contact when

installing or removing line head.

co n t e n t s

The ECHO product you purchased has been partially assembled for your convenience. Due to packaging restrictions,

installation of the plastic debris shield, nylon line head, and positioning of the front handle may be necessary.

After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing

parts. Use the contents list to check for missing parts.

* Some Echo units may be factory pre-assembled. The nylon line head, plastic debris shield, and mounting hardware

shown in the contents list are pre-assembled to the unit. Assembly tools are not supplied with these units. The front

handle may need to be re-positioned for comfortable operation.

10

p l a s t I c s h I e l d I n s t a l l a t I o n

CAUTION

Wear Gloves or personal injury may result:

• Cutoff knife is sharp.

• Gearcase and surrounding area may be hot.

1. Remove wing nut (A), washer (B), and bolt (C).

2. Snap the shield over the bearing housing.

3. Install bolt (C), washer (B), and wing nut (A).

n y l o n l I n e h e a d I n s t a l l a t I o n

1. Remove plastic threaded shaft sleeve from threaded PTO shaft.

2. Align locating hole in upper plate with hole in bearing housing and

insert 5 mm (3/16 in.) diameter locking tool (A).

3. Place large washer (B) then line head (C) on threaded shaft, fol-

lowed by small metal washer (D) and locknut (E).

4. Install 3/8-24 locknut using 14.5 mm (9/16 in.) wrench. Turn lock-

nut clockwise, and tighten securely.

IMPORTANT

Remember to remove the locking tool.

IMPORTANT

Semi-automatic nylon line heads must be used only with plastic

debris shield with cut-off knife

C

A

B

A

B

C

D

E

n y l o n l I n e I n s t a l l a t I o n

1. Shut engine off. Lay unit on the ground with head assembly up.

2. Remove old nylon line through center recess of head.

3. Thread new lines through outside holes (A) in housing until ends

meet in center of recess.

NOTE

Insert cutting line ends to center of head recess to insure easy

removal of used lines.

A

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

11

mIn

spacInG

f r o n t (l o o p ) h a n d l e

NOTE

Label shows minimum spacing for front handle location.

NOTE

Front handle is pre-installed. Re-positioning and tightening is all

that is required.

1. Position front handle (A) in comfortable operating position and

tighten wing nut (B). The cutting attachment should be 5-7.5 cm

(2-3 in.) above the ground and as level as possible.

A

B

f u e l

NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor perfor-

mance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage

section of this

manual.

WARNING

Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete

stop before removing obstructions, clearing debris, or servicing unit.

op e r a t I o n

WARNING

Operation of this equipment may create sparks that can start res around dry vegetation. This unit is equipped

with a spark arrestor and a spark arrestor may be required. The operator should contact local re agencies for

laws or regulations relating to re prevention requirements.

WARNING

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconscious-

ness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed

away from your face and body.

12

IMPORTANT

Echo premium Power Blend X

TM

Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo

engines sold in the past regardless of ratio specied in those manuals.

Handling Fuel

DANGER

Fuel is VERY ammable. Use extreme care when mixing, storing or handling or serious personal injury may result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow ames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT or RUNNING!

• DO NOT ll fuel tanks indoors. ALWAYS ll fuel tanks outdoors over bare ground.

• DO NOT overll fuel tank. Wipe up spills immediately.

• Securely tighten fuel tank cap and close fuel container after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

• Move at least 3m (10 ft.) from refueling location before starting the engine.

Mixing Instructions

1. Fill an approved fuel container with half of the required amount of gasoline.

2. Add the proper amount of 2-stroke oil to gasoline.

3. Close container and shake to mix oil with gasoline.

4. Add remaining gasoline, close fuel container, and remix.

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-

off containers to reduce fuel spillage.

After use

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return unused fuel to an approved fuel storage container.

Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a pre-

caution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks

and ames.

Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must

be used. Echo brand premium Power Blend X

TM

Universal 2-Stroke Oil meets these standards. Engine problems due to

inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD certied oil, such as

Echo premium Power Blend X

TM

, will void the two-stroke engine warranty.

Fuel Requirements

Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to

10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol)

is NOT approved.

WARNING

Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements

are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance

problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited

to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets,

carburetors and other engine components.

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

13

IMPORTANT

Stored fuel ages. Do not mix more fuel than you expect to use in thirty (30) days, ninety (90) days when a fuel

stabilizer is added.

IMPORTANT

Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use.

s t a r t I n G c o l d e n G I n e

WARNING

The attachment will operate immediately when the engine starts

and could result in loss of control and possible serious injury. Keep

movable parts of the attachment off the ground and away from

objects that could become entangled or thrown.

1. Stop Switch

Move stop switch (A) away from the STOP position.

2. Choke

Move choke (B) to “Cold Start” ( ) Position.

3. Purge Bulb

Pump purge bulb (C) until fuel is visible and ows freely in

the clear fuel tank return line. Pump bulb an additional 4 or 5

times.

4. Recoil Starter

Lay the unit on a at area and keep movable attachment parts clear

of all obstacles. Firmly grasp right hand grip with left hand and

fully depress throttle trigger to wide open position. Rapidly pull

recoil starter handle/rope (D) until engine res (or maximum ve

[5] pulls).

5. Choke

After engine res or ve (5) pulls, move choke lever back to “Run”

( ) position. Hold throttle trigger fully depressed and pull starter

handle/rope until engine starts and runs. Release throttle trigger

and allow unit to warm up at idle for several minutes.

NOTE

If engine does not start with choke in “Run” position after 5 pulls,

repeat instructions 2-5.

6. After engine warm up, gradually depress throttle trigger to increase

engine RPM to operating speed.

C

D

A

B

14

s t a r t I n G w a r m e n G I n e

The starting procedure is the same as Cold Start except DO NOT close

the choke, and do not depress throttle trigger to wide open position.

WARNING

The attachment should not move at idle, otherwise serious personal

injury may result.

NOTE

If attachment moves, readjust carburetor according to “Carburetor

Adjustment” instructions in this manual or see your ECHO Dealer.

1. Stop Switch

Move stop switch (A) away from the STOP position

2. Purge Bulb

Pump purge bulb (C) until fuel will be visible and ows freely in

the clear fuel tank return line. Pump bulb an additional 4 or 5

times.

3. Recoil Starter

Lay the unit on a at area and keep movable attachment parts clear

of all obstacles. Rapidly pull recoil starter handle/rope (D) until

engine res.

NOTE

If engine does not start after 5 pulls, use Cold Start Procedure.

s t o p p I n G e n G I n e

1. Throttle

Release throttle and allow engine to return to idle before shutting

off engine.

2. Stop Switch

Move stop switch button (A) backward to STOP position.

WARNING

If engine does not stop when stop switch is moved to STOP posi-

tion, close choke - COLD START position - to stall engine. Have

your ECHO dealer repair stop switch before using trimmer again.

A

C

D

A

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

15

m a I n t e n a n c e I n t e r v a l s

ma I n t e n a n c e

Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will help

your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take

your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF

or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed see your Echo dealer for

repairs.

s k I l l l e v e l

Level 1 = Easy to do. Common tools may be required.

Level 2 = Moderate difculty. Some specialized tools may be required.

ECHO offers REPOWER

TM

Maintenance Kits and Parts to make your maintenance job easier.

WARNING

Moving parts can amputate ngers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete

stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.

Wear gloves to protect hands from sharp edges and hot surfaces.

COMPONENT/SYSTEM

MAINTENANCE

PROCEDURE

SKILL

LEVEL

REQ'D

DAILY OR

BEFORE

USE

EVERY

REFUEL

3 MONTHS

OR 90

HOURS

YEARLY 600

HOURS

Air Filter Inspect/Clean 1

I / C * R*

Choke Shutter Inspect/Clean 1

I / C

Fuel Filter Inspect/Replace 1

I * I / R *

Fuel Cap Gasket Inspect/Replace 1

I * R *

Fuel System Inspect/Replace 1

I (3) I (3)

Spark Plug Inspect/Clean/Replace 1

I / C / R *

Cooling System Inspect/Clean 2

I / C

Muffler Spark Arrestor Inspect/Clean/Replace 2

I / C / R *

Cylinder Exhaust Port Inspect/Clean/Decarbon 2

I / C

Drive Shaft Inspect/Grease 2

I (1)

Gear Housing Grease 2

I (2)

Recoil Starter Rope Inspect/Clean 1

I / C *

Screws/Nuts/Bolts Inspect/Tighten/Replace 1

I *

* All recommendations to replace are based on the finding of damage or wear during inspection.

(2) Apply POWER BLENDX

TM

every 50 hours of use.

(3) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.

MAINTENANCE PROCEDURE LETTER CODES:

I = INSPECT, R = REPLACE, C = CLEAN

IMPORTANT NOTE

- Time intervals shown are maximum. Actual use and your experience will determine the

frequency of required maintenance.

MAINTENANCE PROCEDURE NOTES:

(1) Apply POWER BLENDX

TM

every 25 hours of use.

16

a I r f I l t e r

Level 1.

Tools required: 25 - 50 mm (1 - 2 in.) Cleaning Brush

Parts required: REPOWER

TM

AIR & FUEL FILTER KIT.

1. Close choke (Cold Start Position [ ]). This prevents dirt from

entering the carburetor throat when the air lter is removed. Brush

accumulated dirt from air cleaner area.

2. Remove air lter cover. Brush dirt from inside cover.

3. Remove air lter and lightly brush debris from lter. Replace lter

if it is damaged, fuel soaked, very dirty, or the rubber sealing edges

are deformed.

4. If lter can be reused, be certain it:

• Fits tightly in the air lter cavity.

• Is installed with the original side out.

5. Install air lter cover.

NOTE

Carburetor adjustment may be needed after air lter cleaning/re-

placement.

f u e l f I l t e r

Level 1.

Tools required: 200 - 250 mm (8 - 10 in.) length of wire with one

end bent into a hook, clean rag, funnel, and an

approved fuel container

Parts required: REPOWER

TM

AIR & FUEL FILTER KIT.

DANGER

Fuel is VERY ammable. Use extreme care when mixing, storing

or handling, or serious personal injury may result.

1. Use a clean rag to remove loose dirt from around fuel cap and

empty fuel tank.

2. Use the “fuel line hook” to pull the fuel line and lter from the

tank.

3. Remove the lter from the line and install the new lter.

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

17

s p a r k p l u G

Level 2.

Tools Required: Locking tool, wrench, feeler gauge, soft wire brush.

Parts Required: REPOWER

TM

Tune-Up Kit

IMPORTANT

Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) other-

wise severe engine damage may occur.

1. Remove spark plug and check for fouling, worn and rounded cen-

ter electrode.

2. Clean the plug or replace with a new one. DO NOT sand blast to

clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).

c o o l I n G s y s t e m

Level 2.

Tools required: T27 Torx L-Wrench, Cleaning Brush, 25 - 50 mm

(1 - 2 in.)

Parts Required: None.

IMPORTANT

To maintain proper engine operating temperatures, cooling air

must pass freely through the cylinder n area. This ow of air car-

ries combustion heat away from the engine.

Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air from reaching the

cylinder.

• Dust and grass build up on the outside of the cylinder. This build up

insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling ns is

considered “Normal Maintenance.” Any failure attributed to lack of

maintenance is not warranted.

1. Remove spark plug lead.

2. Remove air cleaner cover (A).

3. Remove 2 engine cover screws and engine cover (B).

0.65 mm

(0.026 in.)

A

B

18

C

D

E

IMPORTANT

DO NOT use a metal scraper to remove dirt from the cylinder ns.

4. Remove ignition wires from clip for cleaning.

5. Use brush to remove dirt from the cylinder ns.

6. Remove grass and leaves from the grid between the recoil starter

and fuel tank.

7. Assemble components in reverse order.

e x h a u s t s y s t e m

Spark Arrestor Screen

Level 2.

Tools Required: T27 Torx L-Wrench, Soft Metal Brush

Parts Required: Screen, Gasket

1. Remove spark plug lead from spark plug, and remove engine cover

(2 screws).

2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from

entering cylinder.

3. Remove spark arrestor screen cover (C), gasket (D), and screen

(E), from mufer body.

4. Clean carbon deposits from mufer components.

NOTE

When cleaning carbon deposit, be careful not to damage the cata-

lytic element inside mufer.

5. Replace screen if it is cracked, plugged, or has holes burned

through.

6. Install engine cover and attach spark plug lead.

Gr a s s Tr i m m e r

Op e r a T O r 's ma n u a l

19

c a r b u r e t o r a d j u s t m e n t

Engine Break-In

New engines must be operated a minimum duration of two tanks of fuel

break-in before carburetor adjustments can be made. During the break-

in period your engine performance will increase and exhaust emissions

will stabilize. Idle speed can be adjusted as required.

High Altitude Operation

This engine has been factory adjusted to maintain satisfactory starting,

emission, and durability performance up to 1,100 feet above sea level

(ASL) (96.0 kPa). To maintain proper engine operation and emission

compliance above 1,100 feet ASL the carburetor may need to be ad-

justed by an authorized ECHO service dealer.

IMPORTANT

If the engine is adjusted for operation above 1,100 feet ASL, the

carburetor must be re-adjusted when operating the engine below

1,100 feet ASL, otherwise severe engine damage may result.

Exhaust Port Cleaning

Level 2.

Tools required: Torx T27 L-Wrench, Wood or plastic scraper

Parts Required: As needed: Heat Shield

1. Remove spark plug lead from spark plug, and remove engine cover

(2 screws).

2. Place piston at top dead center. Remove mufer (A) and heat

shield (B).

3. Use a wood or plastic scraping tool to clean deposits from cylinder

exhaust port.

IMPORTANT

Never use a metal tool to scrape carbon from the exhaust port.

Do not scratch the cylinder or piston when cleaning the exhaust

port. Do not allow carbon particles to enter the cylinder.

4. Inspect heat shield, and replace if damaged.

5. Install heat shield and mufer.

6. Tighten mufer mounting bolts (or nuts) to 80-95 in•lbf

(90-110 kgf•cm).

7. Install engine cover and attach spark plug lead.

8. Start engine, and warm to operating temperature.

9. Stop engine, and re-tighten mounting bolts (or nuts) to specica-

tions.

A

B

20

Level 2.

Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017)

Parts required: None.

NOTE

Every unit is run at the factory and the carburetor is set in compli-

ance with emissions regulations. This carburetor does not have

acceleration and high speed adjustment needles.

1. Before adjusting the carburetor, clean or replace the air lter and

spark arrestor screen.

2. Start engine and run for several minutes to reach operating tem-

perature.

3. Check idle speed and reset if necessary. If a tachometer is avail-

able, idle speed screw (A) should be set to the specications found

on page 23 "Specications" of this manual. Turn idle screw (A)

clockwise to increase idle speed; counter clockwise to decrease

idle speed.

A

WARNING

When carburetor adjustment is completed, the cutting attachment

should not turn at idle, otherwise serious personal injury may

result.

l u b r I c a t I o n

Level 1.

Tools Required: 8mm Open end wrench, T27 Torx L-Wrench,

clean rag.

Parts Required: POWER BLENDX

TM

8 oz. (P/N 91014) or

Lithium Base Grease.

1. Remove plastic shield.

2. Loosen bearing housing locating screw (A), at the top of the hous-

ing, loosen mounting screw (B) and remove gear case from drive

housing.

3. Pull the exible drive shaft (C) from the drive housing, wipe clean

and recoat with a thin coating [1/2 oz. (15 ml)] of grease.

4. Slide the exible drive shaft back in the drive housing being care-

ful not to get dirt on the exible drive shaft.

5. Install the bearing housing and shield.

A

B

C

La page charge ...

Echo GT-225 Manuel utilisateur

Echo GT-225 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents