Echo SRM - 230S Manuel utilisateur

WARNING

Read rules for safe operation and instructions carefully. ECHO provides an

Operator's Manual and a Safety Manual. Both must be read and understood for

proper and safe operation.

Grass Trimmer/Brush Cutter

Operator's Manual

MODEL SRM - 230

SRM - 230S

X7532098302

X753002992

12/08

2

INTRODUCTION

Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job

dependability. Read and understand this manual and the SAFETY MANUAL you found in the same package. You will

find both easy to use and full of helpful operating tips and SAFETY messages.

THE OPERATOR'S MANUAL

Read and understand this manual before operation. Keep it in a safe

place for future reference. It contains specifications and information for

operation, starting, stopping, maintenance, storage and assembly

specific to this product.

THE SAFETY MANUAL

Read and understand this manual before operation. Keep it in a safe

place for future reference. It explains possible hazards involved with the

use of Grass Trimmers and Brush Cutters and what measures you

should take to make their use safer.

TABLE OF CONTENTS

Introduction ........................................................................ 2

- The Operator's Manual .............................................. 2

- The Safety manual ...................................................... 2

Safety .................................................................................. 3

- Manual Safety Symbols and Important Information . 3

- International Symbols ................................................. 3

- Personal Condition and Safety Equipment ................... 4

- Equipment .................................................................... 6

Emission Control .................................................................. 6

Description .......................................................................... 7

Contents .............................................................................. 9

Assembly ............................................................................. 9

- Plastic Shield Installation ............................................. 9

- Nylon Line Head Installation ..................................... 10

- To Advance Trimmer Line ........................................ 10

- Nylon Line Replacement ........................................... 10

- Remove Nylon Line Head ......................................... 10

- Front Handle Adjustment ........................................... 11

Operation ........................................................................... 11

- Operation with Blades ............................................... 11

- Fuel ........................................................................... 14

- Starting Cold Engine .................................................. 16

- Starting Warm Engine ............................................... 17

- Stopping Engine ......................................................... 17

Maintenance ...................................................................... 18

- Skill Levels ................................................................ 18

- Maintenance Intervals ............................................... 18

- Air Filter .................................................................... 19

- Fuel Filter .................................................................. 19

- Spark Plug ................................................................. 20

- Cooling System .......................................................... 20

- Exhaust System ......................................................... 21

- Carburetor Adjustment Emission ............................... 23

- Lubrication ................................................................ 24

- Nylon Line Replacement ........................................... 25

- Sharpening Metal Blades ........................................... 26

Troubleshooting ................................................................. 27

Storage .............................................................................. 28

Specifications .................................................................... 29

Servicing Information ........................................................ 32

- Parts/Serial Number .................................................. 32

- Service ...................................................................... 32

- ECHO Consumer Product Support ............................ 32

- Warranty Card .......................................................... 32

- Additional or Replacement Manuals .......................... 32

Specifications, descriptions and illustrative material in

this literature are as accurate as known at the time of

publication, but are subject to change without notice.

Illustrations may include optional equipment and

accessories, and may not include all standard equipment.

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

3

INTERNATIONAL SYMBOLS

Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages

preceded by symbols or key words. The following is an explanation of those symbols and key words and what they

mean to you.

SAFETY

MANUAL

SAFETY SYMBOLS AND IMPORTANT INFORMATION

Hot

Surface

Carburetor

Adjustment

- Idle speed

Carburetor

Adjustment

- High speed

mixture

DESCRIPTION

SYMBOLSYMBOL

"WARNING, SEE

OPERATOR'S

MANUAL

Wear eye, ear

and head

protection

Emergency

Stop

Fuel and oil

mixture

Finger Severing

Carburetor

Adjustment

- Low speed

mixture

Primer

Bulb

Ignition

ON/

OFF

Wear hand and

foot protection

Safety/Alert

Keep bystanders and helpers

away 15 m (50 ft.).

DO NOT smoke

near fuel.

DO NOT allow

flames or sparks

near fuel.

DESCRIPTION

SYMBOL DESCRIPTION

SYMBOL

DESCRIPTION

Choke Control

"Cold Start"

Position

(Choke Closed)

Choke Control

"Run"

Position

(Choke Open)

Do not use

blades. String

line only

WARNING

The safety alert symbol accompanied by the

word “WARNING” calls attention to an act or

condition which CAN lead to serious personal

injury or death if not avoided.

CAUTION

The safety alert symbol accompanied by the

word “CAUTION” calls attention to an act or

condition which may lead to minor or moderate

personal injury if not avoided.

DANGER

The safety alert symbol accompanied by the

word “DANGER” calls attention to an act or

condition which WILL lead to serious personal

injury or death if not avoided.

CIRCLE AND SLASH SYMBOL

This symbol means the specific action

shown is prohibited. Ignoring these

prohibitions can result in serious or fatal

injury.

NOTE

This enclosed message provides tips for use, care

and maintenance of the unit.

IMPORTANT

The enclosed message provides information neces-

sary for the protection of the unit.

4

Physical Condition

Your judgment and physical dexterity may not be good:

• if you are tired or sick,

• if you are taking medication,

• if you have taken alcohol or drugs.

Operate unit only if you are physically and mentally

well.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE

requirements whenever you operate the unit.

Hand Protection

Wear no-slip, heavy-duty work gloves to improve your

grip on the handle. Gloves also reduce the transmission

of machine vibration to your hands.

Hearing Protection

ECHO recommends wearing hearing protection when-

ever unit is used.

Extended Operation/Extreme Conditions

It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be

brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning

sensations, followed by loss of color and numbness in the fingers. The following precautions are strongly recom-

mended, because the minimum exposure, which might trigger the ailment, is unknown.

• Keep your body warm, especially the head, neck, feet, ankles, hands,

and wrists.

• Maintain good blood circulation by performing vigorous arm exer-

cises during frequent work breaks, and also by not smoking.

• Limit the hours of operation. Try to fill each day with jobs where

operating the unit or other hand-held power equipment is not

required.

• If you experience discomfort, redness, and swelling of the fingers

followed by whitening and loss of feeling, consult your physician

before further exposing yourself to cold and vibration.

PERSONAL CONDITION AND SAFETY EQUIPMENT

WARNING

Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions

are not followed. Proper clothing and safety gear must be worn when operating unit.

Proper Clothing

Wear snug fitting, durable clothing;

• Pants should have long legs, shirts with long sleeves.

• DO NOT WEAR SHORTS,

• DO NOT WEAR TIES, SCARFS, JEWELRY.

Wear protective hair covering to contain long hair.

Wear sturdy work shoes with nonskid soles;

• DO NOT WEAR OPEN TOED SHOES,

• DO NOT OPERATE UNIT BAREFOOTED.

Keep long hair away from engine and air intake. Retain

hair with cap or net.

Hot Humid Weather

Heavy protective clothing can increase operator fatigue

which may lead to heat stroke. Schedule heavy work for

early morning or late afternoon hours when temperatures

are cooler.

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

5

DANGER

Do not operate this product indoors or in inadequately ventilated

areas. Engine exhaust contains poisonous emissions and can

cause serious injury or death.

Read the Manuals

• Provide all users of this equipment with the Operator’s Manual and

Safety Manual for instructions on Safe Operation.

Clear the Work Area

• Spectators and fellow workers must be warned, and children and

animals prevented from coming nearer than 15 m (50 ft.) while the unit

is in use.

Keep a Firm Grip

• Hold the front and rear handles with both hands, with thumbs and

fingers encircling the handles.

Keep a Solid Stance

• Maintain footing and balance at all times. Do not stand on slippery,

uneven or unstable surfaces. Do not work in odd positions or on

ladders. Do not over reach.

Avoid Hot Surfaces

• Keep exhaust area clear of flammable debris. Avoid contact during

and immediately after operation.

Repetitive Stress Injuries

It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness,

swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high

risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which

could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged

exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.

To reduce the risk of RSI/CTS, do the following:

• Avoid using your wrist in a bent, extended, or twisted position.

Instead try to maintain a straight wrist position. Also, when grasping,

use your whole hand, not just the thumb and index finger.

• Take periodic breaks to minimize repetition and rest your hands.

• Reduce the speed and force with which you do the repetitive move-

ment.

• Do exercise to strengthen the hand and arm muscles.

• Immediately stop using all power equipment and consult a doctor if

you feel tingling, numbness, or pain in the fingers, hands, wrists, or

arms. The sooner RSI/CTS is diagnosed, the more likely permanent

nerve and muscle damage can be prevented.

6

EQUIPMENT

WARNING

Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment

combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which

have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and

safety manual.

• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.

• Inspect fuel lines, tank, and area around carburetor for fuel leaks. DO NOT operate unit if leaks are found.

• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is damaged or

missing.

• Check that the cutting attachment is firmly attached and in safe operating condition.

• Check that front loop handle and shoulder strap/ or shoulder/waist harness are adjusted for safe, comfortable

operation. See Assembly Section for proper adjustment.

An Emission Control Label is located on the engine. (This is

an EXAMPLE ONLY, information on label varies by engine

FAMILY).

WARNING

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings.

• ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop

before removing obstructions, clearing debris, or servicing unit.

• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.

• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.

WARNING

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found,

do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an autho-

rized servicing dealer before using.

EMISSION CONTROL (EXHAUST & EVAPORATIVE)

EPA Phase 2

The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel

tank the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be appli-

cable to California models only.

PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)

The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine

emissions output meets applicable emissions regulations, provided that approved maintenance procedures are

followed as listed in the Maintenance Section of this manual.

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY: 8EHXS.0234KA DISPLACEMENT: 22.8 cc

EMISSION COMPLIANCE PERIOD : 300 HRS.

THIS ENGINE MEETS U.S. EPA PHASE 2 EMISSION

REGULATIONS FOR SMALL NONROAD ENGINES. REFER TO

OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS

AND ADJUSTMENTS.

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

7

11

13

14

15

16

17

18

12

19

1

2

3

4

5

6

7

8

9

10

P/N X505002310

Hot Decal (near muffler)

P/N 89016054130

DESCRIPTION

Locate these safety decals on your unit. Make sure the decals are legible and that you understand and follow the

instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDER-

ING instructions for specific information.

P/N X505001930

P/N 89016054130

Shaft Decal

P/N X505001930

8

1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter.

2. GRIP - Rear (right hand) handle.

3. THROTTLE TRIGGER LOCKOUT - This lever must be held during starting. Operation of the throttle trigger is

prevented unless throttle trigger lockout lever is engaged.

4. STOP SWITCH - "SLIDE SWITCH" mounted on top of the Throttle Trigger Housing. Move switch FORWARD to

RUN, BACK to STOP.

5. FRONT HANDLE - The Front (loop) handle is loosely assembled to the Drive Shaft assembly and must be posi-

tioned for proper control and operator comfort.

6. DRIVE SHAFT ASSEMBLY - Includes the Rear (right hand) Handle assembly, Gear Housing assembly, Front (loop,

left hand) Handle assembly, steel drive shaft and Safety Decal.

7. NYLON CUTTER HEAD - Contains replaceable nylon trimming line that advances when the trimmer head is tapped

against the ground while the head is turning at normal operating speed.

8. CUT-OFF KNIFE - Automatically trims line to the correct length: 5" after head is tapped on the ground. If trimmer is

operated without a cut-off knife the line will become too long, the engine will overheat and engine damage may occur.

9. PLASTIC DEBRIS SHIELD ASSEMBLY - Included in plastic bag (co-pack). MUST be installed on unit before use,

see Assembly Instructions. Shield assembly includes the Cut-Off Knife. Mounts on the Gear Housing Assembly just

above the cutting attachment. Helps protect the operator by deflecting debris produced during the trimming opera-

tion. This shield must be replaced with the steel shield for blade use.

10. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradually

for best operating technique.

11. SPARK PLUG - Provides spark to ignite fuel mixture.

12. TOP GUARD - Protects arm from the hot engine.

13. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise

and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep

exhaust area clear of flammable debris.

14. FUEL TANK - Contains fuel and fuel filter.

15. RECOIL STARTER HANDLE - Pull handle slowly until starter engages, then quickly and firmly. When engine

starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.

16. FUEL TANK CAP - Covers and seals fuel tank opening.

17. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the

carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge bulb

an additional 4 or 5 times.

18. AIR CLEANER - Contains replaceable filter element.

19. CHOKE - The choke control is located on the top of the air filter case. Move choke lever to "Cold Start" ( ) to

close choke for cold start. Move choke lever to "Run" ( ) position to open choke.

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

9

CONTENTS

The ECHO product you purchased has been partially assembled for your convenience. Due to packaging restrictions,

installation of the plastic debris shield, nylon line head, and positioning of the front handle are necessary.

After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing

parts. Use the contents list to check for missing parts.

* Some Echo units may be factory pre-assembled. The nylon line head, plastic debris shield, and mounting hardware

shown in the contents list are pre-assembled to the unit. Assembly tools are not supplied with these units. The front

handle may need to be re-positioned for comfortable operation.

______1 - Power Head / Drive Shaft Assembly

______1 - Operator's Manual

______1 - Safety Manual

______1 - Warranty Registration Card

______1 - Limited Warranty Statement

______1 - Safety Glasses

______1 - Echo Power BlendX

TM

2-stroke oil sample

* ___ 1 - Nylon Trimmer Head

* ___ 1 - T-wrench 17x19, P/N 89541008030

* ___ 1 - Locking tool, P/N 89751801131

* ___ 1 - Plastic shield

* ___ 1 - Shield plate

* ___ 3 - 5mm x 16mm screws (shield mtg.)

ASSEMBLY

Tools Required: Screwdriver, Head Locking Tool

Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 16mm

screws, Nylon Line Head, Front Handle Assembly

PLASTIC SHIELD INSTALLATION

(For Nylon Line Operation)

NOTE

The plastic shield is for use with the Nylon Line Head only.

Install Metal Shield when using plastic or metal blades.

1. Remove plastic sleeve and upper plate (A) from PTO shaft.

2. Install the shield on the bottom of the bearing housing flange.

3. Place shield plate (B) on shield, align holes and install three (3)

5x16 mm screws.

4. Install upper plate (A).

A

B

C

10

A

C

NYLON LINE HEAD INSTALLATION

Tools Required: Head Locking Tool.

Parts Required: Nylon Line Head.

CAUTION

Wear Gloves or personal injury may result:

• Cutoff knife is sharp.

• Gearcase and surrounding area may be hot.

1. Be sure adapter plate (C) remains on PTO shaft.

2. Align locking hole in upper plate with notch in edge of gear

housing and insert head locking tool (D).

3. Thread line head (E) onto shaft by turning it counter-clockwise

until head is tight against adapter plate (C).

4. Remove locking tool (D).

D

E

TO ADVANCE TRIMMER LINE

Tip:

To advance trimmer line, tap trimmer head against the ground

while the head is turning at normal operating speed.

NYLON LINE REPLACEMENT

See Maintenance Section for nylon line replacement.

REMOVE NYLON LINE HEAD

NOTE

Do not disassemble nylon line head.

1. Align locking hole in upper plate with notch in edge of gear

housing and insert head locking tool (D).

2. Remove line head (E) by turning it clockwise until head is

completely off of shaft.

3. Remove locking tool (D).

D

E

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

11

MIN

SPACING

FRONT HANDLE ADJUSTMENT

NOTE

Label shows minimum spacing for front handle location.

1. Position front handle for comfortable operation and secure screws.

OPERATION

WARNING

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete

stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing

service. Wear gloves to protect hands from sharp edges and hot surfaces.

WARNING

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconscious-

ness, serious injury, or death. Exhaust can cause serious burns. ALWAYS blow exhaust away from your face and

body.

12

SRM/PAS/SB BLADE SET-UP GUIDE*

TO USE

THESE BLADES

Pro Maxi-Cut

Grass/Weed

Plastic Cutters

Rigid Plastic

Tri-Cut

Grass/Weed Blade

Metal

Tri-Cut/8 Tooth

Grass/Weed Blade

Metal 80T Brush Blade

Metal 22T Clearing Saw Blade

Handle

Loop Handle, w/or

w/o Barrier Bar

Loop Handle

w/Barrier Bar,

or U-Handle

Loop Handle

w/Barrier Bar,

or U-Handle

U-Handle

Debris Shield Metal Shield Metal Shield Metal Shield Metal Shield

Harness Shoulder Harness Shoulder Harness Shoulder Harness Shoulder Harness****

Upper Plate &

Flat Washer

Upper Plate

& Glide Cup

Upper/Lower

Blade Plates**

Upper/Lower

Blade Plates**

Hex Nut Hex Nut Hex Nut Hex Nut

You

must

install

these

parts!

Blade

Mounting

Hardware

New Cotter Pin*** New Cotter Pin*** New Cotter Pin*** New Cotter Pin***

* WARNING! DO NOT INSTALL BLADES ON GT (CURVED SHAFT) MODEL TRIMMERS

** Arbor diameter of Upper Blade Plate must match arbor diameter of metal blades.

*** New cotter pin required each time blade is installed.

**** Brushcutters over 16.5 lbs (7.5 kg) dry weight (weight w/o fuel) require a double shoulder harness

A

B

Grass/Weed Blades Require:

Install Blade Conversion Kit, Includes metal shield

(A), barrier bar (B), and shoulder harness (C).

C

NOTE

The Barrier Bar is used to restrict rearward movement of the unit. The Barrier Bar is NOT A HANDLE and should

not be gripped when using or carrying the unit.

C

A

D

Brush/Clearing Blades Require:

Install U-Handle / Blade Conversion Kit, - Includes

metal shield (A), shoulder harness with hip pad (C),

and U-Handles (D).

OPERATION WITH BLADES

Preparing the Trimmer/Brush Cutter for Blade Use

WARNING

Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield, handle, and harness

can result in serious personal injury. Follow installation instructions included in optional kits.

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

13

Choosing the Correct Blade

WARNING

The type of Blade used MUST be matched to the type and size of material cut. An improper or dull blade can

cause serious personal injury. Blades MUST be sharp. Dull blades increase the chance of kick-out and injury to

yourself and bystanders.

Plastic/Nylon Blades may be used where ever the nylon line head

is used. DO NOT use this blade for heavy weeds or brush!

8 Tooth Weed/Grass Blade (P/N 69600120331) is designed for grass,

garden debris and thick weeds. DO NOT use this blade for brush or

heavy woody growth, 19 mm (3/4 in.) diameter or larger.

80 Tooth Brush Blade (P/N 69500120331) is designed for cutting

brush and woody growth up to 13 mm (1/2 in.) diameter.

22 Tooth Clearing Blade (99944200130) is designed for dense

thickets and saplings up to 64 mm (2-1/2 in.) diameter.

Use Shoulder/Waist Harness (P/N 99944200200) Use of the

Shoulder/Waist Harness is recommended for ALL Trimmer/Brush

Cutter use. The Shoulder/Waist Harness suspends the trimmer from

the operator's shoulder and reduces operator fatigue.

The restrictive harness enhances operator safety by reducing the

possibility of blade contact with the operator's hands and feet.

14

FUEL

NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting,

poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the

Storage section of this manual.

WARNING

Alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any fuels not meeting above requirements

are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance

problems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited

to, improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets,

carburetors and other engine components.

Fuel Requirements

Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to

10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is

NOT approved.

Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must

be used. Echo brand premium Power Blend X

TM

Universal 2-Stroke Oil meets these standards. Engine problems due to

inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD certified oil, such

as Echo premium Power Blend X

TM

, will void the two-stroke engine warranty.

IMPORTANT

Echo premium Power BlendX

TM

Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo

engines sold in the past regardless of ratio specified in those manuals.

Handling Fuel

DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may

result.

• Use an approved fuel container.

• DO NOT smoke near fuel.

• DO NOT allow flames or sparks near fuel.

• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT or RUNNING!

• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.

• DO NOT overfill fuel tank. Wipe up spills immediately.

• Securely tighten fuel tank cap and close fuel container after refueling.

• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.

• Move at least 3m (10 ft.) from refueling location before starting the engine.

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

15

Mixing Instructions

1. Fill an approved fuel container with half of the required amount of

gasoline.

2. Add the proper amount of 2-stroke oil to gasoline.

3. Close container and shake to mix oil with gasoline.

4. Add remaining gasoline, close fuel container, and remix.

IMPORTANT

Spilled fuel is a leading cause of hydrocarbon emissions. Some

states may require the use of automatic fuel shut-off containers to

reduce fuel spillage.

After use

• DO NOT store a unit with fuel in its tank. Leaks can occur. Return

unused fuel to an approved fuel storage container.

Storage - Fuel storage laws vary by locality. Contact your local

government for the laws affecting your area. As a precaution, store fuel

in an approved, airtight container. Store in a well-ventilated, unoccu-

pied building, away from sparks and flames.

IMPORTANT

Stored fuel ages. Do not mix more fuel than you expect to use in

thirty (30) days, ninety (90) days when a fuel stabilizer is added.

IMPORTANT

Stored two-stroke fuel may separate. ALWAYS shake fuel con-

tainer thoroughly before each use.

16

STARTING COLD ENGINE

WARNING

The attachment will operate immediately when the engine starts

and could result in loss of control and possible serious injury.

Keep movable parts of the attachment off the ground and away

from objects that could become entangled or thrown.

1. Stop Switch

Move stop switch button (A) forward away from the STOP

position.

2. Choke

Move choke lever (B) to Cold Start Position ( ).

3. Purge Bulb

Pump purge bulb (C) until fuel is visible and flows freely in the clear

fuel tank return line. Pump bulb an additional 4 or 5 times.

4. Recoil Starter

Lay the unit on a flat area and keep movable attachment parts clear

of all obstacles. Firmly grasp right hand grip and throttle trigger

lockout with left hand and fully depress throttle trigger to wide

open position. Rapidly pull recoil starter handle/rope (D) until

engine fires (or maximum five [5] pulls).

5. Choke

After engine fires (or 5 pulls), move choke lever back to Run ( )

position. Hold throttle trigger and throttle trigger lockout fully

depressed, and pull recoil starter starter handle/rope until engine

starts and runs. Release throttle trigger, and allow unit to warm up

at idle for several minutes.

NOTE

If engine does not start with choke in “Run” position after 5 pulls,

repeat instructions 4 and 5.

6. Throttle Trigger

After engine warm-up, gradually depress throttle trigger to increase

engine RPM to operating speed.

B

C

D

A

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

17

STARTING WARM ENGINE

The starting procedure is the same as Cold Start except DO NOT close

the choke, and do not hold throttle trigger fully depressed.

WARNING

The attachment should not move at idle, otherwise serious

personal injury may result.

NOTE

If attachment moves, readjust carburetor according to “Carburetor

Adjustment” instructions in this manual or see your ECHO Dealer.

1. Stop Switch

Move stop switch button (A) away from the STOP position.

2. Purge Bulb

Pump purge bulb (C) until fuel is visible and flows freely in the clear

fuel tank return line. Pump bulb an additional 4 or 5 times.

3. Recoil Starter

Lay the unit on a flat area and keep movable attachment parts clear

of all obstacles. Rapidly pull the recoil starter handle (D) until the

engine fires.

NOTE

If engine does not start after 5 pulls, use Cold Start Procedure.

STOPPING ENGINE

1. Release Throttle.

Allow engine to return to idle before shutting off engine.

2. Stop Switch

Move stop switch button (A) backward to STOP position.

WARNING

If engine does not stop when stop switch is moved to STOP

position, close choke - COLD START position - to stall engine.

Have your ECHO dealer repair stop switch before using trimmer

again.

D

C

A

18

WARNING

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all

openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete

stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing

service. Wear gloves to protect hands from sharp edges and hot surfaces.

MAINTENANCE

INTERVALS

Your ECHO trimmer is designed to provide many hours of trouble free service. Regular scheduled maintenance will

help your trimmer achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to

take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOUR-

SELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO

Dealer for repairs.

SKILL LEVELS

Level 1 = Easy to do. Common tools may be required.

Level 2 = Moderate difficulty. Some specialized tools may be required.

ECHO offers REPOWER

TM

Maintenance Kits and Parts to make your maintenance job easier. Below each task

heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.

COMPONENT/

SYSTEM

MAINTENANCE

PROCEDURE

REQ'D

SKILL

LEVEL

DAILY OR

BEFORE

USE

EVERY

REFUEL

3 MONTHS

OR 90

HOURS

YEARLY

600 HOURS

Air Filter Inspect/Clean

1 I / C * R *

Choke Shutter Inspect/Clean

1 I / C

Fuel Filter Inspect/Replace

1 I * I / R *

Fuel Cap Gasket Inspect/Replace 1

I *

Fuel System Inspect/Replace

1 I (3) * I (3) *

Spark Plug Inspect/Clean

1 I / C / R *

Cooling System Inspect/Clean

2 I / C

Muffler Spark Arrestor Inspect/Clean/Replace

2 I / C / R *

Cylinder Exhaust Port Inspect/Clean/Decarbon

2 I / C

Drive Shaft (Flex Cable

Models)

Grease

2 I (1)

Gear Housing Grease

2 I (2)

Recoil Starter Rope Inspect/Clean

1 I / C *

Screws/Nuts/Bolts Inspect/Tighten/Replace

1 I *

MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN

IMPORTANT NOTE

- Time intervals shown are maximum. Actual use and your experience will determine the

frequency of required maintenance.

MAINTENANCE PROCEDURE NOTES:

(1) Apply POWER BLENDX

TM

grease every 25 hours of use.

(2) Apply POWER BLENDX

TM

grease every 50 hours of use.

(3) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.

* Replacement is recommended based on the finding of damage or wear during inspection.

GRASS TRIMMER/BRUSH CUTTER

OPERATOR'S MANUAL

19

AIR FILTER

Level 1.

Tools Required: Cleaning brush 25 or 50 mm (1 or 2 in.)

Parts Required: REPOWER

TM

AIR & FUEL FILTER KIT.

1. Close choke (Cold Start Position [ ]). This prevents dirt from

entering the carburetor throat when the air filter is removed. Brush

accumulated dirt from air cleaner area.

2. Remove air filter cover. Brush dirt from inside cover.

3. Remove air filter and lightly brush debris from filter. Replace filter if

it is damaged, fuel soaked, very dirty, or the rubber sealing edges

are deformed.

4. If filter can be reused, be certain it:

• Fits tightly in the air filter cavity.

• Is installed with the original side out.

5. Install air filter cover.

FUEL FILTER

Level 1.

Tools Required: 200-250 mm (8 -10 in.) length of wire with one end bent

into a hook, clean rag, funnel, and an approved fuel

container.

Parts Required: REPOWER

TM

AIR & FUEL FILTER KIT.

DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing

or handling.

1. Use a clean rag to remove loose dirt from around fuel cap and

empty fuel tank.

2. Use the “fuel line hook” to pull the fuel line and filter from the

tank.

3. Remove the filter from the line and install the new filter.

20

SPARK PLUG

Level 2.

Tools Required: T-Wrench, feeler gauge, soft metal brush.

Parts Required: REPOWER

TM

Tune-Up Kit

IMPORTANT

Use only NGK BPM-8Y spark plug (BPMR-8Y in Canada) otherwise

severe engine damage may occur.

1. Remove spark plug and check for fouling, worn and rounded

center electrode.

2. Clean the plug or replace with a new one. DO NOT sand blast to

clean. Remaining sand will damage engine.

3. Adjust spark plug gap by bending outer electrode.

4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).

COOLING SYSTEM

Level 2.

Tools Required: 4 mm Hex Wrench, cleaning brush, 25 or 50 mm

(1 or 2 in.)

Parts Required: None if you are careful.

IMPORTANT

To maintain proper engine operating temperatures, cooling air

must pass freely through the cylinder fin area. This flow of air

carries combustion heat away from the engine.

Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air from reaching the

cylinder.

• Dust and grass build up on the outside of the cylinder. This build up

insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is

considered “Normal Maintenance.” Any failure attributed to lack of

maintenance is not warranted.

0.65 mm

(0.026 in.)

La page charge ...

Echo SRM - 230S Manuel utilisateur

Ce manuel convient également à

Echo SRM - 230S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents