Chief PACCS1 Guide d'installation

Marque: Chief

Modèle: PACCS1

Catégorie: Mur

Taper: Guide d'installation

INSTALLATION INSTRUCTIONS

Large Shelf Accessory

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

PACCS1

PACCS1 Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and

subsidiaries (collectively "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component. The wall to which the mount is being attached

may have a maximum drywall thickness of 5/8" (1.6cm).

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components located on the PACCS1 does not exceed

15 lbs (6.8 kg). Use with products heavier than the maximum

weight indicated may result in collapse of the mount and its

accessories causing possible injury.

DIMENSIONS

14.00

7.87

15.50

25.51 EXTENDED

24.64 COLLAPSED

(1.00)

17.51 EXTENDED

15.64 COLLAPSED

MOUNTING HOLES FOR

OPTIONAL 200X200

VESA PATTERN

APPROXIMATE

CENTER OF SCREEN

1.06

ADDED TO

OVERALL

MOUNT DEPTH

1.62

12.88 EXTENDED

11.35 COLLAPSED

18.31

MEASUREMENTS IN INCHES

Installation Instructions PACCS1

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

PACCS1 Installation Instructions

TOOLS REQUIRED FOR INSTALLATION

PARTS

1/8"

(included)

1/4"

C (1)

[Shelf]

A (1)

[Shelf Bracket]

B (1)

[Adjustment Bracket]

D (1)

[Right Upright]

E (1)

[Left Upright]

F (4)

[Mounting Button]

G (4)

[Rubber Bumper]

H (6)

[Cable Tie]

J (2)

1" x 1"

[Hook & Loop]

K (1)

1/8"

M (2)

1/4-20

N (4)

1/4-20 x 5/8" P (2)

1/4-20 x 5/8"

Q (2)

10-24 x 1/2"

R (4)

10-24 x 7/8"

L (6)

10-24

S (2)

1/4"

Installation Instructions PACCS1

ASSEMBLY AND INSTALLATION

NOTE: The PACCS1 is designed to accommodate both

200mm x 200mm and 14" x 14" Q-latch mounting

systems. If a 200mm x 200mm pattern is required, use

the inner mounting holes on the shelf bracket (A) when

installing the uprights (D and E). (See Figure 2)

NOTE: The 14" x 14" display mounting pattern is NOT identical

to a 400 x 400 VESA display mounting pattern.

IMPORTANT ! : If installing the PACCS1 with the PACLR1

the top mounting flange on the PACCS1 must hang over the top

of the lower speaker rail on the PACLR1 when installed. (See

Figure 3)

Assemble PACCS1

1. Install top two mounting buttons (F) to uprights (D and E)

using two 10-24 x 7/8" button head cap screws (R) and two

10-24 lock nuts (L). (See Figure 1)

Figure 1

2. Assemble two lower mounting buttons (F) to uprights (D and

E) and shelf bracket (A) using two 10-24 x 7/8" button head

cap screws (R) and two 10-24 lock nuts (L).

3. Complete attachment of uprights (D and E) to shelf bracket

(A) using two 10-24 x 1/2" button head cap screws (Q) and

two 10-24 lock nuts (L). (See Figure 2)

Figure 2

4. Assemble adjustment bracket (B) to shelf bracket (A) using

four 1/4-20 x 5/8" button head cap screws (N) -- two on each

side of adjustment bracket. (See Figure 3)

Figure 3

5. Lower shelf (C) to the assembly. (See Figure 4)

6. Attach shelf (C) using two 1/4-20 x 5/8" round head carriage

bolts (P), two 1/4" flat washers (S) and two 1/4-20 nylon lock

nuts (M). (See Figure 4)

(R) x 2

(F) x 2

(L) x 2

(E)

(D)

(E)

(A)

(Q) x 2

(F) x 2

(L) x 2

(R) x 2

Attachment for

200mm x 200mm

(N) x 4

(B)

(A)

PACLR1

PACCS1 Installation Instructions

Figure 4

Installing PACCS1 to Mount and Display to PACCS1

1. Install PACCS1 to mount following the installation

instructions provided with the mount. (See Figure 5)

Figure 5

2. Verify latching flag is in the OPEN position. (See Figure 5)

and (See Figure 6)

3. Align four mounting buttons on display with four teardrop

mounting holes in accessory. (See Figure 5) and (See

Figure 6)

4. Slide mounting buttons into teardrop mounting holes and

lower display until recessed area of mounting buttons is

seated in lower area of teardrop mounting holes. (See

Figure 5) and (See Figure 6)

WARNING: IMPROPER INSTALLATION CAN LEAD TO

DISPLAY FALLING CAUSING SEVERE PERSONAL

INJURY OR DAMAGE TO EQUIPMENT. Make sure ALL

mounting buttons are properly seated in lower area of four

teardrop mounting holes.

5. Move latching flag to CLOSED position to secure display on

PACCS1. (See Figure 6)

NOTE: A padlock or similar device may be used to provide

additional security.

Figure 6

Adjustments

The PACCS1 allows for vertical adjustment of the shelf to

provide a flush installation against the bottom of the display.

To adjust shelf vertical position:

1. Loosen two button head cap screws securing adjustment

bracket to shelf bracket using 1/8" hex wrench (K). (See

Figure 7)

(C)

(S) x 2

(M) x 2

(P) x 2

Latching Flag

Open

Display

Open Flag

Close Flag

Latching Flag

Optional locking device placed here

Installation Instructions PACCS1

2. Reposition shelf up or down to desired position. (See

Figure 7)

3. Tighten two button head cap screws securing adjustment

bracket to shelf bracket using 1/8" hex wrench (K). (See

Figure 7)

Figure 7

To adjust shelf horizontal position:

1. Loosen two round head carriage bolts securing shelf. (See

Figure 8)

Figure 8

2. Reposition shelf in or out to desired position. (See Figure 8)

3. Tighten two round head carriage bolts securing shelf. (See

Figure 8)

Cable Management

Route cables and wires to display using cable ties (H) as

necessary, and following manufacturers installation instructions.

Installing Equipment on Shelf

1. If necessary, place rubber bumpers (G) or hook and loop

squares (J) on shelf to help hold equipment in place.

1. Place equipment on shelf.

NOTE: A strap, such as the PAC103 (not included), may also

be used to hold the equipment in place on the shelf.

2. OPTIONAL: Thread optional strap (PAC103) through slots

in shelf. (See Figure 9)

3. Complete installation of strap following instructions included

with the strap kit.

Figure 9

Shelf

Completely

Retracted

Shelf

Completely

Extended

Display

PACCS1

shelf

PACCS1 Installation Instructions

USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378

P 800.582.6480 / 952.894.6280

F 877.894.6918 / 952.894.6918

Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands

P +31 (0)40 2668620

F +31 (0)40 2668615

Asia Pacific A Office No. 1 on 12/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P 852 2145 4099

F 852 2145 4477

Chief Manufacturing, a products division

of Milestone AV Technologies

8800-002050 Rev03

2011 Milestone AV Technologies, a

Duchossois Group Company

www.chiefmfg.com

01/11

Chief PACCS1 Guide d'installation

Marque: Chief

Modèle: PACCS1

Catégorie: Mur

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Chief PACCS1 Installation guide

Documents connexes

Autres documents

Chief Manufacturing Indoor Furnishings JWP Manuel utilisateur