Sauder Corner Entertainment Credenza 403818 Mode d'emploi

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-28

Français pg 29-32

Español pg 33-36

Lot # 375372 07/06/15

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Corner Entertainment Credenza

Orchard Hills Collection | 403818

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

Smart stand

for the idiot box.

Table of Contents Assembly Tools Required

3

4-5

6-28

29-32

33-36

37-38

39

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or

death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.

• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!

• This Sauder unit is designed for use with televisions weighing less than 135 pounds. Never use with a TV that weighs more.

• The size of the television, front-to-back and side-to-side, must ﬁ t within the space deﬁ ned in the diagram.

• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)

• Never allow the sides of the TV to extend past the side edges of the TV support surface.

• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.

• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.

WARNING

!

135 lbs.

18-7/8"

60-1/8"

403818 www.sauder.com/servicesPage 2

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

A RIGHT END (1)

B LEFT END (1)

C UPRIGHT (1)

D TOP (1)

E SHELF (2)

F BOTTOM (1)

G BRACE (2)

H BACK (1)

I RIGHT BACK (1)

J LEFT BACK (1)

K ADJUSTABLE SHELF (2)

L SMALL ADJUSTABLE SHELF (2)

M RIGHT DRAWER FRONT (1)

N LEFT DRAWER FRONT (1)

S SHELF MOLDING (1)

T BASE (1)

U RIGHT BASE (1)

V LEFT BASE (1)

W BACK MOLDING (2)

X LONG MOLDING (2)

Y SHORT MOLDING (2)

Z MOLDING (4)

D65 DRAWER BACK (2)

D107 RIGHT DRAWER SIDE (2)

D108 LEFT DRAWER SIDE (2)

D962 DRAWER BOTTOM (2)

403818www.sauder.com/services

Page 3

M

N

D107D65

D962

D108

D107

D65

D962

D108

A

B

C

D

E

F

G

H

I

J

K

L

S

T

U

V

W

X

Y

Z

X

Z

G

K

E

L

W

Y

Hardware Identiﬁ cation

å You may receive extra hardware with your unit.

403818 www.sauder.com/servicesPage 4

35DA

CABINET RIGHT - 2

35DB

CABINET LEFT - 2

35DC

DRAWER RIGHT - 2

35DD

DRAWER LEFT - 2

FF

TWIST-LOCK

®

FASTENER - 18

FOOT - 1

GG

GROMMET - 1

II

GROMMET CAP- 1

JJ

METAL BRACKET - 18

KK

ANGLE BRACKET - 12

LL

HINGE - 2

MM

RAIL BRACKET - 4

NN

HANDLE - 2

PP

HANDLE MOUNT - 4

QQ

RR

SLIDE CAM - 4 METAL PIN - 20

SS

RUBBER SLEEVE - 16

TT

UU

WARNING LABEL - 1

WARNING

Never use this furniture with a TV that is too

large or too heavy. Severe injury or death

can occur. The TV and furniture will be

unstable and may tip.

-The TV must less than 135 lbs.

-The base of the TV must be able to sit

completely on this shelf.

-Refer to instruction book for complete safety

information.

Note: This is a permanent label. Do not try

to remove. Surface will be damaged.

02/ 02 2 6 9 2 3 2 269232

(Refer to Step 22 for proper

location and application)

TIE PLATE -2

OO

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

403818www.sauder.com/services

Page 5

BLACK 1-7/8" FLAT HEAD SCREW - 10

VV

BLACK 9/16" LARGE HEAD SCREW - 98

XX YY

GOLD 5/16" FLAT HEAD SCREW - 16

NAIL - 24

ZZ 30S

BLACK 1-9/16" FLAT HEAD SCREW - 8

15S

SILVER 5/8" MACHINE SCREW - 4

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratching your unit or the ﬂ oor.

å

To begin assembly, push a SAUDER TWIST-LOCK®

FASTENER (FF) into the large holes in the RIGHT END (A)

and LEFT END (B).

å

Repeat this step for the UPRIGHT (C) and both SHELVES (E).

403818 www.sauder.com/servicesPage 6

(18 used)

FF

Do not tighten the TWIST-LOCK® FASTENERS in this step.

A

B

å

Fasten twelve ANGLE BRACKETS (LL) to the

ENDS (A and B) and BOTTOM (F). Use twelve

BLACK 9/16" LARGE HEAD SCREWS (XX).

å

NOTE: Be sure the edges of the ANGLE BRACKETS

are even with the edges of the ENDS and BOTTOM.

Step 2

403818www.sauder.com/services

Page 7

BLACK 9/16" LARGE HEAD SCREW

(12 used in this step)

XX

(12 used)

LL

A

B

F

Surface with

TWIST-LOCK®

FASTENERS

Surface with

TWIST-LOCK®

FASTENERS

Unﬁ nished surface

Step 3

å

Fasten twelve METAL BRACKETS (KK) to the BOTTOM (F)

and BACKS (I and J). Use twelve BLACK 9/16" LARGE

HEAD SCREWS (XX).

å

NOTE: Be sure the edges of the METAL BRACKETS are even

with the edges of the BOTTOM and BACKS.

403818 www.sauder.com/servicesPage 8

I

J

F

Finished

surface

Finished

surface

BLACK 9/16" LARGE HEAD SCREW

(12 used in this step)

XX

KK

Unﬁ nished surface

å

Fasten the BACK MOLDINGS (W) to the BACKS (I and J).

Use four BLACK 9/16" LARGE HEAD SCREWS (XX) through

the BRACKETS and into the MOLDINGS.

å

NOTE: There are no pre-drilled holes in the BACK

MOLDINGS. The SCREWS will tighten into the grooves.

Step 4

403818www.sauder.com/services

Page 9

BLACK 9/16" LARGE HEAD SCREW

(4 used in this step)

XX

I

J

W

These edges should be even.

Step 5

å

Fasten the SHELVES (E) to the UPRIGHT (C). Tighten four

TWIST-LOCK® FASTENERS.

403818 www.sauder.com/servicesPage 10

C

E

Surface with

TWIST-LOCK®

FASTENERS

Surface without

TWIST-LOCK®

FASTENERS

How to use the SAUDER TWIST-LOCK

®

FASTENER

1. Insert the dowel end of the FASTENER into the hole of the

adjoining part.

NOTE: The dowel end of the FASTENER must remain fully

inserted in the hole of the adjoining part while locking

the FASTENER.

2. Tighten the FASTENER with a Phillips screwdriver as tight

as possible.

E

Surface with

TWIST-LOCK®

FASTENERS

Finished edge

Long edge with

TWIST-LOCK®

FASTENERS

Long edge with

TWIST-LOCK®

FASTENERS

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

Dowel end

å

Fasten the ENDS (A and B) to the SHELVES (E). Tighten

four TWIST-LOCK® FASTENERS.

Step 6

403818www.sauder.com/services

Page 11

B

E

A

Surface with

TWIST-LOCK®

FASTENERS

Surface without

TWIST-LOCK®

FASTENERS

Edge with ANGLE BRACKETS

Step 7

å

Fasten the TOP (D) to the ENDS (A and B) and

UPRIGHT (C). Tighten six TWIST-LOCK® FASTENERS.

403818 www.sauder.com/servicesPage 12

Curved edge

B

D

C

A

Surface with holes

å

Fasten the SHELF MOLDING (S) to the SHELVES (E).

Tighten four TWIST-LOCK® FASTENERS.

Step 8

403818www.sauder.com/services

Page 13

E

S

Curved edge

Step 9

å

Fasten the MOLDINGS (X and Y) to the ENDS (A and B). Use

eight BLACK 9/16" LARGE HEAD SCREWS (XX) through the

BRACKETS and into the MOLDINGS.

403818 www.sauder.com/servicesPage 14

BLACK 9/16" LARGE HEAD SCREW

(8 used in this step)

XX

A

B

X

Y

X

Y

These edges should be even.

å

Fasten the RAIL BRACKETS (NN) to the ENDS (A and B).

Use eight BLACK 9/16" LARGE HEAD SCREWS (XX).

Step 10

403818www.sauder.com/services

Page 15

BLACK 9/16" LARGE HEAD SCREW

(8 used in this step)

XX

NN

A

B

Step 11

å

Fasten the CABINET RIGHTS (35DA) and CABINET

LEFTS (35DB) to the ENDS (A and B) and UPRIGHT (C).

Use eight GOLD 5/16" FLAT HEAD SCREWS (YY).

403818 www.sauder.com/servicesPage 16

A

B

GOLD 5/16" FLAT HEAD SCREW

(8 used in this step)

YY

Roller end

C

å

Fasten the BOTTOM (F) to the ENDS (A and B)

and UPRIGHT (C). Use six BLACK 1-7/8" FLAT

HEAD SCREWS (VV).

Step 12

403818www.sauder.com/services

Page 17

Edge with ANGLE BRACKETS

A

B

C

F

Unﬁ nished surface

BLACK 1-7/8" FLAT HEAD SCREW

(6 used in this step)

VV

Step 13

å

Fasten the BASE (T) to the BOTTOM (F). Use four

BLACK 9/16" LARGE HEAD SCREWS (XX) through the

BRACKETS and into the BASE.

403818 www.sauder.com/servicesPage 18

F

T

BLACK 9/16" LARGE HEAD SCREW

(4 used in this step)

XX

Curved edge

å

Carefully turn your unit onto its top.

å

Insert four METAL PINS (SS) into the BACKS (I and J).

å

Insert the METAL PINS (SS) in one end of the BACKS (I and J)

into the holes in the TOP (D).

å

Fasten the BACKS (I and J) to the BOTTOM (F). Use four

BLACK 1-7/8" FLAT HEAD SCREWS (VV).

Step 14

403818www.sauder.com/services

Page 19

BLACK 1-7/8" FLAT HEAD SCREW

(4 used in this step)

VV

F

J

I

D

SS

Unﬁ nished surface

Step 15

å

Fasten the MOLDINGS (Z) to the BACKS (I and J). Use four

BLACK 9/16" LARGE HEAD SCREWS (XX) through the

BRACKETS and into the MOLDINGS.

å

Fasten the BASES (U and V) to the BOTTOM (F). Use four

BLACK 9/16" LARGE HEAD SCREWS (XX) through the

BRACKETS and into the BASES.

403818 www.sauder.com/servicesPage 20

BLACK 9/16" LARGE HEAD SCREW

(8 used in this step)

XX

F

J

I

Z

U

V

Z

Curved edge

Flat edge

La page charge ...

Sauder Corner Entertainment Credenza 403818 Mode d'emploi

Sauder Corner Entertainment Credenza 403818 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents