Dell W-AP204/205 Mode d'emploi

Marque: Dell

Modèle: W-AP204/205

Catégorie: Points d'accès WLAN

Taper: Mode d'emploi

Dell Networking W-AP200 Series Wireless Access Point

Installation Guide

The Dell Networking W-AP200 Series (W-AP204 and W-AP205) wireless access

points support the IEEE 802.11n and 802.11ac standards for high-performance

WLAN. These access points use MIMO (Multiple-in, Multiple-out) technology

and other high-throughput mode techniques to deliver high-performance, 802.11n

2.4 GHz and 802.11ac 5 GHz functionality while simultaneously supporting legacy

802.11a/b/g wireless services. The W-AP200 Series access points work only in

conjunction with a Dell Networking W-Series Mobility Controller.

The Dell W-AP200 Series access point provides the following capabilities:

 Wireless transceiver

 Protocol-independent networking functionality

 IEEE 802.11a/b/g/n/ac operation as a wireless access point

 IEEE 802.11a/b/g/n/ac operation as a wireless air monitor

 Compatibility with IEEE 802.3af PoE

 Central management configuration and upgrades using a controller

Package Contents

 W-AP204 or W-AP205 Access Point

 9/16" and 15/16” Ceiling Rail Adapters

 Installation Guide (this document)

W-AP200 Series Hardware Overview

Figure 1 W-AP200 Series LEDs

LEDs

The W-AP200 Series is equipped with four LEDs that indicate the status of the

various components of the AP.

 PWR: Indicates whether or not the W-AP200 Series is powered-on and shows

basic system status

 ENET: Indicates the status of the W-AP200 Series’ Ethernet port

 5 GHz: Indicates the status of the 802.11a/n/ac radio

 2.4 GHz: Indicates the status of the 802.11b/g/n radio

Figure 2 W-AP200 Series Side View (W-AP204 shown)

External Antenna Connectors

The W-AP204 is equipped with two external antenna connectors. The connectors

are labeled ANT0 and ANT1, and correspond to radio chains 0 and 1.

Figure 3

W-AP200 Series Bottom View

For optimal performance when using articulating direct-mount antennas,

professional installers must orient the antennas as pictured in Figure 4 below.

Figure 4 W-AP204 Antenna Orientation

Console Port

The serial console port allows you to connect the AP to a serial terminal or a laptop

for direct local management. This port is an RJ-45 female connector with the

pinouts described in Figure 5. Connect it directly to a terminal or terminal server

using an Ethernet cable.

Figure 5 Serial Port Pin-Out

Ethernet Port

W-AP200 Series is equipped with one 10/100/1000Base-T (RJ-45) auto-sensing,

MDI/MDX wired-network connectivity port. This port supports IEEE 802.3af

Power over Ethernet (PoE) compliance, accepting 48 VDC (nominal) as a standard

defined Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a

PoE midspan injector, or network infrastructure that supports PoE.

The 10/100/1000 Mbps Ethernet port is on the bottom of the AP. This port has an

RJ-45 female connector with the pin-outs shown in Figure 6.

Figure 6 Gigabit Ethernet Port Pin-Out

DC Power Socket

If PoE is not available, an optional Dell AP AC-DC adapter kit (sold separately)

can be used to power the W-AP200 Series.

Additionally, a locally-sourced AC-to-DC adapter (or any DC source) can be used

to power this device, as long as it complies with all applicable local regulatory

requirements and the DC interface meets the following specifications:

 12 VDC (+/- 5%)/18W

 Center-positive 1.7/4.0 mm circular plug, 9.5 mm length

Reset Button

The reset button can be used to return the AP to factory default settings. To reset

the AP:

1. Power off the AP.

2. Press and hold the reset button using a small, narrow object, such as a paperclip.

3. Power-on the AP without releasing the reset button. The power LED will flash

within 5 seconds.

4. Release the reset button.

The power LED will flash again within 15 seconds indicating that the reset is

completed. The AP will now continue to boot with the factory default settings.

Before You Begin

Pre-Installation Network Requirements

After WLAN planning is complete and the appropriate products and their

placement have been determined, the Dell controller(s) must be installed and

initial setup performed before the Dell APs are deployed.

For initial setup of the controller, refer to the Dell Networking W-Series ArubaOS

Quick Start Guide for the software version installed on your controller.

AP Pre-Installation Checklist

Before installing your W-AP200 Series AP, ensure that you have the following:

 CAT5e or better UTP cable of required length

 One of the following power sources:

 IEEE 802.3af-compliant Power over Ethernet (PoE) source. The POE

source can be any power source equipment (PSE) controller or midspan PSE

device

 Dell AP AC-DC adapter kit (sold separately)

 Dell Controller provisioned on the network:

 Layer 2/3 network connectivity to your access point

 One of the following network services:

 Aruba Discovery Protocol (ADP)

 DNS server with an “A” record

 DHCP Server with vendor-specific options

Summary of the Setup Process

Successful setup of an W-AP200 Series access point consists of five tasks, which

must be performed in this order:

1. Verify pre-installation connectivity.

2. Identify the specific installation location for each AP.

3. Install each AP.

4. Verify post-installation connectivity.

5. Configure each AP.

Verifying Pre-Installation Connectivity

Before you install APs in a network environment, make sure that the APs are able to

locate and connect to the controller after power on.

Specifically, you must verify the following conditions:

 When connected to the network, each AP is assigned a valid IP address

 APs are able to locate the controller

Refer to the Dell Networking W-Series ArubaOS Quick Start Guide for instructions

on locating and connecting to the controller.

Identifying Specific Installation Locations

You can mount the W-AP200 Series access point on a wall or on the ceiling. Use the

AP placement map generated by the Dell VisualRF Plan software application to

determine the proper installation location(s). Each location should be as close as

possible to the center of the intended coverage area and should be free from

obstructions or obvious sources of interference. These RF absorbers/reflectors/

interference sources will impact RF propagation and should have been accounted

for during the planning phase and adjusted for in VisualRF plan.

Identifying Known RF Absorbers/Reflectors/Interference Sources

Identifying known RF absorbers, reflectors, and interference sources while in the

field during the installation phase is critical. Make sure that these sources are taken

into consideration when you attach an AP to its fixed location. Examples of sources

that degrade RF performance include:

 Cement and brick

 Objects that contain water

 Metal

 Microwave ovens

 Wireless phones and headsets

Note: The W-AP200 Series requires Dell Networking W-Series ArubaOS 6.4.1.0 or

later.

Note: Inform your supplier if there are any incorrect, missing, or damaged parts. If

possible, retain the carton, including the original packing materials. Use these

materials to repack and return the unit to the supplier if needed.

Table 1

LED Behavior

LED Color/State Meaning

PWR Off No power to AP

Red Error condition

Green - Flashing AP booting

Green - Steady AP ready

ENET Off Ethernet link unavailable

Yellow - Steady 10/100Mbps Ethernet link established

Green - Steady 1000Mbps Ethernet link established

Flashing Ethernet link activity

5 GHz Off 5 GHz radio disabled

Yellow - Steady 5 GHz radio enabled in non-HT WLAN mode

Green - Steady 5 GHz radio enabled in HT WLAN mode

Flashing - Green 5 GHz Air or Spectrum Monitor

zHG4.2

zHG5

RWP

2.4 GHz Off 2.4 GHz radio disabled

Yellow - Steady 2.4 GHz radio enabled in non-HT WLAN mode

Green - Steady 2.4 GHz radio enabled in HT WLAN mode

Flashing - Green 2.4 GHz Air or Spectrum Monitor

Table 1

LED Behavior

LED Color/State Meaning

AP-204_01

ANT1

ANT0

AP-204_02

Serial

Console Port

TxD

GND

RxD

RJ-45 Female

Pin-Out

Direction

Input

Output

GND

Caution: FCC Statement: Improper termination of access points installed in the

United States configured to non-US model controllers will be in violation of the

FCC grant of equipment authorization. Any such willful or intentional violation may

result in a requirement by the FCC for immediate termination of operation and may

be subject to forfeiture (47 CFR 1.80).

Caution: EU Statement:

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please

refer to the D

ell Networking W-Series ArubaOS User Guide

for details on

restrictions.

Produit réseau local radio basse puissance operant dans la bande fréquence 2.4

GHz et 5 GHz. Merci de vous referrer au

Dell Networking W-Series ArubaOS User

Guide

pour les details des restrictions.

Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere

Informationen bezlüglich Einschränkungen finden Sie im D

ell Networking W-

Series ArubaOS User Guide.

Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento

alla

Dell Networking W-Series ArubaOS User Guide

per avere informazioni

detagliate sulle restrizioni.

1000Base-T Gigabit

Ethernet Port

RJ-45 Female

Pin-Out

Signal Name

BI_DC+

BI_DC-

BI_DD+

BI_DD-

BI_DA+

BI_DA-

BI_DB+

BI_DB-

Function

Bi-directional pair +C

Bi-directional pair -C

Bi-directional pair +D

Bi-directional pair -D

Bi-directional pair +A

Bi-directional pair -A

Bi-directional pair +B

Bi-directional pair -B

Note: Dell, in compliance with governmental requirements, has designed the W-

AP200 Series access points so that only authorized network administrators can

change the settings. For more information about AP configuration, refer to the

Dell

Networking W-Series ArubaOS Quick Start Guide

and

Dell Networking W-Series

ArubaOS User Guide

Caution: Access points are radio transmission devices and as such are subject

to governmental regulation. Network administrators responsible for the

configuration and operation of access points must comply with local broadcast

regulations. Specifically, access points must use channel assignments

appropriate to the location in which the access point will be used.

Dell Networking W-AP200 Series

Wireless Access Point

Installation Guide

www.dell.com

Dell Networking W-AP200 Series Wireless Access Point | Installation Guide

Part Number 0511619-01 | May 2014

Contacting Dell

Web Site Support

Main Website dell.com

Contact Information dell.com/contactdell

Support Website dell.com/support

Documentation Website dell.com/support/manuals

Aruba Wireless Networks

, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility

Management System

. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc.

Originated in the USA. All other trademarks are the property of their respective owners.

Open Source Code

Certain Aruba products include Open Source software code developed by third parties, including software code

subject to the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open

Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

reserved. This product includes software developed by Lars Fenneberg, et al.

Legal Notice

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate

other vendors’ VPN client devices constitutes complete acceptance of liability by that individual or corporation for

this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against

it with respect to infringement of copyright on behalf of those vendors.

Installing the AP

Using the Ceiling Rail Adapter

The W-AP200 Series ships with two ceiling rail adapters for 9/16” and 15/16” ceiling

rails. Additional wall mount adapters and ceiling rail adapters for other rail styles

are available as accessory kits.

1. Pull the necessary cables through a prepared hole in the ceiling tile near where

the AP will be placed.

2. Place the adapter against the back of the AP with the adapter at an angle of

approximately 30 degrees to the tabs (see Figure 7).

3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 7).

Figure 7 Attaching the Ceiling Rail Adapter

4. If necessary, connect the console cable to the console port on the back of the AP.

5. Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots

at approximately a 30-degree angle to the ceiling tile rail (see Figure 8). Make

sure that any cable slack is above the ceiling tile.

6. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks

into place on the ceiling tile rail.

Figure 8 Mounting the AP

7. On the W-AP204, install the external antennas according to the manufacturer’s

instructions, and connect the antennas to the antenna interfaces on the AP.

Connecting Required Cables

Install cables in accordance with all applicable local and national regulations and

practices.

Verifying Post-Installation Connectivity

The integrated LEDs on the AP can be used to verify that the AP is receiving power

and initializing successfully (see Table 1). Refer to the Dell Networking W-Series

ArubaOS Quick Start Guide for further details on verifying post-installation network

connectivity.

Configuring the W-AP200 Series

AP Provisioning/Reprovisioning

Provisioning parameters are unique to each AP. These local AP parameters are

initially configured on the controller which are then pushed out to the AP and

stored on the AP itself. Dell recommends that provisioning settings be configured

via the ArubaOS Web UI only. Refer to the Dell Networking W-Series ArubaOS User

Guide for complete details.

AP Configuration

Configuration parameters are network or controller specific and are configured and

stored on the controller. Network configuration settings are pushed out to the AP(s)

but remain stored on the controller.

Configuration settings can be configured via the ArubaOS Web UI or ArubaOS

CLI. Refer to their respective guides for further details: the Dell Networking

W-Series ArubaOS User Guide and Dell Networking W-Series ArubaOS Command-

Line Interface Reference Guide.

Product Specifications

Electrical

 Ethernet:

 1x 10/100/1000 auto-sensing Ethernet RJ-45 Interface

 MDI/MDX

 IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)

 Power over Ethernet (802.3af compliant), 48V DC (nominal) and 56V DC (maximum)/350mA

(see Figure 6 for pin configuration)

 Power:

 12 VDC power interface, supports powering through an AC-to-DC power adapter

 POE support on Ethernet port: 802.3af-compliant POE sourcing devices

Proper Disposal of Dell Equipment

For the most current information about Global Environmental Compliance and Dell products, visit

dell.com.

Waste of Electrical and Electronic Equipment

Dell products at end of life are subject to separate collection and treatment in

the EU Member States, Norway, and Switzerland and therefore are marked with

the symbol shown at the left (crossed-out wheelie bin). The treatment applied at

end of life of these products in these countries shall comply with the applicable

national laws of countries implementing Directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE).

European Union RoHS

Aruba Networks Inc., hereby, being the manufacturer of this product,

declares that all CE Marked Dell wireless controller and access points product

are manufactured in accordance to the provisional requirements set forth in

the RoHS Directive 2011/65/EC. A copy of the Aruba Declaration of Conformity may be obtained upon

request from: Aruba Networks Internatoinal Ltd, Building 1000, Citygate Mahon, Cork Ireland

Please include the regulatory model number located on the product’s regulatory nameplate with the

request.

India RoHS

This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling)

Rules, governed by the Ministry of Environment & Forests, Government of India.

China RoHS

Dell products also comply with China environmental declaration requirements and

are labeled with the “EFUP 10” label shown at the left.

Safety and Regulatory Compliance

For country specific restrictions and additional safety and regulatory information, refer to the multi-

language Dell Networking W-Series Safety, Environmental, and Regulatory Information document included

with the controller.

Regulatory Model Names

The following regulatory model names apply to the W-AP200 Series:

 W-AP204: APIN0204

 W-AP205: APIN0205

정소출력 무선기기 ( 무선데이터통신시스템용 무선기기 )

FCC

This device is electronically labeled. To view the FCC ID:

1. Log into the controller WebUI.

2. Navigate to Maintenance > Controller > About

FCC Class B Part 15

This device complies with Part 15 of the Federal Communications Commission (FCC) Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause

interference harmful to radio communications.

If this equipment does cause interference, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio or TV technician for help.

Complies with the Class B limits for radio noise emissions as set out in the interference-causing

equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel

brouilleur du Canada.

Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and

5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN

devices.

해당무선설비는 전파혼신의 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .

EU Regulatory Conformance

This product is CE marked according to the provisions of the R & TTE Directive

(1999/5/EC) - CE(!). Dell hereby declares that the APIN0204 / APIN0205 device models are in

compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC -CE(!)

The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at dell.com.

Canada

(i)les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites

mobiles utilisant les mêmes canaux;

(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-

5 725 MHz doit se conformer à la limite de p.i.r.e.;

(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se

conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.

De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont

désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5

850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

Medical

1. Equipment not suitable for use in the presence of flammable mixtures.

2. End product system, including power supply, must be evaluated to IEC 60601-1-1 and IEC 60601-1

by the end user.

3. Wipe with a dry cloth, no additional maintenance required.

4. No serviceable parts, the unit must be sent back to the manufacturer for repair.

5. No modifications are allowed without Dell approval.

第十二條

　　經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原

設計之特性及功能。

第十四條

　　低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有

干擾現象時，應立?停用，?改善至無干擾時方得繼續使用。

　　前項合法通信，指依電信法規定作業之無線電通信。

　　低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電

機設備之干擾。

Note: Service to all Dell Networking products should be performed by trained

service personnel only.

Caution: Maximum supported weight of the ceiling rail adapter is 3.75 kg.

Caution: Make sure the AP fits securely on the ceiling tile rail when hanging the

device from the ceiling, because poor installation could cause it to fall onto

people or equipment.

Note: If a power adapter other than the one provided by Dell is used in the US or

Canada, it should be cULus (NRTL) Listed, with an output rated 12 VDC, minimum

1.5A, marked “LPS” or “Class 2,” and suitable for plugging into a standard power

receptacle in the US and Canada.

᳝↦᳝ᆇ⠽䋼ໄᯢ

Hazardous Materials Declaration

᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance)

䚼ӊৡ⿄

(Parts)

䪙

3E

∲

+J

䬝

&G

݁Ӌ䫀

&U





໮⒈㘨㣃

3%%

໮⒈Ѡ㣃䝮

3%'(

⬉䏃ᵓ

(

PCA Boards)

hƻ ƻ ƻ ƻ ƻ

ᴎẄ㒘ӊ

(

Mechanical Sub-Assemblies)

hƻ ƻ ƻ ƻ ƻ



ƻ˖

㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼

SJ/T11363-2006

ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟǄ

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is

below the relevant threshold of the SJ/T11363-2006 standard.



h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖Ǆ

Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials

in the parts is above the relevant threshold of the SJ/T11363-2006 standard.



ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼Ǆ

This table shows where these substances may be found in the supply chain of electronic information

products, as of the date of sale of the enclosed product.

ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ

՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞ

ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰

The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are

per the symbol shown here. The Environment- Friendly Use Period is valid only when the

product is operated under the conditions defined in the product manual.

Caution: Dell access points must be installed by a professional installer. The

professional installer is responsible for ensuring that grounding is available and it

meets applicable local and national electrical codes.

Caution: RF Radiation Exposure Statement: This equipment complies with FCC RF

radiation exposure limits. This equipment should be installed and operated with a

minimum distance of 7.9 inches (20 cm) between the radiator and your body for 2.4

GHz and 5 GHz operations. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter. When operated in the 5.15 to 5.25

GHz frequency range, this device is restricted to indoor use to reduce the potential for

harmful interference with co-channel Mobile Satellite Systems.

Caution: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

Note: Aucune émission n’est permise dans la bande 5 600-5 650 MHz. Jusqu’à nouvel

avis, les dispositifs visés par la présente annexe ne doivent pas être en mesure d’émettre

dans la bande 5 600-5 650 MHz, afin de protéger les radars météorologiques

d’Environnement Canada exploités dans cette bande.

Caution: RF Déclaration sur la radioexposition: Cet équipement est conforme aux

normes IC Limites d'exposition aux rayonnements RF. Cet équipement doit être installé

et utilisé à une distance minimum de 7,9 pouces (20 cm) entre l'radiateur et votre corps

pour 2,4 GHz et 5 GHz opérations. cet émetteur ne doit pas être co-localisées ou

opérant en conjonction avec une autre antenne ou émetteur.

Dell W-AP204/205 Mode d'emploi

Marque: Dell

Modèle: W-AP204/205

Catégorie: Points d'accès WLAN

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Dell W-AP204/205 User guide

Dell W-AP204/205 Mode d'emploi

Dell W-AP204/205 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents