VTech VM321 Manuel utilisateur

®

Safe & Sound

TM

Video and audio monitor

User’s manual

w w w.v te c h p h o n e s.c o m

Models:

VM321/VM321-2

BC

Congratulations

on purchasing your new VTech product. Before using this product, please

read Important safety instructions on pages iii-iv of this manual.

This manual has all the feature operations and troubleshooting necessary

to install and operate your new VTech product. Please review this manual

thoroughly to ensure proper installation and operation of this innovative and

feature rich VTech product. For support, shopping, and everything new at

VTech, visit our website at www.vtechphones.com. In Canada, please visit

www.vtechcanada.com.

i

Register online to get an additional 3-month warranty!

Visit www.vtechphones.com.

Registration

Register your product online for enhanced

warranty support.

Product news

Learn about the latest VTech products.

Product introduction

VM321 is a video and audio monitor which consists of one parent unit

(VM321 PU) and one baby unit (VM321 BU).

VM321-2 is a video and audio monitor which consists of one parent unit

(VM321-2 PU) and two baby units (VM321-2 BU).

The parent unit may be shipped with a protective sticker covering the display.

Remove the protective sticker before use.

ii

iii

Important safety instructions

When using your equipment, basic safety precautions should always be followed to

reduce the risk of ﬁre, electric shock and injury, including the following:

Follow all warnings and instructions marked on the product.

Adult setup is required.

This product is intended as an aid. It is not a substitute for responsible and proper

adult supervision and should not be used as such.

This product is not intended for use as a medical monitor.

Do not use this product near water. For example, do not use it next to a bath tub,

wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement

or shower.

CAUTION: Use only the batteries indicated in this manual. There may be a risk of

explosion if a wrong type of battery is used for the parent unit. Use only the supplied

rechargeable battery or replacement battery pack (BT298555) for the parent unit.

Do not dispose of batteries in a ﬁre. They may explode. Dispose of used battery

according to the information in The RBRC

®

seal (see page 39).

Use only the adapters included with this product. Incorrect adapter polarity or

voltage can seriously damage the product.

Baby unit power adapter: Input 100-120V AC 50/60 Hz; output: 6V DC 800 mA

Parent unit power adapter: Input 100-120V AC 50/60 Hz; output: 6V DC 800 mA

The power adapters are intended to be correctly oriented in a vertical or ﬂoor mount

position. The prongs are not designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

Unplug the power cords before replacing batteries.

Do not cut off the power adapters to replace them with other plugs, as this causes a

hazardous situation.

Do not allow anything to rest on the power cords. Do not install this product where

the cords may be walked on or crimped.

This product should be operated only from the type of power source indicated on

the marking label. If you are not sure of the type of power supply in your home,

consult your dealer or local power company.

Do not overload wall outlets or use an extension cord.

Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

This product should not be placed in any area where proper ventilation is not

provided. Slots and openings in the back or bottom of this product are provided for

ventilation. To protect them from overheating, these openings must not be blocked

by placing the product on a soft surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or heat register.

Never push objects of any kind into this product through the slots because they may

touch dangerous voltage points or create a short circuit. Never spill liquid of any

kind on the product.

To reduce the risk of electric shock, do not disassemble this product, but take

it to an authorized service facility. Opening or removing parts of the product

other than speciﬁed access doors may expose you to dangerous voltages or

other risks. Incorrect reassembling can cause electric shock when the product is

subsequently used.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

18.

iv

Important safety instructions (continued)

You should test the sound reception every time you turn on the units or move one of

the components.

Periodically examine all components for damage.

Be aware of possible loss of privacy while using public airwaves. Conversations

may be picked up by other nursery monitors, cordless phones, scanners, etc.

Children should be supervised to ensure that they do not play with the product.

The product is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

Use and store the product at a temperature between 32

o

F and 104

o

F.

Do not expose the product to extreme cold, heat or direct sunlight. Do not put the

product close to a heating source.

Batteries should not be exposed to excessive heat such as bright sunshine or ﬁre.

Make sure the baby unit(s) and the adapter cord(s) are always out of reach of

the baby, at least 3 feet away from the baby or crib, to avoid a possible

strangulation hazard.

Never place the baby unit(s) inside the baby’s crib or playpen.

Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.

Other electronic products may cause interference with your video and audio

monitor. Try installing your video and audio monitor as far away from these

electronic devices as possible: wireless routers, radios, cellular telephones,

intercoms, room monitors, televisions, personal computers, kitchen appliances

and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a

multidisciplinary evaluation of the interference between portable wireless devices and

implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration,

WTR recommends to physicians that:

Pacemaker patients

Should keep wireless devices at least six inches from the pacemaker.

Should NOT place wireless devices directly over the pacemaker, such as in a breast

pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other

persons using wireless devices.

Electromagnetic elds (EMF)

This VTech product complies with all standards regarding electromagnetic ﬁelds (EMF).

If handled properly and according to the instructions in this user’s manual, the product is

safe to be used based on scientiﬁc evidence available today.

19.

20.

21.

22.

23.

1.

2.

3.

4.

5.

6.

7.

•

v

Table of contents

Getting started ...............................1

Parts checklist ................................. 1

Baby unit battery installation ........... 2

Baby unit installation ....................... 3

Baby unit installation options ........... 4

Tabletop to wall mount

installation ................................ 4

Parent unit battery installation ........10

Parent unit installation ....................12

Parent unit battery charging ...........13

Baby unit overview .........................14

Baby unit lights ...............................15

Parent unit overview .......................16

Parent unit lights ............................17

Parent unit display screen icons ....18

Positioning and operating range .....19

Position the video and audio

monitor ....................................19

Audio settings ...........................19

Operating range ........................19

Test your video and audio

monitor before use ..................... 20

Parent unit settings .....................21

Using the menu ..............................21

Monitoring mode ............................21

Alert tone ....................................... 22

Low battery tone alert .............. 22

No link alert .............................. 22

Sensitivity ...................................... 23

Temperature ...................................24

Minimum temperature ...............24

Maximum temperature ..............24

Temperature alert .................... 25

Temperature format ................. 25

Vibration ........................................ 26

Sound-activated screen ................. 26

LCD brightness .............................. 27

Pair/unpair CAM ............................ 27

Pair new CAM .......................... 27

Unpair CAM ............................. 28

Language....................................... 28

Baby unit operation .................... 29

Power on or off the baby unit ......... 29

Speaker volume ............................. 29

Play lullabies .................................. 29

Night vision .................................... 29

Parent unit operation .................. 30

Power on or off the parent unit ...... 30

Speaker volume ............................ 30

Zoom ............................................. 30

View ................................................31

Talk to the baby unit .......................31

Appendix ...................................... 32

Parent unit display screen

messages................................... 32

Parent unit battery ......................... 33

Troubleshooting ............................. 34

Operating range ............................. 38

Maintenance .................................. 38

The RBRC

®

seal ............................ 39

FCC and IC regulations ................. 40

FCC Part 15 ............................. 40

Industry Canada ...................... 40

RF radiation exposure

statement ............................... 40

California Energy Commission

battery charging testing

instructions..................................41

For cETL compliance only ............ 42

Limited warranty ............................ 45

Technical speciﬁcations .................47

Index ............................................. 48

1

Important

information

Parts checklist

Check to make sure the package contains the following items. Save

your sales receipt and original packaging in the event warranty service

is necessary.

* indicates replacements are available. For more information, visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or call 1 (800) 267-7377.

Getting started

User’s manual * Important

information *

Baby unit

(VM321 BU/VM321-2 BU)

(1 for VM321)

(2 for VM321-2)

Parent unit

(VM321 PU/VM321-2 PU)

Baby unit

power adapter *

(1 for VM321)

(2 for VM321-2)

Parent unit battery

compartment cover *

Battery for

parent unit *

Parent unit

power adapter *

Baby unit battery

compartment cover *

(1 for VM321)

(2 for VM321-2)

Screws *

(2 for VM321)

(4 for VM321-2)

Wall anchors *

(2 for VM321)

(4 for VM321-2)

Wall mount *

(1 for VM321)

(2 for VM321-2)

User’s manual

2

Getting started

Baby unit battery installation

You can power up the baby unit by connecting it to AC power or to four

AA alkaline batteries. Even if the baby unit is connected to AC power, we

recommend you also install four AA alkaline batteries. This guarantees

continual operation in case of a power outage.

Install four AA alkaline batteries (not supplied) into the battery compartment,

matching the polarity markings (+ and -) inside the battery compartment.

Make sure the ribbon attached inside the battery compartment is put under the

batteries and the excess ribbon is tucked in properly. Then replace the battery

compartment cover.

Do not mix old and new batteries. Do not mix alkaline and standard

(carbon-zinc) batteries.

The operating time for using AA batteries is short, only for a few hours. If you

want to monitor your baby for a long time, we recommend you connect your

baby unit to AC power.

If the baby unit will not be used for a long time, disconnect and remove the

battery to prevent possible leakage.

You can use rechargeable AA batteries for the baby unit, but the baby unit

cannot charge rechargeable batteries.

•

Gently pull the ribbon

and lift up to remove

the batteries

3

Getting started

Baby unit installation

Install the baby unit as shown below.

Make sure that the power outlet is not controlled by a wall switch. Bundle the

power cord neatly with the self-adhesive strap.

Use only the baby unit power adapters supplied with this product. To order a

replacement, visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

The baby unit power adapters are intended to be correctly oriented in a vertical

or ﬂoor mount position. The prongs are not designed to hold the plug in place if

it is plugged into a ceiling, under-the-table or cabinet outlet.

Make sure the baby units and the power adapter cords are out of reach

of children.

•

Baby unit

Power outlet not

controlled by a

wall switch

Baby unit

power adapter

Self-adhesive strap

Raise the antenna for

better reception.

4

Getting started

Baby unit installation options

The baby unit is ready for tabletop use. Use the provided wall mount if you

want to mount it on a wall. Make sure to test the reception and the baby unit

position before completing the wall mounting installation (see Test your video

and audio monitor before use on page 20).

Tabletop to wall mount installation

Option 1: Use this method to ﬁx the wall mount securely on the wall.

Place the wall mount on a wall and then use a pencil to mark the top two

holes as shown. Then remove the wall mount and drill two holes in the

wall (7/32” drill bit). Check for reception strength and camera angle before

drilling the holes.

If you drill the holes into a stud, go to step 3.

-OR-

If you drill the holes into an object other than a stud, insert the wall

anchors into the holes and tap gently on the ends with a hammer until the

wall anchors are ﬂush with the wall.

1.

2.

5

Getting started

Baby unit installation options (continued)

Align the wall mount and screws with the holes in the wall as shown. Make

sure to attach the screw in the middle hole ﬁrst so that the wall mount

position is ﬁxed. Then attach the other screw in the top hole.

Place the baby unit on the wall mount and tighten the screw into the

threaded socket at the bottom to secure the baby unit.

3.

4.

6

Getting started

Bundle the power cord neatly with the self-adhesive strap. Make sure to

keep the power adapter cord away from children’s reach.

5.

Baby unit installation options (continued)

7

Getting started

Option 2: Use this method so that you can relocate the baby unit with the wall

mount easily.

Place the wall mount on a wall and then use a pencil to mark the top and

the bottom holes as shown. Then remove the wall mount and drill two

holes in the wall (7/32” drill bit). Check for reception strength and camera

angle before drilling the holes.

If you drill the holes into a stud, go to step 3.

-OR-

If you drill the holes into an object other than a stud, insert the wall

anchors into the holes and tap gently on the ends with a hammer until the

wall anchors are ﬂush with the wall.

1.

2.

Baby unit installation options (continued)

8

Getting started

Baby unit installation options (continued)

Insert the screws into the holes and tighten the screws until only 1/4 inch

of the screws are exposed.

Place the baby unit on the wall mount and tighten the screw into the

threaded socket at the bottom to secure the baby unit. Align the holes on

the wall mount with the screws on the wall and slide the wall mount down

until it locks into place.

3.

4.

9

Getting started

Baby unit installation options (continued)

Bundle the power cord neatly with the self-adhesive strap. Make sure to

keep the power adapter cord away from children’s reach.

5.

10

Getting started

Parent unit battery installation

You can power up the parent unit by connecting it to AC power or to the

rechargeable battery provided. Even if the parent unit is connected to

AC power, we recommend you also install the battery. This guarantees

continual operation in case of a power outage.

Install the battery as shown below.

With the label THIS SIDE UP facing up, insert the small tabs of the battery

into the slots inside the battery compartment. Make sure the metallic contact

is correctly oriented as shown below. Push the battery into the battery

compartment until it clicks securely into place.

Align the battery compartment cover ﬂat against the battery compartment,

then slide it towards the center of the parent unit until it clicks into place.

1.

2.

Metallic

contact

11

Getting started

Parent unit battery installation (continued)

To replace the battery, press down on the large tab of the battery and pull it

out of the battery compartment, then follow the steps on page 10 to install

the battery.

The operating time for using the rechargeable battery is short. If you want to

monitor your baby for a long time, we recommend you connect the parent unit

to AC power.

If the parent unit will not be used for a long time, disconnect and remove the

battery to prevent possible leakage.

Use only the battery supplied with this product. To purchase a replacement

battery, visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

•

12

Getting started

Parent unit installation

Install the parent unit as shown below.

Make sure that the power outlet is not controlled by a wall switch. Bundle the

adapter cord neatly with the attached self-adhesive strap.

Parent unit

Use only the parent unit power adapter supplied with this product. To order a

replacement, visit our website at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

The parent unit power adapter is intended to be correctly oriented in a vertical or

ﬂoor mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

Make sure the parent unit and the power adapter cord are out of reach

of children.

•

Power outlet not

controlled by a

wall switch

Parent unit

power adapter

Self-adhesive

strap

If the battery

is installed,

the light on

the parent unit

turns on while

charging.

Raise the antenna

for better reception.

13

Getting started

Parent unit battery charging

Once you have installed the parent unit (see page 12) and its battery (see

page 10), press for 2 seconds to turn it on. The battery icon indicates the

battery status (see the table below). The parent unit battery is fully charged

after 12 hours of continuous charging.

When the parent unit is operating in battery mode and the battery is low, you

need to charge the parent unit without interruption for at least 30 minutes to

give the parent unit enough charge to use for a short time. When operating in

low battery condition, the parent unit displays Battery low at Parent Unit

and . The light on the parent unit ﬂashes and the parent unit plays

short beeps to alert you.

The following table summarizes the battery charge indicators and actions

to take.

Battery indicators Battery status Action

The battery icon is off and

displays.

No battery is installed but

operates using AC power,

or the battery has been

installed incorrectly.

Install the parent unit

battery. Charge without

interruption (at least

30 minutes).

The screen displays

Battery low at Parent

Unit and . The

light ﬂashes.

The battery has very little

charge and may be used

for only a short time.

Charge

without interruption

(about 30 minutes).

The battery icon becomes

solid .

The battery is fully charged. To keep the battery

charged, connect it to

AC power when not in use.

When you charge the battery initially or it is not used for a long period of time,

charge it for 12 hours continuously. It takes longer to charge the battery when

the parent unit is turned on. To shorten the charging time, turn the parent unit

off while charging.

14

Getting started

Baby unit overview

5

1

2

3

4

6

12 13 14

15

16

7

8

9

10

11

1

_

Camera

2

_

Infrared LEDs

Backup light for night vision (page 29).

3

_

(On/off)

Press and hold to turn on or off

(page 29).

4

_

Microphone

5

_

Antenna

6

_

Light sensor

7

_

(Play/stop)

Press to play lullabies (page 29).

Press to stop playing lullabies (page 29).

8

_

+

(Volume up)

Press to increase the listening volume

(page 29).

9

_

-

(Volume down)

Press to decrease the listening volume

(page 29).

10

_

(Skip)

Press to skip to the next lullaby

(page 29).

11

_

Threaded socket (1/4 in)

For installation of the provided wall

mount (page 4) or a tripod

(not provided).

12

_

Camera angle adjustment tab

Tilt to adjust camera angle.

13

_

Speaker

To listen to lullabies.

To listen to broadcasts from the

parent unit.

14

_

Temperature sensor

15

_

Battery compartment cover

16

_

Power jack

La page charge ...

VTech VM321 Manuel utilisateur

Ce manuel convient également à

VTech VM321 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents